User`s Manual (concise)

Dukane Projector
9136
Thank you for purchasing this projector.
WARNING
►Before using this product, be sure to read all manuals for this product. See “Using the
CD manual” (12) to read the manuals in the CD. After reading them, store them in a
safe place for future reference.
Contents
Contents of package .................................. 1
Arrangement ............................................. 2
Connecting your devices ........................... 3
Connecting power supply ......................... 4
Turning on the power ................................ 4
Adjusting the projector’s elevator ............. 5
Remote control .......................................... 5
Displaying the picture ............................... 7
Turning off the power ............................... 7
Lamp ......................................................... 8
Air filter................................................... 10
Internal clock battery .............................. 11
Using the CD manual .............................. 12
Regulatory notices .................................. 13
Specifications .......................................... 15
Warranty and after-service ...................... 16
Contents of package
Your projector should come with the items shown below.
Check that all the items are included. Require of your
dealer immediately if any items are missing.
LASER
INDICATOR
STANDBY/ON
VIDEO
RGB
MY SOURCE/
DOC.CAMERA
(1)
SEARCH
BLANK
(2)
LASER
ASPECT
PUSH ENTER
PAGE UP
ESC
(1) Remote control with two AA batteries
(2) Power cord
(3) RGB cable
(4) Lens cover and Rivet and Strap
(5) User’s manuals (Book x1, CD x1)
(6) Security label
PAGE DOWN
MENU
POSITION
AUTO
MAGNIFY
MY BUTTON
ON
1
RESET
VOLUME
+
OFF
2
-
FREEZE
KEYSTONE
MUTE
(3)
(4)
(5)
(6)
CAUTION
►Keep the original packing materials for future reshipment. Be sure to use the original
packing materials when moving the projector. Use special caution for the lens.
1
ENGLISH
User's Manual (concise)
Arrangement
Please arrange the projector and the screen.
Install the projector in a stable, cool and airy place, keeping a space of 30 cm or more
between the sides of the projector and other objects such as walls. Avoid the projector from
a hot, humid, dusty, or smoky place.
Refer to the illustrations and tables below to determine screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1400x1050
(a) Screen size (diagonal)
(b) Projection distance (±10%)
(c) Screen height (±10%), when the vertical lens shift is set full upward.
On a horizontal surface
(b)
(a)
(c) up
(c) down
Suspended from the ceiling
(c) down
(a)
• Consult with your dealer before a
special installation such as suspending
from a ceiling.
(c) up
(b)
(a) Screen
size
[inch (m)]
4 : 3 screen
(b) Projection distance
(c) Screen height
[m (inch)]
[cm (inch)]
min.
max.
down
up
30
(0.8)
0.9
(35)
40
60
70
80
90
100
120
150
200
250
300
350
(1.0)
(1.5)
(1.8)
(2.0)
(2.3)
(2.5)
(3.0)
(3.8)
(5.1)
(6.4)
(7.6)
(8.9)
1.2
1.8
2.1
2.4
2.7
3.0
3.7
4.6
6.1
7.7
9.2
10.8
(47) 1.4 (57)
(71) 2.2 (86)
(83) 2.6 (100)
(96) 2.9 (115)
(108) 3.3 (130)
(120) 3.7 (144)
(144) 4.4 (174)
(181) 5.5 (217)
(241) 7.4 (291)
(302) 9.2 (364)
(363) 11.1 (437)
(424) 13.0 (510)
1.1
(42)
5
6
9
11
12
14
15
18
23
30
38
46
53
(2)
(2)
(4)
(4)
(5)
(5)
(6)
(7)
(9)
(12)
(15)
(18)
(21)
41
55
82
96
110
123
137
165
206
274
343
411
480
(16)
(22)
(32)
(38)
(43)
(49)
(54)
(65)
(81)
(108)
(135)
(162)
(189)
16 : 9 screen
(b) Projection distance
(c) Screen height
[m (inch)]
[cm (inch)]
min.
max.
