SM30 Series 30 mm Barrel Sensor

SM30 Series 30 mm Barrel Sensor
Opposed-Mode Infrared Photoelectric Sensors for Especially Demanding Applications
Features
• Stainless steel or plastic barrel models
• Very high excess gain; 200 m (700') sensing range; 880 nm Infrared LED
• Positive sealing eliminates even capillary leakage; lens is quad-ring sealed; exceeds
NEMA 6P (IP67) ratings – ideal for equipment wash-down environments
• EZ-BEAM® technology provides reliable sensing without the need for adjustment
• Modulation frequency “A” is standard; frequencies “B” and “C” also available for
preventing crosstalk in multiple-sensor applications (emitter and opposed receiver
frequencies must match)
• AC- and DC-operated receiver models available; emitters feature Universal voltage
• Range for all models: 200 m (700'). See page 3 for performance curves.
Models
Modulation Frequency*
A
B
C
Housing
Cable**
Supply
Power
Output Type
Universal:
12 to 240V ac,
10 to 30V dc
–
10 to 30V dc
Bi-Modal™
NPN or PNP
Emitter Models
SMA30PEL
SMA30PELB
SMA30PELC
SMA30PELQD
SMA30PELQDB
SMA30PELQDC
SMA30SEL
SMA30SELB
SMA30SELC
SMA30SELQD
SMA30SELQDB
SMA30SELQDC
SM30PRL
SM30PRLB
SM30PRLC
SM30PRLQD
SM30PRLQDB
SM30PRLQDC
SM30SRL
SM30SRLB
SM30SRLC
SM30SRLQD
SM30SRLQDB
SM30SRLQDC
SM2A30PRL
SM2A30PRLB
SM2A30PRLC
SM2A30PRLQD
SM2A30PRLQDB
SM2A30PRLQDC
SM2A30SRL
SM2A30SRLB
SM2A30SRLC
SM2A30SRLQD
SM2A30SRLQDB
SM2A30SRLQDC
SM2A30PRLNC
SM2A30PRLNCB
SM2A30PRLNCC
SM2A30PRLNCQD
SM2A30PRLNCQDB
SM2A30PRLNCQDC
SM2A30SRLNC
SM2A30SRLNCB
SM2A30SRLNCC
SM2A30SRLNCQD
SM2A30SRLNCQDB
SM2A30SRLNCQDC
Plastic
Stainless
Steel
2 m (6.5') 2-wire Cable
3-pin Mini-style QD†
2 m (6.5') 3-wire Cable
3-pin Mini-style QD†
DC Receivers
Plastic
Stainless
Steel
2 m (6.5') 4-wire Cable
4-pin Mini-style QD
2 m (6.5') 4-wire Cable
4-pin Mini-style QD
AC Receivers
Plastic
Stainless
Steel
Plastic
Stainless
Steel
2 m (6.5') 2-wire Cable
SPST
Solid-state,
L.O.
3-pin Mini-style QD†
2 m (6.5') 3-wire Cable
3-pin Mini-style QD†
2 m (6.5') 2-wire Cable
24 to
240V ac
SPST
Solid-state,
D.O.
3-pin Mini-style QD†
2 m (6.5') 3-wire Cable
3-pin Mini-style QD†
* Any emitter and receiver shown here can be used together, if they have the same modulation frequency.
** Standard 2 m (6.5') cable and integral QD models are listed. A model with a QD connector requires a mating cable; see page 4.
9 m (30') cable: add suffix “W/30” following the Frequency suffix of any cable model (e.g., SM30PRLBW/30).
† AC models with QD require SM30CC model cables; see page 4.
Important: See Safety Warning on Back Page
Printed in USA
07/05
P/N 03541 rev. D
SM30 Series 30 mm Sensors – for Especially Demanding Applications
Specifications
Supply Voltage and Current
Emitters: 12 to 240V ac (50/60 Hz) or 10-30V dc at 20 mA, 10% maximum ripple
DC Receivers: 10 to 30V dc at 10 mA maximum (exclusive of load); 10% maximum ripple
AC Receivers: 24 to 240V ac (50/60 Hz)
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
DC Receivers: Bi-Modal™ output (PNP sourcing or NPN sinking). Selection of light/dark operate and
sourcing or sinking configuration dependent on hookup.
AC Receivers: SPST solid-state switch; light operate (LO) or dark operate (DO) dependent on model.
Output Rating
DC Receivers: 250 mA continuous
Output saturation voltage (PNP & NPN configuration) < 1 volt at 10 mA and < 2 volts at 250 mA
Off-state leakage current < 10 microamps
AC Receivers: Maximum steady-state load capability is 500 mA
Inrush capability: 10 amps for 1 second (non-repeating)
Off-state leakage: current < 1.7 mA rms
On-state voltage drop: < 3.5 volts rms across a 500 mA load; < 5 volts rms across a 15 mA load
Output Protection Circuitry
Outputs of dc receivers are short circuit protected
Output Response Time
10 milliseconds on/off
Repeatability
“A” frequency models: 1 ms
“B” frequency models: 1.5 ms
“C” frequency models: 2.3 ms
Indicators
Internal red LED, visible through the lens or from side of the sensor.
