DBELETTRONICA TELECOMUNICAZIONI SpA - RF

DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
MMT – HMT /P
DMT – HMR /P
Portable 2 GHz Microwave
Audio/Video link
User’s Manual
Release 1.0
- DB ELETTRONICA TELECOMUNICAZIONI S.p.A. - Via Lisbona, 38 - 35127 Z.I. SUD PADOVA ITALY -- Tel. (049) 870-0588 - Fax. (049) 870-0747 -
- http://www.dbbroadcast.com -
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
1 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
SAFETY NOTICES
WARNING
To avoid risks of electrical shocks or fire, only qualified personnel should execute the procedures
specified in this manual.
WARNING
When the protective covers of any device or component connected to a 110 / 240 VAC source by a
power cord are removed, voltages and currents dangerous to life may be exposed.
WARNING
Contact with 110 / 240 Volts of alternating current and associated direct current and voltages can be
fatal.
1 DANGEROUS 1
RISK OF ELECTRICAL SHOCK DO NOT OPEN
CAUTION
To reduce the risks of electrical shock, do not remove the cover (or the back). Refer, for servicing,
to qualified service personnel. This installation should be done by a qualified person and should
conform to all local applicable laws.
NOTICE: ALL THE SPECIFICATIONS AND TECHNICAL INFORMATION IN THIS MANUAL ARE SUBJECT TO
CHANGE WITHOUT NOTICE
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
2 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
INDEX
1.
MMT-HMT /P GENERAL DESCRIPTION .................................................................................................... 5
2.
MMT-HMT /P FUNCTIONAL DESCRIPTION.............................................................................................. 6
3.
TX VIDEO STAGE ......................................................................................................................................... 11
3.1
4.
TX VIDEO STAGE PARTS LIST ............................................................................................................. 18
TX AUDIO SUBCARRIER STAGE ............................................................................................................... 20
4.1
5.
TX AUDIO SUBCARRIER STAGE PARTS LIST..................................................................................... 25
MODULATION STAGE................................................................................................................................. 27
5.1
6.
MODULATION STAGE PARTS LIST...................................................................................................... 31
FILTER STAGES............................................................................................................................................ 33
6.1
6.2
7.
BAND PASS FILTER GENERAL DESCRIPTION.................................................................................... 33
OUTPUT LOW PASS FILTER GENERAL DESCRIPTION...................................................................... 33
TX AMPLIFIER SECTION............................................................................................................................ 34
7.1
7.2
8.
GENERAL DESCRIPTION ....................................................................................................................... 34
TX PRE AMPLIFIER PARTS LIST (DB 9606-018) .................................................................................. 35
TX AMPLIFIER POWER SUPPLY SECTION............................................................................................. 36
8.1
9.
TX AMPLIFIER POWER SUPPLY PARTS LIST ..................................................................................... 37
DMT-HMR /P FUNCTIONAL DESCRIPTION ............................................................................................ 38
10.
10.1
11.
11.1
12.
12.1
13.
13.1
13.2
14.
14.1
14.2
RX VIDEO STAGE ..................................................................................................................................... 43
RX VIDEO STAGE PARTS LIST ............................................................................................................. 50
RX AUDIO SUBCARRIER STAGE ........................................................................................................... 52
RX AUDIO SUBCARRIER PARTS LIST.................................................................................................. 56
DEMODULATOR STAGE ......................................................................................................................... 58
DEMODULATOR STAGE PARTS LIST .................................................................................................. 60
RX AMPLIFIER SECTION........................................................................................................................ 62
GENERAL DESCRIPTION ....................................................................................................................... 62
RX AMPLIFIER PARTS LIST .................................................................................................................. 63
TX /RX POWER SUPPLY BOARDS ......................................................................................................... 64
MMT - DMT PWR SUPPLY PARTS LIST................................................................................................ 66
HMT - HMR POWER SUPPLY PARTS LIST ........................................................................................... 68
15.
TX AND RX TECHNICAL SPECIFICATIONS ........................................................................................ 69
16.
INSTALLATION ......................................................................................................................................... 71
16.1
16.2
16.3
17.
17.1
17.2
INSTALLING MMT-HMT /P.................................................................................................................... 71
INSTALLING DMT-HMR /P .................................................................................................................... 73
CHANNEL SETTING ............................................................................................................................... 75
APPENDIX A............................................................................................................................................... 77
XLR AUDIO CONNECTORS PINOUTS FOR MMT ................................................................................ 77
XLR AUDIO CONNECTORS PINOUTS FOR DMT................................................................................. 78
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
3 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
FIGURES INDEX
FIG. 2.1 - MMT-HMT /P FRONT VIEW..................................................................................................................... 7
FIG. 2.2 - MMT-HMT /P UP LAYOUT ...................................................................................................................... 8
FIG. 2.3 - MMT-HMT /P DOWN LAYOUT ................................................................................................................ 9
FIG. 2.4 - TRANSMITTER GENERAL BLOCK DIAGRAM .................................................................................... 10
FIG. 3.1 - TX VIDEO STAGE GENERAL ELECTRICAL SCHEMATIC ................................................................. 11
FIG. 3.2 - TX VIDEO INPUT ELECTRICAL SCHEMATIC ..................................................................................... 12
FIG. 3.3 - TX VIDEO MIX ELECTRICAL SCHEMATIC......................................................................................... 13
FIG. 3.4 - TX VIDEO PRECORRECTOR ELECTRICAL SCHEMATIC................................................................... 14
