Veritas User Guide
Quick Reference Guide
THANK YOU FOR VOTING TEXECOM
THANK YOU FOR VOTING TEXECOM
MASTER USER GUIDE
Security Control Panels
Issue 4
1
INS167
Overview
Premier Series Master User Guide
Contents
1. Overview ....................................................................................................4
Introduction ................................................................................................................ 4
Keypads ...................................................................................................................... 6
Emergency Keys.........................................................................................................7
The Quick Arm Keys ...................................................................................................8
Keypad Lock ...............................................................................................................8
Reset and Service Messages .................................................................................... 8
Fault Messages...........................................................................................................9
Zone Faults During Arming...................................................................................... 10
2. Using the Alarm System .........................................................................11
Introduction .............................................................................................................. 11
3. Operating the Alarm System ..................................................................13
Introduction .............................................................................................................. 13
To FULL Arm the System ......................................................................................... 14
To PART Arm the System......................................................................................... 15
To ARM Individual Areas ......................................................................................... 16
To DISARM the System............................................................................................ 17
During Entry..............................................................................................................17
When Not in Entry.....................................................................................................17
To CANCEL the Exit Mode ....................................................................................... 18
To CLEAR an Arm Fail.............................................................................................. 18
To SILENCE an Alarm .............................................................................................. 19
To RESET After an Alarm ......................................................................................... 19
USER Reset ..............................................................................................................19
ENGINEER Reset......................................................................................................20
ANTI-CODE Reset.....................................................................................................20
To OMIT Zones ......................................................................................................... 21
To Turn CHIME On and Off...................................................................................... 22
To VIEW the Status of Zones ................................................................................... 23
To OMIT 24 Hour Zones ........................................................................................... 24
To SELECT Areas for Chime.................................................................................... 25
To VIEW Activity Faults ............................................................................................ 26
To VIEW Activity Counts .......................................................................................... 27
Sending a Text Message to a Mobile Phone .......................................................... 28
2
INS177
Premier Series Master User Guide
Overview
4. Programming the Alarm System............................................................29
Introduction .............................................................................................................. 29
Viewing the Event Log.............................................................................................. 30
Event Log Descriptions ............................................................................................31
Changing Your User Code ....................................................................................... 33
Setting up Zones for Chime..................................................................................... 34
Testing the Sounders and Strobe ........................................................................... 35
Walk Testing the System ......................................................................................... 36
Enabling Engineer Access....................................................................................... 37
Setting the System Time .......................................................................................... 38
Setting the System Date........................................................................................... 39
Overriding the Control Timers................................................................................. 40
Altering the Control Timers ..................................................................................... 41
Adding New Users to the System............................................................................ 43
Programming New Users .........................................................................................43
User Types................................................................................................................44
Available Options......................................................................................................45
User Options 1..........................................................................................................46
User Options 2..........................................................................................................47
User Config. ..............................................................................................................48
User Name Text ........................................................................................................49
Programming Users .................................................................................................50
Deleting Users ..........................................................................................................52
Setting up the Part Arms.......................................................................................... 53
Calling a Remote PC ................................................................................................ 54
Altering the Holiday Dates ....................................................................................... 55
Adjusting Speaker Volumes .................................................................................... 56
Printing the Event Log.............................................................................................. 57
Editing a Mobile Telephone Number....................................................................... 58
5. Specifications..........................................................................................59
European Standards ................................................................................................ 59
Warranty.................................................................................................................... 59
6. Installation Records................................................................................60
INS177
3
Overview
Premier Series Master User Guide
1. Overview
Introduction
The alarm system consists of a control panel, one or more keypads and various detectors
and sensors. The control panel is normally mounted out of sight in a cupboard etc. and
houses the system’s electronics and stand-by battery. There is normally no reason for
anyone except an installer or service person to have access to the control panel.
The keypad is used to control the alarm system and to display its status via the English
text display. The keypad also provides audible feedback each time a key is pressed.
Each keypad will be mounted in a convenient location inside the protected premises,
near the designated points of entry/exit.
Users
Users of the alarm system will be assigned a unique 4, 5 or 6 digit User code. User
codes are used to arm and disarm areas to which they are assigned. Some User codes
can also access additional options such as, system tests and omitting zones.
To access the system a valid User code must be entered, if a mistake is made whilst entering
a User code, simply re-enter the correct code (the system may have been programmed so
that too many incorrect code entries will cause a Tamper alarm or lock the keypad out).
The User code may not allow access to certain functions i.e. if the code is only allowed
to arm and disarm area A, it will not be able to arm or disarm other areas on the system.
Most User codes can arm and disarm areas assigned to them from any keypad on the
system. However, Local Users will only be able to arm and disarm areas assigned to them,
from keypads assigned to the same areas.
As well as or instead of a code, users of the alarm system can be assigned a Proximity
TAG. Proximity TAGS replace the code number being entered with a key ring type TAG
that is presented to the reader inside the keypad to operate the alarm system.
Zones
A ‘zone’ is part of the protected premises and may consist of one or more detection
devices protecting rooms and points of entry/exit, (e.g. front door, kitchen, downstairs
windows, upstairs bedrooms, etc.). When the alarm system is fully armed, all of the
zones on the system are monitored.
Some zones may belong to more than one area, such as points of entry/exit i.e. the front
door and movement sensor in an entrance lobby. These are called global zones
because they are assigned to multiple areas.
A zone that is assigned to more than one area will only be monitored when all of the
areas it is assigned to are armed.
4
INS177
Premier Series Master User Guide
Overview
Areas
An ‘area’ is a group of one or more zones and would normally be used to split the
premises into different sections. Each area can be either ‘Full’ armed or ‘Part’ armed.
Example 1: Domestic Premises
The entire house could be area A.
Each area can be ‘Part’ armed. For instance, detection devices upstairs, i.e. PIR’s, could
be programmed so that they will not be monitored during a ‘Part’ arm, allowing access to
the upstairs of the house at night.
!"
Area A forms the entire alarm system.
Example 2: Domestic Premises
The upstairs of a house could be area A, the downstairs could be area B and the garage
could be area C.
Each area can be ‘Full’ armed independently from each other (all detection devices in
the area monitored). For instance, downstairs and the garage in example 1 (areas B & C)
could be armed at night allowing access to the upstairs of the house (area A).
!"
All of the areas together form the entire alarm system.
Example 3: Commercial Premises
Office 1 in an office block could be area A, office 2 could be area B and office 3 could be
area C.
Each area can be armed and disarmed independently from each other. For instance, any
of the offices in example 2 above could be armed and disarmed to allow access without
affecting the other offices.
!"
All of the areas together form the entire alarm system.
Example 4: Office Block
The foyer of the office block in example 4 would need to be armed when the last office is
armed and disarmed when the first office is disarmed.
Because the foyer is a global area (used by everyone) the zones in that area need to be
assigned to areas A, B and C. This ensures that the zone is only recognised by the
system when ALL areas (A, B & C) are armed, allowing access to the foyer even if one of
the areas is still armed.
Monitoring
This alarm system is capable of reporting Intruder alarms, Panic alarms, Fire alarms and
other types of information over telephone lines to an Alarm Receiving Centre. If you
accidentally set the alarm off, call the Alarm Receiving Centre immediately to prevent an
unnecessary response.
!"
The monitoring function must be enabled before it will work.
INS177
5
Premier Series Master User Guide
Overview
Keypads
One or more keypads will be installed throughout the protected premises, usually one at
each entry/exit door. The keypads are used to perform all of the system functions i.e.
Arming, Disarming etc.
Premier LCDL/LCDLP
Large Display
Premier LCD/LCDP
Standard Display
Power
Screen Not Shown
Proximity Reader
(LCDP & LCDLP
keypads only)
Programmable
‘Info.’ LED
Ready
Omit
Service
2 abc
3 def
Omit
4 ghi
5
jkl
6 mno
Chime
7 pqrs
8 tuv
9 wxyz
Part
Yes
0 _
No
Area
1
Normal
Keys
Info.
Reset
Function
Keys
Menu
Display Window (Premier LCD/LCDP & LCDL/LCDLP)
The 32-Character LCD display is used to show the status of the system and to view
system data.
Proximity Reader (Premier LCDP & LCDLP only)
Built in Proximity Reader for use with Proximity TAGS (approximate range is between
1 and 5 cm). Proximity TAGS can be used as an alternative to a Code number.
LED Indicators
Five LED indicators have been provided to indicate the status of the system.
LED
Power
Status
On
Flashing
Service
Ready
AC mains is present on the control panel
AC Mains is not present, the control panel is running on the standby battery
On
The system requires attention, contact your installer
Off
The system does NOT require attention
On
All zones are secure and the system is ready to be armed
Off
One or more zones are active
Flashing
6
Meaning
The system has zones (with the ‘Force Omit’ attribute) that are active
Info.
On
The system is armed (can also be programmed for other indications)
Off
The system is unarmed (can also be programmed for other indications)
Omit
On
One or more zones are omitted
Off
No zones are omitted
INS177
Premier Series Master User Guide
Overview
Keys
Keys ! to "
These keys are for entering User codes or programming data.
Yes & No Keys # & $
The YES key is used to accept actions and the NO key is to cancel actions or edit data.
Omit Key %
This key is used to omit zones (see page 21 for details).
Chime Key &
This key is used for turning the chime facility on and off (see page 22 for details) and
also for turning the Exit tones on and off during the exit mode.
