Finesse technical manual -

Finesse technical manual -
EN
FINESSE
VCF-B-xxx-...
VCF-C-xxx-...
Full manual
B01-0211-0713-15
INSTALLATION
2
1. BEFORE YOU BEGIN
Meaning of symbols in the manual:
SYMBOL
MEANING
ATTENTION!
Warning/caution
DO NOT OVERLOOK!
Important instructions
YOU WILL NEED
NOTE
Practical tips and information
TECHNICAL INFORMATION
More detailed technical information
LINK
Refer to other parts/sections
of the manual
Before installation, thoroughly read the section “Safe use of air curtains”. It contains all instructions
on the safe and correct use of the product.
This manual contains important instructions to ensure correct installation of the air curtain. Before
installation, read all of the following instructions thoroughly and then adhere to them! The manufacturer reserves the right to make changes, including to technical documentation without
prior notice. Save this user manual for further use. The instructions in this manual are a part of the
product.
Statement of compliance
You will find the details at the www.2vv.cz website
2
2. UNPACKING
2.1 CHECK THE SHIPMENT
2.2 UNPACK THE AIR CURTAIN
•
Caution! Before removing the curtain from the
board, remove the cover.
1.
•
•
•
•
•
After delivery, immediately check to see if the
packaged product is damaged. If the packaging is damaged contact the delivery service. If the complaint is not fi led in time, your
claim may not be valid later.
Check to see if it is the same product you orderot. If there are any discrepancies, do not unpack the curtain, and immediately report the
defect to the supplier.
After unpacking, check to see if the curtain
and other parts are in order. If you have any
doubts, contact the supplier.
Never install a damaged air curtain!
If you do not unpack the curtain immediately
after delivery, it must be storot in a dry indoor
environment with an ambient temperature
between +5 °C and +40 °C
2.
•
+40 oC
+5 C
o
If the curtain has been transported at temperatures below 0° C, it will be necessary to let it
sit for at least 2 hours under normal operating
conditions after unpacking, without turning
it on. This will allow the air curtain‘s interior te
perature to stabilise.
All used packaging materials are environmentally friendly and may be
reused or recycled.
Take an active part in environmental protection and see that packaging
materials are correctly disposed of
or repurposed.
3
3. MAIN PARTS
3
6
1
2
4
7
5
1 Suspension holders
2 Water coil connection ¾“
3 Power supply cable plug
4 Power supply connectors and fusse location
5 Control modul socket
6 Inlet face cover
7 Outlet grid
4
4. DIMENSIONS
25
A
594,6
638,5
596,5
250
299,3
304,1
B
C
Type
Spacing of installation
Length B
Length of cover C
holes A [mm]
[mm]
(mm)
VCF-x-100-x-...
1085
1124,1
1166,1
VCF-x-150-x-...
1585
1624,1
1666,1
VCF-x-200-x-...
2085
2124,1
2166,1
VCF-x-250-x-...
2465
2504,1
2546,1
5. TECHNICAL PARAMETERS
Type
Max.
Air
Noise*
Heater
Heater
Fan power
Weight
height
output
[dB(A)]
doors
[m3/h]
output
power
supply
[kg]
[kW]
supply
[V/A]
[m]
[V/A]
VCF-B-100-E-...
2250
57,9
9,1
400/15,5
230/2,2
39,5
VCF-B-150-E-...
3230
60,2
14,7
400/25,2
230/3,3
54,5
VCF-B-200-E-...
4360
61,2
19,1
400/31,3
230/4,4
71
VCF-B-250-E-...
5300
62,8
24,5
400/41,1
230/5,4
85
2140
57,5
24,77**
-
230/2,2
41
VCF-B-150-V-...
3100
59,6
38,77**
-
230/3,3
56
VCF-B-200-V-...
4280
61
52,61**
-
230/4,3
73
VCF-B-250-V-...
5140
62,5
62,29**
-
230/5,4
87
VCF-B-100-V-...
4
The distance at which the average velocity of the air current flow drops to 3m/s. For optimal conditions and maximum
performance of the equipment.
* Acoustic pressure at a distance of 3 m from the curtain.
** With water temperature gradient of 90º/70° C and temperature of suctioned air at +18°C
*** With water temperature gradient of 40º/30° C and temperature of suctioned air at +18°C
5
5. TECHNICAL PARAMETERS
Type
Max.
Air
Noise*
Heater
Heater
Fan power
Weight
height
output
[dB(A)]
output
power
supply
[kg]
doors
[m3/h]
[kW]
supply
[V/A]
[m]
VCF-B-100-S-...
