STRATOS S810-X52L manual

STRATOS S810 Series
S810-X52L
Ultra Dense High Computing
Multi-node 2U Server
User's Guide
Document Version: 1.2.0
CONVENTIONS
Conventions
Several different typographic conventions are used throughout
this manual. Refer to the following examples for common
usage.
Note:
Highlights general or useful information and tips.
Bold type face denotes menu items, buttons and application
names.
Italic type face denotes references to other sections, and the
names of the folders, menus, programs, and files.
<Enter> type face denotes keyboard keys.
!
!
WARNING!
Warning information appears before the text it references and
should not be ignored as the content may prevent damage to the
device.
CAUTION!
CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES, SIMILAR TO
NOTES AND WARNINGS. CAUTIONS, HOWEVER, APPEAR IN CAPITAL LETTERS AND CONTAIN VITAL HEALTH AND SAFETY INFORMATION.
Important:
Indicates information that is important to know for the proper completion of a procedure, choice of an option, or completing a task.
XVI
ACRONYMS
Acronyms
TERM
A/D
DEFINITION
ACPI
Advanced Configuration and Power Interface
ASF
Alerting Standard Forum
Asserted
Basic Input/Output System
BIST
Built-In Self Test
BMC
At the heart of the IPMI architecture is a microcontroller
called the Baseboard management controller (BMC)
Bridge
Circuitry connecting one computer bus to another, allowing an agent on one to access the other
BSP
Bootstrap processor
Byte
8-bit quantity
CLI
Command Line Interface
CPU
DTC
Active-high (positive true) signals are asserted when in
the high electrical state (near power potential). Activelow (negative true) signals are asserted when in the low
electrical state (near ground potential).
BIOS
CMOS
Deasserted
Analog to Digital
EEPROM
FRU
Field Replaceable Unit
1024 MB.
GPIO
General Purpose Input/Out
HSC
Hot-Swap Controller
Hz
Hertz (1 cycle/second)
I 2C
Inter-Integrated Circuit bus
Internet Assigned Numbers Authority
IBF
Input buffer
ICH
I/O Controller Hub
ICMB
Intelligent Chassis Management Bus
IERR
Internal Error
IP
IPMB
XVII
Electrically Erasable Programmable Read-Only Memory
Emergency Management Port
IANA
Central Processing Unit
Data Transfer Controller
EMP
GB
In terms of this specification, this describes the PC-AT
compatible region of battery-backed 128 bytes of memory, which normally resides on the baseboard
A signal is deasserted when in the inactive state. Activelow signal names have “_L” appended to the end of the
signal mnemonic. Active-high signal names have no “_L”
suffix. To reduce confusion when referring to active-high
and active-low signals, the terms one/zero, high/low, and
true/false are not used when describing signal states.
Internet Protocol
Intelligent Platform Management Bus
ACRONYMS
IPMI
Intelligent Platform Management Interface
NM
Node Management
ITP
In-Target Probe
OBF
Output buffer
KB
1024 bytes.
OEM
Original Equipment Manufacturer
KCS
Keyboard Controller Style
Ohm
Unit of electrical resistance
KVM
Keyboard, Video, Mouse
PDB
Power Distribution Board
LAN
Local Area Network
PEF
Platform Event Filtering
LCD
Liquid Crystal Display
PEP
Platform Event Paging
LCT
Lower Critical Threshold
LED
Light Emitting Diode
POH
Power-On Hours
LNCT
Lower Non-Critical Threshold
POST
Power-On Self Test
LNRT
Lower Non-Recoverable Threshold
PWM
Pulse Width Modulation
LPC
Low Pin Count
RAC
Remote Access Card
LSI
Large Scale Integration
RAM
Random Access Memory
LUN
Logical Unit Number
MAC
Media Access Control
MB
PERR
RMCP
1024 KB
MD2
Message Digest 2 – Hashing Algorithm
MD5
Message Digest 5 – Hashing Algorithm – Higher Security
Ms
Milliseconds
Mux
Multiplexer
NIC
Network Interface Card
NMI
Nonmaskable Interrupt
Remote Management Control Protocol
ROM
Read Only Memory
RTC
Real-Time Clock. Component of the chipset on the baseboard.
RTOS
Real Time Operation System
SCI
Serial Communication Interface
SDC
SCSI Daughter Card
SDR
Sensor Data Record
SEEPROM
XVIII
Parity Error
Serial Electrically Erasable Programmable Read-Only
Memory
ACRONYMS
SEL
System Event Log
SERR
System Error
SMBus
A two-wire interface based on the I2C protocol. The
SMBus is a low-speed bus that provides positive
addressing for devices, as well as bus arbitration
SMI
Server Management Interrupt. SMI is the highest priority
nonmaskable interrupt
SMM
Server Management Mode
SMS
Server Management Software
SNMP
SOL
UART
Simple Network Management Protocol
Serial Over LAN
Universal Asynchronous Receiver/Transmitter
UCT
Upper Critical Threshold
UDP
User Datagram Protocol
UNCT
Upper Non-Critical Threshold
UNRT
Upper Non-Recoverable Threshold
WDT
Watchdog Timer
Word
16-bit quantity
XIX
SAFETY INFORMATION
Safety Information
Important Safety Instructions
modems attached to the server before opening it. Otherwise,
personal injury or equipment damage can result.
Read all caution and safety statements in this document before
performing any of the instructions.
Electrostatic discharge (ESD) and ESD protection: ESD can
damage drives, boards, and other parts. We recommend that
you perform all procedures in this chapter only at an ESD workstation. If one is not available, provide some ESD protection by
wearing an antistatic wrist strap attached to chassis ground any
unpainted metal surface on the server when handling parts.
Warnings
Heed safety instructions: Before working with the server,
whether using this manual or any other resource as a reference, pay close attention to the safety instructions. Adhere to
the assembly instructions in this manual to ensure and maintain
compliance with existing product certifications and approvals.
Use only the described, regulated components specified in this
manual. Use of other products / components will void the UL
listing and other regulatory approvals of the product and will
most likely result in non-compliance with product regulations in
the region(s) in which the product is sold.
ESD and handling boards: Always handle boards carefully.
They can be extremely sensitive to electrostatic discharge
(ESD). Hold boards only by their edges. After removing a board
from its protective wrapper or from the server, place the board
component side up on a grounded, static free surface. Use a
conductive foam pad if available but not the board wrapper. Do
not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic
encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that can be gripped with fingertips
or with a pair of fine needle nosed pliers. If the jumpers do not
have such a tab, take care when using needle nosed pliers to
remove or install a jumper; grip the narrow sides of the jumper
with the pliers, never the wide sides. Gripping the wide sides
can damage the contacts inside the jumper, causing intermittent
problems with the function controlled by that jumper. Take care
to grip with, but not squeeze, the pliers or other tool used to
remove a jumper, or the pins on the board may bend or break.
System power on/off: The power button DOES NOT turn off
the system AC power. To remove power from system, you must
unplug the AC power cord from the wall outlet. Make sure the
AC power cord is unplugged before opening the chassis, adding, or removing any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power, telephone, and communication cables. Turn off the server and disconnect the
power cord, telecommunications systems, networks, and
XX
SAFETY INFORMATION
XXI
REVISION HISTORY
Revision History
Refer to the table below for the updates made to this manual.
DATE
CHAPTER
UPDATES
Copyright
Disclaimer
Copyright © 2014 Quanta Computer Inc. This publication,
including all photographs, illustrations and software, is protected under international copyright laws, with all rights
reserved. Neither this manual, nor any of the material contained
herein, may be reproduced without the express written consent
of the manufacturer. All trademarks and logos are copyrights of
their respective owners.
The information in this document is subject to change without
notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for
any particular purpose. Furthermore, the manufacturer reserves
the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Version 1.2 / 1/24/14
For the latest information and updates please refer to
www.QuantaQCT.com
All the illustrations in this technical guide are for reference only
and are subject to change without prior notice.
XXII
About the Server
Chapter 1
ABOUT THE SERVER
INTRODUCTION
1.1 Introduction
This manual is written for system technicians who are responsible for troubleshooting, upgrading, and repairing the server chassis.
This document provides an overview of the hardware features of the chassis, troubleshooting information, and instructions on how to
add and replace components of the multi-node server series.The document also provides information on the BIOS, and Baseboard
Management Controller (BMC).
For the latest version of this manual, see www.quantaqct.com.
System Features
Note:
The system comprises a 2U/30.5” long chassis using a standard SSI mainboard. Some of the major features are as follows:






S810-X52L supports power in the range of 220V - 240V.
Chipset: Intel® C600 series, upgradable ROM kit support.
Processors (x2): Intel® Xeon E5-2600/E5-2600 v2 series
processors.
PCI-E x16: (1) PCI-E x16 G3 riser slot for low-profile card,
(1) PCI-E x16 G3 slot for Quanta LSISAS/RAID or 10 GbE
SFP+ Mezzanine card.
Memory: Up to sixteen DIMM slots are available. DDR3
800/1066/1333/1600 MHz UDIMM, RDIMM, and LRDIMM
memory is supported.
Storage: Up to six 2.5" SATA/SAS hot-plug HDDs or three
3.5" SATA/SAS hot-plug HDDs per node
Network: Intel® Powerville I350 GbE or Twinville X540
10G BASE-T RJ45 dual-port on board
1-1
ABOUT THE SERVER
SYSTEM FEATURES
Table 1-1: S810-X52L SKU
S810-X52L 2.5"
( 1 TO 1 1G SKU)
S810-X52L
S810-X52L 2.5"
( 1 TO 1 10G SKU)
S810-X52L 3.5"
( 1 TO 1 1G SKU)
S810-X52L 3.5"
( 1 TO 1 10G SKU)
X5 (2U chassis)
774.7mm x 447mm x 87.3mm
 30.5" x 17.6" x 3.44"

Form Factor ( L x W x H )

165mm x 492.3mm
6.5" x 19.38" (half-width)
 Up to 4 independent nodes in a 2U chassis

MB size (W x L )

Processor
(2) Intel® Xeon® processor E5-2600/E5-2600 v2 family per node, up to 130W
Chipset
Intel® C602 (Patsburg A)
[Intel® SAS controller]

Intel
®
C602 (Patsburg A) upgrade ROM #5 (optional)
®
SAS Controller
Memory
 Intel C602 (Patsburg A) upgrade ROM #6 (optional)
or
[LSI SAS controller]
 Quanta LSISAS 2008 Mezzanine card (optional)
 Quanta LSISAS 2108 Mezzanine card (optional)


DDR3 800/1066/1333/1600 MHz x 16
ECC UDIMM/RDIMM/LRDIMM slots per node, up to 512 GB
Storage
2.5" SATA/SAS (6* 3Gb SCU) hot-plug HDD per node x 6
 USB Flash Module for OS installation per node x 1
(optional)
HDD Backplane
1 to 1