down
up
1.0
(38)
1.3
2.0
2.3
2.6
3.0
3.3
4.0
5.0
6.7
8.4
10.0
11.7
(51) 1.6 (62)
(78) 2.4 (94)
(91) 2.8 (110)
(104) 3.2 (126)
(117) 3.6 (141)
(131) 4.0 (157)
(157) 4.8 (189)
(197) 6.0 (237)
(263) 8.0 (317)
(329) 10.1 (396)
(395) 12.1 (476)
(462) 14.1 (556)
1.2
(46)
-1
-2
-2
-3
-3
-4
-4
-5
-6
-8
-10
-12
-15
(0)
(-1)
(-1)
(-1)
(-1)
(-1)
(-2)
(-2)
(-2)
(-3)
(-4)
(-5)
(-6)
39
51
77
90
103
116
129
154
193
257
322
386
450
WARNING
►Install the projector in a stable horizontal position.
►Place the projector in a cool place, and ensure that there is sufficient ventilation.
►Do not place the projector any place where it may get wet.
CAUTION
►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s remote
sensor.
2
(15)
(20)
(30)
(35)
(41)
(46)
(51)
(61)
(76)
(101)
(127)
(152)
(177)
Connecting your devices
ENGLISH
Before connecting devices, please read the manuals for all the devices that you want to connect with
this projector, to make sure that the connection is proper and prepare the connectors needed. And
connect them properly according to the manuals.
AUDIO OUT
RGB OUT
RS-232C
RGB OUT
AUDIO OUT
HDMI
LAN
USB-A
PC
Remote
control
LAN
LASER
INDICATOR
LASER
INDICATOR
STANDBY/ON
STANDBY/ON
VIDEO
VIDEO
RGB
RGB
MY SOURCE/
DOC.CAMERA
MY SOURCE/
DOC.CAMERA
SEARCH
SEARCH
BLANK
BLANK
LASER
LASER
RGB1
HDMI
RGB
OUT
Y
CB/PB
VIDEO
ASPECT
ASPECT
PUSH ENTER
PUSH ENTER
CR/PR
PAGE UP
PAGE UP
ESC
ESC
AUDIO IN1
AUDIO IN2
Monitor
POSITION
POSITION
RGB2
MAGNIFY
MAGNIFY
ON
ON
G/Y B/CB/PB R/CR/PR
H
S-VIDEO
R
L
AUDIO IN3
R
L
AUDIO IN4
AUDIO OUT
REMOTE
CONTROL
PAGE DOWN
PAGE DOWN
MENU
MENU
RESET
RESET
AUTO
AUTO
PbyP
MY BUTTON
MY BUTTON
1
1
VOLUME
VOLUME
+
+
OFF
OFF
2
2
-
FREEZE
FREEZE
KEYSTONE
KEYSTONE
MUTE
MUTE
V
USB
CONTROL
RGB IN
Speakers
(with an
amplifier)
AUDIO IN
S-VIDEO OUT
R
L
AUDIO OUT
VIDEO OUT
R
L
AUDIO OUT
Y
CB/PB
CR/PR
COMPONENT VIDEO OUT
R
L
AUDIO OUT
VCR/DVD player
WARNING
►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION
►Turn off all devices and unplug their power cords prior to connecting them to
projector.
►Use appropriate accessory or designated cables. Ask your dealer about non-accessory
cables which may be required a specific length or a ferrite core by the regulations. For
cables with a core only at one end, connect the end with the core to the projector.
►Make sure that devices are connected to the correct ports.
3
Connecting power supply
1. Connect the connector of the power cord to the AC IN (AC
inlet) of the projector.
2. Firmly plug the power cord's plug into the outlet.
Connector of the
power cord
AC IN
to the outlet
WARNING
►Please use extra caution when connecting the power cord, as incorrect or faulty
connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult your
dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power cord.
The power outlet should be close to the projector and easily accessible. Remove the
power cord for complete separation.
• Never modify the power cord.
Turning on the power
1. Make sure that the power cord is firmly and correctly connected STANDBY/ON button
POWER indicator
to the projector and the outlet.
2. Remove the lens cover, and set the power switch to the ON
position (marked “ I ”).