[V/A]
2270
58,3
-
-
230/2,2
37,5
3280
60,2
-
-
230/3,4
51
4400
61,5
-
-
230/4,2
66
VCF-B-250-S-...
5460
62,7
-
-
230/5,4
80
VCF-C-100-E-...
2960
61,2
9,6
400/17,9
230/4,0
44
VCF-C-150-E-...
4080
62,7
14,7
400/27,2
230/5,2
60
VCF-C-200-E-...
5180
64
19
400/34,3
230/6,8
75,5
VCF-C-250-E-...
6020
65,8
23,6
400/42,8
230/7,9
90
VCF-C-100-V-...
2800
61,2
29,13**
-
230/3,8
45,5
VCF-C-150-V-...
3900
62,5
44,57**
-
230/5,2
61
VCF-C-200-V-...
5070
63,7
56,99**
-
230/6,5
77
5860
65,6
67,3**
-
230/7,6
91,5
2530
61,6
13,47***
-
230/3,6
51,5
VCF-C-150-W-...
3500
62,6
19,03***
-
230/4,8
70,5
VCF-C-200-W-...
4670
63,7
25,71***
-
230/6,0
89
VCF-C-250-W-...
5260
65,2
29,81***
-
230/7,1
106
VCF-C-100-S-...
3020
61,9
-
-
230/3,9
42
VCF-C-150-S-...
4160
63
-
-
230/5,2
56,5
VCF-C-200-S-...
5270
64,2
-
-
230/6,7
71
VCF-C-250-S-...
6100
65,7
-
-
230/7,9
84
VCF-B-150-S-...
VCF-B-200-S-...
VCF-C-250-V-...
VCF-C-100-W-...
4
5
The distance at which the average velocity of the air current flow drops to 3m/s. For optimal conditions and maximum
performance of the equipment.
* Acoustic pressure at a distance of 3 m from the curtain.
** With water temperature gradient of 90º/70° C and temperature of suctioned air at +18°C
*** With water temperature gradient of 40º/30° C and temperature of suctioned air at +18°C
Air curtains with electrical heater
Type
6
Air flow
Heater output
Output temperature Δt
[m3/h]
[kW]
[°C]
VCF-B-100-E-...
2250
9,1
12,1
VCF-B-150-E-...
3230
14,7
13,5
VCF-B-200-E-...
4360
19,1
13,1
VCF-B-250-E-...
5300
24,5
13,8
VCF-C-100-E-...
2960
9,6
9,7
VCF-C-150-E-...
4080
14,7
10,7
VCF-C-200-E-...
5180
19
10,9
VCF-C-250-E-...
6020
23,6
11,7
5. TECHNICAL PARAMETERS
Air curtains with a water coil for a water temperature gradient of 90º/70° C and at an intake air
temperature of +18° C
Type
Air flow
Heat output
Outlet
Water flow
Pressure loss
[m3/h]
[kW]
temperature [°C]
[l/s]
[kPa]
VCF-B-100-V-...
2140
24,77
52,7
0,29
12
VCF-B-150-V-...
3100
38,77
55,5
0,46
29,1
VCF-B-200-V-...
4280
52,61
54,9
0,62
24,1
VCF-B-250-V-...
5140
62,29
54,4
0,74
17,8
VCF-C-100-V-...
2800
29,13
49,2
0,35
14,5
VCF-C-150-V-...
3900
44,57
52,3
0,53
35,1
VCF-C-200-V-...
5070
56,99
51,7
0,68
27
VCF-C-250-V-...
5860
62,29
54,4
0,74
17,8
Air curtains with a water coil for a water temperature gradient of 80º/60° C and at an intake air
temperature of +18° C
Type
Air flow
Heat output
Outlet
Water flow
Pressure loss
[m3/h]
[kW]
temperature [°C]
[l/s]
[kPa]
VCF-B-100-V-...
2140
20,28
46,4
0,24
8,8
VCF-B-150-V-...
3100
31,78
48,8
0,38
20,8
VCF-B-200-V-...
4280
43,15
48,3
0,51
17,7
VCF-B-250-V-...
5140
51,07
47,8
0,61
13,4
VCF-C-100-V-...
2800
23,88
43,6
0,28
10,9
VCF-C-150-V-...
3900
36,57
46,1
0,43
25,3
VCF-C-200-V-...
5070
46,72
45,6
0,55
19,8
VCF-C-250-V-...
