PHASE 7.3
OPL
USER’S MANUAL
For replacement parts, contact the distributor
from which the dryer was purchased or
Continental Girbau, Inc.®
2500 State Road 44
Oshkosh WI 54904
Telephone: (920) 231-8222 / Fax: (920) 231-4666
www.cont-girbau.com
05123JMORALES/mcronan
Part No. 113189
Retain This Manual In A Safe Place
For Future Reference
Please read this manual carefully to thoroughly familiarize yourself with the Phase 7.3 OPL computer system
features, operational instructions, and programming characteristics. This manual contains important information
on how to employ ALL the features of your new CG dryer in the safest and most economical way.
This product embodies advanced concepts in engineering, design, and safety. If this product is properly
maintained, it will provide many years of safe, efficient, and trouble free operation.
We have tried to make this manual as complete as possible and hope you will find it useful. Manufacturer
reserves the right to make changes from time to time, without notice or obligation, in prices, specifications,
colors, and material, and to change or discontinue models.
“IMPORTANT NOTE TO PURCHASER”
Information must be obtained from your local gas supplier on
the instructions to be followed if the user smells gas. These
instructions must be posted in a prominent location near the dryer.
IMPORTANT: This model 20 OPL dryer is equipped with a Phase 7.3 OPL control board used in
the free dry mode with no coin acceptor. If it becomes necessary to change any of the
dryer program parameters, the “Select Dry Mode” should remain in “Free Dry
Mode.”
Factory default settings that are relevant to this model are as follows:
PL01
Select Language
English
Select Currency
*
Select Model Type
Gas Dual Motors or Electric Dual Motors
Select Temp Scale
Fahrenheit ºF or Celsius ºC
Select Buzzer Mode
Buzz or No Buzz
Select Dry Mode
Free Dry Mode
Select Vending Safeguard
*
Select Vending Mode
*
Select Rotation Sensor
Active
PL02
High Dry Temp
160º F or 71º C
PL03
High Cool Temp
100º F or 38º C
High Cool Down Time
2 minutes
PL04
Low Dry Temp
120º F or 49º C
PL05
Low Cool Temp
100º F or 38º C
Low Cool Down Time
2 minutes
PL06
PP Dry Temp
140º F or 60º C
PL07
PP Cool Temp
100º F or 38º C
PP Cool Down Time
2 minutes
PL08
Left Coin Denomination
*
PL09
Right Coin Denomination
*
PL10
Time For Amount To Start
30 minutes
PL11
Amount To Start
*
PL12
Amount for Additional Time
*
PL13
Enter Prepurge Time
0
Enter DSI Purge Time
10-seconds
Enter DSI Proof Time
8-seconds
Enter Buzz Time
5-seconds
Enter Pause Time
1-second
PL14
PL15
Lint Cleaning Frequency
5
Retry Count
2
For factory use only
* Values have no effect in the Free Dry Mode.
Table of Contents
SECTION I
INTRODUCTION ....................................................................................................... 3
SECTION II
FEATURES.................................................................................................................. 4
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
Dependable Microprocessor Solid State Integrated Circuitry ....................................................... 4
Sensor Activated Fire Extinguishing (S.A.F.E.) System ................................................................ 4
Program Changes are Easily Made at the Keyboard (Touch Pad) ................................................ 4
Temperature Selections ............................................................................................................... 4
Cool Down ................................................................................................................................ 4
Liquid Crystal Display (L.C.D.) .................................................................................................. 4
Wrinkle Guard Program .............................................................................................................. 4
Diagnostics ................................................................................................................................. 4
Audio Alert Signal ....................................................................................................................... 4
Temperature Conversion Status ................................................................................................... 4
High-Temperature Protection ...................................................................................................... 4
RPM .......................................................................................................................................... 4
Clean Lint ................................................................................................................................... 4
Language Selection ..................................................................................................................... 5
Model Selection ......................................................................................................................... 5
Keyboard (Touch Pad) Symbols ................................................................................................. 5
Currency Selection ..................................................................................................................... 5
Dry Mode .................................................................................................................................. 5
Vending Safeguard ...................................................................................................................... 5
Credit Retention ......................................................................................................................... 5
SECTION III
OPERATING INSTRUCTIONS ............................................................................... 6
A. Coin Mode
Hot Keys-Remaining Credit, Temp, RPM ................................................................................... 6
B. Free Mode
Hot Keys-Remaining Credit, Temp, RPM ................................................................................... 6
C. Pause Mode ............................................................................................................................... 7
D. RPM .......................................................................................................................................... 7
E. Clearing Credit ........................................................................................................................... 7
F. Accessing Coin Vault .................................................................................................................. 7
SECTION IV
L.C.D. OPERATING MESSAGES........................................................................... 8
A. Coin Mode ................................................................................................................................. 8
B. Free Mode ................................................................................................................................. 8
C. Messages Common to Coin and Free Mode ............................................................................... 9
SECTION V
PROGRAM SELECTIONS (PL01-PL14) ............................................................. 10
PL01 Select Language .................................................................................................................... 10
PL01 Select Currency .................................................................................................................... 10
PL01 Select Model ........................................................................................................................ 10
PL01 Select Temp Scale ................................................................................................................. 10
PL01 Select Buzzer Mode .............................................................................................................. 10
PL01 Select Dry Mode .................................................................................................................. 11
PL01 Select Vending Safeguard ...................................................................................................... 11
PL01 Select Vending Mode ............................................................................................................ 11
PL01 Select Rotation Sensor Mode ................................................................................................ 14
PL02, PL04, PL06 High, Low, Permanent Press Cycle Dry Temp. .................................................. 14
PL03, PL05, PL07 High, Low, Permanent Press Cycle Cool Time .................................................. 15
PL08, PL09 Left/Right Coin Denomination ..................................................................................... 15
PL10 Time for Amount to Start ....................................................................................................... 15
PL11 Amount to Start ..................................................................................................................... 15
PL12 Amount for Additional Time ................................................................................................... 16
PL13 Prepurge Time ....................................................................................................................... 16
PL13 DSI Purge Time .................................................................................................................... 16
PL13 DSI Proof Time ..................................................................................................................... 16
PL13 Buzz Time ............................................................................................................................. 16
PL13 Pause Time ........................................................................................................................... 16
PL14 Lint Cleaning Frequency ........................................................................................................ 16
PL14 Retry Count .......................................................................................................................... 16
Anti-Wrinkle Program ..................................................................................................................... 17
Sensor Activated Fire Extinguishing (S.A.F.E.) System .................................................................... 17
SECTION VI
PROGRAMMING INSTRUCTIONS .................................................................... 18
A.
B.
C.
D.
Introduction to Programming ..................................................................................................... 18
Program Location Summary ...................................................................................................... 19
Programming Flowcharts .......................................................................................................... 20
Flowchart Table of Contents ..................................................................................................... 21
SECTION VII
FACTORY PRESETS .............................................................................................. 54
SECTION VIII
PHASE 7 OPL SYSTEM DIAGNOSTICS ............................................................ 55
A.
B.
C.
D.
Diagnostic (L.C.D.) Fault Messages .......................................................................................... 55
Sensor Activated Fire Extinguishing (S.A.F.E.) System Diagnostic Messages .............................. 58
Input/Output (I/O) Board Light Emitting Diode (L.E.D.) Indicators ............................................ 59
Keyboard (Touch Pad) Layout ................................................................................................. 60
SECTION I
INTRODUCTION
Phase 7.3 “OPL” Microprocessor Drying System
The Phase 7.3 Drying System has been designed with super performance in mind to provide for better temperature
regulation, efficiency, performance, consistency, and faster drying times.
Utilizing this microprocessor technology, the user simply has to place the load in the dryer, insert credit, and push
one (1) button to start the drying cycle.
The Phase 7.3 microprocessor provides a very simple user interface, while simultaneously implementing
state-of-the-art technology to ensure safety and performance. The Phase 7.3 control constantly monitors the
dryer and ALL systems to ensure proper functionality and eliminates ALL guesswork in the maintenance of the
dryer.
3
SECTION II
FEATURES
A. Dependable Microprocessor Solid State Integrated Circuitry - To eliminate as many moving parts as
possible.
B. Sensor Activated Fire Extinguishing (S.A.F.E.) System - A feature which continually monitors the
basket (tumbler) for fires. In the event of a fire, a water supply to the basket (tumbler) will suppress the fire.
The Phase 7 coin microprocessor controller (computer) will also notify the user that a fire has taken place.
C. Program Changes are Easily Made at the Keyboard (Touch Pad) - Actual programs are viewed at the
liquid crystal display (L.C.D.) for verification.
D. Temperature Selections - Accommodates three (3) temperature settings: “HI,” “PP,” and “LO,” each
programmable to a drying temperature between 100º F (38º C) and 190º F (87º C) for radial airflow or 100º
F (38º C) and 160º F (71º C) for axial airflow.