FIG. 3.5 - TX VIDEO MEASURES ELECTRICAL SCHEMATIC ............................................................................ 15
FIG. 3.6 - TX VIDEO DISPLAY ELECTRICAL DIAGRAM .................................................................................... 16
FIG. 3.7 - TX VIDEO STAGE COMPONENT LAYOUT (DB 9704-019) ................................................................. 17
FIG. 4.1 - TX AUDIO SUBCARRIER STAGE GENERAL ELECTRICAL SCHEMATIC ........................................ 20
FIG. 4.2 - TX AUDIO SUBCARRIER INPUT ELECTRICAL SCHEMATIC ............................................................ 21
FIG. 4.3 - TX AUDIO SUBCARRIER FILTER ELECTRICAL SCHEMATIC........................................................... 22
FIG. 4.4 - TX AUDIO SUBCARRIER PLL / VCO ELECTRICAL SCHEMATIC...................................................... 23
FIG. 4.5 - TX AUDIO SUBCARRIER STAGE COMPONENT LAYOUT (DB 9407-017)......................................... 24
FIG. 5.1 - MODULATION STAGE GENERAL ELECTRICAL SCHEMATIC.......................................................... 27
FIG. 5.2 - MODULATION STAGE VCO ELECTRICAL SCHEMATIC ................................................................... 28
FIG. 5.3 - MODULATION STAGE PLL ELECTRICAL SCHEMATIC..................................................................... 29
FIG. 5.4 - MODULATION STAGE COMPONENT LAYOUT (DB 9506-005).......................................................... 30
FIG. 6.1 - BAND PASS FILTER ELECTRICAL SCHEMATIC................................................................................. 33
FIG. 7.1 - TX PRE AMPLIFIER ELECTRICAL SCHEMATIC (DB 9606-018)......................................................... 34
FIG. 7.2 - TX PRE AMPLIFIER COMPONENT LAYOUT (DB 9606-018)............................................................... 35
FIG. 7.3 - TX 2/5W POWER AMPLIFIER SCHEMATIC.......................................................................................... 35
FIG. 8.1 - TX AMPLIFIER POWER SUPPLY ELECTRICAL SCHEMATIC............................................................ 36
FIG. 8.2 - TX AMPLIFIER POWER SUPPLY COMPONENT LAYOUT (DB 9610-002).......................................... 37
FIG. 9.1 - DMT-HMR /P FRONT VIEW .................................................................................................................. 39
FIG. 9.2 - DMT-HMR /P UP LAYOUT..................................................................................................................... 40
FIG. 9.3 - DMT-HMR /P DOWN LAYOUT.............................................................................................................. 41
FIG. 9.4 - RECEIVER GENERAL BLOCK DIAGRAM ............................................................................................ 42
FIG. 9.5 – RX VIDEO STAGE GENERAL ELECTRICAL SCHEMATIC ................................................................ 43
FIG. 9.6 - RX VIDEO INPUT ELECTRICAL SCHEMATIC..................................................................................... 44
FIG. 9.7 - RX VIDEO SC AUDIO ELECTRICAL SCHEMATIC .............................................................................. 45
FIG. 9.8 - RX VIDEO PROCESSOR ELECTRICAL SCHEMATIC .......................................................................... 46
FIG. 9.9 - RX VIDEO MEASURES ELECTRICAL SCHEMATIC............................................................................ 47
FIG. 9.10 - RX MEASURES CONTROL ELECTRICAL SCHEMATIC .................................................................... 48
FIG. 9.11 - RX VIDEO STAGE COMPONENT LAYOUT (DB 9704-018) ............................................................... 49
FIG. 9.12 – RX AUDIO SUBCARRIER STAGE GENERAL ELECTRICAL SCHEMATIC...................................... 52
FIG. 9.13 - RX AUDIO SUBCARRIER FILTER ELECTRICAL SCHEMATIC......................................................... 53
FIG. 9.14 - RX AUDIO SUBCARRIER STAGE BALAN/ OUTPUT ELECTR. SCHEMATIC .................................. 54
FIG. 9.15 - RX AUDIO SUBCARRIER STAGE COMPONENT LAYOUT (DB 9704-016)....................................... 55
FIG. 10.1 - DEMODULATOR STAGE ELECTRICAL SCHEMATIC....................................................................... 58
FIG. 10.2 - DEMODULATOR STAGE COMPONENT LAYOUT (DB 9601-005) .................................................... 59
FIG. 12.5 - RX AMPLIFIER ELECTRICAL DIAGRAM (DB 9606-019)................................................................... 62
FIG. 12.1 - RX AMPLIFIER COMPONENT LAYOUT (DB 9606-019) .................................................................... 63
FIG. 11.1 - MMT - DMT PWR SUPPLY ELECTRICAL SCHEMATIC .................................................................... 64
FIG. 11.2 - MMT - DMT PWR SUPPLY COMPONENT LAYOUT (AL8GHZ) ........................................................ 65
FIG. 11.3 - HMT - HMR POWER SUPPLY ELECTRICAL SCHEMATIC................................................................ 67
FIG. 11.4 - HMT - HMR POWER SUPPLY COMPONENT LAYOUT (DB 9602-011).............................................. 68
FIG. 14.1 - MMT-HMT /P INSTALLATION............................................................................................................ 72
FIG. 14.2 - DMT-HMR /P INSTALLATION ............................................................................................................ 74
FIG. 14.3 - TRANSMITTER JUMPERS (VCO BOARD ON MMT) .......................................................................... 75
FIG. 14.4 - RECEIVER JUMPERS (L.O. BOARD ON DMT).................................................................................... 76
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
4 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
1. MMT-HMT /P GENERAL DESCRIPTION
The MMT-HMT /P is a portable 2 GHz microwave link that can carry simultaneously 1 video and up
to 2 high-quality 15 kHz analog audio programs.
The audio channels are fully compatible with DB digital audio codecs TD/16 and RD/16
(2-channels).
With the MMT-HMT /P, the following performances are guaranteed:
-A/V intermodulation is almost canceled;
-system accepts simultaneously 1 video, up to 4 digital audio programs, and up to 4 x 4800 bps data
channels.
- RF frequency channels are easy to change with a 125 kHz steps digital PLL. No tuning is required
within 100 MHz range.
- All circuits are fitted into boxes suitable to be mounted at the rear of parabolic antennas with direct
connection to the microwave feeder.
DB parabolic antennas enable the direct connection to the microwave feeder without wave-guide
losses.
A front panel digital multimeter and alarms permit to check audio and video levels, RF signal level,
PLL lock and squelch status. The equipment meets or exceeds the international standards for safety
and electrical specifications.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
5 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
2. MMT-HMT /P FUNCTIONAL DESCRIPTION
The 2 GHz MMT-HMT /P transmitter is composed of two fundamental parts:
I) MMT (Microwave TV Modulator)
This is an audio/video microwave TV circuit, synthesized, 1.3 to 2.7 GHz band -2 dBm output with
the following functions:
- Video signal processing
- 7.500 MHz, 8.065 MHz subcarrier modulation
- RF video + audio 1.3 to 2.7 GHz (-2dBm output power level)
As seen in Fig. 2.4 the circuit is composed of:
1) Video processor stage with:
75 Ω BNC input
signal attenuation
pre-emphasis circuit
low pass filtering
delay group pre-corrector
adjustable modulation
Video and subcarriers signals addition
2) Up to 2 subcarriers stages with:
600 Ω XLR CANON input
balun transformer
adjustable modulation
pre-emphasis circuit
low pass filtering
7.500 MHz or 8.065 MHz modulation
band-pass filtering
3) 1.3 – 2.7 GHz PLL carrier modulation of video and audio signals.
