Solidstone Shower Tray Installation

P-IMP-MAN-111 EsGb 1111-7L
Installer´s Guide
BAÑOS 10 S.L.
CTRA VILA-REAL - ONDA KM 12,6
12200 ONDA
11
UNE-EN 14527:2006
Platos de ducha de uso doméstico
So
lids
Tra ton
y In e S
Co
h
s
mp
t
o
a
we
Fo act /
l
l
res Na
a
t
t/
r
i
Co tural
o
mp / Ir
n
lex on
NºGarantia / Guaranteen Number :
GB
INDEX
1- GENERAL CONDITIONS
2- GUARANTEE
3- PRODUCT FEATURES
4- SUPPLIED ELEMENTS
5- REQUIRED ELEMENTS FOR INSTALLATION
6- SHOWER-TRAY PRE-INSTALLATION
7- THINGS TO TAKE CONSIDERED BEFORE INSTALLATION
8- OPTIONS OF INSTALLATION
9- SHOWER-TRAY INSTALLATION
10- HOW TO CUT THE SHOWER-TRAY
11- CLEANING, MAINTENANCE AND DURABILITY
1
GENERAL CONDITIONS
Baños10 thanks you for acquiring
a Solidstone shower-tray.
The Solidstone shower-trays are manufacturated with a high
resistance material (impact resistance similar to any stone) and a
minimum absorption (0,01%). The shower-trays are nonsliding and are
treated to avoid the proliferation of bacterians.
All our products have been manufactured with a strictly quality
control.
Baños 10 guarantees their products and components against any
lack of conformity when the use of them and installation have been
made correctly.The company won´t be responsible of the inconveniences
caused by an incorrect or inadequate use of the products, so guarantee
will never cover the expenses of substitution of shower screens, tile or
whatever element that should be replaced by a wrong use or bad
installation.
For a correct installation, use and good maintenance read carrefully
this guide.
GENERAL SCOPE
Baños 10, S.L. guarantees, as manufacturer to the buyer and/or user all
rights under the law 23/2003 of July 10, in consumer goods sales.
It also guarantees to the buyer and/or user of the device whose data is
contained in the Warranty Document, repair the equipment if it has sustained
damage due to a defect in material or workmanship, provided it is intended
for private use and that has been handled properly and in accordance with
instructions for assembly, connection, commissioning and management.
These repairs will be free including the cost of spare parts, works and
displacement of technical staff to the user address presenting purchase
documents and guarantee.
This warranty applies to the minimum guarantee that we offer as a producer.
IMPORTANT
To qualify for this guarantee, is essential to demonstrate to Baños 10 Official
Service the date of product receipt. For this, it is only necessary to show
the INVOICE, receipt or the delivery note whichever is later of invoice or
receipt date.
So, keep your invoice or sales receipt attached with this document.
TERMS AND CONDITIONS
2
GUARANTEE
Dear Customer,
From Baños 10 we thank you for the confidence placed in us by purchasing
one of our products and hope to provide an excellent service for many
years.
As manufacturers and makers of the product you purchased, we are
convinced of the excellent quality of it, and hope it does not need any
technical intervention for a long time. However, if you require a visit or
advice from our service center, both inside and outside the warranty period,
we are available on the phone 902 360 708. Also, for any product-related
query, please contact us by phone or email at sat@banos10.com.
The deadline for claiming the conformity by the consumer is 24 months from
the delivery time. In case of non-conformity, the consumer may choose
between repair or replacement unless it is impossible or disproportionate.
The deadline to inform Baños 10, SL any non-compliance is two months
since the buyer or user had knowledge about it.
This warranty extends to the purchaser or user, provided it is duly supported
by original invoice or sales receipt and delivery note. Read the user manual
before using the product. Consult your doctor or specialist whether or not
to use. Do not let children use it without adult supervision
EXCLUSION OF WARRANTIES
Warranty excludes damage caused by malfunctions caused as a result of:
• Damage during transportation and / or handling the installation.
• Force majeure for all atmospheric or geological.
• Deficiency of electrical supply either by excess or defect.
• Chemical or electrochemical reactions, in combination with the material
and / or water, such as those caused by spilled liquids or materials on the
product, water hardness and / or excess of lime, excess humidity.
• Improper installation, not in accordance with local regulations and the
manual supplied with the right editor.
• intervention or manipulation by unauthorized staff or not covered by the
Official Service Baños 10, S.L., even such intervention is or has been only
partial.
• Damage caused by electrical work, plumbing, masonry, carpentry, etc.,
Made to install the device in user's home.
• Handling of information contained in an invoice, purchase receipt or other
document of the warranty.
• Usa not in accordance with the instructions from manufacturer or unrelated
to the purpose of the product.
• Abnormal use of the product in general.
Baños 10, S.L. recommends the installation of their products once tiled and
paved the places of location of the goods supplied, to facilitate maintenance
thereof, except for those where it is necessary for the subsequent installation
of equipment or products.
These conditions apply to products purchased in Spain. These guarantee
conditions also apply to products taken out of Spain, if they have the technical
requirements (such as voltage, frequency, etc.) of country concerned and
where Baños 10, S.L. has an authorized service center in the country. For
products purchased outside of Spain will apply the warranty issued by our
distributor in the country concerned.
TECHNICAL SUPPORT ( SAT.) BAÑOS 10 TEL. 902 360 708 FAX 964 626 415
E-mail sat@banos10.com
3
PRODUCT FEATURES
The Warranty does not cover regular maintenance of the product such as
general cleaning and all those cracks resulting from improper use or forced
use of the product components.
COMPACT
The warranty DOES NOT cover labor costs resulting from the withdrawal
of the product for repairing and / or maintenance.
700-1000
800-2100
4
COMPLEX
SUPPLIED ELEMENTS
2
1
900-1400
700-800
dry
ing
are
a
FOREST
(3 Only in IRON, FOREST and NATURAL) (4 Only in IRON and FOREST)
3
4
700-1000
800-2100
5
NATURAL / IRON
700-1000
800-1950
NOTE: Solidstone range has a tolerance between+- 2,5mm.
REQUIRED ELEMENTS FOR INSTALLATION
E
ON
C
LI
SI
EX
FL
KA
I
S
0
10
ge
n
ra
SHOWER-TRAY PRE-INSTALLATION
7
COMPACT / NATURAL / IRON / FOREST
THINGS TO TAKE IN MIND BEFORE
INSTALLATION
Aspects to be considered before installing the shoer-tray:
- The shower-tray has to drainage correctly.
430
100
30
0 90
Lowering house
(Under the shower-tray)
WARNING: In case of detection of abnormalities or deficiencies
DON´T INSTALL and contact the distributor to inform about the
situation.
250
drying
area
700-1000
- Keep the shower-tray in horizontal position and over plain surface to
prevent malformations until installs it.
- The shower-tray has to be whithout any imperfections or damages to
be installed.
800-2100
250
Hole for drain
COMPLEX
430
100
50
0 90
Lowering house
(Under the shower-tray)
900-1400
250
700-800
6
250
Hole for drain
NOTE: All our Solidstone shower-trays are designed with a ligth
inclination (not normalized) from 1400 where starts the drying area.
8
OPTIONS OF INSTALLATION
9
SHOWER-TRAY INSTALLATION
9.0: Shower-tray preparation.
BUILT IN
For a perfect installation of the Solidstone shower-tray sand the inferior
surface for acquiring porosity so then it can be hold easier.
9.1: Base preparation.
100
For a perfect installation of the
shower-tray the floor must be PERFECTLY
LEVELED and dry. The concrete has to be
completely dry because it could bend the
shower-tray if wet. If it happens, the
shower-tray could be useless.
Wall
Wall-Tiles
The base must be ready with
concrete and never with sand.
ON THE FLOOR
A hole must be made on the
floor in order to set the drain pipe (see
Concrete
the installation). You have to do also a
hole or channel on the floor to pass
the pipes from lowering house till the drain pipe of the shower-tray.
100
9.2: Assembly of the drain pipe.
Put the drain pipe on the floor in its definitive position. Connect
it with the lowering house. Read the instructions of the drain pipe.
ON HIGH
Check that drain-pipe doesn´t leak and all elements don´t
stand out of the holes because the shower-tray wouldn´t seat correctly.
NOTE: It´s very important to get a slope from the drain pipe to
the lowering house to guarantee the drainage.
9.3: Setting of shower-tray.
Take out the shower-tray from the packaging,use the cardboard
to protect the shower-tray during the installation.
NOTE: On high installation the shower-tray has to be installed on a leveled
and smooth surface too. This surface has to cover all surface of the
shower-tray.
Put around the shower-tray a waterproof tape between the wall and the
shower-tray. It will prevent that the water takes out from the shower-tray.
Put on the concrete´s base some fragments of poliuretan mastic
(SICAFLEX / CEYS) to fix the shower-tray.
NOTE: Don´t put the shower-tray more than 10mm. inside the wall
between both sides. In this case, we will avoid problems with the
shower-screen.
Adjust the shower-tray, check that it is leveled (in the lurching
and tilting directions) and that it works correctly.
Take out the cardboard protector, silicone around the shower-tray
with neutral silicon (non acetic) and clean the silicon rests.
Once the shower-tray is in the right position, put the grill (only in Natural,
Iron y Forest ranges) and the screw (only in Iron and Forest shower-trays).
SIK
AFL
EX
rang
e 10
0
The shower-tray has to be fixed and leveled, otherwise the screen´s
doors won´t slide properly.
You can use the shower-tray one day after installation, when silicone
gets totally dried.
Waterproof tape
Check that the shower-tray is installed and works correctly before
tiling the rest of the bathroom.
Put the shower-tray in the definitive place. Coincidy the showertray´s hole with the drains previosly placed.
CEMENT
Wall
Wall-Tiles
WALL-TILES
10 mm
BLOCK
E
ON
LIC
SI
SHOWER-TRAY
Máx. 10 mm
Máx. 10 mm
STUFFING
00
14
WATERPROOF
TAPE
Lurching
direction
Tilting
direction
10
* Shower-trays, but complex, whose measure are
shorter than 1000:
HOW TO CUT THE SHOWER-TRAY
10.1: Protect the zone to cut.
The shower-trays whose measure are shorter than 1000 mm.
have to be installed with their "cut" part built-in the wall. Otherwise the shower
screen couldn´t be installed (see the drawing).
"Cut" part
430
30
100
Measure shorter than 1000:
10.2: Mark with a pencil the cut line.
00
10
0
43
10.3: Cut the shower-tray with a diamond´s cut tool .
Measure longer than 1000:
0
43
00
10
NOTE: The cutt parts have to be inserted into the wall.
11
CLEANING, MAINTENANCE AND
DURABILITY
If concrete or some other materials are in contact with the
shower-tray, use appropiated products to clean the joints. Avoid to rub
directly.
For usual cleaning is enough to wash out with water and dry off.
For an exhaustive cleaning use a soft cloth with neutral liquid not
abrasive. In case of dirtiness or calcareous silt, clean with soap water
or anti-lime product. Rinse with tepid water and dry off.
The Solidstone shower-trays don´t need any specific maintenance.
In this following chart we specify the results of durability caused by
the frequent chemical agents used in the bathroom.
DOMESTIC AGENTS
Bleach
"Salfumán"
"Don Limpio"
"Viakal"
Vinegar
Ammonia
"KH-7"
"Cilit Bang"
Acetone
Isopropanol
Tint of dark hair
Tint of normal hair
Lacquer of dark nails
Lacquer of clear nails
Oxygenated water
"Betadine"
DEGRADATION
24h
4h
24h
24h
24h
24h
24h
24h
1min.
5min.
5min.
5min.
5min.
1h
24h
1min.
(5)
(1)
(3)
(4+)
(2)
(4)
(5)
(5)
(1)
(5)
(2)
(2)
(3)
(5)
(3)
(3)
EVALUATION
01234-
Attacked film.
Superficial degradation and/or formation of blisters
Important change of brightness and/or color
Moderated change of brightness and/or color
Slight change of brightness and/or color, only
visible from certain inspection.
5- Without evident changes
Download PDF