The POWER indicator will light up in steady orange. Then
wait several seconds because the buttons may not function for
these several seconds.
3. Press the STANDBY/ON button on the projector or the remote
control.
The projection lamp will light up and the POWER indicator will
Power
switch
begin blinking in green. When the power is completely on, the
indicator will stop blinking and light in steady green.
LASER
INDICATOR
STANDBY/ON
VIDEO
RGB
MY SOURCE/
DOC.CAMERA
SEARCH
BLANK
LASER
ASPECT
PUSH ENTER
PAGE UP
ESC
PAGE DOWN
MENU
POSITION
AUTO
MAGNIFY
MY BUTTON
RESET
VOLUME
+
ON
1
OFF
2
-
FREEZE
KEYSTONE
MUTE
WARNING
►A strong light is emitted when the projector’s power is on. Do not look into the lens
of the projector or look inside of the projector through any of the projector’s openings.
NOTE
• When the AUTO ON in the OPTION menu is set to the TURN ON, and the power was turned
off by the power switch last time, turning the power switch on makes the projection lamp light
on without pushing the STANDBY/ON button. For more information, please see the “Operating
Guide” in the CD.
4
Adjusting the projector's elevator
Use the elevator feet to place the projector horizontally. Using the feet can also
tilt the projector in order to project at a suitable angle to the screen, elevating
the front side of the projector within 10 degrees.
This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is
adjustable while pulling up the elevator knob on the same side as it.
1. To loose an elevator foot, pull up the elevator knob on the same side as it.
ENGLISH
10°
2. Position the front side of the projector to the desired height.
3. Release the elevator knobs in order to lock the elevator feet.
4. To finely adjust, twist the foot.
WARNING
►Do not handle the elevator knobs without holding the projector, since the projector
may drop down.
►Do not tilt the projector other than elevating its front within 10 degrees using the
adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or
shortening the lifetime of consumables, or the projector itself.
Remote control
Laser pointer
The laser beam is emitted and the LASER INDICATOR lights while the LASER button is pressed.
The laser beam outlet
LASER INDICATOR
R
R
SE TO
LA ICA
IND
B
RG
/
RCE
SOU ERA
MY C.CAM
DO
EO
N
VID
Y/O
DB
AN
ST
CH
AR
SE
R
SE
LASER button
LA
K
AN
BL
CT
PE
AS
WN
DO
PAGE
TER
PUSH
EN
T
SE
RE
GE
PA
UP
NU
ME
C
ES
TO
AU
ION
MY
IFY
ME
LU
VO
N
SIT
PO
+
BUTTO
1
-
GN
MA
ON
TE
MU
2
KE
NE
TO
YS
F
OF
ZE
EE
FR
WARNING
►Never hit an eye with the laser beam, and use the laser pointer except to serve as
a pointer to a screen. The laser beam can cause vision problems, and also may cause
radiation exposure.
5
Remote control (continued)
Putting batteries
Please load the batteries before using the remote control.
1. Slide back and remove the battery cover.
2. Put the two AA batteries (HITACHI MAXELL, Part No.LR6 or R6P)
into the holder, according to the polarity markings (+) and (-) on the holder.
3. Put the battery cover back to its former state.
WARNING
►Always handle the batteries with care and use them only as directed. Improper use
may result in battery explosion, cracking or leakage, which could result in fire, injury
and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different types at the
same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. If the
leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
Buttons
(1) STANDBY/ON button
(2) VIDEO button
(3) RGB button
(4) MY SOURCE/DOC.CAMERA button
(5) SEARCH button
(6) BLANK button
(7) LASER button
(8) ASPECT button
(9) Lever switch : acting 3 functions as below.
Cursor button ▲ : to slide toward the side marked ▲.
Cursor button ▼ : to slide toward the side marked ▼.
ENTER button : to push down the center point.
