G2213D
MIC
PWR
MUTE
SEL
SRC/NAV
Model:G2213D
Thank you for buying this product, please read through these operating instructions,
so you will know how to operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future reference .
CONTENTS
PRECAUTIONS
2
FRONT PANEL
4
SYSTEM MENU
6
REMOTE CONTROL
13
BASIC OPERATION
17
RADIO OPERATION
18
BLUETOOTH OPERATION
20
DVB-T OPERATION
23
DVD/VCD/CD OPERATION
25
SYSTEM SETUP
28
MP3 OPERATION
33
NAVIGATION OPERATION
35
INSTALLATION
37
TROUBLE SHOOTING
39
CABLE CONNECTION
41
ACCESSORIES
41
SPECIFICATION
42
IMPORTANT: Please adjust screen to make the touching effect function best when
you initiate the unit for the first time.
For the details, please refer to the operation at Page 9.
NOTE: Due to the continuous product improvement, specifications and design are
subject to change without prior notice.
1
PRECAUTIONS
1. Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicles electrical system.
2. Be sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect
the left and right channel speaker cables each other or to the vehicle body.
3.Make sure all the connections are completely correct before turning on your unit.
4. When replacing the fuse(s), the replacement must be of the same amperage as shown
on the fuse holder.
5. Do not block vents or radiator panels. Heat may be caused inside and some accident
may be resulted by fire.
6 After completing the installation and beginning to play the unit (including replacing the
battery),please press RESET button on the front panel with pointed object (such as ballpoint pen) to set the unit to initial status.
7.Keep hands, finger, or any other object away from the back of the front panel or gaps of
the base top (shown as picture) when closing or opening to avoid damage or injury.
Replacing the Fuse
Make sure the amperage matches the specified value when replacing the fuses. If the
fuse is blown, check the power connection and replace with a new one. If the same
problem occurs, it would be subjected to the malfunction in-house.In such cases, please
consult the nearest service dealer.
WARNING:
Never use the fuse with the rated amperage more than that supplied to your unit, other wise the unit will be damaged .
2
PRECAUTIONS
F This unit can play the following discs only:
Type of disc
Label on the disc
Recorded material
Size of disc
Sound and moving
pictures
12cm
VCD
Sound and moving
pictures
12cm
CD
Sound only
12cm
MP3
Sound only
12cm
DVD
TM
V I D E O
NOTE: The unit is compatible with VCD1.0/2.0/3.0 version and DVCD disc.
*Do not attempt to modify the unit, modifying the unit may cause an accident.
*Stop the vehicle before carrying out any operation that could interfere with your driving.
*Do not work in extremely high or low temperature. Be sure the temperature inside the
vehicle is between +60 C and -10 C before turning on your unit .
*To enjoy optimum sound and images while playing, handle the discs as follows:
Handle the disc by its edge to keep the disc clean, and do not touch the surface.
Do not use your CDs with paste residue or ink attached.
Do not use CDs with labels or stickers attached, which may leave a sticky residue
while beginning to peel off. (Shown as the picture)
Clean the discs with an optional cleaning cloth. Wipe each disc from the center out.
(Shown as the picture)
3
FRONT PANEL
G2213D
12
PWR
MUTE
SEL
SRC/NAV
MIC
1 2 3 4
5
7
6
8
9 10 11
13
15
4
14
FRONT PANEL
1.AUX IN
Connect the audio cable to the unit then you can enjoy the music.
2. MIC
3. POWER /MUTE
Press the button to turn on the unit and press and hold the button to turn off the unit.
In power on, press to shut off the sound output and press it again to resume previous sound.
4. RESET
5.
/
In radio mode, press and hold to manual seek a station. Press to automatic seek a station.
In playback mode, long press to select fast forward or fast backward. Press to select last
or next track(chapter)
6.SEL +/In radio mode, press this button to start the system setup.
Then press + button to increase the corresponding item level and press - button to
decrease the corresponding item level.
In playback mode, press this button to start setup page.
7.
Press to eject a disc.
Press and hold this button to force ejecting a disc when the system becomes frozen.
accidentally.
8.SRC/NAV
Press the button repeatedly to switch sources.
Press and hold this button to start navigation operation.
9.
Press to open/close the front panel. During opening the front panel, you can press
the button to set the panel angle.
10. IR WINDOW
11. USB SLOT
12. TFT DISPLAY
13. DISC LOADING SLOT
14. SD slot
Insert the SD card, the unit will play the items automatically.
Note:
When the SD card could not eject automatically after pressing, it is suggested to
take it out manually.
5
MENU SYSTEM
The users can perform operation by touching screen directly.
RADIO OPERATION
16 15
13 12
14
1
11
FM1 P6
2
87.50MHz
10
3
4
5
6
7
8
9
1. CURRENT STATUS
2/10. < / >
To switch bands.
3.Station preset button
To display the preset station list
(touch one of the station preset button to recall the radio which stored on the position;
long touch to save the current frequency into the station)
4.AMS
To browse preset stations.
To search and store stations automatically(long touch).
5/6. >> / <<
To seek a station automatically.
7/8.
/
To seek a station manually.
9. RDS
To go to RDS operation
11.BACK
To be back to display the SOURCE screen
12. MUTE
To shut off the audio output and touch again to resume.
13/15. +/To increase or decrease the volume.
14. Volume bar
16. BAND AND PRESET STATION DISPLAY
6
MENU SYSTEM
RDS OPERATION
FM1 P1
1
87.50MHz
3
4
2
5
6
1.AF
ON: To turn on AF function.
OFF: To turn off AF function.
2.TA
ON: To turn on TA function.
OFF: To turn off TA function.
3.ST
ON: To turn on STEREO function.
OFF: To turn on MONO function.
4.LOC
ON: To tune in local area.
OFF: To tune in local and distant area.
5.PTY
To select one of the program types.
6.RADIO
To go to radio operation.
7
MENU SYSTEM
MULTI-- PLAYER OPERATION
In DVD/VCD mode, the touch screen displays as following after tapping at random position.
1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
Fig.1
Fig.2
Fig.3
1.
To start/pause the playback.
2.
To stop playing, touch twice to stop completely.