5860
51,07
47,8
0,61
13,4
Air curtains with a water coil for a water temperature gradient of 70º/50° C and at an intake air
temperature of +18° C
Type
Air flow
Heat output
Outlet
Water flow
Pressure loss
[kPa]
[m3/h]
[kW]
temperature [°C]
[l/s]
VCF-B-100-V-...
2140
15,98
40,4
0,19
6,2
VCF-B-150-V-...
3100
25,07
42,3
0,3
14,2
VCF-B-200-V-...
4280
34,05
41,9
0,4
12,4
VCF-B-250-V-...
5140
40,28
41,5
0,48
9,7
VCF-C-100-V-...
2800
18,82
38,2
0,22
7,9
VCF-C-150-V-...
3900
28,87
40,2
0,34
17,2
VCF-C-200-V-...
5070
36,88
39,8
0,44
13,8
VCF-C-250-V-...
5860
40,28
41,5
0,48
9,7
7
5. TECHNICAL PARAMETERS
Air curtains with a water coil for a water temperature gradient of 60º/40° C and at an intake air
temperature of +18° C
Type
Air flow
Heat output
Outlet
Water flow
Pressure loss
[m3/h]
[kW]
temperature [°C]
[l/s]
[kPa]
VCF-B-100-V-...
2140
11,83
34,6
0,14
4,1
VCF-B-150-V-...
3100
18,59
36
0,22
8,8
VCF-B-200-V-...
4280
25,25
35,7
0,3
8,1
VCF-B-250-V-...
5140
29,85
35,4
0,35
6,6
VCF-C-100-V-...
2800
13,93
32,9
0,17
5,4
VCF-C-150-V-...
3900
21,41
34,5
0,25
10,8
VCF-C-200-V-...
5070
27,28
34,1
0,32
8,9
VCF-C-250-V-...
5860
29,85
35,4
0,35
6,6
Air curtains with a water coil for a water temperature gradient of 40/30° C and at an intake air
temperature of +18° C
Type
Air flow
Heat output
Outlet
Water flow
Pressure loss
[m3/h]
[kW]
temperature [°C]
[l/s]
[kPa]
VCF-C-100-W-...
2530
13,47
34
0,2
13,2
VCF-C-150-W-...
3500
19,03
34,3
0,4
14,1
VCF-C-200-W-...
4670
25,71
34,5
0,5
13,3
VCF-C-250-W-...
5260
29,81
35
0,6
16,3
Air curtains with a water coil for a water temperature gradient of 35/25° C and at an intake air
temperature of +18° C
Type
Air flow
Heat output
Outlet
Water flow
Pressure loss
[m3/h]
[kW]
temperature [°C]
[l/s]
[kPa]
VCF-C-100-W-...
2530
9,4
29,2
0,2
8,6
VCF-C-150-W-...
3500
13,3
29,4
0,3
8,2
VCF-C-200-W-...
4670
18
29,6
0,3
8,4
VCF-C-250-W-...
5260
21
30
0,4
9,4
The warm-water temperature coil, made of copper-aluminium alloy, is designed for a
maximum operational water temperature of +100° C and a maximum operating pressure of 1.6 MPa.
8
6. INSTALLATION
6.1 CHOOSE THE INSTALLATION SITE AND INSTALL THE AIR CURTAIN
304,1 mm
6.1-1 Built up dimensions
594,6 mm
•
•
•
•
•
min. 300 mm
The air curtain must be installed only in a horizontal position!
The curtain can be installed over the door opening. All separation distances for flammable materials
and safe use of air curtain has to be kept.
The installed position of the air curtain can be chosen to accommodate the service hood.
It must be operated in dry, coverot indoor spaces with an ambient temperature between +5° C and
+40° C and relative humidity up to 80%
The air curtain is not intended for moving air that contains combustible or explosive mixtures, chemical fumes, coarse dust, soot, grease, poisons, infectious germs, etc.
6.1.-2 Clearance distance
100 mm
100 mm
MATERIAL
100 mm
100 mm
MATERIAL
OK
OK
100 mm
500 mm
MATERIAL
OK
100 mm
MATERIAL
OK
500 mm
9
6. INSTALLATION
6.1-3 Measure the installation site
•
•
•
•
•
Only nonflammable materials (those that do not burn, smoulder or carbonise) or fire-resistant materials (those that do not burn, but mainly smoulder, e.g., plaster board) can be kept within 100 mm
in any direction of the air curtain. However, these materials should not block the intake or outlet
openings.
