PJD6235/PJD6245/PJD6543w DLP Projector

PJD6235/PJD6245/PJD6543w
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://www.
YLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQER[LQWKH
upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las
instrucciones en este manual”
Model No. VS14931/VS14933/VS14934
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
y
Reorient or relocate the receiving antenna.
y
Increase the separation between the equipment and receiver.
y
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
y
&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS
Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKH
party responsible for compliance could void your authority to operate the equipment.
For Canada
y
This Class B digital apparatus complies with Canadian ICES-003.
y
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent
or discarded batteries or accumulators as unsorted municipal waste, but use the return
and collection systems available.
If the batteries, accumulators and button cells included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal
content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than
0.004% Lead.
i
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
GHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade and the third prong are provided for your safety. If
WKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOWDQHOHFWULFLDQIRUUHSODFHPHQWRIWKH
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience
UHFHSWDFOHVDQGWKHSRLQWZKHUHWKH\H[LWIURPWKHXQLW%HVXUHWKDWWKHSRZHURXWOHWLV
located near the unit so that it is easily accessible.
2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\WKH
manufacturer, or sold with the unit. When a cart is used, use caution when moving
the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKHXQLWKDV
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid
LVVSLOOHGRQWRRUREMHFWVIDOOLQWRWKHXQLWLIWKHXQLWLVH[SRVHGWRUDLQRUPRLVWXUHRULIWKH
unit does not operate normally or has been dropped.
ii
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC
of the European Parliament and the Council on restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply
ZLWKWKHPD[LPXPFRQFHQWUDWLRQYDOXHVLVVXHGE\WKH(XURSHDQ7HFKQLFDO$GDSWDWLRQ
Committee (TAC) as shown below:
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb)
0.1%
< 0.1%
< 0.01%
Substance
Cadmium (Cd)
0.01%
+H[DYDOHQW&KURPLXP&U6+)
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
&HUWDLQFRPSRQHQWVRISURGXFWVDVVWDWHGDERYHDUHH[HPSWHGXQGHUWKH$QQH[RIWKH5R+6
Directives as noted below:
([DPSOHVRIH[HPSWHGFRPSRQHQWVDUH
1. /HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQGHOHFtronic ceramic parts (e.g. piezoelectronic devices).
2. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or
more lead).
3. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by
weight.
iii
Copyright Information
Copyright © ViewSonic® Corporation, 2012. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks
of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and
DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing
this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
FKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFXPHQWPD\FKDQJHZLWKRXW
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic®
Wizard CD-ROM also provides an opportunity for you to print the registration form, which you
PD\PDLORUID[WR9LHZ6RQLF
For Your Records
Product Name:
PJD6235/PJD6245/PJD6543w
ViewSonic DLP Projector
Model Number:
VS14931/VS14933/VS14934
Document Number:
PJD6235/PJD6245/PJD6543w_UG_ENG Rev. 1A 12-04-12
Serial Number:
_______________________________________________
Purchase Date:
_______________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the environment.
Please use care and dispose of in accordance with local, state or federal laws.
ViewSonic respects the environment and is committed to working and living green. Thank you
for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
7DLZDQKWWSUHF\FOHHSDJRYWZUHF\FOHLQGH[DVS[
iv
Table of contents
Controlling the projector through a LAN
environment ....................................... 39
Using the projector in standby mode. 45
Shutting down the projector .............. 46
Menu operation.................................. 47
Important safety
instructions .......................2
Introduction......................4
Projector features ................................. 4
Shipping contents................................. 5
Projector exterior view......................... 6
Controls and functions ......................... 7
Maintenance ...................57
Care of the projector .......................... 57
Lamp information .............................. 58
Positioning your
projector..........................12
Troubleshooting .............64
Specifications ..................65
Choosing a location............................ 12
Projection dimensions ........................ 13
Projector specifications...................... 65
Dimensions ........................................ 67
Ceiling mount installation ................. 67
Timing chart ...................................... 68
Connection ......................15
Connecting a computer or monitor .... 16
Connecting Video source devices ...... 17
Copyright information...71
Operation ........................20
Appendix.........................72
Starting up the projector..................... 20
Using the menus................................. 21
Utilizing the password function ......... 22
Switching input signal........................ 25
Adjusting the projected image ........... 26
Magnifying and searching for details. 27
Selecting the aspect ratio ................... 28
Optimizing the image......................... 31
Setting the presentation timer ............ 35
Hiding the image................................ 36
Locking control keys.......................... 36
Freezing the image ............................. 36
Operating in a high altitude
environment ....................................... 36
Using the CEC function ..................... 37
Using the 3D functions ...................... 37
IR control table .................................. 72
RJ45 response table ........................... 74
RS232 command table....................... 74
1
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Please read this manual before you operate your projector. Save it for future
reference.
Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
Refer servicing to qualified service personnel.
Always open the lens shutter or remove the lens cap when the projector lamp is
on.
In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
2
13.
Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14.
Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15.
16.
17.
18.
Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19.
20.
When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommends that you also purchase a separate Kensington lock compatible security
cable and attach it securely to both the Kensington lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the projector
should its attachment to the mounting bracket become loose.
3
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Dynamic PC and Dynamic Movie functions adjusting the power consumption of the
lamp according to the brightness of the image being projected
DynamicEco Timer function decreasing the power consumption of the lamp by up to
30% when no input signal can be detected for a set period of time.
Presentation timer for better control of time during presentations
LAN Settings allowing management of projector status from a remote computer
Supports 3D display
Color Management allowing color adjustments to your liking
Less than 0.5W power consumption when power saving mode is turned on
Screen Color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Color and Reference modes providing choices for different projection purposes
Selectable quick power off function
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color management control for data/video display
Ability to display 1.07 billion colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Component HDTV compatibility (YPbPr)
HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/
OFF operation between the projector and a CEC-compatible device connected to the
HDMI input of the projector
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
4
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector
Power Cord
VGA Cable
Multi-language user
manual DVD
Quick Start Guide
Remote Control & Batteries
Optional accessories
1.
2.
3.
Replacement lamp
Soft carry case
VGA-Component adapter
5
Projector exterior view
1.
Front/upper side
1
6
2
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
3
4
5
7
Rear/lower side
8
9
10 11
12
13.
13 14 15 16 17
19
18
14.
15.
16.
17.
18.
19.
External control panel
(See "Projector" on page 7 for
details.)
Lamp cover
Vent (heated air exhaust)
Front IR remote sensor
Adjuster foot
Focus and Zoom rings
Projection lens
RS-232 control port
RJ45 LAN input port
Type B USB port
HDMI port
RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-2
RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-1
RGB signal output socket
S-Video input socket
Video input socket
Audio signal input socket
Audio signal output socket
Kensington anti-theft lock slot
AC power cord inlet
Warning
•
THIS APPARATUS MUST BE EARTHED.
•
When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
6
Controls and functions
Projector
1
2
3
4
5
3
6
1.
2.
3.
4.
5.
Focus ring
Adjusts the focus of the projected image.
Zoom ring
Adjusts the size of the image.
Keystone/Arrow keys ( / Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection.
Left/Blank
Hides the screen picture.
POWER indicator light
Lights up or flashes when the projector is
under operation.
MENU
EXIT
8.
9.
10.
I
I
6.
7.
POWER
Toggles the projector between standby
mode and on.
SOURCE
Displays the source selection bar.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
7
11.
12.
7
8
9
10
11
12
Right
Activates panel key lock.
When the On-Screen Display (OSD)
menu is activated, the #3, #4, and #8 keys
are used as directional arrows to select the
desired menu items and to make
adjustments.
LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
AUTO
Automatically determines the best picture
timings for the displayed image.
TEMPerature indicator light
Lights up red if the projector's
temperature becomes too high.
MODE/ENTER
Selects an available picture setup mode.
Enacts the selected On-Screen Display
(OSD) menu item.
Remote control
1
18
2
3
4
5
19
6
4
8
7
20
9
21
10
11
12
13
15
16
17
22
14
23
24
25
To use the remote mouse control keys
(Page Up, Page Down, , and ), see
"Using the remote mouse control" on
page 10 for details.
6.
7.
1.
2.
3.
4.
5.
I
I
POWER
Toggles the projector between standby
mode and on.
Source selection keys (VGA/Video)
Selects an input source for display.
VGA
Selects D-Sub / Comp. 1 or D-Sub /
Comp. 2 source for display.
Video
Selects Video (HDMI/Video/SVideo) source for display.
Source
Displays the source selection bar.
Keystone keys ( / )
Manually corrects distorted images
resulting from an angled projection.
/ / /
Selects the desired menu items and
makes adjustments.
8.
Enter
Enacts the selected On-Screen Display
(OSD) menu item.
My Button
Allows user to define a short cut key
on the remote control, and the function
item is selected in OSD menu.
Menu
Turns on the On-Screen Display
(OSD) menu.
9.
Performs the same function as the left
mouse button when the mouse mode is
activated.
10.
11.
Performs the same function as the
right mouse button when the mouse
mode is activated.
Mouse
Switches between the normal and
mouse modes.
Page Up, Page Down, , : active
after pressing Mouse. An icon appears
on the screen to indicate the activation
of the mouse mode.
8
12.
Magnify
Displays the zoom bar that magnifies or
reduces the projected picture size.
13.
Lock
Activates or deactivates panel key lock.
Freeze
Freezes the projected image.
Pattern
Displays embedded test pattern.
Blank
Hides the screen picture.
DynamicEco™
Decreases the power consumption of the
lamp by up to 30%.
14.
15.
16.
17.
19.
20.
21.
22.
23.
It takes some time to initiate this
function. Make sure the projector has
been turned on for more than 4 minutes.
