ACE PLUS CORP.
EX-G048B
2-port DVI Splitter
Datasheet
Page 1 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Safety and Notice
The EX-G048B 2-port DVI Splitter has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like
all electronic equipments, EX-G048B should be used with care. Please read and follow
the safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this manual.
Provide proper ventilation and air circulation and do not use near water.
Keep objects that might damage the device and assure that the placement of this
unit is on a stable surface.
Use only the power adapter and power cords and connection cables designed for
this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Page 2 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Introduction
The EX-G048B receives and reconstructs (equalizing & reclocking) a DVI signal
and distributes it to two identical outputs. It can be perfectly cascaded with one
another in order to obtain more DVI outputs (at least 6 tiers). Each output can be
turned on/off individually through an IR remote control (optional). It will also process
(read & store) the EDID information sent through the Data Display Channel (DDC).
Features
Connects a DVI video source to 2 DVI compatible displays
Perfectly as a repeater by regenerating the DVI signal
Stackable, 6 devices stacked can support up to 13 outputs
IR remote control allows switching outputs (optional)
Reads and remembers the EDID of displays
Can be modified EQ with two modes
Extends greater than 14m/45ft of input/output DVI cable
Page 3 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Package Contents
1x EX-G048B
1x 5V DC power adapter
1x User Manual
1x Remote Control (optional)
Technical Specifications
Input connector: 1 x DVI-I
Output connector: 2 x DVI-I
Maximum Resolution: 1600 x 1200
LEDs:1 x Green (ID), 1 x Red (Power)
DIP switch: 2
Power Supply: 5V DC
Dimensions: 120mm/4.7”x 88mm/3.5”x 25mm/1” (Lx Wx H)
Weight: 300g/10.6oz
Page 4 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Panel Descriptions
Front View
1.
2.
Connect first DVI display here.
Connect second DVI display here.
Rear Panel
3.
4.
5.
6.
7.
8.
5V DC
Connect a device equipped with DVI output (such as a PC) here.
Rotary switch- Assign an ID (0-7) for the device while cascading. For
example, you can set rotary switch at 1 for the first EX-G048B and 2 for the
second EX-G048B. Please ignore the rotary switch when only single
EX-G048B exists.
Green LED- lights when the EX-G048B is selected.
Red LED- lights when power on.
Infrared Receiver
Page 5 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Button View
Mode
1 On Open EQ. Less noise but more power consumption.
Off Close EQ.
2 On Writing default EDID.
*Set the DIP switch at on and plug in power cord. The green LED will light after the writing
process is completed.
Off Record EDID of the connected display via DVI-OUT1
*Plug in DVI cable first from the display and then plug in power cord. The recording process will
be initiated and the green LED lights. The green LED will turn of after the reading process is
completed.
Warning!! Don’t plug in DVI source while the EX-G048B is writing default
EDID or recording EDID from displays. This will cause damage to the
EDID in the flesh memory.
If you cannot boot your computer from the connected EX-G048B due to
the damaged EDID in the EX-G048B, please proceed the “Writing default
EDID” and then “Recording EDID of the connected display”. This will
enforce the EX-G048B to write the EDID from display.
Page 6 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Hardware Installation
We suggest you connect the monitor with the lowest resolution support to the
DVI-OUT 1. (E.g. Suppose monitor A might support a maximum resolution of 1920 x
1200, monitor B supports a maximum resolution of 1280 x 1024 and monitor C
supports a maximum resolution of 1024 x 768, please connect monitor C to
DVI-OUT 1).
Unless you would like to use the default universal EDID, please set DIP switch 2 at
off position, which allows the EX-G048B to read the first connected monitor’s EDID.
1. Connect a monitor, a projector or other displays with DVI inputs by a
male-to-male DVI cable to DVI-OUT 1.
2. Plug DVI Y-cable into EX-G048B
3. Connect the second display to the DVI-OUT 2.
4. Plug 5V DC power adapter into power jack.
5. Connect a PC or other devices with DVI outputs to EX-G048B DVI-IN.
DVI-OUT2
DVI cable
DVI-IN
DVI cable
Page 7 of 8
DVI-OUT1
DVI cable
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
ACE PLUS CORP.
Limited Warranty
The SELLER warrants the EX-G048B 2-port DVI Splitter to be free from defects in
the material and workmanship for 1 year from the date of purchase from the SELLER or
an authorized dealer. Should this product fail to be in good working order within 1 year
warranty period, The SELLER, at its option, repair or replace the unit, provided that the
unit has not been subjected to accident, disaster, abuse or any unauthorized
modifications including static discharge and power surges.
Unit that fails under conditions other than those covered will be repaired at the
current price of parts and labor in effect at the time of repair. Such repairs are warranted
for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail,
customers agree to insure the unit or assume the risk of loss or damage in transit. Under
no circumstances will a unit be accepted without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without
limitations, any other implied warranty or fitness or merchantability for any particular
purpose, all of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan
are responsible for shipping charges to and from the SELLER. Cables are limited to a 30
day warranty and cable must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be
accurate. However, The SELLER assumes no responsibility for any inaccuracies that
may be contained in this manual. The SELLER will NOT be liable for direct, indirect,
incidental, special, or consequential damages resulting from any defect or omission in
this manual, even if advised of the possibility of such damages. Also, the technical
information contained herein regarding the EX-G048B features and specifications is
subject to change without further notice.
Page 8 of 8
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: +886-2-2912-4201
FAX: +886-2-2912-3164
Website: www.ace-plus.com
Download PDF