4) System check (PLL locking, depth modulation measurement and power supply presence)
II) HMT (Microwave 1.3 to 2.7 GHz Amplifier)
It consists of a wide band microwave amplifier in the 1.3 to 2.7 GHz band with –2dBm input and 1W
or 5W output.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
6 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 2.1 - MMT-HMT /P FRONT VIEW
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
7 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 2.2 - MMT-HMT /P UP LAYOUT
1) Video stage (DB 9704-019)
4) Power supply (+12V) (AL8GHz)
2) Audio subcarrier stage (DB 9704-017)
5) Transformer
3) Power supply (+8V,-12V) (DB 9602-011)
6) VCO stage
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
8 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 2.3 - MMT-HMT /P DOWN LAYOUT
1)
2)
3)
4)
5)
6)
Amplifiers Power Supply
Audio Subcarrier
Output Low Pass Filter
Preamplifier Stage
Band Pass Filter
Power Amplifier
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
9 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 2.4 - TRANSMITTER GENERAL BLOCK DIAGRAM
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
10 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
3. TX VIDEO STAGE
Fig. 3.1 - TX VIDEO STAGE GENERAL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
11 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 3.2 - TX VIDEO INPUT ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
12 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 3.3 - TX VIDEO MIX ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
13 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 3.4 - TX VIDEO PRECORRECTOR ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
14 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 3.5 - TX VIDEO MEASURES ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
15 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 3.6 - TX VIDEO DISPLAY ELECTRICAL DIAGRAM
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
16 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 3.7 - TX VIDEO STAGE COMPONENT LAYOUT (DB 9704-019)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
17 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
3.1 TX VIDEO STAGE PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________
1
2
4
14
3
4
5
6
7
8
9
10
11
12
1
2
2
1
1
1
1
3
2
1
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
7
2
1
1
2
1
2
1
1
9
1
3
7
5
1
7
3
1
1
2
1
8
5
5
2
2
9
40
41
42
43
2
1
1
1
C1,C10,C63,C56
470u
C2,C3,C16,C17,C23,C33,C34, 100n
C39,C40,C41,C44,C45,C46,C66
C4
270p
C7,C5
330p
C8,C6
220p
C9
82p
C11
120p
C12
1500pF
C13
150pF
C14,C15,C27
10n
C19,C20
C47
1n
C48
C22,C24,C25,C26,C42,C43,C48 10u
C36,C61
220n
C37
10p
C38
22u
C50,C54
47p
C51
33p
C52
68p
C53
39p
C55
4p7
D1,D2,D3,D4,D5,D6,D7,D8,D9 1N4148
D10
9V1
F1,F2,F3
JP1,JP2,JP4,JP9,JP11→JP13 JP3
JP3,JP5,JP6,JP7,JP10
JP2
J1
BNC
J2,J5,J6,J7,J8,J9,J11
SMB
J3,J4,J10
L1
10Uh
L2
6u8
Q2,Q1
2N2222
Q3
BF245
R1,R2,R3,R4,R51,R57,R66,R78 100
C28,C29,C30,C31,C35
0R
R5,R11,R14,R15,R17
75R
R6,R12
274R
R7,R8
2K2
R9,R24,R25,R26,R28,R39,R42
R55,R71
1K
R10,R58
4K7
R13
47R5
R16
301R
R18
18R
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
Electr Cap 25V
POLY. CAP.
cer. cap.
cer. cap.
cer. cap.
cer. cap. NP0
cer. cap. NP0
POLY. cap.
POLY. cap.
POLY. cap.
Mur. brown
Cer.
Elec. cap. 25V
POLY. cap.
cer. cap. NP0
Elec. Cap. 25V
NPO
NPO
NPO
NPO
NPO
DIODE SI
Zener diode
EMI
JUMPER X3
JUMPER X2
CS 90°
SMB CS
CON14
inductance
inductance
NPN transistor
FET transistor
RES 1/4W
1/4W
1/4W 1%
1/4W 1%
1/4W
1/4W 1%
1/4W 1%
1/4W1%
1/4W 1%
1/4W 1%
18 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
1
2
1
5
1
3
2
11
1
1
1
4
1
1
2
1
1
5
1
3
3
1
1
1
1
1
R19
R20,R22
R21
R31,R32,R33,R34,R43
R40
R45,R47,R48
R46,R49
R50,R52,R53,R54,R59,R60,
R61,R62,R63,R64,R81
R56
R65
R70
R72,R73,R74,R75
R76
R77
R79,R80
R29
R41
R35,R36,R37,R38,R44
R30
T1,T2,T3
U1,U2,U3
U4
U5
U6
U7
U8
15K
680R
6K8
2K7
1K5
10K
20K
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W 1%
1/4W
10K
1/4W
100K
Trim. MG RV
560R
1/4W
330R
1/4W
56R
1/4W
68R
1/4W
470R
1/4W
22k
1/4W
2K
Trim MG RV
10K
Trim
1K
Trim MG RV
10K
Trim MG RV
RED
Style 5
AD818
TL084
79L05
4093 CMOS I.C.
4029 CMOS I.C.
4051 CMOS I.C.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
19 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
4. TX AUDIO SUBCARRIER STAGE
Fig. 4.1 - TX AUDIO SUBCARRIER STAGE GENERAL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
20 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 4.2 - TX AUDIO SUBCARRIER INPUT ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
21 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 4.3 - TX AUDIO SUBCARRIER FILTER ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
22 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 4.4 - TX AUDIO SUBCARRIER PLL / VCO ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
23 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 4.5 - TX AUDIO SUBCARRIER STAGE COMPONENT LAYOUT (DB 9407-017)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
24 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
4.1 TX AUDIO SUBCARRIER STAGE PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________
1
16
2
3
4
5
6
7
cap.
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
3
2
5
2
7
8
C1,C3,C4,C16,C17,C19,C20,
100n
C21,C22,C23,C32,C37,C45,
C49,C61,C63
C5,C6,C7
4n7
C8,C9
100p
C10,C11,C42,C43,C57
10p
C13,C12
330n
C24,C25,C38,C44,C50,C59,C60
10u
C26,C27,C28,C29,C30,C31,C33,C34
2
4
1
1
2
1
2
1
2
9
6
2
1
1
2
1
1
1
1
2
1
3
2
2
5
1
1
4
1
1
2
1
1
1
1
1
C35,C36
C46,C56,C62,C58
C51
C52
C55,C53
C54
D2,D1
D3
F1,F2
JP1,→,JP9,
JP10,→,JP15
J1,J4
J2
J3
L2,L1
L3
L4
L5
Q1
Q3,Q2
R1
R2,R5,R10
R3,R4
R6,R17
R7,R8,R41,R46,R51
R9
R12
R13,R16,R47,R56
R14
R15
R19,R18
R20
R21
R22
R23
R24
poly. cap.
poly. cap.
cer. cap.
cer. cap.
poly. cap.
Elect cap. 25V
3n3
poly.
68p
10n
1u
220p
270p
470n
1N4148
BB130
EMI
JP2
JP
cer. cap. NP0
POLY. cap.
POLY. cap.
CER. cap.
CER. cap.
POLY. cap.