If the projector is resumed by using the
Smart Restart feature, this function can
be executed immediately.
18.
Color Mode
Selects an available picture setup mode.
Exit
Goes back to previous OSD menu, exits
and saves menu settings.
PgUp (Page Up)/PgDn (Page Down)
Operates your display software program
(on a connected PC) which responds to
page up/down commands (like Microsoft
PowerPoint) when the mouse mode is
activated.
Volume keys (+, -)
Magnifies or reduces the volume level.
Auto Sync
Automatically determines the best picture
timings for the displayed image.
24.
25.
Toggles the projector audio between on
and off.
Aspect
Selects the display aspect ratio.
Timer
Displays the presentation timer settings
menu.
Remote control code
The projector can be assigned to two different remote control codes, A or B. When several
adjacent projectors are in operation at the same time, switching the remote control codes
can prevent interference from other remote controls. Set the remote control code for the
projector first before changing that for the remote control.
To switch the code for the projector, select A or B in the SYSTEM SETTING:
ADVANCED > Remote Control Code menu.
To switch the code for the remote control, press PgUp and PgDn buttons on the remote
control together for 5 seconds or more. The initial code is set to A.
If different codes are set on the projector and remote control, there will be no response from
the remote control. When that happens, switch the code for the remote control again.
9
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1.
2.
3.
4.
Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer" on
page 16 for details.
Set the input signal to D-Sub / Comp. 1, D-Sub / Comp. 2.
Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse mode.
Perform the desired mouse controls on your remote control.
•
To move the cursor on the screen, press
/
/
/
.
•
To left-click, press
•
To right-click, press
•
To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
•
To return to the normal mode, press Mouse again or other keys except for the
mouse related multi-function keys.
.
.
Remote control effective range
The Infra-Red (IR) remote control is located on the front
of the projector. The remote control must be held at an
angle within 30 degrees perpendicular to the projector's
IR remote control sensor to function correctly. The
distance between the remote control and the sensor should
not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote
control and the IR sensor on the projector that might
obstruct the infra-red beam.
10
Appr
ox. 3
0°
Replacing the remote control batteries
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it in the direction of the arrow as illustrated. The
cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position.
Stop when it clicks into place.
•
Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
•
Replace only with the same or equivalent type recommended by the battery manufacturer.
•
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
•
Never throw the batteries into a fire. There may be danger of an explosion.
•
If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
11
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2.
Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETTING:
BASIC > Projector Position menu after you turn
the projector on.
3.
Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETTING:
BASIC > Projector Position menu after you turn
the projector on.
4.
Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETTING:
BASIC > Projector Position menu after you turn
the projector on.
12
Projection dimensions
Refer to "Dimensions" on page 67 for the center of lens dimensions of this projector before
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface
and a support structure
PJD6235/PJD6245
•
4:3 image on a 4:3 screen
(a)
(b)
(e)
(a)
(f)
(d)
(c)
(c)
(d)
(f)
(e)
•
(b)
16:9 image on a 4:3 screen
(a)
(b)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
4:3 image on a 4:3 Screen
(a) Screen
Size
[inch (m)]
(b) Projection
distance [m (inch)]
min.
max.
16:9 image on a 4:3 Screen
(c) Image (d) Vertical (b) Projection distance (c) Image (d) Vertical
[m (inch)]
height
offset
offset
height
[cm (inch)] [cm (inch)]
[cm (inch)] [cm (inch)]
min.
max.
30
(0.8) 1.1 (45) 1.2 (49)
46
(18)
5
(1.8) 1.1
(45)
1.2
(49
34
(14) 10.3 (4.1)
40
(1.0) 1.5 (59) 1.7 (65)
61
(24)
6
(2.4) 1.5
(59)
1.7
(65)
46
(18) 13.7 (5.4)
50
(1.3) 1.9 (74) 2.1 (82)
76
(30)
8
(3.0) 1.9
(74)
2.1
(82)
57
(23) 17.1 (6.8)
60
(1.5) 2.3 (89) 2.5 (98)
91
(36)
9
(3.6) 2.3
(89)
2.5
(98)
69
(27) 20.6 (8.1)
70
(1.8) 2.6 (104) 2.9 (114) 107 (42)
11
(4.2) 2.6 (104) 2.9 (114)
80
(32) 24.0 (9.5)
80
(2.0) 3.0 (119) 3.3 (131) 122 (48)
12
(4.8) 3.0 (119) 3.3 (131)
91
(36) 27.4 (10.8)
90
(2.3) 3.4 (134) 3.7 (147) 137 (54)
14
(5.4) 3.4 (134) 3.7 (147) 103
(41) 30.9 (12.2)
100 (2.5) 3.8 (149) 4.2 (163) 152 (60)
15
(6.0) 3.8 (149) 4.2 (163) 114
(45) 34.3 (13.5)
120 (3.0) 4.5 (178) 5.0 (196) 183 (72)
18
(7.2) 4.5 (178) 5.0 (196) 137
(54) 41.1 (16.2)
150 (3.8) 5.7 (223) 6.2 (245) 229 (90)
23
(9.0) 5.7 (223) 6.2 (245) 171
(68) 51.4 (20.3)
200 (5.1) 7.5 (297) 8.3 (327) 305 (120) 30 (12.0) 7.5 (297) 8.3 (327) 229
(90) 68.6 (27.0)
250 (6.4) 9.4 (371) 10.4 (409) 381 (150) 38 (15.0) 9.4 (371) 10.4 (409) 286 (113) 85.7 (33.8)
300 (7.6) 11.3 (446) 12.5 (490) 457 (180) 46 (18.0) 11.3 (446) 12.5 (490) 343 (135) 102.9 (40.5)
13
PJD6543w
•
16:10 image on a 16:10 screen
(a)
(b)
(e)
(a)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
•
16:10 image on a 4:3 screen
(a)
(b)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
16:10 image on a 16:10 Screen
16:10 image on a 4:3 Screen
(a) Screen
(b) Projection distance (c) Image (d) Vertical (b) Projection distance (c) Image (d) Vertical
Size
[m (inch)]
[m (inch)]
height
offset
height
offset
[inch (m)]
[cm (inch)] [cm (inch)]
[cm (inch)] [cm (inch)]
min.
max.
min.
max.
30
(0.8) 0.97 (38)
1.06 (42)
40
(16)
0
(0.0) 0.91 (36) 1.00
(40)
38
(15)
3.8
(1.5)
40
(1.0) 1.29 (51)
1.42 (56)
54
(21)
0
(0.0) 1.22 (48) 1.34
(53)
51
(20)
5.1
(2.0)
50
(1.3) 1.61 (64)
1.77 (70)
67
(26)
0
(0.0) 1.52 (60) 1.67
(66)
64
(25)
6.4
(2.5)
60
(1.5) 1.94 (76)
2.13 (84)
81
(32)
0
(0.0) 1.83 (72) 2.01
(79)
76
(30)
7.6
(3.0)
70
(1.8) 2.26 (89)
2.48 (98)
94
(37)
0
(0.0) 2.13 (84) 2.34
(92)
89
(35)
8.9
(3.5)
80
(2.0) 2.58 (102) 2.84 (112) 108
(42)
0
(0.0) 2.43 (96) 2.68 (105)
102
(40) 10.2 (4.0)
90
(2.3) 2.90 (114) 3.19 (126) 121
(48)
0
(0.0) 2.74 (108) 3.01 (119)
114
(45) 11.4 (4.5)
100 (2.5) 3.23 (127) 3.55 (140) 135
(53)
0
(0.0) 3.04 (120) 3.35 (132)
127
(50) 12.7 (5.0)
120 (3.0) 3.87 (152) 4.26 (168) 162
(64)
0
(0.0) 3.65 (144) 4.02 (158)
152
(60) 15.2 (6.0)
150 (3.8) 4.84 (191) 5.32 (210) 202
(79)
0
(0.0) 4.56 (180) 5.02 (198)
191
(75) 19.1 (7.5)
200 (5.1) 6.45 (254) 7.10 (279) 269 (106) 0
(0.0) 6.09 (240) 6.70 (264)
254 (100) 25.4 (10.0)
250 (6.4) 8.06 (318) 8.87 (349) 337 (132) 0
(0.0) 7.61 (300) 8.37 (329)
318 (125) 31.8 (12.5)
300 (7.6) 9.68 (381) 10.65 (419) 404 (159) 0
(0.0) 9.13 (359) 10.04 (395)
381 (150) 38.1 (15.0)
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
14
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
•
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
•
The connection illustrations below are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
•
For detailed connection methods, see pages 16-19.
Notebook or desktop computer
A/V device
Monitor
1
(VGA)
1.
2.
3.
4.
2
or
3
1
7
8
(DVI)
VGA cable
VGA to DVI-A cable
USB cable
Component Video to VGA (D-Sub)
adapter cable
15
5.
6.
7.
8.
4
7
5
S-Video cable
Video cable
Audio cable
HDMI cable
6
Speakers 7
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1.
2.
3.
Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
If you wish to use the remote paging function, take a USB cable and connect the
larger end to the USB port of the computer, and smaller end to the MINI USB socket
on the projector. See "Using the remote mouse control" on page 10 for details.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1.
2.
3.
Connect the projector to a computer as described in "Connecting a computer" on page
16.
Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
Connect the other end of the cable to the MONITOR OUT socket on the projector.
•
The MONITOR OUT output only works when COMPUTER IN 1 connection is made to the
projector.
•
To use this connection method when the projector is in standby mode, turn on the Active
VGA Out function under the SYSTEM SETTING: BASIC > Standby Settings menu.
16
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• HDMI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with a HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 18 for how to connect the projector to a HDMI
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 18 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 19 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 19 for how to connect the
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theater or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.
17
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
To connect the projector to an HDMI device:
1.