E. Cool Down - Cool down lowers the temperature in the basket (tumbler) to make the material cool enough to
handle.
F. Liquid Crystal Display (L.C.D.) - Informs user of cycle status and programs; displays important diagnostic
and fault codes.
G. Anti-Wrinkle Program - Helps keep items wrinkle-free when they are not removed from the dryer promptly
at the end of the drying and cooling cycles.
H. Diagnostics - Major circuits, including the door switch(es), microprocessor temperature sensor, heat output
circuits, and more are individually monitored, allowing for precise messages of your failure.
I. Audio Alert Signal - The tone will sound at the end of a complete drying cycle at a 1-second rate for the
duration programmed. It will also sound for any fault conditions at a quarter-second rate for four (4) beeps.
Finally there is a 3-beep warning at the beginning of every Anti-Wrinkle On Cycle, and a continuous rapid
pulse is used for the entire duration of S.A.F.E. system activation.
J. Temperature Conversion Status - Temperature related programs can be set in either Fahrenheit (ºF) or
Celsius (ºC). ALL temperatures will automatically convert to the corresponding values (+/- 1º) when changes
are made.
K. High-Temperature Protection - If the Phase 7 coin microprocessor controller (computer) senses that the
temperature in the basket (tumbler) has exceeded 180º F (82º C) for axial airflow or 210º F (98º C) for radial
airflow, it will end the drying cycle, and a fault code will be displayed indicating an overheating problem.
L. RPM - The Phase 7 coin microprocessor controller (computer) monitors the speed of the basket (tumbler)
rotation.
M. Clean Lint - This feature notifies the user when the lint access should be cleaned.
4
N. Language Selection - Phase 7 coin microprocessor controller (computer) has the ability to display six (6)
different languages: English, French, Spanish, Italian, Japanese and Dutch.
O. Model Selection - The Phase 7 coin microprocessor controller (computer) can be programmed to be used
on six (6) different model dryers, defined by heat type and the quantity of motors.
P. Keyboard (Touch Pad) Symbols -
= “PAUSE/CLEAR” key
= “PP/ENTER” key
= “HI/UP” key (scroll up)
= “LO/DOWN” key (scroll down)
Q. Currency Selection - The Phase 7 coin microprocessor controller (computer) can be programmed to
display ALL currency in one (1) of the following seven (7) currency symbols.
USD/ UK Pound/ Euro/ Belgium Franc/ French Franc/ Yen/ Lira
R. Dry Mode - The Phase 7 coin microprocessor controller (computer) can be programmed to operate in either
coin mode or free dry mode.
S. Vending Safeguard - This feature provides protection against counterfeit coins.
T. Credit Retention - In the event that the Phase 7 controller experiences a power loss, the controller will
automatically retain the amount of remaining credit that a customer had at the time of the power loss. When
power is restored, the Phase 7 controller will prompt the user to select a temp cycle, and will vend the
appropriate amount of time according to the amount of remaining credit that was present at the time of the
power loss.
5
SECTION III
OPERATING INSTRUCTIONS
A. COIN MODE
1. When the controller is in the ready state and no cycle is in progress, the liquid crystal display (L.C.D.)
screen will read “Ready, Insert $XX.XX to Start.”
2. Insert coin(s). Once the correct “Amount to Start” has been inserted, the L.C.D. will display “Select
Temperature.”
3. Select temperature by pressing “HI,” “PP,” or “LO.” The cycle will start, and the L.C.D. will display the
Dry Cycle selected and the remaining time.
4. The dryer will continue through the drying and cooling cycles until the vended time has expired.
5. Upon completion of drying and cooling cycles, the buzzer will sound and the dryer will go into Anti-Wrinkle
mode for 99 minutes or until the door has been opened.
6. HOT KEYS - When the control is in coin mode, the HOT KEYS are disabled. The HOT KEYS can be
enabled only if the dryer is in a dry cycle. The HOT KEYS cannot be enabled if the dryer is in “Ready,
Insert 25¢ to Start” mode. To enable the HOT KEYS when the controller is in a dry cycle, toggle the
program switch to the “UP” position. Once the program switch is in the “UP” position, the HOT KEYS
are enabled. The HOT KEYS are as follows:
Pressing and holding the “HI” key will show the remaining credit available.
Pressing and holding the “PP” key will show the temperature readings of the exhaust temperature transducer
and the sensor activated fire extinguishing (S.A.F.E.) system temperature probe. The exhaust temperature
reading is displayed on the left, and the S.A.F.E. system temperature reading is on the right. If the dryer is
an axial model, the temperature reading of the axial temperature transducer will also be displayed; this will
be the middle temperature reading.
Pressing and holding the “LO” key will show the RPMs of the basket (tumbler).
The “PAUSE” key will pause the dryer. If the dryer is paused, pressing the “HI,” “PP,” or “LO” key will
restart the dryer into the appropriate drying cycle. Once the dry cycle has started again, the HOT KEYS
will be enabled again.
B. FREE MODE
1. When the controller is in the ready state and no cycle is in progress, the L.C.D. screen will display “Select
Temperature.”
2. Select temperature by pressing “HI,” “PP,” or “LO.” The cycle will start and the controller will display the
Dry Cycle selected and the remaining time.
3. The dryer will continue through the drying and cooling cycles, until the drying time has expired.
6
4. Upon completion of the drying and cooling cycles, the buzzer will sound, and the dryer will go into
Anti-Wrinkle mode for 99 minutes or until the door has been opened.
5. HOT KEYS - In free mode, the HOT KEYS are always enabled. The HOT KEYS are as follows:
Pressing and holding the “HI” key will show the remaining dry time available.
Pressing and holding the “PP” key will show the temperature readings of the exhaust temperature transducer
and the sensor activated fire extinguishing (S.A.F.E.) system temperature probe. The exhaust temperature
reading is displayed on the left and the S.A.F.E. system temperature reading is on the right. If the dryer is
an axial model, the temperature reading of the axial temperature transducer will also be displayed, this will
be the middle temperature reading.
Pressing and holding the “LO” key will show the RPMs of the basket (tumbler).
The “PAUSE” key will pause the dryer. If the dryer is paused, pressing the “HI,” “PP,” or “LO” key will
restart the dryer into the appropriate drying cycle. Once the dry cycle has started again, the HOT KEYS
will be enabled again.
C. PAUSE MODE
If the “PAUSE” key is pressed and the door is not opened, the dryer will restart in 20-seconds. If the dryer door
is opened and left open, the dryer will wait for the pause time defined in PL13 to expire. Once the pause time
expires, the controller will begin to count down the dry time.
D. RPM
The Phase 7 microprocessor controller (computer) also displays the basket (tumbler) RPM by pressing and
holding the “LO” key while the basket (tumbler) is rotating (the basket [tumbler] must be rotating for
approximately 30-seconds before getting a true RPM reading). In coin mode, the program switch must be in
the “UP” position.
E. CLEARING CREDIT
Credit can be cleared from the Phase 7 controller by using the following key combination. With the program
switch down, press and hold the “PAUSE” key while entering the following key combination. “HI-HI-HI-LOLO-PP” The combination is the “HI” key three (3) times followed by the “LO” key two (2) times and then the
“PP” key one (1) time. Wait 1-second for the control to prompt the user with “Clear Credit?” If you want to
proceed, simultaneously press the “PAUSE” button and one of the remaining keys. This will clear the credit. A
flowchart of this procedure has been provided in Section VI of this manual.
F. ACCESSING COIN VAULT
The coin vault can be accessed by placing the program switch into the “UP” position. Once the program switch
is in the “UP” position, press the “HI” key. The controller will now display the amount of money in the coin
vault. Press the “HI” key again and the controller will ask to “Clear Coin Vault Total?” Press “PAUSE” for
“NO” and press “PP” for “YES.”
7
SECTION IV
L.C.D. OPERATING MESSAGES
The liquid crystal display (L.C.D.) informs the operator of cycle status and program verification and displays
important diagnostic messages and fault information.
A. COIN MODE
When the dryer is idle and is in “Ready” mode the Phase 7 coin microprocessor will display:
Ready, Insert $XX.XX to Start
XX.XX represents the amount to start defined in program memory location PL11. If the amount to start is less
than $1.00, the control will display the necessary amount to start in cents “XX¢.” If the currency setting is
changed to another currency symbol, the correct symbol will be used instead of the $ and ¢ symbols.
If dryer is equipped with a Sensor Activated Fire Extinguishing (S.A.F.E.) System and there is an issue with the
system, the control will display:
S.A.F.E. System Disabled...Ready, Insert $XX.XX to Start
The control will continue to display S.A.F.E. System disabled with ALL of the following messages until the temp
cycle is selected.
Once a coin has been inserted, the control will display:
Add XX¢ to Start or S.A.F.E. System Disabled...add XX¢ to Start
The control will continue to display this message until the appropriate amount to start has been met. Then, the
control will display:
Select Temperature or S.A.F.E. System Disabled...Select Temperature
In coin mode, if the control detects a malfunction, it will display:
Out of Order
To see the error fault, press “LO,” and the fault will be displayed. Refer to Section VIII for a complete list of
faults and descriptions.