DIODE
Varicap
EMI filters
JUMPER X2
JUMPER X2
CON 14p
SMB CS
XLR
Cannon CS F
10u
Inductance
STYLE 5 Inductance
4u7
Inductance
10m
Inductance
U310
FET transistor
BC237 transistor NPN
680R
RES 1/8W
12K1
RES 1/4W 1%
31K6
RES 1/4W 1%
169K
RES 1/4W 1%
1K
RES 1/4W 1%
9K53
RES 1/4W 1%
10K
TRIMMER MG P
10K
RES 1/4W
10K
TRIMMER MG RV
100K
RES 1/4W
301K
RES 1/4W 1%
3K57
RES 1/4W 1%
4K64
RES 1/4W 1%
4K02
RES 1/4W 1%
2K61
RES 1/4W 1%
536R
RES 1/4W 1%
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
25 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
1
1
6
1
1
3
3
2
1
1
1
1
1
1
1
1
1
3
1
4
1
1
1
R25
R26
R27,→,R32
R55
R33
R34,R35,R54
R36,R37,R38
R39,R57
R40
R42
R43
R44
R45
R48
R49
R50
R52
T1,T2,T3
U1
U2,U3,U4,U5
U6
U7
Y1
2K74
RES 1/4W 1%
1K91
RES 1/4W 1%
3K01
RES 1/4W 1%
1K5
RES 1/4W 1%
3K3
RES 1/4W
2K2
RES 1/4W
2K
TRIM MG RV
47R
RES 1/4W
220K
RES 1/4W
68R
RES 1/4W
39K
RES 1/4W
5K6
RES 1/4W
82R
RES 1/4W
10R
RES 1/4W
470R
RES 1/4W
220R
RES 1/4W
120R
RES 1/4W
TOKO
Inductances
TL084 OP. AMP.
TL082 OP. AMP.
78L08 Voltage reg
MC145151 PLL
2.048MHz Quartz Crystal
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
26 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
5. MODULATION STAGE
Fig. 5.1 - MODULATION STAGE GENERAL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
27 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 5.2 - MODULATION STAGE VCO ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
28 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 5.3 - MODULATION STAGE PLL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
29 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 5.4 - MODULATION STAGE COMPONENT LAYOUT (DB 9506-005)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
30 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
5.1 MODULATION STAGE PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________________
1
2
3
4
5
1
2
2
3
11
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
2
1
1
2
3
1
1
1
3
2
1
1
1
1
1
1
1
2
1
2
4
1
1
1
1
1
1
6
3
1
1
2
2
2
1
C1
C2,C3
C10,C11
C12,C13,C20
C14,C72,C73,C75,C76,C78,
C79,C83,C85,C92,C93
C15,C16
C17
C18
C20,C64
C21,C84,C86
C22
C65
C67
C87,C88,C98
C90,C89
C94
C95
C96
C97
C99
D1
D7
JP1,JP2
JP3
J1,J2
L7,L20,L23,L24
L19
L22
L25
Q4
Q5
Q6
R1,R2,R3,R4,R5,R14
R6,R7,R52
R8
R9
R11,R12
R58,R13
R56,R53
R54
1p0 CER HQ SMD
3p3 CER HQ SMD
2u2 CER SMD
220n CER SMD
1n CER SMD
100n CER SMD
56p CER SMD
ORANGE VAR. CAP. SMD
220u ELECT CAP SMD
33u ELECT CAP SMD
10u ELECT CAP SMD
10u TANTALUM
10n CER SMD
1n feed-trough CAP
10n CER SMD
1n CER SMD
4u7 ELECT CAP SMD
10u ELECT CAP
1n CER SMD
33u ELECT CAP SMD
1N4148 Diode SMD
BB811 Diode Varicap SMD
JP2 JUMPER 2 poles
JP2 JUMPER 2 poles
SMB connectors
47u Inductance SMD
.47u Inductance SMD
25mm Coaxial cable
VK200 Inductance
INA10386 Micro int. amp.
AT-41485 Micro int. amp.
MSA1104 Microw int. amp.
100k R. SMD
15K R. SMD
4K7 R. SMD
1K R. SMD
220K R. SMD
100R R. SMD
18R R. SMD
150R R. SMD
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
31 /78
DB
ITEM
QUANTITY
ELETTRONICA TELECOMUNICAZIONI S.p.A.
REFERENCE
PART
_______________________________________________________________________________________________
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
4
1
1
1
1
1
1
2
2
1
1
1
1
1
1
R55,R57,R63,R64
R59
R60
R61
R62
R65
R66
R67,R68
SW1,SW2
U2
U3
U6
U7
U8
Y1
300R R. SMD
180R R. SMD
220R R. SMD
2K2 R. SMD
22K R. SMD
75R R. SMD
10R R. SMD
390R R. SMD
DIP SW 8 Dip switches
MC145151 Integr cir SMD
LM358 Integr cir SMD
78L05 Voltage reg.
MB506 Integr cir SMD
79L12 Voltage reg.
4.00MHZ quartz cry SMD
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
32 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
6. FILTER STAGES
6.1 BAND PASS FILTER GENERAL DESCRIPTION
The pass band filter permits to obtain a desired frequency by means a multiply of its input frequency.
Fig. 6.1 - BAND PASS FILTER ELECTRICAL SCHEMATIC
6.2 OUTPUT LOW PASS FILTER GENERAL DESCRIPTION
The output low pass filter permits to eliminate the harmonic and spurious emission of the
transmitting frequency, and they are taken below the nominal value required by international
standards.
No settings or adjustments are required even in case of transmitting frequency change, within the
maximum limits that we have indicated (± 20 MHz from pre-imposed transmission frequency).
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
33 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
7. TX AMPLIFIER SECTION
7.1 GENERAL DESCRIPTION
The amplifier section is basically composed of a preamplifier (DB 9606-018 - 30 dB gain) that
receive the input signal at 1.3 - 2.7 GHz, and a power amplifier stage that furnish 2 or 5W output
power.
The electrical schematic and layout components are following indicated.