(10) Cursor button ◄
(11) Cursor button ►
(12) PAGE UP button
(13) PAGE DOWN button
(14) ESC button
(15) MENU button
(16) RESET button
(17) POSITION button
(18) AUTO button
(19) MAGNIFY ON/OFF button
(20) MY BUTTON 1 button (21) MY BUTTON 2 button
(22) VOLUME +/- button
(23) FREEZE button
(24) KEYSTONE button
(25) MUTE button
6
LASER
INDICATOR
(1)
(2)
STANDBY/ON
VIDEO
RGB
MY SOURCE/
DOC.CAMERA
SEARCH
(6)
(8)
(10)
(12)
(14)
(17)
(18)
(19)
(21)
(23)
BLANK
LASER
ASPECT
PUSH ENTER
PAGE DOWN
PAGE UP
ESC
MENU
RESET
POSITION
AUTO
MAGNIFY
MY BUTTON
VOLUME
ON
1
+
OFF
2
-
FREEZE
KEYSTONE
MUTE
(3)
(4)
(5)
(7)
(9)
(11)
(13)
(15)
(16)
(20)
(22)
(24)
(25)
ASPECT
button
Displaying the picture
INPUT button
1. Make sure that the signal source is sending the signal to the
projector.
2. Use the VOLUME +/- buttons to adjust the volume. To have
the projector silent, press the MUTE button on the remote
control.
3. Press the INPUT button on the projector.
Each time you press the button, the projector switches its input
port in turn.
VOLUME +/- buttons
MUTE button
4. Press the ASPECT button on the remote control. Each time
you press the button, the projector switches the mode for
Zoom ring
Focus ring
aspect ratio in turn.
LASER
INDICATOR
STANDBY/ON
VIDEO
RGB
MY SOURCE/
DOC.CAMERA
SEARCH
LASER
ENGLISH
BLANK
ASPECT
PUSH ENTER
PAGE UP
PAGE DOWN
ESC
MENU
POSITION
AUTO
MAGNIFY
MY BUTTON
ON
1
RESET
VOLUME
+
OFF
2
-
FREEZE
KEYSTONE
MUTE
5. Use the zoom ring to adjust the screen size.
6. Use the focus ring to focus the picture.
Top
7. Use the vertical lens shift dial to shift the picture upward or
downward. It is recommended to adjust the picture upward.
2/5
8. Use the horizontal lens shift dial to shift the picture left or
right.
Lens shift cover
1/10
1/10
Turning off the power
1. Press the STANDBY/ON button on the projector or the remote
control.
The message “Power off?” will appear on the screen for about
5 seconds.
2. Press the STANDBY/ON button on the projector or the remote
control again while the message appears.
The projector lamp will go off, and the POWER indicator will
begin blinking in orange.
Then the POWER indicator will stop blinking and light in
steady orange when the lamp cooling is complete.
3. Make sure that the POWER indicator lights in steady orange,
and set the power switch to the OFF position (marked “O”).
The POWER indicator will go off. Attach the lens cover.
STANDBY/ON button
POWER indicator
LASER
INDICATOR
STANDBY/ON
VIDEO
RGB
MY SOURCE/
DOC.CAMERA
SEARCH
BLANK
LASER
ASPECT
PUSH ENTER
PAGE DOWN
PAGE UP
ESC
MENU
POSITION
AUTO
MAGNIFY
MY BUTTON
ON
1
RESET
VOLUME
+
OFF
2
-
FREEZE
KEYSTONE
MUTE
Power
switch
Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector on
again too soon could shorten the lifetime of some consumable parts of the projector.
WARNING
►Do not touch around the lamp cover and the exhaust vents during use or just after use,
since it is too hot.
7
Lamp
A lamp has finite product life. Using the lamp for long periods of time could cause the pictures
darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make
contact with your dealer and tell the lamp type number.
Type number = 456-8949H
Replacing the lamp
1. Turn the projector off, and unplug the power cord. Allow the
projector to cool for at least 45 minutes.
2. Prepare a new lamp.
If the projector is mounted on a ceiling, or if the lamp has
broken, also ask the dealer to replace the lamp.
In case of replacement by yourself,
3. Loosen the screw (marked by arrow) of the lamp cover and
then slide the lamp cover to the side to remove it.