B. FREE MODE
If control is in free mode and is in a ready state, the control will display:
Select Temperature
Likewise if the dryer is equipped with a S.A.F.E. system and there is an issue with the system, the control will
display:
S.A.F.E. System Disabled...Select Temperature
8
If a malfunction is detected in free mode, the fault will be displayed. Refer to Section VIII for complete list of
faults and descriptions.
C. MESSAGES COMMON TO COIN AND FREE MODE
Once a dry cycle has been selected, regardless of coin or free mode, the control will toggle between the
following two (2) messages:
One of the following messages depending on the cycle selected:
A.
Low Dry Temperature
High Dry Temperature
Permanent Press Temperature
And one of the following messages depending on time remaining:
B.
XX:XX minutes remaining
00:XX seconds remaining
If the dryer is paused, the control will display:
Cycle Paused...
If the door is opened, the control will display:
Main Door Open
If the main door is open, and a dry cycle is selected, the control will display:
Close Main Door
If the lint access is opened, the control will display:
Lint Access Open
If the lint access door is open, and a dry cycle is selected, the control will display:
Close Lint Access
9
SECTION V
PROGRAM SELECTIONS (PL01-PL14)
PL01-Program Location
Select Language
This location determines in what language ALL messages will be displayed. The possible selections are English,
French, Spanish, Italian, Japanese, and Dutch.
Select Currency
This location determines what currency symbol will be used on ALL currency-related messages. Possible
selections are USD, UK Pound, Euro, Belgium Franc, French Franc, Yen, and Lira.
Select Model
This location determines what type of dryer the controller will be set up as. The six (6) possible models are Gas
Single Motor, Electric Single Motor, Steam Single Motor, Gas Dual Motor, Electric Dual Motor and Steam Dual
Motor.
NOTE: In the event that the wrong model is selected, the control will go into a models fault and will
default to a Gas Single Motor dryer.
Select Temp Scale
Temperature related programs are programmable to be operated in either Fahrenheit (ºF) or Celsius (ºC). The
temperature scale selection is made in “PL01 TEMP SCALE.” Programs affected are:
1. Temperature Display Mode
2. Drying Temperatures
3. Cool Down Temperatures
IMPORTANT: When changing the temperature conversion status from Fahrenheit to Celsius or vice
versa, ALL the temperatures will be changed accordingly. The Phase 7 coin
microprocessor controller (computer) automatically calculates and converts the
temperatures in these programs to the previously set value. For example, when
changing from ºF to ºC, if the drying temperature was set for 160º F, the Phase 7 coin
microprocessor controller (computer) will change to 71º C (+/- [1] one-degree
Celsius).
Select Buzzer Mode
This location determines whether the buzzer will sound at the end of each Anti-Wrinkle cycle. This option is
toggled ON/OFF. See the Anti-Wrinkle description at the end of this section for an explanation of Anti-Wrinkle
functionality.
10
Select Dry Mode
This option determines whether the dryer operates in free mode or coin mode.
Select Vending Safeguard
The controller can be set to one (1) of the following safeguards.
Bad Coin Reset -
When this option is selected and someone tampers with the coin acceptor or inserts a
foreign object, the controller will beep three (3) times and will not accept the entry and
will display “Bad Coin Reset.” The controller will automatically reset itself for the
next entry.
Bad Coin Lockout - When this option is selected and someone tampers with the coin acceptor or inserts a
foreign object, the controller will lockout and will not accept any coins for a period of
15-seconds and will display “Bad Coin Lockout.” After 15-seconds, the controller will
reset itself for the next entry.
Select Vending Mode
Vending mode determines how the controller will vend time to a customer when a coin is inserted into the dryer.
The controller uses this parameter to determine whether the controller is in Accumulative Time or Accumulative
Coin mode. Depending on which mode the controller is in, it will use a combination of the following program
locations to determine how much time will be vended to the customer.
PL08 - Left Coin Denomination
PL09 - Right Coin Denomination
PL10 - Time for Amount to Start
PL11 - Amount to Start
PL12 - Amount for Additional Time
Accumulative Time In accumulative time mode, after the initial “Amount to Start” (PL11) has been met, each additional coin afterward
will have a specific value in time, which is determined by “Time for Amount to Start” (PL10) and “Amount to
Start” (PL11).
Single Coin Acceptor Example No. 1: If the dryer is equipped with a 25¢ coin acceptor and the “Amount to Start” (PL11) is 25¢ and
the “Time for Amount to Start” (PL10) is 30 minutes. Each coin entered into the dryer will
yield 30 minutes.
Settings: PL08 .......................... 25
PL10 .......................... 30
PL11 .......................... 25
Formula: (Left Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
(25¢/25¢)(30) = 30 minutes
11
Example No. 2: If the dryer is equipped with a 25¢ coin acceptor and the “Amount to Start” (PL11) is 50¢ and
the “Time for Amount to Start” (PL10) is 30 minutes. The insertion of the first two (2) coins
into the dryer will yield 30 minutes, each additional coin entered into the dryer will yield 15
minutes.
Settings: PL08 .......................... 25
PL10 .......................... 30
PL11 .......................... 50
Formula: (Left Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
(50¢/50¢)(30) = 30 minutes
(25¢/50¢)(30) = 15 minutes
Dual Coin AcceptorExample No. 1: If the dryer is equipped with a 10¢/25¢ dual coin acceptor and the “Amount to Start” (PL11)
is 25¢ and the “Time for Amount to Start” (PL10) is 15 minutes. After the initial “Amount to
Start” (PL11) has been met, each additional 10¢ will yield 6 minutes and each additional 25¢
will yield 15 minutes.
Settings: PL08 .......................... 10
PL09 .......................... 25
PL10 .......................... 15
PL11 .......................... 25
Formula: (Left Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
(10¢/25¢)(15) = 6 minutes
(Right Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
Right Coin- (25¢/25¢)(15) = 15 minutes
Example No. 2: If the dryer is equipped with a 10¢/25¢ dual coin acceptor and the “Amount to Start” (PL11)
is 35¢ and the “Time for Amount to Start” (PL10) is 14 minutes. After the initial “Amount to
Start” (PL11) has been met, each additional 10¢ will yield 4 minutes and each additional 25¢
will yield 10 minutes.
Settings: PL08 .......................... 10
PL09 .......................... 25
PL10 .......................... 14
PL11 .......................... 35
Formula: (Left Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
(10¢/35¢)(14) = 4 minutes
(Right Coin Denomination [PL08] / Amount to Start [PL1])
(Time for Amount to Start [PL10]) = Vended Time
(25¢/35¢)(14) = 10 minutes
12
NOTE: If the vend time cannot be divided evenly by the “Amount to Start,” the “Time for Amount to
Start” will calculate precisely the amount of time entitled to the purchaser.
Accumulative Coin In accumulative coin mode, additional time can only be achieved when the “Amount for Additional Time” (PL12)
has been inserted.
Single Coin Acceptor Example No. 1: If the dryer is equipped with a 25¢ coin acceptor and the “Amount to Start” (PL11) is 50¢,
“Amount for Additional Time” (PL12) is 50¢ and the “Time for Amount to Start” (PL10) is 24
minutes. Each additional two (2) coins entered into the dryer will yield 24 minutes, no time will
be vended if only one (1) coin is inserted.
Settings: PL08 .......................... 25
PL10 .......................... 24
PL11 .......................... 50
PL12 .......................... 50
Formula: (Amount for Additional Time [PL12] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time for Amount for Additional Time (PL12)
(50¢/50¢)(24) = 24 minutes
Example No. 2: If the dryer is equipped with a 25¢ coin acceptor and the “Amount to Start” (PL11) is 50¢,
“Amount for Additional Time” (PL12) is 25¢ and the “Time for Amount to Start” (PL10) is 24
minutes. After the “Amount to Start” (PL11) has been met, each additional coin entered into
the dryer will yield 12 minutes.
Settings: PL08 .......................... 25
PL10 .......................... 24
PL11 .......................... 50
PL12 .......................... 25
Formula: (Amount for Additional Time [PL12] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time for Amount for Additional Time (PL12)
(50¢/50¢)(24) = 24 minutes
(25¢/50¢)(24) = 12 minutes
Dual Coin Acceptor Example No. 1: If the dryer is equipped with a 10¢/25¢ dual coin acceptor and the “Amount to Start” (PL11)
is 50¢, the “Amount for Additional Time” (PL12) is 20¢ and the “Time for Amount to Start”
(PL10) is 20 minutes. After the initial “Amount to Start” (PL11) has been met, each additional
20¢ will yield 8 minutes and each additional 25¢ will yield 8 minutes with 5¢ left in escrow.
Each time a 25¢ coin is inserted the remaining 5¢ will be added to escrow, once the amount in
escrow reaches 20¢ another 8 minutes will be vended.