3/4.
To select previous/next chapter or track.
5/6.
To play in fast rewind or fast forwards mode.
7/14/20.
To select more items.
8.
To play in random order.
9.
To select one of the repeat modes.
10.OSD
To select title elapsed, title remain, chapter elapsed, chapter remain, display off.
11.SUB-T.
To select the subtitle type if the DVD supports.
12.MENU
To display the DVD SETUP screen.
13.TITLE
To display the title menu.
15.ANGLE
To change the DVD viewing angle if the DVD supports.
16. ZOOM
To change the DVD viewing scale if the DVD supports.
17.PBC
To display the PBC menu in VCD mode.
18.P/N
To select PAL , AUTO or NTSC system
19.A-B
To play the selected A-B section.
NOTE: Touch the left middle position twice to display the TITLE MENU selection screen, touch the
right middle position twice to display the ROOT MENU selection screen, touching the right top
position to display the number keyboard.
You can select chapter(track) by press the touchable screen or the RC.
8
Setup Operation
TOUCH ON THE TOP RIGHT POSITION TO ENTER SOURCE INTERFACE.
The unit will return to the previous mode if no operation is performed in 5 seconds.
Touch on SET button on the above fig.. The user can start the system setting.
1. SETUP
Touch on the
SETUP button and the screen will display as following:
Fig.1
Fig.2
TIME MODE
Set the time display mode(12H/24H).
TOUCH SCREEN
To calibrate the touch screen.
RADIO REGION
To select the right region as per the user locates.
Tapping on
button to turn to next page shown as fig.2.
In FIG.2
TIME ADJUSTMENT
To adjust the time by tapping
button;
TIME DISPLAY
ON: To display the time
OFF: To turn off the time display mode.
9
SW CONTROL OPERATION
Tapping on
button to turn to next page shown as fig.3.
Fig.3
Fig.4
SW control
To set 6 short-cut bottons for the steering wheel control.
The screen will display as fig.4 if there is no set for the system.
There are 10 buttons for selection in each item:
POWER, SRC, PREV, NEXT, VOL+,VOL-, MUTE, PAUSE,
and
.
Please refer to the following sequential order to finish the setting:
1. Touch on one of the 6 BLANK columns position on the screen;
2. Press one button on the SW control;
3. The relative information jumps out on the screen;
4. Touch one of the functions as the wanted function for the pointed button on SW control;
Note:
1.The group-setting can be erased by pressing and holding the selected group.
2. If there is already a set item, press the corresponding button on the SW control
and the screen will display: Exist key X.
3. Different buttons on the SW can be defined to the same function. The defined button
can be redefined after erasing the previous function.
10
SW CONTROL INSTALLATION
Before installing the SW control, please make sure all the wires are in good condition.
For installation, please refer to the illustrations below:
GND
SWC1, orange
GND, black
X
Key1
X
In case of connecting to the SWC (steering wheel control):
X
Key2
CAR AUDIO
SWC2, brown
SWC
in case of connecting to the SW remote control:
Key1
GND
Key2
B+
SW remote control
IR
X
SWC(IR), Blue/yellow
CAR AUDIO
GND
Please consult the professional technicians for advice if the unit cannot work as expected.
11
2.Audio
Touch on the
Fig.1
AUDIO button and the screen will display as following:
Fig.2
Fig.3
In FIG.1, the user can adjust the value of BASS, TREBLE and SUB WOOFER by
tapping on + / - on the touch screen.
Tapping on
button to turn to previous page shown as fig.2.
In FIG.2, the user can turn on/off the BEEP and LOUD function by tapping ON or
OFF button.
Tapping on
button to turn to next page shown as fig.3.
In FIG.3, the user can adjust the sound output effect leftwards or rightwards by
tapping
button; the sound output effect frontwards or rearwards by
tapping
button.
3.Video
Press on the
VIDEO button and the screen will display as following:
In this setting, the user can adjust the value of CONTRAST, BRIGHTNESS and COLOR
by tapping on the items at the left/right end of each value bar.
According to the specific condition, the user can adjust the light effect on screen by
tapping SOFT, USER, NORMAL and BRIGHT modes.
12
REMOTE CONTROL
1
2
3
4
15
16
17
5
6
7
8
9
10
11
12
13
14
18
19
20
21
22
23
24
25
13
REMOTE CONTROL
Installing the battery
Slide the tray out on the back of the remote control and insert the battery with the plus
(+)and minus(-)poles pointing in the proper direction.
Use and care of the remote control
Point the remote control in the direction of the front panel to operate to use it.
Notes:
Using batteries improperly can cause them to explode. Take note of the following points:
* Keep the battery out of the reach of children. Should the battery be swallowed,
immediately consult a doctor.
* Use one CR2025(3V)lithium battery.
* Remove the battery if the remote control is not to be used for a month or longer.
* Do not short-circuit, disassemble or heat batteries.
* Do not dispose of batteries into fire or flames.
* Dispose of spent batteries properly.
* Do not let the remote control fall onto the floor, where it may become jammed under the
brake or accelerator pedals.
14
REMOTE CONTROL
1.PWR
Press this button to turn on the unit. Press and hold this button to turn off.
In power on, press to shut off the sound output, press it again to resume the previous sound level.
2.EQ
Press to select the corresponding preset modes to adjust the sound quality.
In BT mode, press to dial up a call.
3.ANGLE/AMS
Press to change the viewing angle in DVD mode.
In radio mode, press to browse each stored station for 5 seconds respectively which have been stored.
Long press to scan and automatically store stations.
4.SUB-T/LOC
In DVD playback mode, press to change the subtitle language.
In radio mode, press to select a local station or distance station.
5.PROG/A-B
In DVD/VCD/CD mode, short press to set the program order to play.
In DVD/VCD/CD mode, press and hold to repeat selected A-B section.
6.OSD/*
In DVD mode, press to display Title Elapsed, Title Remain, Chapter Elapsed, Chapter Remain,
DisplayOff.
In VCD/CD mode, press to display Single Elapsed, Single Remain, Total Elapsed, Total Remain,
Display Off.
In any mode, long press to display current time, current mode.
In BT mode, press this button to function as the button does on your cell phone.