Part Key '
This key is used to part arm the system (see page 15 for details). It can also be used to
do a ‘Quick’ part arm if this feature is enabled.
Area Key (
This key is used to arm or disarm particular areas (see page 16 for details). It can also be
used to do a ‘Quick’ arm if this feature is enabled.
Reset Key )
This key is used to exit from a menu or to reset the system (see page 19 for details).
Scroll Key *
This key is used to scroll through the various menus and options and also to slow down
the display if it is scrolling through alarm information too fast.
Menu Key +
This key is used to select the Arming or User menu.
Emergency Keys
In case of emergency, the alarm system can provide three immediate emergency alarms
by pressing and holding two specific keys.
Press Keys
UK Response
Export Response
!&,
-&.
/&"
Panic Alarm (PA)
Fire
Fire
Panic Alarm (PA)
Medical
Medical
!"
The emergency keys can be enabled/disabled for each keypad on the system.
The Panic alarm can be programmed for either audible or silent operation.
The Panic alarm can be programmed for either instant or delayed operation.
INS177
7
Premier Series Master User Guide
Overview
The Quick Arm Keys
The ‘Quick Arm’ keys allow the system to be armed without having to enter a User code first.
!"
The ‘Quick Arm’ keys will only work if the keypad has been programmed to allow
arming in this way.
To FULL arm the system, press (.
To PART arm the system, press !, 0 or , followed by '.
Keypad Lock
The keys on the keypad can be locked to prevent unwanted access to the system.
!"
The Emergency keys will NOT operate with the keys locked.
To Lock the keys, press # and $ together.
To Unlock the keys, press # and $ together again.
Reset and Service Messages
When the system requires a reset/service the display will show one of three messages.
These messages can also be accessed at any time from the normal display.
!"
These messages may have been programmed with the telephone numbers of the
installer or the Alarm Receiving Centre.
When alarm information is being displayed, pressing the SCROLL key will slow
down the display and also allow manual scrolling through the events.
To display the reset/service messages, proceed as follows:
Press + followed by ! to view the Service message
!"##$%#"&'$!()
$$*(&$+,&-./,
Press + followed by 0 to view the Reset message
!"##$012.1,,&$3(
$$4,5,3$+653,'
Press + followed by , to view the Anti-code message
!"##$%4!$3(
4,5,3$+653,'
Press ) to exit from the messages
The display will return to normal.
8
INS177
Premier Series Master User Guide
Overview
Fault Messages
7".15$8(9,&$:;;
$<=,$>?$7"&$@>>A
There is a Mains failure (the keypad may chime every minute, enter a valid
User code or press
to stop the chime). The display will automatically
clear when mains is reapplied.
8B(1,$C.1,$*"=#3
$<=,$>?$7"&$@>>A
There is a Phone Line fault (the keypad may chime every minute, enter a
valid User code or press
to stop the chime). The display will
automatically clear when line fault clears.
D"33,&6$*"=#3
$<=,$>?$7"&$@>>A
There is a fault with the standby battery (the keypad may chime every
minute, enter a valid User code or press
to stop the chime). Contact
your alarm company immediately.
EEEEEEEE$<"'F,&
$<=,$>?$7"&$@>>A
+,&-./,$4,G=.&,H
$<=,$>?$7"&$@>>A
I$%&,"$+,/=&,H$I
$<=,$>?$7"&$@>>A
$%/3.-.36$*"=#3
$<=,$>?$7"&$@>>A
)
)
)
There is a Tamper fault (the alarm will sound, enter a valid User code to
silence the alarm, this fault cannot normally be cleared). Contact your alarm
company immediately.
The service timer has expired indicating that the system requires a service
or a fault has occurred that requires attention (the system can normally still
be used). Contact your alarm company to advise.
The keypad has been disabled to prevent unauthorised access. This
normally occurs when a zone programmed as ‘Security Key’ is active, the
display will automatically clear when the zone returns to normal.
A zone with the ‘Activity’ attribute has not been activated within the activity time
period, this may be caused by an obstruction (view the zone status to find out
which zone has not activated then activate the zone to clear the fault).
EEEE$*=5,$D#(91
$<=,$>?$7"&$@>>A
A fuse has blown (the alarm will sound, enter a valid User code to silence the
alarm, this fault cannot be cleared). Contact your alarm company immediately.
%&,"$*".#,H$<,53
$<=,$>?$7"&$@>>A
Zones that have been placed on test by the engineer have failed the test
(the system can still be used). Contact your alarm company to advise.
4,'(3,$J,6F"H$.5
1(9$C:!J0K$(=3
Too many invalid code attempts have caused the keypad to lock out. The
keypad will normally remain like this for 5 minutes.
<.',$%&'.12$L
$$$$%)))))))
Areas are being armed using one of the control timers (enter a valid User
code to defer the arming).
%#"&'$012.1,,&
M(&N.12$:1$+.3,
The alarm engineer has logged into the programming menu and is working on
site (this message will clear when the engineer logs off or the system is armed).
!"
When alarm information is being displayed, pressing the SCROLL key will slow
down the display and also allow manual scrolling through the events.
INS177
9
Premier Series Master User Guide
Overview
Zone Faults During Arming
Before attempting to arm the system, ensure that the premises are secure (all doors and
windows closed etc.) and the Ready light is on.
If an attempt is made to arm the system with any zones active (e.g. door ajar, open
window, etc.) the internal sounders will bleep repeatedly (fault tone) and the display will
show the zones that are active.
O(1,$>>A$%/3.-,
*&(13$H((&
The fault tone will stop and the exit tone will resume when all zones are secure. If it is
necessary to leave a zone open then it must be omitted (see page 21 for details).
!"
If an active zone cannot be secured then it may be ‘in fault’ in this case contact the
alarm company immediately.
Arm Fail - Failing to Arm
If the exit procedure is started and zones are still ‘Active’ at the end of the exit procedure,
an Internal alarm will occur (internal sounders only) and the strobe light on the external
sounder will flash.
!"
If this occurs the arm fail must be cleared and the zone in fault identified before the
system can be armed (see page 18 for details on clearing an Arm Fail).
The Ready LED
To help prevent faults during arming, a Ready light has been provided. The Ready light
works as follows:
•
If the Ready light is ON then all zones are secure and the system is ready to be armed
•
If the Ready light is OFF then one or more zones are active, either secure or omit
these zones before proceeding
•
If the Ready light is FLASHING then the system has zones (with the ‘Force Omit’
attribute) that are active, check these zones before proceeding.
10
INS177
Premier Series Master User Guide
Using The Alarm System
2. Using the Alarm System
Introduction
The operation of the system is divided up into two sections, the Arming menu and the
User menu.
To access the Arming menu enter a valid User code 1111. Once in the
Arming menu, various functions can be selected by using the * key. Once a function
has been selected press # to access that function.
To access the User menu press + followed by #. Once in the User menu, various
options can be selected by using the * key. Once an option has been selected press
# to access that option.
To exit from either menu press the ) key and the display will return to normal.
The diagram on page 12, shows both menus and the functions and options available.
!"
The range of available functions and options will depend on the control panel
being used (some control panels do not support all of the features) and also the
type of user on that system. If a function or option cannot be selected, it may be
that it is not assigned to that user (see page 45 for details).
To access the Arming/User menu, proceed as follows:
The display will normally show the time & date (The top line is programmable).
$$
$<=,$>?$7"&$@>>A
To access the Arming menu enter a valid User code 11112
K($6(=$9"13$3(
%&'$+653,'E
To select the User menu Press +2
K($6(=$9"13
P5,&$7,1=E
To access the User menu Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press ) to exit either menu
The display will return to normal.
INS177
11
Premier Series Master User Guide
Using The Alarm System
The Arming Menu
The User Menu
$$
A>R@S)TT"$M,H$>A
K($6(=$9"13
P5,&$7,1=$E
Yes
Enter A Valid User Code
1
K($6(=$9"13$3(
%&'$+653,'E
1
K($6(=$9"13$3(
Q.,9$0-,13$#(2E
2
abc
K($6(=$9"13$3(
8"&3$%&'$+653,'E
2 abc
K($6(=$9"13$3(
!B"12,$!(H,E
3
def
K($6(=$9"13$3(
+.#,13$%&'E
3 def
K($6(=$9"13$3(
0H.3$!B.',$O(1,5E
4 ghi
K($6(=$9"13$3(
!"1/,#$0W.3E
4 ghi
K($6(=$9"13$3(
K($+653,'$3,535E
5 jkl
K($6(=$9"13$3(
K.5"&'$+653,'E
5 jkl
K($6(=$9"13$3(
K($M"#N$<,53E
6 mno
K($6(=$9"13$3(
P5,$%13.V/(H,E
6 mno
K($6(=$9"13$3(
01"X#,$012.1,,&E
7 pqrs
K($6(=$9"13$3(
:'.3$O(1,5E
7 pqrs
K($6(=$9"13$3(
+,3$+653,'$<.',E
8 tuv
K($6(=$9"13$3(
Q.,9$O(1,$+3"3=5
8 tuv
K($6(=$9"13$3(
+,3$+653,'$K"3,E
9 wxyz
K($6(=$9"13$3(
:'.3$@SU&$O(1,5E
9 wxyz
K($6(=$9"13$3(
:-,&&.H,$<.',&5E
0_
K($6(=$9"13$3(
+,3$!B.',$%&,"5E
K($6(=$9"13$3(
%#3,&$<.',&5E
K($6(=$9"13$3(
Q.,9$%/3)$*"=#35
K($6(=$9"13$3(
+,3=F$P5,&5E
K($6(=$9"13$3(
Q.,9$%/3)$*"=#35
K($6(=$9"13$3(
0W.3$7,1=E
%#3,&$8"&3$%&'5E
K($6(=$9"13$3(
+,1H$+7+$<,W3$E
K($6(=$9"13$3(
!"##$4,'(3,$8!E
K($6(=$9"13$3(
0W.3$7,1=E
K($6(=$9"13$3(
0W.3$7,1=E
%#3,&$U(#)$K"3,5
Menu
K($6(=$9"13
P5,&$7,1=$E
Reset
$$$
A>R@S)TT"$M,H$>A
K($6(=$9"13$3(
%HY=53$Q(#=',5E
Yes
K($6(=$9"13$3(
8&.13$0-,13$C(2E
K($6(=$9"13$3(
0H.3$8B(1,$Z()E
0_
Reset
12
K($6(=$9"13$3(
0W.3$7,1=E
$$
A>R@S)TT"$M,H$>A
INS177
Premier Series Master User Guide
Operating the Alarm System
3. Operating the Alarm System
Introduction
The normal day-to-day operations of the system are carried out using the Arming menu
i.e. arming, disarming, omitting zones etc.