PCIe Expansion Slot


[Intel® SAS controller]
Intel® C602 (Patsburg A) upgrade ROM #1 (optional)
 Intel® C602 (Patsburg A) upgrade ROM #2 (optional)
or
[LSI SAS controller]
 Quanta LSISAS 2008 Mezzanine card (optional)
 Quanta LSISAS 2108 Mezzanine card (optional)

3.5" SATA/SAS(3* 3Gb SCU) hot-plug HDD per node x 3
 USB Flash Module for OS installation per node x 1
(optional)

PCIe x16 G3 riser slot for low-profile card per node x 1
PCIe x16 G3 slot for Quanta LSISAS/RAID or 10GbE SFP+ mezzanine card per node x 1
1-2
ABOUT THE SERVER
SYSTEM FEATURES
Table 1-1: S810-X52L SKU (Continued)
S810-X52L 2.5"
( 1 TO 1 1G SKU)
S810-X52L
S810-X52L 2.5"
( 1 TO 1 10G SKU)
[Intel®SW RAID] (Optional)


SW RAID Options

®
Intel C602 (Patsburg A) upgrade ROM #9 SATA RAID
0/1/10/5 for SCU




Intel® C602 (Patsburg A) upgrade ROM #6 SAS RAID 0/
1/10/5 for SCU

Management Port
(1) Dedicated 10/100 BASE-T RJ45 management port per node
Integrated Graphics BMC
Aspeed AST2300 8MB DDR3 Video memory

Rear I/O



Intel® C602 (Patsburg A) upgrade ROM #1 SAS RAID 0/
1/10 for SCU
Intel® C602 (Patsburg A) upgrade ROM #2 SAS RAID 0/
1/10/5 for SCU
Quanta LSISAS2108 PD-8 mezzanine card for RAID 0/1/10/5 (optional)
Quanta LSISAS2108 PD-8 mezzanine card + LSI RAID 6 Key for RAID 0/1/10/5/6/50/60 (optional)
Network

Intel® C602 (Patsburg A) RSTe SATA RAID 0/1/10/5
or
[LSI SW RAID]
Quanta LSISAS 2008 mezzanine card for RAID 0/1/10
(2) Intel® Powerville I350
GbE RJ45 ports on board
per node
 (1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)

S810-X52L 3.5"
( 1 TO 1 10G SKU)
[Intel®SW RAID]
Intel® C602 (Patsburg A) upgrade ROM #5 SAS RAID 0/
1/10 for SCU
or
[LSI SW RAID]
Quanta LSISAS 2008 mezzanine card for RAID 0/1/10
HW RAID Options
S810-X52L 3.5"
( 1 TO 1 1G SKU)
(2) Intel® Twinville X540
10G BASE-T RJ45 ports
on board per node
 (1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)

(2) USB 2.0 ports per node
(1) VGA per node
(1) RS232 Serial port per node
(2) GbE or 10G BASE-T RJ45 ports per node
(1) 10/100 BASE-T RJ45 management port per node
1-3
(2) Intel® Powerville I350
GbE RJ45 ports on board
per node
 (1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)

(2) Intel® Twinville X540
10G BASE-T RJ45 ports
on board per node
 (1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)

ABOUT THE SERVER
SYSTEM FEATURES
Table 1-1: S810-X52L SKU (Continued)
S810-X52L 2.5"
( 1 TO 1 1G SKU)
S810-X52L
Power Supply
S810-X52L 2.5"
( 1 TO 1 10G SKU)
S810-X52L 3.5"
( 1 TO 1 1G SKU)
(1) 1400W high efficiency PSU, 200-240VAC 50/60Hz
 (1) 1400W high efficiency redundant PSU, 200-240VAC 50/60Hz (optional)

TPM
No
RoHS
Yes
Intel Node Management
support
No
System Management
IPMI v2.0 Compliant, on board "KVM over IP" support
1-4
S810-X52L 3.5"
( 1 TO 1 10G SKU)
ABOUT THE SERVER
PACKAGE CONTENTS
1.1 Package Contents
The following list includes the package components for a 2
node configuration:

1 x 2U server chassis

2 x Mainboard modules

2 x Dummy modules

4 x Processor heatsinks

16 x Dummy DIMMs

1 x Power supply

1 x Power cord

Utility CD (Technical Guide included)