7.GOTO/#
In DVD mode, press GOTO button and cursor button to select TITLE, CHAPTER, AUDIO, SUBTITLE,
ANGLE, TT TIME, CH TIME, REPEAT, TIME DISP. Then press ENTER button to set the item.
In VCD mode, press GOTO button and cursor button to select TRACK, DISC TIME, TRACK TIME,
REPEAT, TIME DISP. Then press ENTER button to set the item.
In CD mode, press GOTO button to select "Disc Go To:_ _ _", "Track Go To _:_ _:_ _", “Select
Track:_ _:xx".
Then press 0-9 number buttons to set the track or time what you want.
In radio mode ,press the button and the number button to set the frequency.
In BT mode, press this button to function as the button does on your cell phone.
8.MENU
Press to return to the root menu in DVD mode.
9. [ / ][ / ][ / / / ]/ENTER
In playback mode perform [fast reverse /fast forward][previous track/next track][upwards/downwards/
leftwards/rightwards] and then press ENTER to execute the entering or the selected item in the
system setting menu.
In radio mode, press / button to recall a stored station. Press / button to seek a station
automatically by short press and to seek a station manually by press and hold.
15
10.RPT/NAV
In disc playback mode, press this button to repeat playing.
Press and hold this button to start navigation mode.
11.
/PTY
In radio mode, press this button to function PTY on/off.In DVD/VCD mode, press to play slowly.
12. ZOOM/AF
In radio mode, press this button to function AF on/off.
In DVD/VCD mode, press to increase or decrease the picture in size.
13. SRC
Press the button repeatedly to switch sources.
14. VOL-/SEL/VOL+,LED
Press VOL-/VOL+ to adjust volume.
Press the button to start the system setup.
Press and hold LED button to switch between two LED modes.
15.
Short press to eject a disc.
Press and hold this button to force ejecting a disc when the system becomes frozen.
16. LOUD
Press this button to activate LOUD function.
In bluetooth mode, press this button to reject your calling.
17. 0~9 numerals
In radio mode, number buttons(from 1to 6)can help you store you favourite station.
In DVD/VCD/CD mode, press to select any chapter or track directly.
18.CLEAR
Press the button to clear the erroneous number what you import.
19.
Press to pause playing and press again to resume playing.
20.TITLE
In DVD mode, press the button to return the title menu.
In VCD mode, press this button to display PBC function.
21.
Press once to stop play. Press twice to stop completely.
22. BAND/P/N
In radio mode, press to select bands.
In DVD/VCD mode, press P/N button to select PAL, AUTO or NTSC.
23.SETUP
In playback mode, short press to display DVD setting.
Press and hold in DVD mode and press in other modes will display system settings.
24. AUDIO/ST
In DVD/VCD mode, press to change the audio language.
In FM mode, press to select stereo or mono reception.
25.RDM/TA
In radio mode, press this button to function TA on/off.
In playback mode, press to play tracks in a random order.
16
BASIC OPERATION
¼ò¹
µÊ
¥Å
ÕÅ
ÏÖ
³¸
ýÄÏ
1.Reset the Unit
Operating the unit for the first time or after replacing the car battery, you must reset the
unit.Press RESET button on the head unit with a pointed object, (such as a ballpoint
pen) to set the unit to initial status.
*This function can only be operated by the head unit.
2.Turning the Unit On/Off
Press PWR/
button on the remote control to turn on the unit. In unit ON, when insert
a disc, the unit will automatically start playing. Long press it to turn off the unit completely.
Pressing PWR/MUTE button on the front panel also performs the same operation.
Note:
After the unit is off, the volume level is memorized during the area between 0 and 30.
If it is set less than 6, it will resume to 6; if the set volume level is higher than 30,
it will resume to 30; if it is between 6 and 30, it still stores in the status which you set.
3.Volume Control
Press VOL+ button on the remote control to increase the sound level and press VOLbutton on the remote control to decrease the sound level.
Press ( + or -) on the front panel also performs the same operation.
4. Mute Function
Press PWR/
button to shut off the sound output. MUTE will be displayed on the
screen. Press it again to resume to previous volume level.
Press PWR/MUTE button on the panel also performs the same operation.
6.EQ Setting
While listening to the popular music, classic music or rock music, you can select the
corresponding preset modes to adjust the sound quality perfectly by using EQ button on
the remote control. Repeatedly pressing EQ button to choose the following modes in turn:
POP
EQ OFF
CLASSIC
ROCK
17
RADIO OPERATION
Selecting the radio mode, the TFT display as the follows:
FM1 P6
87.50MHz
1.Band Selector
In radio mode, repeatedly press BAND/P/N button on the remote control OR >/< button
one the touch screen to select a band in the following order:
FM1
FM3
FM2
MW2
MW1
2.Manual/Automatic Tuning
(1).Automatic Tuning: Press / button on the remote control to search for a station in
the direction of lower frequency or higher frequency.
(2). Manual Tuning: Press or button repeatedly to move downward or upward
one step respectively until the desired station frequency is displayed.
*Press(press and hold) / button on panel also performs the operation.
3.Recalling a preset station
A total of 30preset stations (18-FM,12-MW) are available in memory.
Press / button on the remote control to recall a preset station.
The display shows the preset number and frequency of the stored station, touch one of
these to select a corresponding station to listening.
*Press one of the station preset button on the remote control also selects preset station.
4.Automatic/Manual Store
Auto store is a function for storing up to 6 stations.
(1)Select the desired band.
(2)Hold down AMS button ,the stations with good reception are stored automatically.
Manual store: turn in a station you wish to store in the preset memory, press and hold
one the preset buttons (1-6) that you want to store on.
*If you store a station in a preset memory which already has a station the current station
will be cleared and replaced with the new station.
5.DX/LOC Selector
In radio mode, press LOC button on the remote control to select strong or weak station
reception.
(1). It is set to LOC mode when LOC button is first pressed. Loc:ON appears on the
screen and only strong signal station will be tuned.
(2).It is switched to DX mode when Loc: OFF is pressed again. Both strong and weak
stations can be received.
Note: The initial mode is DX mode.