!"
The range of available functions and options will depend on the control panel
being used (some control panels do not support all of the features) and also the
type of user on that system.
Not all functions are available to all users. If a function cannot be selected, it may be
that it is not assigned to that user (see page 45 for details).
If no keys are pressed, the display will return to normal after a pre-programmed time.
The table below shows the various functions available:
Arming Menu
Key
3
!
0
,
4
.
/
5
"
*
*
*
+
INS177
Function
Page
Arm System"
14
Part Arm System"
15
Silent Arming"
14
Cancel Exit"
18
Disarm the System"
17
Use Anti-code"
20
Omit Zones"
21
View Zone Status"
23
Omit 24Hr Zones"
24
Set Chime Areas"
25
View Act. Faults"
26
View Act. Counts"
27
Send SMS Text"
28
User Menu"
29
13
Premier Series Master User Guide
Operating the Alarm System
To FULL Arm the System
The system is FULL Armed when ALL zones are ON (not omitted).
!"
(
Your Installer may have programmed the system so that it can be set by just pressing
, if this is the case then there is no need to enter the User code below.
To arm the system, proceed as follows:
Ensure that the premises are secure (all doors and windows
closed etc.) and the Ready light is on.
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press 0 to Silent arm (if required)
K($6(=$9"13$3(
+.#,13$%&'E
Press # to arm
The exit tone will sound (if silent arm has not been selected)
%&,"5$.1$0W.3$L
$$$$%)))))))$
Leave the premises
When the system has armed the exit tone will stop (if sounding)
$$$$
$<=,$>?$7"&$@>>A
The system is now armed.
14
INS177
Premier Series User Guide
Operating the Alarm System
To PART Arm the System
The system is PART Armed, when ONE OR MORE zones have been left OFF (omitted)
i.e. the landing or a bedroom.
!"
The system is only Part Armed when zones are omitted using the ‘Part Arm’ procedure
(omitting zones manually (see page 21 for details) is not classed as Part Arming).
The bottom line of the display is programmable for each Part Arm.
Your Installer may have programmed the system so that it can be part armed by
just pressing !, 0 or , followed by ' if this is the case then there is
no need to enter the User code below.
To part arm the system, proceed as follows:
Ensure that the premises are secure (all windows and doors not
being omitted are closed) and the Ready light is on.
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press '
K($6(=$9"13RV
0-,1.12$"&'
Use keys ! - , to select the required part arm
K($6(=$9"13RV
D,H3.',$"&'
Press # to arm normally or press & to arm silently
The exit tone will sound (if silent arm has not been selected)
%&,"5$.1$0W.3$L
$$$$%)))))))$
Leave the protected area
When the system has armed, the exit tone (if sounding) will stop
D,H3.',$"&'
$$$$%)))))))
I$$8%4<$%470K$$I
$<=,$>?$7"&$@>>A
The system is now part armed.
INS177
15
Premier Series User Guide
Operating the Alarm System
To ARM Individual Areas
If the system has been split up into separate areas of protection i.e. Area 1 = House,
Area 2 = Garage, Area 3 = Shed etc. These areas can be individually selected for FULL
or PART arming as required.
!"
Areas are selected by using keys ! - 5 (the
select an area followed by ( or $).
* key can also be used to
Only areas that exist on the system can be selected. (a star means the area can be
selected and a dot means the area cannot be selected).
Pressing 3 will select/deselect all areas, pressing ( will toggle between the
first 8 areas and the second 8 areas (where applicable).
To select areas for arming, proceed as follows:
Ensure that the premises are secure (all windows and doors not
being omitted are closed) and the Ready light is on.
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press (
+,#,/3$%&,"5$L
$$L$III)))))$[
Use keys ! - 5 to select the required area
+,#,/3$%&,"5$L
$$L$%DIIII))$[
Press # or & to FULL arm
Or
Press '!, 0 or , followed by # or & to PART arm
The exit tone will sound (if silent arm has not been selected)
%&,"5$.1$0W.3$L
$$$$%D))))))$
Leave the premises
When the areas have armed, the exit tone (if sounding) will stop
%&,"5$%&',H$L
$$$$%D))))))
The selected areas are now armed.
16
INS177
Premier Series User Guide
Operating the Alarm System
To DISARM the System
The Entry time is divided into two sections, the Entry time and the 2nd Entry time. If the
Entry time expires, an Internal alarm will occur and the 2nd Entry time will start. If the 2nd
Entry time expires, an Intruder alarm will occur (all internal and external sounders).
!"
It is perfectly normal for the 2nd Entry time to be programmed as zero, in which
case, an Intruder alarm will occur as soon as the Entry time expires.
During Entry
To disarm the system, proceed as follows:
Enter the premises via the designated entry point
The entry tone will start
%&,"5$.1$013&6$L
$$$$%D!)))))$
Enter a valid User code 1111
The entry tone will stop
$$
$<=,$>?$7"&$@>>A
The system is now disarmed.
When Not in Entry
To disarm the system, proceed as follows:
The display will look something like this:
$$
$<=,$>?$7"&$@>>A
Enter a valid User code 1111
K($6(=$9"13$3(
K.5"&'$+653,'E
Press #
$$
$<=,$>?$7"&$@>>A
The system is now disarmed.
INS177
17
Premier Series User Guide
Operating the Alarm System
To CANCEL the Exit Mode
Once the exit mode has been started you should leave the premise immediately, however,
if for some reason you decide not to leave, the exit mode must be cancelled.
To cancel the exit mode, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
!"1/,#$0W.3E
Press #
The exit tone will stop
$$
$<=,$>?$7"&$@>>A
The exit mode has now been cancelled.
To CLEAR an Arm Fail
When the system tries to arm with zones active (open), the internal sounders will sound
and the external strobe will be flashing to indicate a problem. For details on preventing
an Arm Fail condition, please refer to page 10.
!"
If you were not present when the arm fail occurred or you do not clear the arm fail, the
internal sounders will continue to sound and the external strobe will continue to flash.
To clear the arm fail, proceed as follows:
The alarm will be sounding and the display will look something like this:
%&,"$%47$*%\C$L
$$$$%)))))))
Enter a valid User code 1111
The internal and external sounders will stop, the external strobe will continue to flash and
the number of the zone that caused the arm fail will be displayed (in this case Zone 2).
%&,"$%47$*%\C$L
$$$$%)))))))
O(1,$>>@$%/3.-,
D,H&(('$M.1H(9
Enter a valid User code 1111 and press )
$$
$<=,$>?$7"&$@>>A
The arm fail has now been cleared.
18
INS177
Premier Series User Guide
Operating the Alarm System
To SILENCE an Alarm
When an alarm occurs on the system, the internal and external sounders will normally
sound for a pre-programmed time (normally 15 minutes).
!"
If you were not present when the alarm activated, the internal and external
sounders may have already stopped but the external strobe will still be flashing.
When alarm information is being displayed, pressing the SCROLL key will slow
down the display and also allow manual scrolling through the events.
To silence an alarm, proceed as follows:
The alarm will be sounding and the display will look something like this:
$$
$<=,$>?$7"&$@>>A
Enter a valid User code 1111
The internal and external sounders will stop and the number of the zone
that caused the alarm will be displayed (in this case Zone 2)
O(1,$>>@$%#"&'
ASRS?)>SF$<=,$>?
<B,$U"##9"6$8.&
The alarm now needs to be reset.
To RESET After an Alarm
USER Reset
Once the alarm has been silenced (see above), the system will need to be reset.
!"
If the system has been programmed to be reset by an Engineer, pressing ) will not
return the display to normal, if this is the case see ENGINEER Reset (page 20) for details.
The system may have been programmed to be reset by Anti-code, if this is the
case, see ANTI-CODE Reset (page 20) for details.
To reset the alarm, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press )
The external strobe will stop, the system will chime
and the display will return to normal.
INS177
19
Premier Series User Guide
Operating the Alarm System
ENGINEER Reset
If the system has been programmed to be reset by an Engineer following an alarm
activation, you will still be able to silence the alarm by entering a valid User code (see
page 19 for details).
!"
The system cannot be armed again until the alarm has been reset.