For air curtains with an electric heater, safe distances from building structural surfaces and flammable
objects are as follows:
The safe distance for flammable materials in the direction of the main air flow (i.e., behind the outlet)
is 500 mm,
The safe distance for flammable materials above the air curtain is 500 mm,
The safe distance for flammable materials in other directions is 100 mm.
A
B
OK
OK
Recommended size of ceiling aperture
for inserting the curtain:
A
B
[mm]
[mm]
VCF-X-100-X…
1140
620
VCF-X-150-X…
1640
620
VCF-X-200-X…
2140
620
VCF-X-250-X…
2520
620
Type
•
•
•
•
•
•
Air curtain is fixed to the ceiling by 4 threaded rods, which are not included delivery.
It is necessary to ensure proper in the supply at the site according to the exact type of use of the air
curtain and based on its electric parameters.
When using water heated air curtain, please ensure connection of the flow and return pipes.
It is necessary to cut or otherwise make a hole according to the hereunder mentioned dimensions
Drill four holes into the ceiling construction according to the dimensions scheme (see “Dimensions”)
for hanging of the air curtain to 4 anchoring points.
Screw the air curtain directly to the ceiling without any space between its casing and ceiling, or use
four threaded bars to reach the required distance from the ceiling, according to the situation on the
site (see “Conditions for safety and proper function of the air curtain”).
For wall installation use „Wall mounted bracket set“: VCS4-KONZ-STE. „Wall mounted bracket
SET“ has to be ordered separately as an optional accessorie.
470
10
3x
9
280
220
150
10
40
114
57
38
280
220
150
10
40
114
9
6. INSTALLATION
3x
57
38
L2
M8
M8
L1
M8
M8
For ceiling installation use „Ceiling holder SET”: VCS4-KONZ-STR. „Ceiling holder SET” has to be
ordered separately
as an optional accessorie.
4x
9
40
114
9
15,5
15,5
49
31
95,5
175,5
255,5
Type
L2
L1
302
L1
L2
[mm]
[mm]
VCF-X-100-X…
1085
250
VCF-X-150-X…
1585
250
VCF-X-200-X…
2085
250
VCF-X-250-X…
2465
250
M8
M8
M8
M8
6.1-4 Suspend the air curtain on the threaded bars and ensure that the suspension will not
come loose
•
In consideration of the air curtain weight into account, it is necessary to use either a suitable lifting
device (forklift, etc.) or use two additional individuals to support it, as long as it is not securely fastened.
•
Suspension has to carry the weight of the air curtain!
11
6. INSTALLATION
6.2 CONNECT THE WATER INTAKE AND OUTLET HOSES
VCF-x-xxx-V(W)-...
•
A flexible hoses with a G3/4“ connection
•
Connection and pressure testing of the heater must be carried out by a person with professional
plumbing knowledge, who must observe current standards and regulations of the given country.
The maximum water temperature is +100° C. The maximum pressure is 1.6 MPa. We recommend
installing a stop valve on the intake and outlet of the heater to allow the water supply to be shut off .
•
3/4"
3/4"
6.2-1 Regulating the water coil with a thermostatic valve TV1/1
(Air curtains with water coil and SM control module: VCS-R-SM-V-2)
TV1/1
VCF-x-xxx-V(W)-...
+
VCS-R-SM-V
Thermostatic valve TV1/1 is an required accessorie for control module VCS-R-SM-V-2
12
6. INSTALLATION
•
Detailed description of water coil regulation by thermostatic valve (TV1/1), including it´s connection,
refer the instruction manual for thermostatic valve TV1/1.
6.2-2 Regulating the water coil with a ZV-3 zone valve (Air curtains with water coil and DM
control module: VCS-R-DM-V-2)
Zone valve ZV-3 is an required accessorie for control module VCS-R-DM-V-2
AB
B
A
ZV-3
VCF-x-xxx-V(W)-...
+
VCS-R-DM-V
•
Detailed description of water coil regulation by zone valve (ZV-3), including it´s connection, refer the
instruction manual for zone valve ZV-3.
6.2-3 Regulating the water coil with an mixing valve MV-3 (Air curtains with water coil and
DA control module: VCS-R-DA-V-2)
Mixing valve MV-3 is an required accessorie for control module VCS-R-DA-V-2
AB
A
B
MV-3
VCF-x-xxx-V(W)-...
+
VCS-R-DA-V
•
Detailed description of water coil regulation by mixing valve (MV-3), including it´s connection, refer
the instruction manual for mixing valve MV-3.
13
6. INSTALLATION
6.3 ELECTRO INSTALLATION
•
•
•
•
•
•
•
•
The air curtain’s electrical connection must be based on a professional design by a qualifi ed electrical
systems engineer.