6.MO/ST Selector
In FM of radio mode, you can press ST button on the remote control to select Mono mode
or Stereo mode.
18
RADIO OPERATION
RDS (RADIO DATA SYSTEM) OPERATION
The RDS allows you to receive a variety of information such as traffic information, station names,
and to automatically retune to a stronger transmitter that is broadcasting the same programme.
TIPS
The RDS digital data includes the followings:
PI Programme Identification
PS Programme Service Name
AF List of Alternative Frequencies
TP Traffic Programme
TA Traffic Announcement
PTY Programme Type
EON Enhanced Other Networks
FM1 P1
87.50MHz
Turn on/off the AF function
* Press AF button to switch on/off AF function.
*The tuner will searchfor a station with RDS information.
* The tuner will retune frequencies whenever the reception signals getting worse.
Receiving Traffic information
1.Press the TA button to switch on TA mode.
2.The unit search for traffic information station automatically. When a traffic information station is
tuned in, the TP mark display on touchable screen. If you do not want to listen to the traffic
information being received, press TA button to skip that traffic information message.
The TA function will remain in the ON position. And the unit will be back to previous mode.
3.Press it again to switch off TA mode.
* Traffic information is heard only when it is being broadcast.
In other mode, Traffic announcement can interrupt the source sound output when broadcast.
After broadcasted ,the unit will automatically return to the original source play before the traffic
information broadcast began.
PTY(Programme Type)Tuning
The PTY function allows you to search for stations with a particular Program Type. Touching
Page1 button on the radio display screen to switch to the RDS screen.
1.Press PTY button on touchable screen or on the remote control to select a programme type.
After selecting the programme type for 3 seconds, the unit will search for a station in the
selected programme type.
*If the PTY station is found, the tuner will be stop searching.
*If the PTY station is not found, No Pty will be displayed on the screen.
All types for your selection are listed in table as below:
NEWS
FINANCE
COUNTRY
CURRENT AFFAIR POP MUSIC
VARIED
CHILDREN
NATIONAL
INFORMATION
ROCK MUSIC
SOCIAL AFFAIR
OLDIES
SPORTS
M.O.R. MUSIC
RELIGION
FOLK
EDUCATION
LIGHT CLASSIC
PHONE IN
DOCUMENTARY
DRAMA
CULTURE
SERIOUS CLASSIC TRAVEL
LEISURE
OTHER MUSIC
SCIENCE
WEATHER
TEST
ALARM
JAZZ MUSIC
An emergency broadcasting(ALARM) will broadcast automatically and produce the beep sound
when it is received. The sound output through other source will be muted.
19
BLUETOOTH OPERATION
Select the BLUETOOTH mode
To select the BLUETOOTH mode, the users can make it done by the following ways:
1. Press on SRC/NAV button on the front panel to switch to BLUETOOTH mode;
2. Press on SRC button on the remote control to switch to BLUETOOTH mode;
3. Tap on the BLUETOOTH ICON at the MAIN MENU on the screen.
HANDS-FREE PHONE
The unit is compatible with Bluetooth international standard wireless communication
technology. You can place a hands-free call by using a Bluetooth compatible with the
mobile phone.
*When you place a call, speak loudly and clearly.
*Shut the windows before calling.
*It is normal that some unnatural voice may be heard during your calling which may be
caused by the conditions of the signals or the one who uses the mobile phone.
*Due to some special mobile phone, you may not be able to use a hands-free phone.
CONNECTING
Selecting BT mode
The connection is successful.
The TFT displays CONNECT.
Searching for device
(EONON) by using mobile
phone.
Selectting bluetooth device
(EONON) by mobile phone.
Input a pass code:1234
*The Bluetooth setting is required for a mobile phone. Read the Owner ,s Manual of
the mobile phone.
*After paired ,the unit can connect with the mobile phone automatically. in valid range
* If the mobile phone and the device are disconnected accidentally, the screen will display
Disconnect, just press LINK button on the screen to reconnect(refer to Bluetooth setup ).
NOTE
*Press / button on the remote control also performs dial(receiving) a call or hang up a
call function
*The incoming call will interrupt the sound output through other source, and switch to the
hands-free phone screen automatically when it is received. After the call is ended, the unit
will be back to the previous mode.
* The hands-free phone sounds output through the built-in speakers. When calling, press
Audio Transfer button on the screen to switch the mode to receive a call by using mobile
phone, and press it again to return to hands-free mode.
20
BLUETOOTH OPERATION
1. MAIN PAGE
After selecting the bluetooth mode, MAIN PAGE will display as FIG.1. The user can
dial up in this mode, input the number required by pressing number button on the
remote control or on the screen then press
button on remote control or on the
screen to dial up.
The telephone number you dialed is appeared on the DISPLAY COLUMN.
CLEAR
FIG.1
VOLUME BAR
BACK
MAIN PAGE
DISPLAY COLUME
PHONE BOOK
SETUP PAGE
A2DP PAGE
AUDIO
TRANSFER
DIGITS AREA
2. PHONE BOOK
Tap on PHONE BOOK button on the screen shown above, the screen will display as
following FIG.2.
There are three item : DIALED CALLS, RECEIVED CALLS and MISSED CALLS.
A maximum of 15 numbers can be stored in each call history. A maximum of 5 numbers
will be displayed in each page. Tap on
button to turn to previous/next page.(FIG.3)
You can place a call by selecting a number from a list of each item.
FIG.2
FIG.3
010XXXXXXXX
020XXXXXXXX
021XXXXXXXX
025XXXXXXXX
027XXXXXXXX
Receiving a Call
when a call is coming, the received call sound rings ,and the coming call number is
shown in the display. Press
button on the screen to starts the call.
End a Call or reject a call
Press
button on the screen or on the remote control to end or reject the call.
21
BLUETOOTH OPERATION
3. SETUP PAGE
Tap on SETUP PAGE button on the screen shown in FIG.1, the screen will display as
following FIG.4.
FIG.4
3.1 AUTO-ANSWER
ON: Tap on this button then the coming call will be answer automatically.
OFF: Tap on this button then the coming call will not be answer automatically.
3.2 CONNECT
AUTO: Tap on this button then the unit and the device will be reconnected automatically.