Fig. 7.1 - TX PRE AMPLIFIER ELECTRICAL SCHEMATIC (DB 9606-018)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
34 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 7.2 - TX PRE AMPLIFIER COMPONENT LAYOUT (DB 9606-018)
7.2 TX PRE AMPLIFIER PARTS LIST (DB 9606-018)
ITEM QUANTITY REFERENCE
PART
_________________________________________________
1
1
C1
10u Elett.SMD
2
3
C2,C3,C4
100n SMD
3
3
C5,C6,C7
100p SMD
4
6
R1,R2,R4,
R5,R7,R8
330R SMD
6
2
R3,R6
18R SMD
7
1
U1
7805
8
1
U2
INA 10386
9
1
U3
UNA 25
Fig. 7.3 - TX 2/5W POWER AMPLIFIER SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
35 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
8. TX AMPLIFIER POWER SUPPLY SECTION
Fig. 8.1 - TX AMPLIFIER POWER SUPPLY ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
36 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 8.2 - TX AMPLIFIER POWER SUPPLY COMPONENT LAYOUT (DB 9610-002)
8.1 TX AMPLIFIER POWER SUPPLY PARTS LIST
ITEM
QUANTITY REFERENCE TYPE
PART
_________________________________________________________________
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
1
2
2
1
1
1
2
1
1
1
1
1
C1
C2,C5
C3
C4,C8
C6,C7
C9
Q1
L1
J2,J3
Q2
R1
R5
R3
R4
Electrolytic capacitor 63V
Polyester capacitor 63V
Ceramic capacitor
Electrolytic capacitor 63V
Electrolytic capacitor 50V
Polyester. capacitor 63V
Integrated circuit
Inductor
Morsetto CSV 2 pin
Integrated circuit
Resistor 1/4W
Resistor 1/4W
Resistor
Trimmer mul.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
2200u
100n
1n
4u7
2200u
1u
SI8023
BSN0510
AK7002VIE
STR7103
1M
680R
0R012 6A
10k
37 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
9. DMT-HMR /P FUNCTIONAL DESCRIPTION
The 2 GHz receiver is composed of two fundamental parts:
I) DMT (Microwave TV Demodulator)
DMT performs the following functions:
- Global signal (Video and subcarriers) demodulation at 70 MHz.
- Video signal processing.
- Subcarriers signals (7500, 8065 kHz) demodulation.
As seen in block diagram, the circuit is composed of :
1) Video and subcarrier IF (70 MHz) demodulation stage with:
amplification
mixer
band-pass filter
demodulator
2) Video processing stage with:
low-pass filter
delay group pre corrector
adjustable amplification
deemphasis circuit
75 Ω BNC output
3) Four subcarriers demodulation stage with:
band-pass filter
demodulation (signal at 7500, 8065 KHz)
adjustable amplification
deemphasis circuit
low-pass filter
balun transformer
600 Ω XLR CANON output
II) HMR (Head Microwave Receiver)
It consists of a wideband receiver in the 1.3 to 2.7 GHz band with input level range from –-90dBm
to –15dBm.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
38 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 9.1 - DMT-HMR /P FRONT VIEW
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
39 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 9.2 - DMT-HMR /P UP LAYOUT
1) Video stage (DB 9704-018)
2) Audio subcarrier stage (DB 9704-016)
3) Power supply (+8V,-2V) (DB 9602-011)
4) Power supply (+12V) (AL8GHz)
5) Transformer
6) VCO stage
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
40 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 9.3 - DMT-HMR /P DOWN LAYOUT
1)Video Demodulator 70MHz.
2,4,6) Bandpass Filter 2 GHz.
3,5) Front end
7) Connection to the feeder
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
41 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 9.4 - RECEIVER GENERAL BLOCK DIAGRAM
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
42 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
10. RX VIDEO STAGE
Fig. 10.1 – RX VIDEO STAGE GENERAL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
43 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 10.2 - RX VIDEO INPUT ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
44 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 10.3 - RX VIDEO SC AUDIO ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
45 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 10.4 - RX VIDEO PROCESSOR ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
46 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 10.5 - RX VIDEO MEASURES ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
47 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 10.6 - RX MEASURES CONTROL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
48 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 10.7 - RX VIDEO STAGE COMPONENT LAYOUT (DB 9704-018)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
49 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
10.1 RX VIDEO STAGE PARTS LIST
ITEM QUANTITY REFERENCE
PART
_______________________________________________________________________________________
1
2
8
11
3
4
5
6
1
1
1
13
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
4
2
1
1
3
2
2
1
1
1
4
6
1
1
1
1
1
1
6
1
1
5
6
5
5
1
3
1
1
6
1
1
1
3
2
8
1
C1,C3,C8,C12,C40,C42,C46,C49
10n POLY. cap.
C2,C4,C9,C13,C39,C41,C45,
10u Elec. cap. 25V
C48,C55,C56,C58
C5
47p CER. cap.
C6
Mur. brown
C7
Mur. green
C10,C11,C19,C20,C30,C31,C53,C54,
100n POLY. cap.
C57,C59,C60,C75,C76
C14,C21,C29,C72
470u Elec. cap. 25V
C16,C71
220n POLY. cap.
C17
10p CER. cap.
C18
22u Elec. cap. 25V
C22,C25,C27
220p cer. cap.
C23,C50
100p cer. cap. NP0
C24,C28
330p cer. cap.
C26
82p cer. cap. NP0
C32
4n7 Poly. cap.
C33
680p Poly. cap.
C34,C35,C36,C37
33p CER. cap.
C38,C43,C44,C47,C52,C61
1n CER. cap.
C51
1u Elec. cap. 25V
C62
33p cer. cap. NP0
C63
68p cer. cap. NP0
C64
39p cer. cap. NP0
C65
47p cer. cap. NP0
C66
4p7 cer. cap. NP0
D1,D2,D3,D4,D5,D6
1N4148 DIODE
D7
5V1 Zener diode
D8
9V1 Zener diode
F1,F2,F3,F4,F5
EMI EMI filters
JP1,JP2,JP6,JP7,JP8,JP9
JP2 JUMPER X2
JP3,JP4,JP5,JP10,JP11
JP3 JUMPER X3
J1,J2,J3,J4,J5
SMB smb connector
J6
BNC BNC connector
J7,J8,J9
CON14
L1
4u7 inductance
L3
33uH inductance
Q1,Q2,Q3,Q4,Q5,Q6
2N2222 transistor NPN
Q7
BC307 TRANSISTOR PNP
Q8
BC237 TRANSISTOR NPN
R1
15K RES 1W4
R2,R4,R9
680R RES 1W4
R3,R69
6K8 RES 1W4
R5,R20,R67,R84,→,R88
100R RES 1W4
R6
2K TRIMER MG RV
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
50 /78
DB
ITEM
QUANTITY
ELETTRONICA TELECOMUNICAZIONI S.p.A.