Installation must be carried out by a professionally trained electrical worker. All applicable national
regulations and directives must be observed.
The electrical schematics on the product take priority over those presented in this manual!
Prior to installation, check to see if the terminal markings correspond to the markings on the electrical connections diagram. When in doubt, contact your supplier and do not connect the air curtain
under any circumstances.
Never reach inside the air curtain unless the main electrical supply has been turned off !
If the product is connected to any control system other than the original one, the regulation and measurement components must be connected by the company that supplied the system.
The electrical contractor defines the minimum size of the feed cable according to the standards applicable at the place of installation, the location for installing the cable, the surrounding conditions, and
the curtain‘s technical parameters.
Special attention should be paid to the capacity of the distribution network of the air curtain
with electric heater in terms of the supply of the appropriate phase current values for limiting
the voltage fluctuations and flickering in the network.
Minimal cable dimensions:
14
Fuse specification:
Type
Cable dimention
VCF-x-xxx-S…
3Cx1,5
VCF-x-xxx-V…
3Cx1,5
VCF-x-xxx-W…
3Cx1,5
VCF-x-100-E…
5Cx2,5
VCF-x-150-E…
5Cx4
VCF-x-200-E…
5Cx6
VCF-x-250-E…
5Cx10
x
Typ
VCF-x-xxx…
B
xxx
C
100
3,15A
5A
150
4A
6,3A
200
6,3A
8A
250
8A
12A
6. INSTALLATION
•
The electrical parameters are shown
on the manufacturer‘s label, which is
located under the air curtain‘s service
cover.
Air curtain Type
U = Voltage
f = Frequency
n = Speed
ph = Phase
av = Air output
5x20
250V AC
T xxA
•
•
•
•
L1
L2
L3
N
PE
3~ 400V
L1
L2
L3
N
PE
1~ 230V
L
N
PE
I = Net current
P = Output
m = Weight
IP = IP rating
ver =
Serial number
The air curtain must be pRotected by an appropriate circuit breaker, in accordance with its electrical
parameters. For safety reasons, over-designed protection is not recommended.
The air curtain must be connected using the TN-S system, which means that the neutral conductor
must always be connected.
A main cut-off switch must be placed in the electrical supply network, disconnecting all poles of the
network.
The electrical enclosure of the air curtain is IP 20.
FINESSE air curtains are equipped with a fuse (with T characteristic – slow-blow). This safety fuse pRotects the electronic panel and fans. It is located under the service cover next to the main power supply
connectors.
6. 4 CONTROL MODULES
Air curtains FINESSE are produced with universal connection interface.
Air curtains FINESSE can be controlled by one of following control modules.
Control modules are required accessories and has to be orderot separatelly.
Air curtain is connected with control module by „Quick connection sockets“
15
6. INSTALLATION
6.4-1 Insert control module to the air curtain
6.4-2 SM control module (suitable with all types of air curtains)
Types of SM control modules:
VCS-R-SM-S (Suitable withl types without heating - VCF-x-xxx-S-...)
DK1
DK2
1
2
(WHITE)
X2 (BÍLÁ)
3
4
5
16
6. INSTALLATION
VCS-R-SM-V (Suitable with types with water coil VCF-x-xxx-V(W)-...
DK1
DK2
1
(BLUE)
X3 (MODRÁ)
(WHITE)
X2 (BÍLÁ)
2
3
4
5
VCS-R-SM-E (Suitable with types with electric heater VCF-x-xxx-E-...)
DK1
DK2
X5 (NONE)
(ŽÁDNÁ)
X4 (ČERVENÁ)
(RED)
X3 (BLUE)
(MODRÁ)
X2 (BÍLÁ)
(WHITE)
1
2
3
4
5
6
7
17
6. INSTALLATION
For detailed information of SM control modules installation into FINESSE air curtains read carefully:
QUICK START manual for SM control modules installation (deliverot with control module)
For detailed information of SM control modules operation with FINESSE air curtains read carefully: Full
manual: OPERATION AND MAINTANANCE of FINESSE with SM control module
6.4-2.1 Function overview of SM control modules
With water coil
Air only
With electric heater
(VCF-x-xxx-S-...)
(VCF-x-xxx-E-...)
SM (VCS-R-SM-S)
SM (VCS-R-SM-E)
SM (VCS-R-SM-V)
x
x
x
Water coil regulator
x
x
Door switch
DS
DS
DS
Door contact
x
x
x
Optional
Room thermostat
x
x
x
accessories
Ceiling mounted brackets
VCS4-KONZ-STR.