MANUAL: Tap on this button then the unit and the device will be reconnected manually.
3.3 PAIR
Tap on this button to pair up the unit and the device.
3.4 RESET
Tap on this button to reset the bluetooth setup.
4. BLUETOOTH AUDIO FUNCTION
Tap on A2DP PAGE button on the screen shown in FIG.1, the screen will display as
following FIG.5.
Audio information of a bluetooth, compatible with mobile phone, portable player, etc.,
is transferred by wireless technology.
FIG.5
Play/pause
Previous/next track
Stop playback
Refer to CONNECT details to connect bluetooth audio devices.
NOTE
*Video playback is not supported.
*Using remote control also performs the same operation.
22
DVB-T OPERATION
This equipment will serve you with the available received channels supplied by
the mobile signals. Press SRC button on the panel or on the remote control or
touch on the rght top of the screen then select TV mode.
Touch at random area to start the operation.
Main menu:
1
3
4
2
1.
To display the channel list
2.
To be back to previous interface
3.
To adjust the volume control
4.
To display the main menu
5.
To select the channels
5
Search automatically
The unit can receive and store the channels according to the strength of the
signal received after finishing searching the channel, all the searched
station will be displayed and touch
button to save it.
Touch
to be back to previous menu.
Search manually
Touch
button to switch frequencyand touch OK button to confirm it.
23
DVB-T OPERATION
Display setup
Language
To switch the languagesof the channels and touch OK buttonto select.
Screen
To adjust the ratio and format of the screen.
OSD
To setup the background of the screen.
SYSTEM SETUP
Country To select the country or area.
*The preset channels will be clearedif the setup is changed.
Version To displaythe version info.
Reset Default To reset the setting.
*All the preset setting will be cleared.
When a channel is searched, touchbutton to display the channel list.
Press >>I/I<< buttons on the remotecontrol or touch
button to select
channels and touch
button towatch the selected channels.
Touch /
button to switch modes between TV and radio and touch
button to confirm the selection.
24
DVD/VCD/CD OPERATIONS
Loading a disc
1.Press button to open the front panel.
2. Insert a disc into the Disc slot the unit switch to the DVD mode automatically
* You can eject a disc by pressing
button on the unit.
Quick track selection fast forward/fast reward playback
During playback mode, press
/
button to select next/previous chapter or track.
*Press
/
button on the unit also perform the same operation.
Press the /
button on the remote control to perform fast reward or fast forward.
Repeatedly press the button ,the options switch as following order:
32
*Press and hold the
/
button on the unit will perform the same function.
Stop the playback
Press button to stop playing, then press ENTER button to play the current chapter or
track, press
button twice to stop playing completely, then press ENTER button to play
the beginning of disc.
Pause the Playback
Press button to pause the playback,press it again to return to normal playback.
*Pressing button on the front panel also perform the same operation.
Playing Tracks in Random Order
During DVD/VCD/CD playback, press RDM button, RANDOM will appear on the
display, the unit plays any track at random and the number selection is de-available.
Press it again to return to normal playing.
Repeat Playing
In playback mode, press RPT on the remote control to perform replaying function when
you need to repeat the chapter you like.
During DVD playback, the replay option change in following order:
TITLE
CHAPTER
OFF
During VCD /CD playback, the replay option change in following order:
TRACK
OFF
*The defaulted setting is disc repeated.
Slow motion playback
In DVD mode, press
repeatedly to slow forward or slow reward, as follows:
12
14
1 16
1 16
18
18
14
12
In VCD mode,press repeatedly to slow forward in following order.
25
12
18
14
Normal Play
1 16
This function is operated by using the remote control.
Increase or decrease the size of the picture
During DVD/VCD playback, press ZOOM button to increase or decrease the picture size.
There are 6 sizes, and press the button repeatedly to change the size in following order.
2X
OFF
14
3X
4X
12
13
*This function is operated by using the remote control.
Selecting the channel mode(VCD mode)
In VCD mode, press the AUDIO button on the remote control repeatedly to select the
channel mode in the following order:
MONO LEFT
STEREO
MONO RIGHT
MIX-MONO
Programmed playback
In DVD/VCD/CD mode, press the PROG button and the program menu will be displayed.
Press the number buttons to select the track number. Use the direction buttons to move
the cursor to START and press ENTER to start programmed playback. Move the cursor
to EXIT and press ENTER to exit the programmed playback. Move the cursor to PREV
and press ENTER to go to the last page; move the cursor to NEXT and press ENTER to
go to the next page. During this process, press PROG to cancel the programmed playback.
* This function can only be operated by using the remote control.
Changing the subtitle language(Multi-subtitle)
With DVDs featuring multi-subtitle recordings. You can press SUB-T to switch between
subtitle languages during playback.
Selection options switch as follows:
Subtitle 01
Subtitles 2
Subtitles OFF
Notes:
* This function only operates with DVDs featuring multi-subtitle recordings.
* This function is operated by using the remote control.
Changing the audio language
DVDs can provide audio playback with different language. With DVDs featuring multiaudio
recordings, you can press AUDIO button to switch between language and audio systems
during playback. Selection options switch as follows:
Audio 01
Audio 02
Notes:
* This function only operates with DVDs featuring multi-audio recordings.
* This function is operated by using the remote control.
26
Selecting different title (DVD mode)
For DVD disc, you can press TITLE on the remote control to return the top menu of the
disc, and you can select different chapter or title upward or downward by using
or
.
*Touching the screen also perform the same function(refer to page 7 Multi-player
operation for detail).
Selecting root menu(DVD mode)
For DVD disc, you can press MENU to select different root menus, and then press
[ENTER] buttons to enter the sub-menus. With pressing
buttons, and the number buttons then ENTER button to select and enter what
you desired.
Setup menu
In DVD/VCD/CDmode, press SETUP,the screen will display system setting picture,
the user can select some relative constant parameters. The user also can set it as
needed by moving the cursor and using
buttons, and then press ENTER
to execute the selecting or entering item.
*This function is operated by using the remote control.
Notes:
* The selections are the preferred options that will be chosen if they are available on a
disc. If the disc that is inserted does not have the preferred option then the discs own
preference will be used.