2.
Take an HDMI cable and connect one end to the HDMI output port of the video
device.
Connect the other end of the cable to the HDMI input port on the projector.
•
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color
space to YUV. See "Changing HDMI input settings" on page 25 for details.
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 17 for details.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
2.
Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red
to red.
Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub
type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the
projector.
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 17 for details.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
VGA-Component adapter
(ViewSonic P/N: CB-00008906)
18
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
2.
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 17 for details.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 17 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
2.
Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
Connect the other end of the Video cable to the VIDEO socket on the projector.
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 17 for details.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 17 for details.
19
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted).
RS-2 32
LAN
2.
MINI USB
I
I
Press
POWER on the projector or remote
control to start the projector. The POWER
indicator light stays blue when the projector is
on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
•
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 60 seconds before energizing the lamp.
•
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
3.
4.
5.
If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
Switch all of the connected equipment on.
The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 25 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 68 for details.
20
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
Main menu icon
Screen Color
Aspect Ratio
Keystone
Position
Phase
H. Size
Zoom
Highlight
Sub-menu
Off
Auto
Status
ENTER
16
0
3D Settings
Color Management
Current input
signal
Analog RGB
MENU Exit
Go to the
previous page
or to exit.
To use the OSD menus, please set them to your familiar language first.
1.
Press MENU/EXIT on the projector or
Menu on the remote control to turn the
OSD menu on.
Screen Color
Aspect Ratio
Keystone
Position
Phase
H. Size
Zoom
3D Settings
Color Management
Analog RGB
2.
to highlight
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Splash Screen
Message
LAN Control Settings
Standby Settings
CEC
Analog RGB
16
0
MENU Exit
English
Front Table
Disable
Disable
Off
ViewSonic
On
Press
Language and press / to
select a preferred language.
Off
Auto
Use / to highlight the SYSTEM
SETTING: BASIC menu.
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Splash Screen
Message
LAN Control Settings
Standby Settings
CEC
Analog RGB
3.
4.
English
Front Table
Disable
Disable
Off
ViewSonic
On
Off
MENU Exit
Press MENU/EXIT twice* on
the projector or Exit on the
remote control to leave and
save the settings.
*The first press leads you back
to the main menu and the
second press closes the OSD
menu.
Off
MENU Exit
: DISPLAY
: SYSTEM SETTING: BASIC
: PICTURE
: SYSTEM SETTING: ADVANCED
: SOURCE
: INFORMATION
21
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 21.
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
1.
Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Security
Settings menu. Press MODE/ENTER on the projector or Enter on the remote
control. The Security Settings page is displayed.
2.
3.
Highlight Power On Lock and select On by pressing
As pictured to the right, the four arrow keys
4.
( , , , ) respectively represent 4 digits
(1, 2, 3, 4). According to the password you desire
to set, press the arrow keys to enter six digits for
the password.
Confirm the new password by re-entering the
MENU Back
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
5.
/
.
INPUT PASSWORD
•
Once a password has been set, the projector cannot be used unless the correct password
is entered every time the projector is started.
•
The digits being input will be displayed as asterisks on-screen. Write your selected
password down here in this user manual in advance or right after the password is entered
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
Password Error
the projector. If you enter the wrong password, the
Please try again.
password error message as pictured to the right is
displayed lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not record the password in this user
manual, and you absolutely do not remember it, you can use the password recall procedure.
See "Entering the password recall procedure" on page 23 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
22
Entering the password recall procedure
1.
2.
3.
4.
5.
Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Security
Settings > Change Password menu.
Press MODE/ENTER on the projector or Enter on the remote control. The message
'INPUT CURRENT PASSWORD' is displayed.
Press and hold AUTO on the projector or Auto
RECALL PASSWORD
Sync on the remote control for 3 seconds. The
Please write down the recall code,
and contact ViewSonic
projector will display a coded number on the
Customer Center.
screen.
Recall code:
Write down the number and turn off your
0212
projector.
MENU Exit
Seek help from the local service center to decode
the number. You may be required to provide
proof of purchase documentation to verify that you are an authorized user of the
projector.
Changing the password
1.
2.
3.
4.
5.
6.
7.
Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Security
Settings > Change Password menu.
Press MODE/ENTER on the projector or Enter on the remote control. The message
'INPUT CURRENT PASSWORD' is displayed.
Enter the old password.
•
If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT CURRENT PASSWORD' is
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
Enter a new password.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
23
Disabling the password function
To disable password protection, go back to the SYSTEM SETTING: ADVANCED >
Security Settings > Power On Lock menu after opening the OSD menu system. Select Off
by pressing / . The message 'INPUT PASSWORD' is displayed. Enter the current
password.
•
If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT PASSWORD' is displayed for your
retry. You can press MENU/EXIT on the projector or Exit on the remote
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
24
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by
pressing one of the source selection keys on the
remote control, or cycle through the available input
signals.
D-Sub / Comp. 1
1.
Press SOURCE on the projector or remote
control. A source selection bar is displayed.
D-Sub / Comp. 2
2.
Press
/
until your desired signal is
selected and press MODE/ENTER on the
projector or Enter on the remote control.
Once detected, the selected source information
will be displayed on the screen for seconds. If
there are multiple devices connected to the
projector, repeat steps 1-2 to search for another
signal.
HDMI
Video
S-Video
•
The brightness level of the projected image will change accordingly when you switch
between different input signals. Data (graphic) "PC" presentations using mostly static
images are generally brighter than "Video" using mostly moving images (movies).
•
The input signal type effects the options available for the Color Mode. See "Selecting a
picture mode" on page 31 for details.
•
Please see "Projector specifications" on page 65 for the native display resolution of this
projector. For best display picture results, you should select and use an input signal
which outputs at this resolution. Any other resolutions will be scaled by the projector
depending upon the 'aspect ratio' setting, which may cause some image distortion or loss
of picture clarity. See "Selecting the aspect ratio" on page 28 for details.
Changing HDMI input settings
In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray
player) via the projector’s HDMI input and the projected picture displays wrong colors,
please change the color space to an appropriate one that fits the color space setting of the
output device.
To do this:
1.
Open the OSD menu and go to the SOURCE menu.
2.
Press
to highlight HDMI Format and press / to select a suitable color space
according to the color space setting of the output device connected.
3.
•
RGB: Sets the color space as RGB.
•
YUV: Sets the color space as YUV.
•
Auto: Sets the projector to detect the color space setting of input signal
automatically.
Press
to highlight HDMI Range and press / to select a suitable HDMI color
range according to the color range setting of the output device connected.
•
Enhanced: Sets the HDMI color range as 0 - 255.
25
•
Normal: Sets the HDMI color range as 15 - 235.
•
This function is only available when the HDMI input port is in use.
•
Refer to the documentation of the device for information on the color space setting.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with an adjuster foot. It
changes the image height and vertical projection
angle. Screw the adjuster foot to fine tune the
angle until the image is positioned where you
want it.
If the projector is not placed on a flat surface or
the screen and the projector are not perpendicular
to each other, the projected image becomes
trapezoidal. To correct this situation, see
"Correcting keystone" on page 27 for details.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on the
projector or Auto Sync on the remote control. Within 3 seconds, the built-in Intelligent
Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the
best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
•
The screen will be blank while AUTO is functioning.
•
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
1.
Adjust the projected image to the size 2.
that you need using the zoom ring.
26
If necessary, sharpen the image by
rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
• Using the remote control
Press / on the projector or remote control to
display the Keystone correction page. Press
to
correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the image.
Press /
Press
/
• Using the OSD menu
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
2.
3.
until the DISPLAY menu is highlighted.
Press
to highlight Keystone and press MODE/ENTER on the projector or Enter
on the remote control. The Keystone correction page is displayed.
Press
to correct keystoning at the top of the image or press
to correct
keystoning at the bottom of the image.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
• Using the remote control
1.
Press Magnify on the remote control to display the Zoom bar.
2.
3.
4.
Press
repeatedly to magnify the picture to a desired size.
To navigate the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch to the paning mode and press the directional arrows
( , , , ) to navigate the picture.
To reduce size of the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch back to the zoom in/out functionality, and press AUTO/Auto
Sync to restore the picture to its original size. You can also press
it is restored to the original size.
repeatedly until
• Using the OSD menu
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
2.
3.
until the DISPLAY menu is highlighted.
Press
to highlight Zoom and press MODE/ENTER on the projector or Enter on
the remote control. The Zoom bar is displayed.
Repeat steps 2-4 in the section of Using the remote control above.
•
The picture can only be navigated after the picture is magnified. You can further magnify
the picture while searching for details.
•
Images can only be magnified up to 120% when the aspect ratio is Wide or Anamorphic.
27
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
• Using the remote control
1.
Press Aspect to show the current setting.
2.
Press Aspect repeatedly to select an aspect ratio to suit the format of the video signal
and your display requirements.
• Using the OSD menu
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the DISPLAY menu is highlighted.
2.
Press
3.
Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
to highlight Aspect Ratio.
28
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.
Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the
image's aspect ratio.
16:10 picture
15:9 picture
2.
3.
4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration.
4:3 picture
16:9: Scales an image so that it is displayed in
the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
16:9 picture
4.
16:10 (PJD6543w only): Scales an image so
that it is displayed in the center of the screen
with a 16:10 aspect ratio. This is most suitable
for images which are already in a 16:10 aspect,
as it displays them without aspect alteration
16:10 picture
5.
Wide (PJD6543w only): Scales a 4:3 aspect
image vertically and horizontally in a non-linear
manner so that it fills the screen with a 16:9
aspect ratio.
4:3 picture
29
6.
Anamorphic (PJD6235/PJD6245 only): Scales
a 16:9 aspect image vertically and horizontally
in a non-linear manner so that it fills the screen
with a 4:3 aspect ratio.