REFERENCE
PART
_______________________________________________________________________________________________
44
45
46
47
48
49
50
51
7
1
1
6
3
2
1
17
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
1
1
1
2
1
1
1
5
4
4
1
1
1
1
1
1
1
2
4
1
3
2
2
1
1
1
1
R7,R8,R10,R24,R30,R53,R55
R29
R11
R12,R27,R32,R37,R38,R39,
R13,R15,R16
R14,R18
R17
R19,R21,R22,R23,R26,R56,
R58,R59,R61,R63,R64,R71,
R72,R74,R75,R76,R77
R25
R28
R31
R33,R35
R34
R36
R40
R41,R44,R47,R50,R82
R42,R46,R49,R51
R43,R45,R48,R52
R54
R57
R60
R62
R65
R66
R68
R73,R70
R78,R79,R80,R81
R83
T1,T2,T3
U1,U3
U2,U4
U5
U6
U7
U8
1K RES 1W4
2K2
10K TRIMMER
10k RES 1W4 1%
10K RES 1W4 1%
20K RES 1W4
4K7 RES 1W4
10K RES 1W4
20K TRIMMER MG RV
0R RES 1W4
8K2 RES 1W4
154R RES 1W4 1%
95R3 RES 1W4 1%
301R RES 1W4 1%
18R RES 1W4 1%
390R RES 1w8
33K RES 1w4
1K2 RES 1W4
10K TRIMMER MG RV
22K RES 1W4
33K RES 1W4
50K TRIMMER MG RV
100K RES 1W4
56K RES 1W4
47K RES 1W4
560R RES 1W4
56R RES 1W4
390K RES 1W4
STYLE 5R Inductance
AD818 Op. amp.
TL084 Op. amp.
79L05 Voltage reg.
4093 CMOS I.C.
4029 CMOS I.C.
4051 CMOS I.C.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
51 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
11. RX AUDIO SUBCARRIER STAGE
Fig. 11.1 – RX AUDIO SUBCARRIER STAGE GENERAL ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
52 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 11.2 - RX AUDIO SUBCARRIER FILTER ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
53 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 11.3 - RX AUDIO SUBCARRIER STAGE BALAN/ OUTPUT ELECTR. SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
54 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 11.4 - RX AUDIO SUBCARRIER STAGE COMPONENT LAYOUT (DB 9704-016)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
55 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
11.1 RX AUDIO SUBCARRIER PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________________
1
18
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
1
2
5
3
2
4
2
2
2
1
2
3
3
8
1
1
1
1
1
2
2
4
2
1
8
2
2
1
2
1
1
1
1
1
1
1
2
2
1
C1,C3,C8,C22,C23,C45,C46, 100n POLY. cap.
C48,C49,C51,→,C59
C4
220p CER. cap.
C5
100u Electrolytic
C6,C26
47u Elec. cap. 25V
C7,C27,C28,C29,C47
10n POLY. cap.
C9,C21,C62
56p cer. cap. NP0
C10,C19
22p cer. cap. NP0
C11,C16,C20,C60
120p cer. cap. NP0
C12,C18
6p8 cer. cap. NP0
C13,C61
4p7 cer. cap. NP0
C14,C17
68p cer. cap. NP0
C15
5p6 cer. cap. NP0
C25,C24
1u Elec. cap. 25V
C30,C31,C32
4n7 POLY
C33,C42,C43
10u Elec. cap. 25V
C35,→,C41,C44
3n3 POLY. cap.
C50
12p cer. cap. NP0
C63
100p CER
C64
27p
C65
56p
C66
470n POLY
C67,C68
1p CER
D1,D2
1N4148 DIODE
FIS1,FIS2,FIS3,FIS4
FIS 3.5
F1,F2
EMI EMI filters
IC1
CA3189 I.C.
JP1,JP2,JP3,JP7,→,JP11 JP JUMPER X2
JP5,JP4
JP JUMPER X3
JP6,JP12
JP
J1
SMB CS
J3,J2
CONN14 14AP.
J4
XLR XLR male
L3
22uH axial
L4
1Mh AXIAL IND.
Q1
BC547 trans. NPN
R1
22K RES 1/4W
R4
47K RES 1/4W
R5
20K TRIM MG RV
R6,R68
8K2 RES 1/4W
R7,R14
1K2 RES 1/4W
R8
120R RES 1/4W
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
56 /78
DB
ITEM
QUANTITY
ELETTRONICA TELECOMUNICAZIONI S.p.A.
REFERENCE
PART
_______________________________________________________________________________________________
42
43
44
45
1
1
2
7
46
47
48
49
50
51
1
1
1
1
1
9
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
1
3
1
1
4
1
1
1
2
1
1
2
3
2
2
1
1
2
1
1
1
1
3
1
1
1
4
1
7
R9
R10
R11,R66
R12,R16,R18,R44,R46
R74,R75
R15
R17
R19
R21
R22
R23,R24,R29,R30,R35,
R36,R42,R51,R54
R25
R26,R32,R38
R27
R28
R31,R37,R63,R72
R33
R34
R39
R40,R41
R43
R45
R47,R48
R49,R55,R58
R50,R59
R52,R60
R53
R56
R57,R61
R62
R64
R65
R67
R69,R70,R76
R71
R73
TP1
T1,T2,T3,T4
T5
U1,U2,U3,U4,U5,U6,U7
330R RES 1/4W
4K7 RES 1/4W
56R RES 1/4W
10K RES 1/4W
5K62 RES 1/4W
15K RES 1/4W
47K TRIM MG RV
3K57 RES 1/4W 1%
536R RES 1/4W 1%
3K01 RES 1/4W 1%
3K3 RES 1/4W
2K TRIM MG RV
4K64 RES 1/4W 1%
2K74 RES 1/4W 1%
2K2 RES 1/4W
4K02 RES 1/4W 1%
1K91 RES 1/4W 1%
2K61 RES 1/4W 1%
301K RES 1/4W 1%
1M RES 1/4W 1%
100K RES 1/4W
10K RES 1/4 1%
5K62 RES 1/4W 1%
4K87 RES 1/4W 1%
27R RES 1/4W 1%
1K2 RES 1/4W 1%
1K78 RES 1/4W 1%
4M7 RES 1/4W 1%
50K TRIM MG RV
50K TRIM MG P
47R RES 1/4W
82R RES 1/4W
1K RES 1/4W
13K RES 1/4W
10K RES 1/4W
TP TEST POINT
Style 5R Inductance
TOKO Inductance
TL082 OP. AMP.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
57 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
12. DEMODULATOR STAGE
Fig. 12.1 - DEMODULATOR STAGE ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
58 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 12.2 - DEMODULATOR STAGE COMPONENT LAYOUT (DB 9601-005)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
59 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
12.1 DEMODULATOR STAGE PARTS LIST
ITEM
QUANTITY REFERENCE
PART
_______________________________________________________________________________________________
1
2
3
4
5
6
7
8
9
1
1
1
1
2
1
4
2
16
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
2
1
4
1
2
4
1
3
1
3
3
1
1
1
2
3
1
12
29
30
31
32
33
34
35
36
37
38
6
6
3
2
3
1
1
1
1
1
C1
C2
C3
C4
C5,C43
C6
C7,C11,C25,C33
C8,C24
C9,C12,C13,C14,C18,C22,
C23,C26,C27,C28,C29,C34,
C37,C38,C39,C42
C10
C15,C17
C16
C19,C35,C40,C44
C31
D1,D2
J1,J2,J4,J5
J3
L1,L6,L7
L2
L3,L4,L5
L8,L9,L10
L11
Q1
Q2
Q3,Q5
Q4,Q7,Q8
Q6
R1,R3,R4,R6,R11,R13,R14,
R16,R17,R19,R27,R28
R2,R5,R12,R15,R18,R26
R7,R21,R25,R34,R37,R41
R8,R20,R42
R9,R10
R22,R24,R36
R29
R30
R31
R32
R33
1n CER. cap. SMD
Arancio VARIABLE cap. SMD
22pF CER. cap. SMD
22p CER. cap. SMD
10n CER. cap. SMD
10u Electrolytic cap. SMD
10u Electrolytic cap. SMD
10nF CER. cap. SMD
1n CER. cap. SMD
10u Electrolytic cap. SMD
33p CER. cap. SMD
56p CER. cap. SMD
100n CER. cap. SMD
10uF Electrolytic cap. SMD
HP2811 diode
SMB connector
DB9 9 poles connector
0.1uH inductor SMD
0.22uH inductor SMD
1uH inductor SMD
47uH inductor SMD
0.47uH inductor SMD
BC547 NPN transistor
U310 FET transistor
MSA 0104 Micr integ amp
INA10386 Micr integ amp
MSA 1104 Micr integ amp
270R res SMD
18R res SMD
470R res SMD
390R res SMD
1K res SMD
27R res SMD
56R res SMD
1K5 res SMD
560R res SMD
75R res SMD
100K res SMD
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
60 /78
DB
ITEM
QUANTITY
ELETTRONICA TELECOMUNICAZIONI S.p.A.
