Door Drive Manual Click for

ADCO Controls
Elevator Door Control User Manual
ADCO
User manual
Elevator Door Control
ADPMDC
ADCO CONTROLS
CONTACT:
Tel/fax: +917925841070
Web: www.adcocontrols.com
Email:info@adcocontrols.com
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
1
ADCO Controls
Elevator Door Control User Manual
Electrical Connection:
Power Connection:
Elevator Door Drive will operate on 220VAC +/-15 %, 50Hz or 60Hz with 1A
Max Current from the Main Supply. There is Power Transformer between Drive and
mains. So main supply will go to Power unit and Drive Supply will come from the power
unit. There is plug and play connector between Drive and Power unit.
Motor Connection:
Just connect Motor Connector as per shown in drive, it is white 10 pin connector
plug and play type without screw. This connector includes motor three phase supply as
well as Encoder wire also.
Control Inputs:
+12V
PH-
PH+
COM
1
Door Open
GND
2
DO
3
2
4
1
5
DC
6
2
7
1
8
Door Close
9
+12V
10
GND
1. Door Open and Door Close Connection:
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
2
ADCO Controls
Elevator Door Control User Manual
2. Photo Sensor Connection:
Photo Sensor is used in almost all the Automatic Door Lift for the safety
of the passengers. Drive has 12VDC, 1A output power for photo sensor so
no Extra Power supply required for the photo sensor.
DC
DO
5
4
3
2
1
DO
1
DC
2
COM
3
COM
4
PH+
5
PH+
GND
6
PH-
7
PH-
8
+12V
9
+12V
10
GND
A : NPN Output Type Photo Sensor
NPN
Power Supply
For Photo
Sensor
9
8
7
6
+12V
GND
+12V
10
GND
B : PNP Output Type Photo Sensor
PNP
Power Supply
For Photo
Sensor
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
3
ADCO Controls
Elevator Door Control User Manual
3
2
1
DO
4
DC
5
COM
GND
6
PH+
7
PH-
8
+12V
9
+12V
10
GND
C : Relay Output Type Photo Sensor
Power Supply
For Photo
Sensor
Photo Sensor
1
2
Outputs:
There are 4 relay output in Elevator Door Drive. Relay Contact have 5A/230VAC
or 20A/24VDC. Drive gives information on the display as well as through relay like Door
Fully Open, Door Fully Closed, Photo Sensor Detection and Obstruction Detection.
Relay Output:
22
21
20
OBSTRUCTION
RELAY
19
18
17
PHOTO
RELAY
16
15
14 13 12 11
DCLIMIT
RELAY
DOLIMIT
RELAY
Fully Opened
Fully Closed
Photo Sensor
Obstruction
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
4
ADCO Controls
Elevator Door Control User Manual
Parameter List:
No
0
1
2
3
4
5
6
7
8
9
A
b
C
d
E
F
O
R
L
P
T
N
J
U
Name
Close Decelaration
Opening Speed
Closing Speed
Open Slow Speed
Close Slow Speed
Open Slow Located Distance
Close Slow Located Distance
No of Input (1,2)
Opening Side Selection
Acceleration Time
Deceleration Time
Open Holding Force
Close Holding Force
Hold Release Time
Safety Force
Skate Speed
Skate Distance
Open Safety Force
Max Current
DispMode
OpenSlowCurrentLimit
CloseSlowCurrentLimit
Pid_INC
DLLPID1
Range
0-99
0-99
0-50
0-6
0-6
0-99
0-99
1 or 2
0-1
01-60
01-60
0-6
0-6
0-99
00-50
00-20
00-99
00-99
00-99
0-6
0-99
0-99
0-99
0-99
Factory Reset Value
8
50
40
1
1
25
25
1
0
20
6
2
2
25
30
4
10
30
55
4
25
15
2
10
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
5
ADCO Controls
Elevator Door Control User Manual
Parameter Explanation:
1. Open Speed: it is the speed at which the doors will be opened in there full
speed range
2. Close Speed: it is the speed at which the door will be closed in there full speed
range
3. Open Slow Speed: it is the speed at which the doors will be opened after their
slow located distance
4. Close Slow Speed: it is the speed at which the doors will be closed after their
slow located distance
5. Open Slow Located Distance: it is a distance from fully opened position
6.
7.