* Regarding SETUP MENU, please refer to the following pages for more details.
* Some functions varies depending on the types of models or formats of the disc.
Auto switch to video
When playing DVD in driving car,there is Attention: Cann,t use function When driving
display on screen. Just braking car, the screen can switch to video automatically.
Auto switch when revering the car
The unit can switch to the radar of revering the car automatically,when revering the car.
27
SYSTEM SETUP
When you press SETUP button on the remote control, or press SETUP button on the screen, the setup menu
will be displayed. It includes General Setting, Audio Setup, Preference ,Password Setup and Exit Setup menu.
1.Within the setup menu, you can use
[
][
][
][
] buttons on the remote control to move the cursor,
and then press the ENTER button to make your selection.Press [
] can return to the previous menu.
2.To exit setup menu, you can select the EXIT item in sub-menu or press SETUP button.
Note:touching the item on the screen also performs same operation.
1. GENERAL SETUP PAGE
1.1 TV DISPLAY
GENERAL SETUP PAGE
TV DISPLAY
WIDE 4:3 PAN SCAN
OSD LANGUAGE ENG 4:3 LETTER BOX
16:9 WIDE
SET TV DISPLAY MODE
The TV Display which select the different ratio of display format and the screen of TV, There are
various types of display on screen for different matches between Disc and TV.
Note:
No matter which display format is selected, a picture recorded in standard 4:3 format always displays in
the 4:3 aspect ratio.
The display format of DVD titles may vary; please refer to the information that accompanies your specific
DVD title.
If the DVD title is recorded in 16:9 wide display format while the TV is a standard 4:3 screen, horizontal
compression of the image will result.
Some DVD titles may be recorded in special formats. In such cases, the DVD titles will always appear on
the screen in their original format,regardless of which TV display format you select.
1.2 OSD LANGUAGE
On Screen Display(OSD)Language:Users can select the on-screen display language.
GENERAL SETUP PAGE
TV DISPLAY
OSD LANGUAGE
WIDE
ENG
SET OSD LANGUAGE
28
ENGLISH
FRANCAIS
DEUTSCH
ITALIANO
PORTUGUESE
ESPANOL
2. AUDIO SETUP PAGE
User can select digital audio setup or dolby digital setup.
AUDIO SETUP PAGE
DOLBY DIGITAL SETUP
2.1 DOLBY DIGITAL SETUP
DOLBY DIGITAL SETUP PAGE
DUAL MONO
DYNAMIC
STR
STEREO
L-MONO
R-MONO
MIX-MONO
DUAL MONO(1+1) SETUP
DUAL MONO:User can switch the binaural mode.
DYNAMIC:Select the provided option to change the Dynamic range setting.
3. PREFERENCE SETUP PAGE
The preference setting is active only when disc has been stopped completely, and the setting is
effective on next time power on till exchanging the saved setting.
3.1 AUDIO
AUDIO: Sets the preferred audio language as the default when playing DVD. (If DVD support these
languages).
PREFERENCE PAGE
ENG
AUDIO
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
ENGLISH
FRENCH
SPANISH
PORTUGUES
JAPANESE
KOREAN
RUSSIAN
THAI
PREFERRED AUDIO LANGUAGE
29
3.2 SUBTITLE
SUBTITLE: Sets the preferred subtitle language as the default when playing DVD.(if DVD support
these languages).
PREFERENCE PAGE
AUDIO
ENG
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
ENGLISH
FRENCH
SPANISH
PORTUGUES
JAPANESE
KOREAN
RUSSIAN
THAI
PREFERRED SUBTITLE LANGUAGE
3.3 DISC MENU
DISC MENU: Sets the preferred menu language as the default when playing DVD.(if DVD support
these languages).
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
ENG
ENG
ENG
ENGLISH
FRENCH
SPANISH
PORTUGUES
JAPANESE
KOREAN
RUSSIAN
THAI
PREFERRED MENU LANGUAGE
3.4 PARENTAL
PARENTAL: The parental control function works in conjunction with the different censorship classes
assigned to DVDs. These classes help to control the types of DVDs that the family watches, there
are up to 8 censorship classes for DVDs.
Note:
The PARENTAL is changeable when 4.1 PASSWORD MODE set to OFF.
After setting the level of parental control. Please set the password as ON to perform the lock of changing.
PREFERENCE PAGE
AUDIO
ENG
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
1.KID SAF
2.G
3.PG
4.PG 13
5.PG R
6.R
7.NC 17
8.ADULT
SET PARENTAL CONTROL
3.5 DEFAULT
DEFAULT: Resets to the initial factory setups.Press ENTER button to confirm.
PREFERENCE PAGE
AUDIO
ENG
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
LOAD FACTORY SETTING
30
RESET
4. PASSWORD SETUP PAGE
4.1 PASSWORD MODE
PASSWORD MODE: Sets the function operation to locking the parental function.
ON: Using the parental control must input the password.
OFF: You can not input the password to change the parental control.
* The initial password is 136900.
PASSWORD SETUP PAGE
PASSWORD MODE
PASSWORD
ON
ON
OFF
PASSWORD MODE
4.2 PASSWORD CHANGE
PASSWORD CHANGE: You can change the password, please type 6 numerals as new password.
PASSWORD SETUP PAGE
PASSWORD MODE
PASSWORD
ON
CHANGE
OLD PASSWORD
NEW PASSWORD
CONFIRM PWD
OK
CHANGE PASSWORD
Note:Touching the position where inputting password, the screen will display the number button,and
user can input the password by touching number button.
5. EXIT SETUP MENU
EXIT SETUP MENU
Moving the cursor to
by using direction key on the remote control, then press ENTER button to
exit the setup. Touching the
to exit directly.
31
SETTING THE TV SCREEN SIZE
Multi-aspect ratios suit to different TV screen size.
Picture format
on Disc
TV Screen Size
16:9
4:3
Pan Scan
Letter-box
Wide Screen
4:3
16:9
Function supported by DVD discs
There are many functions available on DVD discs and the functions vary per player and
per manufacturer.
