LCD517/519 User Manual

LCD517/519 User Manual
Colour LCD screen with VGA input
.
TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------- 1
SAFETY PRECAUTIONS -------------------------------------- 1-3
SPECIAL NOTES ON LCD MONITOR --------------------- 3
BEFORE YOU OPERATE THE MONITOR --------------------- 4
FEATURES -------------------------------------------------------- 4
CHECKING THE CONTENTS OF THE PACKAGE ------ 4
INSTALLATION INSTRUCTIONS --------------------------- 4
CONTROLS AND CONNECTORS -------------------------- 6
ADJUSTING THE VIEWING ANGLE ----------------------- 7
OPERATING INSTRUCTIONS ------------------------------------GENERAL INSTRUCTIONS ---------------------------------FRONT PANEL CONTROL-----------------------------------HOW TO ADJUST A SETTING -----------------------------ADJUSTING THE PICTURE ---------------------------------PLUG AND PLAY ------------------------------------------------
8
7
9
10
11-13
14
TECHNICAL SUPPORT(FAQ) -------------------------------------- 15
ERROR MESSAGE & POSSIBLE SOLUTION --------- 16
APPENDIX --------------------------------------------------------------SPECIFICATIONS ----------------------------------------------FACTORY PRESET TIMING TABLE ----------------------CONNECTOR PIN ASSIGNMENT --------------------------
1
17
17
18
19
FOR YOUR SAFETY
Before operating the monitor, please read this manual thoroughly. This manual
should be retained for future reference.
SAFETY PRECAUTIONS
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification to this equipment. It is the responsibilities of the user
to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the cabinet.
Refer servicing to qualified personnel only.
2
PRECAUTIONS
z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls,
it can injure a person and cause serious damage to the appliance. Use only a
cart or stand recommended by the manufacturer or sold with the monitor. If you
mount the monitor on a wall or shelf, use a mounting kit approved by the
manufacturer and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it from
overheating, be sure these openings are not blocked or covered. Do not place
the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near
or over a radiator or heat register. Do not place the monitor in a bookcase or
cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source indicated on
the label. If you are not sure of the type of power supplied to your home, consult
your dealer or local power company.
z The monitor is equipped with a three-pronged grounded plug, a plug with a third
(grounding) pin. This plug will fit only into a grounded power outlet as a safety
feature. If your outlet does not accommodate the three-wire plug, have an
electrician install the correct outlet, or ground the appliance safely. Do not defeat
the safety purpose of the grounded plug.
z Unplug the unit during a lightening storm or when it will not be used for long
period of time. This will protect the monitor from damage due to power surges.
z Do not overload power strips and extension cords. Overloading can result in fire
or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short circuit
parts causing a fire or electric shock. Never spill liquids on the monitor.
z Do not attempt to service the monitor by yourself; opening or removing covers
can expose you to dangerous voltages and other hazards. Please refer all
servicing to qualified service personnel.
z To ensure satisfactory operation, use the monitor only with UL listed computers
which have appropriate configured receptacles marked between 100 - 240V AC,
Min. 5A.
z The wall socket shall be installed near the equipment and shall be easily
accessible.
3
WEEE DECLARATION
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your other household waste.Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment.The
separate collection and recycling of your waste equipment at the time of disposal
will help to conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more information about where
you can drop off your waste equipment for recycling, please contact your local city
office, your household waste disposal service or the shop where you purchased the
product .
Hg DECLARATION
Contains Mercury, Dispose of Properly
SPECIAL NOTES ON LCD MONITOR
The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
• Due to the nature of the fluorescent light, the screen may flicker during initial use.
•
•
•
Turn off the Power Switch and then turn it on again to make sure the flicker
disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours.
In this case, the screen is recovered slowly by changing the image or turning off
the Power Switch for hours.
4
BEFORE YOU OPERATE THE MONITOR
FEATURES
• 43.27cm(17 inches) TFT Color LCD Monitor
• 48.19cm(19 inches) TFT Color LCD Monitor
• Crisp, Clear Display for Windows
• Recommended Resolutions: 1280x1024@60Hz.