8.
9.
A.
B.
C.
from which the doors will open with the slow speed. As the value of this distance
increase the doors will be open with slow speed earlier and as the value of this
distance decreases the doors will open with slow speed later.
Close Slow Located Distance: it is a distance from fully closed position
from which the doors will close with the slow speed. As the value of this distance
increase the doors will be close with slow speed earlier and as the value of this
distance decreases the doors will close with slow speed later.
No of Input: User can operate Either 2 or 1 input for the Door Open and Door
Close. If 2 Input Selected both Door Open and Door Close input are activated for
the operation. If 1 input selected only Door Open Input is activated, Door will
open on Command On and Door Close when command off.
Open Side Selection: During Setup First Door will open and DO LED will
glow, in that condition if Door Close change Value in Open Side Selection
parameter if 0 make 1 and if 1 make 0.
Acceleration Time: This parameter varies the time of changing the doors
speed from start to full speed which gives the smooth change over of the doors
speed and prevents doors banging
Deceleration Time: This parameter varies the time of changing the doors
speed from full speed to slow speed which gives the smooth change over of the
doors speed and prevents doors banging.
Open Hold Force: After Fully open operation sometimes the doors slightly
close due to the doors mechanism, to prevent this holding force is required to hold
the doors in the closed position. This parameter decides the holding force to be
applied to the doors after opening the doors.
Close Hold Force: After Fully Close operation sometimes the doors slightly
close due to the doors mechanism, to prevent this holding force is required to hold
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
6
ADCO Controls
Elevator Door Control User Manual
D.
E.
F.
O.
the doors in the closed position. This parameter decides the holding force to be
applied to the doors after Closing the doors
Hold Release Time: During ideal condition holding is not required, like night
or pick off time very less operation is there. During this time holding is not
required, so after fully open or close if no other operation until hold release time,
it will release hold force from the motor.
Safety Force: it is the maximum force(closing Pressure) on any obstacle while
closing the doors, if obstacle pressure is more then doors will be reopen and the
obstruction relay-LED will be On.
This feature prevents any accident in case of failure of safety sensor.
Skate Speed: User can Vary Skate Speed using this parameter.
Skate Distance: Up to Skate Distance Door will open slowly, so it will avoid
the jerk, because up to skate only one door will there and after that landing door
will come.
Installation and Auto Tuning:
Step1: Mount the Drive Unit, Power Supply Unit and Motor on the Door Header
Properly.
Step2: Connect Motor Cable to Drive unit properly.
Step3: Connect Single Phase Supply with “EARTH” Properly to Power Supply
unit.
Step4: Connect Power Cable from Power Supply unit to Drive unit properly.
Step5: Make Power On, Drive Display Will show “RDY”.
Step6: Check all the Parameter as per Requirement, if any change required do the
change as per requirement.
Step7: Press Enter Button for 2 Sec. Screen show “P-00”. It will ask for
Password. Enter 09 Default Passwords. Then it will show two modes
“AUTO” and “PROG”. To enter in auto tuning mode press Enter button
in “AUTO” mode. During Auto Tuning process “INIT LED” will blink
and Door Open/Close Two Times and store the door data. During Auto
tuning if “DO LED” on and Door is closing, change the Open Side
Selection Parameter and Repeat the Procedure again.
Step8: Connect the Control Input and Relay Output from the Main Elevator
Control Panel or any Other Controlling Unit.
Step9: Now it’s ready to Use, Enjoy Automatic Door.
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
7
ADCO Controls
Elevator Door Control User Manual
Programming the Parameter:
There are 3 keys and 4 Display on the top of drive unit. Using 3 keys and 4
display user can the change the parameter as per requirement.
Press Enter Button for 2 Sec. Screen show “P-00”. It will ask for Password.
Enter 09 Default Passwords. Then it will show two modes “AUTO” and
“PROG”. To enter in Programming mode press Enter button in “PROG” mode.
Using Enter key you can reach the parameter you want to change. Using the
Up/Down Key user can change the parameter value. Press the ENTER key up to
end of the parameter list, user will come out of the programming.
ADCO CONTROLS, PLOT-5318, PHASE-4, OPP. RAMOL POLICE CHOWKI,
VATVA GIDC, AHMEDABAD-382445, GUJARAT (INDIA)
8
Download PDF