16:9 picture
30
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
•
Press MODE/ENTER on the projector or Color Mode on the remote control
repeatedly until your desired mode is selected.
•
Go to the PICTURE > Color Mode menu and press
/
to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1.
Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2.
PC mode: Is designed for presentations under daylight environment to match PC and
notebook coloring.
3.
ViewMatch mode: Switches between high brightness performance and accurate color
performance.
4.
Movie mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5.
Dynamic PC mode: Is designed for presentations under daylight environment to
match PC and notebook coloring. In addition, the projector will optimize the image
quality using the dynamic PC function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6.
Dynamic Movie mode: Is appropriate for playing colorful movies, video clips from
digital cameras or DVs through the PC input for best viewing in a blackened (little
light) environment. In addition, the projector will optimize the image quality using the
dynamic Movie function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
7.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr) / HDMI
1.
Brightest mode: Optimized for daylight viewing, with living room level ambient
brightness.
2.
Gaming mode: Suitable for all types of entertainment media, including gaming and
movies.
3.
ViewMatch mode: Switches between high brightness performance and accurate color
performance.
31
4.
5.
Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best
viewed in a blackened (little light) home cinema or lounge room environment. In
addition, the projector will optimize the image quality using the dynamic Movie
function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting
point and customize the settings.
1.
2.
Press MENU/EXIT on the projector or Menu on the remote control to open the OnScreen Display (OSD) menu.
Go to the PICTURE > Color Mode menu.
3.
Press
4.
Press
/
to select User 1 or User 2.
to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode
sub-menu item.
5.
Press
6.
Press
to select a sub-menu item to be changed and adjust the value with / .
See Fine-tuning the image quality in user modes below for details.
When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
The confirmation message 'Setting Saved' is displayed.
7.
8.
/
to select a picture mode that is closest to your need.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press / to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. You can make adjustments to these functions
based on your needs.
When you are done making adjustments, remember to go to the PICTURE > Save Settings
menu and press MODE/ENTER to save your settings.
32
Adjusting Brightness
Highlight the PICTURE > Brightness menu and press
/
.
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
+30
+50
+70
0
+30
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press
/
.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
-30
Adjusting Color
Highlight the PICTURE > Color menu and press
/
.
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press
/
.
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press
/
.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press
/
.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press
/
.
The options available for color temperature* settings vary according to the signal type
selected.
1.
2.
3.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
T2: Makes images appear bluish white.
T3: Maintains normal colorings for white.
33
4.
T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1.
Go to the DISPLAY menu and highlight Color Management.
2.
Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3.
Highlight Primary Color and press
Green, Cyan, Blue, or Magenta.
/
to select a color from among Red, Yellow,
4.
Press
to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
Yellow
range at 0, only pure red in the projected
GREEN
RED
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
5.
Press
to highlight Saturation and adjust
its values to your preference by pressing
Cyan
Magenta
/
BLUE
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6.
7.
8.
9.
Press
to highlight Gain and adjust its values to your preference by pressing
/
. The contrast level of the primary color you select will be affected. Every
adjustment made will reflect to the image immediately.
Repeat steps 3 to 6 for other color adjustments.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT on the projector or Exit on the remote control to exit and save the
settings.
34
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1.
Press Timer on the remote control to access the Presentation Timer menu or go to
the SYSTEM SETTING: ADVANCED > Presentation Timer menu and press
MODE/ENTER to display the Presentation Timer page.
2.
Highlight Timer Period and decide the time period by pressing / . The length of
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3.
Press
to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing
/
.
Selection
Description
Displays the timer on screen throughout the presentation
Always
time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never
Hides the timer throughout the presentation time.
4.
Press
to highlight Timer Position and set the timer position by pressing
Top-Left
5.
Press
Bottom-Left
Selection
Count Up
Count Down
Press
.
Bottom-Right
to highlight Timer Counting Direction and select your desired counting
direction by pressing
6.
Top-Right
/
/
.
Description
Increases from 0 to the preset time.
Decreases from the preset time to 0.
to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / . If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
7.
8.
To activate the presentation timer, press
and press / to highlight Start
Counting and press MODE/ENTER.
A confirmation message displays. Highlight Yes and press MODE/ENTER on the
projector or remote control to confirm. You will see the message “Timer is On”
displaying on the screen. The timer starts counting when the timer is on.
To cancel the timer, perform the following steps:
1.
2.
Go to the SYSTEM SETTING: ADVANCED > Presentation Timer menu and
highlight Off. Press MODE/ENTER. A confirmation message displays.
Highlight Yes and press MODE/ENTER to confirm. You will see the message
“Timer is Off” displaying on the screen.
35
Hiding the image
In order to draw the audience's full attention to the presenter, you can use
on the
projector or Blank on the remote control to hide the screen image. Press any key on the
projector or remote control to restore the image. The word 'BLANK' appears at the lower
right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETTING: BASIC > Blank Timer menu to
let the projector return the image automatically after a period of time when there is no action
taken on the blank screen.
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except
1.
Press
I
I
POWER.
on the remote control, or go to the SYSTEM
on the projector or Lock
SETTING: BASIC > Panel Key Lock menu, and select On by pressing
2.
/
on
the projector or remote control.
A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, press and hold
control for 3 seconds.
on the projector or Lock
on the remote
You can also use the remote control to enter the SYSTEM SETTING: BASIC > Panel
Key Lock menu and press / to select Off.
•
Keys on the remote control are still functional when panel key lock is enabled.
•
If you press I POWER to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
I
Freezing the image
Press Freeze on the remote control to freeze the image. The word 'FREEZE' will be
displayed in the upper left corner of the screen. To release the function, press any key on the
projector or remote control.
Even if an image is frozen on the screen, the pictures are running on the video or other
device. If the connected devices have active audio output, you will still hear the audio even
though the image is frozen on screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
36
To activate the High Altitude Mode:
1.
Press MENU/EXIT on the projector or Menu on
the remote control and then press / until the
SYSTEM SETTING: ADVANCED menu is
highlighted.
2.
Press
to highlight High Altitude Mode and
Notice
We recommend you use the High Altitude
mode by selecting it whenever your
environment is higher than 1500 m.
Do you want to turn High Altitude
Mode ON?
Yes
No
press / to select On. A confirmation
message is displayed.
3.
Highlight Yes and press MODE/ENTER on the projector or Enter on the remote
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Using the CEC function
This projector supports CEC (Consumer Electronics Control) function for synchronized
power on/off operation via HDMI connection. That is, if a device that also supports CEC
function is connected to the HDMI input of the projector, when the projector’s power is
turned off, the power of the connected device will also be turned off automatically. When
the power of the connected device is turned on, the projector’s power will be turned on
automatically.
To turn on the CEC function:
1.
2.
3.
Press MENU/EXIT on the projector or Menu on the remote control to open the OnScreen Display (OSD) menu.
Go to the SYSTEM SETTING: BASIC > CEC menu.
Press
/
to select On.
•
In order for the CEC function to work properly, make sure that the device is correctly
connected to the HDMI input of the projector via a HDMI cable, and its CEC function is
turned on.
•
Depending on the connected device, the CEC function may not work.
Using the 3D functions
This projector features 3D function which enables you to enjoy 3D movies, videos, and
sporting events in a more realistic way by presenting the depth of the images. You need to
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the
signal for 3D Sync information and once detected, it projects images in 3D format
automatically. In other cases, you may need to manually select a 3D Sync format for the
projector to project 3D images correctly.
To select a 3D Sync format:
37
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the DISPLAY menu is highlighted.
2.
Press
to highlight 3D Settings and press MODE/ENTER on the projector or
Enter on the remote control.
3.
Press
to highlight 3D Sync and press MODE/ENTER on the projector or Enter
on the remote control.
4.
Press
to select a 3D Sync setting according to the table below and then press
MODE/ENTER on the projector or Enter on the remote control to confirm.
When the 3D Sync function is on:
•
The brightness level of the projected image will decrease.
•
The Color Mode cannot be adjusted.
•
The Zoom can only magnify the pictures to limited sizes.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert”
to correct the problem.
38
Controlling the projector through a LAN
environment
The projector supports Crestron® software. With correct settings for the LAN Control
Settings menu, you can manage the projector from a computer using a web browser when
the computer and the projector are properly connected to the same local area network.
(An example of connection)
Configuring the LAN Control Settings
If you are in a DHCP environment:
1.
2.
Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the SYSTEM SETTING: BASIC menu is highlighted.
3.
Press
to highlight LAN Control Settings and press MODE/ENTER on the
projector or Enter on the remote control. The LAN Control Settings page is
displayed.
4.
Press
5.
Press
to highlight Apply and press MODE/ENTER on the projector or Enter on
the remote control.
Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings
page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server
settings will be displayed. Note down the IP address displayed in the Projector IP
Address row.
6.
to highlight DHCP and press
/
to select On.
•
If the Projector IP Address still does not appear, contact your network administrator.
•
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
•
If you need to connect to the projector in its standby mode, set Power Saving to Off.
If you are in a non-DHCP environment:
1.
Repeat steps 1-3 above.
2.
3.
Press
to highlight DHCP and press / to select Off.
Contact your ITS administrator for information on the Projector IP Address, Subnet
Mask, Default Gateway, and DNS Server settings.
39
4.
Press
to select the item you want to modify and press MODE/ENTER on the
projector or Enter on the remote control.
5.
6.
Press / to move the cursor and the press
/
to enter the value.
To save the settings, press MODE/ENTER on the projector or Enter on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
or Menu on the remote control.
7.
Press
to highlight Apply and press MODE/ENTER on the projector or Enter on
the remote control.