4. Loosen the 3 screws (marked by arrow) of the lamp, and
slowly pick up the lamp by the handles.
5. Insert the new lamp, and retighten firmly the 3 screws of the
lamp that are loosened in the previous process to lock it in
place.
6. Slide the lamp cover back in place and firmly fasten the
screw of the lamp cover.
7. Turn the projector on and reset the lamp time using the
LAMP TIME item in the OPTION menu.
(1) Press the MENU button to display a menu.
(2) Point at the “Go to Advanced Menu …” in the menu
using the ▼/▲ button, then press the ► button.
(3) Point at the “OPTION” in the left column of the menu
using the ▼/▲button, then press the ► button.
(4) Point at the “LAMP TIME” using the ▼/▲ button, then
press the ► button. A dialog will appear.
(5) Press the ▲ button to select “RESET” on the dialog. It
performs resetting the lamp time.
The lamp cover
The handles
NOTE
• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about
the lamp.
8
Lamp (continued)
Lamp warning
HIGH TEMPERATURE
HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The lamp can break with a
loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
Note that each lamp has a different lifetime, and some may burst or burn out soon
after you start using them. In addition, when the bulb bursts, it is possible for shards of
glass to fly into the lamp housing, and for gas containing mercury to escape from the
projector’s vent holes.
• If the lamp should break (it will make a loud bang when it does),
Disconnect the
plug from the
power outlet
Unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass could
damage the projector’s internals, or cause injury during handling, so please
do not try to clean the projector or replace the lamp yourself.
Ventilate the room well, and make sure not to breathe the gas that comes
out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the
lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from a
ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards
will fall out when the cover is opened. In addition, working in high places
is dangerous, so ask your local dealer to have the lamp replaced even if the
bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose screws
could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible that there
are electrical problems elsewhere besides the lamp. If this happens, consult
your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to burst
during use.
• Using the lamp for long periods of time, could cause it dark, not to light up
or to burst. When the pictures appear dark, or when the color tone is poor,
please replace the lamp as soon as possible. Do not use old (used) lamps;
this is a cause of breakage.
► About disposal of a lamp: This product contains a mercury lamp; do not put it in
a trash. Dispose of it in accordance with environmental laws.
· For lamp recycling, go to www.lamprecycle.org (in the US).
· For product disposal, consult your local government agency or www.eiae.org (in the
US) or www.epsc.ca (in Canada).
For more information, ask your dealer.
9
ENGLISH
HIGH VOLTAGE
Air filter
Please check and clean the air filter periodically. When the indicators or a message prompts you to
clean the air filter, comply with it as soon as possible. The air filter has two kinds of filters inside.
Replace the filters when they are damaged or too soiled. To prepare the new filters, make contact
with your dealer and tell the following type number.
Type number = MU05661
When you replace the lamp, please replace the air filter. An air filter of
specified type will come together with a replacement lamp for this projector.
the projector off, and unplug the power cord. Allow the projector
1.Turn
to sufficiently cool down.
2.Use a vacuum cleaner on and around the filter cover.
3.Pull the filter cover knobs while lifting it, to take the filter unit off.
a vacuum cleaner for the filter vent of the projector and both sides
4.Use
of the filter unit.
Filter cover
Filter cover knobs
Filter unit
If the filters are damaged or too soiled, replace them according to the following
procedure number 5 to 7. Otherwise, please jump to the procedure number 8.
the filter frame’s knob up while holding the filter cover to remove
5.Pull
the filter frame, then take the filters out.
new filters where former filters were. Put the larger meshed filter
6.Set
into a filter cover first. Then put the finer meshed filter on the larger
Filter frame
Filter (finer meshed)
meshed one.
7.Put the filter frame back where it was.
8.Put the filter unit back into the projector.
Turn the projector on and reset the filter time using the FILTER TIME
9.item
in the EASY MENU
Filter (larger meshed)
Filter cover
(1) Press the MENU button to display a menu.
(2) Point at the “FILTER TIME” using the ▼/▲ button, then press the ► button. A dialog will appear.
(3) Press the ▲ button to select RESET on the dialog. It performs resetting the filter time.
