User Manual Back-UPS® BE350G Series
Safety
Connect Equipment
This unit is intended for indoor use only.
Do not operate this unit in direct sunlight, in
contact with fluids, or where there is
excessive dust or humidity.
Battery Backup +
Connect the Back-UPS power cord directly to
a wall outlet. Do not use a surge protector or
an extension cord.
Back-UPS
Specifications
Output
Protection
and
Filtering
Battery
Physical
120 Vac Nominal
Frequency
60 Hz + 3
Brownout Transfers
92 Vac Typical
Over-voltage Transfer
139 Vac Typical
UPS Capacity
(3 outlets)
350 VA, 200 W
Battery backup outlets provide protection to connected equipment when the
Back-UPS is turned on and connected to utility power.
Total Amperage
(6 outlets)
8 A (including UPS output)
Battery backup outlets receive power from the Back-UPS for a limited period of time
when a power outage, or brownout condition occurs.
Voltage - On Battery
115 Vac ± 8%
Frequency - On Battery
60 Hz + 1
Transfer Time
6 ms Typical, 10 ms maximum
AC Surge Protection
Full time, 340 Joules
EMI/RFI Filter
Full time
AC Input
Resettable circuit breaker
Type
Sealed, maintenance-free, lead acid
Replacement battery cartridge RBC35
Average Life
3 - 5 years depending on the number
of discharge cycles and environmental
temperature
Net Weight
9 lb (4 kg)
Dimensions
Length x Width x Height
11 in x 6 in x 3 in
29 cm x 16 cm x 9 cm
Operating Temperature
32º F to 104º F (0º C to 40º C)
Storage Temperature
5º F to 113º F (–15º C to 45º C)
Battery Backup + Surge Protection Outlets
Battery backup outlets provide protection from power surges or spikes.
Connect a computer, monitor and other peripheral devices to the outlets.
Surge Protection Outlets
Surge protection outlets provide protection to connected equipment when the
Back-UPS is connected to utility power, and is switched on or off.
Surge protection outlets provide protection from power surges or spikes.
Connect a printer, scanner or other peripheral devices that do not need to remain on
during power outages, or utility problems to the surge protection outlets.
Connect Network
Building
Wiring Fault
Circuit
Breaker
Network
Out
Network
In
Push to
Reset
Operating Relative Humidity 0 to 95% non-condensing humidity
Operating Elevation
CAUTION-Refer to bottom
of unit for safety markings.
0 to 10,000 ft (0 to 3000 m)
This device complies with part 68 and part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device
EMC
may not cause harmful interference, and (2) This device must accept
Compliance
any interference received, including interference that may cause
undesired operation.
Connect the Battery
bu208a
Input
Surge Protection
bu206a
Voltage
Surge Protection
The Back-UPS protects equipment connected to a 10/100 Base-T ethernet, from
power surges when connected through the Back-UPS coaxial connectors.
Turn On the Back-UPS
Press the POWER ON button located on the top of the Back-UPS. The Power On/
Replace Battery LED will illuminate and a single short beep will be audible to
indicate that the Back-UPS is providing protection for connected equipment.
The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!
Connect the Battery” label that covers the outlets. Prior to connecting any equipment
to the unit, connect the battery cable to the unused battery terminal. It is normal for
small sparks to be seen when the battery cable is connected to the battery terminal.
The Back-UPS battery charges fully during the first 16 hours while connected to
utility power. The Back-UPS battery will charge while the Back-UPS is switched on
or off and is connected to utility power. Do not expect full battery run capability
during the initial charge time.
 Press the battery compartment cover
release tab located on the rear side of the
unit. Slide the battery cover off.
If the red Building Wiring Fault LED located on the side of the Back-UPS
illuminates, do not operate the Back-UPS. Have a qualified electrician correct the
building wiring fault.
bu064a
Voltage Sensitivity Adjustment (optional)
The Back-UPS detects and reacts to line voltage distortions by transferring to battery
backup power to protect connected equipment. In situations where either the BackUPS or the connected equipment is too sensitive for the input voltage level it is
necessary to adjust the transfer voltage.
 Connect the battery cable securely to
the battery terminal.
bu065a
1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode,
no indicators will be illuminated.
