User Manual - Automated Environmental Systems

SS Pool & Spa Pump
20
21
22
1
2
41
42
43
44
45
23
3
21
49
24
25
4
26
30
11
5
12
27
31
1 5 16
50
46
28
47
48
29
32
58
6
7
40
36
33
8
17
13 14
34
37
38
39
54
5 1 52
35
18 19
55 56
57
53
9 10
Key NO.
Description
Qty
Par t No.
1
Lid Assembly
1
031101
2
Seal O'ring
1
3
Handle
4
Key NO.
Description
Qty
Par t No.
Nut for irdome
1
031111
Waterproof plug for cable
1
030131
1
030303
Screw for irdome
4
030132
Basket
1
031103
Washer
4
030222
5
Pump Body
1
031105
32
Washer for irdome
1
030225
6
O'ring
2
030236
33
Waterproof O'ring for motor shaft
1
031102
Union head (imperial standard,1.5",48mm)
2
02012101
34
Skidproof piece
1
031110
35
Skidproof washer
1
031116
Motor 0.5HP
1
030422
Motor 0.75HP
1
030423
Motor 1.0HP & 1.2HP
1
030424
7
30
31
030128
Union head (metric standard 1.5",50mm)
2
02012102
8
90° Nut
2
020140
9
Drain cover
2
031104
10
Washer
1
031112
11
O'ring for Diffuser
1
031107
37
Fan for moter
1
030230
12
Diffuser
1
031108
38
Elastic protective ring (Type B)
1
031133
Lid for Impeller
1
031106
Cover for motor
1
030226
Impeller Φ99*8.7
Screw for cover
Waterproof plug for cable
4
1
1
1
1
030144
Cable 3*0.75mm 2*2.1m
Waterproof plug wire 3*0.75mm2*2.1m
13
36
1
0304212
39
40
Impeller Φ99*10.6
1
0304213
41
Impeller Φ99*13.3
1
0304214
Impeller Φ100*17.2
Nut for irdome
030415
030128
1
0311061
42
1
1
0304063
43
Screw for irdome
O'ring for flange
4
030410
44
Irdome
15
Round screw
1
1
030408
031114
Cable placement piece
O'ring
4
030129
031115
45
1
16
Screw for cable placement piece
2
17
Shaft Seal 1/2”
4
030233
46
Belt
1
030133
030137
18
Flange
1
031109
47
Waterproof Washer for the cover of irdome
1
030416
19
Screw with washer
1
031117
Earth copper screw
1
Cable 3*1.5mm *2.5m
8
030141
Washer
1
Waterproof plug wire 3*1.5mm2*2.5m
1
030315
Washer
1
21
Screw
1
030221
Earth cable
Lid for irdome
6
1
22
030210
Safety pressing cable nut
Washer for the cover of irdome
3
23
1
030224
Capacitance 5UF/450V/50/60HZ
1
030411
24
Cable placement piece
1
030129
Capacitance 6UF/450V/50/60HZ
Safety pressing cable nut
1
030412
1
030136
Capacitance 8UF/450V
51
Waterproof O'ring for motor shaft
3
1
030211
1
52
Skidproof washer
1
0311161
030212
53
Skidproof piece
1
031110
Motor 0.2HP
1
030418
Motor 0.33HP
1
030419
55
Fan for moter
1
030420
1
Copper nut Φ14*14-M8
14
2
20
25
26
Capacitance 14 UF/450V
Capacitance 20UF/450V
1
031113
030213
48
49
50
030409
030135
030413
27
Belt
1
28
Irdome
1
030209
Earth copper screw
1
030160
Washer
1
030161
56
Elastic protective ring (Type B)
Washer
1
030162
1
030417
1
030135
57
58
Cover for motor
Earth cable
Screw for cover
4
030144
29
030137
54
INSTALLATION
Only qualified, licensed personnel should install pump and wiring.
IMPORTANT ELECTRICAL
Electrical Contractors Please Note: All 220 volt 50 Hz pumps must be wired to the
main power supply through an approved and correctly rated contactor.
Pump Mount Must:
Be solid Level Rigid Vibration Free.
Allow use of short, direct suction pipe. (To reduce friction losses & don’t install the pump at
more than 3M geometrical height from water level)
Allow for gate valves in suction and discharge piping.
