Manual - High Tech Pet Products

Fully Automatic
Sliding Glass Pet Door
INSTALLATION INSTRUCTIONS
U.S. PATENT # 5,872,516
INTRODUCTION
Product Description:
Your new POWER PET Electronic Pet Door is like no other pet door made.
Patented POWER PETTM electronic pet doors are fully automatic, motor driven and open completely under their own power. Activated by
an ultrasonic pet collar, your new POWER PET door will keep out stray
animals. It is secure against wind, rain, cold and snow and provides much
better insulation than a conventional flap door. Your new POWER PET
door features an attractive, high-strength door panel that quickly and
quietly powers upward disappearing into the stylish housing. Your pets
are empowered to come and go as they please while their animal friends
are politely asked to stay out.
BATTERY
COMPARTMENT
CONTROL PANEL
(BATTERY OPTIONAL)
HIGH STRENGTH
ABS COMPOSITE
HOUSING
MOUNTING SCREW
COVERS (8)
DOOR PANEL
Power Input
Jack
Power Input
Jack
ULTRASONIC SENSOR
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
3
POWER PET doors increase home security with a special automatic, deadbolt locking feature that guards against would-be intruders. Only the
coded signal from your pet’s collar will open the Power Pet door.
Only Power Pet doors feature an ingenious directional sensing system
that operates a fully automatic, motor driven panel. The signal emitted
from your pet’s collar tells the Power Pet door how far away your pet is
and the direction in which your pet is traveling. This allows the Power
Pet to work like magic, opening only when your pet is on a direct approach, not when it is just wandering by and not when it is sitting or
sleeping next to the door.
ALL NEW DESIGN!
After selling thousands of our original POWER PET, PP
models we are very pleased to introduce our All New, completely redesigned and restyled PX Model. We listened to
the feedback of hundreds of customers and threw in a few
ingenious, new ideas of our own to bring you the ultimate
combination of security, style and convenient features.
The PX model, which features an extremely slim design, is
less than 2 inches deep. This allows it to be ­mounted flush
to your door or wall. You cut a hole only as large as the door
panel itself, then mount your POWER PET door in front of
the opening. You will find it is actually easier to install a
POWER PET door than a conventional pet door and certainly
easier than installing a “between the studs type door”
The PX is constructed of an ultra-high strength ABS composite housing with a bullet-proof Lexan plastic door panel, giving you
and your pet the ultimate in security. The Lexan panel is mounted on a
sliding, air-tight seal for the best wind, rain and foul weather protection
of any pet door made.
This new, absolutely state of the art design represents unquestionably
the most advanced, most reliable, most stylish pet door made anywhere.
In fact, your new POWER PET Fully Automatic Pet Door will be the most
sophisti­cated appliance your pet will ever own!
___________________________________________________________________________________________
4
www.hightechpet.com
High Tech Pet Products, Inc.
Your POWER PET door package includes:
• O
ne Pet Transmitter Collar (Model MS-4 or MS-5 Ultrasonic
­Transmitter Collar)
• 1
10 volt AC Adapter (connects to either Power Input Jack on edge of
inside frame)
• Pre-Fabricated Outside Frame
• All Required Hardware
(Wall Adapter Tunnel, Rechargeable Battery, Battery Charger Kit and Extra
Transmitter Collars are sold separately.)
PET COLLAR
­OPERATED
Only the amazing POWER
PET door uses our Patented
directional ultrasonic sensing system. This system
has great advantages over
magnetic or radio transmitter collars.
Ultrasonic
Collar
Directional
Signal
Microphone
agnetic collars have a
M
very limited range making
it tough to train the pet to
­operate the door. Radio
systems have good range but
open whenever the animal is
within that range, even if the
pet is sitting, sleeping or just
wandering by.
The Power Pet’s directional ultrasonic system overcomes these problems. The Pet worn ultrasonic collar emits a highly directional signal,
which is received by the microphone only when your pet is directly facing the door opening. The unit is not likely to trigger if your pet is just
wandering by.