•
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
•
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS
Server information when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
•
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
•
The screen shots in this manual are for reference only, and may differ from the actual
design.
1.
Enter the address of the projector in the address bar of your browser and press Enter.
2.
The main page of the Network Control appears.
3
4
5
Accessing to Network Settings or Email Alert page requires Administrator password. The
default password is "0000".
3.
This page allows you to make adjustments to the AMX and SNMP settings. In the
AMX device discover row, when ON is selected, the projector can be detected by
40
controllers of AMX connected to the same network. For the Details of AMX Device
Discovery, visit the AMX web site at http://www.amx.com/.
4.
If your projector is connected to a network which supports Simple Mail Transfer
Protocol (SMTP), you can configure it to alert you via email on significant events.
5.
The Crestron (e-Control) page displays the Crestron e-Control user interface. See
"About Crestron e-Control®" on page 42 for details.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Category Item
Network
Input Length
Maximum Number
of Characters
DHCP/Manual
(N/A)
IP Address
XXX.XXX.XXX.XXX
Subnet Mask
XXX.XXX.XXX.XXX
Gateway
XXX.XXX.XXX.XXX
DNS Server
XXX.XXX.XXX.XXX
AMX device discovery (N/A)
Network Settings
Password
SNMP
41
Administrator
(N/A)
New Password
4
Confirm Password
4
SysLocation
22
SysName
22
SysContact
22
To
Email Setting
SMTP Setting
Email Alert
Alert Condition
40
Cc
40
Subject
40
From
40
Server
30
User Name
21
Password
14
Fan Error
(N/A)
Lamp Error
(N/A)
Over Temperature
(N/A)
Lamp Time Alert
(N/A)
Submit
(N/A)
Issue Test Mail
(N/A)
/ > < $ % + \ ' " are prohibited.
About Crestron e-Control®
The Crestron e-Control® page provides a variety of virtual keys to control the
projector or adjust the projected pictures.
1.
i
ii
You can press
i
i
/
to reveal
more buttons.
i. These buttons function the same as the ones on the OSD menus or remote control.
See "2. PICTURE menu" on page 52 and "Projector" on page 7 for details.
ii. To switch between input signals, click on your desired signal.
•
The Menu button can also be used to go back to previous OSD menus, exit and save menu
settings.
•
The source list varies according to the connectors available on the projector.
•
When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
42
2.
The tools page allows you to manage the projector, configure the LAN control
settings and secure access of remote network operation on this projector.
i
ii
iv
iii
v
vi
i. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been
password-protected.
v. Once set, access to the tools page has been password-protected.
•
To prevent errors, only input the English alphabet and digits on the tools page.
•
After making the adjustments, press the Send button and the data will be saved for the
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Category Item
Crestron Control
Projector
Network Configuration
Input Length
Maximum Number of
Characters
IP Address
16
IP ID
4
Port
5
Projector Name
32
Location
32
Assigned To
32
DHCP (Enabled)
(N/A)
IP Address
16
Subnet Mask
16
Default Gateway
16
DNS Server
16
43
User Password
Admin Password
3.
Enabled
(N/A)
New Password
26
Confirm
26
Enabled
(N/A)
New Password
26
Confirm
26
The info page displays the information and status of this projector.
Press Exit to
go back to the
remote network
operation page.
4.
After pressing the button “Contact IT Help”, the HELP DESK window will appear in
the upper right corner of the screen. You will be able to deliver messages to
RoomView™ software administrators/users who connect to the same local area
network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s
on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron
control port.
About Crestron RoomView™ setting and command method, please access below website to
get RoomView™ User Guide and more information:
http://www.crestron.com/products/roomview_connected_embedded_projectors_devices/
resources.asp
44
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details,
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
SYSTEM SETTING: BASIC > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 0.5W power consumption when Power Saving mode is turned on.
When Power Saving is On, the network function is not available when the projector is in
standby mode.
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only
from COMPUTER IN 1.
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN and AUDIO OUT sockets are
correctly connected to devices.
Quick Power Off
Selecting On enables the function and the projector will not enter the cooling process after
being shut down. Selecting Off disables the function and the projector will enter normal
cooling process after being shut down.
•
If you attempt to restart the projector right after it’s been turned off, it may not be turned
on successfully and will rerun its cooling procedure.
•
When Off is selected, the Smart Restart function will be automatically turned off.
45
Shutting down the projector
1.
2.
3.
Press II POWER and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
RS-2 32
LAN
MINI USB
Press II POWER a second time.
Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
•
To protect the lamp, the projector will not respond to any commands during the cooling
process.
•
To shorten the cooling time, you can also activate the Quick Power Off function. See
"Quick Power Off" on page 45 for details.
•
Do not unplug the power cord before the projector shutdown sequence is complete.
46
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu
Sub-menu
Options
Off/Blackboard/Greenboard/
Whiteboard
Auto/4:3/16:9/
16:10 (PJD6543w only)/Wide
(PJD6543w only)/Anamorphic
(PJD6235/PJD6245 only)
Screen Color
Aspect Ratio
1.
DISPLAY
Keystone
Position
Phase
H. Size
Zoom
3D Settings
Color
Management
Color Mode
Reference Mode
2.
PICTURE
Auto/Off/Frame Sequential/
Frame Packing/Top-Bottom/
Side-by-Side
Disable/Invert
R/G/B/C/M/Y
3D Sync
3D Sync Invert
Primary Color
Hue
Saturation
Gain
PC source: Brightest/PC/ViewMatch/Movie/Dynamic
PC/Dynamic Movie/User 1/User 2
Video source: Brightest/Gaming/ViewMatch/Movie/
Dynamic Movie/User 1/User 2
PC source: Brightest/PC/ViewMatch/Movie/Dynamic
PC/Dynamic Movie
Video source: Brightest/Gaming/ViewMatch/Movie/
Dynamic Movie
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color
Color Temperature
Save Settings
On/Off
T1/T2/T3/T4
47
Main menu
Sub-menu
Options
Quick Auto Search
HDMI Format
HDMI Range
3. SOURCE
4.
SYSTEM
SETTING:
BASIC
Off/On
RGB/YUV/Auto
Enhanced/Normal
Disable/5 min/10 min/15 min/30
DynamicEco Timer
min
Smart Restart
Off/On
Pattern
Off/01/02/03/04/05
Projection (Projector Position)/3D Sync/Lamp Mode/
DCR/Closed Caption/Auto Off (Auto Power Off)/
My Button
Message/Screen Color/CEC/Auto Search (Quick Auto
Search)/Information
Language
Multi-language OSD selection
Front Table/Rear Table/Rear
Projector Position
Ceiling/Front Ceiling
Disable/5 min/10 min/20 min/30
Auto Power Off
min/40 min/50 min/60 min
Disable/5 min/10 min/15 min/20
Blank Timer
min/25 min/30 min
Timer
Off/30 min/1 hour/2 hours/3
Sleep Timer
hours/4 hours/8 hours/12
hours
Panel Key Lock
On/Off
Splash Screen
Black/Blue/ViewSonic/Off
Message
On/Off
DHCP
On/Off
Projector IP Address
Subnet Mask
LAN Control
Settings
Default Gateway
DNS Server
Apply
Power Saving
On/Off
Active VGA Out
On/Off
Standby Settings
Active Audio Out
On/Off
Quick Power Off
On/Off
CEC
On/Off
48
High Altitude Mode
DCR
Audio Settings
Mute
Volume
5 sec/10 sec/15 sec/20
sec/25 sec/30 sec
Menu Settings
Center/Top-Left/TopMenu Position
Right/Bottom-Left/
Bottom-Right
Closed Caption Enable On/Off
Closed Caption
Caption Version
CC1/CC2/CC3/CC4
Lamp Mode
Normal/Economic
Lamp Settings
Reset Lamp Timer
Equivalent Lamp Hour
Timer Period
1~240 minutes
Always/1 min/2 min/3 min/
Timer Display
Never
Top-Left/Bottom-Left/TopTimer Position
Right/Bottom-Right
Presentation Timer
Timer Counting
Count Down/Count Up
Direction
Sound Reminder
On/Off
Start Counting/Off
Change Password
Security Settings
Power On Lock
On/Off
Remote Control Code
A/B
Reset All Settings
Reset/Cancel
Reset Settings
Reset Color Settings
Menu Display Time
5.
SYSTEM
SETTING:
ADVANCED
On/Off
On/Off
On/Off
49
Main menu
6.
INFORMATION
Sub-menu
Options
•
•
•
•
•
•
Current System Status
50
Source
Color Mode
Resolution
Color System
Equivalent Lamp Hour
MAC Address
Description of each menu
Function
Screen Color
Aspect Ratio
Keystone
1. DISPLAY menu
Position
Description
Corrects the projected picture’s color when the projection surface is
not white. See "Using Screen Color" on page 32 for details.
There are several options to set the image's aspect ratio depending on
your input signal source. See "Selecting the aspect ratio" on page 28
for details.
Corrects any keystoning of the image. See "Correcting keystone" on
page 27 for details.
Displays the position adjustment page. To move the projected image,
use the directional arrow keys. The values shown on the lower
position of the page change with every key press you made until they
reach their maximum or minimum.
Adjusts the clock phase to reduce image
distortion.
Phase
H. Size
Adjusts the horizontal width of the image.
Zoom
Magnifies or reduces the projected image. See "Magnifying and
searching for details" on page 27 for details.
3D Settings
See "Using the 3D functions" on page 37 for details.
Color
Management
See "Color Management" on page 34 for details.
51
Function
Color Mode
Reference
Mode
Brightness
2. PICTURE menu
Contrast
Color
Tint
Description
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting a
picture mode" on page 31 for details.