13
Settings: PL08 .......................... 10
PL09 .......................... 25
PL10 .......................... 20
PL11 .......................... 50
PL12 .......................... 20
Formula: (Amount for Additional Time [PL12] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time for Amount for Additional Time (PL12)
(20¢/50¢)(20) = 8 minutes
(Amount for Additional Time [PL12] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time for Amount for Additional Time (PL12)
(20/50¢)(20) = 8 minutes with 5¢ in escrow.
Example No. 2: If the dryer is equipped with a 10¢/25¢ dual coin acceptor and the “Amount to Start” (PL11)
is 50¢, the “Amount for Additional Time” (PL12) is 50¢ and the “Time for Amount to Start”
(PL10) is 20 minutes. After the initial “Amount to Start” (PL11) has been met, each additional
50¢ will yield 20 minutes.
Settings: PL08 .......................... 10
PL09 .......................... 25
PL10 .......................... 20
PL11 .......................... 50
PL12 .......................... 50
Formula: (Left Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
(50¢/50¢)(20)= 20 minutes
(Right Coin Denomination [PL08] / Amount to Start [PL11])
(Time for Amount to Start [PL10]) = Vended Time
(50¢/50¢)(20) = 20 minutes
Select Rotation Sensor Mode
This option controls whether the Phase 7 microprocessor controller (computer) should monitor the rotation
of the basket (tumbler). This program location toggles ON/OFF.
PL02 (HI), PL04 (LO), PL06 (PP)-Program Locations Cycle Dry Temp.
Enter High Dry Temp 100º F to 190º F
Each temperature cycle “HI,” “PP,” and “LO” can be programmed to a dry temperature ranging from 100º F to
190º F (38º C to 87º C) in radial mode or 100º F to 160º F (38º C to 71º C) in axial mode.
14
PL03 (HI), PL05 (LO), PL07 (PP)-Program Locations Cycle Cool Temp and Time
Enter High Cool Temp 70º F to 100º F
Each temperature cycle “HI,” “PP,” and “LO” has a cool down temperature ranging from 70º F to 100º F
(21º C to 38º C). Once the dryer enters the cool down mode, the dryer will operate without heat until the
temperature in the basket (tumbler) has reached this set temperature or until the cool down time has expired,
whichever comes first.
Enter Cool Time 0 to 9 minutes
Cool down time ranges from 0 to 9 minutes. The cool down time occurs at the end of a dry cycle. If your cool
down time is set to 4 minutes, the last 4 minutes of the dry cycle will be in cool down mode.
PL08 (Left), PL09 (Right)-Program Locations Left/Right Coin Denomination
Enter Left/Right Coin Denomination 0.05 to 25.00
The left and right coin acceptors can be independently set to a value within the range of 0.05 to 25.00, adjustable
in 0.01 increments.
PL10-Program Location
Enter Time for Amount to Start 1 to 99 minutes
This location determines the time that is vended once the amount to start is met. This is programmable from 1
minute to 99 minutes in 1 minute increments.
PL11-Program Location
Amount to Start
This location determines the amount needed to start a dry cycle. The amount to start is programmable from a
minimum of 0.05 to a maximum of 25.00, adjustable in 0.01 increments.
15
PL12-Program Location
Enter Amount for Additional Time
This location determines the amount needed to add more time to a dry cycle. The amount for additional time is
programmable from a minimum of 0.05 to a maximum of 25.00 adjustable in 0.01 increments.
PL13-Program Location
Enter Prepurge Time 0- to 25-seconds
When the Phase 7 controller detects the need for heat, it will wait for this prepurge time to expire before actually
sending the signal for the heat to turn on.
Enter DSI Purge Time 0- to 25-seconds
After the controller sends the heat signal, the controller will wait for the direct spark ignition (DSI) purge time to
expire before it checks to see if the gas valve return signal is present.
Enter DSI Proof Time 0- to 20-seconds
After the controller receives a gas valve signal within the DSI purge time, the controller will begin a DSI proof
timer. After the DSI proof time has expired, the controller will recheck for the gas signal.
Enter Buzz Time 1 to 9 beeps
If the buzzer mode is set to “ON,” this location determines how many times the buzzer will beep at the end of an
Anti-Wrinkle cycle.
Enter Pause Time 0 to 3 minutes
If the pause button is pressed and the main door is open, the controller will wait for the pause time defined in this
setting to expire. Once the time has expired, the controller will begin to count down the dry time. If the pause
button is not pressed prior to opening the door, the controller will not wait for the pause time before counting
down the dry time.
PL14-Program Location
Enter Lint Cleaning Frequency 0 to 10 hours
This feature monitors the hours of drying time and compares it with the Lint Cleaning Frequency setting in PL14.
Once the lint cleaning frequency time has been met, the controller will begin prompting the user to clean the lint
drawer. The controller will allow two (2) more hours of drying time before locking out the controller. The
controller will not respond until after the lint drawer has been cleaned out. When the lint drawer is opened, the
display will read “LINT ACCESS OPEN,” and when the lint drawer is closed, the controller will go back to a
ready state and will read “Ready, Insert 25¢ to Start” (NOTE: The lint access must be opened for 5-seconds or
more for the reset to occur).
Enter Retry Count 0 to 2
This count is used to determine how many ignition attempts are allowed if an ignition attempt is unsuccessful.
This counter increments when the heat output engages and the valve signal is lost after the trial for ignition period
expires. This counter also will automatically reset once an ignition attempt is successful. The retry count range
is from 0 to 2.
16
Anti-Wrinkle
This program keeps items wrinkle-free when they are not removed from the dryer promptly at the end of the
drying cycle and/or cooling cycle.
When the drying and cooling cycle is completed, the dryer will shut off, the tone will sound, and the liquid crystal
display (L.C.D.) will read “ANTI-WRINKLE.” If the door is not opened, the Phase 7 coin microprocessor
controller (computer) will wait until the Anti-Wrinkle Delay Time of 2 minutes has expired, at which time the fan
will start and the basket (tumbler) will rotate (without heat) for the Anti-Wrinkle On Time of 2 minutes. The
Phase 7 coin microprocessor controller (computer) will repeat this process until the Maximum Anti-Wrinkle
Time of 99 minutes has expired or until the door is opened, whichever comes first. Prior to each ON time, there
is a 3-beep warning that the fan and basket (tumbler) rotation is about to start. The beeps at the end of the
Anti-Wrinkle Cycle can be programmed to be ON/OFF, refer to page 10 for PL01 - Select Buzzer Mode.
NOTE: The following information description is an explanation of the sensor activated fire extinguishing
(S.A.F.E.) system functionality. This feature is programmed at the factory and effects dryers
that are equipped with the S.A.F.E. system.
Sensor Activated Fire Extinguishing (S.A.F.E.) System
While the dryer is in an idle state or 20-seconds after the heat turns off, the Phase 7 control monitors the
S.A.F.E. system probe located in the top of the basket (tumbler) chamber and records the minimum temperature.
If the minimum recorded S.A.F.E. system probe temperature is no less than 120° F (48° C) and the control
detects a 50° rise in temperature, this will be the trip point and the S.A.F.E. system routine will activate.
While a drying cycle is in process and the heat has turned on at least once, the Phase 7 control monitors the
exhaust temperature transducer. If the drying cycle temperature set point is set greater than 160° F (71° C) and
the control detects an exhaust temperature rise 25° F greater than set point, this will be the trip point and the
S.A.F.E. system routine will activate. If set point is below 160° F (71° C) the trip point will be 185° F (85° C).
Once the S.A.F.E. system routine is activated, water will be injected into the basket (tumbler) chamber. Any
time water is being injected into the basket (tumbler); the basket (tumbler) drive will turn the load for 1-second
every 15-seconds. This process will continue for a minimum of 2 minutes. After 2 minutes has elapsed, the
control will check if the temperature remained above trip point, if so water will remain on. The control will
continue to check if temperature is above trip point every 30-seconds. If the water has been on for a constant
10 minutes, the water will be turned off regardless of the temperature. If the temperature has dropped below
trip point, the control will turn off the water prior to 10 minutes.
17
SECTION VI
PROGRAMMING INSTRUCTIONS
A. INTRODUCTION TO PROGRAMMING
The various program selections are stored in the Phase 7 coin microprocessor controller (computer) and are
broken down into fifteen (15) program locations. PL01 through PL14 are for dryer parameters and PL15 is
reserved for factory settings.
ALL program changes are done through the keyboard (touch pad) selection keys on the front of the control
panel.
ENTERING THE PROGRAMMING MODE:
First, make sure that no cycle is in progress and that the liquid crystal display (L.C.D.) reads “Ready, Insert 25¢
to Start,” then place the program switch in the “UP ” position. This will put you into the programming mode.
EXITING THE PROGRAMMING MODE:
To exit the program mode, place the program switch in the “DOWN” position.