Typically the ultrasonic signal is bounced off the ground in the direction which your pet is facing. This means that surfaces which are highly
reflective such as tile and linoleum will result in a longer working range
than acoustically absorbent surfaces such as carpeting. Consult the
ADJUSTING RANGE CONTROLS section for instructions on setting the
desired opening range.
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
5
INSTALLATION
POWER PET Electronic Pet Door Sliding Glass Insert
High Tech Pet has incorporated their amazing fully automatic POWER
PET door into a stylish sliding glass door panel that can be easily
­installed right alongside your exising sliding glass door.
Your sliding glass POWER PET door is pre-installed in the sliding glass
insert, which means your installation takes just minutes.
1. Insert the pre-made glass panel
onto the track of your sliding
glass door. (Figure 1)
FIGURE 1
2. Release the spring loaded top with
the 2 thumbscrews and it
­automatically ­adjusts itself to the
height of your door. (Figure 2)
3. Push the panel against the inner wall
and tighten the thumbscrews. (Figure 2)
FIGURE 2
4. Carefully peel and apply the weather stripping
along the edge of the POWER PET door to
provide a seal between the POWER PET door
and the sliding glass door. (Figure 3)
FIGURE 3
___________________________________________________________________________________________
6
www.hightechpet.com
High Tech Pet Products, Inc.
High Tech Pet does not stop at weather stripping. Our sliding glass doors
must meet our rigid standards of weather resistance, so we go a step
further and ­supply a draft stopper!
5. A
pply the draft stopper to the back
of your s­ liding glass door. (Figure 4)
FIGURE 4
6. Peel the clear protective adhesive from the ­outside tinted door.
Installing the Locking Pin
1. Before mounting the locking mechanism, remove any screws that
might obstruct attachment on your sliding door.
2. P
osition locking pin as low as
possible on the edge of the sliding door while still being able to
push and pull the pin for locking
and release. Mark where a hole
should be drilled in the stationary sliding door to accept the pin
when the sliding door is closed
tightly against the PX-SGL Pet
Door. (Figure 5)
FIGURE 5
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
7
3. D
rill the hole first using a 1/8 inch drill
bit and then ­finishing with a 1/4 inch
drill bit. (Figure 6) Be careful to not
­penetrate the drill bit beyond the frame
­material (aluminum or PVC). ­Drilling too
deep may damage the glass or the glass
seal. Drill just deep enough to create a
1/4 inch hole for the pin to engage.
FIGURE 6
4. Insert the lock pin in the drilled hole
and hold the lock in position while
you mark the two mounting slots
on the edge of the sliding door.
(Figure 7)
When doing this, position the lock
so that it will not interfere with
anything while opening and closing
the door.
FIGURE 7
5. Remove the lock and using a 1/8 inch
drill bit, drill pilot holes for two screws
to hold the lock to the sliding door.
(Figure 8)
Drill only deep enough to produce a
hole in the sliding door frame. Drilling
too deep may damage the glass or
glass seal.
FIGURE 8
___________________________________________________________________________________________
8
www.hightechpet.com
High Tech Pet Products, Inc.
6. Position the lock with the pin e
­ xtended
into the 1/4 inch hole, and fasten the
lock to the door using two s­ upplied self
tapping screws. (Figure 9)
Operation: Pull the pin to allow opening of the door. Close the door and
push in the pin to lock the door closed.
FIGURE 9
Y
our High Tech Pet Fully Automatic
Power Pet Door is now installed and
ready for you and your pet to enjoy.
Installed Fully Automatic
­Sliding Glass Power Pet Door
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
9
Now, set your desired range and access per your user manual.
You and your pet are now ready to enjoy the freedom and beauty of
your POWER PET sliding glass door.
If you still have questions, give us a call at 800-255-1279 and, together,
we’ll make sure your pets can enjoy the life they deserve.
Initial Power up
Plug the AC Adaptor into a nearby 110 VAC wall outlet. Plug adaptor cord
into the left or right Power Input Jack on the inside frame. (see page 3)
Press the front panel ON button to power up the door. Verify the AC
light is illuminated.
Press the manual OPEN button and verify the door panel opens and
closes by itself.
AC and Battery Operation
(In Battery Back Up Mode the
Door Automatically Switches
to Battery if AC Power Is Lost.)
Manual Open Button
Automatic Battery
Power Monitoring
Dual Range Controls
For Independant Control of
Inside and Outside Distance
4 Way Access Control
In and Out
In Only
Out Only
Closed
___________________________________________________________________________________________
10
www.hightechpet.com
High Tech Pet Products, Inc.
Battery Installation
To install the battery, open the battery compartment, and align the two
battery lugs with the two lug sockets on the inner wall of the battery
compartment. Then press the battery to mate it to the sockets. When
done the battery should be flush with the wall, and the compartment
cover should fit comfortably over the installed battery.
An installed battery is automatically charged whenever the AC Adaptor is
powering the door.
Battery Status Indicators
The OK light is illuminated when the battery is more than one-third charged.
The LOW light illuminates when the battery is less than one-third
charged.
Note that during door opening these indicators may reverse for a
few seconds when the battery is below one-half charge. This is normal and gives a little advance notice of an impending low battery.
Battery Operation
Whenever AC Power is unavailable and a charged battery is installed, the
front panel indicators go into a low power mode where they blink every
four seconds instead of remaining on continuously. This feature allows
the battery to power the door for up to two months or 500 openings.
ADVANCED FEATURES
INTRINSICALLY SAFE OPERATION
The POWER PET electronic pet door is intrinsically safe. It uses an
electric motor and cable drive to lift the door panel. The panel remains
open until the pet collar signal is gone, indicating that your pet is clear
of the opening. When the pet collar signal is gone, power to the motor is
turned off and the panel is returned by the force of gravity only. Downward speed is reduced by an electronic brake applied to the reverse motion of the motor. This brake operates with or without electrical power.
Because the panel is returned by simple gravity, the maximum force
that can be applied by the panel when it is closing is limited to its own
weight. The door panel weighs only about 2 lbs.
AUTO RETRACT FEATURE
As an added safety feature, the POWER PET also has a sensing system
that automatically raises the panel should it ­encounter an obstruction
on the way down. This feature can be defeated in the unusual case that
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
11
binding or other restriction slows the door closure to the point that it unnecessarily retracts. See the AUTOMATIC SAFETY RETRACT Section for
more information.
AUTO DEAD BOLT LOCKING FEATURE
The POWER PET door uses a spring loaded locking pin which automatically snaps into its retaining hole when the movable panel comes to rest in
the closed position. The pin can only be released when the motor applies
tension to the cable. This makes it impossible for even the most clever
animals (and people) to raise the panel mechanically.
THREE DIFFERENT POWER CHOICES: Your new POWER PETTM Door may
be operated in three different power modes.
1. 110 volt AC Wall Outlet: Your standard POWER PETTM Door comes standard with a U.L. approved AC adapter. Plug the adapter into a nearby
wall outlet for continuous operation.
2. AC with Battery Back-up: You may purchase an optional rechargeable battery for use along with your AC adapter. If your household
­electricity should ever fail, your POWER PETTM Door will automatically
switch over to battery operation. When power is restored, the AC
adapter will automatically recharge your battery.
3. Full Battery Operation: You may also operate your POWER PETTM Door
with the battery only. This eliminates the need for the AC adapter or
any electrical power connection. However, you will need to recharge
the battery periodically. ­(Recharge interval varies depending upon
use.) In this case, we recommend that you purchase the optional
­battery and a battery charger kit. With the charger kit you get a battery charger and an extra battery. Use one battery in your POWER
PETTM Door and keep the other in the charger. When your door battery
runs low, just swap.
DUAL RANGE CONTROLS: Individual range control to allow you to adjust
different activation distances for inside and outside of your home. (Usually, it’s a good idea to use a short distance of a foot or two inside, and a
longer 4 to 5 foot distance outside.) Your new POWER PET PX gives you
full control. Note: range markings on the door are not in units of distance,
but rather in signal strength. A marking of 10 produces the maximum
distance.
___________________________________________________________________________________________
12
www.hightechpet.com
High Tech Pet Products, Inc.
Adjusting the Range
When you first install the POWER PET PX door, pre-set both RANGE
Controls - one at a time - to the desired activation distance as follows:
- Enable just the INSIDE or OUTSIDE sensor and set that RANGE ­control
to zero.
- Hold the collar at about your pet’s height, pointing down toward the
­bottom of the door and at the desired activation distance from the
door.
- Slowly increase that RANGE Control setting until the panel opens.
- Repeat this for the other sensor.
- Now put the collar on the pet and, if necessary, readjust the RANGE
settings slightly to achieve the desired opening distance.
Just as your hearing of a conversation can be overpowered by loud
­noises such as a lawn mower, the door sensors can also be overpowered
by loud ultrasonic noises. Specifically some sprinklers, lawn mowers and
vacuum cleaners can put out enough noise to temporarily mask the collar
signal. The POWER PET PX door has a unique feature which indicates
when the background noise level is too high. Whenever the INSIDE noise
is too loud, the INSIDE light will flicker or flash on. This means you may
want to decrease the INSIDE knob setting slightly. Likewise, whenever
the OUTSIDE noise is too high, the OUTSIDE light will flicker or flash
on. This means you may want to decrease slightly the OUTSIDE knob
­setting. A little flickering once in a while is normal. A lot of flickering or
continuous flashing means the knob is set too high.
4 WAY ACCESS CONTROL: Individual activation buttons for the inside
and outside sensors give you a 4-way access control system. You can
allow your pet to come in but not go out, go out but not come in, come in
and out or close and lock the door altogether
AUTOMATIC CLOSE CONTROL: Your POWER PET PX Features a smart
sensing circuit that keeps the door panel open as long as it is receiving
the signal from your pet’s collar. Once your pet has moved completely
through the opening, the panel closes.
ADJUSTABLE HOLD UP TIME: The door is held open for a short time to
let the pet get fully through the door before it starts closing. Depending
on the speed your pet moves, you may adjust the hold up time as follows.
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
13
1. Press OFF button
2. Press and hold one or both sensor
buttons to select hold up time
3. Press OFF button
to save this hold up
time
4. Press ON button to
power the door.
When shipped from the factory the hold up time is set to 4 seconds. We
recommend you initially introduce your pet to the door with a long hold
up time. Later you can reduce the hold up time if desired.
HOLD OPEN FEATURE: A new feature introduced in 2012 allows the
door to be manually opened and stay open for any length of time.
If you wish to leave the door open for an extended time period, use the
Hold Open Mode, as follows. The door panel will remain open as long as
power is available.
The opening motor is energized the entire time the door is open. So
if using only a battery to power the door, and you do not have an AC
Power Adaptor plugged into the door, use this feature sparingly to keep
from discharging the battery in just a few hours.
___________________________________________________________________________________________
14
www.hightechpet.com
High Tech Pet Products, Inc.
AUTOMATIC SAFETY RETRACT: Your POWER PET PX is intrinsically safe
for all pets and people, including small children. The door panel weighs
less than 2 lbs. and is closed smoothly by gravity (not the motor) and is
too light to cause any physical injury. However, just to be doubly safe
around infants, we’ve included an automatic safety retract feature. This
feature causes the panel to instantly retract if it encounters an obstruction during closure.
DEFEATING THE AUTOMATIC SAFETY RETRACT: Under unusual
conditions, such as a warped wall mounting, the door sometimes
may close so slowly that the auto-retract feature triggers the door to
re-open unnecessarily. In these cases it may be desirable to defeat
the Automatic Safety Retract feature. Do this by first pressing the
OFF button to turn off the door controls and all the lights. Leave the
door powered by the wall wart or battery when you do this. Then
while holding down the MANUAL OPEN button, press and release the
OUTSIDE SENSOR button. The OUTSIDE light will blink to indicate the
feature has been disabled.
ENABLING AUTOMATIC SAFETY RETRACT: Similarly you may enable the Automatic Safety Retract feature at any time. Do this by first
pressing the OFF button to turn off the door controls and all the lights.
Leave the door powered by the wall wart or battery when you do this.
Then while holding down the MANUAL OPEN button, press and release
the INSIDE SENSOR button. The INSIDE light will blink to indicate the
feature has been enabled. When shipped from the factory, the automatic safety retract feature is enabled.
After Defeating or Enabling the feature, press the POWER ON button
to resume normal door operation.
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
15
PET COLLAR OPERATING INSTRUCTIONS
Your POWER PET DOOR comes with a standard model MS-4 or MS-5
ultrasonic transmitter collar. Each collar includes a battery TEST button
which illuminates a red LED when the battery is OK. If the LED fails to
light, battery replacement is necessary.
Note: To energize the MS-4 Collar, pull out and discard the PULL TAB
which is protruding from the side of the collar.
To energize the MS-5 Collar,
1. Pull out the PULL TAB, and discard
2. S
imultaneously squeeze the case
together at both ends until fully
seated.
3. S
crew in the rear screw using the
supplied #1 Phillips screwdriver.
Tighten the screw snuggly but do
not over tighten.
4. P
ress the TEST button and observe the Red Test Light to confirm
operation.
5. If not working, follow the Battery Replacement instruction to open the
case, remove any remaining part of the PULL TAB, and then re-seat
the battery and close up the case.
___________________________________________________________________________________________
16
www.hightechpet.com
High Tech Pet Products, Inc.
ADJUSTING THE STRAP
1. Fasten the collar around your pet’s neck
so that it fits comfortably. In most cases
there will be excess strap length.
2. With a soft pencil or magic marker, mark
the amount of strap to be removed
leaving at least one inch past the D-ring
buckle.
3. Remove the collar from your pet and cut
off the excess strap at the mark.
4. To avoid fraying carefully heat the cut
end with an open flame to melt and fuse
the material.
5. Put the collar on your pet.
Now, set your desired range and access per your user manual.
You and your pet are now ready to enjoy the freedom and beauty of
your POWER PET sliding glass door.
If you still have questions, give us a call at 800-255-1279 and, together,
we’ll make sure your pets can enjoy the life they deserve.
Your High Tech Pet MS-4 or MS-5 transmitter collar will operate for 3 to
5 months on a single, easily replaceable battery.
Replacement batteries, part number B3V1A, are available from
www.hightechpet.com.
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
17
REPLACING THE MS-4 BATTERY
1, Insert screwdriver or knife in end
slot and pry open.
2. Separate top from bottom.
3. Replace battery top with the metal
ring visible.
4. C
arefully mate top and bottom
while keeping aluminum speaker
centered in the top hole. Squeeze
together the top and bottom until
both ends snap.
___________________________________________________________________________________________
18
www.hightechpet.com
High Tech Pet Products, Inc.
REPLACING THE MS-5 BATTERY
1. Unscrew the bottom cover.
2. Pry bottom from top on ends and
on ­edges using small flat blade
screwdriver
3. Remove bottom, note ­battery orientation
4. Remove and replace B3V1A battery
5. With new battery installed, close case. Squeeze until
bottom flush with top, by squeezing top and bottom
together
6. Insert and tighten screw.
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
19
WATER RESISTANCE
The High Tech MS-4 ultrasonic transmitter collar is water resistant meaning
that rainy weather and humidity will not damage the unit. These collars are
NOT designed to be fully immersed in water. Should this occur, simply open
the unit, shake out water and let dry. In most cases the unit will function
normally. However the life of the battery will likely be reduced or the battery may require replacement.
The MS-5 collar is fully waterproof to a 3 foot depth.
TRAINING YOUR PET
Training your pet to use its new POWER PET door should be a relatively
­effortless task. Some pets may become startled by the sound and movement of the panel, but be patient. Nearly every pet will soon be used to the
POWER PET’S operation and learn to love using its own personal entry. We
recommend that you lead your pet to the door and allow it to open several times to teach the animal the cause and effect relationship between
pet and door. Then place a food reward on the opposite side and lead the
animal through the opening, allowing it to get the reward on the other side.
Repeat several times. Before too long your pet will get the idea. If your pet
doesn’t get it in one sitting, remain patient and let your pet just walk around
on its own for awhile. It won’t take too much more time for your pet to
realize the POWER PET opens whenever the pet comes its way. One of the
most frequent comments we hear from POWER PET owners is how much
their pets love using their POWER PET door. We are sure your pet will feel
the same!
REPLACEMENT PARTS
Over the years you may need to replace damaged or worn out parts. High
Tech Pet Products offers complete refurbishment of the door at our facility
in Ventura CA. Contact Customer Service for instructions on shipping your
door back to us. For customers with the mechanical skills to refurbish themselves, we offer many replacement parts on our web site, www.hightechpet.
com along with do-it-yourself instructions.
___________________________________________________________________________________________
20
www.hightechpet.com
High Tech Pet Products, Inc.
MANY CONVENIENT ACCESSORIES!
We’ve added all sorts of great new options to make your POWER PET PX
the most versatile pet door you’ll find.
W
ER
P ET D O
Y
SO
PO
EXTRA PET COLLARS:
A
RD
Model MS-4 or MS-5 Ultrasonic
Transmitter Collar
You may wish to purchase an Extra collar for each additional pet and keep one
or two more as spares. Lightweight and
comfortable on all cats and dogs.
OR
UN
D B A R R IE
R
These collars will operate all our
­ULTRASONIC devices including:
• P
OWER PET Fully Automatic Pet
Doors
B AR R I E R
• S
OUND BARRIER Non-Shock, Indoor
Sonic Fence
M
AN
E C O N T AI
N
W
ER
P ET D O
Y
SO
PO
HU
• Y
ARD BARRIER Non-Shock, ­Outdoor
Sonic Fence.
RA
A
RD
UN
OR
D B A R R IE
B AR R I E R
DIO M A T
R
Model RX-10 Optional
­Multi-Function Collar
Our ingenious Model RX-10 Multifunction Collar combines the ultrasonic
transmitter function of the Ultrasonic
model pet collar above with our radio
receiver and shock stimulus ­technology
to ­operate ALL our products including:
TOTAL PET CONTROLTM COMPATIBLE
•P
OWER PET Fully Automatic Pet Doors
• SOUND BARRIER Non-Shock, Indoor
Sonic Fence
• YARD BARRIER Non-Shock Outdoor
Sonic Fence
• HUMANE CONTAIN Electronic Pet
Fence
• RADIO MAT Electronic Scat Pad
You may add any of these collars to your POWER PET Door order to
­c___________________________________________________________________________________________
onfigure your own custom electronic pet care ­system!
High Tech Pet Products, Inc.
www.hightechpet.com
21
Wall Adapter Tunnel: Install your POWER PETTM
door on any wall in one easy step with our convenient WALL ADAPTER TUNNEL accessory which
extends the passageway and provides a sealed professional installation. It fits snugly into the POWER
PETTM door main frame on one side of the wall, and
the POWER PETTM outside frame on the other side.
Adapts to any wall thickness from 4” to 8” thick.
Rechargeable Backup Battery: Install this heavy
duty, long life, sealed 12 volt rechargeable battery
in your POWER PETTM door to provide back-up power
in case of an AC power failure. Provides hundreds
of door openings to let your pet in or out until power
returns. Automatically recharges in your door when
power is restored.
Battery Charger Kit: For battery powering of the
POWER PETTM Door in installations where AC power
is not available. This kit includes a battery charger,
rechargeable battery and an AC adapter. Simply
charge the battery for 12 hours and insert it in the
door to provide one to four weeks of normal operation. For the ultimate in convenience we recommend
that you purchase this kit and one extra rechargeable battery above. Use one battery in your POWER PETTM door and keep
the other in the charger. When your door battery runs down just swap in
less than 30 seconds!
___________________________________________________________________________________________
22
www.hightechpet.com
High Tech Pet Products, Inc.
ND
B A R RIE
R
R
A
A R RIE
DB
R
NE
CONTA
HU
M
YA
SO
U
TOTAL PET CONTROL ACCESSORIES:
RA
DIO M AT
IN
SOUND BARRIER
Model SBR-1 Indoor Sonic alarm keeps your pet off
furniture, away from the kitchen table or out of
an entire room. Operated from your pet’s MS-4 or
MS-5 transmitter included with your POWER PET
Door. Also, operated by the optional RC-7000X
­collar. Order one for each pet restricted area.
YARD BARRIER
Model YBR-1 Outdoor Sonic Alarm keeps your pet
out of the garden, away from the trash and out
of restricted areas with a wall of sound. Operated
from your pet’s standard MS-4 transmitter included with your POWER PET Door. Also, operated by
the optional RC-7000X collar. Order one for each
part of your yard where pets don’t belong.
HUMANE CONTAIN
Model HC-7000X Simply, the Most Advanced,
Most Effective, Most Humane electronic pet fence
made. Complete Electronic Fence Super System
includes one Model RC-7000X Multi-Function
Pet Collar that controls your POWER PET Door and
every other TOTAL PET CONTROLTM COMPATIBLE
product we make. Order additional collars for
­additional pets.
RADIO MAT
odel RM-1TX Radio Controlled Scat Pad, Keeps
M
Fido off the furniture! Radio signal emitted by
the paw pad triggers a shock at Fido’s collar. Also
works in non-shock, sound only mode. Requires
one Model RC-7000X Multi-Function Pet Collar
that controls your POWER PET Door and all our
TOTAL PET CONTROLTM COMPATIBLE products.
Order one pad for every piece of furniture or other
area where Fido doesn’t belong. Order additional
collars for additional pets.
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
23
TROUBLESHOOTING GUIDE
For each problem, start with 1st solution, then 2nd, etc., until solved.
PROBLEMSOLUTIONS
While opening, door stops rising
and all lights turn off or blink
1) Replace power supply
Door panel goes up and down
without stopping
1) Replace main wire harness
Very short range on both
­sensors
1) Replace sensor cable
utside sensor good, but inside
O
sensor yields short or no range
2) Replace motor
2) Replace main circuit board
2) Replace main circuit board
Inside sensor good, but ouside
sensor yields short or no range
Manual button works, but inside and outside sensors yield
short or no range
Manual button works, but door
is not triggered by collar
Door goes up too slowly
Door sticks at top
1) Loosen mounting screws
slightly
2) Clean sliding door with soap
and water, then spray with
dry lubricant
3) Replace motor assembly
4) Replace main circuit board
Door sometimes opens by itself
1) Reduce range settings on
front panel
Door does not open with
manual button or collar
1) Replace main circuit board
Multiple collar failures
1) Upgrade to MS-4 or MS-5
collar
Range is difficult to adjust to
less than five or six feet
1) Replace main circuit board
___________________________________________________________________________________________
24
www.hightechpet.com
High Tech Pet Products, Inc.
If replacing an internal component, here are the workings of
the door you will see after removing the back of the door
frame.
MAIN CIRCUIT
BOARD
MOTOR ASSEMBLY
CABLE GUIDE
MAIN WIRE
HARNESS
& SENSOR CABLE
LIFT CABLE
POSITION
SWITCHES
(PART OF MAIN
WIRE HARNESS)
LOCKING PIN
SLIDING DOOR
PANEL
RIGHT
POWER PLUG
(PART OF MAIN
WIRE HARNESS)
LEFT
POWER PLUG
(PART OF MAIN
WIRE HARNESS)
MICROPHONES
(PART OF SENSOR CABLE
ASSEMBLY)
___________________________________________________________________________________________
High Tech Pet Products, Inc.
www.hightechpet.com
25
NOTES
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________ _____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
NOTES
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________ _____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
ORDER INFORMATION
To order extra collars and accessories please visit our website at
www.hightechpet.com or call 1 (800) 255-1279
High Tech Pet Products, Inc.
2476 Palma Drive, Suite A
Ventura, CA 93003
www.hightechpet.com
Rev. II – 12/12/2012
px-sgl-manual
Download PDF