VCS4-KONZ-STR.
VCS4-KONZ-STR.
Wall mounted brackets
VCS4-KONZ-STE.
VCS4-KONZ-STE.
VCS4-KONZ-STE.
EXIT sign
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
Air curtains execution
Control module
Required
accessories
„External temperature
sensor“
(VCF-x-xxx-V-...,
VCF-C-xxx-W-...)
„TV1/1
(Thermostatic valve)“
With water coil
Air only
With electric heater
(VCF-x-xxx-S-...)
(VCF-x-xxx-E-...)
Control module
SM (VCS-R-SM-S)
SM (VCS-R-SM-E)
SM (VCS-R-SM-V)
Type of control
Manual
Manual
Manual
Air curtains execution
(VCF-x-xxx-V-...,
VCF-C-xxx-W-...)
Speed of the fan
***
***
***
Electric heater regulation
x
2-steps
x
Water heater regulation
x
x
Thermostatic valve
Control panel connection
„Power cable 230V“
„Power cable 230V“
„Power cable 230V“
Number of quick connection
1
4
2
Door switch behavior
ON/OFF
ON/OFF
ON/OFF
Timer
x
x
x
Temperature measurement
x
x
x
Operation state indication
x
x
x
Radio signal indication
x
x
x
Cleaning interval indication
x
x
x
Water heater anti-frezze protection
x
x
x
Aftercooling of electric heater
x
x
x
Chaining of the air curtains
x
x
x
sockets
18
6. INSTALLATION
6.4-3 DM control module (suitable with all types of air curtains))
Types of DM control modules:
VCS-R-DM-S (Suitable with all types without heating - VCF-x-xxx-S-...)
ON
OFF
DK
RF
1
2
3
DK
(WHITE)
X2 (BÍLÁ)
VCS-R-DM-V (Suitable with all types with water coil VCF-x-xxx-V(W)-...)
ON
DK
(BLUE)
X3 (MODRÁ)
(WHITE)
X2 (BÍLÁ)
OFF
RF
0
1
1
2
3
DK
VCS-R-DM-E (Suitable with types with electric heater VCF-x-xxx-E-...)
ON
X5 (NONE)
(ŽÁDNÁ)
X4 (RED)
(ČERVENÁ)
X3 (BLUE)
(MODRÁ)
X2 (WHITE)
(BÍLÁ)
DK
OFF
RF
0
1
2
1
2
3
DK
For detailed information of DM control modules installation into FINESSE air curtains read carefully:
QUICK START manual for DM control modules installation (deliverot with control module)
For detailed information of DM control modules operation with FINESSE air curtains read carefully: Full
manual: OPERATION AND MAINTANANCE of FINESSE with DM control module
19
6. INSTALLATION
6.4-3.1 Function overview of DM control modules
With electric heater
(VCF-x-xxx-S-...)
(VCF-x-xxx-E-...)
DM (VCS-R-DM-S)
DM (VCS-R-DM-E)
DM (VCS-R-DM-V)
x
x
x
x
x
Door switch
x
x
Air curtains execution
Control module
„External temperature
Required
sensor“
accessories
Water coil regulator
Optional
accessories
With water coil
Air only
(VCF-x-xxx-V-...,
VCF-C-xxx-W-...)
“ZV3
(Zone valve)“
x
Door contact
DK-1
DK-1
DK-1
Room thermostat
x
x
TER-P
Ceiling mounted brackets
VCS4-KONZ-STR.
VCS4-KONZ-STR.
VCS4-KONZ-STR.
Wall mounted brackets
VCS4-KONZ-STE.
VCS4-KONZ-STE.
VCS4-KONZ-STE.
EXIT sign
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
•
•
20
With water coil
Air only
With electric heater
(VCF-x-xxx-S-...)
(VCF-x-xxx-E-...)
Control module
DM (VCS-R-DM-S)
DM (VCS-R-DM-E)
DM (VCS-R-DM-V)
Type of control
Manual
Manual
Manual
Air curtains execution
(VCF-x-xxx-V-...,
VCF-C-xxx-W-...)