2. Press and hold the ON/OFF button for 10 seconds. The OnLine LED will
illuminate alternately green-amber-red, to indicate that the Back-UPS is in
Program mode.
3. The Power On/Replace Battery LED will flash either green, amber, or red to
indicate the current sensitivity level. Refer to the table for an explanation of the
transfer voltage sensitivity levels.
 Reinstall the battery compartment
cover. Be sure that the release tab locks
into place.
bu066a
4. To select LOW sensitivity, press and hold the ON/OFF button until the LED
flashes green.
5. To select MEDIUM sensitivity, press and hold the ON/OFF button until the LED
flashes red.
6. To select HIGH sensitivity, press and hold the ON/OFF button until the LED
flashes amber.
Wall Mount Installation
•
•
•
Horizontal installation, use 2 screws 5.0" (127 mm) apart.
Vertical installation, use 2 screws 4.3" (110.4 mm) apart.
Allow 5/16" (8 mm), of the screw to protrude from the wall.
7. To exit Program mode wait five seconds and all LED indicators will extinguish.
Program mode is no longer active.
LED Sensitivity Input Voltage Range
Flashes Setting
(Utility Operation)
Recommended Use
Green
LOW
88 Vac to 142 Vac
Use this setting with equipment that
is less sensitive to fluctuations in
voltage or waveform distortions.
Red
MEDIUM
92 Vac to 139 Vac
Factory default setting. Use this
setting under normal conditions.
Amber
HIGH
96 Vac to 136 Vac
Use this setting when connected
equipment is sensitive to voltage
and waveform fluctuations.
Status Indicators
Status
LED Indicator
Audible Indicator On
Power On
The Back-UPS is supplying utility power to connected
equipment.
The green LED illuminates.
On Battery
Back-UPS supplying battery power to battery backup outlets.
The green LED illuminates.The LED Back-UPS beeps 4 times
is not illuminated during the beeps. every 30 seconds.
None
Audible Indicator Terminates
N/A
Beeping stops when utility power is restored or
the Back-UPS is turned off.
Low Battery warning
The green LED illuminates with
The Back-UPS is supplying battery power to the battery backup
rapid green flashes.
outlets and the battery is near a total discharge state.
The Back-UPS emits rapid Beeping stops when utility power is restored or
beeping, every 1/2 second. the Back-UPS is turned off.
Replace Battery
Constant tone
• Replace Battery LED flashes.
• Replace Battery and Power On
LEDs flash alternately.
• The battery is disconnected.
• The battery needs to be charged, or replaced.
Overload Shutdown
While on battery power an overload condition has occurred in
one or more of the battery backup outlets while the Back-UPS
is operating on battery power.
Sleep Mode
While on battery power the battery is completely discharged.
The Back-UPS will “awaken” once utility power is restored.
Building Wiring Fault
The building wiring presents a shock hazard that must be
corrected by a qualified electrical.
None
Back-UPS is turned off.
The Back-UPS beeps once • Utility power is restored
every four seconds.
• If utility power is not restored within 32 seconds
• The Back-UPS is turned off
None
Building Wiring Fault LED
illuminates red
Solution
None
The Back-UPS is unplugged from the wall outlet
or is plugged into an improperly wired outlet.
Use only approved APC replacement battery cartridges.
Deliver used batteries to a battery replacement facility in the packaging provided by
APC with the replacement battery cartridge.
The Back-UPS will not turn on
The Back-UPS has not been turned
on.
Press the POWER ON button.
The Back-UPS is not connected to
utility power, there is no utility
power available at the wall outlet, or
the utility power is experiencing a
brownout or over voltage condition.
Make sure the power cord is securely connected
to the wall outlet, and that there is utility power
available at the wall outlet.Where applicable,
check that the wall outlet is switched on.
The battery is not connected.
Connect the battery. Refer to “Connect the
Battery” on page 1 of this manual.
In the event that the Back-UPS receives no utility
power and the battery is connected, a cold-start
can be initiated. Press and hold the Power On
button until the Back-UPS emits two beeps.