WARNING
►Before taking care of the air filter, make sure the power cable is not plugged in, then allow the
projector to cool sufficiently.
►Use only the air filter of the specified type. Do not use the projector without the air filter or the filter
cover. It could result in a fire or malfunction to the projector.
►Clean the air filter periodically. If the air filter becomes clogged by dust or the like, internal temperatures
rise and could cause a fire, a burn or malfunction to the projector.
NOTE • Please reset the filter time only when you have cleaned or replaced the air filter, for a
suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or turn off the
projector, to prevent the internal heat level rising.
10
Internal clock battery
Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has
stopped, please replace the battery according to the following procedures.
ENGLISH
1. Turn the projector off, and unplug the power cord. Allow the
projector to cool sufficiently.
2. After making sure that the projector has cooled adequately, slowly
turn over the projector, so that the bottom is facing.
3. Turn the battery cover fully in the direction indicated “OPEN”
using a coin or the like, and pick the cover up to remove it.
4. One of two kinds of clock battery holder, A or B shown to the
right, is inside the battery cover.
Battery Cover
90°
OPEN
OPEN
CLOSE
OPEN
CLOSE
OPEN
CLOSE
For B holder:
Press the metal claw of the battery holder putting a finger lightly
on the battery since it may pop out of the holder. Then the battery
will come up. Remove the battery.
5. Replace the battery with a newHITACHI MAXELLL, Part No.
CR2032 or CR2032H.
Slide the battery in under the plastic claw, and push it into the
holder until it clicks.
6. Replace the battery cover in place, then turn it in the direction
indicated “CLOSE” using such as coins, to fix.
OPEN
CLOSE
For A holder:
Pry up the battery using a flathead screwdriver or the like to take it out.
While prying it up, put a finger lightly on the battery since it may pop out
of the holder.
OPEN
CLOSE
CLOSE
90°
NOTE
• If the battery is inserted upside down in the B holder, it might be difficult to remove. If that happens, take
following measures:
(1) Remove the battery cover and turn the projector's upside up.
(2) While lifting the side of the projector closer to the lens, press the metal claw of the battery holder.
The battery will fall out of the holder, so be careful not to lose it.
WARNING
►Always handle the batteries with care and use them only as directed. Battery may explode if
mistreated. Do not recharge, disassemble or dispose of in fire.
And also improper use may result in cracking or leakage, which could result in fire, injury and/or
pollution of the surrounding environment.
• Be sure to use only the batteries specified.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets. If swallowed consult a physician immediately for
emergency treatment.
• Do not short circuit or solder a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage
adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
11
Using the CD manual
The detailed manuals for this product are written into the CD titled “User’s Manual
(detailed)” which came with this product. Before using the CD, read the following to
ensure the proper use.
System requirements
For using the CD manual, the following system is required.
OS: Microsoft® Windows® 98, Windows® 98SE, Windows NT® 4.0,
Windows®:
Windows® Me, Windows® 2000/Windows® XP, or the later
CPU: Pentium® processor 133MHz / Memory: 32MB or more
Macintosh®: OS: Mac OS® 10.2 or the later
CPU: PowerPC® / Memory: 32MB or more
CD-ROM drive:
4x CD-ROM drive
Display:
256 color / 640x480 dots resolution
Applications:
Microsoft® Internet Explorer® 4.0 and
Adobe® Acrobat® Reader® 4.0 or the later
How to use the CD
1. Insert the CD into the CD-ROM drive of your computer.
2. When using it on the Macintosh® system, start the web browser by the following.
(1) Double-click on the “Projectors” icon displayed on the computer’s desktop.
(2) Then click on the “main.html” file.
When using it on the Windows® system, the web browser automatically starts.
3. The web browser displays the initial window of the manual.
On the window, select the model name of your projector, and the language you want to
read the manuals with. The manual in the selected language will open.
NOTE
• The information in the CD is subject to change without notice.
• The manufacturer assumes no responsibility for any obstacle and defect to hardware
and software of your computer as a result of the use of the CD.