To reset the alarm, proceed as follows:
Contact the telephone number on the display (if programmed) or
the telephone number on the last page of this User Guide.
ANTI-CODE Reset
If the system has been programmed to be reset using an Anti-Code following an alarm
activation, you will still be able to silence the alarm by entering a valid User code (see
page 19 for details).
!"
The system cannot be armed again until the alarm has been reset.
To reset the alarm, proceed as follows:
Enter a valid User code 1111
8&,55$40+0<$;(&
%13.V/(H,
Press )
The display will show a random code number i.e. 4281
]=(3,$L$S@^A
4,F#6$L$VVVV
Contact the telephone number on the display (if programmed) or the telephone
number on the last page of this User Guide and quote the random code number.
You will be given a 4-digit Anti-Code i.e. 5624
Enter the Anti-code that has been given to you 1111
]=(3,$L$S@^A
4,F#6$L$T?@S
Press #
If the Anti-code is correct, the keypad will chime to indicate that the system
has been reset and the display will return to normal.
20
INS177
Premier Series User Guide
Operating the Alarm System
To OMIT Zones
It is possible to exclude (omit) individual zones when arming i.e. if a zone is ‘in fault’. Users
with access to this function can only omit zones that have been programmed as ‘Omittable’.
!"
If the zone can be omitted, there will be a star to the right of the zone number.
Only zones that have the ‘Omit’ attribute assigned to them can be omitted.
A star will appear to the left of the zone number to indicate that the zone has been
selected for omitting.
All omitted zones will be automatically reinstated the next time the system is
disarmed, unless programmed otherwise.
To re-instate zones manually, simply follow the instructions again. However, when
the % key is pressed this time, the zones will be re-instated.
To omit zones when arming, proceed as follows:
Enter a valid User code 1111 and press %
O(1,$>>AI+,/=&,
*&(13$K((&$$$$$L
Enter a zone number 111 or use the * key to search
O(1,$>A>I%/3.-,
C(=12,$K,3,/3(&$L
Press % to omit the selected zone
O(1,I>A>I%/3.-,
.5$:'.33,H
O(1,I>A>I+,/=&,
C(=12,$K,3/3(&$L
Repeat for other zones if required
Press + when finished
K($6(=$9"13$3(
%&'$+653,'E
Continue to arm the system as normal
The selected zones are now omitted (the omit light will be on).
INS177
21
Premier Series User Guide
Operating the Alarm System
To Turn CHIME On and Off
The system can be set up so that activating (opening) certain zones will cause the
internal sounders to chime. This would normally be used on a front door, exit button etc.
!"
Zones will only cause the internal sounders to chime if they are selected for chime
(see page 34 for details on selecting which zones chime).
Once a zone has been selected for chime, the Chime facility can be manually turned on
and off as required.
!"
The system can also be programmed to automatically turn Chime on and off
under certain conditions i.e. certain times of the day, door left open etc.
If no zones have been programmed for chime, then turning Chime on and off will
have no effect.
To turn CHIME On proceed as follows:
Press &
The Chime tone will sound.
To turn CHIME Off proceed as follows:
Press &
The Fault tone will sound.
22
INS177
Premier Series User Guide
Operating the Alarm System
To VIEW the Status of Zones
Users with access to this feature will be able to check the status of each zone on the
system to see whether it is in ‘Fault’, ‘Secure’, ‘Tamper’, ‘Shorted’ or ‘Inactive’.
To view the status of zones, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press 5
K($6(=$9"13$3(
Q.,9$O(1,$+3"3=5
Press #
O(1,$>>A$+,/=&,
*&(13$K((&$$$$$L
Enter a zone number 111 or use the * key to search
O(1,$>A>$+,/=&,
C(=12,$K,3,/3(&$L
(Pressing & will make the zone chime every time it is activated (an Arrow will
appear to the right of the zone number), to clear the Chime, press & again)
(Pressing ( will display the zone text)
(Every time the selected zone is activated, its status will be
displayed and the keypad will chime, if selected)
O(1,$>A>L%/3.-,
C(=12,$K,3,/3(&$L
O(1,$>A>L+,/=&,
C(=12,$K,3,/3(&$L
Press + when finished
Press ) to exit the menu
The display will return to normal.
INS177
23
Premier Series User Guide
Operating the Alarm System
To OMIT 24 Hour Zones
It is possible to exclude (omit) or include 24 Hour zones whilst the system is disarmed to
allow access to an area. Users with access to this function can only omit zones that have
been programmed as ‘Omittable’.
!"
If the zone can be omitted, there will be a star to the right of the zone number.
Only zones that have the ‘Omit’ attribute assigned to them can be omitted.
A star will appear to the left of the zone number to indicate that the zone has been
selected for omitting.
To re-instate the zones, simply follow the instructions again. However, when the
% key is pressed on this occasion, the zones will be re-instated.
To omit 24 Hour zones, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press "
2
K($6(=$9"13$3(
:'.3$@SU&$O(1,5
Press #
O(1,$>>A$+,/=&,
*&(13$K((&$$$$$L
Enter a zone number 111 or use the * key to search
O(1,$>AT$+,/=&,
D"/N$K((&$$$$$$L
Press
% to omit the selected zone
O(1,I>AT$+,/=&,
.5$:'.33,H
O(1,I>AT$+,/=&,
D"/N$K((&$$$$$$L
Repeat for other zones
Press + when finished
Press ) to exit the menu
The display will look like this:
I$O(1,5$:'.33,H$I
$<=,$>?$7"&$@>>A
The selected 24 Hour zones are now omitted.
24
INS177
Premier Series User Guide
Operating the Alarm System
To SELECT Areas for Chime
When a zone is enabled for Chime the Keypad will generate a chime tone every time the
zone is activated. Users with access to this function will be able to turn Chime on and off
for selected areas.
Zones within an area can be individually programmed for Chime in Edit Chime Zones
(see page 34 for details).
!"
Only areas that have been programmed for ‘Chime’ can be selected. A star means
the area can be selected and a dot means the area cannot be selected.
Pressing 3 will select/deselect all areas.
Pressing ( will toggle between areas A to H and I to P (Premier 168 only).
To select an area for Chime, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press &
2
01"X#,$!B.',$(1
$$L$III)))))$[
Use keys ! - 5 to select/deselect areas
(i.e. !, 0 and , = Areas A, B and C)
01"X#,$!B.',$(1
$$L$%D!)))))$[
Press # when finished
Press ) to exit the menu
The display will return to normal.
INS177
25
Premier Series User Guide
Operating the Alarm System
To VIEW Activity Faults
If any zones with the ‘Activity’ attribute have not been activated within a certain time
period, an activity fault will be displayed at the time of arming. Users with access to this
function will be able to view the activity faults.
!"
To view activity faults on a Premier 24, the ‘View Zone Status’ menu must be used
(see page 23 for details).
The system may have been programmed so that an activity fault will not allow
arming. If this is the case the system can only be armed once the zone in fault has
been activated (forced walk test).
Only zones with the ‘Activity’ attribute that have not been activated will be shown.
To view activity faults, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press * until the display looks like this:
K($6(=$9"13$3(
Q.,9$%/3)$*"=#35
Press #
O(1,$>>A$+,/=&,
*&(13$K((&$$$$$L
Press * to scroll up and down through the zones
Press + when finished
Press ) to exit the menu
The display will return to normal.
26
INS177
Premier Series User Guide
Operating the Alarm System
To VIEW Activity Counts
Users with access to this menu will be able to view the number of times that zones with
the ‘Activity’ attribute have been activated, for each area.
To view activity counts, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press * until the display looks like this:
K($6(=$9"13$3(
Q.,9$%/3)$!(=135
Press #
%/3.-.36$%L$>>>>
<(3"#$!(=13$>>>T
Use keys ! - 5 to select an area or use the * key to search
(To reset the activity counter press ))
%/3.-.36$DL$>>>T
<(3"#$!(=13$>>>>
Press + when finished
Press ) to exit the menu
The display will return to normal.
INS177
27
Premier Series User Guide
Operating the Alarm System
Sending a Text Message to a Mobile Phone
If the control panel has a Com2400 or GSM Module fitted, the keypad can be used to send
a Text message directly to any of the pre-programmed mobile phone numbers.
To send a Text Message, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press * until the display looks like this:
K($6(=$9"13$3(
+,1H$+7+$<,W3$E
Press #
$
_$$$$$$$$$$$L<`<
Use the keypad to type a message, press # when finished
(For details on programming text please refer to page 49).
<,#,FB(1,$Z()$AL
>a^>A@bST?
Press * to select the required telephone number
<,#,FB(1,$Z()$bL
>a^c>A@bST?
Press # when finished
$$$$
$<=,$>?$7"&$@>>A
The display will return to normal.
28
INS177
Premier Series Master User Guide
Programming the Alarm System
4. Programming the Alarm System
Introduction
Advanced operations of the system are carried out using the User Menu i.e. System Tests,
Assigning Users etc.
!"
The range of available functions and options will depend on the control panel
being used (some control panels do not support all of the features) and also the
type of user on that system.
Not all options are available to all users. If an option cannot be selected, it may be
that it is not assigned to that user (see page 45 for details).
If no keys are pressed, the display will return to normal after a pre-programmed time.
The table below shows the various options available:
User Menu
Key
!
0
,
4
.