• Ergonomic Design
• Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual(including CD-ROM & Warranty Card)
3. Power Cord
4. 15-pin D-Sub Cable
5. Audio Cable
6. Stand(17 inches)
7. Stand Top(17 inches)
8. Base
INSTALLATION INSTRUCTIONS
Install
Remove
(17 inches)
5
(19 inches)
Figure 1
Installing and Removing the Base
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows operation
in either 100/120V AC or 220/240V AC voltage area (No user adjustment is
required.)
3. Connect the AC-power cord into your LCD monitor’s AC-power-input. The ACpower cord may be connected to either a wall power outlet or the power outlet
socket on your PC, depending on the type of power cord supplied with your LCD
monitor.
6
CONTROLS AND CONNECTORS
SIGNAL CABLE
Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s “DSUB” socket, the other end to the computer's VGA port and tighten the two screws
on the cable connector.
Connecting the DVI Cable: Plug the DVI Cable one end to LCD monitor’s “DVI”
socket, the other end to the computer's DVI port and tighten the two screws on the
cable connector.
Connecting the Power Cord: Connect the AC-power cord into your LCD monitor’s
“AC-IN”. The AC-power cord may be connected to either a wall power outlet or the
power outlet socket on your PC, depending on the type of power cord supplied with
your LCD monitor.
Connecting the Audio Cable: Connect the audio cable between the monitor’s
“AUDIO-IN” socket and the PC’s audio output (green port).
(19 inches)
(17 inches)
Figure 2
1.
2.
3.
4.
Connecting Cables
AC-IN socket
AUDIO-IN socket
DVI input socket
D-SUB input socket
7
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the monitor,
then adjust the monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the monitor’s
angle.
• You are able to adjust the monitor’s angle from -5° to 20°.
Figure 3
NOTES
• Do not touch the LCD screen when you change the angle. It may cause damage
or break the LCD screen.
• Careful attention is required not to catch your fingers or hands when you change
the angle.
8
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are
located at front panel of the monitor (See Figure 4). By changing these settings, the
picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will
light up.
Figure 4
External Control Button
EXTERNAL CONTROLS
1.
2.
3.
4.
5.
AUTO / Source / Exit
- / ECO hotkey
+ / Volume+
MENU / Enter
Power button
9
FRONT PANEL CONTROL
•
/Power Button:
Press this button to turn the monitor ON or OFF, and display the monitor’s state.
• Power Indicator:
Blue
Orange
—
—
Power On mode.
Standby mode.
• MENU / ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status.
• - / ECO hotkey:
Activates ECO control when the OSD is off or adjust a function when function is
activated.
• + / Volume+:
Activates the volume control when the OSD is off or adjust a function when
function is activated.
• Auto/ Source / Exit:
1.
2.
3.
When OSD menu is in active status, this button will act as EXIT-KEY (EXIT
OSD menu).
When OSD menu is in off status, press this button to select input Source: DSub/DVI.
When OSD menu is in off status, press this button for 2 seconds to activate
the Auto Adjustment function. The Auto Adjustment function is used to set
the HPos, VPos, Clock and Focus.
OSD Lock Function: To lock the OSD, press and hold the MENU button while the
monitor is off and then press power button to turn the monitor on. To un-lock the
OSD - press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on.
NOTES
• Do not install the monitor in a location near heat sources such as radiators or air
ducts, or in a place subject to direct sunlight, or excessive dust or mechanical
vibration or shock.
• Save the original shipping carton and packing materials, as they will come in
handy if you ever have to ship your monitor.
• For maximum protection, repackage your monitor as it was originally packed at
the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn
stains may be removed with a cloth lightly dampened with a mild detergent
solution. Never use strong solvents such as thinner, benzene, or abrasive
cleaners, since these will damage the cabinet. As a safety precaution, always
unplug the monitor before cleaning it.
• Do not scratch the screen with hard things, it may cause permanent
damage.
• Don’t leak liquid into monitor which will result in the damage of component.
10
HOW TO ADJUST A SETTING
1.
2.
3.
4.
Press the MENU-button to activate the OSD window.
Press - or + to navigate through the functions. Once the desired function is
highlighted, press the MENU-button to activate it. If the function selected has
a sub-menu, press- or + again to navigate through the sub-menu functions.
Once the desired function is highlighted, press MENU-button to activate it.
Press - or + to change the settings of the selected function.
