SMA series Touch Monitor
User Manual
Please read this manual very carefully before using your device
and store in a safe place for future reference.
Model No.:
Take down the model number for reference.
Serial No.:___________________
1
Table of Contents
Important Notes
2
Accessories
4
Features
5
Control Panel
6
Interface
7
Remote Control
8
Instructions
9
Installing the Wall Mount
13
Installing and Using the Touch Screen Software
14
Specifications - PC
18
Specifications - Touch Screen
18
Specifications - Monitor
19
Toxic & Hazardous Materials
20
2
Important Notes
For your safety please read this manual very carefully before use and keep it properly for any
reference. We will take no responsibilities for any accidents resulting from violation of the safety and
usage guidelines in this Manual.
Explanation of Signs
The signs used in this Manual and which are affixed on the product are listed below. Please read the
Manual carefully and make sure you fully understand these signs.
This sign warns about the risk of serious personal injury or even death
due to incorrect operation.
This sign warns about the risk of personal injury or property damage
due to incorrect operation.
This sign warns of high voltage. Only professional staff is allowed to
maintain and replace the parts to avoid fire or shock hazards.











To avoid electric shock, do not open the back cover. There are no parts inside that users can fix.
Turn to a professional if you encounter any problems.
Do not insert any metal parts into the openings of the monitor, to avoid electric shock.
Do not install this monitor on an unstable surface, such as a loose shelf, a sloping floor or an
insecure wall. Turn off the power and contact the local dealer if the monitor falls to the ground
or gets damaged.
Keep the monitor away from rain and do not install in places near water (e.g. bathtub, basin,
wet floor, etc.). If the monitor accidentally gets wet, disconnect the power, unplug from the
power source, and contact your local dealer.
The openings on the back cover are designed for ventilation and allow heat to escape. Do not
block these openings and use the monitor only in adequately ventilated places.
Make sure the power outlet is in good condition before plugging the monitor, to avoid electric
shock or damage.
Unplug the power cable and TV tuner during bad weather and thunderstorms to avoid
damage.
Clean the monitor with a soft cloth. Never use harsh chemicals to clean your monitor.
Do not use any object or material that can scratch the surface or cause friction or indentations.
Do not affix stickers, labels or gummed paper to the touch screen. Keep it clean.
Avoid dropping the remote control.
Make sure you have enough space for installation
Allow the necessary distance between the monitor and other objects (e.g. the wall) to ensure adequate
ventilation. Product failure may result from heat build-up caused by poor ventilation.
3
 Physical appearance may vary slightly depending
on the model.
Moving the monitor
Two persons or more are required to handle
the monitor.
Hold the top and bottom frame firmly to move
the monitor.
4
Accessories
 These images are intended for reference only. Refer to actual product.
Features









The super speed infrared touch screen allows for smooth writing, stable performance, prompt response
and HID. It can support multi-touch (2-point and 4-point) with possibility to zoom in/out, drag and
rotate the object selected.
It uses high quality FULL HD LED panel with features of high brightness, high contrast ratio, color
optimization function, bit by bit image, dynamic and static screen enhancing function.
Optional PC box leaves no external cables.
Super slim, esthetically pleasing frame, just 8 cm.
Very low power consumption in standby mode.
Rounded corners ensure safety
Additional USB and HDMI inputs in the front.
Power ON-OFF by remote control.
Compatible with Windows, Linux, and other Operating Systems.
5
Control Panel
 PC power indicator lights up in models with built-in PC
6
Interface
7
Remote Control
8
Instructions
Turning on the monitor
When the power cable is connected, the TV indicator on the front control panel is red. Press the POWER
button on the front control panel or the remote control, the TV indicator in red will flash for 5 seconds, then
the TV and built-in PC (optional) will be turned on. The monitor indicator will be blue and the built-in PC
indicator will be green.
To turn on the monitor alone, press POWER button to turn on the PC and monitor as above, then switch off
the PC via the operating system.
Turning off the monitor
The monitor and built-in PC (optional) can be turned off with one button as follows:
Initial State