REFERENCE
PART
_______________________________________________________________________________________________
39
40
41
42
43
44
45
46
47
1
1
1
1
1
1
1
1
1
R35
R38
R39
R40
R43
U1
U3
U4
U5
100R res SMD
27K RES 1/8W
1K5 RES 1/8W
10K res SMD
390 res SMD
SL1454 I.C.
SAF70MB Integ I.F. filt
78L05 Voltage reg.
RMS230 Mixer
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
61 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
13. RX AMPLIFIER SECTION
13.1 GENERAL DESCRIPTION
DB 9606-019 Front-end board is composed by two equal amplifier stage.
It has typical gains’ of 40 dB (band center).
The technology transistor utilized is INA10386.
Fig. 13.3 - RX AMPLIFIER ELECTRICAL DIAGRAM (DB 9606-019)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
62 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 13.1 - RX AMPLIFIER COMPONENT LAYOUT (DB 9606-019)
13.2 RX AMPLIFIER PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________________
1
2
3
4
5
6
7
8
9
10
11
2
J1,J2
R1,R3,R8,R10
R2,R9
R4,R6
R5,R7
C1,C5,C6,C7
C3,C4,C8
C2
C9
L1,L2
U1,U2
SMA conn.
270R chip
18R chip
470R chip
390R chip
100p HQ
10n BQ
10u elect.
560p
0.1µH
INA10386 Trans.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
63 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
14. TX /RX POWER SUPPLY BOARDS
Fig. 14.1 - MMT - DMT PWR SUPPLY ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
64 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 14.2 - MMT - DMT PWR SUPPLY COMPONENT LAYOUT (AL8GHZ)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
65 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
14.1 MMT - DMT PWR SUPPLY PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________________
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
3
2
3
1
5
3
3
2
2
4
3
1
1
1
1
1
1
3
1
4
2
1
1
1
1
C1,C10,C20
C2,C7
C4,C5,C11
C8
C12,C13,C14,C18,C19
C15,C16,C17
D2,D3,D4
D5,D6
D7,D8
D9,D10,D11,D12
L1,L2,L3
L4
RV1
S1
U1
U2
F1
J3,J4,J5
J6
J7,J8,J9,J12
R1,R2
R3
R4
R6
R7
4700u
100n
10u
1000u
1n
10n
Red
KBL08
1N4007
6A6
VK200
10u
275V
115/230V
LM317
UA7915
5x20mm
Phoenix
Phoenix
Terminal
1K2
390R
8K2
1K
220R
Elett.
Pol.
Elett.
Cer.
Cer.
Led
Bridge diode
Diode
Diode
Ind.
Axial ind.
Varist.
Change volt.
Stab. int.
Stab. int.
Fus.
Con. 3p
Con. 4p
2p
1/4W 5%
1/4W 5%
1/4W 5%
Var.Trimm.
1/4W 5%
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
66 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 14.3 - HMT - HMR POWER SUPPLY ELECTRICAL SCHEMATIC
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
67 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 14.4 - HMT - HMR POWER SUPPLY COMPONENT LAYOUT (DB 9602-011)
14.2 HMT - HMR POWER SUPPLY PARTS LIST
ITEM
QUANTITY
REFERENCE
PART
_______________________________________________________________________________________________
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
4
3
3
1
1
3
4
4
1
1
1
1
1
1
1
1
1
1
1
1
C1,C14,C15,C16
C2,C10,C17
C3,C11,C18
C4
C5
C6,C9,C12
C7,C8,C13,C19
L1,L3,L4,L6
L2
L5
D1
Q1
U1
CN1
R1
R2
R3
R4
R5
R6
220u Elett. 25V
100n Mult.
10n Cer.
1n Cer.
100p Cer.
10u Elett. 25V
100n Pol.
VK200
270u Tor.
100u
1N5819 Diode
BD140 Trans.
UA78S40
AMP Conn. 4
0R47 2W 5%
100R 1/2W 5%
270R 1/2W 5%
15K 1/4W 5%
1K2 1/4W 5%
1K Var.trimm.
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
68 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
15. TX AND RX TECHNICAL SPECIFICATIONS
Overall IF/IF specifications
IF standard frequency .................................................................................................. 70 MHz
IF standard group delay (IF ± 8 MHz) ............................................................................ ≤ 3 ns
Overall BB/BB specifications (-43 dBm at receiver input)
BB amplitude/frequency response (5 Hz to 9.1 MHz) ................................ edsgd within 0.9 dB
Video amplitude/frequency response (5 Hz to 5 MHz) ........................................ within 0.5 dB
Group delay in video band (5 Hz to 5 MHz) .......................................................... within 20 ns
Differential gain .............................................................................................................. ≤ 2 %
Differential phase............................................................................................................... ≤ 2°
Audio channels frequency response (30 Hz to 15 kHz)......................................... within 0.5 dB
Audio channels THD (1 kHz, 0 dBm) ...........................................................................≤ 0.3 %
Transmitter characteristics
Modulation............................................................................................................ CCIR 405/1
Frequency deviation................................................................................................ 20 MHz pp
Output power ......................................................... 2W for HMT2 /2G or 5W for HMT5 /2G
IF+ 15 VDC output connector .................................................................................... N female
BB/Video input level ................................................................................ 1 Vpp (75 Ω unbal.)