/
5
"
*
*
*
*
*
*
*
*
INS177
Option
View Event Log"
Page
30
Change Code"
33
Edit Chime Zones"
34
System Tests"
35
Walk Test"
36
Enable Engineer"
37
Set System Time"
38
Set System Date"
39
Override Timers"
40
Alter Timers"
41
Setup Users"
43
Alter Part Arms"
53
Call Remote PC"
54
Alter Hol. Dates"
55
Adjust Volumes"
56
Print Event Log"
57
Edit Phone No."
58
29
Premier Series User Guide
Operating the Alarm System
Viewing the Event Log
Users with access to this option can view the system Event Log. This log records all of
the events that occur on the system, i.e. Users entering their codes to arm or disarm the
system, alarms, failures to arm etc. along with the time and date on which they occurred.
!"
The down key moves you to the previous event (backwards in time), and the up
key moves you forwards again.
The ( key toggles between the area information and the time/date.
For a full list of Event Log descriptions, please refer to the Master User Guide.
To view the Event Log, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press #
!(H,$>A$K"-.H
$A@R@^)>S$>?d>b
Press * to scroll up and down through the Log
%&,"5$K.5"&',H
$A@R@^)>S$>?d>b
Press ( to toggle between the area information and the time/date
Press ' to display zone text (where applicable)
%&,"5$K.5"&',H
$$$$%)))))))
Press + when finished
Press ) to exit the menu
The display will return to normal.
30
INS177
Premier Series Master User Guide
Programming the Alarm System
Event Log Descriptions
Log Event
Description
KSW ### Active
A Keyswitch zone type has been activated (zone number ###)
RKP #,# MEDICAL
A Medical alarm (7 & 9) has occurred from keypad number #,#
RKP #,# FIRE
A Fire alarm (4 & 6) has occurred from keypad number #,#
RKP AUD PA #,#
An Audible PA alarm (1 & 3) has occurred from keypad number #,#
RKP SIL PA #,#
A Silent PA alarm (1 & 3) has occurred from keypad number #,#
DURESS
User ## has entered a Duress Code at a keypad
ALARM Active
An Intruder alarm signal has been activated for area ?
BELL Active
The Bell output has been activated for area ?
REARM LOCK ###
Zone ### has re-armed after causing an alarm
CROSS ###
A Verified Cross Zone Alarm has occurred from zone ###
USER ##
User ## has entered their code
AREAS EXIT
The Exit mode has been started for area ?
ARMING FAILED
A Exit Error-Arm Fail has occurred on area ?
AREAS ENTRY
The Entry mode has been started for area ?
ARMING SUITE
Area Arm Suite # was used to arm the system
ARMED WITH L/F
The system has been armed with a Line Fault condition present
AREA Armed
Area ? has been armed
AREA Disarmed
Area ? has been disarmed
PART Armed
Area ? has been Part Armed
TIME Armed
Area ? was armed automatically using one of the timer controls
TIME Disarmed
Area ? was disarmed automatically using one of the timer controls
DEFERRED
The arming mode was deferred for area ?
ALARM ABORT
An Open After Alarm-Abort has occurred for area ?
REMOTE Armed
Area ? was armed using the Wintex UDL software
REMOTE Disarmed
Area ? was disarmed using the Wintex UDL software
QUICK Armed
Quick Arm from keypad #,#
RECENT Armed
Area ? has been armed recently
#,# RESET AREAS
Area have been reset using keypad #,# following an Intruder alarm
Engineer Reset
A reset has been performed using an Engineers code
Anti-Code Reset
A reset has been performed using the Anti-code reset procedure
Remote Reset
A reset has been performed using the ‘Remote Reset’ input
Redcare Reset
A reset has been performed by the Redcare
Key switch Reset
A reset has been performed using a key switch
User Reset
A reset has been performed using a User code
EXP #,# Reset
A reset has been performed using the input on expander #,#
INS177
31
Operating the Alarm System
Premier Series User Guide
Remote PC Reset
A reset has been performed by the remote download PC
FUSE #,# FAIL
The Auxiliary 12V Fuse in device #,# has failed
AC POWER
The control panel has registered a AC Mains failure
LOW BAT
The control panel has registered a low battery condition
POWERED UP
System Power Up (without doing a factory restart)
BELL FUSE
The control panel Bell Fuse has failed
LINE FLT
There is a problem with the telephone line
Panel Line Fault
The control panel line fault input has been activated
Redcare Line Fault
The Redcare has detected a line fault
Com??? Line Fault
The Com300, 2400 or ISDN has detected a line fault
Exp #,# Line Fault
The Input on expander #,# has been activated
COMS FAILED
The Communicator has failed to report to the Alarm Receiving Centre
DOWNLOAD START
An Upload/Download has been initiated
DOWNLOAD END
The Upload/Download has finished
LOG ALERT
80% of the Event Log has filled (since the last Upload/Download)
DATE CHANGED
The control panel Time has been changed
TIME CHANGED
The control panel Date has been changed
Event Log Hotkeys
When viewing the system log there are 8 hotkeys available. These hotkeys allow certain
events to be found easier without the need for searching.
The following hotkeys are available:
! = Priority Alarms (PA, Fire etc.)
0 = Normal Alarms (Guard, 24hr, Entry/Exit etc.)
, = Opens and Closings (Arm, Disarm etc.)
- = Omits and Reinstates (Zone Omits etc.)
4 = Maintenance (System Tests, Engineer Program etc.)
. = Tampers (Zone, Bell, Aux etc.)
/ = Test Calls (Communicator Active, successful etc.)
5 = Entry/Exit (Entry and Exit Procedures)
3 = User Codes (User codes being used)
32
INS177
Premier Series Master User Guide
Programming the Alarm System
Changing Your User Code
Users with access to this option can change their own User codes. User codes are
unique to each user and can be 4, 5 or 6 digits long.
!"
Only the User code that is entered to access the change code menu will be changed.
Before changing your code, it is vital that you memorise or write down the new
code you are about to program. Failure to remember your code will require an
engineer visit to re-program a new code for you. This may incur a call-out charge.
To change your User code, proceed as follows:
Enter the User code that requires changing 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press 0
K($6(=$9"13$3(
!B"12,$!(H,E
Press #
013,&$Z,9$!(H,L
$$$$$VVVVVV
Enter a new 4, 5 or 6-digit User code 1111
013,&$Z,9$!(H,L
$$$$$VV^c^c
Press # to accept the new code
Press ) to exit the menu
The display will return to normal.
INS177
33
Premier Series User Guide
Operating the Alarm System
Setting up Zones for Chime
Users with access to this option will be able to select which zones cause the internal
sounders to chime every time they are activated. Chime would normally be used on a front
door, back door, exit button etc.
!"
Zones will only cause the internal sounders to chime if Chime is turned on (see
page 22 for details on turning Chime on and off).
To setup zones for Chime, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press +
2
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press &
K($6(=$9"13$3(
0H.3$!B.',$O(1,5
Press #
O(1,$>>A$+.#,13
*&(13$K((&$$$$$L
Enter the zone number 111 or use the * key to search
O(1,$>AT$+.#,13
D"/N$K((&$$$$$$L
Press $ to select Chime
Once for Chime 1, twice for Chime 2 etc
O(1,$>AT$!B.',$@
D"/N$K((&$$$$$$L
Repeat for other zones if required
Press + when finished
Press ) to exit the menu
The display will return to normal.
34
INS177
Premier Series Master User Guide
Programming the Alarm System
Testing the Sounders and Strobe
Users with access to this option can test various system outputs to ensure that they operate
correctly. These include any outputs that have been programmed for specific operations i.e.
bringing on floodlights, sounding buzzers etc. The internal sounders, speakers and the
external sounder can also be tested to ensure that they are operating correctly.
!"
Any outputs that have been left ‘On’ will be turned ‘Off’ when the menu is exited.
To test the Sounders and Strobe, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press +
2
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press K($6(=$9"13$3(
K($+653,'$3,535E
Press #
8=5B$e0+$3($3,53
D,##$.5$$$$$L:;;
Press 3 to select the BELL test
Press ! to select the STROBE test
Press 0 to select the SPEAKER test
Press , to select the USER OUTPUTS test
Press - to select the DISPLAY test
i.e. 2 for Speaker test
8=5B$e0+$3($3,53
+F,"N,&$$$$$L:;;
Press # to test the selected output
Press +, when finished
Press ) to exit the menu
The display will return to normal.
INS177
35
Premier Series Master User Guide
Programming the Alarm System
Walk Testing the System
Users with access to this option can walk test any of the zones on the system to ensure that
they operate correctly. A walk test can only be performed when the system or area is disarmed.
24 Hour zones (except Fire and Tampers) are disabled during walk test allowing Audible PA
buttons, Silent PA buttons, etc. to be tested.
To perform a walk test, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press 4
K($6(=$9"13$3(
K($M"#N$3,53E
Press #
M"#N$3,53$"&,"5L
$$L$IIIIII))$[
Use keys ! - 5 to select an area for walk testing
M"#N$3,53$"&,"5L
$$L$%IIIII))$[
Press # to start the walk test
$$$$I$Z:Z0$I
Every time zones are activated the keypad will chime
O(1,$>A>L%/3.-,
C(=12,$K,3,/3(&$L
Press +, when finished
Press ) to exit the menu
The display will return to normal.
36
INS177
Premier Series Master User Guide
Programming the Alarm System
Enabling Engineer Access
If Engineer access (either on-site or via remote download computer) has been
programmed as User authorised, this option must be used to allow the Engineer access to
the programming menu. Users with access to this option can authorise Engineer access.
!"