Selects a picture mode that most suits your need for the image quality
and further fine-tune the image based on the selections listed on the
same page below. See "Setting the User 1/User 2 mode" on page 32
for details.
Adjusts the brightness of the image. See "Adjusting Brightness" on
page 33 for details.
Adjusts the degree of difference between dark and light in the image.
See "Adjusting Contrast" on page 33 for details.
Adjusts the color saturation level -- the amount of each color in a
video image. See "Adjusting Color" on page 33 for details.
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 33 for details.
The function is only available when Video or S-Video with NTSC
system is selected.
Sharpness
Brilliant Color
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 33 for details.
Adjusts white peaking while maintaining correct color presentation.
See "Adjusting Brilliant Color" on page 33 for details.
Color
Temperature
See "Selecting a Color Temperature" on page 33 for details.
Save Settings
Saves the settings made for the User 1 or User 2 mode.
52
Function
Quick Auto
Search
Description
See "Switching input signal" on page 25 for details.
HDMI Format
See "Changing HDMI input settings" on page 25 for details.
HDMI Range
3. SOURCE menu
DynamicEco
Timer
Allows the projector to decrease the power consumption automatically
if no input signal is detected after a set period of time.
It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes.
Selecting On enables you to restart the projector immediately within
150 seconds after turning it off. After 150 seconds, if the projector is
not turned on again, it will directly enter the standby mode.
Smart
Restart
•It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes.
If the projector is resumed by using the Smart Restart feature,
this function can be executed immediately.
•When On is selected, the Quick Power Off function will be
automatically set to “On”.
Pattern
The projector can display several test patterns. It helps you adjust the
image size and focus and check that the projected image is free from
distortion.
My Button
Sets a hotkey on remote control.
53
Function
Description
Language
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 21 for details.
The projector can be installed on a ceiling or behind a screen, or
with one or more mirrors. See "Choosing a location" on page 12 for
details.
Allows the projector to turn off automatically if no input signal is
detected after a set period of time. See "Setting Auto Power Off" on
page 58 for details.
Blank Timer
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen. See "Hiding the image"
on page 36 for details.
Projector
Position
Auto Power
Off
4. SYSTEM SETTING: BASIC menu
Timer
Sleep Timer
Allows the projector to turn off automatically after a set period of
time if the incoming signal is present or not.
Disables or enables all panel key functions except II POWER on
the projector and keys on the remote control. See "Locking control
keys" on page 36 for details.
you to select which logo screen will be displayed during
Splash Screen Allows
projector start-up.
Selecting On displays the current information on the screen when
Message
the projector is detecting or searching for a signal.
Panel Key
Lock
LAN Control
Settings
See "Controlling the projector through a LAN environment" on page
39 for details.
Standby
Settings
See "Using the projector in standby mode" on page 45 for details.
CEC
See "Using the CEC function" on page 37 for details.
54
Function
High Altitude
Mode
DCR
Description
A mode for operation in high altitude areas. See "Operating in a high
altitude environment" on page 36 for details.
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and economic
modes according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may shorten
lamp life and noise level will vary during operation.
The sound adjustments made as below will have an effect on the
projector speaker. Be sure you have made a correct connection to the
projector audio input/output jacks. See "Connection" on page 15 for
more details.
5. SYSTEM SETTING: ADVANCED menu
Audio Settings Mute
Mutes the sound received from AUDIO IN.
Menu Settings
Volume
Adjusts the sound level received from AUDIO IN.
Menu Display Time
Sets the length of time the OSD will remain active after your last key
press. The range is from 5 to 30 seconds in 5-second increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed Caption Enable
Activates the function by selecting On when the selected input signal
carries closed captions.
•
Closed
Caption
Captions: An on-screen display of the dialogue, narration, and
sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
This function is only available when a Composite video or SVideo input signal is selected and its system format is NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions, select
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary
language in your area).
Lamp Mode
See "Setting Lamp Mode as Economic" on page 58 for details.
Reset Lamp Timer
Lamp Settings See "Resetting the lamp timer" on page 62 for details.
Equivalent Lamp Hour
See "Getting to know the lamp hour" on page 58 for details on how
the total lamp hour is calculated.
55
Function
Description
5. SYSTEM SETTING: ADVANCED menu
Presentation
Timer
Reminds the presenter to finish the presentation within a certain time
frame. See "Setting the presentation timer" on page 35 for details.
Security
Settings
See "Utilizing the password function" on page 22 for details.
Remote
Control Code
See "Remote control code" on page 9 for details.
Reset All Settings
Returns all settings to the factory preset values.
Reset Settings
The following settings will still remain: Keystone, Language,
Projector Position, High Altitude Mode, Security Settings,
Remote Control Code.
Reset Color Settings
Returns all color settings to the factory preset values.
Source
Shows the current signal source.
6. INFORMATION menu
Color Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Current
System Status Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
MAC Address
Shows the MAC Address of your projector.
MAC Address stands for Media Access Control Address, which
is a physical layer address used to uniquely identify a network
node.
56
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 46 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
•
•
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 65 or
consult your dealer about the range.
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
57
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the SYSTEM SETTING: ADVANCED menu is highlighted.
2.
Press
to highlight Lamp Settings and press MODE/ENTER on the projector or
ENTER on the remote control. The Lamp Settings page is displayed.
3.
You will see the Equivalent lamp hour information on the menu.
4.
To leave the menu, press MENU/EXIT on the projector or Exit on the remote
control.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETTING: ADVANCED > Lamp Settings >
Lamp Mode menu and press
/
.
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETTING: BASIC > Auto Power Off
menu and press / . If the preset time lengths are not suitable for your presentation,
select Disable. The projector will not automatically shut down in a certain time period.
58
Timing of replacing the lamp
When the LAMP indicator light lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the LAMP or TEMP indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 63 for details.
The following lamp warning displays will remind you to change the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
(See "Setting Lamp Mode as Economic" on page
58), you may continue to operate the projector
until the next hour lamp warning appears.
Notice
Order Replacement Lamp
Lamp > ____ Hours
OK
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of lamp
time.
Notice
Replace Lamp Soon
Lamp > ____ Hours
OK
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced when
you see this message.
The lamp MUST be replaced before the projector
will operate normally.
Notice
Replace Lamp Now
Lamp > ____ Hours
Lamp usage time exceeded
OK
Notice
Out of Lamp Usage Time
Replace lamp (refer to User Manual)
Then reset lamp timer
OK
59
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number: RLC-078 (PJD6235/PJD6245)
Type number: RLC-085 (PJD6543w)
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org
•
Be careful of broken glass when replacing the lamp.
•
Please wear eye protection and gloves when performing overhead installation.
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
•
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
•
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces. Before replacing the
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp
edges in the lamp compartment. Wash hands after lamp replacement.
•
Only ViewSonic certified lamps are tested with this projector. Use of other lamps may
cause electrical shock and fire.
1.
2.
3.
Turn the power off and disconnect the
projector from the wall socket. If the lamp
is hot, avoid burns by waiting for
approximately 45 minutes until the lamp
has cooled.
Loosen the screws that secure the lamp
cover on the both sides of the projector until
the lamp cover loosens.
Remove the lamp cover from the projector.
WARNING
•
Do not turn the power on with the lamp cover
removed.
•
Do not insert your fingers between the lamp
and the projector. The sharp edges inside the
projector may cause injuries.
Remove and dispose of the lamp protection film.
60
4.
Loosen the screw that secures the lamp.
5.
Disconnect the lamp’s wire connector from
the projector, and then lift the handle so that
it stands up. Use the handle to slowly pull
the lamp out of the projector.
2
1
CAUTION
•
Pulling it too quickly may cause the lamp to
break and scatter broken glass in the projector.
•
Do not place the lamp in locations where water
might splash on it, children can reach it, or
near flammable materials.
•
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause color
unevenness and distortion of the projected
images.
6.
Insert the new lamp into the lamp
compartment and make sure it fits in the
projector. Connect the new lamp’s wire
connector to the projector.
7.
Tighten the screw that secures the lamp.
CAUTION
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
8.
Ensure the handle is fully laid flat and
locked in place.
61
3
9.
10.
11.
Place the lamp protection film supplied
with the new lamp on the lamp
compartment.
Replace the lamp cover on the projector.
Tighten the screws that secure the lamp
cover.
CAUTION
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screws.
12.
Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
13.
14.
15.
16.
After the startup logo, open the On-Screen
Display (OSD) menu.
Go to the SYSTEM SETTING:
ADVANCED > Lamp Settings menu. Press
MODE/ENTER on the projector or ENTER
on the remote control. The Lamp Settings
page is displayed.
Press
to highlight Reset lamp timer and
press MODE/ENTER on the projector or
ENTER on the remote control. A warning
message is displayed asking if you want to
reset the lamp timer.
Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote
control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this
could cause damage.
62
Notice
Reset Lamp Timer
Reset
Cancel
Indicators
Light
POWER TEMP
Status & Description
LAMP
Power events
Blue
Flashing
Off
Off
Stand-by mode
Blue
Off
Off
Blue
Off
Off
Powering up
Normal operation
Blue
Flashing
Off
Off
Normal power-down cooling
Lamp events
Blue
Flashing
Off
Red
Off
Off
Red
Blue
Off
Red
The projector needs 60 seconds to cool down.
The projector has shut down automatically. If you try
to re-start the projector, it will shut down again.
Please contact your dealer for assistance.
CW start fail (30sec)
Thermal events
Off
Red
Off
Off
Red
Red
Purple
Red
Red
The projector has shut down automatically. If you try
to re-start the projector, it will shut down again.
Please contact your dealer for assistance.
63
Troubleshooting
The projector does not turn on.
Cause
Remedy
There is no power from the power
cord.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with a new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 8 meters (26 feet) of the
projector.