Have adequate floor drainage to prevent flooding.
Be protected from excess moisture.
All adequate access for servicing pump and piping.
NOTICE:
Pump suction and discharge connections have moulded in thread stops, DO NOT try to screw
pipe in beyond these stops.
EMPU06052612
OPERATION
!
!
!
!
Hazardous suction.
Can trap hair or
body part, causing
severe injury or
death.
Do not block
suction.
NEVER run pump dry! Running pump dry may damage seals,
causing leakage and flooding! Fill pump with water before
starting motor.
Before removing lid:
STOP PUMP before proceeding.
CLOSE GATE VALVES in suction and discharge pipes.
RELEASE ALL PRESSURE from pump and piping system.
NEVER tighten or loosen screws while pump is operation.
Do not block pump suction! To do so with body may cause severe or fatal
injury. Children using pool must ALWAYS have close adult
Supervision!
Priming Pump:
Release all air from filter and piping system: see filter owner
manual.
In a flooded suction system (water source higher than pump),
pump will prime itself when suction and discharge valves are
opened.
If pump is not in a flooded suction system, unscrew and remove
trap cover; fill trap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only.
Pump should prime now. Priming time will depend on vertical
length of suction lift and horizontal length of suction piping.
Routine Maintenance
The only routine maintenance needed is inspection/cleaning of trap basket. Debris or trash that
collects in basket, will choke off water flow through the pump. Follow instructions below to clean trap:
1.Stop pump, close gate valve in suction and discharge, and release all pressure from system before
proceeding.
2.Unscrew trap lid (turn counterclockwise).
3.Remove strainer basket and clean. Be sure all holes in basket are clear,flush basket with water and
replace in trap with large opening at pipe connection port (between ribs provided). If basket is
replaced backwards cover will not fit on trap body.
4.Clean and inspect lid Ring; reinstall on trap cover.
5.Clean Ring groove on trap body and Replace lid. To help keep lid from sticking, tighten hand tight
only.
6.Prime pump (see priming instructions above)
SERVICE & REPAIR PARTS
Refer all service to your local agent or dealer as his knowledge of your equipment makes
him the vest qualified source of information. Order all repair parts through your dealer. Give
the following information when ordering repair parts:
1. Unit nameplate data or serial number on label.
2. Description of part.
TROUBLE SHOOTING
MOTOR DOES NOT START
1. Disconnect switch or circuit breaker in
off position
2. Fuses blown or thermal overload open
3. Locked motor shaft
4. Motor windings burned out
5. Defective starting switch inside singl
phase motor
6. Disconnected or defective wiring
7. Low voltage
PUMP DOES NOT REACH FULL SPEED
1. Low voltage
2. Pump connected for wrong voltage
MOTOR OVERHEATS (protector trips)
1. Low voltage
2. Motor windings connected for wrong
voltage on dual voltage model
3. Inadequate ventilation
PUMP DELIVERS NO WATER
1. Pump is not primed
2. Closed valve in suction or discharge
line
3. Leakage or air into suction system
4. Impeller clogged
LEAKAGE OF WATER AT SHAFT
1. Shaft seal requires replacement
LOW PUMP CAPACITY
1. Valve in suction or discharge line partly
closed
2. Suction or discharge line partly plugged
3. Suction or discharge line too small
4. Plugged basket in skimmer or hair and
lint strainer
5. Dirty filter
6. Impeller clogged
HIGH PUMP PRESSURE
1. Discharge valve or inlet fittings closed
too much
2. Return lines too small
3. Dirty filters
NOISY PUMP AND MOTOR
1. Plugged basket in skimmer or hair in lint
strainer
2. Worn motor bearings
3. Valve in suction line partly closed
4. Suction line partly plugged
5. Vacuum hose plugged or too small
6. Pump not supported properly
AIR BUBBLES AT INLET FITTINGS
1. Leakage of air into suction line at
connections or valve stem
2. Cover gasket of hair and lint strainer
needs cleaning
3. Low water level in pool
NOTE: If the recommendations in the trouble shooting portion of this manual do not
solve your particular problem(s), please contact your local dealer for service.
Download PDF