EL-150R DMX
USER MANUAL
Please read this manual carefully before use!
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 2 of 8
Table of contents
Page
1. SAFETY INSTRUCTIONS
3
2. OPERATING DETERMINATIONS
4
3. AUTO- MUSIC-MODE
5
4. OPERATION WITH DMX
5
5. DMX CHANNELS
6
6. MAINTENANCE
6
7. TECHNICAL SPECIFICATIONS
7
Checking Parts
Please check if the following parts are included:
1 x EL-150R DMX Laser
1 x Power cable
1 x User manual
Date 01/2008
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 3 of 8
DANGER LASER RADIATION!
Avoid direct eye exposure!
Laser radiation can cause eye damage and/or skin damage
All protective measures for a safe operation of this laser must be applied.
1. SAFETY INSTRUCTIONS
-
If the device has been exposed to drastic temperature fluctuation, do not
switch it on immediately. The arising condensation water might damage your
device. Leave the device switched off until it has reached room temperature.
1. The laser must only be used for shows. The operation is only allowed if it is
controlled by a skilled and well-trained operator.
-
Never leave this device running unattended and keep it away from children
and unauthorized persons.
2. Keep away from heaters and other heating sources. In order to safeguard
sufficient ventilation, leave 50 cm of free space around the device.
3. Never direct the laser beam to people or animals.
4. CAUTION LASER DIODE: Never unscrew the housing!
There are no serviceable parts inside the device. Maintenance and service
operations shall only be carried out by authorized dealers.
5. Always disconnect from the mains when the device is not in use or before
cleaning it.
-
HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!
Date 01/2008
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 4 of 8
2. OPERATING DETERMINATIONS
6. The operator has to make sure that laser radiation – also reflected laser
radiation –higher than the highest allowed level is avoided by technical or
organisational measures.
7. Make sure that the used voltage is : AC 220V~240V, 50/60Hz
8. If the device is used in a flying installation, the mounting brackets and an
appropriate safety-rope must be fixed.
9. Laser effects are not designed for permanent operation. Consistent operation
breaks will ensure that the device will serve you for a long time without
defects.
10. In some countries, the operator must notify the accidence insurance and the
authority for industrial safety, before operating a laser. For more information,
contact the relevant authorities.
11. Please consider that unauthorized modifications on the device are forbidden
due to safety reasons!
12. If this device will be operated in any way differently than described in this
manual, the product may suffer damages and the guarantee becomes void.
Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock, etc.
Date 01/2008
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 5 of 8
3. AUTO- MUSIC-MODE
When no DMX signal is connected (stand-alone mode) you can select auto mode
(patterns will be displayed one after the other), by setting switch 10 to “ON” before
turning the device on.
If you put switch 10 to “OFF” the patterns will change triggered by sound (sound or
music mode). You can control the music-sensitivity of the microphone with the minmax knob on the rear panel.
When DMX is connected you can also select these two modes alternatively to DMX
controlled operation (see chapter 5).
4. OPERATION WITH DMX
Set the DMX address code with the binary system “0” or “1”.
Examples:
DMX-
DMX-
Adress
adress
1
65
17
113
33
161
The device has 7 operate channels, so if you set the first on DMX address “1”
The second should be DMX address “8” and so on.
Date 01/2008
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 6 of 8
5. DMX CHANNELS
The DMX channels are set as follows:
Channel
Value
0 – 63
Function
Sound Mode
64 – 127
DMX Mode
128 – 191
Automatic mode (see chapter 3)
192 – 255
Blanking
2
0 - 255
Pattern
3
0 - 255
Dot Speed
4
0 - 255
Line Speed
5
0 – 255
X location
6
0 - 255
Y location
7
0 -255
Size
1
Please note that according to the pattern, not all effect channels are
activated. E.g. dynamic patterns can not be moved, vertical line can not be
moved in y, single dot can not be changed in size/dot speed, etc.
6. MAINTENANCE
Maintenance should be performed every 15-day period, by using a sponge dipped
with alcohol, rather than wet cloth or other chemical liquid, to clean the mirror.
Always disconnect from the mains when the device is not in use or before cleaning it.
There are no serviceable parts inside the device. Maintenance and service operations
are only to be carried out by authorized dealers.
Never look directly into the light source.
Always disconnect from the mains when the device is not in use or before
cleaning it.
Date 01/2008
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 7 of 8
7. TECHNICAL SPECIFICATIONS
Power supply: AC 220V-240V, 50/60 Hz
Power consumption: 40 W
Ambient temperature: -10°C – +35°C
Working mode: automatic, music active, DMX512
DMX 512: 7 channels
laser power: green: ca. 150mW / 650nm
Laser class: 3b
Weight: 3 kg
Dimensions: 25 x 28 x 10 cm
PLEASE NOTE
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and
unskilled operation!
Date 01/2008
USER MANUAL: Laserworld Ecoline EL-150R DMX
page 8 of 8
EU- Declaration of Conformity
We hereby confirm that the following device
Laserworld Ecoline EL-150R DMX
complies with the essential safety requirements, laid down in the regulations of the
committee to assimilate the provisions of law of all participating EU states on the
electromagnetic compatibility (98/336/EWG).
The device has been classified considering the following EU-norms on
electromagnetic compatibility:
DIN
DIN
DIN
DIN
EN
EN
EN
EN
55103-1: 1996
55103-2: 1996
61000-3-2:2000 + A2: 2005
61000-3-3:1995 + A1: 2001
Assessment of compliance of the product with the requirements relating to the Low Voltage
Directive (LVD) was based on the following standards:
DIN EN 60065 : 2002
Furthermore, the device is verified in correspondence to the laser class regulations DIN EN
60825-1, if properly set up according to the upper mentioned laser safety regulation.
After installing the device, an inspection and official approval is indispensable for the overall
setup. The inspection must follow the european guidelines EN 60825-1 and corresponding
regulations for the prevention of accidents BGV-B2.
This declaration is executed on behalf of the EL-150R DMX Laser manufacturer.
Laserworld (Switzerland) AG
Oberstrasse 1
8274 Tägerwilen
SWITZERLAND
Authorized person:
Supervisory board Ms Rhea Gössel
place of business: 8274 Tägerwilen / SWITZERLAND
company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
www.laserworld.com
info@laserworld.com
representative according to EMVG:
Cleantech Europe GmbH
Managing Director: Thomas Schulze
Fürkhofstr. 5
81927 München / DE
Date 01/2008
Download PDF