64
Specifications
Projector specifications
•
All specifications are subject to change without notice.
•
Not all models can be purchased in your region.
General
Product name
DLP Projector
Optical
Resolution
Display system
Lamp
PJD6235/PJD6245:
1024 x 768 XGA
PJD6543w:
1280 x 800 WXGA
1-CHIP DMD
190 W lamp
Electrical
Power supply
Power consumption
AC100–240V, 50-60 Hz (Automatic)
250 W (Max); < 0.5W (Standby)
Mechanical
Weight
2.1 Kg (4.63 lbs)
Input terminal
Computer input
RGB input
Video signal input
S-VIDEO
VIDEO
SD/HDTV signal input
Analog –
D-Sub 15-pin (female) x 2
Mini DIN 4-pin port x 1
RCA jack x 1
D-Sub <–> Component RCA jack x 3
(through RGB input)
Digital – HDMI V1.4a x 1
Audio signal input
PC audio jack x 1
65
Output terminal
RGB output
Audio signal output
Speaker
D-Sub 15-pin (female) x 1
PC audio jack x 1
2 watt x 1
Control terminal
RS-232 serial control
LAN
USB serial control
IR receiver
9 pin x 1
RJ45 x 1
Type mini B
x 1 (Front)
Environmental Requirements
Operating temperature
Operating relative
humidity
Operating altitude
0°C–40°C at sea level
10%–90% (without condensation)
•
•
0–1499 m at 5°C–35°C
1500–3000 m at 5°C–25°C (with High Altitude Mode on)
66
Dimensions
268 mm (W) x 84.4 mm (H) x 221 mm (D) (Excluding extrusions)
268
221
MENU
EXIT
84.4
Ceiling mount installation
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
81.5
81.5
110.05
55
Unit: mm
67
Timing chart
Supported timing for PC input
Resolution
Mode
720 x 400
720x400_70
VGA_60**
VGA_72
VGA_75
VGA_85
SVGA_60**
SVGA_72
SVGA_75
SVGA_85
SVGA_120*
(Reduce Blanking)
XGA_60**
XGA_70
XGA_75
XGA_85
XGA_120*
(Reduce Blanking)
1280x720_120*
WXGA_60**
WXGA_75
WXGA_85
SXGA_60**
SXGA_75
SXGA_85
1280 x 960_60**
SXGA+_60**
UXGA**
MAC13
MAC16
MAC21
640 x 480
800 x 600
1024 x 768
1280x720
1280 x 800
1280 x 1024
1280 x 960
1400X1050
1600x1200
640x480@67Hz
832x624@75Hz
1152x870@75Hz
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
Pixel
Frequency
(MHz)
70.087
59.940
72.809
75.000
85.008
60.317
72.188
75.000
85.061
31.469
31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
28.3221
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
119.854
77.425
83.000
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
119.989
97.551
115.500
120
59.810
74.934
84.880
60.020
75.025
85.024
60.000
59.978
60.000
66.667
74.546
75.06
90.000
49.702
62.795
71.554
63.981
79.976
91.146
60.000
65.317
75.000
35.000
49.722
68.68
148.500
83.500
106.500
122.500
108.000
135.000
157.500
108
121.750
162.000
30.240
57.280
100.00
•
*Supported timing for 3D signal with Frame Sequential format.
•
**Supported timing for 3D signal with Frame Sequential, Top-Bottom, and Side-by-Side
formats.
68
Supported timing for Component-YPbPr input
Timing
Resolution
Horizontal
frequency
(KHz)
Vertical
Frequency
(Hz)
Dot Clock
Frequency
(MHz)
480i*
480p*
576i*
576p*
720/50p
720/60p
1080/50i
1080/60i
1080/50P
1080/60P
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
56.25
67.5
59.94
59.94
50
50
50
60
50
60
50
60
13.5
27
13.5
27
74.25
74.25
74.25
74.25
148.5
148.5
*Supported timing for 3D signal with Frame Sequential format.
Supported timing for Video and S-Video inputs
Video mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Color sub-carrier
Frequency (MHz)
NTSC*
PAL*
SECAM*
PAL-M*
PAL-N*
PAL-60*
NTSC4.43*
15.73
15.63
15.63
15.73
15.63
15.73
15.73
60
50
50
60
50
60
60
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
*Supported timing for 3D signal with Frame Sequential format.
Supported timing for HDMI input
Video Mode
Resolution
Horizontal
frequency
(KHz)
Vertical
Frequency
(Hz)
Dot Clock
Frequency
(MHz)
480i*
480p*****
576i*
576p*****
720/50p***
720/60p***
1080/50i****
1080/60i****
1080/24P**
1080/50P
1080/60P
720(1440) x 480
720 x 480
720(1440) x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
56.25
67.5
59.94
59.94
50
50
50
60
50
60
24
50
60
27
27
27
27
74.25
74.25
74.25
74.25
74.25
148.5
148.5
•
*Supported timing for 3D signal with Frame Sequential format.
•
**Supported timing for 3D signal with Frame Packing and Top-Bottom formats.
•
***Supported timing for 3D signal with Frame Sequential, Frame Packing, and Top-Bottom
formats.
•
****Supported timing for 3D signal with Side-by-Side format.
69
•
*****Supported timing for 3D signal with Frame Sequential and Top-Bottom formats.
Resolution
Mode
720 x 400
720x400_70
VGA_60**
VGA_72
VGA_75
VGA_85
SVGA_60**
SVGA_72
SVGA_75
SVGA_85
SVGA_120*
(Reduce Blanking)
XGA_60**
XGA_70
XGA_75
XGA_85
XGA_120*
(Reduce Blanking)
1280x720_120*
WXGA_60**
WXGA_75
WXGA_85
SXGA_60**
SXGA_75
SXGA_85
1280 x 960_60**
SXGA+_60**
UXGA**
MAC13
MAC16
MAC21
640 x 480
800 x 600
1024 x 768
1280x720
1280 x 800
1280 x 1024
1280 x 960
1400X1050
1600x1200
640x480@67Hz
832x624@75Hz
1152x870@75Hz
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
Pixel
Frequency
(MHz)
70.087
59.940
72.809
75.000
85.008
60.317
72.188
75.000
85.061
31.469
31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
28.3221
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
119.854
77.425
83.000
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
119.989
97.551
115.500
120
59.810
74.934
84.880
60.020
75.025
85.024
60.000
59.978
60.000
66.667
74.546
75.06
90.000
49.702
62.795
71.554
63.981
79.976
91.146
60.000
65.317
75.000
35.000
49.722
68.68
148.500
83.500
106.500
122.500
108.000
135.000
157.500
108
121.750
162.000
30.240
57.280
100.00
•
*Supported timing for 3D signal with Frame Sequential format.
•
**Supported timing for 3D signal with Frame Sequential, Top-Bottom, and Side-by-Side
formats.
70
Copyright information
Copyright
Copyright 2012. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
71
Appendix
IR control table
Code A
Key
Format Byte1 Byte2 Byte3 Byte4
Power
NEC
83
F4
17
Auto Sync
NEC
83
F4
08
E8
F7
VGA
NEC
83
F4
41
BE
AD
Video
NEC
83
F4
52
Source
NEC
83
F4
04
FB
Color Mode
NEC
83
F4
10
EF
Up / KeyS +
NEC
83
F4
0B
F4
Left
NEC
83
F4
0E
F1
Enter
NEC
83
F4
15
EA
Right
NEC
83
F4
0F
F0
Down / KeyS -
NEC
83
F4
0C
F3
Menu
NEC
83
F4
30
CF
My Button
NEC
83
F4
56
A9
Exit
NEC
83
F4
28
D7
Mouse L key
NEC
83
F4
36
C9
Mouse R key
NEC
83
F4
37
C8
PgUp
NEC
83
F4
05
FA
PgDn
NEC
83
F4
06
F9
Mouse
NEC
83
F4
31
CE
CD
Magnify
NEC
83
F4
32
Volume +
NEC
83
F4
82
7D
Volume -
NEC
83
F4
83
7C
Panel Key Lock
NEC
83
F4
57
A8
Freeze
NEC
83
F4
03
FC
AA
Pattern
NEC
83
F4
55
Blank
NEC
83
F4
07
F8
Mute
NEC
83
F4
14
EB
DynamicEco™
NEC
83
F4
2B
D4
Timer
NEC
83
F4
27
D8
Aspect
NEC
83
F4
13
EC
72
Code B
Key
Format Byte1 Byte2 Byte3 Byte4
Power
NEC
83
F4
60
9F
Auto Sync
NEC
83
F4
63
9C
VGA
NEC
83
F4
64
9B
Video
NEC
83
F4
66
99
Source
NEC
83
F4
7D
82
Color Mode
NEC
83
F4
9E
61
Up / KeyS +
NEC
83
F4
67
98
Left
NEC
83
F4
69
96
Enter
NEC
83
F4
6B
94
Right
NEC
83
F4
6A
95
Down / KeyS -
NEC
83
F4
68
97
Menu
NEC
83
F4
6C
93
My Button
NEC
83
F4
6D
92
Exit
NEC
83
F4
6E
91
Mouse L key
NEC
83
F4
38
C7
Mouse R key
NEC
83
F4
39
C6
PgUp
NEC
83
F4
5C
A3
PgDn
NEC
83
F4
5D
A2
Mouse
NEC
83
F4
9B
64
Magnify
NEC
83
F4
99
66
Volume +
NEC
83
F4
5A
A5
Volume -
NEC
83
F4
5B
A4
Panel Key Lock
NEC
83
F4
5E
A1
9E
Freeze
NEC
83
F4
61
Pattern
NEC
83
F4
7E
81
Blank
NEC
83
F4
62
9D
Mute
NEC
83
F4
9D
62
DynamicEco™
NEC
83
F4
7F
80
Timer
NEC
83
F4
9C
63
Aspect
NEC
83
F4
9A
65
73
RJ45 response table
Status
Write
Response
Response Code
Normal => ACK
0x03 0x14 0x00 0x00 0x00 0x14
Incorrect => ERROR ACK
0x00 0x14 0x00 0x00 0x00 0x14
Timeout (>100ms)
N/A
Status
Response Code
BYTE0 BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7~N
0x05
Read
0x14
0x00
LSB
MSB
0x00
0x00
Data
BYTE N+1
Checksum
Ex1. Read power status: 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18
= On
Ex2. Read brightness: 0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x32 0x00 0x4A = 50
Ex3. Read lamp hours: 0x05 0x14 0x00 0x06 0x00 0x00 0x00 0x28 0x00
0x00 0x00 0x42
•
The RJ45 commands can only be received via TCP port 4661.