The Back-UPS is on, the Replace Battery LED flashes and the unit emits a
constant tone
Refer to the “Connect the Battery” on page 1.
Connected equipment loses power
A Back-UPS overload condition has Remove all nonessential equipment connected to
occurred.
the outlets. One at a time reconnect equipment to
the Back-UPS.
The Back-UPS battery is completely Connect the Back-UPS to utility power and allow
discharged.
the battery to recharge for eight hours.
PowerChute software has performed This is normal Back-UPS operation.
a shutdown due to a power failure.
Connected equipment does not
accept the step-approximated sine
waveform from the Back-UPS.
The output waveform is intended for computers
and peripheral devices. It is not intended for use
with motor driven equipment.
The Back-UPS may require service.
Contact APC Technical Support for more in
depth troubleshooting.
The Power On LED is illuminated and the Back-UPS beeps 4 times every
30 seconds
The Back-UPS is operating normally on battery
power. At this point the user should save all open
files, and shutdown the computer. When utility
power is restored the battery will recharge.
The Power On LED flashes once every second while the Back-UPS beeps
once every second
The Back-UPS battery has
approximately two minutes of
remaining runtime.
Constant tone
Replace Battery
Problem and Possible Cause
The Back-UPS is operating on
battery power.
Back-UPS is turned off.
The beeping stops when:
Troubleshooting
The battery is disconnected.
Constant tone
The Back-UPS battery is near a total discharge
state. At this point the user should save all open
files, and shutdown the computer. When utility
power is restored the battery will recharge.
To order replacement battery cartridges contact APC through the Web site
www.apc.com
Warranty
The standard warranty is 3 years in the USA and Canada, 2 years in all other regions
from the date of purchase. APC standard procedure is to replace the original unit with
a factory reconditioned unit. Customers who must have the original unit back due to
assigned asset tags and set depreciation schedules must declare such a need at first
contact with APC Technical Support. APC will ship the replacement unit once the
defective unit is received by the repair department or cross-ship upon the provision of
a valid credit card number. The customer pays for shipping to APC, and APC pays
ground freight transportation costs back to the customer.
Service
If the unit requires service, do not return it to the dealer. Follow these steps:
1. Review the Troubleshooting section of the manual to eliminate common
problems.
2. If the problem persists, contact APC Customer Support.
a. Note the model number and serial number and the date of purchase. The
model and serial numbers are located on the rear panel of the unit and are
available through the LCD display on select models.
b. Call APC Customer Support and a technician will attempt to solve the
problem over the phone. If this is not possible, the technician will issue a
Returned Material Authorization Number (RMA#).
c. If the unit is under warranty, the repairs are free.
d. Service procedures and returns may vary internationally. Refer to the APC
Web site for country specific instructions.
3. Pack the unit properly to avoid damage in transit. Never use foam beads for
packaging. Damage sustained in transit is not covered under warranty. Always
DISCONNECT THE UPS BATTERY before shipping in compliance with
U.S. Department of Transportation (DOT) and IATA regulations. The battery
may remain in the unit.
4. Write the RMA# provided by Customer Support on the outside of the package.
5. Return the unit by insured, pre-paid carrier to the address provided by Customer
Support.
Contact
APC Web site, www.apc.com
The Building Wiring Fault LED illuminates
The building wiring presents a shock Do not operate the Back-UPS. Call a qualified
hazard that must be corrected by a
electrician to correct the building wiring fault.
qualified electrical.
The Back-UPS has an inadequate battery runtime
The battery is not fully charged.
The battery is near the end of useful
life and should be replaced.
Leave the Back-UPS connected to utility power
for 16 hours while the battery charges to full
capacity.
As a battery ages, the runtime capability
decreases. Contact APC at the Web site
www.apc.com, to order replacement batteries.
The connection from the Back-UPS to the internet is lost during a power
outage
The modem has lost power.
Connect the modem cable into one of the Battery
Backup + Surge Protection outlets.
© 2011 APC by Schneider Electric. APC, the APC logo, Back-UPS and PowerChute are owned by Schneider Electric Industries S.A.S., American Power Conversion
Corporation, or their affiliated companies. All other trademarks are property of their respective owners.
990-3950B
7/2011
Download PDF