Video input connector ...................................................................................................... BNC
Video preemphasis (bypassable).................................................................... C.C.I.R. 625 lines
Audio input level (∆f = 75 kHz peak.)..................................-3 to +12 dBm (600 Ω bal./unbal.)
Audio input connector. .......................................................................................... XLR female
Audio pre-emphasis (bypassable) ......................................................................... 50 µS, 75 µS
Audio subcarrier frequencies...........................................................................7500, 8065 MHz
Power supply.............................................................................AC 110/220 ± 15% , 50/60 Hz
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
69 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Receiver characteristics
RF range.............................................................................................. -90 to -15 dBm (50 Ω)
Video de-emphasis (by-passable) ................................................................. C.C.I.R. 625 lines
BB/Video output level ........................................................................................1 Vpp (75 Ω)
Video output connector ................................................................................................... BNC
Audio output level (∆f = 75 kHz peak) ............................... -3 to +12 dBm (600Ω bal./unbal.)
Audio de-emphasis (bypassable) ......................................................................... 50 µS, 75 µS
Power supply ............................................................................AC 110/220 ± 15% , 50/60 Hz
Transmitter/receiver general data
Outdoor operating temperature range ................................................................ -20 to +50 °C
Outdoor operating humidity range ................................................................................ ≤ 95 %
TX – RX Dimensions (W x L x H)............................................................ 305 x 400 x 140 mm
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
70 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
16. INSTALLATION
16.1 INSTALLING MMT-HMT /P
For installing the MMT-HMT /P transmitter, perform the following steps.
1) Power the device with the cable supplied.
2) Remove the first panel.
3) On the second panel connect the filter to the feeder
4) Power on the equpment.
The PWR led on front panel should light up.
The LOCK led on front panel should light down.
5) Connect a video signal, with BNC connector video input.
It may be necessary to set the modulation depth in correspondence of video input signal level,
then adjust a panel trimmer (Trimmer R41). The value we suggest is 20 MHz peak to peak.
The Led Bar on the front panel furnishes the modulation level (kHz or MHz). To select the signal
that must be measured (Video, Audio1, Audio2) press the button; when the Video signal is
selected the led Video lights on.
6) Connect an audio signal, with XLR connector to subcarrier 1, 2 input.
It may be necessary to set the modulation depth in correspondence of video input signal level,
then adjust panel trimmers (R12 trimmer Fig. 4.5). The value we suggest is 70 kHz peak.
The Led Bar on the front panel furnishes the modulation level (kHz or MHz). To select the signal
that must be measured (Video, Audio1, Audio2) press the button; when the desired signal is
selected the led Audio1 or Audio 2 on.
For pre-emphases de-insertion disconnect JP5 and JP6 jumper for 75µs (Fig. 4.5).
It can be necessary to adjust the relative level between the subcarriers and the Video signal, then
adjust R37,R38 trimmers for subcarriers levels and R30 trimmer for Video level (see
Fig. 3.7); in case the regulation of trimmer R41 it is not enough adjust trimmer R30 (see Fig. 3.7)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
71 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 16.1 - MMT-HMT /P INSTALLATION
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
72 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
16.2 INSTALLING DMT-HMR /P
For installing DMT-HMR /P receiver, perform the following steps.
1) Power the device with the cable supplied.
2) Remove the first panel.
3) On the second panel connect the filter to the feeder.
Warning :
RF input level of HMR must not exceed -30dBm
4) Power on the equipment
The ON led on front panel should light up.
The PLL LOCK led on front panel should light down.
5) Connect a video signal receiver with BNC connector in Video output.
If it is necessary, adjust panel trimmer (R11 trimmer
Fig. 10.7) for signal level setting.
The Led Bar on the front panel furnishes the signal level (Volts). To select the signal level (Video,
Audio1, Audio2) or the carrier level (SIGNAL) that must be measured, press the button; when
the desired signal is selected its led lights on.
6) Connect an audio signal receiver to Subcarrier 1 or 2 output with XLR connector.
It can be necessary the signal level settings, then adjust panel trimmers (Trimmer R64
Fig. 11.4).
The Led Bar on front panel furnishes the signal level (Volts). To select the signal (Video, Audio1,
Audio2 signal) that must be measured push the button; when the desired signal is selected its led
is light on.
For de-emphases de-insertion connect JP6 jumper for 50 µs (see
Fig. 11.4).
For de-emphases de-insertion connect JP6 and JP12 jumper for 75 µs (see
Fig. 11.4).
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
73 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Fig. 16.2 - DMT-HMR /P INSTALLATION
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
74 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
16.3 CHANNEL SETTING
The channel settings is factory made under user’s indication.
The transmitter channel settings is realized by means of jumpers located on VCO board .
See the following indications for jumper settings:
1 - Each jumper has a rising weight from left to right (0.125 MHz, 0.250 MHz , ..) (
Fig. 11.4).
2- Leave jumpers open so that the sum of the weights is the channel frequency.
EXAMPLE: Setting a channel with carrier at 10500 MHz.
The up-converter and the down-converter make a 9300 MHz frequency transposition therefore it is
necessary an IF of 1200 MHz.
Transmitter : for 1200 MHz carrier the weights to set off (leave jumper open) in the VCO board
are:
- 1024 MHz
- 128 MHz
- 32 MHz
- 16 MHz
Fig. 16.3 - TRANSMITTER JUMPERS (VCO BOARD ON MMT)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
75 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
Receiver: for 1200 carrier it is necessary to subtract the 70 MHz reference frequency obtaining
1130 MHz ;
the weights to set in the local oscillator (L.O.) board are:
- 1024 MHz
- 64 MHz
- 32 MHz
- 8 MHz
- 2 MHz
Fig. 16.4 - RECEIVER JUMPERS (L.O. BOARD ON DMT)
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
76 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
17. APPENDIX A
17.1 XLR AUDIO CONNECTORS PINOUTS FOR MMT
The pattern below shows how to connect the cables of the audio signal to the male XLR connectors
for balanced or unbalanced signal.
MALE XLR
XLR CONNECTOR PIN
1
2
3
BALANCED SIGNAL
UNBALANCED SIGNAL
ground
"+"
"–"
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
ground
ground
signal
77 /78
DB
ELETTRONICA TELECOMUNICAZIONI S.p.A.
17.2 XLR AUDIO CONNECTORS PINOUTS FOR DMT
The pattern below shows how to connect the cables of the audio signal to the female XLR
connectors for balanced or unbalanced signal.
FEMALE XLR
XLR CONNECTOR PIN
1
2
3
BALANCED SIGNAL
UNBALANCED SIGNAL
ground
" +"
"–"
MMT-HMT /P DMT-HMR /P - USER’S MANUAL
ground
not connected
signal
78 /78
Download PDF