8.5ft Square Olefin Offset Umbrella

8.5ft Square Olefin
Offset Umbrella
Assembly and User Manual
ITEM: 940310
#M42929
The schematics in this manual are for assembly and operation illustration
only. They may differ from the umbrella’s actual appearance.
www.atleisure.com
ATLANTA, GEORGIA
Customer Service Toll Free 1-855-880-7205
Monday through Friday from 8:00am-5:00pm
(Eastern Time)
If you have any questions, problems or need additional parts please
do not return to the place of purchase. Contact our customer
service department toll free at 1-855-880-7205 or email us at
customerservice@atleisure.com
2. Package Contents |
| Replacement Parts (cont’d) 11.
No.
Description
Qty.
Re-order No.
C
Lower Cross Leg
1pc
CSL-C48X-BRZ-T
D
Upper Cross Leg
1pc
CSL-D48X-BRZ-T
F
Holder Pole
1pc
HDP-F48X-BRZ-T
G
Bolt
4pcs
HDW-GG-T
H
Washer
4pcs
HDW-HH-T
7
Crank
1pc
CRK-748G-BRZ-T
F
HH
GG
D
C
PART
DESCRIPTION
C
Lower Cross Leg
QTY(PC)
1
D
Upper Cross Leg
1
F
Holder Pole (with control knobs)
1
N
Umbrella Frame (with canopy)
1
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
10. Replacement Parts |
| Hardware Contents 3.
PART
7
PICTURE
DESCRIPTION
QUANTITY
GG
Hex Bolt M10-1.5x20
A2-70
4pcs
(in the blister pack)
HH
Flat Washer M10 A2-70 4pcs
(in the blister pack)
UAS
F
D
H
G
PREPARATION
Before beginning assembly of product, make sure all parts are present.
Compare parts with package contents list and diagram above. If any part
is missing or damaged, contact our customer service toll free at 1-855880-7205 for replacement parts or further instructions.
C
Tools Required for Assembly: Open end wrench or adjustable wrench
(not included)
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
4. Assembly Instructions |
| Warranty 9.
Remove all protective materials. Be careful not to throw away small parts such
as screws, washers, etc. that may be wrapped in the protective materials.
HH
GG
F
HH
C
D
Fig. 1
Step 1. Place the Upper Cross Leg
(D) over Lower Cross Leg (C) to form
an “X” as shown in Fig 1.
GG
D
C
Fig. 2
Step 2. Attach the Holder Pole (F)
to the cross legs (C&D) with the
Screws(G) and Washers (H) (found in
blister pack) as shown in Fig 2. Hand
tighten only. Adjust the Holder Pole (F)
to be sure it is positioned correctly on
the base. Finally tighten all bolts. Be
careful not to over tighten.
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
90–DAY WARRANTY
This product is covered under a manufacturer’s 90-day warranty from date of
purchase against defects in materials and workmanship. This warranty does
not cover damage due to neglect, abuse or weather related damage. For full
warranty disclosure, email us at customerservice@atleisure.com.
HOW TO FILE A CLAIM
If you are within your warranty, to file a claim you must have your receipt
and pictures of your damaged umbrella. Email information to ATLeisure at
customerservice@atleisure.com.
This ATLeisure product is covered by U.S. Patent No. 5,937,882 and U.S. Patent
No. 8,104,492.
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
| Assembly Instructions (cont’d) 5.
8. Warnings |
1. Do not use this umbrella during periods of high wind and rain. Failure to
do so may result in personal injury and/or property damage.
2. Be sure to secure and/or weight the base of the umbrella.
N
N
3. Always take the umbrella down when not in use.
4. Remove the crank after set up is complete (as shown in Fig. 10) and
keep it for next time use, in order to prevent children from opening/
closing the umbrella and causing damage/injury.
5. Before opening the umbrella, please make sure that the Ballast is filled
with water. Fill the Ballast with water when necessary to increase
product stability. Recommended minimum weight of the water loaded
for proper umbrella stability is 150 lbs. Failure to do so will result in a
weight imbalance and cause the umbrella to tip over.
6. Do not stand on the umbrella base. To avoid the base from breaking or
distorting do not drag the easy ballast base on the ground.
7. Placement of the umbrella over or near a swimming pool can cause
premature fading of the canopy. This is not covered under our warranty.
8. To prevent damage to the canopy, open the umbrella facing the
opposite direction that the wind is blowing.
CANOPY CARE INSTRUCTIONS:
Simply clean the umbrella canopy with a soft brush and mild detergent.
Do not machine wash.
Do not iron.
Air dry the canopy thoroughly before storing for extended periods of time.
Make sure the canopy is completely open during drying process to prevent
shrinkage.
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
Pin
F
Control Knob
Holder Pole Ring
Fig. 3
Step 3. Insert the main pole of the
Umbrella Frame with Canopy (N) into
the Holder Pole (F) until the lower
fixed stop pin sits on the Holder Pole
Ring as shown in Fig. 3. Tighten the
two control knobs into the Holder
Pole (F) to secure the umbrella as
shown in Fig. 3.
Step 4. Use appropriate anchors
to permanently attach base to your
wooden deck or concrete patio or
use patio stones or offset umbrella
base (sold separately) to weight
down the umbrella base.
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
6. Instructions Of Set-Up & Operation |
Step 1. Unfasten the storage straps
around the canopy as shown in Fig. 4.
Storage
Straps
Fig. 4
Step 2. Open the umbrella for the
first time: Pull out the lever clamp to
release the glide handle as shown in
Fig 5. Grasp and slide the glide handle
up along the umbrella pole. Turn the
crank handle in the open direction as
shown in Fig. 5 to open the canopy
until the lower center hub reaches
the end of the support pole as shown
in Fig. 5 where the canopy has the
proper tension. Push down the lever
clamp to lock the glide handle against
the umbrella pole as shown in Fig.5
where it determines a canopy tilt
angle.
If the crank becomes too hard to crank, check
to see if the rope has come off the pulley.
If you continue to turn the crank, the rope
could break. Contact our customer service toll
free at 1-855-880-7205 for further assistance.
Step 3. If the canopy does not cover
the area on your patio as expected
(does not offer the shade to the area)
you may need to adjust the position of
the canopy to cover your desired area.
Loosen the control knobs and turn the
umbrella pole around its axis to let the
canopy move to be over your desired
area. Finally make sure to tighten the
control knobs to secure the umbrella.
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
| Instructions Of Set-Up & Operation (cont’d) 7.
Lever clamp
Glide handle
no
Ca
pen
o
py
Close
Lock
Release
Open
Fig. 5
Crank handle
A
Lever clamp
Glide handle
B
The umbrella has a unique design that
moves the pole out of your way and off
to the side. The multiple position canopy
can rotate 360°around the axis of the
main pole to offer the shade on your
expected area around the umbrella.
Contact our customer service department toll free at 1-855-880-7205 or email us at customerservice@atleisure.com
Download PDF