Engineer access is only permitted for 4 hours after it is enabled, after which, it will
automatically be disabled again.
To enable Engineer access, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
01"X#,$012.1,,&E
Press #
012.1,,&$%//,55L
K.5"X#,H
Press $ to enable/disable Engineer access
012.1,,&$%//,55L
01"X#,H
Press #
Press ) to exit the menu
The display will return to normal.
INS177
37
Premier Series Master User Guide
Programming the Alarm System
Setting the System Time
The alarm system has a real time clock that is used to date and time stamp events that
are recorded within the system Log. Users with access to this option will be able to set
the Time on your alarm system.
To set the System Time, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press /
K($6(=$9"13$3(
+,3$+653,'$<.',E
Press #
013,&$Z,9$<.',$L
$$$$$A@R@^$D+<
Enter the new time (24 Hour format) 6677
013,&$Z,9$<.',$L
$$$$$@ARST$D+<
Press ) to change between BST and GMT
013,&$Z,9$<.',$L
$$$$$@ARST$f7<
Press #2
Press ) to exit the menu
The display will return to normal.
38
INS177
Premier Series Master User Guide
Programming the Alarm System
Setting the System Date
The alarm system has a real time clock that is used to date and time stamp events that
are recorded within the system Log. Users with access to this option will be able to set
the Date on your alarm system.
To set the System Date, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
Press +
2
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press 5
K($6(=$9"13$3(
+,3$+653,'$K"3,E
Press #
013,&$Z,9$K"3,$L
$$$$>?d>bd>A
Enter the new date 887799
013,&$Z,9$K"3,$L
$$$$@Sd>Td>A
Press # when finished
Press ) to exit the menu
The display will return to normal.
INS177
39
Premier Series Master User Guide
Programming the Alarm System
Overriding the Control Timers
The system has Control Timers that may have been programmed to activate outputs,
arm areas or lockout users at different times of the day. Users with access to this option
can turn the control timers on and off manually if required.
To turn the control timers on & off, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
:-,&&.H,$<.',&5E
Press #
!(13&(#$<.',&
))))))))$.5$(1
Use keys ! - 5 to toggle control timers on and off
(i.e. 1 = Timer 1)
!(13&(#$<.',&
A)))))))$.5$(1
Press # when finished
Press ) to exit the menu
The display will return to normal.
40
INS177
Premier Series Master User Guide
Programming the Alarm System
Altering the Control Timers
The system has Control Timers. Each timer has two ON and OFF times, and can be
programmed to operate on any day of the week. Once configured the timers can be
used to automatically arm or disarm areas, lockout User codes and control outputs etc.
Users with access to this option can program the Control Timers.
To program control timers, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
%#3,&$3.',&5
Press #
!(13&(#$<.',&$A"
.5$:1$"3$L>>R>>
Use * to Select a Control Timer from 1 to 8
!(13&(#$<.',&$@"
.5$:1$"3$L>>R>>
Enter the first On time (24 Hour format) 6677
!(13&(#$<.',&$@"
.5$:1$"3$LA@RbT
Press # when finished
<.',&$@"$:1$K"65
))))))))))))))))
Use keys ! - / to select the On days (SUN to SAT)
(i.e. ! and 0 = Sunday and Monday)
INS177
41
Premier Series Master User Guide
Programming the Alarm System
<.',&$@"$:1$K"65
+=7())))))))))))
Press # when finished
!(13&(#$<.',&$@"
.5$:;;$"3$LA@R>>
Enter the first Off time (24Hour format) 6677
!(13&(#$<.',&$@"
.5$:;;$"3$LASR>>
Press # when finished
<.',&$@"$:;;$K"65
))))))))))))))))
Use keys ! - / to select the first Off days (SUN to SAT)
(i.e. . and / = Friday and Saturday)
<.',&$@"$:;;$K"65
))))))))))*&+"))
Press # when finished
!(13&(#$<.',&$@X
.5$:1$"3$L>>R>>
Repeat programming for the timers Second
On times, On days, Off times and Off days
Repeat for other Control Timers
Press + when finished
Press ) to exit the menu
The display will return to normal.
42
INS177
Premier Series Master User Guide
Programming the Alarm System
Adding New Users to the System
When the control panel is first installed, only the Engineer code and the Master User
code exist, additional users need to be added to the alarm system manually.
!"
The factory default Master User code is 4./5.
The Master User code is always User 01 and can never be deleted.
Programming New Users
Each User on the system is made up of the following elements. 1, 2 or 8, 3 and 4, these are
essential for the code/TAG to function correctly, items 5, 6 and 7 are optional.
1. User Number
When users are assigned to the system, they need to be identified by the control panel.
Each user is identified as Users 01, 02, 03 etc. User 01 is always the Master User.
2. User Code
This is a unique 4, 5 or 6 digit code number that is assigned to a user (the system will allow
a mixture of different lengths). The User code must be entered at a keypad to operate the
alarm system.
3. User Areas
Any number of areas can be assigned to the selected user. Assigning areas to a user
determines which areas can be armed, disarmed, reset etc. by that user. In addition,
assigning areas to a user determines which of the area related functions i.e. omitting
zones, silent arming etc. will be available to that user.
4. User Types
The User type determines which functions are available to the user i.e. arming,
disarming, resetting etc. and also, which options the user can access i.e. Setup Users,
System Tests etc.
5. User Time Lock
This option allows the selected user to be denied access to the system at different times
of the day and days of the week. When a Control Timer is assigned to a user, the User
code will not allow access to any functions during the timers ‘On’ period.
6. User Name Text
Each user can be assigned up to 8 characters of name text. The name text is displayed
whenever a code is entered and also when reading the log, making identification of
people using the alarm easier.
7. Door Control
This option would normally be used for access control. Users are able to open/unlock
doors that are assigned to their user code.
8. Proximity TAG
As well as or instead of operating the alarm system with a 4, 5 or 6-digit code number, it
is also possible to operate it by presenting a Proximity TAG to the keypad (this requires a
Proximity keypad).
INS177
43
Programming the Alarm System
Premier Series Master User Guide
User Types
The User type determines which functions are available to the user i.e. arming, disarming,
resetting etc. and also, which options the user can access i.e. Setup Users, System Tests
etc. The following User types are available:
1: Master
Master users can arm, disarm, omit zones, silence alarms and reset their assigned areas.
In addition, Master users can access all User menu options. Master users can also
change their own User codes and assign new users to the system. The Master user will
also activate any output programmed as ‘Door Strike’.
2: Manager
Manager users can arm, disarm, omit zones, silence alarms and reset their assigned
areas. In addition, Manager users can access all User menu options except Setup Users.
Manager users can also change their own User codes.
3: Standard
Standard users can arm, disarm, omit zones, silence alarms and reset their assigned areas.
In addition, Standard users can access all User menu options except for Setup Users,
System Tests, and Change Timers. Standard users can also change their own User codes.
4: Local (Premier 48,88,168,640) Shunt (Premier 24)
Local users behave the same way as Standard users. However, Local users can only arm
and disarm areas assigned to their codes from keypads assigned to the same areas.
Shunt users can omit and reinstate any zone that has been programmed as ‘Shuntable’.
5: Duress
Duress users behave the same way as Standard users. However, Duress users will activate
any outputs programmed as ‘Panic Alarm’ or ‘Duress’ whenever their code is entered.
6: Arm Only (Premier 48,88,168,640) Reset Only (Premier 24)
Arm Only users can only arm and reset their assigned areas.
Reset Only users can only disarm following an alarm and then reset, rearm the alarm again.
7: Door Strike
Door Strike users have no access to User functions or Menu options. However, Door Strike
users will activate any outputs programmed as ‘Door Strike’ whenever their code is entered.
8: Vacation
Vacation users behave as Standard users. However, Vacation users are automatically
deleted the first time that the Master User code (User 01) is used to disarm the system.
!"
A Vacation user is only deleted by the Master user after it has been used to disarm
the system at least once.
9: Custom
Custom users can access any functions and User menu options that have been
assigned to them in ‘User Options 1 or 2’ and ‘User Config.’. This flexibility allows new
User types to be created that have their own unique set of characteristics. Any number of
Custom users can be assigned to the system and each one will respond differently,
depending on the functions and features that have been assigned to them.
44
INS177
Premier Series Master User Guide
Programming the Alarm System
Available Options
The table below shows the options that are available to each user.
!"
All users that have access to the ‘Arming Menu’ have the ability to ‘View Zone
Status’, ‘Set Chime Areas’, ‘View Act. Faults’ and ‘View Act. Counts’.
All users have access to the ‘User Menu’ have the ability to ‘View Event Log’,
‘Adjust Volumes’ and ‘Print Event Log’.