•
Please refer to the below RS232 command table for the commands.
= 40
RS232 command table
<Pin assignment for this two end>
Pin
Description
Pin
Description
1
NC
2
RX
3
TX
4
NC
5
GND
6
NC
7
RTSZ
8
CTSZ
9
NC
<Interface>
RS-232 protocol
Baud Rate
115200 bps (default)
Data Length
8 bit
Parity Check
None
Stop Bit
1 bit
Flow Control
None
<RS232/RJ45 command table>
Function
Status
Write
Power
Read
Action
cmd
Turn on
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Turn off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Power status
(on/off)
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E
Reset
Execute
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Reset Color
Settings
Execute
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87
74
Write
Splash Screen
Read
Quick Power
Off
Write
Read
High Altitude
Mode
Write
Read
Write
Lamp Mode
Read
Message
Write
Read
Projector
Position
Write
Read
3D Sync
Write
Read
Write
3D Sync Invert
Read
Contrast
Write
Read
Splash Screen
Black
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash Screen
Blue
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Splash Screen
ViewSonic
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Splash Screen
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Splash Screen
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68
Quick Power
Off Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
Quick Power
Off On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Quick Power
Off status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B 0x69
High Altitude
Mode Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High Altitude
Mode On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
High Altitude
Mode status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A
Lamp Mode
Normal
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Lamp Mode
Economic
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Lamp Mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E
Message Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Message On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85
Front Table
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Rear Ceiling
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Front Ceiling
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Projector
position status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F
OFF
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
Frame
Sequential
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80
Frame Packing
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81
Top-Bottom
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82
Side-by-Side
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83
3D Sync Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
On
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
3D Sync Invert
Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80
Contrast
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Contrast ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61
75
Brightness
Write
Read
Aspect ratio
Write
Read
Auto Adjust
Horizontal
position
Write
Write
Read
Write
Color
temperature
Read
Blank
Write
Read
KeystoneVertical
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Brightness
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62
Aspect ratio
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio 4:3
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio
16:9
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio
16:10
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Aspect ratio
Wide/
Anamorphic
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68
Aspect ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63
Execute
Read
Vertical
position
Brightness
decrease
Write
Read
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Horizontal
position shift
right
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Horizontal
position shift left
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Horizontal
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65
Vertical position
shift up
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Vertical position
shift down
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
read Vertical
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66
Color
temperatureT1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
Color
temperatureT2
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
Color
temperatureT3
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
Color
temperatureT4
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
Color
temperature
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67
Blank on
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Blank status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68
Decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
Increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
76
Write
Color mode
Read
Write
Primary Color
Read
Hue
Write
Read
Saturation
Write
Read
Gain
Write
Read
Freeze
Write
Read
Source input
Write
Read
Quick Auto
Search
Write
Read
Brightest
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Movie
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
User 1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
User 2
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
PC / Gaming
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
ViewMatch
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Dynamic PC
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x06 0x6F
Dynamic Movie
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x07 0x70
Preset mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A
Primary color R
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Primary color G
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Primary color B
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Primary color C
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Primary color M
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Primary color Y
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Primary color
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F
Hue decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Hue increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Hue
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70
Saturation
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Saturation
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Saturation
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71
Gain decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Gain increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Gain
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72
Freeze on
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze off
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Freeze status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60
Input source
VGA
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Input source
VGA2
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
Input source
Composite
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Input source
SVIDEO
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Input source
HDMI
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Source
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61
Quick Auto
Search on
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto
Search off
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Quick Auto
Search status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62
77
RGB
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85
Write
YUV
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87
Read
HDMI Format
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86
HDMI Format
Write
HDMI Range
Read
Mute
Write
Read
Volume
Write
Read
Enhanced
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86
Normal
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87
HDMI Range
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29 0x87
Mute on
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute off
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Mute status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61
Increase
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Decrease
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Volume
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
Language
Write
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75
Read
Language
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62
Write
Reset Lamp
usage hour
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Read
Lamp usage
hour
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63
Read
Read error
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66
Lamp Time
Error status
78
CEC
Write
Read
Write
Brilliant Color
Read
Remote
Control code
Write
Read
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88
On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89
CEC status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B 0x89
Brilliant Color
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D
Brilliant Color
On
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E
Brilliant Color
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0F 0x6E
Remote Control
code A
0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0
Remote Control
code B
0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1
Remote Control
code status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x048
0xA1
79
Customer Support
For technical support or product service, see the table below or contact your
reseller.
Note : You will need the product serial number.
Country/Region
Website
Australia/New Zealand www.viewsonic.com.au
Canada
Europe
www.viewsonic.com
www.viewsoniceurope.
com
www.hk.viewsonic.com
www.in.viewsonic.com
www.kr.viewsonic.com
T = Telephone
F = FAX
AUS= 1800 880 818
NZ= 0800 008 822
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
Email
service@au.viewsonic.com
service.ca@viewsonic.com
www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong
T= 852 3102 2900
service@hk.viewsonic.com
India
T= 1800 266 0101
service@in.viewsonic.com
Korea
T= 080 333 2131
service@kr.viewsonic.com
Latin America
www.viewsonic.com/la/ T= 0800-4441185
soporte@viewsonic.com
(Argentina)
Latin America (Chile)
www.viewsonic.com/la/ T= 1230-020-7975
soporte@viewsonic.com
Latin America
www.viewsonic.com/la/ T= 01800-9-157235
soporte@viewsonic.com
(Columbia)
Latin America (Mexico) www.viewsonic.com/la/ T= 001-8882328722
soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)
www.viewsonic.com/la/ T= 0800-54565
soporte@viewsonic.com
Macau
www.hk.viewsonic.com T= 853 2870 0303
service@hk.viewsonic.com
Middle East
ap.viewsonic.com/me/
Contact your reseller
service@ap.viewsonic.com
T= 1-800-688-6688 (English)
Puerto Rico & Virgin
service.us@viewsonic.com
www.viewsonic.com
T= 1-866-379-1304 (Spanish)
Islands
soporte@viewsonic.com
F= 1-909-468-3757
Singapore/Malaysia/
www.viewsonic.com.sg T= 65 6461 6044
service@sg.viewsonic.com
Thailand
South Africa
ap.viewsonic.com/za/
Contact your reseller
service@ap.viewsonic.com
T (Toll-Free)= 1-800-688-6688
United States
www.viewsonic.com
T (Toll)= 1-424-233-2530
service.us@viewsonic.com
F= 1-909-468-3757
80
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship
during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a
like product. Replacement product or parts may include remanufactured or refurbished parts or
components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South America: Three
(3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the
RULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH
2WKHUUHJLRQVRUFRXQWULHV3OHDVHFKHFNZLWK\RXUORFDOGHDOHURUORFDO9LHZ6RQLFRI¿FHIRUWKH
warranty information.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours
average daily usage, North and South America: One (1) year warranty for all parts excluding the
ODPSRQH\HDUIRUODERUDQGQLQHW\GD\VIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVW
consumer purchase; Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for
ODERUDQGQLQHW\GD\VIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH
2WKHUUHJLRQVRUFRXQWULHV3OHDVHFKHFNZLWK\RXUORFDOGHDOHURUORFDO9LHZ6RQLFRI¿FHIRUWKH
warranty information.
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V
installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration, failure, or malfunction resulting from:
D $FFLGHQWDEXVHPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHLPSURSHU
PDLQWHQDQFHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHG
with the product.
E 2SHUDWLRQRXWVLGHRISURGXFWVSHFL¿FDWLRQV
c. Operation of the product for other than the normal intended use or not under normal
conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
J &DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH
K 8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
81
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(please refer to “Customer Support” page). You will need to provide your product’s serial
number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic
service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact
ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
LQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVV
opportunity, loss of goodwill, interference with business relationships, or other commercial loss,
even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURP
local authority. Some local governances do not allow limitations on implied warranties and/or do not
allow the exclusion of incidental or consequential damages, so the above limitations and exclusions
may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in www.
viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
82
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the
¿UVWFRQVXPHUSXUFKDVH
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration or malfunction resulting from:
D $
FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFW
PRGL¿FDWLRQXQDXWKRUL]HGDWWHPSWHGUHSDLURUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHGZLWKWKHSURGXFW
b. Any damage of the product due to shipment.
F &DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH
G 8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer
to the attached Customer Support page). You will need to provide your product’s serial number, so please
record the product information in the space provided below on your purchase for your future use. Please
retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: __________________________
Document Number: ____________________ Serial Number: ___________________________
Purchase Date: ________________________Extended Warranty Purchase? _______________(Y/N)
If so, what date does warranty expire? _________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be
liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
ORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\ORVVRIJRRGZLOO
interference with business relationships, or other commercial loss, even if advised of the possibility of
such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
83
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales
SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
84
Download PDF