HEX100HDVGA
HDMI
LINK
VGA
In
Audio
LINK
HDMI in
IR RX IR TX
RS232
HEX100HDVGA – RX/TX
User Manual
Input
Select
HDBT Out
Power
DC12V
HEX100HDVGA – RX/TX USER MANUAL
Thank you for purchasing
this product.
For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this
manual for future reference.
Surge protection device
recommended
This product contains sensitive electrical components that may be damaged
by electrical spikes, surges, electric
shock, lightning strikes, etc. Use of
surge protection systems is highly
recommended in order to protect and
extend the life of your equipment.
02
Contents
Introduction
03
Features
03
Panel Descriptions
04
RS232 Control
06
Specifications
07
Package Contents
07
Maintenance
07
www.blustream.co.uk
HEX100HDVGA – RX/TX USER MANUAL
Introduction
The HEX100HDVGA is a HDMI and VGA/Audio switcher extender solution with HDMI audio
de-embedder. Utilizing a single Cat5e/6 cable the HEX100HDVGA can distribute HDMI, VGA/
Audio, bi-directional IR &RS232 control. The HEX100HDVGA has auto video signal-sensing
switching which activates the last video signal connected to the units or optionally both
the transmitter (TX) and receiver (RX) units offer manual and RS232 switching.
The HEX100HDVGA is designed as a simple low-cost solution in school and business
applications.
FEATURES:
• Auto signal sensing switches between HDMI and VGA+
Audio (Analogue 3.5mm stereo audio) to HDMI output with
Analogue Left/Right audio and Coaxial digital outputs. Units
will switch when new signal detected.
• Manual switching of HDMI and VGA/Audio input signal on
both Transmitter and Receiver units using manual or RS232
control.
• HDMI input audio de-embedded onto Analogue Left/Right
audio and Coaxial digital outputs (Supports PCM audio
only).
• Dolby TrueHD and DTS-HD master audio pass through HDMI
output
• Support for all popular VGA resolutions: 640x480@60/75Hz,
720x400@70Hz, 800x600@60/75Hz, 1024x768@60/75Hz,
1152x864@75Hz, 1280x720@60Hz, 1280x768@60/75Hz,
1280x800@60/75Hz, 1280x960@60Hz, 1280x1024@60/75Hz,
1360x768@60Hz, 1366x768@60Hz, 1400x1050@60Hz,
1440x900@60Hz, 1600x1200@60Hz, 1680x1050@60Hz,
1920x1080@60Hz, 1920x1200@60Hz
• Bi-directional IR and RS232
• HDMI v1.4 and HDCP compliant, support 1080p@60Hz, 3D
and 4K.
• RS232 supports bypass via HDBaseT link (default), input
switching control or firmware update.
• Support 1080P@60Hz or VESA:1920x1200 @60Hz up to
100m, 4K up to 60m
• POH (Power over HDBT) supported, only one power supply
needed at either transmitter or receiver side.
NOTE: The POH function is designed for powering compatible transmitter or receiver units of Blustream only.
Do not connect any part of this equipment to power over Ethernet devices. Damage may result.
contact support@blustream.co.uk / support@blustream.com.au
03
HEX100HDVGA – RX/TX USER MANUAL
HEX100HDVGA - Transmitter
Front Panel
Back Panel
HEX100HDVGA
HDMI
LINK
VGA
1
In
LINK
Audio
HDMI in
2
3
IR RX IR TX
4
RS232
6
5
1VGA input
2 Analogue Left/Right audio input - 3.5mm Stereo Jack
3 HDMI input – Connect to HDMI source device
4 IR Rx port – Transmits IR to HEX100HDVGA-Rx
(Tx IR port). Connect Blustream IR sensor or control
processor to send IR commands to a display
5 IR Tx port – Connect a 5V Blustream IR emitter.
Used to control source devices from display end.
Input
Select
7
Power
HDBT Out
DC12V
9
10
8
6RS232 port – Bi-directional RS232 to and from the
HEX100HDVGA-RX
7 Input select button – switch between HDMI and VGA/
Audio input.
8 Input status indicator – Red=VGA/Audio,Blue=HDMI
9 HDBaseT out – RJ45 connector, connect to HDBaseT
input on HEX100HDVGA-RX
q Power port – Use supplied 12v / 2amp DC adaptor
(HEX100HDVGA kit can be powered at either
transmitter or receiver units)
RS232 Mode DIP Switch Settings
12
0
1
RS232
Mode
11
DIP Position 1
DIP Position 2
Mode
0
0
RS232 Pass Through HDBaseT
(default)
0
1
HDBaseT Firmware Update
1
0
Master Firmware Update
1
1
Switch between inputs via RS232
& RS232 pass through HDBaseT
wRS232 management DIP switches – See table on right
for settings
04
www.blustream.co.uk
HEX100HDVGA – RX/TX USER MANUAL
HEX100HDVGA - Receiver
Front Panel
Back Panel
HEX100HDVGA
LINK
RS232
1
Input
Select
2
3
HDMI
LINK
Power
HDBT In
DC12V
4
5
Coaxial
L
Audio Out
R
7
8
6
HDMI Out
9
1RS232 port – Bi-directional RS232 to and from the
HEX100HDVGA-TX
6Coaxial digital output
2Input select button – switch between HDMI and VGA/
Audio input.