User Options 1
Engineer
Master
Manager
Standard
Local
Duress
Arm Only
Door Strike
Vacation
Arming
Arming
Arming
Arming
Arming
Arming
Arming
-
Arming
Custom
Arming
Disarming
Disarming
Disarming
Disarming
Disarming
Disarming
-
-
Disarming
Disarming
Omitting
Omitting
Omitting
Omitting
Omitting
Omitting
Omitting
-
-
Omitting
Eng. Reset
-
-
-
-
-
-
-
-
-
-
-
-
-
Local Arming
-
-
-
-
-
-
-
-
-
Local Disarm
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Disarm First
Disarm First
- Disarm First
Disarm First
Disarm First
Disarm First
Disarm First
-
Disarm First
Disarm First
User Options 2
Engineer
Master
Manager
Standard
Local
Duress
Arm Only
Door Strike
Vacation
Custom
User Menu
User Menu
User Menu
User Menu
User Menu
-
User Menu
-
User Menu
User Menu
Eng. Program
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Vacation
-
Door Strike
Door Strike
-
-
-
-
-
Door Strike
-
-
Call Rem PC
Call Rem PC
Call Rem PC
-
-
-
-
-
-
-
-
-
-
-
-
Duress Code
-
-
-
-
Open/Close
Open/Close
Open/Close
Open/Close
Open/Close
Open/Close
Open/Close
-
Open/Close
Open/Close
Custom
User Config
Engineer
Master
Manager
Standard
Local
Duress
Arm Only
Door Strike
Vacation
Change Code
Change Code
Change Code
Change Code
Change Code
-
-
-
-
-
Chime Zones
Chime Zones
Chime Zones
Chime Zones
Chime Zones
-
-
-
-
-
Change Timer
Change Timer
Change Timer
-
-
-
-
-
-
-
System Tests
System Tests
System Tests
-
-
-
-
-
-
-
Setup Users
User Setup
-
-
-
-
-
-
-
-
Eng. Access
-
-
-
-
-
-
-
-
-
Add Eng Code
-
-
-
-
-
-
-
-
-
NVM Locking
-
-
-
-
-
-
-
-
-
INS177
45
Programming the Alarm System
Premier Series Master User Guide
User Options 1
This menu defines which options are available to the user when their code is entered.
This menu is not available to all users.
Press
* to scroll through the options and press $ to select them or use keys
! - 5 (‘Letter’ = option IS selected, ‘Star’ = option is NOT selected).
The following options are available:
A - Arming
Areas assigned to the selected user can be armed.
D - Disarming
Areas assigned to the selected user can be disarmed.
O - Omitting
Zones assigned to the same areas as the selected user can be omitted, providing that
they have the ‘Omit’ attribute assigned to them.
R - Eng. Reset (Engineers only)
Areas programmed as ‘Engineer Reset’ can be reset after an Alarm has occurred.
a - Local Arming (not on Premier 24)
The User can only arm areas that the keypad is assigned to.
d - Local Disarm (not on Premier 24)
The User can only disarm areas that the keypad is assigned to, or areas that are in entry or
alarm (provided that the code has that area assigned to it).
Y - Auto ‘YES’
After a code is entered, pressing # to confirm the next action is not required.
F - Disarm First (not on Premier 24)
If an area is armed and the user enters their code, the ‘Disarm’ option is displayed first.
The following attributes are only available on the Premier 24.
!"
Some of the following options may not always be selectable or de-selectable.
T - Lock TAG = PGM2
The Users TAG is disabled whenever PGM2 is active.
C - Lock Code = PGM3
The Users code is disabled whenever PGM3 is active (default = during the Entry mode).
U - Lock User = PGM4
The Users TAG and Code is disabled whenever PGM4 is active (default = Control Timer 4).
O - Open/Close
The selected user will report open (disarm) and close (arm) events to an Alarm Receiving
Centre every time they arm or disarm.
46
INS177
Premier Series Master User Guide
Programming the Alarm System
User Options 2
This menu defines which options are available to the user when their code is entered.
This menu is not available to all users.
Press
* to scroll through the options and press $ to select them or use keys
! - 5 (‘Letter’ = option IS selected, ‘Star’ = option is NOT selected).
The following options are available:
U - User Menu
The selected user has access to the User menu. However, the selected user will only
have access to options assigned in ‘User Config.’ (see page 48 for details).
E - Eng. Program (Engineers only)
Only Available to Engineers.
D - Dual Code
The selected user can only access an area when a second User code (with the ‘Dual
Code’ attribute and also assigned to the same area) is entered. Dual Code users will also
activate the ‘1st and 2nd Code’ output type.
V - Vacation
The selected user is enabled the first time it is used to disarm the system and can be
used as many times as required. However, it will be automatically deleted the first time
that the User 01 code is used to disarm. Vacation users will only be deleted by the
Master user, once they have been used on the system.
S - Door Strike
The selected user will activate any outputs programmed as ‘Door Strike’, whenever their
codes are entered.
R - Call Rem. PC
The selected user has access to the ‘Call Remote PC’ option, allowing them to initiate a
call to a remote Upload/Download PC (see page 54 for details).
C - Duress Code
The selected user will activate any outputs programmed as ‘Duress’, whenever their
codes are entered.
O - Open/Close
The selected user will report open (disarm) and close (arm) events to an Alarm Receiving
Centre every time they arm or disarm.
INS177
47
Programming the Alarm System
Premier Series Master User Guide
User Config.
This menu defines which menu options are available to the user when their code is entered.
This menu will only be displayed if a Custom User type is selected AND ‘User Menu’
(User Option: U) is enabled (see page 47 for details).
Press * to scroll through the options and press $ to select them or use keys
! - 5 (‘Letter’ = option IS selected, ‘Star’ = option is NOT selected).
The following options are available:
C - Change Code
The selected user can change their own User code.
Z - Chime Zones
The selected user can access the ‘Edit Chime Zones’ option, allowing them to select
which zones chime when activated (see page 34 for details).
T - Change Timers
The selected user can access the ‘Override Timers’ (see page 40 for details) ‘Alter
Timers’ (see page 41 for details) ‘Alter Part Arms’ (see page 53 for details) ‘Alter Hol.
Dates’ (see page 55 for details) and ‘Edit Phone No.’ (see page 58 for details) menu
options.
S - System Tests
The selected user can access the ‘System Tests’ option, allowing them to walk test
zones, activate the external sounder etc. (see page 35 for details).
U - Setup Users
The selected user can access the ‘Setup Users’ option, allowing them to alter existing
users or assign new users (see page 43 for details). However, users cannot assign User
types to the system that have a higher access level than themselves. Also, if a user
assigns a Custom User type, functions that are not available to them cannot be assigned
to the Custom user.
E - Eng. Access
The selected user can access the ‘Enable Engineer’ option, allowing them to authorise
Engineer access or Remote UDL access to the system (see page 30 for details).
A - Add Eng. Code (Engineers only)
Only Available to Engineers.
N - NVM Locking (Engineers only)
Only Available to Engineers.
48
INS177
Premier Series Master User Guide
Programming the Alarm System
User Name Text
Each user can be assigned up to 8 characters of name text. This can be beneficial when
reading the log, as identification of people is made easier.
Text is programmed in a similar way to mobile phones. Characters are selected by
pressing the corresponding key the appropriate number of times (to select a character
on the same key, press * to move the cursor along).
Some control panels also features Predictive text. This can be used to make inserting
words easier, i.e. when spelling the word COLIN, instead of typing 222666555444666, all
that you need to do is type 26546 and the word is automatically selected.
!"
It is advised that predictive text be turned off when programming User name text
as the library is not comprehensive enough to include all known names.
The library cannot be edited i.e. words cannot be added or changed.
The table below shows the keys to use and the characters that are assigned to them:
Key
Character
32 _ 0
!2 . , ? ! 1 @ “ - & % / + = $
02 A B C 2 a b c
,2 D E F 3 d e f
-2 G H I 4 g h i
42 J K L 5 j k l
.2 M N O 6 m n o
/2 P Q R S 7 p q r s
52 T U V 8 t u V
"2 W X Y Z 9 w x y z
*2 Move Cursor
)2 Backspace (delete)
&2 Copy Text
'2 Paste Text
%2 Predictive Text
$2 Upper/Lowercase, Predictive text and Clear Screen
INS177
:
;
49
Premier Series Master User Guide
Programming the Alarm System
Programming Users
To Program Users, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
+,3=F$P5,&5E
Press #
+,3=F$P5,&5$
P5,&$>@R
Select a user 11 or use the * key to search
+,3=F$P5,&5$
P5,&$A>R
To Program a Code
To Assign a TAG
To Import a TAG
To Assign a FOB
Press #
Press (
Press '
Press %
013,&$P5,&$!(H,L
$$$$$VVVVVV
K($6(=$9"13$3(
%HH$<%f$3($P5,&E
$\78:4<\Zf$<%f
8&,5,13$<%f$Z:Mg
P5,&$A>$4,'(3,$L
%/3.-"3,$K,-./,
Enter the new
User code
Press #
Present the TAG to
The ‘Prox’ symbol
on the keypad
Press any of the
buttons on the
Radio FOB
(A confirmation
tone will be heard)
(A confirmation
tone will be heard)
1111 2
(The code can be 4,
5 or 6-digits long)
Press #
See next page...
50
8&,5,13$<%f$Z:M$g
Present the TAG to
The ‘Prox’ symbol
on the keypad
(A confirmation
tone will be heard)
INS177
Premier Series Master User Guide
Programming the Alarm System
From Previous page...
P5,&$A>$"&,"5$L
$$L$%IIIIIII$[
Use keys ! - 5 to select/deselect areas then press #
P5,&$A>$<6F,$.5L
Z(3$.1$P5,
Use keys ! - 5 to select a User type or use the * key to search
(Refer to page 43 for a list of available User types)
P5,&$A>$<6F,$.5L
+3"1H"&H
Press #2
These options are only displayed if a Custom User type is selected
Press * to scroll through options and press $ to select the option
(‘Letter’ = option IS selected, ‘Star’ = option is NOT selected).