To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5 The OSD Message
11
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Main
Sub Menu
Menu
Menu Item
Item
Icon
Sub
Menu
Description
Brightness
Backlight Adjustment
Contrast
Contrast from Digital-register
Standard Standard Mode
Luminance
Text
Text Mode
Internet
Internet Mode
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Off
Disable dynamic contrast ratio
On
Enable dynamic contrast ratio
Eco
DCR
Clock
Adjust Picture Clock to reduce
Vertical-Line noise
Focus
Adjust Picture Phase to reduce
Horizontal-Line noise
H.Position
Adjust the horizontal position of the
picture
V.Position
Adjust the vertical position of the
picture
Image
Setup
12
Main
Main
Sub Menu
Menu
Menu Item
Item
Icon
Sub
Menu
Description
Warm
Recall Warm Color Temperature
from EEPROM
Normal
Recall Normal Color Temperature
from EEPROM
Cool
Recall Cool Color Temperature
from EEPROM
sRGB
Recall SRGB Color Temperature
from EEPROM
Color
Temp.
User-B
Blue Gain from Digital-register
User-G
Green Gain Digital-register
User-R
Red Gain from Digital-register
Full
Enhance
on or off
Disable or Enable Full Enhance
Mode
Nature
Skin
on or off
Disable or Enable Nature Skin
Mode
Green
Field
on or off
Disable or Enable Green Field
Mode
Sky-blue
on or off
Disable or Enable Sky-blue Mode
User
Color
Boost
AutoDetect on or off
Disable or Enable AutoDetect Mode
Demo
Disable or Enable Demo
on or off
13
Main
Main
Menu
Menu Item
Icon
Picture
Boost
Sub Menu
Item
Sub
Menu
Description
Frame Size
Adjust Frame Size
Brightness
Adjust Frame Brightness
Contrast
Adjust Frame Contrast
H.Position
Adjust the horizontal position of
Frame
V.Position
Adjust the vertical position of
Frame
Bright Frame
on or off Disable or Enable Bright Frame
H.Position
Adjust the horizontal position of
OSD
V.Position
Adjust the vertical position of
OSD
Timeout
Adjust the OSD Timeout
Language
Select the OSD language
OSD Setup
D-Sub
Select analog input source
DVI
Select digital input source
Input Select
DDC/CI
Turn ON/OFF DDC/CI Support
Reset
Reset the menu to default
Information
Show the information of the
main image and sub-image
source
Extra
14
PLUG AND PLAY
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the VESA
DDC STANDARD. It allows the monitor to inform the host system of its identity and,
depending on the level of DDC used, communicate additional information about its
display capabilities. The communication channel is defined in two levels, DDC1 and
DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bidirectional data channel
based on the I²C protocol. The host can request EDID information over the DDC2B
channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO
VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics
Standards Association (VESA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power
consumption when there is no video-input signal present. When there is no video
input signal this monitor, following a time-out period, will automatically switch to an
OFF mode. This reduces the monitor's internal power supply consumption. After the
video input signal is restored, full power is restored and the display is automatically
redrawn. The appearance is similar to a "Screen Saver" feature except the display
is completely off. The display is restored by pressing a key on the keyboard, or
clicking the mouse.
15
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
No Plug & Play
Picture is fuzzy
Picture bounces or a wave
pattern is present in the
picture
The power LED is ON but
there’s no video or no
picture.
Possible Solution
*Check if the Power Switch is in the ON
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video Cable is
bent
*Adjust the Contrast and Brightness
Controls.
*Move electrical devices that may cause
electrical interference.
*Computer Power Switch should be in the
ON position.
*Computer Video Card should be snugly
seated in its slot
*Make sure monitor’s video cable is properly
connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by hitting
the CAPS LOCK key on the keyboard while
observing the CAPS LOCK LED. The LED
should either turn ON or OFF after hitting
the CAPS LOCK key.
*Inspect the monitor’s video cable and make
sure that none of the pins are bent.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
Screen image is not *Adjust pixel frequency (CLOCK) and
centered or sized properly.
FOCUS or press hot-key (AUTO)
Picture has color defects
*Adjust RGB color or select color
(white does not look white)
temperature
Horizontal
or
vertical *Use Win95/98/2000/ME/XP shut-down
disturbances
on
the
mode Adjust CLOCK and FOCUS or
screen
perform hot- key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal
sweep. If the frequency is not correct, the screen shows vertical stripes and the
picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment
the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or Win95/98/2000/ME/XP
shut-down mode pattern.