Emitters: Red “Power ON” indicator LED
DC Receivers: Lights whenever receiver sees its modulated light source
AC Receivers: Lights whenever receiver’s output is conducting
Construction
Fully epoxy-encapsulated tubular threaded housing, positive sealed at both ends, quad-ring sealed acrylic lens.
Plastic models: 30 mm diameter thermoplastic polyester housing and jam nuts.
Stainless Steel models: 30 mm diameter 303 stainless steel housing and jam nuts.
Environmental Rating
Exceeds NEMA 6P and IEC IP67 standards
Connections
PVC-jacketed 2 m or 9 m cables or Mini-style quick-disconnect (QD) fitting are available. QD cables are
ordered separately. See page 4.
Operating Conditions
Temperature: -40° to +70° C (-40° to +158° F)
Relative humidity: 90% at 50° C (non-condensing)
Certifications
Dimensions
Cabled Models
QD Models
Jam Nuts
(2 Provided)
Jam Nuts
(2 Provided)
Alignment
Indicator (Receivers)
Alignment
Indicator (Receivers)
M30 x 1.5
Thread
M30 x 1.5
Thread
102 mm
(4.0")
2
P/N 03541 rev. D
114 mm
(4.5")
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SM30 Series 30 mm Sensors – for Especially Demanding Applications
Performance Curves
Excess Gain Curve
Beam Pattern
100000
SM30 Series
Opposed Mode
SM30 Series
10000
E
X
C
E
S
S
G
A
I
N
Opposed Mode
1500 mm
60 in
1000 mm
40 in
500 mm
20 in
1000
0
100
0
500 mm
20 in
1000 mm
40 in
1500 mm
60 in
10
0
45 m
150 ft
90 m
300 ft
135 m
450 ft
180 m
600 ft
225 m
750 ft
DISTANCE
1
1m
3.3 ft
10 m
33 ft
100 m
330 ft
DISTANCE
1000 m
3300 ft
Hookups
sm30epq.eps
sm30es.eps
Emitters – Cabled
��
AC Receivers – Cabled
�����
������������
����������
��
ac-sm30rs.eps
Emitters – QD
�����
���
������������
����������
ac-sm30rqs.eps
AC Receivers – QD
�����
��
��
����
����������
�����
���
���
NOTE:
AC emitters are not polarity-sensitive when powered by dc voltage.
������������������������������������������
For QD emitters, use SM30CC model cables listed on page 4 in
�����������������������������������������������
order to match cable colors.
��������������������������������������
����������
����
���
������������������������������������������ ������������������������������������������
�����������������������������������������������
�����������������������������������������������
��������������������������������������
��������������������������������������
*Connect green wire to earth ground whenever a stainless steel model is powered by ac voltage. (Cabled plastic models have no green wire.)
DC Receivers – NPN
Light Operate
sm30rnlq.eps
DC Receivers – PNP
Dark Operate
Light Operate
sm30rndq.eps
wh
wh
wh
bu
bu
bu
–
10-30V dc
+
bn
bk
bk
Load
–
10-30V dc
+
bn
Load
Dark Operate
sm30rplq.eps
wh
+
10-30V dc
–
bn
bk
sm30rpdq.eps
Load
bu
+
10-30V dc
–
bn
bk
Load
NOTE: Where QD hookups only are shown, cabled model hookups are functionally identical.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 03541 rev. D
3
SM30 Series 30 mm Sensors – for Especially Demanding Applications
Quick-Disconnect (QD) Cables
Style
Model
Length
3-pin Mini-Style
SM30CC-306
SM30CC-312
2 m (6.5')
4 m (12')
Connector
Use with
Emitters and
AC receivers
4-pin Mini-Style
2 m (6.5')
4 m (12')
9 m (30')
�����
���������
Straight
MBCC-406
MBCC-412
MBCC-430
Pinout
�����������
�����
�����������
���������
�����
DC receivers
�����
����
Apertures
Model
APG30S
Description
Kit includes: a thread-on stainless steel housing, a flat
glass lens, two quad-ring seals, plus 3 round and 3
slotted aperture disks
Mounting Brackets
!
SMB30A
• 30 mm, 12-gauge, stainless steel, right-angle bracket with a curved mounting slot for versatile orientation
• Clearance for M6 (1/4") hardware
SMB30C
• 30 mm split clamp bracket
• Black reinforced thermoplastic polyester
• Includes stainless steel mounting hardware
SMB30MM
• 30 mm, 12-gauge, stainless steel, right-angle bracket with curved mounting slots for versatile orientation
• Clearance for M6 (1/4") hardware
SMB30SC
• 30 mm swivel bracket
• Black reinforced thermoplastic polyester
• Includes stainless steel mounting and swivel locking hardware
WARNING . . . Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A
sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner
Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of
Banner products. This warranty is in lieu of any other warranty either expressed or implied.
P/N 03541 rev. D
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
Download PDF