To alter the programming parameters, the operator will locate the parameter (program) that is to be changed. If
the change is a numerical change (i.e., time and/or temperature), the operator will use the “HI” and “LO” keys
to scroll through the numerical range of numbers, using “HI” to increase and “LO” to decrease. If an error is
made, press the “PAUSE”
key ONCE, and the incorrect entry that was made will be cancelled. Once the
entry is made and the parameter (program) set does not need to be changed, press the “PP”
key, and the
Phase 7 coin microprocessor controller (computer) will save the change and will advance to the next parameter.
If the parameter (program) change is a feature change, such as changing the temperature conversion from
degree Fahrenheit (ºF) to degree Celsius (ºC), the operator will press the “HI” or “LO” key. This will toggle
between choices. Once the entry is made, or if the parameter (program) does not need to be changed, press the
“PP”
key and the Phase 7 coin microprocessor controller (computer) will save the change and will advance
to the next program selection.
The Phase 7 coin microprocessor controller (computer) allows the operator to scroll through the various
programming locations and select the parameter to be changed. If no other programs (parameters) need to be
changed, the user can get out of the program mode by toggling the program switch to the “DOWN” position.
The Phase 7 coin microprocessor controller (computer) will be returned to the operating mode, and the L.C.D.
will read “Ready, Insert 25¢ to Start” in coin mode or “Select Temperature” in free mode.
18
B. PROGRAM LOCATION SUMMARY
Phase 7 Coin Program Location Summary
PL01
Select Language
Select Currency
Select Model
Select Temp Scale
Select Buzzer Mode
Select Dry Mode
Select Vending Safe Guard
Select Vending Mode
Select Rotation Sensor Mode
PL02
High Dry Temperature
PL03
High Cool Temperature
High Cool Time
PL04
Low Dry Temperature
PL05
Low Cool Temperature
Low Cool Time
PL06
Permanent Press Temperature
PL07
Permanent Press Cool Temperature
Permanent Press Cool Time
PL08
Left Coin Denomination
PL09
Right Coin Denomination
PL10
Time For Amount to Start
PL11
Amount to Start
PL12
Amount For Additional Time
PL13
Enter Pre-Purge Time
Enter DSI Purge Time
Enter DSI Proof Time
Buzz Time
Pause Time
PL14
Lint Cleaning Frequency
Retry Count
PL15
Hidden Locations
P/N: 114548
19
C. PROGRAMMING FLOWCHARTS
The following section of this manual explains the programming of the Phase 7 coin microprocessor controller
(computer) program locations (system parameters) through the use of flowcharts. A flowchart is nothing more
than a diagram of the programming process.
Five (5) different symbols will be used in these flowcharts:
display symbol
Ready
HI
LO
PP
PAUSE
Each display symbol will represent a readout on the Phase 7 coin microprocessor controller (computer) liquid
crystal display (L.C.D.), and each key symbol will represent a key that is pressed. For example:
1. If the flowchart shows the symbol
display will read the same.
Ready
the Phase 7 coin microprocessor controller (computer) L.C.D.
2. If the flowchart shows a key symbol, you will press that specific key on the keyboard (touch pad) label.
3. a. The flowchart arrows (i.e.,
) represent the program path.
b. On the sides of these flowcharts are explanations of the flowchart procedure, and in some cases the
programming limits or options.
Listed on the next page is an index of the flowcharts to follow.
20
Flowchart Table of Contents
Programming Location
PL01
PL01
PL01
PL01
PL01
PL01
PL01
PL01
PL01
PL02
PL03
PL03
PL04
PL05
PL05
PL06
PL07
PL07
PL08
PL09
PL10
PL11
PL12
PL13
PL13
PL13
PL13
PL13
PL14
PL14
Title
Page
Selecting Display Language ..........................
Selecting Currency .......................................
Selecting Model Type ..................................
Selecting Temp Scale ...................................
Selecting Buzzer Mode ................................
Selecting Dry Mode .....................................
Selecting Vending Safeguard .........................
Selecting Vending Mode ...............................
Selecting Rotation Sensor Mode ..................
Setting High Cycle Dry Temp .......................
Setting High Cycle Cool Temp .....................
Setting High Cycle Cool Time .......................
Setting Low Cycle Dry Temp .......................
Setting Low Cycle Cool Temp .....................
Setting Low Cycle Cool Time .......................
Setting Permanent Press Cycle Dry Temp .....
Setting Permanent Press Cycle Cool Temp ...
Setting Permanent Press Cycle Cool Time ....
Setting Left Coin Denomination ....................
Setting Right Coin Denomination ..................
Setting Time for Amount to Start ...................
Setting Amount to Start ................................
Setting Amount for Additional Time ...............
Setting Prepurge Time ..................................
Setting DSI Purge Time ................................
Setting DSI Proof Time ................................
Setting Buzz Time .........................................
Setting Pause Time .......................................
Setting Lint Cleaning Frequency ...................
Setting Retry Count ......................................
Clearing Credit ............................................
Accessing and Clearing Coin Vault Total .......
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Selecting Display Language
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to "UP"
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "PP" to enter
Language Parameter
English
Press "HI" or "LO" to scan through
different languages: English, French,
Italian,Spanish, Dutch, Japanese.
Spanish
Press "PP" to select new
Language and advance to
next parameter
Seleccione tipo de
dinero
Note: Press "PAUSE" to exit
PL #01 memory location
22
Selecting Currency
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" one (1) time to
scan up to Currency
Parameter
Select Currency
Press "PP" to enter
Currency Parameter
USD
Press "HI" or "LO" to scan
through different currency:
USD,UK Pound, Euro,
Belgium Franc, French Franc,
Yen, Lira.
Euro
Press "PP" to select new
Currency, and advance to
next parameter.
Note: Press "PAUSE" to exit
PL #01 memory location
Select Model
23
Selecting Model Type
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" two (2) times to
scan up to Model
Parameter
Select Model
Press "PP" to enter Dryer
Model Parameter.
Gas Single Motor
Press "HI" or "LO" to scan
through different dryer models:
Gas Single Motor, Electirc
Single Motor, Steam Single
Motor, Gas Dual Motor,
Electric Dual Motor, Steam
Dual Motor.
Electric Single
Motor
Press "PP" to select new
model, and advance to
next parameter.
Note: Press "PAUSE" to exit
PL #01 memory location
Select Temp Scale
24
Selecting Temp Scale
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" three (3) times
to scan up to Select Scale
Temp Parameter
Select Temp Scale
Press "PP" to enter Temp
Scale Parameter.
Degrees F
Press "HI" or "LO" to toggle
between Fahrenheit and
Celsius
Celsius
Press "PP" to select new
Temp Scale, and advance
to next parameter.
Select Buzzer
Mode
Note: Press "PAUSE" to exit
PL #01 memory location
25
Selecting Buzzer Mode
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" four (4) times to
scan up to Buzzer Mode
Parameter
Select Buzzer
Mode
Press "PP" to enter Buzzer
Mode Parameter
Buzz
Press "HI" or "LO" to
toggle between Buzz and
No Buzz
No Buzz
Press "PP" to select
Buzzer Mode, and
advance to next
parameter.
Note: Press "PAUSE" to exit
PL #01 memory location
Select Dry Mode
26
Selecting Dry Mode
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" five (5) times to
scan up to Dry Mode
Parameter
Select Dry Mode
Press "PP" to enter Dry
Mode Parameter
Free Mode
Press "HI" or "LO" to toggle
between Coin and Free
Mode
Coin Mode
Press "PP" to select Dry
Mode and advance to
next parameter
Select Vending
Safe Guard
Note: Press "PAUSE" to exit
PL #01 memory location
27
Selecting Vending Safe Guard
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" six (6) times to
scan up to Vending Safe
Guard Parameter
Select Vending
Safe Guard
Press "PP" to enter
Vending Safe Guard
parameter.
Bad Coin Reset
Press "HI" or "LO" to toggle
between Bad Coin Reset
and Bad Coin Lockout
Bad Coin Lock Out
Press "PP" to select
Vending Safe Guard and
advance to next
parameter.
Select Vending
Mode
Note: Press "PAUSE" to exit
PL #01 memory location
28
Selecting Vending Mode
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select
Language
Press "HI" seven times to
scan up to Vending Mode
Parameter
Select Vending
Mode
Press "PP" to enter
Vending mode Parameter.
Accumulative
Time
Press "HI" or "LO" to toggle
between Accumulative Time and
Accumulative Coin
Accumulative
coin
Press "PP" to select
vending mode and
advance to next
parameter.
Select Rotation
Sensor Mode
Note: Press "PAUSE" to exit
PL #01 memory location
29
Selecting Rotation Sensor Mode
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "PP" to enter
PL #01
Select Language
Press "HI" eight (8) times
to scan up to Rotation
Sensor Parameter
Select Rotation
Sensor Mode
Press "PP" to enter
Rotation Sensor Mode
Parameter
Rotation Sensor
Active
Press "HI" or "LO" to
toggle between Rotation
Sensor Active and No
Rotation Sensor
No Rotation
Sensor
Press "PP" to select
Rotation Sensor Mode
and advance to next
parameter.
Note: Press "PAUSE" to exit
PL #01 memory location
PL #02
30
Setting High Cycle Dry Temp
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" one (1) time to
scan up to PL #02
PL #02
Press "PP" to enter
PL #02
Enter High Dry Temp
100 to 190 ° F
Press "PP" to proceed
160
Press "HI" to increase
High Dry Temp or "LO" to
decrease High Dry Temp
180
Press "PP" to select
High Dry Temp and
advance to next
parameter.
Note: Press "PAUSE" to exit
PL #02 memory location
PL #03
31
Setting High Cycle Cool Temp
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" two (2) times to
scan up to PL #03
PL #03
Press "PP" to enter
PL #03
Enter High Cool
Temp 70 to 100 ° F
Press "PP" to proceed
100
Press "HI" to increase
High Cool Temp or "LO" to
decrease High Cool Temp
80
Press "PP" to enter High
Cool Temp and advance
to next parameter
Enter High Cool
Time 0 to 9
minutes
Note: Press "PAUSE" to exit
PL #03 memory location
32
Setting High Cycle
Cool Time
Ready, Insert
0.25 ¢ to Start
Program Mode
From Ready mode toggle
Program Switch to UP
position.
Press "PP" to enter
Program Menu
PL #01
Press "HI" two (2) times to
scan up to PL #03
PL #03
Press "PP" to enter PL #03
Enter High Cool
Temp 70 to 100 ° F
Press "HI" one (1) time to
scan up to High Cool Time
Enter High Cool
Time 0 to 9
minutes
Press "PP" to proceed
2
Press "HI" to increase
High Cool Time or "LO" to
decrease High Cool Time
3
Press "PP" to select High
Cool Time and advance to
next parameter.
PL #04
33
Note: Press "PAUSE" to exit
PL #03 memory location
Setting Low Cycle Dry Temp
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" three (3) times
to scan up to PL #04
PL #04
Press "PP" to enter
PL #04
Enter Low Dry
Temp 100 to 190 °
F
Press "PP" to proceed
160
Press "HI" to increase Low
Dry Temp or "LO" to
decrease Low Dry Temp
180
Press "PP" to select Low
Dry Temp and advance to
next parameter.
Note: Press "PAUSE" to exit
PL #04 memory location
PL #05
34
Setting Low Cycle Cool Temp
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" four (4) times
to scan up to PL #05
PL #05
Press "PP" to enter
PL #05
Enter Low Cool
Temp 70 to 100 ° F
Press "PP" to proceed
100
Press "HI" to increase Low
Cool Temp or "LO" to
decrease Low Cool Temp
80
Press "PP" to select Low
Cool Temp and advance
to next parameter.
Enter Low Cool
Time 0 to 9
minutes
Note: Press "PAUSE" to exit
PL #05 memory location
35
Setting Low Cycle
Cool Time
Ready, Insert
0.25 ¢ to Start
Program Mode
From Ready mode toggle
Program Switch to UP
position.
Press "PP" to enter
Program Menu
PL #01
Press "Hi" four (4) times
to scan up to PL #05
PL #05
Press "PP" to enter
PL #05
Enter Low Cool
Temp 70 to 100 ° F
Press "HI" to one (1) time
to scan up to Low Cool
Time
Enter Low Cool
Time 0 to 9
minutes
Press "PP" to proceed
2
Press "HI" to increase
Low Cool Time or "LO" to
decrease Low Cool Time
5
Press "PP" to select Cool
Time and advance to next
parameter.
PL #06
36
Note: Press "PAUSE" to exit
PL #05 memory location
Setting Permanent Press Cycle Dry Temp
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" five (5) times to
scan up to PL #06
PL #06
Press "PP" to enter
PL #06
Enter Permanent
Press Dry Temp
100 to 190 ° F
Press "PP" to proceed
160
Press "HI" to increase
Permanent Press Dry
Temp or "LO" to decrease
Permanent Press Dry
Temp
160
Press "PP" to select
Permanent Press Dry
Temp and advance to
next parameter.
Note: Press "PAUSE" to exit
PL #06 memory location
PL #07
37
Setting Permanent
Press Cycle Cool Temp
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" six (6) times to
scan up to PL #07
PL #07
Press "PP" to enter
PL #07
Enter Permanent
Press Cool Temp
70 to 100 ° F
Press "PP" to proceed
100
Press "HI" to increase
Permanent Press Cool
Temp or "LO" to decrease
Permanent Press Cool
Temp
90
Press "PP" to select
Permanent Press Cool
Temp and advance to
next parameter.
Enter Permanent
Press Cool Time 0
to 9 minutes
38
Note: Press "PAUSE" to exit
PL #07 memory location
Setting Permanent
Press Cycle Cool
Time
Ready, Insert
0.25 ¢ to Start
From Ready mode
toggle Program Switch
to UP position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" six (6) times to
scan up to PL# 07
PL #07
Press "PP" to enter
PL #07
Enter Permanent
Press Cool Temp
70 to 100 ° F
Press "HI" to scan up to
Permanent Press Cool
Time
Enter Permanent
Press Cool Time 0
to 9 minutes
Press "PP" to proceed
2
Press "HI" to increase
Permanent Press Cool
Time or "LO" to decrease
Permanent Press Cool
Time
5
Press "PP" to select
Permanent Press Cool
Time and advance to next
parameter.
PL #08
39
Note: Press "PAUSE" to exit
PL #07 memory location
Setting Left Coin Denomination
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" seven (7) times
to scan up to PL #08
PL #08
Press "PP" to enter
PL #08
Enter Left Coin
Denomination 0.05
to 25.00
Press "PP" to proceed
0.25
Press "HI" to increase Left
Coin Denomination and
"LO" to decrease Left Coin
Denomination
0.10
Press "PP" to select Left
Coin Denomination and to
proceed to next parameter
PL #09
Note: Press "PAUSE" to exit
PL #08 memory location
40
Setting Right Coin Denomination
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" eight (8) times
to scan up to PL #09
PL #09
Press "PP" to enter
PL #09
Enter Right Coin
Denomination
0.05 to 25.00
Press "PP" to proceed
.25
Press "HI" to increase
Right Coin Denomination
and "LO" to decrease
Right Coin Denomination
.50
Press "PP" to select Right
Coin Denomination and
advance to next parameter
PL #10
Note: Press "PAUSE" to exit
PL #09 memory location
41
Setting Time for Amount to Start
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" nine (9) times to
scan up to PL #10
PL #10
Press "PP" to enter
PL #10
Enter Time for
Amount to Start
1 to 99 minutes
Press "PP" to proceed
10
Press "HI" to increase or
"LO" to decrease Time for
Amount to Start
12
Press "PP" to select Time
for Amount to Start and
advance to next
parameter.
Note: Press "PAUSE" To exit
PL #10 memory location
PL #11
42
Setting Amount To Start
Ready, Insert
0.25 ¢ to Start
From Ready mode
toggle Program Switch
to UP position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" ten (10) times
to scan up to PL #11
PL #11
Press "PP" to enter
PL #11
Enter Amount to
Start 0.05 to 25.00
Press "PP" to proceed
.25
Press "HI" to increase or
"LO" to decrease Amount
to Start
.20
Press "PP" to select
Amount to Start
Note: Press "PAUSE" To exit
PL #11 memory location
PL #12
43
Setting Amount for Additional Time
Ready, Insert
0.25 ¢ to Start
From Ready mode
toggle Program Switch
to UP position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" eleven (11)
times to scan up to PL
#12
PL #12
Press "PP" to enter
PL #12
Enter Amount for
Additional Time
0.05 to 25.00
Press "PP" to proceed
.25
Press "HI" to increase or
"LO" to decrease Amount
for Addtitional Time
.50
Press "PP" to select
Amount for Additional
Time and to advance to
next parameter
Note: Press "PAUSE" To exit
PL #12 memory location
PL #13
44
Setting Pre Purge
Time
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" twelve (12)
times to scan up to PL #13
PL #13
Press "PP" to enter
PL #13
Enter Pre Purge
Time 0 to 25
seconds
Press "PP" to proceed
2
Press "HI" to increase or
"LO" to decrease PrePurge time
5
Press "PP" to select Pre
Purge time and to advance
to next parameter.
Enter DSI Purge
Time 0 to 25
seconds
45
Note: Press "PAUSE" To
exit PL #13 memory location
Setting DSI
Purge Time
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" twelve (12)
times to scan up to PL #13
PL #13
Press "PP" to enter
PL #13
Enter Pre Purge
Time 0 to 25
seconds
Press "HI" one (1) time to
scan up to DSI Purge
Time.
Enter DSI Purge
Time 0 to 25
seconds
Press "PP" to proceed
2
Press "HI" to increase or
"LO" to decrease DSI
Purge Time
5
Press "PP" to select DSI
Purge Time and to
advance to next
parameter.
Enter DSI Proof
Time 0 to 25
seconds
46
Note: Press "PAUSE" To exit
PL #13 memory location
Setting DSI Proof
Time
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" twelve (12)
times to scan up to PL
#13
PL #13
Press "PP" to enter
PL #13
Enter Pre Purge
Time 0 to 25
seconds
Press "HI" two (2) times to
scan up to DSI Proof Time
Enter DSI Proof
Time 0 to 20
seconds
Press "PP" to proceed
2
Press "HI" to increase or
"LO" to decrease DSI
Proof Time
5
Press "PP" to select DSI
Proof Time and to
advance to next parameter
Enter Buzz Time 0
to 9 Beeps
47
Note: Press "PAUSE" To exit
PL #13 memory location
Setting Buzz Time
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" twelve (12)
times to scan up to PL
#13
PL #13
Press "PP" to enter
PL #13
Enter Pre
PurgeTime
0 to 25 seconds
Press "HI" three (3) times
to scan up to Buzz Time
Enter Buzz Time
0 to 9 Beeps
Press "PP" to proceed
2
Press "HI" to increase or
"LO" to decrease Buzz
Time
5
Press "PP" to select Buzz
Time and to advance to
next parameter.
Enter Pause Time
0 to 3 minutes
48
Note: Press "PAUSE" To exit
PL #13 memory location
Setting Pause Time
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" twelve (12)
times to scan up to
PL #13
PL #13
Press "PP" to enter
PL #13
Enter Pre Purge
Time 0 to 25
seconds
Press "HI" four (4) times to
scan up to Pause Time
Enter Pause Time
0 to 3 minutes
Press "PP" to proceed
2
Press "HI" to increase or
"LO" to decrease Pause
Time
5
Press "PP" to select Pause
Time and to advance to
next parameter.
PL #14
49
Note: Press "PAUSE" To exit
PL #13 memory location
Setting Lint Cleaning Frequency
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" thirteen (13)
times to scan up to
PL #14
PL #14
Press "PP" to enter
PL #14
Enter Lint Cleaning
Frequency 0 to 10
Press "PP" to proceed
2
Press "HI" to increase or
"LO" to decrease Lint
Cleaning Frequency
5
Press "PP" to select Lint
Cleaning Frequency and
to advance to next
parameter.
Enter Retry Count
0 to 2
Note: Press "PAUSE" To exit
PL #14 memory location
50
Setting Retry Count
Ready, Insert
0.25 ¢ to Start
From Ready mode toggle
Program Switch to UP
position.
Program Mode
Press "PP" to enter
Program Menu
PL #01
Press "HI" thirteen (13)
times to scan up to
PL #14
PL #14
Press "PP" to enter
PL #14
Enter Lint Cleaning
Frequency 0 to 10
Hours
Press "HI" one (1) time to
scan up to Enter Retry
Count
Enter Retry Count
0 to 2
Press "PP" to proceed
2
Press "Hi" to increase or
"LO" to decrease Retry
Count
1
Press "PP" to select
Retry Count and to
advance to next
parameter.
PL #15
51
Note: Press "PAUSE" To exit
PL #14 memory location
Flow Chart for Clearing
Credit
- Stop Dry Cycle by Opening
and Closing Door.
Do Not use the Pause Key.
Select
Temperature to
Restart
- Make Sure Program Switch
is Down.
- Enter the Following Key
Sequence
Press and
Hold
While holding PAUSE at ALL
TIMES, press HI 3 times,
LO 2 times, and PP once.
- Wait for Display to Say
CLEAR CREDIT?
-
Clear Credit?
Ready, Insert
$0.25 to Start
52
Hold PAUSE and press PP.
Accessing and Clearing Coin Vault
Total
Ready, Insert
0.25 ¢ to Start
Enter Program Mode by
Setting the program switch
to UP position from a
Ready Mode
Program Mode
Press HI one (1)
time and
controller will
display the Coin
Vault Total.
Coin Vault total is
$XXX
Press HI one (1)
more time and
control will
prompt to clear
Coin Vault Total
Clear Coin Vault
Total?
YES
NO
Press PP for YES
or press PAUSE
for NO
Program Mode
53
SECTION VII
FACTORY PRESETS
Factory Defaults
PL01
PL02
PL03
PL04
PL05
PL06
PL07
PL08
PL09
PL10
PL11
PL12
PL13
PL14
Select Language
Select Currency
Select Model
Select Temp Scale
Select Buzzer Mode
Select Dry Mode
Select Vending Safeguard
Select Vending Mode
Select Rotation Sensor
High Dry Temp
High Cool Temp
High Cool Down Time
Low Dry Temp
Low Cool Temp
Low Cool Down Time
PP Dry Temp
PP Cool Temp
PP Cool Down Time
Left Coin Denomination
Right Coin Denomination
Time for Amount to Start
Amount to Start
Amount for Additional Time
Enter Pre –Purge Time
Enter DSI Purge Time
Enter DSI Proof Time
Enter Buzz Time
Enter Pause Time
Lint Cleaning Frequency
Retry Count
54
English
USD
Gas Single Motor
Fahrenheit
Buzz
Coin
Bad Coin Reset
Acc. Time
Active
180
100
2 min
120
100
2 min
150
100
2 min
.25
.10
10 min
.25
.25
0
3
8
5
1
5
2
SECTION VIII
PHASE 7 COIN SYSTEM DIAGNOSTICS
IMPORTANT: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY
AND THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY
COVERS OR GUARDS ARE REMOVED FROM THE MACHINE TO
ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, OR
TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health
Administration) STANDARDS.
ALL major circuits, including door, microprocessor temperature sensor, heat and motor circuits are monitored.
The Phase 7 coin microprocessor controller (computer) will inform the user, via the liquid crystal display (L.C.D.)
of certain failure messages, along with light emitting diode (L.E.D.) indicators on the Inputs/Outputs (I/O) on the
control board.
ERROR MESSAGES:
NOTE: Any error associated with the “Out of Order” message can be identified by pressing the “LO”
key while in the “Out of Order” condition. If the “HI” key is pressed during this time, the
remaining credit can be viewed. Any “Out of Order” message is immediately followed by a
3-second tone. If the fault has been corrected, holding the “PAUSE” key for 3-seconds will
clear the fault message. If more than one (1) fault occurred at the same time, after the first fault
is cleared, the next fault will be displayed and will need to be cleared. This will occur until
ALL faults have been displayed. In free mode, the control will not display “Out of Order;” it
will just display the fault.
A. DIAGNOSTIC (L.C.D.) FAULT MESSAGES
MODEL FAULT - This routine monitors the inputs, such as the sail switch and gas valve. Steam dryers DO
NOT use a sail switch or valve input, and an electric dryer will not use a valve input. These signals allow the
controller to interpret what type of dryer it is controlling. The controller determines what the expected dryer
responses should be for that specific heat type dryer.
NOTE: If a model error occurs, the microprocessor will always default to the “gas” type for safety
reasons. Also, the dryer is stopped and forced into a restart condition to reevaluate ALL the
expected responses.
SAIL SWITCH CLOSED FAULT - This routine prevents the start-up of the dryer unless the sail switch is in
the open position. If the sail switch is in the closed position prior to starting, the controller will display “Out of
Order” for a “Sail Switch Closed Fault,” and the dryer will not be allowed to start. This routine is also monitored
at every start-up, including during the cycle. Any time the fault occurs, there will be an audio indication and start/
restart will be prevented.
55
SAIL SWITCH OPEN FAULT - If the sail switch does not close within 8-seconds of starting or restarting a
cycle, the controller will display “Sail Switch Open Fault” condition. Or if the sail switch opens during a cycle,
the controller will immediately shut off the heat output and will monitor how long the sail switch is open for, if the
sail switch is open for more than 30-seconds the controller will display “Sail Switch Open Fault” condition. If the
basket (tumbler) temperature is above 100° F (38° C), the controller will continue to display “Open Sail Switch
Fault” while the dryer cools by running with no heat for 2 minutes or until the temperature drops below 100° F
(38° C). Once the basket (tumbler) temperature is below 100° F (38° C), the controller will shut off ALL
outputs and will go into a fault mode with a brief audio indication
BURNER HIGH LIMIT FAULT - This routine monitors the burner high limit switch. If the switch opens
during the cycle while the heat is on, the dryer will display “Burner High Limit Fault.” The controller will check
the basket (tumbler) temperature. If the exhaust probe temperature is above 100° F (38º C), the dryer will
continue to display “Burner High Limit Fault” while the dryer cools by running with no heat for 2 minutes or until
the temperature drops below 100° F (38° C). If the exhaust probe temperature is below 100° F (38º C), the
controller will shut off ALL outputs and will go into a fault mode with a brief audio indication.
EXHAUST HIGH LIMIT FAULT - This routine monitors the basket (tumbler) safety over temperature
switch. If the switch opens, the dryer will display “Exhaust High Limit Fault.” If the basket (tumbler) temperature
is above 100° F (38° C), the dryer will continue to display “Exhaust High Limit Fault” while the controller cools
by running with no heat for 2 minutes or until the temperature drops below 100° F (38º C). If the basket
(tumbler) temperature is below 100° F (38º C), the controller will shut off ALL outputs and will go into a fault
mode with a brief audio indication.
BURNER IGNITION CONTROL - This routine monitors the ignition control and gas valve return signal in
comparison to the direct spark ignition (DSI) purge time set in PL13. If the gas valve return signal from the
ignition control has not turned on or has disengaged prior to the expiration of the DSI purge time set in PL13, the
controller will interrupt the cycle and will display “Burner Ignition Control Fault” condition. If the basket (tumbler)
temperature is above 100° F (38° C), the dryer will continue to display “Burner Ignition Control Fault” while the
dryer cools by running with no heat for 2 minutes or until the temperature drops below 100° F (38° C). Once the
basket (tumbler) temperature is below 100° F (38° C), the controller will shut off ALL outputs and will go into a
fault mode with a brief audio indication.
IGNITION FAULT - After the controller receives a gas valve return signal within the DSI purge time, the
controller will begin a DSI proof time. The controller will continue to recheck the gas valve return signal, if signal
is lost during the DSI proof time, the controller will turn off the heat output and will determine what the retry
count in PL14 is set at. If the retry count is greater than zero, the controller will wait 20-seconds and will attempt
to reignite the flame. If the failure condition occurs again, the controller will retry until the retry count in PL14
has been satisfied. Once the retry count has been satisfied, the controller will interrupt the cycle and will display
“Ignition Fault” condition. If the basket (tumbler) temperature is above 100° F (38° C), the controller will
continue to display “Ignition Fault” while the dryer cools by running with no heat for 2 minutes or until the
temperature drops below 100° F (38° C). Once the basket (tumbler) temperature is below 100° F (38° C), the
controller will shut off ALL outputs and will go into a fault mode with a brief audio indication.
FLAME FAULT - After the controller has verified that the gas valve signal was present throughout the DSI
purge time and the DSI proof time, the controller will continue to monitor the gas valve return signal. In the event
that the gas valve return signal is lost anytime after the DSI proof time, the controller will turn off the heat output
and will increment a counter. Once this fault condition occurs five (5) consecutive times, the controller will
interrupt the cycle and will display “Flame Fault” condition. If the basket (tumbler) temperature is above 100° F
(38° C), the controller will continue to display “Flame Fault” while the dryer cools by running with no heat for 2
minutes or until the temperature drops below 100° F (38° C). Once the basket (tumbler) temperature is below
100° F (38° C), the controller will shut off ALL outputs and will go into a fault mode with a brief audio indication.
56
CLEAN LINT - This routine monitors the opening of the lint drawer switch and compares the time between
openings to the lint cleaning frequency set in PL14. This routine will first prompt the user to clean lint before
locking out the dryer. Once the time between cleanings is equal to the setting in PL14, the display will prompt the
user to clean lint. The lint cleaning frequency limits the amount of time the dryer will run before the microprocessor
locks the dryer out for further use. Once the lint count is reached, the lint drawer must be opened for at least
3-seconds in order to reset the counter. If the lint drawer is not cleaned within 2 hours, the control will be locked
out.
CHECK MAIN FUSE - This routine identifies the opening of the main fuse (fuse 2) on the Phase 7 control
board. If the fuse has opened, the microprocessor will not allow a cycle to begin and will display “Check Main
Fuse” condition. If coins are entered, the credit will be accumulated as it should, however, it will not be applicable
to a cycle until the error has been corrected. If the fuse has opened after the cycle has begun, it will still trigger
the check main fuse fault. The dryer will run with no heat for 2 minutes or until the basket (tumbler) temperature
drops below 100° F (38º C). If the basket (tumbler) temperature is below 100° F (38° C), the controller will shut
off ALL outputs and will go into a fault mode with a brief audio indication.
EXHAUST TEMPERATURE SENSOR FAULT/AXIAL TEMPERATURE SENSOR FAULT - This
routine indicates a problem with the temperature sensor circuit. This error will trigger an “Exhaust Probe Fault
or Axial Probe Fault” condition. The dryer will run with no heat for 2 minutes or until the basket (tumbler)
temperature drops below 100° F (38º C). If the basket (tumbler) temperature is below 100° F (38° C), the
controller will shut off ALL outputs and will go into a fault mode with a brief audio indication.
ROTATIONAL SENSOR FAULT - This routine monitors the pulses from the rotational sensor input. It
basically times the dwell between the signals. If the time between the pulses exceeds 8-seconds, the controller
will trigger a “Rotate Sensor Fault” condition. The dryer will run with no heat for 2 minutes or until the temperature
drops below 100° F (38º C). If the basket (tumbler) temperature is below 100º F (38º C), the controller will shut
off ALL outputs and will go into a fault mode with a brief audio indication.
EXHAUST HIGH TEMP FAULT - This error routine indicates a problem with overheating. This error will
initiate an “Exhaust High Temp Fault” condition. The controller determines this error by monitoring the temperature
sensor input to have a steady gradual increase in temperature to a known upper limit (the limit typically is 20º
over the maximum allowed programmable set point). The controller will disengage ALL outputs and will go into
a fault mode with a brief audio indication.
57
B. SENSOR ACTIVATED FIRE EXTINGUISHING (S.A.F.E.) SYSTEM
DIAGNOSTIC MESSAGES
OPEN S.A.F.E. SYSTEM PROBE FAULT - This message indicates that the S.A.F.E. system probe is either
not connected or is damaged.
SHORTED S.A.F.E. SYSTEM PROBE FAULT - This indicates that the S.A.F.E. system probe is shorted
or the wire to the S.A.F.E. system probe is shorted.
S.A.F.E. SYSTEM ACTIVATED OR S.A.F.E. SYSTEM WAS ACTIVATED - This indicates that the
S.A.F.E. system is on. If the S.A.F.E. system is active, the buzzer will be sounded at a fast pace and the
controller will display “S.A.F.E. System Activated.” Once the S.A.F.E. system is deactivated, the controller will
display “S.A.F.E. System was Active” until the dryer is attended to by someone.
OPEN S.A.F.E. SYSTEM VALVE FAULT - This indicates that the water valve is open or that it is not
connected to the control.
SHORTED S.A.F.E. SYSTEM VALVE FAULT - This indicates a problem with the water valve where it has
been shorted out.
WATER NOT CONNECTED - This indicates that there is no water pressure at the water valve. This will
occur if water is not connected to the dryer or if there is low water pressure in the water line coming to the dryer.
58
C. INPUT/OUTPUT (I/O) BOARD LIGHT EMITTING DIODE (L.E.D.)
INDICATORS
1. INPUTS
H2O – (RED L.E.D.)
This L.E.D. will indicate the status of the water pressure sensor. If the water
pressure is present, the L.E.D. will be ON.
LINT – (RED L.E.D.)
This L.E.D. will indicate the status of the lint drawer. If the drawer is closed,
then the L.E.D. is ON.
MAIN – (RED L.E.D.)
This L.E.D. will indicate the status of the main door. If the door is closed,
then the L.E.D. is ON.
EXHL – (RED L.E.D.)
This L.E.D. will indicate the status of the exhaust high limit disk. If the disk
is closed (temperature below 225º F [107º C]), then the L.E.D. is ON.
SAIL – (RED L.E.D.)
This L.E.D. will indicate the status of the sail switch. If the switch is closed,
then the L.E.D. is ON.
BRHL – (RED L.E.D.)
This L.E.D. will indicate the status of the burner high limit disk. If the disk is
closed (temperature below 330º F [166º C]), then the L.E.D. is ON.
GAS_V – (RED L.E.D.)
This L.E.D. will indicate the status of the gas valve. If the gas valve is open
(ON), then the L.E.D. is ON.
2.
OUTPUTS
DRIVE – (GREEN L.E.D.)
This L.E.D. will indicate the status of the basket (tumbler) forward direction
output. If the request to tumble the basket (tumbler) in the forward direction
is made, then the L.E.D. is ON.
FAN – (GREEN L.E.D.)
This L.E.D. will indicate the status of the fan output. If the request to turn on
the fan (blower) is made, then the L.E.D. is ON.
HEAT – (GREEN L.E.D.)
This L.E.D. will indicate the status of the heat output. If the request to turn
on the heater is made, then the L.E.D. is ON.
FSS – (GREEN L.E.D.)
This L.E.D. will indicate that the S.A.F.E. system is active.
59
D. KEYBOARD (TOUCH PAD) LAYOUT
1. Liquid Crystal Display
2. HI Button
3. PERMANENT PRESS Button
4. LO Button
5. PAUSE Button
60
CGA113189
1 - 05/15/03-15
Download PDF