16
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1.
2.
Check that the signal-cable is properly connected , If the connector is loose,
tighten the connector’s screws.
Check the signal -cable connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table.(page19)
17
APPENDIX
SPECIFICATIONS
LCD
Driving system 17” TFT Color LCD
19” TFT Color LCD
Panel
Size
43.27cm
48.19cm
Pixel pitch
0. 264mm( H )x
0. 294mm( H )x
0.264mm( V )
0.294mm( V )
Input
Video
R,G,B Analog Interface
TMDS signal
H-Frequency 30KHz – 83KHz
V-Frequency 55-75Hz
Display Colors
16.7M Colors
Dot Clock
140MHz
Max. Resolution
1280x1024 @60Hz
Plug & Play
VESA DDC1/2BTM
Input Connector
D-Sub 15pin/ DVI pin24
Input Video Signal
Analog:0.7Vp-p(standard),
75OHM, Positive
Digital: 150≤ Vidiff ≤1200,
20MHz≤ dot clock ≤165MHz
Maximum Screen Size
Horizontal :337.920mm Horizontal : 376.32mm
Vertical : 270.336mm
Vertical : 301.056mm
Power Source
100~240V,50~60Hz,1.5A
Environmental
Operating Temp: 0° to 40°C
Considerations
Storage Temp.: -25° to 55°C
Operating Humidity: 10% to 85%
Weight (N. W.)
3.9 kg Unit
4.2 kg Unit
Dimension
371.6*382.6*190.0mm 409.1*413.4*210.0mm
(with Base)
(W*H*D)
(W*H*D)
Power Consumption
25 Watts
( Maximum )
Switch
Auto/ Source / Exit
- /ECO hotkey
+ /Volume+
Menu / Enter
Power Button
External Functions
• Luminance
Controls:
• Image Setup
• Color Temp.
• Color Boost
• Picture Boost
• OSD Setup
• Extra
Audio Output
1.0W rms (per channel)
Regulatory Compliance FCC、CE
18
Preset Display Modes
STANDARD
HORIZONTAL
Frequency(KHz)
VERTICAL
Frequency (Hz)
640×480 @60Hz
31.469
59.940
640×480 @67Hz
35.000
66.667
640×480 @72Hz
37.861
72.809
640×480 @75Hz
37.500
75.000
720×400 @70Hz
31.469
70.087
800×600 @56Hz
35.156
56.250
800×600 @60Hz
37.879
60.317
800×600 @72Hz
48.077
72.188
800×600 @75Hz
46.875
75.000
832×624 @75Hz
49.725
74.550
1024×768 @60Hz
48.363
60.004
1024×768 @70Hz
56.476
70.069
1024×768 @75Hz
60.023
75.029
1152 x 864 @ 75Hz
67.500
75.000
1280 x 960 @ 60Hz
60.000
60.000
1280x1024@60Hz
63.981
60.020
1280x1024@75Hz
79.976
75.025
RESOLUTION
VGA
Dos-mode
SVGA
Mac-Mode
XGA
SXGA
19
CONNECTOR PIN ASSIGNMENT
1
5
6
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
1.
2.
3.
4.
5.
6.
7.
8.
DESCRIPTION
Red
Green
Blue
Logic Gnd
Detect cable
Red Gnd
Green Gnd
Blue Gnd
PIN NO.
9.
10.
11.
12.
13.
14.
15.
DESCRIPTION
+5V/Sense(+5V)
Monitor Gnd
Logic Gnd
DDC serial data
H sync
V sync
DDC serial Clk.
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
TMDS Data 2TMDS Data 2+
TMDS Data 2/4 Shield
TMDS Data 4TMDS Data 4+
DDC Clock
DDC Data
N.C.
TMDS Data 1TMDS Data 1+
TMDS Data 1/3 Shield
TMDS Data 3-
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
20
DESCRIPTION
TMDS Data 3+
+5V Power
Ground(for+5V)
Hot Plug Detect
TMDS Data 0TMDS Data 0+
TMDS Data 0/5 Shield
TMDS Data 5TMDS Data 5+
TMDS Clock Shield
TMDS Clock +
TMDS Clock -
Download PDF