Rail kit
Important:
Server configurations may vary. Confirm your sales representative
for the exact items included in your order.
1-5
ABOUT THE SERVER
A TOUR OF THE SYSTEM
1.1 A Tour of the System
The S810-X52L is available as a 2.5” HDD or a 3.5” HDD system. The following illustrations show the major component parts of
these two variants.
2.5” HDD System
8
Table 1-2: 2.5” System Component Overview
No.
9
Description
1
PSUs
2 Power supply units (PSU)
2
Chassis
System chassis
3
Node
controller
Controls and LEDs for system management
4
2.5” HDDs
24 2.5” hard disk drive (HDD) cage
5
Fans
Fan module cage
6
PDB boards
Top and Bottom PDB (Power Distribution Board)
7
Top cover
extension
Top cover extension
2
8
Top cover
System top cover with handle
3
9
MB modules
4 hot-swap mainboard modules
7
1
6
Item
5
4
Figure 1-1. 2.5” System Component Overview
1-6
ABOUT THE SERVER
3.5” HDD SYSTEM
3.5” HDD System
Table 1-3: 3.5” System Component Description
No.
7
8
6
1
5
2
3
4
Figure 1-2.
3.5” System Component Description
1-7
Item
Description
1
PSUs
2 Power supply units (PSU)
2
Chassis
System chassis
3
Node
controller
Controls and LEDs for system management
4
3.5” HDDs
12 3.5” hard disk drive (HDD) cage
5
Fans
Fan module cage
6
PDB boards
Top and Bottom PDB (Power Distribution Board)
7
Top cover
System top cover with handle
8
MB modules
4 hot-swap mainboard modules
ABOUT THE SERVER
SYSTEM FRONT FEATURES
System Front Features
Node Control Panels
The node control panels manage specific 2.5” and 3.5” HDD
groups as indicated in the following illustrations.
1
Note:
Each HDD drive group serves a designated mainboard. See “System Rear Features” on page 11 for information on mainboards.
2.5” HDD Group Configuration
2
Figure 1-3.
System Front Features
Note:
2.5" SKU shown (Figure 1-3)
Table 1-4: System Front Features
No
Feature
Figure 1-4.
Description
1
Node
control
panels
4 node control system
2
HDD bays
2.5” or 3.5” HDD array
2.5” HDD Configuration
3.5” HDD Group Configuration
MB1 HDD BAY
MB2 HDD BAY
MB3 HDD BAY
MB4 HDD BAY
1
2
3
4
Figure 1-5.
1-8
3.5” HDD Configuration
ABOUT THE SERVER
SYSTEM FRONT FEATURES
Node Control Panel Features
Table 1-5: Node Control Panel Features (Continued)
No
1
2
3
4
5
6
7
8
1
2
3
Feature
Function
3
MB2 Power
Button
Power On/Off for MB2
4
MB2 ID
Button
MB2 module ID LED control
5
MB3 Power
Button
Power on/off for MB3
6
MB3 ID
Button
MB3 module ID LED control
7
MB4 Power
Button
Power on/off for MB4
8
MB4 ID
Button
MB4 module ID LED control
4
Note:
MB1 HDD BAY
MB2 HDD BAY
Figure 1-6.
MB3 HDD BAY
The buttons are functional LEDs. The numbered items in the following tables represent the same item in the preceding figure.
MB4 HDD BAY
Node Control Panel Features
Table 1-5: Node Control Panel Features
No
Feature
Function
1
MB1 Power
Button
Power on/off for MB1
2
MB1 ID
Button
MB1 module ID LED control
1-9
ABOUT THE SERVER
SYSTEM HDD SKU INTRODUCTION
System HDD SKU Introduction
Table 1-6: Node Control Panel LED Description
No
Feature
Function
Status
Description
1
MB1 Power
Button LED
Green LED:
On
DC on
3
MB2 Power
Button LED
Green LED:
Off
DC off
5
MB3 Power
Button LED
Amber LED:
Blinking
DC off and
fault
7
MB4 Power
Button LED
2
MB1 ID
Button
4
MB2 ID
Button
6
MB3 ID
Button
8
MB4 ID
Button
Power button
LED function
Green LED/
Amber LED:
alternate
blinking
ID button LED
function
The multi-node systems are available as a 2.5” or 3.5” SKU.
Within the HDD array, the HDD enumeration is as follows:
2.5” HDD Configuration
0
1
2
3
4
5
0
1
2
3
4
5
0 1
2
3
4
5
0 1
2
3
4
DC on and
fault
MB1 HDD BAY
Blue LED:
Blinking
Select mode
Blue LED: Off
Normal
mode
MB2 HDD BAY
Figure 1-7.
MB3 HDD BAY
MB4 HDD BAY
2.5” HDD Configuration
3.5” HDD Configuration
0
0
0
0
1
1
1
1
2
2
2
2
MB1 HDD BAY
MB2 HDD BAY
MB3 HDD BAY
Note:
The numbered items in “Node Control Panel LED Description” are
a direct correlation to “Node Control Panel Features”.
Figure 1-8.
1-10
MB4 HDD BAY
3.5” HDD Configuration
5
ABOUT THE SERVER
SYSTEM REAR FEATURES
System Rear Features
S810-X52L Module I/O Features
S810-X52L System Rear
!
WARNING!
Mainboard combinations other than S810-X52L are
not supported.
1 2
MB 3
TOP PSU
MB 1
MB 4
BOTTOM PSU
MB 2
3
Figure 1-10.
4
5
6
7
S810-X52L Module I/O Features
Table 1-7: S810-X52L Module I/O Features
Figure 1-9.
No
S810-X52L System Rear
The S810-X52L system rear consists of four mainboard modules and two power supply units. Dummy modules are installed
to maintain proper airflow in the event that mainboard slots are
not fully populated.
1-11
Feature
Description
1
USB port
2 USB ports (2.0 compliant)
2
Rear ID LED
ID identification
3
Serial port
Connect serial devices to this port
4
VGA port
Connect a monitor to this port
5
Dedicated
Management
Port
10/100 BASE-T RJ45 management port
6
NIC 2
GbE or 10G BASE-T RJ45 port
7
NIC 1
GbE or 10G BASE-T RJ45 port
8
Power button
On/Off power to the module
8
ABOUT THE SERVER
SYSTEM REAR FEATURES
S810-X52L Module I/O LED Description
Table 1-8: S810-X52L Module I/O LED Description (Continued)
No
Table 1-8: S810-X52L Module I/O LED Description
No
2
Feature
ID ED L
Right
5,6
NIC1 & 2
LEDs (see
“LAN LEDs”)
Left
Status
Feature
Description
Blue On
Identify module by
BMC Web UI
Blue
Blinking
Identify module by
PWR button
Off
Normal mode
Off
No link
Green On
Link, no access
Green
Blinking
Link, access
Off
No link / link, access
10 Mbps
Green On
Link, access 100 Mbps
Amber On
Link, access 1000
Mbps
Right
7
Remote
Management
port LEDs
Left
1-12
Status
Description
Off
No link, no access
Green Off
Link, no access
Amber On
Link, no access
Green On
Link, access 10 Mbps
Amber On
Link, access 100 Mbps
Off
No link / link, no
access
Green
Blinking
Link, access
ABOUT THE SERVER
SYSTEM REAR FEATURES
LAN LEDs
HDD LED
The system mainboard has one I350 or X540 (optional) Ethernet controller and two 1GbE or 10GbE (optional) ports. Each
RJ45 connector has two built-in LEDs. See the following illustration and table for details.
Table 1-10: HDD LED Description
SGPIO LED Pattern
Slot/Device States (RAID States)
Activity
Link
PIN 1
Location
Identification
Status
LED
(Green)
Status
LED
(Amber)
Fault LED
(Red)
Active LED (Deep
Green)
Slot Empty
n/a
Off
Off
Off
Identify
n/a
On
Off

Fail
n/a
Rebuild
n/a
Device Online
On
Figure 1-11. RJ45 LAN Connector
Table 1-9: 1 GbE and 10 GbE LED Description
10 GbE Chip Onboard
1 GbE Chip Onboard
Link
Activity
Link
Activity
10 GbE LED
Green
Green
Blinking
N/A
N/A
1 GbE LED
Amber
Green
Blinking
Amber
Green Blinking
100M
Off
Green
Blinking
Green
Green Blinking
1-13
HDD Access
When HDD R/W
access, the
Off
On
active LED is On.
On 1 sec./ Off 1 sec./
No R/W access,
Off 1 sec. On 1 sec.
the active LED is
Off.
 Active LED control by HDD.
 When rebuild
n/a
Off
completed Identify/Fault, Status/
Fault LED will
return to green.
ABOUT THE SERVER
POWER SUB-SYSTEM
Power Sub-System
PSU LED
1
MB 3
TOP PSU
MB 1
MB 4
BOTTOM PSU
MB 2
Figure 1-12. PSU to Mainboard Module Description
!
WARNING!
Figure 1-13. PSU LED
Mainboard combinations other than S810-X52L are
not supported.
Table 1-12: PSU LED Description
A system has two modular Power Supply Units (PSU). Both
PSU’s are directly connected to the Power Distribution Boards
(PDBs), the HDD backplane, and middle plane allowing each
PSU to individually provide power for all mainboards (MB1 to
MB4).
The power supply units used for each model are:
Table 1-11: Power Supply Units by Model
Model
S810-X52L
PSU
2 x 1400W redundant PSU
AC Input
220V
1-14
No
Feature
1
PSU ED L
Status
Description
Green
Normal operation
Yellow
Fault
ABOUT THE SERVER
COOLING SUB-SYSTEM
Cooling Sub-System
Fans may spin for some time after the system has been powered off. Allow time for the fans to stop rotating before handling
system components.
1
Figure 1-14. Cooling Sub System
Table 1-13: Fan Cooling System
No
Feature
1
Fan cooling
system
Description
A metal frame holding fan modules
1-15
Installation and Assembly Safety
Instructions
Chapter
Chapter
INSTALLATION AND ASSEMBLY SAFETY INSTRUCTIONS
INSTALLATION ASSEMBLY SAFETY INSTRUCTIONS
2.1 Installation Assembly Safety Instructions
Guidelines
The power supply in this product contains no user-serviceable parts.
Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product
with more than one power supply will have a separate AC power cord for each supply.
The power button on the system does not turn off system AC power.
To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power
supply.
The power cord(s) is considered the disconnect device to the main (AC) power. The socket outlet that the
system plugs into shall be installed near the equipment and shall be easily accessible.
2-1
INSTALLATION AND ASSEMBLY SAFETY INSTRUCTIONS
GUIDELINES
SAFETY STEPS: Whenever you remove the chassis covers toaccess the inside of the system, follow these
steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall outlets.
4. Label and disconnect all cables connected to I/O connectors or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap attached to
chassis ground of the system-any unpainted metal surface-when handling components.
6. Do not operate the system with the chassis covers removed.
A microprocessor and heat sink may be hot if the system has been running. Also, there may be sharp pins
and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves.
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Dispose of used batteries according to manufacturer's instructions.
2-2
INSTALLATION AND ASSEMBLY SAFETY INSTRUCTIONS
GUIDELINES
The system is designed to operate in a typical office environment.
Choose a site that is:

Clean and free of airborne particles (other than normal room dust).

Well ventilated and away from sources of heat including direct sunlight.

Away from sources of vibration or physical shock.

Isolated from strong electromagnetic fields produced by electrical devices.



In regions that are susceptible to electrical storms, we recommend you plug your system into a surge
suppressor and disconnect telecommunication lines to your modem during an electrical storm.
Provided with a properly grounded wall outlet.
Provided with sufficient space to access the power supply cord(s), because they serve as the product's
main power disconnect.
WARNING!
The server system is safety certified as rack-mounted equipment for use in a server room or computer room,
using the customer rack kit.
The rail racks are designed to carry only the weight of the server system. Do not place additional load onto
any rail-mounted equipment.
System rack kits are intended to be installed in a rack by trained service technicians.
Heavy object. Indicates two people are required to safely handle the system.
2-3
Safety Information
Chapter
Chapter
SAFETY INFORMATION
SERVER SAFETY INFORMATION
3.1 Server Safety Information
To reduce the risk of bodily injury, electrical shock, fire, and
equipment damage, read this document and observe all warnings and precautions in this guide before installing or maintaining your server product.
symbols may be used throughout the documentation and may
be marked on the product and / or the product packaging.
In the event of a conflict between the information in this document and information provided with the product or on the website for a particular product, the product documentation takes
precedence.
CAUTION
Indicates the presence of a hazard that may cause
minor personal injury or property damage if the
CAUTION is ignored.
WARNING
Indicates the presence of a hazard that may result
in serious personal injury if the WARNING is
ignored.
Indicates potential hazard if indicated information is
ignored.
Your server should be integrated and serviced only by technically qualified persons.
You must adhere to the guidelines in this guide and the assembly instructions in your server manuals to ensure and maintain
compliance with existing product certifications and approvals.
Use only the described, regulated components specified in this
guide. Use of other products / components will void the UL Listing and other regulatory approvals of the product, and may
result in noncompliance with product regulations in the
region(s) in which the product is sold.
Indicates shock hazards that result in serious injury
or death if safety instructions are not followed.
Indicates hot components or surfaces.
Indicates do not touch fan blades, may result in
injury.
Safety Warnings and Cautions
Indicates to unplug all AC power cord(s) to disconnect AC power.
To avoid personal injury or property damage, before you begin
installing the product, read, observe, and adhere to all of the following safety instructions and information. The following safety
3-1
SAFETY INFORMATION
INTENDED APPLICATION USES
test equipment), other than an ITE application, may require further evaluation.
Please recycle battery.
Site Selection
The rail racks are designed to carry only the weight
of the server system. Do not use rail-mounted
equipment as a workspace. Do not place additional
load onto any rail-mounted equipment.
The system is designed to operate in a typical office environment. Choose a site that is:

Indicates two people are required to safely handle
the system.

Restricted Access Location: The server is
intended for installation only in a Server Room or
Computer Room where both these conditions
apply:
 access can only be gained by SERVICE PERSONS or by USERS who have been instructed
about the reasons for the restrictions applied to
the location and about any precautions that shall
be taken; and
 access is through the use of a TOOL or lock and
key, or other means of security, and is controlled
by the authority responsible for the location.





Intended Application Uses

This product was evaluated as Information Technology Equipment (ITE), which may be installed in offices, schools, computer
rooms, and similar commercial type locations. The suitability of
this product for other product categories and environments
(such as medical, industrial, residential, alarm systems, and
3-2
Clean, dry, and free of airborne particles (other than normal room dust).
Well-ventilated and away from sources of heat including
direct sunlight and radiators.
Away from sources of vibration or physical shock.
Isolated from strong electromagnetic fields produced by
electrical devices.
In regions that are susceptible to electrical storms, we recommend you plug your system into a surge suppressor
and disconnect telecommunication lines to your modem
during an electrical storm.
Provided with a properly grounded wall outlet.
Provided with sufficient space to access the power supply
cord(s), because they serve as the product's main power
disconnect.
Provided with either two independent AC power sources
or two independent phases from a s single source.
SAFETY INFORMATION
EQUIPMENT HANDLING PRACTICES
Equipment Handling Practices
Reduce the risk of personal injury or equipment damage:



To reduce the weight for easier handling, remove any easily detachable components.
!
!
WHEN REPLACING A HOT-PLUG POWER SUPPLY, UNPLUG THE POWER
CAUTION!
CORD TO THE POWER SUPPLY BEING REPLACED BEFORE REMOVING IT
FROM THE SERVER.
Power and Electrical Warnings
!
!
Conform to local occupational health and safety requirements when moving and lifting equipment.
Use mechanical assistance or other suitable assistance
when moving and lifting equipment.
CAUTION!
THE POWER SUPPLY IN THIS PRODUCT CONTAINS NO USER-SERVICEABLE PARTS. DO NOT OPEN THE POWER SUPPLY. HAZARDOUS VOLTAGE, CURRENT AND ENERGY LEVELS ARE PRESENT INSIDE THE POWER
SUPPLY. RETURN TO MANUFACTURER FOR SERVICING.
!
CAUTION!
THE POWER BUTTON, INDICATED BY THE STAND-BY POWER MARKING,
DOES NOT COMPLETELY TURN OFF THE SYSTEM AC POWER, 5V
STANDBY POWER IS ACTIVE WHENEVER THE SYSTEM IS PLUGGED IN.
TO REMOVE POWER FROM SYSTEM, YOU MUST UNPLUG THE AC
POWER CORD FROM THE WALL OUTLET. YOUR SYSTEM MAY USE MORE
THAN ONE AC POWER CORD. MAKE SURE ALL AC POWER CORDS ARE
UNPLUGGED. MAKE SURE THE AC POWER CORD(S) IS / ARE
UNPLUGGED BEFORE YOU OPEN THE CHASSIS, OR ADD OR REMOVE
ANY NON HOT-PLUG COMPONENTS.
CAUTION!
TO AVOID RISK OF ELECTRIC SHOCK, TURN OFF THE SERVER AND DISCONNECT THE POWER CORD, TELECOMMUNICATIONS SYSTEMS, NETWORKS, AND MODEMS ATTACHED TO THE SERVER BEFORE OPENING IT.
Power Cord Warnings
If an AC power cord was not provided with your product, purchase one that is approved for use in your country.
!
CAUTION!
CAUTION!
TO AVOID ELECTRICAL SHOCK OR FIRE, CHECK THE POWER CORD(S)
THAT WILL BE USED WITH THE PRODUCT AS FOLLOWS:
Do not attempt to modify or use the AC power cord(s) if they
are not the exact type required to fit into the grounded electrical
outlets.
 The power cord(s) must meet the following criteria: The power
cord must have an electrical rating that is greater than that of
the electrical current rating marked on the product.

DO NOT ATTEMPT TO MODIFY OR USE AN AC POWER CORD IF IT IS NOT
THE EXACT TYPE REQUIRED. A SEPARATE AC CORD IS REQUIRED FOR
EACH SYSTEM POWER SUPPLY.
3-3
SAFETY INFORMATION
!
!
!
SYSTEM ACCESS WARNINGS
System Access Warnings
CAUTION!
THE POWER CORD MUST HAVE SAFETY GROUND PIN OR CONTACT
THAT IS SUITABLE FOR THE ELECTRICAL OUTLET.
!
CAUTION!
CAUTION!
TO AVOID PERSONAL INJURY OR PROPERTY DAMAGE, THE FOLLOWING
SAFETY INSTRUCTIONS APPLY WHENEVER ACCESSING THE INSIDE OF
THE PRODUCT:
THE POWER SUPPLY CORD(S) IS / ARE THE MAIN DISCONNECT DEVICE
TO AC POWER. THE SOCKET OUTLET(S) MUST BE NEAR THE EQUIPMENT AND READILY ACCESSIBLE FOR DISCONNECTION.



CAUTION!

THE POWER SUPPLY CORD(S) MUST BE PLUGGED INTO SOCKET-OUTLET(S) THAT IS /ARE PROVIDED WITH A SUITABLE EARTH GROUND.




!
3-4
Turn off all peripheral devices connected to this product.
Turn off the system by pressing the power button to off.
Disconnect the AC power by unplugging all AC power cords
from the system or wall outlet.
Disconnect all cables and telecommunication lines that are
connected to the system.
Retain all screws or other fasteners when removing access
cover(s). Upon completion of accessing inside the product,
refasten access cover with original screws or fasteners.
Do not access the inside of the power supply. There are no serviceable parts in the power supply. Return to manufacturer for
servicing.
Power down the server and disconnect all power cords before
adding or replacing any non hot-plug component.
When replacing a hot-plug power supply, unplug the power
cord to the power supply being replaced before removing the
power supply from the server.
CAUTION!
IF THE SERVER HAS BEEN RUNNING, ANY INSTALLED PROCESSOR(S)
AND HEAT SINK(S) MAY BE HOT.
SAFETY INFORMATION
!
RACK MOUNT WARNINGS
accessible, and it must be labeled as controlling power to the
entire unit, not just to the server(s).
CAUTION!
UNLESS YOU ARE ADDING OR REMOVING A HOT-PLUG COMPONENT,
ALLOW THE SYSTEM TO COOL BEFORE OPENING THE COVERS. TO
To avoid risk of potential electric shock, a proper safety ground
must be implemented for the rack and each piece of equipment
installed in it.
AVOID THE POSSIBILITY OF COMING INTO CONTACT WITH HOT COMPONENT(S) DURING A HOT-PLUG INSTALLATION, BE CAREFUL WHEN
REMOVING OR INSTALLING THE HOT-PLUG COMPONENT(S).
!
Elevated Operating Ambient - If installed in a closed or multiunit rack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment
in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
CAUTION!
TO AVOID INJURY DO NOT CONTACT MOVING FAN BLADES. IF YOUR
SYSTEM IS SUPPLIED WITH A GUARD OVER THE FAN, DO NOT OPERATE
THE SYSTEM WITHOUT THE FAN GUARD IN PLACE.
Rack Mount Warnings
Reduced Air Flow - Installation of the equipment in a rack
should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
The following installation guidelines are required by UL for
maintaining safety compliance when installing your system into
a rack.
Mechanical Loading - Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
The equipment rack must be anchored to an unmovable support to prevent it from tipping when a server or piece of equipment is extended from it. The equipment rack must be installed
according to the rack manufacturer's instructions.
Extend only one piece of equipment from the rack at a time.
Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that
overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
You are responsible for installing a main power disconnect for
the entire rack unit. This main disconnect must be readily
Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Install equipment in the rack from the bottom up, with the heaviest equipment at the bottom of the rack.
3-5
SAFETY INFORMATION
ELECTROSTATIC DISCHARGE (ESD)
Particular attention should be given to supply connections other
than direct connections to the branch circuit (e.g. use of power
strips).
!
!
DO NOT ATTEMPT TO RECHARGE A BATTERY.
!
DO NOT ATTEMPT TO DISASSEMBLE, PUNCTURE, OR OTHERWISE DAMAGE A BATTERY.
Electrostatic Discharge (ESD)
!
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE, PROVIDE SOME ESD PROTECTION BY
WEARING AN ANTISTATIC WRIST STRAP ATTACHED TO CHASSIS
GROUND
-- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
CAUTION!
CAUTION!
Cooling and Airflow
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a
board from its protective wrapper or from the server, place the
board component side up on a grounded, static free surface.
Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
!
Other Hazards
CAUTION!
CAREFULLY ROUTE CABLES AS DIRECTED TO MINIMIZE AIRFLOW
BLOCKAGE AND COOLING PROBLEMS. FOR PROPER COOLING AND AIRFLOW, OPERATE THE SYSTEM ONLY WITH THE CHASSIS COVERS
INSTALLED. OPERATING THE SYSTEM WITHOUT THE COVERS IN PLACE
CAN DAMAGE SYSTEM PARTS. TO INSTALL THE COVERS:
Check first to make sure you have not left loose tools or parts
inside the system.
 Check that cables, add-in cards, and other components are
properly installed.
 Attach the covers to the chassis according to the product
instructions.

Battery Replacement
!
CAUTION!
DISPOSE OF BATTERIES ACCORDING TO LOCAL ORDINANCES AND REGULATIONS.
CAUTION!
THERE IS THE DANGER OF EXPLOSION IF THE BATTERY IS INCORRECTLY REPLACED. WHEN REPLACING THE BATTERY, USE ONLY THE
BATTERY RECOMMENDED BY THE EQUIPMENT MANUFACTURER.
3-6
SAFETY INFORMATION
OTHER HAZARDS
Laser Peripherals or Devices
!
CAUTION!
TO AVOID RISK OF RADIATION EXPOSURE AND / OR PERSONAL INJURY:
Do not open the enclosure of any laser peripheral or device
Laser peripherals or devices are not serviceable
 Return to manufacturer for servicing.
 Use certified and rated Laser Class I for Optical Transceiver
product.


3-7
Regulatory and Compliance
Information
Chapter
Chapter
REGULATORY AND COMPLIANCE INFORMATION
PRODUCT REGULATORY COMPLIANCE MARKINGS
4.1 Product Regulatory Compliance Markings
This product is marked with the following Product Certification
markings:
Table 10-1: Product Regulatory Compliance Markings (Continued)
Table 10-1: Product Regulatory Compliance Markings
REGULATORY
COMPLIANCE
cULus Listing
Marks
CE Mark
FCC Marking
(Class A)
VCCI Marking (Class A)
REGION
MARKING
BSMI Certification Number & Class A
Warning
Taiwan
GOST R
Marking
Russia
R43039
USA /
Canada
Europe
USA
This Class A digital apparatus complies with Canadian ICES-003.
This device complies with Part 15 of the
FCC Rules. Operation of this device is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
ICES Canada
Recycling
Package
Mark
Japan
4-1
Cet appareil numérique de la
classe A est conforme à la norme
NMB-003 du Canada.
Other than
China
REGULATORY AND COMPLIANCE INFORMATION
ELECTROMAGNETIC COMPATIBILITY NOTICES
4.2 Electromagnetic Compatibility Notices
FCC Verification Statement (USA)

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the
grantee of this device could void the user's authority to operate
the equipment. The customer is responsible for ensuring compliance of the modified product.
Only peripherals (computer input/output devices, terminals,
printers, etc.) that comply with FCC Class A or B limits may be
attached to this computer product. Operation with noncompliant
peripherals is likely to result in interference to radio and TV
reception.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:



Consult the dealer or an experienced radio/TV technician
for help.
All cables used to connect to peripherals must be shielded and
grounded. Operation with cables, connected to peripherals, that
are not shielded and grounded may result in interference to
radio and TV reception.
Europe (CE Declaration of
Conformity)
Reorient or relocate the receiving antenna.
This product has been tested in accordance too, and complies
with the Low Voltage Directive (73/23/EEC) and EMC Directive
(89/336/EEC). The product has been marked with the CE Mark
to illustrate its compliance.
Increase the separation between the equipment and the
receiver
Connect the equipment to an outlet on a circuit other than
the one to which the receiver is connected.
4-2
REGULATORY AND COMPLIANCE INFORMATION
VCCI (JAPAN)
VCCI (Japan)
Regulated Specified Components
To maintain the UL listing and compliance to other regulatory
certifications and/or declarations, the following regulated components must be used and conditions adhered to. Interchanging
or use of other component will void the UL listing and other
product certifications and approvals.
English translation of the notice above:
Updated product information for configurations can be found on
the site at the following URL: www.qsscit.com
This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) from Information
Technology Equipment. If this is used near a radio or television
receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction
manual.
If you do not have access to the Web address, please contact
your local representative.

BSMI (Taiwan)
The BSMI Certification Marking and EMC warning is located on
the outside rear area of the product

4-3
Add-in cards: must have a printed wiring board flammability rating of minimum UL94V-1. Add-in cards containing
external power connectors and/or lithium batteries must
be UL recognized or UL listed. Any add-in card containing
modem telecommunication circuitry must be UL listed. In
addition, the modem must have the appropriate telecommunications, safety, and EMC approvals for the region in
which it is sold.
Peripheral Storage Devices: must be UL recognized or UL
listed accessory and TUV or VDE licensed. Maximum
power rating of any one device is 19 watts. Total server
configuration is not to exceed the maximum loading conditions of the power supply.
REGULATORY AND COMPLIANCE INFORMATION
RESTRICTION OF HAZARDOUS SUBSTANCES (ROHS) COMPLIANCE
Restriction of Hazardous Substances
(RoHS) Compliance
Quanta® Computer Inc. has a system in place to restrict the
use of banned substances in accordance with the European
Directive 2002/95/EC. Compliance is based on declaration that
materials banned in the RoHS Directive are either (1) below all
applicable threshold limits or (2) an approved / pending RoHS
exemption applies.
RoHS implementation details are not fully defined and may
change.
Threshold limits and banned substances are noted below:


Quantity limit of 0.1% by mass (1000 PPM) for:

Lead

Mercury

Hexavalent Chromium

Polybrominated Biphenyls Diphenyl Ethers (PBDE)
Quantity limit of 0.01% by mass (100 PPM) for:

Cadmium
End of Life / Product Recycling
Product recycling and end-of-life take-back systems and
requirements vary by country. Contact the retailer or distributor
of this product for information about product recycling and / or
take-back.
4-4
Download PDF