%&'.12
L%$K$:$I$I$I$I$*
Press # when finished
P5,&$A>$:F3.(1$A
$%$K$:$I$I$I$I$*
Press # to select ‘Options 2’ and press $ to edit
%//,55$P5,&$7,1=
LP$I$I$I$I$I$I$:
Press # when finished
P5,&$A>$:F3.(1$@
$P$I$I$I$I$I$I$:
Press # to select ‘Config’ and press $ to edit
(The following option is only displayed if ‘User Menu’ has been selected, see above)
!B"12,$:91$!(H,
L!$O$I$I$I$0$I$I
Press # when finished
P5,&$A>$!(1;.2)
$!$O$I$I$I$0$I$I
Press #
P5,&$A>$C(/N,HL
X6$3.',&))))))))
Use keys ! - 5 to select a timer if required then press #
P5,&$A>$Z"',$.5R
Press $ to edit the User name text, press # when finished
(For details on programming text please refer to page 49). Press #2
2
INS177
51
Premier Series Master User Guide
Programming the Alarm System
This option is only displayed if a User with the ‘Door Strike’ attribute is selected
P5,&$A>$K((&$!3#
$$L$IIIIIIII$[
Use keys ! - 5 to select/deselect doors then press #
K($6(=$9"13$3(
%HH$<%f$3($P5,&E
Press # to assign TAG or $ to ignore TAG programming
8&,5,13$<%f$Z:M$g
Present the TAG to the ‘Prox’ symbol on the keypad
(A confirmation tone will be heard)
Press + when finished
Press ) to exit the menu
The display will return to normal.
Deleting Users
To delete User codes proceed as follows:
Ensure that Setup Users is selected, the display should look like this:
+,3=F$P5,&5$
P5,&$>@R
Select a user 11 then press #2
013,&$P5,&$!(H,L
$$$$$VVVVVV
Press )
K($6(=$9"13$3(
K0C0<0$P5,&$AT
Press # to confirm deletion of the selected User code
Press + when finished
Press ) to exit the menu
The display will return to normal.
52
INS177
Premier Series Master User Guide
Programming the Alarm System
Setting up the Part Arms
When a Part Arm 1, 2 or 3 is selected, pre-programmed zones are omitted to allow
access to certain parts of the building. This option allows these zones to be programmed
or altered by any User that has access to the ‘Omit’ menu.
To set up the Part Arms, proceed as follows:
Enter a valid User code 1111, the display should look like this:
K($6(=$9"13$3(
%&'$+653,'E
Press +
2
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press '
K($6(=$9"13$3(
%#3,&$8"&3$%&'5E
Press #
*(&$8"&3$%&'$A
O(1,$>>A$.5$L$:Z
Press % to select Part Arm 1
Press & to select Part Arm 2
Press ' to select Part Arm 3
*(&$8"&3$%&'$@
O(1,$>>A$.5$L$:Z
Enter a zone number 111 or use the * key to search
*(&$8"&3$%&'$@
O(1,$>A>$.5$L$:Z
Press $ to turn zone ON or OFF for the selected Part Arm
*(&$8"&3$%&'$@
O(1,$>A>$.5$L:**
Repeat for other zones
Press + when finished
Press ) to exit the menu
The display will return to normal.
INS177
53
Premier Series Master User Guide
Programming the Alarm System
Calling a Remote PC
This option is used to initiate a call to a remote uploading and downloading computer.
To send a call to a Remote PC, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
!"##$4,'(3,$8!E
Press #
!"##$D"/N$Z()AR
>A@bST?a^c>
Use keys ! - , to select a Call Back number
(i.e. 0 = Call Back number 2)
!"##$D"/N$Z()@R
>A@bST?a^c>
Press # to start the call back
Press ) to exit the menu
The display will return to normal.
54
INS177
Premier Series Master User Guide
Programming the Alarm System
Altering the Holiday Dates
This option is used to alter the programmable Holiday Dates. These dates can be used to
prevent the control timers from operating on certain dates of the year (bank holidays etc.)
or to only operate on certain dates (reminders).
To alter Holiday Dates, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
%#3,&$U(#)$K"3,5
Press #
U(#.H"6$K"3,$AL
$$$$>>d>>d>>
Use * to Select a Holiday Date from 1 to 8
U(#.H"6$K"3,$bL
$$$$>>d>>d>>
Press $ then enter the new date 8877992
U(#.H"6$K"3,$bL
$$$$@SdA@d>@
Press # to accept the new Holiday Date
Repeat for other holiday dates
Press + when finished
Press ) to exit the menu
The display will return to normal.
INS177
55
Premier Series Master User Guide
Programming the Alarm System
Adjusting Speaker Volumes
This option is used to adjust the volume level of speakers that are connected to the
control panel, keypads and expanders.
To adjust speaker volumes, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
%HY=53$Q(#=',5E
Press #
8"1,#$Q(#=',
$$$#,-,#$h$?
Press * to select a Panel, Keypad or Expander speaker
J,6F"H$>b$Q(#=',
$$$C,-,#$h$S
Press $ then ! - 5 to enter a volume level
(1 = Minimum, 8 = Maximum)
Press & to hear the new volume level
J,6F"H$>b$Q(#=',
$$$C,-,#$hLa
Press # to accept the new speaker volume
Repeat for other speakers
Press + when finished
Press ) to exit the menu
The display will return to normal.
56
INS177
Premier Series Master User Guide
Programming the Alarm System
Printing the Event Log
If a printer or terminal is connected to the control panel, this option can be used to print out
events from the systems Event Log.
To print the Event Log, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
8&.13$0-,13$C(2E
Press #
Z='X,&$(;$,-,135
$$$$$L$>>T>
Enter the number of required events 1111
Z='X,&$(;$,-,135
$$$$$L$>T>>
Press # to print the Event Log
Press ) to exit the menu
The display will return to normal.
INS177
57
Premier Series Master User Guide
Programming the Alarm System
Editing a Mobile Telephone Number
If the control panel has been programmed to send SMS text messages to a mobile phone
in the event of an alarm occurring etc. this option allows the mobile telephone numbers to
be programmed.
To edit a Phone Number, proceed as follows:
Enter a valid User code 1111
K($6(=$9"13$3(
%&'$+653,'E
2
Press +
K($6(=$9"13
P5,&$7,1=E
Press #
K($6(=$9"13$3(
Q.,9$0-,13$C(2E
Press * until the display looks like this:
K($6(=$9"13$3(
0H.3$8B(1,$Z()E
Press #
<,#,FB(1,$Z()$AL
$!%Z$Z:<$!U%Zf0
Press * to select the required number
<,#,FB(1,$Z()$bL
Press $ to edit the number
>a^c>A@bST?
$$$$$$$$$$$_LA@b
Enter the required mobile phone number then press #
<,#,FB(1,$Z()$bL
>a^c>A@bST?
Press + when finished
Press ) to exit the menu
The display will return to normal.
58
INS177
Premier 8 Series Master User Guide
Specifications
5. Specifications
European Standards
Conforms to European Union (EU) Low Voltage Directive (LVD) 73/23/EEC and ElectroMagnetic Compatibility (EMC) Directive 89/336/EEC
The CE mark indicates that this product complies with the European requirements for
safety, health, environmental and customer protection.
This equipment is designed to enable an intruder alarm system in which it is installed to
comply with the requirements of security grades 1 or 2 of EN 50131-1 and EN 50131-6
and is suitable for installation in any indoor environment.
Warranty
All Texecom products are designed for reliable, trouble free operation. Quality is carefully
monitored by extensive computerised testing. As a result the control panel is covered by
a two-year warranty against defects in materials or workmanship.
As the control panel is not a complete alarm system but only a part thereof, Texecom
cannot accept responsibility or liability for any damages whatsoever based on a claim
that the control panel failed to function correctly.
Due to our policy of continuous improvements Texecom reserve the right to change
specification without prior notice.
Premier Keypads and Expanders are protected by UK & International Registered Design.
Registered Design Number: 2089016 and 3004996.
Premier is a trademark of Texecom.
INS177
59
Premier Series Master User Guide
Installation Records
6. Installation Records
Areas
No.
Description
Exit
Time
Entry
Time 1
Entry
Time 2
Bell
Delay
Bell
Duration
Abort
Time
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Sec.
Sec.
Sec.
Min.
Min.
Sec.
Keypads
RKP
No.
60
Keypad
Location
Keypad
Area
Quick
Arm
Emergency Keys
PA
Fire
Med
INS177
Premier Series Master User Guide
Installation Records
Zones
Zone
No.
Zone
Description
Zone
Type
Zone
Areas
Zone
Omit
Part Arms
1
2
3
Tick Zones Included in Part Arms
INS177
61
Premier Series Master User Guide
Installation Records
Zone
No.
Zone
Description
Zone
Type
Zone
Areas
Zone
Omit
Part Arms
1
2
3
Tick Zones Included in Part Arms
62
INS177
Premier Series Master User Guide
Installation Records
User Codes
User
01
Name
Type
Default
Master
5678
New Code
Area
Time Lock
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
INS177
63
Installation Company Details
Installation Engineer:
Installation Company:
Address:
Telephone Number:
Installation Date:
Service Record
Date Serviced
Comments
Engineer
Emergency Telephone Numbers
For 24 Hour Call Out
For Anti-Code Reset
Control Panel
Details
Model
Premier 24 ❏
Premier 48 ❏
Premier 88 ❏
Location
© TEXECOM LTD. 2000 - 2004
INS177-4
Premier 168 ❏
Premier 640 ❏
Download PDF