ALL
32
Regional code and signal system
Picture proportion modes
DTS surround
Parent lock
Number of languages
Angles for viewing
Subtitle languages
Closed Caption
MP3 OPERATION
Playing a disc, an SD/MMC card or a USB device containing MP3 files
Connect a USB device or press button to open the front panel, insert a disc into the
disc slot or SD/MMC card into the card slot. The unit will automatically switch on when
a disc, card or USB device is inserted. The screen will display as follow:
Touch this area to display number keyboard.
MP3
02:47 03:40
001/099
01 LA LUNE
01IN PARADISUM
02 NO ONE LIKE
02 WINTER IN J
03 SCARBOUGH
1
1.
2.
3-4.
5.
6.
2
3
4
5
6
: To start/pause the playback.
: To stop playing, touch twice to stop completely.
: To select previous/next chapter or track.
: To play in random order.
: To select one of the repeat modes.
/
button on the screen to turn pages.
Touch the
*Press
/
button on the remote control when stop playback also performs the same
function.
*You can eject a disc by pressing
button on the unit.
Repeat playing
When playing MP3 files, press the RPT button repeatedly on the remote control to select
repeat mode: REPEAT ONE, OFF. While in REPEAT ONE mode, it will play one track
repeatedly. The defaulted mode is REPEAT ALL mode, the unit will play all tracks repeatedly.
Track selection
-Skip track backward/forward
When playing MP3 files, press
/
button on the remote control or press NEXT/PREV
button on the touchable screen to go to the previous or next track.
33
- Selecting track by using number button
Selecting any track directly by using Number button(0-9).
To select more than 9 track number, press the corresponding number buttons continuously.
For example, if you want to play the 23th track, just press button 2 and then press button 3
and the corresponding track will be played.
Note:
* This function can be operated using the remote control or touch the exact track by
number keyboard jumped out to be functioned.
* If you make a mistake, press CLEAR button to clear.
Stop playing
When playing MP3 files, press
button on the remote control to stop playback.
Pause playback
Press the
button on the remote control or press PAUSE button on the touchable
screen while playing, press it again or press PLAY button on the touchable screen
to return to normal playback.
Fast-forward/fast-backward playing
Press /
button on the remote control to select the speed of fast playing in backward
or forward direction:
2 --4 --8 --16 --32 -*Long press
function.
/
button continuously on the front panel also perform the same
ISO FILE OPERATION
When playing the media with folders, press the
/
button on the remote control
or PREV/NEXT buttons on the screen to move the cursor to current folder then press
ENTER button on the remote control to confirm, and the first track of the current
folder will be played.
34
NAVIGATION OPERATION
The GPS system can navigate with voice, when you do not drive on your preset line,
the system will reset the line automatically to get the destination.
Press
button on the unit to open the panel, the SD card slot is at the bottom of the
panel (shown as illustration). It supports SD card with memorized navigation map only.
SD card slot
Press SRC button on the unit or on remote control repeatedly to access the navigation
mode after insert SD card with stored navigating map.
*Long press SEL/NAV button on the unit or on remote control or Touching NAV item on
source selection screen also activate the function.
Calibration
To avoid the touching effect function invalid,please calibrate the touchable screen
before perform navigating operation.
Press
button on the touchable screen and the screen display as following:
Please use something with needle end touching on the + button to finish the calibration.
35
NAVIGATION OPERATION
PATH SETTING
Click PATH SETTING button, pointing to the
your SD card(shown as illustrated).
.exe
file in the navigation software in
Press OK button to start-up the software.
The navigation will auto-started after setting. Press CANCEL button to exit
the PATH SETTING mode.
NO TE
Once the SD card could not eject automatically after pressing, just take it out manually.
Touch the selection displayed on screen to perform the corresponding operation.
For more information regarding the NAV. Operation, please refer to the user manual
of navigating electronic map.
Please confirm your place is not under the bridge, on the tunnel or near the building
which can infect the signal received.
For safety, please avoid operating the system while driving.
GPS system is operated in background at any modes.
Do not take the SD card out when navigating to avoid freeze the unit
36
INSTALLATION
Notes
Before finally installing the unit, connect the wiring temporarily, making sure it is all
connected up properly, and the unit and the system work properly.
Use only the parts included with unit to ensure proper installation. The use of unauthorized
parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger
if there is a sudden stop.
The semiconductor laser will be damaged if it overheats, so don't install the unit anywhere
hot--for instance, near a heater outlet.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
30
The cords must not cover up the area shown in the figure below. This is necessary to
allow the enginery to radiate freely.
Do not close the back area
37
INSTALLATION
Install the unit
After inserting the holder into the dash-board,select the appropriate tabs according to the
thickness of the dash-board material and bend them.(Install as firmly as possible using the
top and bottom tabs. To secure, bend the tabs 90 degrees.)
Insert the keys supplied to the unit at both sides of the unit (shown as illustrated)until
they click. Pulling the keys makes it possible to remove the unit from the dashboard.
38
TROUBLE SHOOTING
Common problems
Symptom
Cause
Remedy
Power doesn't switch ON .
The unit doesn't operate.
Leads and connectors are
incorrectly connected.
Confirm once more that all connections
are correct.
A fuse has blown.
Fix the problem causing the blown fuse
and replace the old fuse with a new one
of the same capacity.
Noise and other factors are
causing the built-in microprocessor to operate incorrectly.
Reset the unit.
The remote control operation
mode is incorrect.
Switch to the correct remote control
mode.
Battery power is low.
Load new batteries.
Some operations are prohibited
with certain discs.
Check using another disc.
The disc is dirty.
Clean the disc.
The loaded disc is a type this
unit cannot play.
Check the type of the disc.
Non compatible video system
disc is loaded.
Change to a disc compatible to your
video system.
Connections are incorrect.
Check connections
With some discs,96kHz output
is prohibited.
Switch the output setting to 48 Khz.
The unit is performing still F.FWD
or F.REV playback.
There is no sound during still F.FWD ,
F.REV playback.
The operation is prohibited for
the disc.
This operation is not possible.
The operation is not compatible
with the disc's organization.
This operation is not possible.
The picture stops (pauses)
and the unit cannot be
operated.
Reading of data has become
impossible during playback.
After pressing
once more.
There's no sound Volume
level is low.
The volume level is low.
Raise the volume level.
There's audio and video
skipping.
This unit is not firmly secured.
Secure this unit firmly.
The picture is stretched the
aspect is incorrect.
The aspect setting is incorrect
for the display.
Select the appropriate setting for your
display.
When the ignition switch is
turned ON (or turned to ACC),
the motor sounds.
This unit confirms whether a
disc is loaded or not.
This is a normal operation.
Operation with the remote
control isn't possible.
Playback is not possible.
There's no sound.
The prohibited mark
is
displayed and operation is
not possible.
once start playback
39
Problem during DVD playback
Symptom
Cause
Remedy
Playback is not possible
The loaded disc has a different
region number from this unit
Replace the disc with one featuring the
same region number as this unit
Dialog language (and
subtitle language) can not
be switched.
The DVD playing does not
feature multiple language
recordings.
You cannot switch among multiple
languages if they aren't recorded on
the disc
You can only switch between
Switch using the disc menu
options indicated in the disc menu
No subtitles are displayed
The DVD playing does not feature Subtitles are not displayed if they are
subtitles
not recorded on the disc
You can only switch between
Switch using the disc menu
options indicated in the disc menu
Playback is not with the
audio language and subtitle
language settings selected
in SET UP MENU
The DVD playing does not
feature dialog or subtitles in
the language selected in the
SET UP MENU
Switching to a selected language is not
possible if the language selected in the
SET UP MENU is not recorded on the disc
The picture is extremely
unclear/distorted and dark
during playback
The disc features a signal to
prohibit copying (some discs
may have this)
Since this unit is compatible with the copy
guard analog copy protect system. when
playing a disc that has a signal prohibiting
copying the picture may suffer from
horizontal stripes or other imperfections
when viewed on some displays. This does
not mean this unit is malfunctioning.
Problem during Video CD playback
Symptom
Cause
Remedy
The PBC(playback control)
menu display cannot be
called up.
The video CD playing does not
feature PBC
This operation is not possible with video
Cds not featuring PBC
PBC is switched OFF
Switch PBC ON
PBC is switched ON
Switch PBC OFF.
Repeat play and track/time
search are not possible
40
CABLE CONNECTION
1
2
3
4
5
6
7
8
9
10
1 Shallow gray/White Plug
2 Shallow gray/Red Plug
3 Deep gray/White Plug
4
5
6
7
8
9
10
11
12
13
14
15
16
AUDIO OUT R.R
AUDIO OUT F.L
Deep gray/Red Plug
AUDIO OUT F.R
Black/Black Plug
IR
Orange
SWC1
Black
GND
Brown
SWC2
Brown/Brown Plug
SUB WOOFER OUT
Black/Black Plug
GPS ANT
Gray/Yellow Plug
REAR VIDEO OUT1
Gray/Yellow Plug
REAR VIDEO OUT2
Brown/Yellow Plug
REVERSE VIDEO IN
Black/Yellow Plug
VIDEO IN
Black/White Plug
AUX IN-L
Black/Red Plug
AUX IN-R
A1.PARKING BRAKE
A2.TEL MUTE
A3.REVERSE GEAR
A4.BATTERY
A5.ANTENNA POWER+
A6.ILL
A7.IGNITION KEY
A8.GROUND
11
12
13
14
15
16
AUDIO OUT R.L
B1.SPEAKER REAR R+
B2.SPEAKER REAR RB3.SPEAKER FRONT R+
B4.SPEAKER FRONT RB5.SPEAKER FRONT L+
B6.SPEAKER FRONT LB7.SPEAKER REAR L+
B8.SPEAKER REAR L-
DVB-T ANT
RADIO ANT
5
7
2
4
6
8
1
3
5
7
2
4
6
8
1
B
A
3
ACCESSORIES
Mounting Bracket (Half Sleeve) -------------------------------------------------------X1
Removable Trim Ring equipped on the unit ---------------------------------------- X1
Mounting Screw M5 --------------------------------------------------------------------- X1
Washer ------------------------------------------------------------------------------------- X1
Rubber ------------------------------------------------------------------------------------- X1
Remote Control --------------------------------------------------------------------------- X1
Mount strap -------------------------------------------------------------------------------- X1
Release key ------------------------------------------------------------------------------ X2
User manual ----------------------------------------------------------------------------- X1
Wire connector -------------------------------------------------------------------------- X1
USB connector--------------------------------------------------------------------------- X1
AV cable ---------------------------------------------------------------------------------- X1
Screws(M5X60)-------------------------------------------------------------------------- X4
Screws(M24)------------------------------------------------------------------------------ X1
DVB-T antenna -------------------------------------------------------------------------- X1
GPS antenna ----------------------------------------------------------------------------- X1
41
SPECIFICATON
GENERAL
power requirement ---------------------------------------------- 12VDC(10.8~16V)
grounding system -------------------------------------------------------negative type
max: current consumption ------------------------------------------------------- 15 A
max: power output -------------------------------------------------------------- 65Wx4
load impedance -------------------------------------------------------------- 4 or 8
dimensions--------------------------------------------180(L) 160(W) 100(H)MM
weight--------------------------------------------------------------------------------3.3KG
DVD PLAYER
S/N ratio --------------------------------------------------------more than 60dB(1kHz)
dynamic range -----------------------------------------------more than 80dB(1kHz)
distortion ----------------------------------------------------------------less than 0.15%
video output ------------------------------------------------------- 1.0Vp--p+0.2V/75
audio output (RCA) ------------------------------------------- 2.0Vrms+0.3V 10K
FM TUNER
frequency range ---------------------------------------------------87.5~108.0MHz
usable sensitivity --------------------------------------------------------------->15dB
S/N ratio -------------------------------------------------------------------- 50dB(mono)
distortion --------------------------------------------------------------------1%(mono)
stereo separation ---------------------------------------------- 30dB(65dBu,1kHz)
MW TUNER
frequency range ----------------------------------------------------- 522~1620 kHz
usable sensitivity ---------------------------------------------------------------> 35dB
signal-to-noise ratio ------------------------------------------------------------- 40dB
42
Download PDF