• The reproduction, transfer or copy of all or any part of the information in the CD is not
permitted without express written consent.
CAUTION
►Only use the CD in a computer’s CD drive. Never insert the CD into a CD drive of
a non-computer device such as an audio device. Inserting the CD into an incompatible
CD drive may produce a loud noise, which may result in damage to ears and speakers.
►While the CD is not used, put it into its envelope. Avoiding the CD from direct rays, a
high temperature, and high humidity. Be careful not to scratch or press the CD.
12
Regulatory notices
About Electro-Magnetic Interference
ENGLISH
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
In Canada
This Class A digital apparatus complies with Canadian ICES-003.
In the US and places where the FCC regulations are applicabl
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to case harmful interference in which case the user will be required to correct the
interference at his own expense.
INSTRUCTIONS TO USERS:Some cables have to be used with the core set. Use
the accessory cable or a designated type cable for the connection. For cables that have a
core only at one end, connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
13
Regulatory notices (continued)
About Waste Electrical and Electronic Equipment
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries or accumulators included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a
heavy metal content of more than 0.0005% Mercury or more than, 0.002%
Cadmium, or more than 0.004% Lead.
14
Specifications
Item
Liquid
Crystal
Panel
Liquid crystal projector
Panel size
2.0cm (0.79 type)
Drive system
TFT active matrix
Pixels
ENGLISH
Product name
Specifications
1,470,000 pixels (1400 horizontal x 1050 vertical)
Lens
Zoom lens F=1.7 ~ 1.9 f=24 ~ 29 mm (approx.)
Lamp
275W UHB
Audio output
4W x 2
Power supply
AC 100-120V/5.0A, AC220-240V/2.1A
Power consumption
460W
Temperature range
5 ~ 35°C (Operating)
Weight (mass)
7.1kg (approx.)
Ports
RGB1 ..................................................... D-sub 15 pin mini x
RGB2 G/Y, B/CB/PB, R/CR/PR, H, V .............................BNC x
S-VIDEO ......................................................mini DIN 4 pin x
VIDEO ........................................................................ RCA x
Y, CB/PB, CR/PR (component video) ............................ RCA x
HDMI ........................................................................ HDMI x
AUDIO IN1 ....................................................... Stereo mini x
AUDIO IN2 ....................................................... Stereo mini x
AUDIO IN3 R/L ........................................................... RCA x
AUDIO IN4 R/L ........................................................... RCA x
RGB OUT ............................................... D-sub 15 pin mini x
AUDIO OUT ..................................................... Stereo mini x
USB ...................................................................... USB (B) x
REMOTE CONTROL ....................................... Stereo mini x
CONTROL ....................................................... D-sub 9 pin x
LAN ............................................................................ RJ45 x
1
5
1
1
3
1
1
1
2
2
1
1
1
1
1
1
139
Size
154
319
418 (W) x 139 (H) x 319 (D) mm (approx.)
418
[unit: mm]
Optional parts
Lamp: 456-8949H
Air filter: MU05661
* For more information, please consult your dealer.
15
Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound) should occur, stop
using the projector immediately. Otherwise if a problem occurs with the projector, first refer to the
“Troubleshooting” of the “Operating Guide” in the CD and run through the suggested checks.
If this does not resolve the problem, please consult your dealer or service company. They will tell
you what warranty condition is applied.
Please check the following web address where you may find the latest information for this projector.
www.dukcorp.com/av
NOTE
• The information in this manual is subject to change without notice.
• The manufacture assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transfer or copy of all or any part of this document is not permitted without
express written consent.
TRADEMARK ACKNOWLEDGMENT
• Microsoft® and Internet Explorer® Windows®, Windows NT® are registered trademark
of Microsoft Corporation.
• PowerPC® is a registered trademark of International Business Machines Corporation.
• Macintosh® and Mac OS® are registered trademark of Apple Inc.
• Adobe® and Acrobat®, Reader® are registered trademarks of Adobe System Incorporated.
• Pentium® is a registered trademark of Intel Corporation.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
All other trademarks are the properties of their respective owners.
Download PDF