8Analogue Right audio RCA output
3Input status light – Red=VGA/Audio, Blue=HDMI
4HDBaseT in – RJ45 connector, connect to HDBaseT
output on HEX100HDVGA-TX
5Power port – Use supplied 12v / 2amp DC adaptor
(HEX100HDVGA kit can be powered at either
transmitter or receiver units)
IR RX IR TX
10
11
7Analogue Left audio RCA output
9HDMI output – Connect to HDMI display device
qIR Rx port – Connect to Blustream 5v IR sensor. Used to control
IR controlled source devices at HEX100HDVGA-Tx end
wIR Tx port – Connect to Blustream 5v IR emitter. Used to
control display device from control processor or IR sensor
located at the source end
RS232 Mode DIP Switch Settings
12
0
1
RS232
Mode
12
DIP Position 1
DIP Position 2
Mode
0
0
RS232 Pass Through HDBaseT
(default)
0
1
HDBaseT Firmware Update
1
0
Master Firmware Update
1
1
Switch between inputs via RS232
& RS232 pass through HDBaseT
eRS232 management DIP switches – See table on right
for settings
contact support@blustream.co.uk / support@blustream.com.au
05
HEX100HDVGA – RX/TX USER MANUAL
RS232 Control
RS232 switching codes for VGA and HDMI inputs
No.
Codes
Description
1
vgaselect
Switching to VGA input
2
hdmiselect
Switching to HDMI input
3
getselect
Get status of currently selected input, return message will be HDMI port or VGA port
4
ensigdet
Enable signal detect (Auto switching)
5
dissigdet
Disable signal detect (Auto switching)
6
resetdef
Restore factory settings
RS232 Pin assignment
Blustream
Remote Control Console
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
06
www.blustream.co.uk
HEX100HDVGA – RX/TX USER MANUAL
Specifications
HEX100HDVGA-TX
Audio Input Connectors: 1x Analogue Left/Right 3.5mm stereo jack
Video Input Connectors: 1x HDMI Type A & 1x VGA
Video Output Connectors: 1x HDBaseT RJ45 connector
IR Input Port: 1x 3.5mm stereo jack
IR Output Port: 1x 3.5mm mono jack
RS232 Serial Port: 1x DB9 female
Casing Dimensions (W x H x D): 124mm x 113mm x 29mm
Dimensions including connections (W x H x D): 133mm x 113mm x 29mm
HEX100HDVGA-RX
Audio Output Connectors: 2x Analogue RCA Left/Right & Coaxial digital
Video Input Connectors: 1x HDBaseT RJ45 connector
Video Output Connectors: 1x HDMI Type A
IR Input Port: 1x 3.5mm stereo jack
IR Output Port: 1x 3.5mm mono jack
RS232 Serial Port: 1x DB9 female
Casing Dimensions (W x H x D): 124mm x 113mm x 29mm
Dimensions including connections (W x H x D): 135mm x 113mm x 29mm
Shipping Weight (Kit): 1.1kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature : -4°F to 140°F (-20°C to 60°C)
Power Supply: 12V/2A DC
contact support@blustream.co.uk / support@blustream.com.au
07
HEX100HDVGA – RX/TX USER MANUAL
Package Contents:
Maintenance:
• 1 x HEX100HDVGA Transmitter
Clean this unit with a soft, dry cloth. Never use alcohol,
paint thinner or benzene to clean this unit.
• 1x HEX100HDVGA Receiver
• 1 x 12V/2A DC power supply
• 1 x Blustream 5v IR sensor
• 1x Blustream 5v IR emitter
• 1x Mounting kit
• 1x Manual
08
www.blustream.co.uk
HEX100HDVGA – RX/TX USER MANUAL
Example Schematic
HEX100HDVGA
VGA
Coaxial Digital
Speaker Cable
Analogue Audio
RS232
HDMI
Cat5/6 Cable
Control Processor
VGA
In
RS232
Audio
HDMI
LINK
Input
Select
HDMI in
HDBT Out
Power
HEX100HDVGA
DC12V
IR RX IR TX
LINK
Coaxial
L
Audio Out
RS232
R
HDMI
LINK
Input
Select
HDMI Out
HDBT In
Power
HEX100HDVGA
DC12V
IR RX IR TX
LINK
09
contact support@blustream.co.uk / support@blustream.com.au
www.blustream.co.uk
www.blustream.com.au
Download PDF