State after pressing POWER (single button solution)
PC is OFF, monitor is ON
Monitor will be turned off
Both PC and TV are On
PC will be turned off first, then the monitor.
If you need to turn both monitor and in-built PC OFF immediately, press POWER button for 3 seconds.
Turning off the backlight
Press SLEEP button on the front control panel to turn off the monitor backlight. The monitor indicator will
change from blue to red and the other parts of the monitor will still be working.
Press SLEEP button again to turn on the backlight.
Distance Sensing
There is a distance sensor built into the front control panel. The monitor will
turn off automatically if something is blocking the sensor within a 10 cm
distance for 8-10 seconds.
9
Select Signal Source
Via the buttons on the control panel
① Press SOURCE button on front control panel: the sources will be listed as
shown on the right.
② Press P+ or P- to select signal source.
③ Press SOURCE button on front control panel to confirm the signal source
selected.
Via remote control
① Press SOURCE BUTTON on remote control; the sources will be listed as
shown on the right.
② Press ▲ or ▼ to select signal source
③ Press SOURCE button on remote control to confirm the signal source
selected.
Auto Switch Source
Both the built-in PC (optional) and HDMI port on the front control panel are in
HDMI 1 source as default setting. When you connect an external PC to the
HDMI port on the front control panel, the source will be automatically
switched to HDMI 1.
When the built-in PC (optional) and the HDMI port on the front control panel
are connected at the same time, you must unplug the HDMI connection on the front control panel and
external PC in order to have the signal source from the built-in PC.
Installing and Removing the built-in PC (optional)
The built-in PC box allows for easy installation and
maintenance.
The PC is built into the back of the monitor. Loosen
the screws and grasp the PC to move it out smoothly.

Do not remove the PC if it is functioning properly. If it
is necessary to remove it, disconnect the power from
the monitor first.

Installation is the same for OPS and Mini ATX PCs.
10
Connecting To External PC
If necessary, you can connect your monitor to
an external PC for interactive operation.
① Connecting to interface on front control
panel
This monitor has a port on the front control
panel for easy operation.
Connect the HDMI cable for video and audio
signals; connect the USB cable for touch
screen functionality.

HDMI and USB cables may or may not be
included in your supply. Check with your
dealer in advance.
② Connecting to the ports on the back of
your monitor.
Connect the VGA and audio cables to
transmit the signal from the external PC to
the monitor. Then connect USB cable for
touch screen functionality.
Connection by HDMI can replace the VGA
and Audio cables.

11
Connecting Other External Equipment to the monitor
You can connect other external equipment like a PC or a DVD to the monitor via VGA, HDMI, YPBPR, AV, USB,
etc. (see fig.)

The figure is intended for reference only

You may have to prepare some connecting cables.
Connecting to a projector
You can connect the monitor to a projector as
explained below:
Connect VGA and HDMI output from PC.
Connect VGA output from extended interface.
12
Installing the Wall Mount
13
Installing and Using the Touch Screen Software
(Ⅰ)Setup
1.
Load the attached disk into the CD-ROM
2.
Double-click to run “TouchDevSetup.exe” in the
disc.
3.
Complete installation accordingly.
Click “Finish” and run touch screen management
application “Fitouch.exe”. The installation will be
completed when
appears on the desktop’s
lower right-hand corner.
Blue indicates the
equipment has been connected.
Gray indicates the equipment has not been
connected or a failed connection
(Ⅱ)Basic Function
1.
Run TouchDev.exe
By default, the software will automatically execute; the icon can
be found on the desktop’s lower right-hand corner.
If you accidentally close the software, click “start”->“program”,
find and select “TouchDev”,
then run it. By default, the
shortcut of “TouchDev” is on the desktop. Double click it.
2.
Main Menu
Click the “TouchDev” icon. The main menu will pop up as
shown in the figure. Functions include:
Language: Lets you select the relevant language for the
interface.
Calibration: Lets you calibrate the screen so that the touch and
actual location on the screen match.
Options: Shows basic information regarding the touch screen;
allocates relevant parameters for real requirements.
About: Shows other information regarding TouchDev.
14
Exit: Closes TouchDev.
3.
Calibration:
Standard calibration:
As shown in the figure on the left, there are “custom” and
“advanced” options for calibration. If neither one of the two
options is selected, calibration will be standard. Standard
calibration is suitable when connecting only one electronic
white board.
“Calibrate mode” includes “TouchPanel” (touch screen) and
“TouchBoard” (electronic white board). “Touchboard” supports
positioning of non-rectangle screen, and “TouchPanel” only
supports positioning of rectangle screen. When adopting a
projector, choose “TouchPanel” mode.
Under “calibrate position” you will find two positions “1” and
“2”: in the first the display icon is close to the 4 angles of the
screen; in the second, the display icon is close to the center of
the screen. (Note: the first is recommended.)
4.
Screen calibration:
After selection, click “calibration”. The interface as shown in the
figure on the left will appear. Use a touch pen or your finger to
touch the center of icon“
”. (During positioning, the touch
pen must be vertical to the screen surface, and pen point
coincide with the center of icon “
”.)
The positioning icon will move to the 4 angles of the screen
upon touch. For “Touchboard” mode, the icon will also appear
in the center of the screen.
Custom calibration:
Custom mode, when selected, supports two kinds of
positioning.
1) In “custom” mode two electronic white boards must be
connected at the same time. (Custom mode is not supported in
the case of one electronic whiteboard.).
15
2) Matching between two parts of the screen: When the
screen is split in two, with separate performance on both parts
at the same time and both parts requiring touch functionality,
carry out positioning on both sides, first on the left, then on the
right.
5.
Options:
Information:
The “Basic” box shows information regarding the current
screen. If there is more than one touch screen device, a
number will be assigned to each one and their specific
information displayed.
The “features” box shows updated information regarding the
touch screen, “√” is supported, and “×” is not supported.
Upgrading method: (related authorized documents are needed
before upgrading.)
Click “×” in “features” to show the upgrading box:
Click “upgrade” to search for the authorized documents for
upgrading.
6.
Configuration:
For “service parameters” configuration, we suggest using the
default value, unless there is a specific requirement.
Description of parameters: right button enabling: select “Yes”
to use right button; select “No”, the right button is disabled.
Delayed time length: Sets the time length for right button
enabling.
Fault-tolerant space: Errors while pressing on the screen with
the hand; errors within a range are permitted.
Sleek coefficient: set sampling points, to ensure data points
sent to the system are smooth and to avoid excessive vibration
of scribing line.
16
(Ⅲ)Basic Operation
General
The following operations may be performed on the screen:
operation
Click------object on the screen
Double click------click the same object twice quickly on the same screen
Drag------press the object and drag it
Right key------press the object and remain for 2-3 second
17
PC Specifications
Item
Mini ATX PC
OPS PC
Main Board
Mini ITX,Intel H61 chipset
Intel QM67 chipset
Intel1155 Pentium、I3、I5、I7. The model
Intel I3、I5、I7. The model no. is subject to
no. is subject to the real products
the real products.
Graphics
Integrated Intel(R)HD Graphics
Integrated Intel(R)HD Graphics
RAM
DDRIII 1333 /2G/4G
SO-DIMM DDRIII 1333 /2G/4G
CPU
HDD
SATA 2.5" 500G
WIFI
Support IEEE802.11b/g/n,150/300Mbps, Max area 100m,security encryption (optional)
Bluetooth
Support V3.0+EDR,Max 3Mbps, reliable distance 10m (optional)
Touch Screen Specifications
Touch technology
Non-contact Infrared Sensing Technology
Sensing Object
Non-transparent object (like pen, finger etc.)
Size of Sensing Object
≥ Ø5mm
Multi-touch
2-point,4-point
Single Touch:click:8ms writing:3ms
Response Time
Multi-Touch:click:8ms writing:8ms
Cursor Speed
Up to 300dots/second
Touch Resolution
4096×4096
Positioning Accuracy
≤±2mm
Glass
4mm tempered Mohs 7 anti-explosive, transparency : >92%
Lifespan
No limit
18
Monitor Specifications
Size
55 inch
Speakers
8W+8W
TV
PAL /SECAM,BG/DK/I
Resolution
View Angle
1920*1080
65 inch
70 inch
1920*1080
1920*1080
178°
Image:JPEG、BMP、PNG
Multi-Media
Audio:WMA、MP3、M4A、AAC
Formats
Video:MPEG1、MPEG2、MPEG4、H264、RM、RMVB、MOV、MJPEG、VC1、DivX、
FLV
Working
0℃ to 40℃
Temperature
Working
10% to 90%, No condensation
Humidity
Storing
-20℃ to 60℃
Temperature


Machine Size
1296.5x792.5x81mm
1550x944x96.5mm
1626x979x102mm
Packing Size
1425x970x210mm
1650x1085x210mm
1755x1135x210mm
Net Weight
40kg
55kg
60kg
The design and specifications may be changed without any prior notice.
Please refer to the labels on the product and packing for power and power consumption information.
19
Toxic and Hazardous Materials or Elements
Toxic and Hazardous Material
Item
Hexavalent
Lead
Mercury
(PH)
(HG)
Chromium
Polybrominated
Polybrominated
Chrome
(CD)
Diphenyl Ethers
Biphenyl (PBB)
(Cr(VI))
(PBDE)
PCB
Shell
LCD/LED
panel
Speakers
Accessories
○: indicates that content of such material in the parts is below the limit of SJ/T11363-2006.
×: indicates that the content of such material in the parts is above the limit of SJ/T11363-2006.
The substance marked with × falls into the category that cannot be removed or replaced by the technology
from a scientific point of view, (EU RoHS Directive 2002/95/EC); not in the listed materials of restricted content
under SJ/T11363-2006 of PR China (except Taiwan, Hong Kong and Macao).
Download PDF