Speed of the fan
***
***
***
Electric heater regulation
x
2-steps
x
Water heater regulation
x
x
Zone valve
Control panel connection
Radio signal
Radio signal
Radio signal
Number of quick connection sockets
1
4
2
Door switch behavior
ON/OFF
ON/OFF
ON/OFF
Timer
x
x
x
Temperature measurement
x
x
Room thermostat
Operation state indication
LED
LED
LED
Radio signal indication
LED/BEEP sound
LED/BEEP sound
LED/BEEP sound
Cleaning interval indication
x
x
x
Water heater anti-frezze protection
x
x
x
Aftercooling of electric heater
x
30 s
x
Chaining of the air curtains
In radio signal range
In radio signal range
In radio signal range
Air curtains can be connected by chaining with up to a maximum of 6 pieces.
The distance between first and last curtain should be a maximum of 40 metres.
6. INSTALLATION
6.4-4 DA control module (suitable with air curtains with water or electric heater)
Types of control modules:
VCS-R-DA-V (Suitable with all types with water coil VCF-x-xxx-V(W)-...)
X3 (BLUE)
(MODRÁ)
X2 (WHITE)
(BÍLÁ)
23
24
Run
signalization
Run signalization
Signalizace
běhu
23
24
External
temp.teploty"
sensor
External
temp.
sensor
"Čidlo externí
27
28
DK
29
30
EXT
Esc
Auto
Man
SET TIME
CLEAN RESET
SET TIME SWITCH
VCS-R-DA-E (Suitable with types with electric heater VCF-x-xxx-E-...)
X5 (NONE)
(ŽÁDNÁ)
X4 (ČERVENÁ)
(RED)
X3 (BLUE)
(MODRÁ)
X2 (WHITE)
(BÍLÁ)
23
24
Run
signalization
Signalizace
běhu
Run signalization
23
24
"Čidlo externí
External
temp. teploty"
sensor
External
temp.
sensor
27
28
DK
29
30
EXT
Esc
Auto
Man
SET TIME
CLEAN RESET
SET TIME SWITCH
For detailed information of DA control modules installation into FINESSE air curtains read carefully:
QUICK START manual for DA control modules installation (deliverot with control module)
For detailed information of DA control modules operation with FINESSE air curtains read carefully: Full
manual: OPERATION AND MAINTANANCE of FINESSE with DA control module
21
6. INSTALLATION
6.4-4.1 Function overview of DA control modules
Air curtains execution
Control module
Required
accessories
Optional
accessories
„External temperature
With electric heater
(VCF-x-xxx-E-...)
With water coil
(VCF-x-xxx-V-...,
VCF-C-xxx-W-...)
DA(VCS-R-DA-E)
DA(VCS-R-DA-V)
„Included with
„Included with
sensor“
control module“
control module“
Water coil regulator
x
Door switch
x
x
„MV-3
(Mixing valve)“
Door contact
DK-1
DK-1
Room thermostat
x
x
Ceiling mounted brackets
VCS4-KONZ-STR.
VCS4-KONZ-STR.
Wall mounted brackets
VCS4-KONZ-STE.
VCS4-KONZ-STE.
EXIT sign
VCS4-EXIT
VCS4-EXIT
Air curtains execution
22
(VCF-x-xxx-E-...)
With water coil
(VCF-x-xxx-V-...,
VCF-C-xxx-W-...)
Control module
DA(VCS-R-DA-E)
DA(VCS-R-DA-V)
Type of control
Manual/Automatic
Manual/Automatic
Speed of the fan
***
***
Electric heater regulation
3 steps / Fluently
x
Water heater regulation
x
Mixing valve
Control panel connection
Radio signal
Radio signal
Number of quick connection sockets
4
2
Door switch behavior
OFF/1st speed / 2nd speed
OFF/1st speed / 2nd speed
Timer
Day/ Week
Day/ Week
„2 internal sensors
„2 internal sensors
1 external sensor“
1 external sensor“
Temperature measurement
•
•
With electric heater
Operation state indication
LCD
LCD
Radio signal indication
BEEP sound
BEEP sound
Cleaning interval indication
Time interval
Time interval
Water heater anti-frezze protection
x
Automatic
Aftercooling of electric heater
30s/1min
x
Chaining of the air curtains
In radio signal range
In radio signal range
Air curtains can be connected by chaining with up to a maximum of 6 pieces.
The distance between first and last curtain should be a maximum of 40 metres.
6. INSTALLATION
6.5 CONNECT THE EXTERNAL ACCESSORIES
Accessories overview
Required accessories
Air curtains execution
Control module
Optional
accessories
With electric heater
(VCF-x-xxx-E-...)
temperature
With water coil
(VCF-x-xxx-V-..., VCF-C-xxx-W-...)
SM(VCS-R-SM-S)
DM(VCS-R-DM-S)
SM(VCS-R-SM-E)
DM(VCS-R-DM-E)
DA(VCS-R-DA-E)
SM(VCS-R-SM-V)
DM(VCS-R-DM-V)
DA(VCS-R-DA-V
x
x
x
x
„Included
with
control
module“
x
x
„Included
with
control
module“
x
x
x
x
x
„TV1/1
Thermostatic
valve)“
„ZV-3
(Zone
valve)“
„MV-3
(Mixing
valve)“
„External
sensor“
Water coil regulator
Door switch
DS
x
DS
x
x
DS
x
x
Door contact
x
DK-1
x
DK-1
DK-1
x
DK-1
DK-1
Room thermostat
Ceiling mounted brackets
Wall mounted brackets
EXIT sign
•
•
Air only
(VCF-x-xxx-S-...)
x
x
x
x
x
x
x
x
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
-STR.
-STR.
-STR.
-STR.
-STR.
-STR.
-STR.
-STR.
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
VCS4-KONZ-
-STE.
-STE.
-STE.
-STE.
-STE.
-STE.
-STE.
-STE.
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
VCS4-EXIT
When connecting external components, the electricity to the air curtain must be turned off .
All external control components must be connected according to the electrical schematic. The connectors must be connected to the electrical board using reasonable force and always vertically to
the base.
6.5-1 Door contact DK
Headerrozdělovače
Connector
Konektor
- Isolated switching contact with a maximum voltage of 12V.
Cable - Dual-core cable with a diameter of 0.5 mm. - Maximum length: 50 m.
For DM and DA control modules only!
27 28
Connectors on the DM control modules: DK/DK
Connectors on the DA control modules: 27/28
Not included in delivery.
23
6. INSTALLATION
6.5-2 Door switch DS
- Isolated switching contact with a maximum voltage of
230V. Cable - Dual-core cable with a diameter of 1.5 mm.
- Maximum length: 50 m..
For SM control modules only!
Connectors on the SM control modules: DK1/DK2
Not included in delivery.
6.5-3 External temperature sensor
°C
OUTSIDE
25 26
- Thermally-dependent resistive sensor
For DA control modules only!
Connectors on the DA control modules: 25/26
Included in delivery with VCS-R-DA-x
6.5-4 Zone valve ZV-3
- Zone valve for water heater regulation
- Cable – Three core cable with diameter of 1,5 mm,
230 V/ 50 Hz.
For VCS-R-DM-V control modules only!
Connectors on the DM control modules: 1 /4 /5
Not included in delivery.
24
6. INSTALLATION
6.5-5 Room thermostat TER-P
- Room thermostat for water coil regulation
- Cable – Two core cable with diameter of 1,5 mm,
230 V/ 50 Hz.
For VCS-R-DM-V control module only!
Connectors on the DM control modules: 2 / 3
Not included in delivery.
6.5-6 Mixing valve MV-3
- Mixing valve for water heater regulation
- Cable – Three core cable with diameter of 1,5 mm,
230 V/ 50 Hz.
For VCS-R-DA-V control modules only!
Connectors on the DA control modules: 3 /4 /5
Not included in delivery.
6.5-7 Thermostatic valve TV1/1
- Thermostatic valve for water heater regulation
For VCS-R-SM-V control modules only!
Connectors on the SM control module: NOT CONNECTED!
Not included in delivery.
25
6. INSTALLATION
6.5-8 Exit sign
EXIT
- Exit sign marking of emergency exit
For all types of VCS4x- air curtains!
Not included in delivery.
EXIT
6.6 COVERING THE AIR CURTAIN
26
7. INITIAL START-UP
Before putting the curtain into operation, check the following:
• Have any tools or other objects which could damage the curtain been left inside it?
• Is there a proper supply of electricity and, if necessary, heating water?
• Has the air curtain been properly closed?
• Has the control module been connected properly?
Before putting the curtain into operation, read carefully:
Full manual for OPERATION AND MAINTENANCE (deliverot with control module)
7.1 SET AIR FLOW DIRECTION
This is set by tilting the air curtain’s fan louvers in the desirot direction.
.
8. CONCLUSION
If you have any doubts or questions, do not hesitate to contact our sales or technical support department.
Before operation and maintanance, thoroughly read the section “Safe use of air curtains”. It contains
all instructions on the safe and correct use of the product.
27
9. CONTACT
CONTACT
Adresse
2VV, s.r.o.,
Poděbradská 289,
530 09 Pardubice,
Czech Republic
Internet
http://www.2vv.cz/contact.distribution.php
28
29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement