TFT Fingerprint V6.3
TFT Fingerprint V6.3
Important Notes
This fingerprint machine is designed to work with the newly issued
V3.X version Time & Attendance software only, which is completely
compatible with the original V2.X version that has been popularly
applied to all machines, the new one own stronger function, more
convenient, and more human nature for user than the V2.X version
TFT Fingerprint V6.3
Customer Advice
Thank you for purchasing our product. Before using this machine,
please read this manual carefully.
Notice
Please do not place the product in the place with strong light,
because the strong light may significantly affect the fingerprint
scanning, and thus cause the fingerprint verification fail. This
product is designed for indoor installation, if it has to be installed it
outdoor, please place the equipment in proper environment. You
must beware of not exposing it to wet or harsh state, the product
work temperature rang is 0-40℃. Do not use your machine
exceeding this range, keep your equipment away from the heat
source and radiator. For long time use it outdoor and the internal
heat of the machine, will cause problem to the operation.
Please keep it away from violent collision, which would cause the
internal components loosened or damaged. And the equipment is
not a waterproof; Do not place this equipment in wet or damp.
Please use the equipment as the notice, you will get good effect and
test speed.
Notice: Fingerprint Enrollment and Identification shall be taken
after the installation the fingerprint identification machine
TFT Fingerprint V6.3
Installation
Enrollment
Enrollment
Installation
Identification
Identification
How to place the finger
Make sure the fingerprint image captured is of a core of presented
finger, a fingerprint is point to locate within innermost recurring
ridge of any give finger.
To obtain a higher success rate, enroll same finger 3 times in a
slightly-adjusted angle, one to the center, one incline slightly to the
left. The third incline slightly to the right. Please follow the place
procedure; the success rate will increase dramatically.
The correct way is:
Place a finger flatware on the sensor surface
Place it to the center of the sensor surface
The wrong way is
TFT Fingerprint V6.3
Notice: Please adopt the correct way to place the finger. Our
Company is not responsible for any damages and troubles
whatsoever arising out of from improper pressing manner.
About this Manual
All functions in this document are subjected to the actual product ,
as a result of the product is unceasing renewal, all attempts have
been made to make the information in this document complete and
accurate. Our company is not responsible for the actual product is
consistent with this material, is not responsible for any direct or
indirect damage or loss of business resulting from inaccuracies or
omissions, the specifications in this document are subjected to
change without notice
TFT Fingerprint V6.3
About 8〞TFT iClock
1
4
2
5
3
6
7
8
9
10
13
14
15
11
12
TFT Fingerprint V6.3
16、Battery Box
17、SD card Slot
1 LED indicators: at normal working the green light blinking per one
second, if the verification is positive, the LED will glow green for long
-three seconds, If the authentication fails ,the LED glow red for
long-three seconds.
2 Function keys: state key and functional shortcuts.
3 Small keyboards: to key in Chinese characters, letters, numbers, etc.,
and the menu operation.
4Camera: take a photo when user go on authorization
5.Touch Screen: display the operation result
6 Joystick key: locate various options by right, left, above, under
position.
7 Fingerprint Sensor:
match with the fingerprint.
8 Audio jacks: External speaker box.
TFT Fingerprint V6.3
9 RS232/485 port: RS232/485 communications between the equipment
and the computer
10 USB port: for external USB devices (such as u disk, fingerprint
sensor).
11 RJ45 port: for and computer network connections.
12 Power outlet: Access for power.
13 USB port: for external USB devices (such as flash disk, fingerprints
sensor).
14 Reset key : when the machine is in halt, push this key with small
tools
15 Key hole:
Lock the when cover of the Cable Box
16 Battery box: It is used to install backup battery along with machine.
17 SD card slot: Plug SD card into here.
About battery
To help avoid possible damage to the equipment by accidentally shut
down and better ensure the track staff attendance, the device provides a
backup battery, in the accident the battery power will provide the
equipment.
Battery installation
Before installing the equipment, make sure that the battery are correctly
load in.
1, screw off two screws and open the battery box.
2, open the back plate of the battery box, load into the battery, and
ensure the battery with copper side forward down.
3, after fully loaded, mount the back plate, use the two screws fasten it.
TFT Fingerprint V6.3
Battery dismantle
When the equipment is in the process of long-term transport or without
use, it better to take out the battery and place it in dry, cool place,
otherwise, the battery may be rusty or enable machine poor performance.
1. After taking way the two screws of the battery box.
2. Open the back plate of the battery box, took out the battery.
3. Mount on the back, fastening on the two screws.
Installation Steps
1) Mount the metal plate on walls in the appropriate place and fix it.
2 Find the key along with the product. Open cover of the cable box
3) Connect the cable with machine, make sure that the wired machine
align with the plate , then hang it on the plate and fix machine with
screws below.
4) Arrange the machine’s vertical edge so that they are in line with edge
of the cover of the cable box, alignment, hold the machine bottom, and
after in accordance with gently push the cover toward the vertical
direction, shown as ②arrowhead.
5) Push the cover until it is parallel with the bottom of machine, and
then push lightly the cover toward the right level until the cover
completely meet with the machines.
6) Use the Key locks the cover
TFT Fingerprint V6.3
Recommendation step
Step1: Place the fingerprint machine properly and power up machine.
Step2: Enroll user, register fingerprint and password, and assign
privilege to user.
Step3: verify user by the registered fingerprint and password.
Step4: Configure the communication parameter; download the staff
information to software using the U flash disk or one of three
communications which is used to connect with the computer.
Step5: Revise the staff’s information in the staff maintenances item of
software, connect the equipment with PC again and upload the staff
information to the equipment. At this time when the fingerprint machine
track staff’s Time & Attendance log , his/her name will be display on the
screen.
Step6: Check the fingerprint machine time, and make sure whether it
is correct, after completing setting up, then start to track employee’s
attendance.
Step7: At the end of the month the downloaded attendance log to
software will be calculated.
TFT Fingerprint V6.3
About Play Flash
To play flash is available for this device, after loading the flash file
into machines, the device is able to play flash in the ready state, so it can
produce some publicity flash and upload it into the machine to play.
Ready work:
The ready work equipment as shown below:
Standby state is shown in photographs, users can upload images (see
7.4 upload custom photo), but also can shift the clock displayed on the
screen intermediate (See 5.1 interface installed).
When the equipment in ready working mode, users press OK button or
touch keys on the screen after the player launched flash player, the
middle of the screen broadcast flash animation.
TFT Fingerprint V6.3
After playing the flash, the player interface will automatically shut
down, in the process if press any button to stop players and return
to the standby mode.
Touch Screen
The devices support touch screen. That is, if we perform an
operation without keyboard by pressing option , it is only need to
use the touch pen or fingers, such as touch the icon or menu ,
according to the location or menu the system will locate and input
information, this can be user-friendly operation.
For example: now users attempt to enter the menu for operation.
Instructions
There are two methods can be used,
into the menu.
The First: Pressing
The second: finger touch the icon regional of Menu on the screen
About Time &Attendance
When the equipment in ready work mode, users verification is
positive by the fingerprint or password, whose attendance record
will be tracked by the machines and the records will be saved.
How to choose the Attendance state
The equipment is in ready mode, press the function key of the
equipment around both sides of the screen to shift attendance state
and the state button corresponding state information is displayed on
the screen, the current selected state glow in orange highlights.
TFT Fingerprint V6.3
After 8 seconds showing, press the "ESC" key the messages will
disappear.
Touch the display area on screen lower right of the key
corresponding state information can be displayed once again. (See
definition of state 5.5 keyboard definitions)
Track Staff Attendance
When staff punch –in or out, who will be more concerned about the
current perform time, and so after staff in attendance the equipment will
show the current time on the screen by clocks.
u
Time &Attendance by Fingerprint
The attendance record will be unable to be saved to the machine unless
user verifies successfully with her/his the fingerprint or the password.
TFT Fingerprint V6.3
(1)1: N fingerprint validation
Match the fingerprint which is created by user press finger on the
sensor face and all fingerprints data in fingerprint machine
Step1: Press the fingerprint sensor with finger in proper method.
Step2: The equipment prompts "Thanks", the validation is
successful. If the user’s photo has been registered, the photo will
appear
TFT Fingerprint V6.3
The equipment prompt "please place finger again ", go back to
repeat operation.
TFT Fingerprint V6.3
(2)1: 1 fingerprint validation (ID.NO +fingerprint)
Match the fingerprint which place the fingerprint sensor face and
entry the related number with keyboard, when user's fingerprint
quality is too poor to be recognized, this way 1: 1 will be available.
Step 1: Verify personnel's ID.NO that keyboard entry in the initial
interface.
Step 2: Place finger on the sensor window in proper way
Step3: The equipment prompt "error enrolled ID", Means the
number does not exist
TFT Fingerprint V6.3
Step 4: The equipment prompt "Thanks", the validation is successful.
When the prompt “please try again” appear.
TFT Fingerprint V6.3
In the equipment there are default two times to allow the staff to try,
Times range is set in 5.1 interface. After failing to verify two times,
the user must return the step to operate again.
u
Track Time & Attendance by password
Step 1: Type personel’s ID.NO to be verified in the initial
interface, press "OK" key
Step 2: If prompt the registered number is wrong, that means there
is no the personnel's number; or the staff has not registered the
password.
TFT Fingerprint V6.3
Step 3: the password interface appears, please input the password
Step 4: The equipment prompt "Thanks", the validation is successful.
TFT Fingerprint V6.3
The equipment prompts "the password is wrong", the interface will
return to the password operation interface.
TFT Fingerprint V6.3
In the equipment there are default two times allowing the staffs to
try, the number of times to be allowed to set in5.1 interface. After
failing to verify two times, the user must return the step to operate
again
u
Track Time & Attendance by Card
Step 1: slight wave the cards near the induction area, after the
equipment found the card, then remove the card from the
equipment.
Step 2: When the equipment prompt “Thank you” appear, then the
verification is completed”, if users’ photo has been registered.
Step 3: If the cards have not been registered yet, mention that card is
unregistered
TFT Fingerprint V6.3
Note: the card induction area is 3cm -7cm above the small keyboard.
About Access Control
After complete to assign the Access Control privilege, when the
staff verify he/she identity on the equipment, the equipment will
determine staff whether own privilege to open the door. If
employees fail to unlock cause from he/she do not meet the defined
conditions, the equipment will be given corresponding prompt, the
following take fingerprints to verify as an example:
1. Equipment prompt that verification is successful, and sent a
unlock signal.
TFT Fingerprint V6.3
2.
The equipment prompt the Time Period is invalid.
TFT Fingerprint V6.3
This current time is without the Time Period employees is allowed
to open the door. Therefore, the staff could not open the door.
3. Prompt the invalid Group combine appear by the equipment
This group the staff locates without unlocking combine. Therefore,
the staff could not open the door.
4. Motion to go on multi-user certification.
TFT Fingerprint V6.3
Until the group where user locates and the other group pass
certification together, it is not allowed to open the door.
5.The equipment motion to combination verification.
TFT Fingerprint V6.3
This is verification through the user or the group, the users locate
combine verified, it is need to verify identity by multiple
verification
Connect with PC
This equipment will only track the attendance time record, but to
get statistics result is unavailable till the software process the
attendance record in the PC, therefore connecting machine with PC
is necessary download attendance logs into Time & Attendance
tracking software. There are some ports that support kinds of
communications between machine and Time& Attendance tracking
software:
u
Ethernet
(1) Via the Hub: With Straight Thru Cable (apply to connect
TFT Fingerprint V6.3
network card and Hub) turns on, connect fingerprint machine to
network.
(2)directly Connection: With T crossover cable(directly
connect two Ethernet terminal)connect fingerprint machine to PC
Machine Option: Enters the menu - communication Option, please
set the following several items:
IP address: default IP is 192.168.1.201, which has to be resetted.
Subnet mask: default Subnet mask is 255.255.255.0, you may change
it depending on actual application.
Gateway: the default gateway is 0.0.0.0, you may change it
depending on actual application
Network speed: In network running speed, there are Automatic
Adaptation, 10M and 100M, three options;
Connection password: in the Connection Setting. May change
communication parameter, after setting, input the corresponding value
on connection interface in the PC software.
u
RS232 way
Machine setting: Enter the menu - communication option, please set
the following several items:
Baud rate: With the computer communication speed, the high speed
communication is quick, it is better to use the RS232 communication;
(115,200, 57,600).
RS232: Whether uses the RS232 communication, set this item as
TFT Fingerprint V6.3
“Yes”
Communication password: in the “connection setting". May change
communication parameter, after setting, must input the corresponding
value on connection interface in the PC
u
RS485 way
Machine Setting: Enter the Menu – Communication option, please
set the following items:
Serial number: Assign a network ID. The serial number scope is 1
– 254.
Baud rate: the computer communication speed, the low speed
communication is stable; we recommend that the RS485
communication Baud rate as 9,600 and 38,400.
If use RS485 to communicate, please set this item as “Yes”.
RS485: Communication password: in Connection Setting. After the
password was set the corresponding value must be input on
connection interface in PC.
TFT Fingerprint V6.3
Content
1 Main Windows ................................................................................................. 1
2 User Management ............................................................................................ 3
2.1 Add new user.............................................................................................. 3
2.2 View User................................................................................................. 12
2.3 card management ★ ................................................................................. 22
2.4 work codes★ ........................................................................................... 32
2.5 Access Control setting ★.......................................................................... 35
3 System Setting................................................................................................ 52
3.1 Systems parameters................................................................................... 52
3.2 Time and Date settings.............................................................................. 56
3.3 Data managements.................................................................................... 59
3.4 Upgrade firmware..................................................................................... 61
3.5 Restore Setting ......................................................................................... 62
3.6 Automatically test ..................................................................................... 63
4 Communication setting .................................................................................. 67
4.1 Communication setting ............................................................................. 67
4.2 Remote verification ★.............................................................................. 70
4.3 Wireless settings★ ................................................................................... 74
4.4 Available wireless network★ .................................................................... 76
4.5 dial-up settings★...................................................................................... 77
4.6 Wiegand input settings ★ ......................................................................... 83
4.7 Wiegand output settings ★ ....................................................................... 84
4.8 Print Settings ★ ....................................................................................... 87
5 User profile..................................................................................................... 90
TFT Fingerprint V6.3
5.1 User Customize ........................................................................................ 90
5.2 Video Setting★ ........................................................................................ 93
5.3 Screen Calibration .................................................................................... 94
5.4 Bell Setting............................................................................................... 95
5.5 The Definitions of Keyboards.................................................................... 97
6 Inquiry Record............................................................................................. 103
6.1 View attlogs............................................................................................ 103
6.2 View Time &Attendance Photo★............................................................ 106
6.3 View the blacklisted photos★ ................................................................. 108
7 USB Flash Disk Management .......................................................................111
7.1 Upload User data .................................................................................... 112
7.2 Download User’s Data ............................................................................ 112
7.3 Upload the Customized Picture ............................................................... 112
7.4 Download Attendance Datum.................................................................. 114
7.5 Users Upload Photos............................................................................... 114
7.6 Download User’s Photos★ ..................................................................... 115
7.7 Upload Short Message ............................................................................ 115
7.8 Download Short Message........................................................................ 115
7.9 Upload Flash .......................................................................................... 116
7.10 attendance photo download ★............................................................... 116
8 Information Release ......................................................................................118
8.1 Establish Short Message.......................................................................... 119
8.2 View Staff Short Message ....................................................................... 122
9. Systems Information ................................................................................... 124
9.1 Equipment Information ........................................................................... 124
9.2 Logs Capacity......................................................................................... 124
TFT Fingerprint V6.3
Appendix 1 Getting Familiar with Keyboard ................................................. 126
Appendix 2 T9 Input Method ......................................................................... 128
Appendix 3 Quickly Inquire Staff Attendance Logs ....................................... 131
Appendix 4 The Rule about the Advertising Pictures..................................... 133
Appendix 5 take photo while staff punch-in/out★ ......................................... 135
Appendix 6 battery specifications and Notice★ ............................................. 138
Appendix 7 About Anti-pass back function★................................................. 141
Appendix 8 Multi-combination Authentication Mode★ ................................ 146
Appendix 9 Remote server Solution★............................................................ 153
Appendix 10 WIFI★....................................................................................... 155
Appendix 11 GPRS★...................................................................................... 157
Appendix 12 Print function★......................................................................... 158
Appendix 13 Web Server ★ ........................................................................... 160
TFT Fingerprint V6.3
1 Main Windows
While device in readiness mode, Press
window, shown as following figure.
key to open main
Instruction
On the Main menu interface you will find eight icons menu,
namely: User Management, System Settings, Communications
Settings, Customize Settings, Record Inquiries, U flash disk
Management, Broadcast Information, Systems Information. In
some menus, there are some submenus.
1) No Submenu Status
A: Press Function Key to enter the corresponding interface (F1 ~
1
TFT Fingerprint V6.3
F8).
B: Press /
to move on, and press OK key to enter interface
for operation.
2) Submenu Status
scroll ▲ / ▼ key or press F1 ~ F8 submenu , the selected option
will become in black grey colour, press OK key to enter interface
for operation.
Press "ESC" key to exit from the menu.
2
TFT Fingerprint V6.3
2 User Management
For a fingerprint machine, user's basic information includes
fingerprint, password and management privilege. When the
company track staff Time & Attendance log, as a result of
reassigning staff, the user information in the fingerprint machine
also needs to correspondingly make the modification, therefore the
fingerprint machine provide function to add, delete, search, change
user and so on the operation.
2.1 Add new user
Firstly register the personnel’s fingerprint or the password on the
machine, whose time & attendance record will be tracked.
Enter the interface to add new user:
3
TFT Fingerprint V6.3
ID.NO: Staff' attendance number.
Name: use T 9 input method to key in user’s name.
Fingerprint: Registered staff's fingerprint, to register ten fingerprints is
available
the fingerprint may be used to check attendance by the staff whose
fingerprint has been registered.
Registration password: The registration user's password, the effective
figure of password is 1 ~ 8.
The registered password staff is possible to use the password to check
attendance.
Enroll card: registered users passwords.
Enroll Photos: register user’s Photos.
4
TFT Fingerprint V6.3
Registered user’s photographs will be displayed in attendance
performance.
Privilege: Users are people whose identity must be authenticated before
enter a menu. The ordinary consumer can track attendance by the
fingerprint or the password only; the manager already may equally carry
on the daily checking attendance with the ordinary consumer, but may
enter the menu to operate each option.
Note: When there is no appointed the manager, any person all may enter
the menu operation; after appointed the manager, be unable to enter the
menu until the manager status is confirm, after the success can enter the
menu.
Example: the flow to add user as follows:
Input ID.NO
1) The equipment is assigned ID.NO by default.
2) Press the " " key to delete the default assigned ID.NO, when
entry ID.NO with the keyboard, if occur error. May press " " to
delete it and input ID.NO again. Directly press "OK" key or scroll
the▲/▼ key, and locate cursor on the "Enroll fingerprint" button to
press the OK key again, go on the fingerprint registration.
Enter the name
Press the * key to open T9 input method, entry the staff ‘s name, with
T9 input method input by the ESC from the completion of T9 input
method. Directly press the "OK" button or scroll▲ / ▼ cursor keys will
be located in the "Registration fingerprint" button, then "OK" button,
enter the fingerprint registration.
5
TFT Fingerprint V6.3
Enroll fingerprint
Note: 1) the fingers is shown as yellow frame that present the
current selected finger.
2) The finger is shown as green that the finger has been registered,
if the finger has been registered, the fingerprints will be
re-registered and covered with the previous fingerprints.
3) Select the registered fingers, press keys to delete the fingerprint
that is available.
4) Figure fingerprints registered in the default order of
2,3,4,5,0,9,8,7,6,1.
press key with the digital keyboard or scroll ▲/▼/ / button, or
touch the fingers which will be registered fingers. Follow the
equipment prompt place the finger, you must continuously press
the same finger 3 times in the correct method until the registration
successful prompt appear
6
TFT Fingerprint V6.3
After registering fingerprint successfully, if need to continually
register another fingerprints to press finger, directly after the
completion of registration by (F7), "ESC" (F8) to return to the
previous interface, The equipment will prompt the current number
of registered fingerprint.
Scroll▲ / ▼key, the cursor will be located in the "Registration
password" button, and Press "OK" to enter password registration.
Register Password
Following the equipment prompt, input the password , then press
OK key and input password once again , only it is allowed to input
1 ~ 8 the effective figure for the password . After the input to save
completed press
(F7), if does not save it, press "ESC"(F8).
After saving it, the icon
will display on the screen, which
mean the password has already set in the device.
7
TFT Fingerprint V6.3
Enroll cards ★
Scroll ▲ / ▼keys to locate the cursor on “enroll card" button, and
press "OK" to enter the registration card.
Slight ware the card near the induction area, after the equipment
found the card number, then remove the card from the equipment,
after equipment prompt that the "Enroll successfully" the card
number will be save up, or may press “Done” button to return to
register interface.
After enrolling the card, the
icon will display equipment
screen that means the cards is registered card, the employees can
punch card to track whose attendance.
Take photo while track staff Time & Attendance mode ★
Scroll ▲ / ▼ key to locate cursor in this option, Scroll /
8
key to
TFT Fingerprint V6.3
set photo mode.
There are total of four kinds of mode, here configure setting for the
current staff, when staff punch-in/out his /her photo will be taken
by Time clocker model
(1) The global settings: that the staff follows the taking photo mode
in the interface settings to set the taking photo as punching in/out.
(2) Do not take photographs: that came does not take staff’s photo
after the punch complete.
(3) Take photographs: that after the staff signed attendance record,
take photo but does not save it.
(4) Take photographs and save: after the staff punching–in/out
the camera take photo and save it .
Registration photos ★
scroll ▲ / ▼keys, the cursor will be located in the "Registration
Photos" button, and press "OK" to enter the video interface, to
configure photo capture function is available .
9
TFT Fingerprint V6.3
After entering a snapshot mode of the equipment interface, scroll
▲ / ▼ key to switch options input box with the small keyboard,
and input appropriate number keys to adjust the value of the
(F7)
camera filming effect, after appropriate adjustment press
or "OK" that is, photos can be captured, after the completion of the
snapshot capture and save pictures, and the photograph swill
showed for two seconds, re-entering the snapshot mode. If you
don’t satisfied with the pictures taken, press the "return" button.
Continually capture photo again until you are satisfaction.
View
Scroll▲ / ▼keys the cursor will be located in the "Registration
Photos" button, and press "OK" here to view these registered
pictures.
10
TFT Fingerprint V6.3
Press any one button or touch the region of images on the screen,
can exit from photo browser.
Privilege setting
Scroll the▲/▼ key, and locate cursor on the "AUTH" option box,
Scroll / key to choose privilege.
Save/exit user registration
To confirm the registration information is correct, after getting
confirmation, save it.
The way for saving:
1) Press "
"(F7) the key ,the prompt “Save successfully!
Continues to input?" on the equipment, press "OK" the key to save
it, if you Do not want saving, Press “ESC”
11
TFT Fingerprint V6.3
2) press "ESC" to exit. If the prompt "the data has been changed,
Are you sure to save it?” appear on equipment, want continuing to
press "OK", if you abandon this operation, press "ESC" key to
return the previous menu.
2.2 View User
By means of the user view you can view all users' information in
the current equipment is available, which include username, the
number of fingerprint, whether the password is registered, and
user’s attendance logs. You are allowed to edit or delete some user
Note: 1) Shown as above figure, the icon
express that this staff
is a manager, the icon
express that the password has already
been registered.
12
TFT Fingerprint V6.3
2) The RF card No. will be displayed on the Card No. Rank
Scroll ▲/▼ key , the blue cursor locate at the line that want to
be operate, press the function key where around the screen both
side to do operation, Example , press F1 key to search user.
2.2.1 Search for users
When there are lot of registered user in the device, in order to
provide the manager with convenient rapidly to find a staff, the
equipment come with "ID.NO" “Name” to retrieve the staff.
Press the F1 key in the user browser interface, the operation menu
appear:
Input staff's ID.NO that you search for, press the "OK" key to
search, after searching successfully, the blue cursor will
13
TFT Fingerprint V6.3
automatically locate on this staff name, if this staff you search does
not exist in the device, the prompt "the non- registration data"
will appear.
2.2.2 Inquiry Attendance
When the manager examine staff's registration information and
fingerprint so on, meanwhile may track the staff’s attendance
record in the same month.
Press the F2 key in the user management interface, the operation
menu appears, choose "Attendance inquiry" item, may track the
staff’s that you choose the attendance record in the same month:
Scroll ▲/▼ key to browse the attendance log line by line.
Press F6/F7key to browse the attendance log page by page.
14
TFT Fingerprint V6.3
Press“ESC”/F8 return the user browser interface
Press OK/
/F5 key to inquire the detailed situation.
After the examination completed, press "ESC" (F8)key to return to
the user management interface.
2.2.3 Add New User
There is an option that is easily operator to add user in the here, the
function is some with 2.1 introduce. Press F3 to enter
2.2.4 Edit User
Makes the revision for user's information which have been saved in
the machine, for example, if the registered fingerprint is invalid ,
renew the fingerprint or register the password, just enter the "
15
TFT Fingerprint V6.3
edition user" available.
Press the "
" /OK /F4 key to display the user’s information
which has been registered:
The ID.NO is not allowed to revise again, other operations is
similar with to add the user. Register the fingerprint again, if there
is not the password or need to revise the password, then directly
click on "Chg Pwd", the privilege also is allowed to revise.
Save edition/Exit edition
1) Press "
" the key to save editing result and return to the user
management interface.
2) Press the "ESC" key , the prompt "the data have been changed,
are you sure to save it" display on the equipment press OK, press
“ ESC” key to abandon operation.
16
TFT Fingerprint V6.3
2.2.5 Deletions users
The option "deletion user" is to delete staff's partial information or
all information from the equipment, which apply to the following
situation:
1) The staff's fingerprint or the password is invalid or Do not use it
any more.
2) After the staff lay off, administrator deletes her/his record from
the equipment.
In the user management interface, scroll ▲/▼ key or search user to
locate the blue color cursor at the staff that needs to edit, press the F5
key. The operation menu appears, your choice is "deletion user".
Deletion user
17
TFT Fingerprint V6.3
If there is not user’s fingerprint or the password in the device, then
his /her corresponding typeface is a blue color, be unable to operate
it, scroll the ▲/▼ key to locate the cursor at the option which
need to operate. Press the "OK" key the dialog box which asks you
give confirmation will pop-up whether delete this item, after
confirmation, the equipment should create the corresponding
prompt, press "ESC" (F8) key to return to the user management
page.
2.2.6 User Access Control
★
There is a access control option in the user view interface of the
fingerprint machine with access control, a single-clock the
operation of menu, select "User Access Control.".
Instructions:
If the fingerprint machine provide with a Access Control function,
the access control option will appear on the User brows interface
18
TFT Fingerprint V6.3
Press F4 to enter user access control setting
User Access Control Setting is to set privilege to open the door for
each individual . These include: Group-owned setting, verification
methods, used Time Period, the verification methods, fingerprints
management. Group: registered users will be assigned to the group,
it is easily manageable;
Using Time Period
1) the group Time Period: the user whether or not use their default
the group Time Period.
2) Users Time Period: to set up the user unlock time. That is not to
use group time, the group does not affect the other people unlock
time.
Verification methods
1) Group verification types: the user whether use the group
verifying types or not.
19
TFT Fingerprint V6.3
2) Personal validation types: individual users choose the type of
verification, or non-use type verification group, the group does not
affect other types of verification.
Duress fingerprint management
a newly registered users or specialized appoint a fingerprint which
has been registered in the fingerprint machine to the Duress
fingerprints. In any case, the fingerprint match successfully, then
produce the duress alarm.
Note: equipment provides a wideϑ range of types verify, specific
See Appendix 8, Multi- verification.
Some equipment do not provide with this function
Instructions:
Scroll ▲ / ▼ key to move the cursor to the optional items. If the
item is the input box, input the value with the small number of key
20
TFT Fingerprint V6.3
keyboard, If it is a rolling box, Scroll / / key to switch the
provided value, when the cursor locate at "manage Duress
fingerprint" button, Press Ok key to enter the Duress fingerprints
management. After completing setting, directly press F7 key to
save it and return to the previous interface, press the "ESC"/F8 to
Cancel and return to the previous setting interface .
Instructions
1) Definition / cancellation Duress fingerprints
on the above interface, Press the OK/F2 key to define / cancel the
current Duress fingerprints you selected.
Press F3 to cancel all selected fingerprint, Do not serve as the
duress fingerprints.
2) Duress fingerprint registration
In the above interface, press the F4 to enter enrolling interface,
21
TFT Fingerprint V6.3
after registering the successfully in the register interface you will
find that the fingerprints are designated as Duress fingerprints.
3) Save the duress fingerprints
If confirmed definition of duress fingerprint in the above interface ,
press F 7 to save the setting , press F8 to give up.
2.3 card management
★
Support contact less smart Mifare cards with the working
frequency 13.56 MHZ, which the fingerprint time and attendance
can be integrated into other systems, multiple authentication
methods is available to meet the needs of different groups of
people.
Note: card management options only with some special models.
Instructions:
22
TFT Fingerprint V6.3
Scroll ▲ / ▼ key to select, press "OK" button perform the selected
item.
2.3.1 Enroll ID Card
If Mifare card is intended to use as ID cards, just the registration
card number enough, do not need to register their fingerprints.
Instructions:
1, registration
Step 1: Select button registration number card, press "OK" button.
23
TFT Fingerprint V6.3
Step 2: type the registration number by the keyboard (if the number
is already existing in the user equipment, the equipment will
prompt whether the information will be copied to the card), then
press the "OK" button.
24
TFT Fingerprint V6.3
Step 3: place the card near the induction area like tradition swipe
card, until the equipment tips registration / copy is successful.
2, the certification:
Wave the card in the induction area, after the card is found by the
equipment, then remove the card, equipment will prompt that the
verification is successful and complete verification.
Note: Please enter the User Access Control settings to change the
verification method to RF, otherwise it will fail to verify.
2.3.2 Enroll FP Card
Register their fingerprints and write fingerprints into the card.
25
TFT Fingerprint V6.3
Instruction
1, registration
Step 1: Select the button to register their fingerprints cards, press
"OK" button.
Step 2: Type the registration number by the keyboard (if the
number is already existing in the user equipment, the equipment
will prompt whether the information will be copied to the card, go
to Step 4), then press the OK button to enter the fingerprint
registration interface.
26
TFT Fingerprint V6.3
Step 3: properly press the finger for three times.
Step 4: equipment will prompt to punch the cards
27
TFT Fingerprint V6.3
Step 5: place the card near induction area, waiting for the
equipment will read fingerprint data into the card, until the success
of the registration equipment tips appear.
2, the certification:
Place the card near the sensors area and wave it, after the
equipment find the card, remove it from the sensor, equipment tips
to press fingerprint, after the successful completion of verification.
If the placed fingerprint is inconsistent with one that is stored in
cards, than failed to verified.
2.3.3 Erase card information
The current information in the used card will be deleted all.
Instruction
28
TFT Fingerprint V6.3
place the card under the induction space, waiting for the equipment
remove the card information, if the card data has been stored in the
devices, the equipment will also asks if you want to delete the
information from the equipment, choose "Yes" to remove within
the user Fingerprints and information from the equipment, choose
"No" to retain information on the device.
2.3.4 Copy card information
Card information will be copied to the device (after copied, the
fingerprint still exist in card), finish coping. It is able to directly
punch-in/out by fingerprint on the device, without the use of Mifare
cards.
Instruction
29
TFT Fingerprint V6.3
scroll▲ / ▼ button to select only copy user information, or copy
user information and fingerprint, then "OK" button
30
TFT Fingerprint V6.3
2.3.5 Card setting
Setup a password of Mifare card and whether save the information
to the machine.
Fingerprint Card Password: after set the password, the device will
write the password into fingerprint card that has been registered on
the machine, this fingerprint card can only be used on this machine.
Information must save to this machine: While is registering card
No or fingerprint card, whether or not saved to the registered
information to the machine. If selected as "No", only the
information will be stored on the card; selected as a "yes", then the
card and the equipment all have the data.
Instruction
31
TFT Fingerprint V6.3
Scroll ▲ / ▼ button to move the cursor to the setting item. If it is
the input box, press the number keys of keyboard to input to the set
value ,if the rolling box, scroll / key to switch to set the value ,
directly press the "OK" button or F7 to save the settings and return
to the saving interface , press The "ESC" F8 or cancel your settings
and return on an interface.
Note: card induction space locate in the fingerprint sensor above 3
cm-5cm area.
2.4 work codes★
Time & Attendance record is basis to compute payroll, the staff
possibly assign to the different working category, also possibly has
dissimilar kind of work in one factory in the different time, the
different work category has dissimilar the reward, therefore, the
equipment provide user with parameter to indicate tracked record
that belongs to kind of working category in a factory, provide
convenience and very easy to process time & attendance
data ,could fast distinguish the different punching
in/out
situation .
Note only some specify model of machine provide this function
Instruction
32
TFT Fingerprint V6.3
Scroll the ▲/▼key to view work code line by line .
Scroll the F5/F6 key to view work code s page by page.
Press F1 add a new working code
Press the "OK" key to edit view work code of your choice.
Press the
key, the menu to set work code will appear.
2.4.1 Set work code
1) Add the work code
Press F1 to add a work code.
Code: A number word code of this work code.
Name: express the mean of this work code
Instruction
33
TFT Fingerprint V6.3
scroll the ▲/▼ key to switch input box , type into figure by
numerical key, start T9 input method to enter name, after complete
setting press the "OK" button or F7 to save the settings and return
to the save interface , press The "ESC" F8 or cancel your settings
and return previous interface
2) Edit the work code.
Press OK or F2 to change the selected work code
3) Delete the work code
Press F3 to delete the selected work code
2.4.2 Using work code
When the equipment is in the standby interface, press shortcut t (set
it in keyboard definition) enter the work code input interface.
34
TFT Fingerprint V6.3
The user may directly input work code, press OK key to confirm.
The name of work code will appear on state bar( for 5 second), then
press OK key to return main interface.
2.5 Access Control setting
★
Access Control settings are designed for user’s Time Period and
control unlocks and related parameters of equipment settings.
if Registered users are unable to unlock until he/she comply with
the following conditions:
1, the current unlock time should be within any effective Time
Scope of the User Time period or the user group Time Period;
2, where the user must be in unlock group combine ( user also can
35
TFT Fingerprint V6.3
work with other group unlock combine, but it is unable to unlock
until user work with together).
New register user belong to the first users group by system default,
the default the group Time Period is "1", the default unlock
combine is the first group, and newly registered users is defaulted
as the unlock state (if the user has modify the related setting of the
Access Control, the system will change along with users).
Instructions:
Scroll ▲ / ▼ key to select, press OK button to perform selected
item.
2.5.1 Time Period Setting
Time Period is a minimum Time Period unit of Access Control
36
TFT Fingerprint V6.3
option. The whole system can be defined with maximum 50 Time
Period. Each Time Period is the defined as seven hours a week,
each Time Period is the effective time in 24 hours a day. Each user
can own maximum3 Time Period, the three Time Periods are "or"
relationship, as long as the Time Period the certification to meet
one of these three Time Periods is effective. The time of each Time
Period format: HH: MM-HH: MM, in accordance with the 24-hour
system that is accurate to the minute.
The end of time is less than starting time (23:57 - 23:56) that
represent the day is prohibited, ending time is larger than starting
time (00:00 - 23:59) that take effective in this range.
Users unlock the effective time of: opening day (00:00-23:59), or
time, the ending time than the beginning of time.
Note: the system's default Time Period is the No. 1 for opening all
day (that is, newly registered users is permitted to unlock).
Instructions
37
TFT Fingerprint V6.3
Be able to view all the Time Period of the current setting from the
list.
Scroll ▲ / ▼ keys to view of the Time Period line byline.
Press F6/F7 to view Time Period page by page.
Scroll / keys to browse the complete information of The Time
Period of the current selection.
1)
Add Time Period
Press F2 on the new time period:
38
TFT Fingerprint V6.3
The system will automatically assign a serial number of Time
Period in accordance with the priorities, scroll ▲ / ▼,
/ button to move the cursor to the input box, press the key to
input figures of the Time Period, after the completion of setting ,
press the
/ F7 save the settings, press F8 / "ESC" Exit.
2) Edit Time Period
Press F3 to edit the selected Time Period.
3) Delete Time Period
Press F4 to delete selected the current Time Period. 4) Exit the
Time Period setting
press F8 / "ESC" exit from the Time Period setting.
39
TFT Fingerprint V6.3
2.5.2 Holidays setting
Introduce the concept of holidays to Access Control. Whenever the
holidays is taken, we may need a special Access Control hour, but
it is very tedious to change everyone's Access Control hours, so
can set up a holiday Access control hour, and this Access control
hours is applicable to all staff.
Instructions
It is allowed to view all the holidays of the current setting from the list.
Scroll ▲ / ▼ keys to view of the holidays line byline. Press F6/F7 to
view the holiday page by page.
1) Add Holiday
Press F2 add the new Holiday:
40
TFT Fingerprint V6.3
The system will automatically assign a serial number of holiday
in accordance with the priorities serial number, scroll ▲ / ▼,
/ button to move the cursor to the input box, press the keyboard
to input figures of the holiday, after the completion of setting, press
the
/ F7 save the settings, press F8 / "ESC" Exit.
2) Edit holiday
Press F3 to edit the selected Holiday.
3) Delete Holiday
Press F4 to delete the selected current holiday.
Note: If the Access Control holiday hours has been set, the user in
the holidays of a few days open the door that depend on the time
set here
41
TFT Fingerprint V6.3
2.5.3 Group
setting
Group function is divided user into groups, personnel management,
the group using the default group staff Time Period, the group is
allowed to set the user Time Period. Each group have three Time
Periods. Newly registered users belong to one group by default, but
who can be re-assigned to other various groups.
Instructions
It is allowed to view all the Access Control Group of the current
setting from the list.
Scroll ▲ / ▼ keys to view of the Access Control Group line by
line.
Press F6/F7 to view Access Control Group page by page.
1) Add Access Control
Press F2 to enter the new interface, such as adding a Group that
include Time Period 2 and Time Period 3:
42
TFT Fingerprint V6.3
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If it is the
input box, input to provide value with the small number keyboard,If it
is a rolling box, scroll / key to switch and set its value, after
complete setting, directly press the menu keys to save setting and
return the previous interface, press the "ESC " button to cancel and
return to the previous interface.
Note: During holiday, the open-door time zone of this group keeps to
the following rules:
1. When the holidays is set as effective, the member in the group
can open the door in both access control time zone and holiday
time zone.
2. When the holidays is set as ineffective, the group member can
open the door in the access control time zone except for holiday
time zone.
43
TFT Fingerprint V6.3
2) Edit Access Control Group
Press F3 to edit the selected Access Control Group.
3) Delete Access Control Group.
Press F4 to delete selected the current Access Control Group .
2.5.4 Unlock combination setting
Each group will be combined into different unlock combination, so
that we can achieve multiple authentication functions and
improving the Access Control security. one in the largest unlock
combination that can have five groups formed.
Instructions
It is allowed to view all the unlock combination Access Control
Group of the current setting from the list.
44
TFT Fingerprint V6.3
Scroll ▲ / ▼ keys to view of the unlock combination Access
Control Group line byline.
Press F6/F7 to view unlock combination Access Control Group
page by page
above The figure there are
three unlock combination in
equipment, the first, the staff of the Group 1 can pass verification to
unlock, and the other is the staff of Group 2 pass verification to
unlock; Third Group 3 and Group 4 of the people together through
the verification Be able to unlock.
4)
new unlock combination
Press a menu button, the operation menu appears.
Press F 2 to enter newly add interface such as add a the
combination that can unlock in event of which group 2, group 3
together verify successful, as shown below:
45
TFT Fingerprint V6.3
Scroll ▲ / ▼ key to move the cursor to the input box, input the
value to be set through the small number keyboard, after the
completion, press the menu keys to save settings, Press the ESC
key to exit
2) Edit unlock combination of Access Control Group
Press F3 to edit the selected Access Control Group.
3) Delete unlocks combination Access Control Group.
Press F4 to delete selected the current Access Control Group.
46
TFT Fingerprint V6.3
2.5.5 Access Control Parameters
Configure Lock control and related equipment parameters.
Duration of locks driving: The equipment control performance to
unlock after how long time. (RMS 1 ~ 10 seconds)
door sensor delay: the door sensor delay is the duration after the
door was opened, How long time to check door sensor after a
period of time before detection to open the door, if door sensor
state and door sensor switch inconsistent normal began alarm,
during this period of time is door sensor delay. (RMS 1 ~ 5
seconds)
door sensor : There are three type: No, normally open, and NC
normal closed; None referring to the non-use of door sensor , and
normally open the doors opened that is normal, and normally
close that door closed is normal state.
Door sensor alarm delay: Do not detect door sensor state at
normal state , if over this hours to produce alarm signals, the hour
is door sensor alarm delay. (RMS 0 ~ 99 seconds)
Alarm Times by mistake: When the number of identification fail
to pass arrived at the number of the wrong values, they have a
warning signal. (RMS 0 ~ 9th)
Normal close Time Period : Access Control often set the door to
closed during the Period of Time, or any person in this period of
time is not able to unlock.
47
TFT Fingerprint V6.3
Normally open : set up a regular hours in Access Control system,
the lock in this period of time is in the opening state .
The validity of holidays: definition normally open or normally
closed at the time of the holidays, set a specific period of time take
effect.
Note: 1, if the Time Period of normally open or normally closed has
been set, please switch door sensor to no, otherwise it
will produce alarm signal during Normal close Time
Period or Normal open Time Period .
2, If the normally open or normally closed
Time Period is not defined yet the time, the equipment
will prompt that you define the Time Period, and
transferred to the Time Period interface , to adding.
Instructions:
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If it
48
TFT Fingerprint V6.3
is the input box, input to provide value with the small number
keyboard,If it is a rolling box, scroll / key to switch and set
its value, after complete setting, directly press the menu keys to
save setting and return the previous interface, press the "ESC "
button to Cancel and return to the previous interface.
2.5.6 Duress alarm parameters
Machines also has Duress alarm parameter setting, use newly enroll
specialties fingerprint or define an enrolled fingerprint as the duress
fingerprint , the system will trigger an alarm signal when this
fingerprint has been authenticate through fair and foul.
Seeking help by Keys: If this item set as "Yes", hold down Help
keys ( for three seconds and above), produce the recourse signal;
press the Help keys followed (3 seconds) or input ID or place
fingerprint, after the success of identification at the same time a
Duress alarm will be triggered , if the keys for help is set to "no",
then press and hold down "▼" button, take no role.
1:1 verification methods alarm: If this item is set to "Yes", after
users performance 1:1 verification successfully, will produce alarm
signals. Otherwise there will be no warning signal.
1: N verification methods alarm: If this item is set to, "Yes", after
users performance 1: N verification successfully, will produce
alarm signals. Otherwise there will be no warning signal.
Password alarm: If item is set to, "Yes", after user go on password
verification successfully, will trigger alarm signals, otherwise it
will not produce alarm signal.
Alarm duration: after trigger the Duress alarm, Do not directly
49
TFT Fingerprint V6.3
output signal, but after a period of time that can be defined, then
automatically alarm signal (0-255 seconds).
Instructions:
Scroll ▲ / ▼ key to move the cursor to the items to be set up. If
the input box by the small number of key keyboard input to provide
value If it is a rolling box, press / key switch to set its value,
directly installed by the end of the menu keys can be set up and
returned to the preservation of the previous interface, Press the
"ESC "Cancel to return to the previous set and interface
2.5.7 Anti-pass
back Setting★
Configure Anti-pass back function of this device, for more detail;
50
TFT Fingerprint V6.3
please refer to appendix 7 about anti-pass back function.
2.5.8 Relieve alarm
Equipment is in a state of alarm, press the
menu button, the
device will be called "whether to relieve alarm?", alarm has been
thrill until If you relieve alarm state. After choice is to relieve
alarm, the equipment will return to normally state.
The type of alarm equipment: there are door sensor alarm, which
detection door was opened without authorization, anti-dismantle
alarm. Duress alarm
51
TFT Fingerprint V6.3
3 System Setting
To set up system parameter, make the equipment at the function,
display with the perfect exhibition, pursue user's satisfactions.
3.1 Systems parameters
1: 1 matching threshold: When use ID+ fingerprint to recognize.
Threshold a predefined number , often controlled by a biometric
system administrator , which establishes the degree of correlation
necessary for a comparison to be deemed a match .if the score
resulting from template comparison exceed the threshold , the
templates are a “match” ( though the template them selves are not
identical
1: N matching threshold: the degree of correlation matches with
the registration template.
52
TFT Fingerprint V6.3
Recommend matching threshold setting: e. (effect value is 1 ~ 60
minutes)
Suggested Threshold Settings
FRR
FAR
One-to-many
One-to-one
High
Low
45
25
Middle
Middle
35
15
Low
High
25
10
Time format: Set up the time format in the fingerprint initial
interface.
Scroll /
key to choose form, the fingerprint machine supports
10 kinds of dates forms, YY-MM-DD, YY/MM/DD, YY.MM.DD,
MM-DD-YY,
MM/DD/YY,
MM.DD.YY,
DD-MM-YY,
DD/MM/YY, DD.MM.YY, YYYYMMDD, and other date form of
your choice
Keyboard voice: Scroll the / key to determine the whether
send a sound when you press key , if set the option as
"Yes" ,when press key the machine will utter, if set the option as
("No") you press key the machine doesn’t utter.
Voice (Adjvo): Through the / / key configure the voice prompt,
the equipment can produces the corresponding voice Prompt when
the operation.
Volume: Adjust volume. Scroll
53
/ key to adjust volume as your
TFT Fingerprint V6.3
favor
Alarm attendance log( Alm Attlog), When the remainder log
capacity reached set numerical value, it will automatically sound
warning that logs will be full ( virtual value is 1-99).
Recheck Minute: set it within the scope (unit: minute). Someone
attendance has been recorded, then the second record will not
display (virtual value is 66).
Fingerprint sensitivity: adjust the fingerprint sensors, the
fingerprint sensor are too sensitivity, lower the value; When the
first fingerprint sensors is too slow, increase the value of. (Scope 1
~ 10 )
Photo Space warning: When the remaining space of the
equipment memory card reach the set value, the equipment will
automatically warn for lack of space, please delete the expired
photos in time, otherwise the equipment will not be able to store
attendance photos.
Instruction
54
TFT Fingerprint V6.3
Scroll the▲/▼key to shifts the cursor on the item which you need
set. If the item is inputting box, configure the value with the
numeric keyboard input; If the item is rolls the frame, Scroll
the / key to choose the value you need, after the setting finished,
please directly press OK or
(F7) key to save this item and
return to preceding interface, press the ESC (F8) key to give up
operation and return to interface.
55
TFT Fingerprint V6.3
3.2 Time and Date settings
3.2.1 Time and Date setting
It is necessary to set the accurate date and time for each of
equipments. To obtain guarantee for tracking the accurate
attendance result.
Enter option to set the time and date :
Instruction
Scroll the / key to switch option input box, Scroll▲/▼key to
shifts the cursor input box . set up the value with the numeric
keyboard input After you set up completed, please press
/“OK”
(F7) to save this configuration, press the ESC(F8) key to
56
TFT Fingerprint V6.3
abandon operation and return to the up page
3.2.2 Daylight
Saving Time
Daylight Saving Time, also known as "daylight saving time
system” is a man-made the local time for saving energy , during the
system is used this unity time known as "daylight saving time."
Usually in the early morning of the summer people will be one
hour ahead of time, people can get up early and early sleep to save
lighting to make full use of resources illumination, save electricity.
at autumn fall Then call back one hour. The different countries
have different specific requirements of daylight saving time.
In order to meet the needs of daylight saving time, we can offer a
special custom features, in XX, XX, XX, XX hours, fast one hour,
and by the XX, XX, XX-XX, then slow one hour .
Note: Daylight Saving Time function only provide by certain
models.
Instruction
When the device have this functional, in the time period interface
there will be set up options:
57
TFT Fingerprint V6.3
1) Set Daylight Saving Time option as "NO."
2) Assign Daylight Saving Time start and end times.
For example, setup at 8:00 on April 1, the machines come in the
Daylight Saving Time, the counting time will be ahead for one hour.
To at 8:00 on October 1, equipment returned to normal time.
58
TFT Fingerprint V6.3
3) press
/ "OK" (F7)to save the settings; press the "ESC" (F8) does not
save and exit
3.3 Data managements
Delete attendance record (Clear Attlog): Deletes all attendance
record.
Delete the complete datum (Clear All): Delete all registrations
personnel information, the fingerprint and the attendance record.
Clear Admin Privilege: Change the Administer privilege into
ordinary users’ option:
Delete Attendance photos: Delete all photos to track all staff the
time and attendance record.
59
TFT Fingerprint V6.3
Delete blacklist photos: delete the photos which are captured and
saved when user fail to punch in/out.
Caution: Unable to restore any file you delete, please careful
Instruction
Scroll the▲/▼ key to shift the cursor on the button which you
will operate. press OK to start operation, when the prompt “ Are
you sure to continue the current this operation?” appear on the
equipment, press OK key again , be sure that the data will be
deleted, if after you delete the data, the data will be unable to
restore. Press ESC (F8) key to exit and return to up aged.
Remove publicity Photo: remove publicity pictures when
equipment cycle show in ready working interface. (How to upload
pictures, please See 7.4 upload custom publicity Photo)
60
TFT Fingerprint V6.3
Instruction
Scroll the “F3/F4” key to preview the publicity picture which has
already saved in the equipment, if you want to delete this picture
then press F6 key to delete it, after the prompt to delete
successfully appear on the equipment , after deleted completed
automatically jumps to the next picture. If you want to delete all
public picture in the equipment, Press
(F7)button. Press the
ESC (F8) key to return to the data management interface.
3.4 Upgrade firmware
If want to upgrade the firmware of machine, may use USB flash
disk to achieve.
Caution: to protect your normal use, we need to restriction that
61
TFT Fingerprint V6.3
forbid anyone upgrade the firmware random, except with the help
of the dealer upgrading the firmware. Inaccuracy upgrade would
trouble the machine, that possibly affect the daily use.
Instruction
Plug the USB flash disk with Upgrade file into slot of equipment,
click this item, the equipment will automatically recognize
upgrading file and upgrade firmware, the corresponding prompt
will appear to show upgrade successfully or fail.
3.5 Restore Setting
Restore the communications setting, system settings, to the factory
settings.
Reset all the default Parameters: the parameters of the machine
will be fully restored to factory settings.
Reset the keyboard Parameters: the keyboard corresponding
definition set to the factory settings.
Reset Alarm Parameters: the alarm settings call back to the
factory settings.
Reset Other Parameters: communications settings, system
parameters, such as the interface settings call back to the factory
settings.
Reset Access Parameters: access control settings and user access
control settings back to the factory settings
Instruction
62
TFT Fingerprint V6.3
Scroll ▲ / ▼ key to select, press OK button to restore the settings.
Note: to restores the setting cannot erase the personnel information
and the attendance record in the equipment.
3.6 Automatically test
The equipment provides with the automatic test function to test
each module in the fingerprint machine. The function helps the
operator firstly check the module, if the machine has some problem.
Include TFT screen, voice prompt, clock, keyboard, and fingerprint
sensor test. Choose the option to test.
63
TFT Fingerprint V6.3
Scroll the ▲/▼ key to select the item that needs to be tested,
press the "OK" key to start the testing
3.6.1 Test TFT screen
Equipment provides auto-test to check the TFT screen
demonstration effect. Through when the screen displays in color,
entire white, entire black, you can inspect each place of the screen
at this time, to check whether the TFT screen demonstrates
normally.
Press “OK” to continue to test whiles the test process, press ESC
key to exit from this test.
64
TFT Fingerprint V6.3
3.6.2 Test pronunciations
The equipment offer auto-test effect of the voice prompt, through
playing voice file in the equipment, to check whether the voice file
is completed and the pronunciation effect is in good or not
Press
/“OK”(F7) to continue playing voice while the test
process, press “ESC”(F8) key to exit from this test.
3.6.3 Test keyboards
The equipment carries on the automatic detection to each keyboard,
to test whether each key of keyboard is normally used. In the
keyboard test window, stochastically press any key of the keyboard
(except the "OK" and "ESC" F8 key), check whether the key you
press accords with the display on the screen. The key you press
display in garnet
color, otherwise the key
in gray black.
Press “OK”、“ESC”(F8) key to exit from this test
3.6.4 Test fingerprint Sensor
The auto-test fingerprint sensor tells user whether the sensor is in
normal, through the test you can examine the picture resolution of
the fingerprint, to whether the fingerprint picture is clear, and the
screen will real-time show fingerprint picture that is captured from
the finger while you are placing the fingerprint sensor window.
Press “OK”、“ESC”(F8) key to exit from this test.
65
TFT Fingerprint V6.3
3.6.5 Real-time clocks
The equipment provides function to test the clock, through
stopwatch test you will get result that whether the clock is in
normal operation or not.
Press the
/“OK” key to start to time, press the
/“OK”
key again to stop it, to check whether the equipment time is in
accuracy. Press “OK”、“ESC”(F8) key to exit from this test.
66
TFT Fingerprint V6.3
4 Communication setting
Set data transmission mode, when font colour appear on the button
by blue colour, that indicate the equipment is unable to support this
function
4.1 Communication setting
Scroll“▲/▼”key to set communication setting, press OK to enter
setting.
If when the data is transferred between the equipment and PC, it is
necessary to set the equipment communication parameter according
67
TFT Fingerprint V6.3
to the transmission cable. When the equipment and the machine are
in the communication, the "in the work... ...” Message will be
displayed on the equipment, Please Do not operate the equipment
while the test is running.
Note: please inspect the setting here before the machines communicate
with the computer, the parameter must be consistent with the one on the
communication option in the software.
To find sitting on the fingerprint machine if you are using Ethernet
communication, following sitting:
Machine IP address: Default IP is 192.168.1.201, you must
change it; Do not set IP as same as the IP of PC that the fingerprint
machine connect with.
Subnet mask: Default mask 255.255.255.0, you must change it.
Gateway address: the Default gateway address is 0.0.0.0, if the
equipment and PC is not in the identical network segment, set up
the gateway address firstly.
Network speed: The network run speed, there are three kinds of
options, automatic adoption, 10M, the 100M. Set network speed
according to your equipment that is plugged into a locate area
network using Ethernet cable.
To find sitting on the fingerprint machine if you are using serial
port (RS232/RS485) to communicate between the equipment and
PC, configure the following parameter:
Baud rate: the rate at which fingerprint machine communicate
with the PC , there are five kinds of options 9600, 19,200, 38,400,
68
TFT Fingerprint V6.3
57,600, 1.15200 bit/sec, the high speed communication is quick,
we recommend that high speed apply to the RS232communication ;
The low speed communication is stable, it is better the low speed
apply to theRS485 communication;
RS232: Whether using RS232 communication or not, if the RS232
will be used, then this choice is "Yes";
RS485: Whether using RS485 communication or not, if the RS485
will be used, then this choice is "Yes”
It is necessary to set the serial number before the PC communicates
with the fingerprint machine over the RS232/RS485 cable.
Serial number: The serial number of the fingerprint machine,
which scope is from 1 to 254, if when using the RS232/RS485
communication, be sure to input this serial number in the software
communication interface firstly.
In order to keep up the security of the time & attendance record
data, here you may set up the connection password, unless input
this connection password in the PC machine software, and
fingerprint machine is unable to interconnect to read the data when
the fingerprint machine connect to PC successfully.
Connection password: The system default password is 0(namely
the password does not exist), it is allowed to set it as other values,
after setting up, be sure to input this password before the software
communicate with the equipment , otherwise you will fail to create
connection between the fingerprint machine and PC software. The
connection password length is 1 ~ 6.
69
TFT Fingerprint V6.3
Instruction
Scroll the ▲/▼、 / key to shift the cursor on the item you need
set, scroll the / key again to shift the value which you choose.
After setting up, directly press
/“OK”
(F7)key to save this
setting and return to preceding interface, press the “ESC”
(F8) key
to cancel and return to preceding interface.
4.2 Remote verification
★
Taking standalone machine as fingerprint scanner, its standalone
identification function is reserves. With identification and
verification, and then stores matching results in the background DB
and displays identification results on the fingerprint machine LCD,
to complete the task of identification process. Which Identification
70
TFT Fingerprint V6.3
algorithm adopts intellectual property algorithm Biokey , the
common PCs can act as remote server, the remote sever solution
has lower requirement of entire identification system and improve
algorithm efficiency, thus assure of feasibility and convenience of
solution.
Solution Purpose: large capacity of fingerprint identification,
enhanced enterprise internal management, intelligent management,
In/Out control for personnel.
Which apply to solve factories and other large databases for slow
tracking the attendance problem, and offer the domain and similar
DNS solution to resolve persons change in the factory? These
server locations are plotted by the logic, dynamic identify the flow
person, do not need to manually modify the flows person, the
movement to achieve arbitrary. And flexibility in the use of similar
DNS provided by DNS function, the system is more stable, the
allocation of resources is proper, to improve efficiency in the state
of emergency, system can operate normally.
Instruction
71
TFT Fingerprint V6.3
Scroll "▲ / ▼" button to select background verification, press the
"OK" button to enter settings.
Server IP: fingerprint authentication server set up the IP address
(that is, a PC's IP address, with authentication server software)
Remote Authentication: there are four ways available to choose:
"NO", "NL", "LO", "LN".
LO (only local), that is, only perform verification on the
fingerprint machine (default);
NL (net local), background has verified that after the local
verification;
NO (only net), that is, only the background verification;
LN (local net), that is verified after the first local background
72
TFT Fingerprint V6.3
verification.
Note: Remote verification function only with certain models.
Press the number keys to type a verification server's IP address,
Scroll / button to select methods of verification. After the set,
directly press OK button or menu button to save your settings and
return to the previous interface, Press “ESC" to cancel and return to
setting interface.
Remote fingerprint registration
Change the verification model to NL / NO / LN, start the
background authentication server procedures, remote registration
fingerprint registration button will appear on the equipment user
interface, you can achieve remote fingerprint registration
73
TFT Fingerprint V6.3
4.3 Wireless settings★
Scroll "▲ / ▼" button to select dial-up settings, click "OK" button
to enter settings
Before the equipment apply to wireless Network, another physical
component of that 802.11 network consist Distribution system,
Access Point, Wireless Medium must exist.
You must know the ESSID (name of network) of local network you
want to connect to
Wireless Network ID: local wireless Network that you want to
connect with (capital letter and small letter is different)
Network model: there are two option , Infrastructure Model, and Ad
-hoc Model; this Infrastructure Model will apply to Hub and
Spoke wireless network, the Ad-hoc Model is used in the peer to
peer wireless network..
the Authentication Type: The Infrastructure Model include five
Authentication Type that are OPEN 、SHARED、 WEPAUTO、
WPAPSK、 WPA2PS.
the Ad-hoc Model include OPEN 、SHARED、 WEPAUTO
WPANONE four type of Authentication Type.
Encrypt Type: When the item NONE of encrypt Type is selected,
then the password in WEP (Wired Equivalent Privacy)
and WPA (WiFi Protested Access) item is not permitted
to modify it, it is not need to input password too.
74
TFT Fingerprint V6.3
This PC IP address: If there is the DHCP function in the 802.11
network Distribution system, you may choose DHCP, press OK to
exit.
Otherwise, type in the IP Address,Subnet Mask blank with the correct
figure, press OK to exit to main interface.
Instruction
Scroll▲ / ▼ key to locate the cursor in the inputting box or the
button , start the T9 inputting method, type the network identify
ID, must correctly enter network identification ID , otherwise it
will be unable to move the cursor to the other input box, through
scroll / button to select the Items that need to input. Directly
input value.
Set a password:
75
TFT Fingerprint V6.3
According to the choice of authentication methods and different
forms of encryption, password interface are also different. There
are two settings WEP and WPA available.
WEP password
Type the password to meet the requirements, the WEP password in
the four groups’ password, if the four groups have been set up and
are the correct password, only the currently selected password take
effect.
Assigned IP:
It specified equipment in the IP of wireless network. And
communications in the network settings is not associated
/ "OK" (F7) button to save your
After the set directly press
settings and return on an interface, press the "ESC" (F8) to cancel
and return to previous interface.
4.4 Available wireless network★
Search the wireless signal can be received by equipment in the
current environment and view the strength of signals, to help users
find the network he/she need quickly and easily
76
TFT Fingerprint V6.3
Press F6 key to refresh the list.
Press F7 key to set the selected wireless network parameters.
4.5 dial-up settings★
Scroll "▲ / ▼" button to select dial-up settings, press "OK" button to
enter settings.
1, SIM card slot
Plug the SIM card into the slot until the equipment lock SIM .
77
TFT Fingerprint V6.3
2, dial-up settings
When equipment is used in the dial-up network, please ensure that
the equipment is covered in a GPRS or CDMA signal, and it is
necessary to know the used modem types, APN name, and access
numbers.
Modem type: According to the SIM card type of equipment
installed, choose the optional modem types.
Frequency: Local wireless network provider supply Network
frequency.
APN name: Access Point Name, "access point name", used to
identify GPRS / CDMA provider.
User name and password: verify whether the user have
permission to use the network.
Access Numbers: GPRS / CDMA dial –up number.
Redial interval: If after the network is disconnecting from time to
time, it will automatically redial interval.
The number of redial-up times: If after the network disconnecting
78
TFT Fingerprint V6.3
the numbers of the equipment try to redial up the network.
Instruction
Scroll ▲ / ▼ key switch box or enter the cursor to the button to
start the T9 input method type APN name or user name, the other
way that through the input box scroll / button to select the
items need to, or directly type a numeric value. After the set
directly press
/ "OK" (F7) button to save your settings and
return on an interface, press the "ESC" (F8) to cancel and return to
previous interface.
Server Settings
Set server parameters of Equipment, the server is used for the
collection of equipment time and attendance records (the installed
server on the companies provide data collection software), set up
79
TFT Fingerprint V6.3
after the right equipment will be automatically sent the server time
and attendance records.
Keep online: equipment is maintained online.
Upload interval: after passing a defined of period time, the
attendance record will be automatically uploaded to the server by
equipment.
Search way: choose to use GPRS or LAN way to search.
Search interval: after pass period of time, the equipment will
automatically search.
Address Type: Set type of the server's address and assign the
values.
Instruction
80
TFT Fingerprint V6.3
Scroll ▲ / ▼ switch the cursor keys to enter the box through /
button to select the items need to, or directly enter a numeric value.
After the set directly press
/ "OK" (F7) button to save your
settings and return on an interface, press the "ESC" (F8)to cancel
and return to previous interface.
3, GPRS usage
1) dial-up
After setting. Make sure to restart the equipment, the equipment
will automatically dial-up, dial-up successfully, GPRS icon will
appear on the bottom of the screen:
2)data download
after Dial-up successfully , on the server start the download data
program, when the staff verified successfully on the terminal, the device
will automatically send data to the server, while is downloading, the
81
TFT Fingerprint V6.3
interface prompt is "in communications……";
If fail to download, the interface will appear as follows:
82
TFT Fingerprint V6.3
4.6 Wiegand input settings
★
Scroll"▲ / ▼" button to select Wiegand input settings, press "OK"
button to enter settings.
Customized format: the input format of Wigand is definite by
user-self.
Bit digit: bit of wiegand data length.
Pulse Width: refers to the Wiegand pulse width by the default is
100 microseconds, can be adjusted within the scope of 20-800.
Pulse interval: the default value is 900 microseconds, can be
adjusted between the 200-20000.
Enter content: wiegand input signal contained in the content,
choose to include work code, or card number.
Note: Wiegand input settings function only provide with by certain
models
Instruction
83
TFT Fingerprint V6.3
Enter the name of self-definition format, Scroll ▲ / ▼ key to
move the cursor to the items to be set up. If it is the input box,
input to provide value with the small number keyboard,If it is a
rolling box, scroll / key to switch and set its value, after
complete setting, directly press the menu keys to save setting and
return the previous interface, press the "ESC " button to Cancel
and return to the previous interface.
4.7 Wiegand output settings
★
Scroll "▲ / ▼" button to select Wiegand output settings, press
"OK" button to enter settings.
Format: refers to the built-in system has been defined format, users
do not need to specify the total length of all information and the
84
TFT Fingerprint V6.3
location.
There are 4 definition format by the system default: wiegand26
with sitecode, wiegand34 with sitecode, wiegand26 without
sitecode, wiegand34 without sitecode. wiegand26 with sitecode
refer to the wiegand format the equipment sent contains 8 bit
for the facility code field . wiegand26 without sitecode without
refer to the W26 format output without the facility code field. If
there is no the facility code field setting, the output signal does not
contain this information, if set up a site code, the output is set a site
code (similar to machines ID, this is different from the user's own
code is designated, and Can be repeated in the different machines,
the range between 0-255).
Failure ID: after the failure to verify, the failure of ID number will
be sent, when the option is invalid, do not sent. Range between
0-65534.
Site Code: similar to machines ID, this is different from the user's
own code is designated, and can be duplicated for the different
machines, the range between 0-255.
Pulse Width: refers to the pulse width of Wigand signal the default
Width is 100 microseconds, can be adjusted within the scope of
20-800.
Pulse interval: the default interval is 900 microseconds, can be
adjusted between the 200-20000.
Output: wiegand signals contain the content, there are option to
include work code, or card number.
85
TFT Fingerprint V6.3
Note: Wiegand output function only provide with by certainϑ
models.
Instruction
Scroll ▲ / ▼ button to move the cursor to the item to be set up. If
the input box, click on the number keys keyboard input to set the
value if the rolling box, scroll / button to switch to the value of,
for example, the failure ID was revised to 10, press / button to
set the options to open, then enter10 to the box. After the set
directly press
/ "OK" (F7) button to save your settings and
return on an interface, press the "ESC" (F8) to cancel and return to
previous interface.
86
TFT Fingerprint V6.3
4.8 Print Settings
★
Scroll"▲ / ▼" button to select print settings, press "OK" button to
enter settings.
Printer: there are total of seven kinds of optional print mode.
Note: 1, attendance status shows: I indicate Check-In, O indicate
Check-Out, T indicate BreakOut, B indicate Break-In, i indicate
OT-IN, o OT-OUT.
2, if no special note, the date -> with the same date format
of the machine setting, the time format: HH: MM: SS.
3, without special note automatically print.
a. Mode 1:
Employee No. , machine ID, date, Time, attendance status
b. Mode 2:
ID.NO: Employee No.
Date attendance status
Date Time
c. Mode 3:
machine ID Name, date and time
d. mode 4 : (Note: the time format: HH: MM; date format: DD /
MM / YYYY)
Control Asistencia
==================
87
TFT Fingerprint V6.3
Attendance status
Date Time .....
Codigo ..... workers,
===== Gracias =====
e. mode 5 : (Note: 1, after verification successfully will prompt the
need to print. 2, the time format: HH: MM)
Date, time, attendance status
VO
f. Mode6:
ID USER: Employee No.
Date attendance status
Date Time
VO
g. Mode7:
Usr.ID: Employee No. ,
Nombre: Name
Fecha / Hora: attendance status
Date Time
Note: 1, the printing function only provide with by some models,
and the Chinese machine does not support this feature.
2, the baud rate of fingerprint machines and printers (Super
Terminal) must be consistent.
88
TFT Fingerprint V6.3
3, if the default print format can not meet your requstment, and
please contact my company business representative
Instruction
Scroll / button to select print mode, after set up directly Press
OK button or menu button to save your settings and return previous
interface, press "ESC" to cancel setting and return to previous
interface.
89
TFT Fingerprint V6.3
5 User profile
User Profile settings can be set up according to their personal
preferences show some style and operation method.
5.1 User Customize
According to their personal preferences, users can set up the initial
interface style.
the times of retrying 1:1 verification or password: users go on
1:1 verification or password, who may forget the right registered
finger or improperly press fingers. The setting provides user with
convenience, and reduces to repeat keys, makes the user to retry the
verification after failed to verify within the limited times.
Clock options: When the user is going on the verification
operation, regardless it is success or failure, the Clock pattern will
display you choose on the screen after verifying.
90
TFT Fingerprint V6.3
Public Photo: according to the actual demand, users can upload
some public photographs to be displayed on the screen.
1) Photo cyclical interval : how long the interval to shift Photo
Display (Scope for 3 to 999 seconds)
2) Duration of the clock showed that after the user is verified how
long the clock pictures show. After a show duration, the initial
public photos will be displayed on the interface. (Scope 0 ~ 999
seconds, 0 clock that has been shown.)
Timing Sleep: When the equipment was not operating in the state
to set up a regular sleep time after the equipment will enter a
dormant state. Pressing any button or touch fingers that can awake
up the equipment.
Screen brightness adjustments: adjust TFT screen brightness.
Fingerprint Image Display: whether register or match the
fingerprint image will be displayed on the screen. There are four
options: register and match, only match or register not to display.
Locked shut down key: choose whether or not to lock off button.
As a "yes", press shut down key invalid. As "no", press shutting
down key shutdown after three seconds.
Background standby mode: When the equipment in a standby
status, there are t three kinds of choice background pattern: First,
publicity picture, second play the background music. the third is
flash player.
91
TFT Fingerprint V6.3
Attendance camera mode: When the staff punch-in./out, whether
capture and save the current staff ‘s photo. Here are the settings
for all staff.
A total of four kinds of patterns
Photo: when track staff attendance, taking his/her pictures but does
not save photos.
Do not take photographs: when track staff attendance , not to take
photographs.
Take pictures and save: when track staff attendance take and save
his /her photos.
No passed and save: when track staff attendance staff failed to
pass verification three times, the camera take his/her photo and
save it.
Note: If the duration of the clock display is set to 0, in ready
working state the machine plays full-screen flash; if set to other
values, it plays the small screen flash in ready working state.
Instruction
92
TFT Fingerprint V6.3
Scroll the / key to choose the box you need input the value with
small keyboard, after finishing the setting, please directly press OK
(F7) key to save this item and return to preceding interface,
or
or press the ESC (F8) key to give up operation and return to
interface.
5.2 Video Setting★
The built-in camera equipment parameter settings, the camera will
have the best performance.
Brightness: Adjustment the brightness of camera capture photo.
Contrast: Adjustment the contrast of camera capture photo.
Picture quality: Setting up quality of the saved picture .
93
TFT Fingerprint V6.3
Environment: Setting up the filming environment in which to take
effect as the best.
Restore Default: the parameters of the above-mentioned parameters
restored to the default values.
Scroll ▲ / ▼ key switching options input box with the small
keyboard and input appropriate number keys to adjust the value of
the camera , or press the button will restore the default parameters
and restore to the default state. After appropriate adjustments by
(F7) or "OK" Save settings, press the "return" from set.
Note: the setting is just available to the unit which has camera.
5.3 Screen Calibration
If the touch screen is not sensitive enough to induce the touch, the
94
TFT Fingerprint V6.3
screen induction calibration can be adjusted in the menu.
5.4 Bell Setting
Ringing bell to notice people to work is a widely measure in many
companies. In tradition, there are two measure to do it by man or
with the help of electronic tool. In order to get an economic and
convenient management, the time bell function is available in the
fingerprint machine. With the schedule bell function, the fingerprint
machine will automatically make bell sound during a certain time
which is set in advance; when the certain time ends, the bell will
automatically stop sounding.
Instruction:
Scroll ▲/▼ key to view the bell setting at line by line.
95
TFT Fingerprint V6.3
Scroll F5/F7key to view the bell setting in page by page.
Press "
" key to begin/end the selected bell.
Press "OK"/F5 to choose one of the bell setting, and enter the
edition bell.
Bell time: time out, bell rings;
Sound choice: different sound in different time.
Volumes adjust: Bell sound volume.
Number of times: times of bell ringing
Bell state: start this bell or not.
Scroll the▲/▼key to shift the cursor to input box, set up the value
with the numeric keyboard input. After the setting, directly press
96
TFT Fingerprint V6.3
OK or the
/“OK”(F7) key to save the settings and return to
preceding interface, press the ESC(F8) key to give up.
5.5 The Definitions of Keyboards
5.5.1 State Key Definition
Customize the attendance state key in the equipment, after pressing
the corresponding state key again, the attendance log is recorded in
this state key.
When press any state key on initial interface, the attendance state
corresponding to the state key will appear under the leftside of the
screen, that is convenient for users to check.
Instruction
97
TFT Fingerprint V6.3
Scroll the ▲/▼ key to shift option box, Scroll /
key to change
/“OK”
the setting. After the setting completed, please press
(F7) to save this configuration, press the ESC (F8) key to give
up the operation and return to the interface.
Note: If some state keys would not be used, then set the state keys
as invalid.
5.5.2 shortcut definition
The definition of shortcut, that is the buttons can be defined as the
attendance status shortcuts or view function shortcuts. On the
standby equipment interface, press the corresponding button will be
displayed attendance status or rapid access to interface functions.
98
TFT Fingerprint V6.3
Instruction
Scroll ▲ / ▼ key to scroll shortcuts definition line by line.
Press F6/F7 keys to scroll shortcut definition page by page.
Press F5/OK key to edit the selected shortcuts.
5.5.2.1 set up shortcuts
Select a shortcut, press F5/OK into the editing interface.
Function: Set shortcut. Including the state key, work code, read a
short message.
If choice is the key state the following options appear: Code: assign
a code to the state keys to facilitate the statistical record of view.
99
TFT Fingerprint V6.3
Name: The keys expressed by the state's name.
Automatically switch: When reach the time you set, the device will
automatically switch state.
1)
set to function keys
Instruction
Scroll
/
key to set "#" key as the help button.
2) State key setting
100
TFT Fingerprint V6.3
Scroll ▲ / ▼ key to switch option input box, press the number
keys on the keyboard, or scroll / key to select to the set value.
After setting, a direct press
button to save your settings and
return to the previous interface, press the "ESC" to cancel and
return to previous interface
5.5.2.2 Usage of shortcuts
1)State Key
On main interface, press “F5”, the corresponding state key will
appear at the left bottom of the screen.
101
TFT Fingerprint V6.3
Then user can do the verification by fingerprint or password, the
equipment will keep the attendance record at the corresponding
state
2) shortcut function
For example, in the setting “*" key is set to view the short
message.
When there is a short message in the equipment, press "*"
button on standby interface, the short message
102
TFT Fingerprint V6.3
6 Inquiry Record
Inquiry the attendance records for, attendance photos and other
information that is saved in the machine, to facilitate the
management staff to keep track of attendance situation.
Scroll ▲ / ▼ button to select the contents to query, press "OK" to
start enquiry
6.1 View attlogs
If the fingerprint machine successfully record the staff time &
attendance, the record will be saved in. the inquiry record function has
been designed in simple and manner to help user find his/her attendance
103
TFT Fingerprint V6.3
logs he/she need quickly and easily. this machine offer the inquiry
function. Different ways are available in unit to check the users’ logs.
Enter the attendance inquiry menu, the first box is used for inputting
condition. Enter the ID No. and the Data:
1) All AC. No, that inquiries all staff.
2) Import a certain ID.NO, only for the certain staff attendance record.
Press
/ "OK" (F7) key to inquiry, the records that meet you
input condition will be displayed on the screen.
104
TFT Fingerprint V6.3
Scroll ▲ / ▼ key, move the cursor on the line you want, press
/“OK”(F5) to enter attendance record Details view.
For example, on August 28 on the 1st staff, Press Details to check.
105
TFT Fingerprint V6.3
If the records fulfill the first page, press F6/F7 to turn on next page..
Press the "ESC" (F8) to return to the previous interface.
6.2 View Time &Attendance Photo★
If this mode is set, as the fingerprint machine is able to take
employee photo and save it, while staff punch-in /out, after tracking
staff time and attendance successfully, the taken photos will be
saved. Here you can query these photos.
Enter to view time &attendance photo mode, first you will find the
input box for query condition.
106
TFT Fingerprint V6.3
Input the Employee No. you want to query:
1) if your choice is all employ NO, that for all employees.
3) Enter an Employee No., only this staff’s attendance photo is
allowed to view.
Enter whether query all the photos, if your choice is no, then
enter the date range to query.
Press
/ "OK" (F7) began enquiry, after the completion of
enquiry, the photo that meets the conditions will display on the
screen:
107
TFT Fingerprint V6.3
Scroll F3/F4 keys to view the attendance photo that save in the
equipment , the total number of photos and which photo is
present now are shown by photo below, and the day and time that
the pictures were taken are displayed.
6.3 View the blacklisted photos★
If attendance camera mode is set to take pictures and save or not to
save, the staff failed to pass attendance verification, the fingerprint
machine camera capture his/her photos and save it, these photos are
called blacklist photo, here you can query these photos.
Enquiry photo in the blacklist, the first is query condition input
box.
108
TFT Fingerprint V6.3
Enter whether query all the photos, if your choice is no, then enter
the date range to query.
/ "OK" (F7) began enquiry, after the completion of
press
enquiry, these photos that meets the conditions will display on the
screen:
109
TFT Fingerprint V6.3
Scroll F3/F4 keys to view the attendance photo that save in the
equipment , the total number of photos and which photo present
now is shown by photo below, and the day and time the pictures
were taken are displayed.
110
TFT Fingerprint V6.3
7 USB Flash Disk Management
Using USB flash disk is able to download user’s information,
fingerprint templates, attendance logs, and upload it into the
tracking software for processing. Mearwhile, user’s information
and fingerprint templates are able to upload into other fingerprint
equipments. When the font of button display in blue color , means
that the device does not support this function, this function is not
available.
Instruction
111
TFT Fingerprint V6.3
7.1 Upload User data
Upload user’s information and fingerprint templates which have
been saved in the USB flash disk into the equipment.
Instruction
Plug the USB flash disk into the USB slot of the fingerprint
machine, scroll "▲/▼" key to choose the user data that you want to
upload, press the OK key. The two files, user.dat (user information)
and template.dat (fingerprint template), will be uploaded to the
machine. If the two files in the USB flash disk are not complete,
the prompt "failed to deal data, check your U flash disk ”.
7.2 Download User’s Data
Save all user’s information and fingerprint templates from the
equipment into the USB flash disk.
Instruction
Operation is similar with the attendance data.
Plug the USB flash disk into the USB slot of the fingerprint
machine, Scroll the "▲/▼" key to choose user data you want to
download, if download successfully , the files user.dat (user
information) and template.dat (fingerprint template) will be viewed
availably
7.3 Upload the Customized Picture
Upload the file with JPG picture format which front name as "ad_”
112
TFT Fingerprint V6.3
in the USB flash disk into the equipment, after these pictures have
been transfer to the equipment, it will display in the initial window.
(Picture specification, please see appendix 4)
Instruction
Plug the USB flash disk in the USB slot of the fingerprint machine,
scroll "▲/▼" key to preview the picture in the USB flash disk then
press the OK key to choose the picture you want to upload. If the
prompt “upload successfully” is displayed on the equipment, the
file will automatically jumps to the next picture. After completing
uploading the pictures, press ESC(F8) key to exit.
113
TFT Fingerprint V6.3
7.4 Download Attendance Datum
Save all attendance datum from the equipment into the USB flash
disk.
Instruction
1) Plug the USB flash disk into the USB slot of the fingerprint
machine through the mini USB cable.
2) Scroll“▲/▼”to select the “ Download Attlog”.
3)Press “ok” to go on downloading data, the equipment prompt "is
downloading , please waits... ...” until the equipment prompt
“download attendance data successfully".
4) Press “OK” key to exit from this interface. Take out U flash disk.
The files X_attlog.dat (attendance log), X_oplog.dat (management
log), and X_user will be saved in the USB flash disk(X is a symbol
of machine No.)
7.5 Users Upload Photos
Upload the JPG picture file which is named by ID.NO in the U
Flash disk. After upload, while the staff finish verification, the
staff’s photo will show in the display
Insert the U flash disk into the USB slot of the fingerprint machine,
Scroll "▲ / ▼" key to preview the qualified pictures in the U flash
disk, find the favor pictures , press "OK" button to upload. When
the equipment promt successful uploading, it will automatically
turn to next picture. Complete uploading, press the "ESC" to exit.
114
TFT Fingerprint V6.3
7.6 Download User’s Photos★
To save staff photo which is taken by the equipment into U flash
disk.
Instructions
Insert U flash disk into the USB slot of the fingerprint machine,
scroll "▲ / ▼" button to select user’s pictures. If the user picture
was downloaded successfully, it will be found in disk.
7.7 Upload Short Message
Upload the short message from the U flash disk into equipment.
Instructions
Insert the U flash disk into the USB slot of the fingerprint machine,
Scroll "▲ / ▼" button to select user upload datum. Press "OK"
button, the two files, udata.dat. and sms.dat, will be uploaded to the
machine.
7.8 Download Short Message
Short Message in the equipment can be saved in the U flash disk .
Instructions
Insert the U flash disk into the USB slot of the fingerprint machine.
Scroll "▲ / ▼" button to select users download data. Press "OK"
button, the two file, udata.dat. and sms.dat in the machine will be
downloaded to the disk.
115
TFT Fingerprint V6.3
7.9 Upload Flash
Before you upload the Flash file into the equipment, please contact
our technical support. Our support will make it to meet your
demand, to support you upload the documents through U flash
disk.
7.10 attendance photo download
★
Download photos and blacklist photos, which is taken while
employee punch-in/out and save in the equipment to U flash disk,
the photo format is JPG format.
Instruction
Insert U flash disk into the USB slot of the fingerprints machines,
scroll "▲ / ▼" key to select attendance photo to download.
116
TFT Fingerprint V6.3
Attendance photos downloaded: will only download the attendance
photos to the U flash disk.
Blacklist photos downloaded: only blacklist photos download to
the U flash disk.
Whether Delete the downloaded photos: Set as "Do not delete the
downloaded photos," After the download is complete, the
equipment are still store photos.
Set as "delete the downloaded photos", downloaded the photos will
be deleted, after the download is complete. scroll "▲ / ▼" button
to select the type of the photos to download, scroll / key to
choose whether delete the downloaded photos. After downloaded,
which the first directory is pic_ machines ID, the second
subdirectory pass is used to store attendance photo, the second
subdirectory Bad is used to store blacklist photos.
117
TFT Fingerprint V6.3
8 Information Release
The short message is similar to bulletin and notice. With the
function, operator is able to schedule and edit the content of the
short message that will be displayed on the screen. The short
message is consisted of public short message and individual short
message. If the public short message is configured, the icon
will display on the information bar of the window in the assigned
time. The default key is "#" key (customerized keyboard) which is
available to the short message content. If the individual short
message is setted, the system will show the short message to the
staff after the staff verifying successfully.
Instruction
118
TFT Fingerprint V6.3
Scroll ▲ / ▼ keys to read his party Short Message.
Press F6/F7 keys by reading a chapter in the short message.
Press "OK" / F1 to view the selected Short Message Details.
Press F2 to view new short message.
Press F3 to edit short message.
Press F4 to delete Short Message
8.1 Establish Short Message
1) Add short message
Press F2 key to add short message in the pop-up menu..
Start time: the time the short message starts.
Show period: within the show period the short message will be
displayed; after the period, the short message will stop.
Message type: Individual: only for individual
Public: All people are able to see.
Initialization: the initial short message, that means
no individual and public short message.
Instruction
119
TFT Fingerprint V6.3
When the cursor locate in the text box, press “*”key to open the T9
input method, input the content of the short message, scroll the ▲/
▼ key to switch the input box, scroll
/ to change setting or
keyboard and input the value with the small numeric keyboard.
(1) If the type of individual short message is your choice, the
distributing button is available; here the individual short message
will be distributed to the staff
120
TFT Fingerprint V6.3
Scroll ▲/▼key to search personnel line by line .
Press "OK" key to choose the personnel, then short message will be
released to this staff.
/F7/F8 key to save your choice and exit.
Press
Note: Before finishing the steps, please do not exit, or the setting
will not work and turn to the initialization.
(2) while in public short message or initialization, the distributing
button will not work. After completing the setting, press
/F7/F8 key to save it and return to the short message list.
2) Edit short message
Press F3 key to edit short message.
The operation to edit the short message is same with one to add the
short message.
3) Delete Short Message
121
TFT Fingerprint V6.3
Press F4 key to delete the short message.
Device will prompt “Are you sure to delete this short message? :
Press “OK” to confirm the delection, press “ESC” to give up the
operation
8.2 View Staff Short Message
1) Check the public short message
While the public short message is working, the main interface
show the picture and the content of the message, the interval
display time will turn around with advertising picture, if there are
many short messages, please scroll ▲/▼ keys to read
2)Examine individual short message
If the user who has the message verified successfully, the short message
content will be displayed.
122
TFT Fingerprint V6.3
The duration of the message display is 30 seconds, after the
message, the user verification begins working.
123
TFT Fingerprint V6.3
9. Systems Information
From system information icon, you are able to know the
information about the device, like Free volume and Engaged
templates.
9.1 Equipment Information
In the equipment information, there are the equipment name, serial
number and firmware version.
9.2 Logs Capacity
Through the log capacity you can check the number of users,
managers, registered password in this machine; the machine
provides the vivid graphic of fingerprint capacity, attendance logs
capacity in order to show the free capacity and the used capacity of
each item.
124
TFT Fingerprint V6.3
125
TFT Fingerprint V6.3
Appendix 1 Getting Familiar with Keyboard
The equipment keyboard has different usage in different interface, for
details please see the next table.
Key
Detailed solution
numeric
keyboard
1, 0 ~ 9, is used in to input the staff to number, numeral
and password so on.
Function
Key
1. Main menu , that is used as attendance state key.
2. The shortcut key, if there is operation item in the
screen ,and relate the button position
▲
1、Upward .
2、Upward/forward switch option
▼
1、Downward.
2、Downward/Backward switch option.
1、Revision current value.
1、Revision current value
1、Shut down key. Keep press the key for 3 seconds in the
initial interface to shut down the unit.
1 、 Backspaces key. While inputting wrong ID.NO,
password, system setting value, press the key to
delete the value.
menu key,confirms ESC key
OK
ESC
Confirm and save
1、Cancel operation and return to the preceding of menus
126
TFT Fingerprint V6.3
2、Press ESC key to close T9 input method
*
1.start the T9 input method
#
1.The backspaces key in T9 input method
127
TFT Fingerprint V6.3
Appendix 2 T9 Input Method
T9 input method is a intelligent input method; it is famous for
highly effective inputting the character. The equipment fully supports T9
with Chinese, English and symbol input. There are three or four English
letters on 0 ~ 9 numeric keyboards of the machine, for example the
numeric keyboard 1 has the A, B, C three letters, only input key where
this letter locate for the T9 Chinese, the program will automatically
spell Pinyin. Then press the numeric key to choose Pinyin to input the
Chinese character. T9 English also comply with the letter arrangement
of English word to input, only press key, then the program automatically
display this key expressing all letters, press the numeric key to select the
letter. T9 input method can support inputting some marks. User is able
to input the name and the short message content by using T9 input
method key.
T9 input method key distribution and its function as blow:
ESC key
Backspace
Start the input method
Spacebar
128
TFT Fingerprint V6.3
▲/▼/ / : Turn page key
OK: Choose letter
Take an example for the T9 English input: Input “Ja "
press the * numeric key to enter the T9 input method.
129
TFT Fingerprint V6.3
Scroll / key or input the letter you select.
Press 1
If the operation must be carry on, please use the above method to
do it again. After the input is completed, press the ESC key to exit
130
TFT Fingerprint V6.3
Appendix 3 Quickly Inquire Staff Attendance
Logs
In order to help ordinary user to view his/her Time & Attendance
record at same time, whether forgetting clock-in or occurring error,
should well inform the supervisor that the attendance record is in
abnormal.
Instruction
After the machine verify fingerprint or the password successfully in
10 seconds, then pressed “OK”/
records at same time.
key to ability show this staff all
For example: the staff, who’s ID.NO is 1, match the fingerprint
successfully, then the press “OK”
key, you ability to view his
/her Time & Attendance record at the same time.
131
TFT Fingerprint V6.3
Scroll the ▲/▼ key to browse the Time & Attendance record line
by line
Press F6/F7 key page by page to browse the Time &attendance
record;
Press “OK’ or
key show detailed inquiry.
Press ESC/F8 key to return the initial interface.
132
TFT Fingerprint V6.3
Appendix 4 The Rule about the Advertising
Pictures
Custom Photo specifications:
1. Photo format is JPG format to the other formats Do not support
the format of photographs must be "ad_" as its head. For example
ad_12.jpg is legitimate.
3.After photo is uploaded , the file name is not changed, following the
replacement of the second pictures. You can upload pictures with the
names of the coverage.
4. The size of each picture can not be more than 200 K, otherwise they
can not be uploaded.
5. Picture resolution is 800 * 555 high-width, preferably not more than
or less than the resolution
6.Only maximum photos: 16
Users upload photos:
Firstly upload pictures to equipment with U flash disk. After uploading
and machine verifies fingerprints, photo will abilityshow at same time .
1. User photos must be JPG format, the file name, must be named. For
example: the 154 users of the corresponding photos is 154. Jpg.
2. Because limit by this version, the names of user photos only no more
than eight digital, such as: 12345678. Jpg is legal. On this issue, we are
deeply sorry about the inconvenience caused to you and we will be fix
this problem in next version.
3. Before uploading , the file folder that is called as “photo” in the U
133
TFT Fingerprint V6.3
flash disk must be established, all users need upload photos within this
folder.
4. while uploading, insert U flash disk into USB slot of the fingerprint
machines, scroll the "▲ / ▼" key to preview qualified photographs in U
flash disk, select the photos you need to upload. If you need to upload
all photos in the U flash disk, select "Upload user data."
5. When downloading, will be automatically built a folder called photo,
users can download all the pictures within this folder.
6. If you need to download all photographs in the machines one time,
select “Download user data."
134
TFT Fingerprint V6.3
Appendix
5
Take
photo
while
staff
punch-in/out★
When tack employees attendance, the camera mode is set to take photo /
photo and save / failed to pass no save, To track staff attendance process
as follows (take 1: N fingerprint verification as an example):
Step 1: Use the properly way to place finger on the windows of the
sensor.
Step 2: If successfully validated, equipment start capture the current
photo, photos will display on the screen. (If the photo that user
have registered will be shown on upper left corner, are not
registered are not shown)
135
TFT Fingerprint V6.3
Step 3: When the equipment prompt, "Thank you", (If the photo that
user have registered will display photos), the certification
completed.
136
TFT Fingerprint V6.3
Step 4: When verification is unsuccessful, the equipment and start
camera and take photo to display on the screen.
Step 5: the equipment prompt “please try again”, please return to step 1,
try again.
137
TFT Fingerprint V6.3
Appendix 6 Battery specifications and Notice★
Maximum output voltage
DC15.0V
Output voltage
DC12.0V
Rechargeable power supply specifications
DC12V - 1.5A
Cycle life
The number of charge-discharge cycle ≥ 500
Charging time (H)
3.5 ± 0.5
Discharge time (H)
138
TFT Fingerprint V6.3
3.5 ± 0.5
Storage Environment
Temperature: 15 ° C to 25 ° C
Relative Humidity: 45% -75%
Battery specifications
Notice
1, when batteries is in use, please Do not plug and pull power supplies
too frequent (2-3 seconds), maybe cause failed to recharge;
2, Do not use the battery in a very hot environment, , such as direct
sunlight. Otherwise, the battery will overheat, might fire (fire), it will
affect the performance of the battery and short the life s of batteries used;
3, the battery has vent fluid, electrolysis also caused eye, skin or
clothing, immediately wash with water flow, or seek immediate medical
assistance;
4, please correct for battery installation and dismantling, otherwise it
will affect the performance and battery life.
Caution:
There are dangers of battery exploding, leak, fever, fire, break if
you don’t read the notice carefully.
l Do not put the battery into water or let it to get wet.
l Do not use and store battery near heat-generating device
( such as fire or heater).
l Please use original charger only.
l Do not inverse polarity connection.
l Do not throw batteries into fire or hot battery. Do not use wire
or other metal short the positive and negative terminal, donot transit or
storage it with necklace, barrette and other metal object.
l Do not break battery cause short-circuit battery
139
TFT Fingerprint V6.3
l Dropping a battery may cause a strong physical shock that
may damage the performance of the battery
140
TFT Fingerprint V6.3
Appendix 7 About Anti-pass back function★
.
[Summary]
If you want to prevent from somebody follow the others to enter the
building, do not go out together, which cause the potential safety
problems, this feature Anti-pass back function is designed to save this
problem ,unless the access records must be matched, the door is unable
to be opened.
In order to realize this feature, reques two access control machines t . A
machine installed in the building inside(the "Master"), a machine
installed in the building outside (hereinafter referred to as "slave").
Between the two machines communicate through Wiegand signals.
[Principle]
141
TFT Fingerprint V6.3
the Master machine provide with Wiegand In signal, the Slaver
machine own Wiegand Out signal. Connect Wiegand Out of the slaver
machine to the Wiegand In of master machine, Wiegand signal sent out
from the slaver machine must be non-machine ID, the number that send
it to master machine must exist in the master machine, that is the users
of two anti-pass back machines must match.
[Instruction]
According to the most recent user access records, the fingerprint
machine determines whether start anti-pass back function or not, access
record must be matching. This machine supports, IN, Out, IN-Out
anti-pass back.
When the Master machine is set to "Out- anti-pass back," If a user
attempt to normally access, then his/her the last record must be "in" can
not be out. As long as it is to find the record is “Out”, system will be
refused by "anti-pass back " For example: a user's most recent record is
"in", it is allowed to the second record is “in” or “out” . the third record
must based on the second record, “In” and “out” must be matching,
and so on. (Note, if there is no record of prior customers, and that he can
In, not out)
When the Master machine is set to "In anti-pass back," If a user attempt
to normally access, then the last record the user must be "Out" ,
otherwise it is not allowed to go out. As long as it is to find the records
system will be refused by "anti-pass back." (Note, if there is no record
of prior customers, he can go out and can come in)
When the host is set to "In-Out anti-pass back," If a user attempt to
normally access , then is the most recent record the user is "Out" and
142
TFT Fingerprint V6.3
"in", the next record is to be "in" and "out", these “In” and “Out” record
must be matching.
[Instruction]
1)
The choice of Machine models
Master machine: the machine with wiegand in . except for F10 .
Slave machine: the machine with Wiegand Out .
2) Setup the menu
Anti-pass back direction
The choice of Anti-pass back mode. There are three options: In anti
pass back, Out-anti-pass back, None-anti-pass back.
In anti-pass back: Only the user's last recorded is “In”, can open the
door.
Out-anti-pass back: Only the user's records in last time is “out”.
Machine state
There are three options: control In, control out, None.
Control In: Set the value, the machine records to verify the entry
records. Control out: Set the value, the machine records to verify the
records out. None: Set the value, that is, the closure of the anti-pass back
function.
143
TFT Fingerprint V6.3
Scroll ▲ / ▼ key switch input box option, press / to change
settings, after the completion of setting, press the menu button to save
your settings, press "ESC" to exit the setting.
3) modify machines weigand output format
Two machine communication, only the Wiegand signal without
machine No. is accepted by the machine. may enter the menu of
machines -> Communications Settings -> Wiegand settings or enter
the software -> basic settings -> equipment management -> weigand,
"defined format" to "wiegand26 without device ID".
4) User registration
This user must also exist in the master and slaver machine , but
users ID must be consistent. Therefore, need to register users in master
and slaver machine at the same time.
5) Wire instruction
Weigand from the main machine for communication, wiring as
follows:
144
TFT Fingerprint V6.3
From the host machine
IND0 <-----> WD0
IND1 <-----> WD1
GND <-----> GND
145
TFT Fingerprint V6.3
Appendix 8 Multi-combination Authentication
Mode★
Besides this function only is owned by the fingerprint access
control machine that has been appointed, the most fingerprint
machine only has two way to verified by fingerprint and password,
we provide a personal or group Multi-combination Authentication
Mode for high security Access control area, verification type main
include four elements that are Employee Number PIN, Fingerprint
(FP), Password (PW) and RF card (RF), which can combine into
filth multi-combination.
Note:
The fingerprint machine with Mifare function needs to verify
Mifare card.
The Mifare card is regard as RF card in the verification procedure,
the function of Mifare card verification only is validity in the
machine which Mifare card function is provided with.
These symbols illustrate what follow the table different means.
● “/” is or,
● “←” is confirm (Enter),
●”+” follow next operation
● “&” is and,
● FP (fingerprint)
● PWD (Password)
● RF (RF card)
● PIN (user ID)
If fingerprint or Password has been used to enroll user, the
146
TFT Fingerprint V6.3
verification procedure is follow
Type
FP
What you do
Only fingerprint is verified.
1) PIN+FP(1: 1Verification)
2) FP (1: N Identification)
3)RF+FP(1:1)
PIN
Only PIN is verified
1)PIN( just have to input the digital through keyboard)
PW
Only verify password is verified
1) PIN+”←”+PW
2) RF+PW
RF
Only RF card is verified
1)RF
FP/PW
Fingerprint or Password is verified
1) PIN+FP(1:1)
2)FP(1:N)
3)PIN+”←”+PW
4)RF+PW
FP/RF
Fingerprint or RF is verified
1)PIN+FP(1:1)
2)FP(1:N)
3)RF
PW/RF
Fingerprint or RF is verified
1) RF
2) PIN+”←”+PW
147
TFT Fingerprint V6.3
FP/PW/RF
Fingerprint or RF or Password is verified
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+PW
4) RF
FP&PIN
Fingerprint and PIN are verified
1)PIN+”←”+FP(1:1)
2) RF+ PIN+”←”+FP(1:1)
FP&PW
Fingerprint and PIN are verified
1) FP(1:N)+PW
2) PIN+FP(1:1)+PW
3) RF+PW + FP(1:1)
FP&RF
Fingerprint and RF are verified
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+FP(1:1)+RF
PW&RF
Password and RF are verified
1) RF+PW
2) PIN+”←”+PW+RF
FP&PW&RF
Fingerprint, Password and RF are verified
1) FP(1:N)+PW+RF
2) PIN+FP(1:1)+PW+RF
3) RF+ PW+ FP(1:1)
FP&PIN&PW
Fingerprint, PIN and Password are verified
148
TFT Fingerprint V6.3
1) PIN+”←”+PW+FP(1:1)
2) RF+ PIN+”←”+PW+FP(1:1)
FP & PIN /RF
Fingerprint and PIN, or fingerprint and RF are verified
1) FP+ PIN
2) FP +RF
3) PIN+FP(1:1) + PIN
4) PIN+FP(1:1) +RF
When enroll user, register card, but only register a fingerprint or only
register your password, the verification process as following table:
149
TFT Fingerprint V6.3
Type
Description
Password registered
FP
only
verification
fingerprint
1
)
PIN+FP(1:1
verification)
2)FP (1: N verification)
3)RF+FP(1:1)
PIN
only
verification
1)PIN+“←”
Password
Wrong password
RF
1) PIN+“←”+PW
2)RF+PW
only RF Card verification
1)RF
FP/PW
1)RF
password or fingerprint
verification
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+“←”+ FP(1:1)
4) RF+FP(1:1)
FP/RF
Unable to pass
number verification only
1)PIN+“←”
PW
fingerprint registration
fingerprint
verification
or
1) PIN+FP(1:1)
2) FP(1:N)
150
1) PIN+“←”+PW
2) RF+PW
RF
1)RF
TFT Fingerprint V6.3
3) RF
PW/RF
password
verification
or
RF
1) RF
2) PIN+“←”+PW
FP/PW/RF
1) PIN+”←”+PW
2) RF
fingerprint or password or
RF verification
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+“←”+ FP(1:1)
4) RF+FP
FP&PIN
FP&PW
FP&RF
1) PIN+”←”+PW
2) RF
number and fingerprint
verification
1) PIN+“←”+FP(1:1)
2) RF +“←”+FP(1:1)
fingerprint and password
verification
Unable to pass
Unable to pass
Unable to pass
fingerprint
verification
and
R
Unable to pass
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)+RF
PW&RF
password
verification
and
Unable to pass
RF
1) RF+PW
2) PIN+“←”+PW+RF
151
TFT Fingerprint V6.3
FP&PW&RF
fingerprint, password and
RF verification
Unable to pass
FP&PIN&PW
Unable to pass
fingerprint, number and
password
Unable to pass
FP&RF/PIN
Unable to pass
Fingerprint
and
RF
verification
or
fingerprinting
and
numbers verification
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+“←”+FP(1:1)
Unable to pass
Note: 1) When a user register card number (or similar to ID card) and
also enrolled a fingerprint in the equipment, above table the RF can be
verified by only punch card, then do not need to place fingerprints.
2) Combination of authentication methods, the use of fingerprints,
password and Mifare cards are registered is recommended,
otherwise may be unable to validation.
Example: A user only register the fingerprints, and methods of
verification for the PW, then the user can not be verified .
152
TFT Fingerprint V6.3
Appendix 9 Remote server Solution★
Because of the limit of standalone machine capacity and speed,
there is impossibility to add a large mount of fingerprints (for
example, up to ten thousands of fingerprints). Even if the capacity
can be expanded, the standalone machine speed can’t be assured;
the speed is much slower than PC’s. Based on above reasons,
Standalone is an incapable for those large systems which have large
fingerprint capacity and high matching efficiency, so a fingerprint
solution, i.e. remote server solution, is put forward, which can deal
with large capacity and high efficiency.
Concept
Taking standalone machine as fingerprint scanner, its standalone
identification function is reserves. With identification and
verification, and then stores matching results in the background DB
and displays identification results on the fingerprint machine LCD,
to complete the task of identification process. Which Identification
algorithm adopts intellectual property algorithm Biokey , the
common PCs can act as remote server, the remote sever solution
has lower requirement of entire identification system and improve
algorithm efficiency, thus assure of feasibility and convenience of
solution.
Solution Purpose: large capacity of fingerprint identification,
enhanced enterprise internal management, intelligent management,
In/Out control for personnel.
153
TFT Fingerprint V6.3
Architecture of Remote server
The basic mode adopts C/S mode, please see the following figure
Prim-Server
PC
Central database
and Server
Sec-Serv
A5
PC_server
A5
PC_server
Server
Terminal
A5
154
TFT Fingerprint V6.3
Appendix 10 WIFI★
Wi-Fi (short for "wireless fidelity") is a term for certain types of
wireless local area network (WLAN) that use specifications in the
802.11 family. The term Wi-Fi was created by an organization
called the Wi-Fi Alliance, which oversees tests that certify product
interoperability. A product that passes the alliance tests is given the
label "Wi-Fi certified" (a registered trademark).
Originally, Wi-Fi certification was applicable only to products
using the 802.11b standard. Today, Wi-Fi can apply to products
that use any 802.11 standard. The 802.11 specifications are part of
an evolving set of wireless network standards known as the 802.11
family. The particular specification under which a Wi-Fi network
operates is called the "flavor" of the network. Wi-Fi has gained
acceptance in many businesses, agencies, schools, and homes as an
alternative to a wired LAN. Many airports, hotels, and fast-food
facilities offer public access to Wi-Fi networks. These locations are
known as hot spots. Many charge a daily or hourly rate for access,
but some are free. An interconnected area of hot spots and network
access points is known as a hot zone.
Unless adequately protected, a Wi-Fi network can be susceptible to
access by unauthorized users who use the access as a free Internet
connection. The activity of locating and exploiting
security-exposed wireless LANs is called war driving. An
identifying iconography, called war chalking, has evolved. Any
155
TFT Fingerprint V6.3
entity that has a wireless LAN should use security safeguards such
as the Wired Equivalent Privacy (WEP) encryption standard, the
more recent Wi-Fi Protected Access (WPA), Internet Protocol
Security (IPsec), or a virtual private network (VPN).
Its main features are: high speed, high reliability, in the opening of
region, communications distance of up to 305 meters, in a closed
region, communication distance is 76 m to 122 m, convenient ,
Network costs are lower than the existing wired Ethernet.
We fingerprint machine has also realized the WIFI function. WIFI
modules can be built-in fingerprint machine , can be an external
module WIFI to achieve through WIFI wireless data transmission.
For detail , please see 4.3 Wireless Settings
156
TFT Fingerprint V6.3
Appendix 11 GPRS★
General Packet Radio Services (GPRS) is a packet-based wireless
communication service that promises data rates from 56 up to 114
Kbps and continuous connection to the Internet for mobile phone
and computer users. The higher data rates allow users to take part
in video conferences and interact with multimedia Web sites and
similar applications using mobile handheld devices as well as
notebook computers. GPRS is based on Global System for Mobile
(GSM) communication and complements existing services such
circuit-switched cellular phone connections and the Short Message
Service (SMS).
We fingerprint machine has also realized the GPRS function.
GPRS modules can be built-in fingerprint machine , also can be an
external GPRS module to achieve the GPRS systems for data
transfer.
How to operate GPRS fingerprint machine, please see 4.5 dail-up
settings.
157
TFT Fingerprint V6.3
Appendix 12 Print function★
[Explain]
this function is designed for a serial port printer only, the parallel printer
is unavailable. the content that attempt to print output via RS232 , after
each user is verified the result will be sended out through serial port. If
fingerprint machine connect with the printer the result can be printed
directly, can also use the Super Terminal to wiew the output content.
Fingerprint machine connect
with printer
Fingerprint machine printer
2 TXD <--------> 3 RXD
3 RXD <--------> 2 TXD
5 GND <--------> 7 FG
[Instructions]
Fingerprint machine
printer
2 TXD
<-----> 3 RXD
3 RXD <-----> 2 TXD
5 GND <----->
7 FG
Note: the baud rate of fingerprint machine and printer is same
with.
158
TFT Fingerprint V6.3
[Connection Schematic diagram]
1)There is a 9PIN serial Port on the fingerprint machine
2)The fingerprint machine with connection terminal
159
TFT Fingerprint V6.3
Appendix 13 Web Server
★
At the first time use the WebServer, should be configure the setting,
enter menu -> communications settings fingerprints IP address, such as
set up the IP address of the fingerprint machine to 192.168.1.225; type
the http://192.168.1.225 in IE address bar
The default the system user name of super administrator: administrator;
Password: 123456.
1) Enter view records
160
TFT Fingerprint V6.3
① Left-click option "View In-Out records" interface;
② to select staff you want to view in the list;
③ designate the time scope for view.
2) Export In –Out records: Save these logs to local disk.
① left click "Export logs" option;
161
TFT Fingerprint V6.3
② choose staff you want save his records in the list; ③ select file
format to save.
④ click "start the download" and save the file to the local disk.
3) synchronization equipment time
① left click "synch equipment time" option on the interface;
162
TFT Fingerprint V6.3
② select the adjustment method
Auto: Time of computer and equipment will be automatically
synchronized.
Manual adjustments: manually set the time of the equipment and
defined time synchronization.
③ local equipment date
Choose automatic adjustment, this machine‘s date and time is the
computer date.
Choice of manual adjustments can manually enter the time.
④ click the "modified" button to change the time of equipment
4) communication parameter
① left click "communication parameters" option on interface
② enter the communications parameters
• Ethernet:
(1) Through the hub: with cable (for connecting Net cards and hubs)
connect machines to the network.
163
TFT Fingerprint V6.3
(2) Directly connection: Use the cross-cable (direct connect the two
Ethernet endpoint) to connect machines and PC .
IP Address: The default IP is 192.168.1.201, you can make changes
based on the actual situation;
Subnet Mask: The default subnet mask 255.255.255.0, you can make
changes based on the actual situation;
Gateway Address: default gateway address 0.0.0.0, you can make
changes based on the actual situation;
• RS232: the use of RS232 serial port.
Baud rate: the communications and computer communications rate,
high-speed communications faster, the proposed use of RS232
communications 115200,57600 the baud rate.
RS232/RS485: whether or not to use RS232 communications, select
On the RS232 apply .
• RS485 way
Baud rate: the communications and computer communications rate,
low-speed
communication
stability,
the
proposed
RS485
communications the baud rate 9600,38400.
RS232/RS485: whether or not to use RS485 communications, select
On the way to use RS485.
③ click "Save settings" button to write into the parameters of
communications equipment.
164
TFT Fingerprint V6.3
RoHS Compliance
•The standard of environmental protection of these products in this
statement refers to safety deadline under the conditions of provisions
using the product no leakage of toxic or hazardous substances harmful
to.
• The standard of environmental protection products by the deadline
does not include the batteries or be easy to wear and tear of the regular
replacement parts. The deadline for the use of environmentally friendly
batteries is five years.
Table of hazardous substances' name and concentration
Component
Name
Hazardous substances’ name
(Pb
)
( Hg
)
(Cd)
(Cr6+
)
( PBB
)
(PBDE)
resistors
×
○
○
○
○
○
SMD
capacitor
×
○
○
○
○
○
SMD
inductors
×
○
○
○
○
○
SMD diode
×
○
○
○
○
○
PCB
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adopter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the
homogeneous materials for this part is below the limit requirement in
SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least
165
TFT Fingerprint V6.3
one of the homogeneous materials used for this part is above the limit
requirement in SJ/T11363-2006.
Note: 80% component of this product are made from non-toxic or
hazardous substance, Applications of hazardous substances in this
device are required to achieve its intended uses, due to lack of
reasonably (economically or technically) available substitutes. Indicates
that the concentration of the hazardous
166
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement