DPharp HART 5/7 Communication Type (EJX A, EJA

User’s
Manual
DPharp
HART 5/7 Communication Type
(EJXA, EJAE)
IM 01C25T01-06EN
IM 01C25T01-06EN
3rd Edition
i
DPharp
HART 5/7 Communication Type
(EJXA, EJAE)
IM 01C25T01-06EN 3rd Edition
Contents
1.
2.
3.
Introduction................................................................................................ 1-1

Regarding This Manual..................................................................................... 1-1
1.1
Safe Use of This Product ................................................................................. 1-2
1.2
Warranty.............................................................................................................. 1-2
1.3
ATEX Documentation........................................................................................ 1-3
Connection................................................................................................. 2-1
2.1 Integral Indicator Display When Powering On............................................... 2-1
2.2 HART Protocol Revision................................................................................... 2-1
2.3
Device Description (DD) on a Configuration Tool and
Transmitter Device Revision............................................................................ 2-2
2.4
Set the parameters using DTM......................................................................... 2-3
2.5
Interconnection Between DPharp and the HART Configuration Tool......... 2-4
2.6
Power Supply Voltage and Load Resistance.................................................. 2-4
Parameter Setting...................................................................................... 3-1
3.1
3.2
3.3
Menu Tree........................................................................................................... 3-1
3.1.1
For DD (HART 5/HART 7) and
DTM (HART 7/EJA series: HART 5)................................................... 3-1
3.1.2
For DTM (EJX series: HART 5).......................................................... 3-8
Basic Setup....................................................................................................... 3-12
3.2.1
Tag and Device Information.............................................................. 3-12
3.2.2
Unit.................................................................................................... 3-12
3.2.3
Range Change.................................................................................. 3-13
3.2.4
Output Mode..................................................................................... 3-13
3.2.5
Damping Time Constant Setup......................................................... 3-13
3.2.6
Output Signal Low Cut Mode Setup................................................. 3-14
3.2.7
Impulse Line Connection Orientation Setup..................................... 3-14
3.2.8
Static Pressure Setup....................................................................... 3-15
Detailed Setup.................................................................................................. 3-15
3.3.1
Bi-directional Flow Measurement..................................................... 3-15
3.3.2
Analog Output Signal Adjustable Range.......................................... 3-16
3.3.3
Integral Indicator Display Mode........................................................ 3-16
3.3.4
Integral Indicator Scale Setup........................................................... 3-16
3.3.5
Unit for Displayed Temperature........................................................ 3-18
3rd Edition: June 2012 (KP)
All Rights Reserved, Copyright © 2010, Yokogawa Electric Corporation
IM 01C25T01-06EN
ii
3.3.6
Sensor Trim....................................................................................... 3-18
3.3.7
Trim Analog Output........................................................................... 3-20
3.3.8
External Switch Mode....................................................................... 3-20
3.3.9
CPU Failure Burnout Direction and Hardware Write Protect........... 3-21
3.3.10
Software Write Protection................................................................. 3-21
3.3.11
Signal Characterizer......................................................................... 3-22
3.3.12
Alarm................................................................................................. 3-22
3.3.13
Status Output (only for EJX series: option code AL)........................ 3-23
3.3.14
Capillary Fill Fluid Density Compensation ....................................... 3-24
3.3.15
Test Output, Simulation, and Squawk............................................... 3-25
3.3.16
Burst Mode........................................................................................ 3-27
3.3.16.1 In the case of using HART 5............................................ 3-27
3.3.16.2 In the case of using HART 7............................................ 3-27
3.3.17
Multidrop Mode................................................................................. 3-32
3.3.17.1 In the case of using HART 5............................................ 3-32
3.3.17.2 In the case of using HART 7............................................ 3-33
3.3.18
4.
Switching HART Protocol Revision.................................................. 3-33
Diagnostics................................................................................................ 4-1
4.1
4.2
Self-Diagnostics................................................................................................. 4-1
4.1.1 Identify Problems by Using the HART Configuration Tool.................. 4-1
4.1.2
Checking with Integral Indicator.......................................................... 4-2
4.1.3
Status information available for HART 7............................................. 4-2
Advanced Diagnostics (Only for EJX series)................................................. 4-3
4.2.1
Multi-sensing Process Monitoring....................................................... 4-3
4.2.2
Impulse Line Blockage Detection (ILBD)............................................ 4-3
4.2.2.1
Blockage Detection............................................................ 4-6
4.2.2.2
Combination of Reference Result and
Blockage Detection............................................................ 4-8
4.2.2.3
Operation Parameters....................................................... 4-9
4.2.2.4
Operating Procedure....................................................... 4-11
4.2.2.5
Alarm and Alert Setting.................................................... 4-12
4.2.2.6
Condition Check.............................................................. 4-14
4.2.2.7
Obtain Reference Values................................................. 4-15
4.2.2.8
Capability Test of Blockage Detection Operation............ 4-16
4.2.2.9
Start ILBD Operation....................................................... 4-16
4.2.2.10 Tuning.............................................................................. 4-17
4.2.2.11 Reset of Reference Value................................................ 4-18
4.2.2.12 ILBD Parameter List........................................................ 4-19
4.2.3
4.3
Heat Trace Monitoring...................................................................... 4-21
4.2.3.1
Flg Temp Coef Setting..................................................... 4-21
4.2.3.2
Out of Temperature Measurement Range....................... 4-22
4.2.3.3
Parameter Lists for Heat Trace Monitoring...................... 4-23
Alarms and Countermeasures....................................................................... 4-24
IM 01C25T01-06EN
iii
5.
Parameter Summary................................................................................. 5-1
Appendix 1. Safety Instrumented Systems Installation.............................A1-1
A1.1
Scope and Purpose........................................................................................ A1-1
A1.2
Using the transmitter for an SIS Application............................................... A1-1
A1.2.1
Safety Accuracy................................................................................A1-1
A1.2.2
Diagnostic Response Time...............................................................A1-1
A1.2.3
Setup.................................................................................................A1-1
A1.2.4
Required Parameter Settings...........................................................A1-1
A1.2.5
Proof Testing.....................................................................................A1-1
A1.2.6
Repair and Replacement..................................................................A1-2
A1.2.7
Startup Time......................................................................................A1-2
A1.2.8
Firmware Update..............................................................................A1-2
A1.2.9
Reliability Data..................................................................................A1-2
A1.2.10 Lifetime Limits...................................................................................A1-2
A1.2.11 Environmental Limits........................................................................A1-2
A1.2.12 Application Limits..............................................................................A1-2
A1.3
Definitions and Abbreviations....................................................................... A1-3
A1.3.1
Definitions.........................................................................................A1-3
A1.3.2
Abbreviations....................................................................................A1-3
Appendix 2. ILBD Check List.........................................................................A2-1
Revision Information................................................................................................i
IM 01C25T01-06EN
1.
1-1
<1. Introduction>
Introduction
Thank you for purchasing the DPharp EJX
series pressure transmitter/EJA series pressure
transmitter(“transmitter”).
The transmitters are precisely calibrated at the
factory before shipment.
To ensure both safety and efficiency, please
read this manual carefully before operating the
instrument.
This manual describes the HART protocol
communication functions of the transmitter
and explains how to set the parameters for the
transmitters using the HART configuration tool.
For information on the installation, wiring, and
maintenance of the transmitters, please refer to the
user’s manual of each model.
• Please note that changes in the specifications,
construction, or component parts of the
instrument may not immediately be reflected
in this manual at the time of change, provided
that postponement of revisions will not cause
difficulty to the user from a functional or
performance standpoint.
• The following safety symbols are used in this
manual:
WARNING
Indicates a potentially hazardous situation which,
if not avoided, could result in death or serious
injury.
WARNING
When using the transmitter in a Safety
Instrumented Systems (SIS) application, refer
to Appendix 1 in this manual. The instructions
and procedures in the appendix must be strictly
followed in order to maintain the designed safety
integrity of the transmitter.
 Regarding This Manual
• This manual should be provided to the end
user.
• The contents of this manual are subject to
change without prior notice.
• All rights reserved. No part of this manual may
be reproduced in any form without Yokogawa’s
written permission.
• Yokogawa makes no warranty of any kind with
regard to this manual, including, but not limited
to, implied warranty of merchantability and
fitness for a particular purpose.
CAUTION
Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.
IMPORTANT
Indicates that operating the hardware or software
in this manner may damage it or lead to system
failure.
NOTE
Draws attention to information essential for
understanding the operation and features.
• If any question arises or errors are found, or if
any information is missing from this manual,
please inform the nearest Yokogawa sales
office.
• The specifications covered by this manual are
limited to those for the standard type under the
specified model number break-down and do not
cover custom-made instruments.
IM 01C25T01-06EN
1.1 Safe Use of This Product
For the safety of the operator and to protect the
instrument and the system, please be sure to follow
this manual’s safety instructions when handling this
instrument. If these instructions are not heeded,
the protection provided by this instrument may be
impaired. In this case, Yokogawa cannot guarantee
that the instrument can be safely operated. Please
pay special attention to the following points:
(a) Installation
• This instrument may only be installed by an
engineer or technician who has an expert
knowledge of this device. Operators are not
allowed to carry out installation unless they
meet this condition.
• With high process temperatures, care must
be taken not to burn yourself by touching the
instrument or its casing.
• Never loosen the process connector nuts when the
instrument is installed in a process. This can lead
to a sudden, explosive release of process fluids.
• When draining condensate from the pressure
detector section, take appropriate precautions to
prevent the inhalation of harmful vapors and the
contact of toxic process fluids with the skin or eyes.
• When removing the instrument from a
hazardous process, avoid contact with the
process fluid and the interior of the meter.
• All installation shall comply with local installation
requirements and the local electrical code.
(b) Wiring
• The instrument must be installed by an engineer
or technician who has an expert knowledge of
this instrument. Operators are not permitted to
carry out wiring unless they meet this condition.
• Before connecting the power cables, please
confirm that there is no current flowing through
the cables and that the power supply to the
instrument is switched off.
(c) Operation
• Wait 10 min. after the power is turned off before
opening the covers.
(d) Maintenance
• Please carry out only the maintenance
procedures described in this manual. If you
require further assistance, please contact the
nearest Yokogawa office.
• Care should be taken to prevent the build up of dust
or other materials on the display glass and the name
plate. To clean these surfaces, use a soft, dry cloth.
<1. Introduction>
1-2
(e) Modification
• Yokogawa will not be liable for malfunctions or
damage resulting from any modification made
to this instrument by the customer.
1.2 Warranty
• The warranty shall cover the period noted on
the quotation presented to the purchaser at the
time of purchase. Problems occurring during
the warranty period shall basically be repaired
free of charge.
• If any problems are experienced with this
instrument, the customer should contact the
Yokogawa representative from which this
instrument was purchased or the nearest
Yokogawa office.
• If a problem arises with this instrument,
please inform us of the nature of the problem
and the circumstances under which it
developed, including the model specification
and serial number. Any diagrams, data and
other information you can include in your
communication will also be helpful.
• The party responsible for the cost of fixing the
problem shall be determined by Yokogawa
following an investigation conducted by Yokogawa.
• The purchaser shall bear the responsibility for
repair costs, even during the warranty period, if
the malfunction is due to:
- Improper and/or inadequate maintenance by
the purchaser.
- Malfunction or damage due to a failure
to handle, use, or store the instrument in
accordance with the design specifications.
- Use of the product in question in a location
not conforming to the standards specified by
Yokogawa, or due to improper maintenance
of the installation location.
- Failure or damage due to modification or
repair by any party except Yokogawa or an
approved representative of Yokogawa.
- Malfunction or damage from improper
relocation of the product in question after
delivery.
- Reason of force majeure such as fires,
earthquakes, storms/floods, thunder/
lightening, or other natural disasters, or
disturbances, riots, warfare, or radioactive
contamination.
IM 01C25T01-06EN
<1. Introduction>
1-3
1.3 ATEX Documentation
This is only applicable to the countries in European Union.
GB
DK
SK
CZ
I
LT
E
LV
NL
EST
PL
SF
SLO
P
H
F
BG
D
RO
S
M
GR
IM 01C25T01-06EN
2.
2-1
<2. Connection>
Connection
2.1 Integral Indicator Display
When Powering On
NOTE
For models with the integral indicator code “D”, the
display shows all segments in the LCD and then
changes to the displays shown below sequentially.
LCD display can be set to “All segments display”
only.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM
(EJX:HART 5)
ON
Model name (3 sec.)
All segments display
OFF
[Root Menu] (Refer to subsection
3.1.1) → Detailed setup → Display
condition → Chg power on info
Configuration → Local Display
→ Chg power on info
Show all segments display, Model
name, Communication Protocol, and
Device Revision when powering on.
Show all segments display when
powering on.
2.2 HART Protocol Revision
Communication Protocol (3 sec.)
Device Revision (3 sec.)
F0200.ai
Either “5” or “7” is displayed on the “Communication
Protocol” display as HART protocol revision
followed by device revision number on the “Device
Revision” display.
NOTE
This function is available for software revision
2.02 or later.
Software revision can be checked by the
following procedure.
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
[Root Menu](Refer to subsection
3.1.1) → Review → Software rev
DTM(EJX:HART 5)
Configuration → Device
information1 → Software rev
NOTE
In this User’s Manual, HART protocol revision
5 and 7 are described as HART 5 and HART 7
respectively.
For the models with the output signal code “-J”,
HART protocol revision 5 or 7 is selectable. The
protocol revision is set as specified in the order.
The typical function which is available by HART
protocol revision 7 is listed as follows. Refer to
HART 7 description in this document or HART 7 mark
for detail.
• Long Tag Supporting Up to 32 Characters
Long tag secures a better asset management
with abundant digits in its software.
• Enhanced Burst Mode and Event Notification
Advanced burst mode includes the variety
of transmission setting by specifying burst
variables, update period, and message trigger
mode, and event notification function gives
you alert signal based on the status change in
preset values and self-diagnosis.
• Squawk
Identifying the transmitter by displaying the
particular pattern on LCD
• Multidrop Communication
Up to 63 transmitters can be connected. An
analog signal output available for one device in
a loop.
How to confirm protocol revision is shown below.
There are three ways to confirm the protocol
revision set to the transmitter.
IM 01C25T01-06EN
(1) Confirmation by the name plate
The HART protocol revision is shown by the last
number of the serial number.
Refer to Figure 2.1.
STYLE
MODEL
SUFFIX
SUPPLY
OUTPUT
MWP
mA DC
V DC
CAL
RNG
IMPORTANT
Protocol revision supported by HART
configuration tool must be the same or higher
than that of the transmitter.
Protcol revision
supported by HART
configuration tool
NO.
Made in Japan
TOKYO 180-8750 JAPAN
: Refer to USER'S MANUAL.
XXX - - - XX 
Revision No.
F0201.ai
Output Signal
Code
Revision No.
HART Protocol
Revision
5
HART 5
7
HART 7
-
HART 7
-
HART 5
J
E
Figure 2.1 2-2
<2. Connection>
Name Plate
(2) Confirmation by using integral indicator (When
the integral indicator code is “D”)
Refer to section 2.1.
(3) Confirmation by using HART configuration tool
Follow the procedure below.
1) Connect the configuration tool to the
transmitter.
2)-1 When using DD(HART 5/HART 7) or
DTM(HART 7/EJA: HART 5) configuration
tool.
Select the “Root Menu” (Refer to
subsection 3.1.1)
Call up the “Review” display.
2)-2 When using DTM(EJX:HART 5)
configuration tool.
Call up “HART” display.
Configuration → HART
3) HART protocol revision is displayed on the
“Universal rev” column.
Protocol revision of
the transmitter
5
7
5


7
×

 : Communication OK
×: Communication NG
NOTE
HART 7 communication is supported by
FieldMate R2.02 or later.
NOTE
When the output signal code of the transmitter
is “-J”, HART protocol revision can be changed.
Refer to subsection 3.3.18 about the procedure
of the revision change of HART 5 and HART 7.
2.3 Device Description (DD) on
a Configuration Tool and
Transmitter Device Revision
Before using a HART configuration tool, confirm
that the DD for the transmitter is installed in the
configuration tool.
About the DD, use the device type, device revision
and DD Revision shown in the Table 2.1.
Table 2.1 HART
Protocol
Revision (*1)
5
7
HART Protocol Revision, Device
Revision and DD Revision
DPharp Pressure Transmitter
Model
Name
Device
Type
EJXA
(Except
EJX9A)
EJX
(0x51)
3
3
or later
EJAE
EJA-NEXT
(0x5C)
1
2
or later
10
2
or later
10
1
or later
EJXA
EJX
(Except
(0x3751)
EJX9A)
EJAE
*1:
EJA-NEXT
(0x375C)
Device
DD
Revision Revision
When the output signal code is “–E”, only “5” is available.
IM 01C25T01-06EN
The device revision of the transmitter and DD can
be confirmed as shown below.
If the correct DD is not installed in the configuration
tool, download it from the official web site of HART
Communication Foundation.
(1) Confirming the device revision of the transmitter
● Confirmation by using integral indicator
(When the integral indicator code is “D”)
Refer to the section 2.1
● Confirmation by using HART configuration
tool
Follow the procedure below.
1) Connect the configuration tool to the
transmitter.
2) Select the “Root Menu” (Refer to
subsection 3.1.1)
Call up the “Review” display.
3) The device revision is displayed on the
“Fld dev rev” column.
(2) Confirming the device revision of the
configuration tool
Confirm the device revision from the installed
DD file name according to the procedure
provided for the configuration tool.
The first two digits indicate the device revision
and the next two digits indicate the DD revision.
0 a 0 2. X X X
DD revision
Device revision
NOTE
Device revision of DD file is given in hexadecimal
2-3
<2. Connection>
2.4 Set the parameters using
DTM
When configure the parameters using FieldMate,
use the DTM (Device Type Manager) shown in the
Table 2.2.
Table 2.2
HART
Protocol
Revision
HART Protocol Revision and DTM
DTM
Model
Name
Device
Type
Device
Revision
1.4.160.8
or later*1
EJXA
(Except
EJX9A)
EJX
(0x51)
3
EJA-NEXT
3.3.0.140
HART
or later*2
DTM
EJAE
EJANEXT
(0x5C)
1
EJX
HART7
DTM
3.3.0.140
or later*2
EJXA
EJX_EXP
(Except
(0x3751)
EJX9A)
10
EJA-NEXT
3.3.0.140
HART7
or later*2
DTM
EJANEXT_
EJAE
EXP
(0x375C)
10
Name
EJX V3.1
5
7
*1: *2: DPharp Pressure Transmitter
Revision
The DTM corresponding to this revision is included in
Yokogawa DTM Library HART 2012-2/Device Files
R3.03.03
The DTM corresponding to this revision is included in
Yokogawa Device DTM Library 2.3/Device Files R3.03.03
NOTE
The DTM revision can be confirmed by “DTM
setup”.
Device Files is a Media included in FieldMate.
The user registration site provides Device Files
with the latest update programs.
(URL: https://voc.yokogawa.co.jp/PMK/)
In case update, following operation by “DTM
setup” is required.
• Update DTM catalog
• Assign corresponding DTM to the device
(refer to Table 2.2)
Refer to FieldMate Instruction Manual for detail.
IM 01C25T01-06EN
2-4
<2. Connection>
2.5 Interconnection Between
DPharp and the HART
Configuration Tool
2.6 Power Supply Voltage and
Load Resistance
The HART configuration tool can interface with the
transmitter from the control room, the transmitter
site, or any other wiring termination point in the
loop, provided there is a minimum of 250 Ω
between the connection and the power supply. To
communicate, it must be connected in parallel with
the transmitter; the connections are non-polarized.
Figure 2.2 illustrates the wiring connections for
direct interface at the transmitter site for the
DPharp. The HART configuration tool can be used
for remote access from any terminal strip as well.
When configuring the loop, make sure that the
external load resistance is within the range in the
figure below.
(Note)With an intrinsically safe transmitter, external load
resistance includes safety barrier resistance.
600
External
load
resistance
R (Ω)
R=
E–10.5
0.0244
Communication
applicable range
250
Control room
Relaying
terminals
DPharp
Terminal
board Distributor
0
10.5
16.6
25.2
42
Power supply voltage E (V DC)
Figure 2.3
USB
FieldMate
Modem
PULSE
USB
SUPP
LY
F0203.ai
Relationship between Power Supply
Voltage and External Load Resistance
CHECK
ALARM
PC/FieldMate
HART configuration tool
Figure 2.2
F0202.ai
Connecting the HART Configuration
Tool
IM 01C25T01-06EN
3.
<3. Parameter Setting>
3-1
Parameter Setting
3.1 Menu Tree
The menu tree is different in DD(HART 5/HART 7)/DTM(HART 7/EJA series: HART 5) and DTM(EJX series:
HART 5).
See the menu tree corresponding to the configuration tool.
3.1.1 For DD (HART 5/HART 7) and DTM (HART 7/EJA series: HART 5)
■ DD (HART 5/HART 7)
Root Menu
• Device setup
• Pres
• AO
• LRV
• URV
• Process variables
• Diag/Service
• Basic setup
• Detailed setup
• Review
A
B
C
D, E
• Basic setup
• Detailed setup
• Review
• Diag/Service
• Process Variables
C
D, E
■ DTM (HART 7)
Root Menu
• Device Configuration - Configure/Setup
• Diagnostic
• Process Variable
B
A
F0301-01.ai
HART 7
A
• Process variables
• Pres
• Pres %
• AO
• SP
• SP %
• Snsr temp
• Engr Disp
• Engr exp
• Engr Unit
• Device Variables
and Status HART 7
DTM
• Pres
• Pres Data Quality
• Pres Limit Status
• SP
• SP Data Quality
• SP Limit Status
• Snsr temp
• Temp Data Quality
• Temp Limit Status
• Pres %
• Percent Range Data Quality
• Percent Range Limit Status
• AO
• Loop Current Data Quality
• Loop Current Limit Status
: HART 7 only
DD
• PV
• PV Data Quality
• PV Limit Status
• SV
• SV Data Quality
• SV Limit Status
• TV
• TV Data Quality
• TV Limit Status
• % rnge
• % rnge Data Quality
• % rnge Limit Status
• Loop current
• Loop current Data Quality
• Loop current Limit Status
F0301-02.ai
IM 01C25T01-06EN
HART 7
EJX
B
• Diag/Service
3-2
<3. Parameter Setting>
• Test device (DD)
• Status
• Self test
• Master test
• Squawk HART 7
• Simulate HART 7
• Status (DTM)
• Loop test
• Self test
• Master test
• Squawk HART 7
• Simulate HART 7
• Test Auto Release
Time
• Loop Test (DD)
• Test (DTM)
• Calibration
• Re-range (DD)
• Status group 1
• Status group 2
• Status group 3
• Status group 4
• Status group 5
• Status group 6
• Status group 7
• Status group 8
• Status group 9
• Status group 10 HART 7
• Device status
HART 7
• Ext dev status HART 7
• Cfg chng count HART 7
• Reset Cfg chng flag HART 7
• Time Stamp HART 7
• Keypad input
• Apply values
• Keypad input (DTM)
• Analog output trim
• D/A trim
• Scaled D/A trim
• Clear D/A trim
• Pres sensor trim
• Pres Zero trim
• Pres trim
• P LTP
• P UTP
• Pres trim info.
• SP sensor trim
• Trim info.
• Diag Parameters
EJX
• Error log
• Test Auto Release
Time (DD)
: HART 7 only
: EJX Series only
• Static Pres trim
• SP LTP
• SP UTP
• SP trim info.
• Trim Who
• Trim Date
• Trim Loc
• Trim Desc
• LRV
• URV
• Unit
• LSL
• USL
• Min span
• P LTD
• P UTD
• Clear P snsr trim
• SP LTD
• SP UTD
• Clear SP snsr trim
See B1
(next page)
• Error log view
• Error log Clear
F0301-03.ai
IM 01C25T01-06EN
3-3
<3. Parameter Setting>
EJX
• Diag Mode
• Diag Applicable
• Diag Variables
• Diag Description
• Ref fDP Status
• Ref fDP
• Ref fSPl Status
• Ref fSPl
• Ref fSPh Status
• Ref fSPh
• Ref BlkF Status
• Ref BlkF
• Ref DP Avg Status
• Ref DP Avg
• Fluct Variables
• fDP Status
• fDP
• fSPl Status
• fSPl
• fSPh Status
• fSPh
• Status
• Diag Error
EJX
• Diag Option
• ILBD Parameters
• Configuration
• Diag Output
• Set Diag Mode
• Diag Period
• Diag Lim
• Lim fDPmax
• Lim fDPmin
• Lim fSPlmax
• Lim fSPlmin
• Lim fSPhmax
• Lim fSPhmin
• Lim BlkFmax
• Lim BlkFmin
• Lim DPAvgmax
• Lim DPAvgmin
• Diag Reference
• Diag Supp Count
• Diag Description
• Ref fDP
• Ref fSPl
• Ref fSPh
• Ref BlkF
• Ref DP Avg
• Diag Ref Lim
• Diag DPComp
• Ref Lim fDPmin
• Ref Lim fSPmin
• Ref Lim BlkFmax
• Status
• Snsr temp
• Amp temp
• Flg temp
• Configuration
• Flg Temp Coef
• Flg Temp Lim
• HT Parameters
• Ratio fDP Status
• Ratio fDP
• Ratio fSPl Status
• Ratio fSPl
• Ratio fSPh Status
• Ratio fSPh
• BlkF Status
• BlkF
• DP Avg Status
• DP Avg
• CRatio fDP Status
• CRatio fDP
• NRatio fDP Status
• NRatio fDP
• Diag Reference
B1
• Diag Parameters
: EJX Series only
• Flg Temp Hi Alert Val
• Flg Temp Lo Alert Val
• Diag Out Option
• Diag Fixed Out Val
F0301-04.ai
IM 01C25T01-06EN
C
• Basic setup
3-4
<3. Parameter Setting>
HART 7
: HART 7 only
• Tag
• Long tag
HART 7
• Unit
• Re-range
• Keypad input
• Apply values
• Device infomation
• Date
• Descriptor
• Message
• Write protect
• Model HART 7
• Xfer fnctn
• LRV
• URV
• Unit
• LSL
• USL
• Min span
• Pres Damp
• Low cut
• Low cut mode
• H/L Swap
• SP setup
• SP Range
• SP Unit
• SP Damp
• SP A/G Setup
• SP H/L Select
• Keypad input
• SP Apply values
• A/G Select
• Atm. Pres Value
• SP LRV
• SP URV
• SP Unit
• SP LSL
• SP USL
• SP Min span
F0301-05.ai
IM 01C25T01-06EN
D
HART 7
EJX
• Detailed setup
• Review
• Sensors
3-5
<3. Parameter Setting>
• Pressure sensor
• SP sensor
• Temp sensor
• Snsr temp
• Amp temp
• Temp Unit
• Pres
• Pres %
• Unit
• Pres sensor trim
• SP
• SP %
• SP Unit
• A/G Select
• SP H/L Select
• SP sensor trim
: HART 7 only
: EJX Series only
• Pres Zero trim
• Pres trim
• P LTP
• P UTP
• Pres trim info.
• P LTD
• P UTD
• Clear P snsr trim
• Static Pres trim
• SP LTP
• SP UTP
• SP trim info.
• SP LTD
• SP UTD
• Clear SP snsr trim
• SP LRV
• SP URV
• SP Unit
• SP LSL
• SP USL
• SP Min Span
• SP setup
• Signal condition
• Process variables
• Re-range
• Unit
• Xfer fnctn
• Pres Damp
• Low cut
• Low cut mode
• H/L Swap
• Bi-dir mode
• Quick resp
• T.Z. Cmp menu
• S.C. menu
• Output condition
• Pres
• Pres %
• SP
• Snsr temp
• Keypad input
• Apply values
• S.C.
• Num of points
• Point setting
• X Start
• Y Start
• X End
• Y End
• Process variables
• Analog output
• Loop test
• Loop current mode
HART 7
See D1
(next page)
• Display condition
• Device information
• Test Key
See E
• D/A trim
• Scaled D/A trim
• Clear D/A trim
• AO alm typ
• Channel flags HART 7
• Auto recover
• AO lower limit
• AO upper limit
• SP Range
• SP Unit
• SP Damp
• SP A/G Setup
• SP H/L Select
• Keypad input
• SP Apply values
• A/G Select
• Atm. Pres Value
• LRV
• URV
• Unit
• LSL
• USL
• Min span
• T.Z. Cmp mode
• Temp Zero
• Pres
• Pres %
• AO
• SP
• SP %
• Snsr temp
• Engr Disp
• Engr exp
• Engr Unit
• Digital Output
EJX
F0301-06.ai
IM 01C25T01-06EN
<3. Parameter Setting>
HART 5
D1
HART 7
• Poll addr
• Loop current mode
• Burst Message 1
HART 7
• Num req preams
• Num resp preams
• HART output
HART 7
• Burst Condition
HART 7
• Burst mode HART 5
• Burst option HART 5
• Process Alerts (DD)
• Pres Alert mode
• Config Pres Alerts
• SP Alert mode
• Config SP Alerts
• Temp Alert mode
• Config Temp Alerts
• DO Config
• Process Alerts
(DTM)
EJX
• Burst Message 2
• Burst Message 3
Same as above
Same as above
• Event Notification
• PV Update time
period (DD)
• SV Update time
period (DD)
• TV Update time
period (DD)
• Update time period
(DTM)
• SP update time
(DTM)
• Temp update time
(DTM)
• Event Notification
Control
• Event Mask
• Set Event
Notification Timing
• Event Notification
Retry Time
• Max Update Time
• Event Debounce
Interval
• Hi Alert Val
• Lo Alert Val
• LSL
• USL
• Temp Hi Alert Val
• Temp Lo Alert Val
• Digital Output
• DO Select
• DO Signal type
• DO Test
• Pres Alert
• Pres Alert mode
• Config Pres Alerts
• SP Alert
• SP Alert mode
• Config SP Alerts
• Temp Alert
• Temp Alert mode
• Config Temp Alerts
• DO Config
EJX
• Burst mode
• Burst Command
• Burst Device
Variables
• Set Burst Trigger
• Set Burst Period
• Burst Msg Trigger
Mode
• Burst Trigger Level
• Update Period
• Max Update Period
• Digital Output
• DO Select
• DO Signal type
• DO Test
• Knowledge (DD)
• Knowledge (DTM)
• SP Hi Alert Val
• SP Lo Alert Val
• SP LSL
• SP USL
• Hi Alert Val
• Lo Alert Val
• LSL
• USL
• SP Hi Alert Val
• SP Lo Alert Val
• SP LSL
• SP USL
EJX
3-6
: HART 5 only
: HART 7 only
: EJX Series only
• Burst Variable Code
(DD)
• Device Variable
Code (DTM)
• Device Status Mask
• Status group 1 Mask
to 10 Mask
• Ext dev status Mask
• Device Diagnostic
Status 0 Mask
• Device Diagnostic
Status 1 Mask
• AO saturated Mask
• AO fixed Mask
• Event Status
• Time First Unack
Event Triggered
• Acknowledge Event
Notificatoin
• Event Status
• Event Number
• Time First Unack
Event Triggered
• Latched Cfg chng
count
• Latched Device
Status
• Latched Status
group 1 to 10
• Latched Ext dev
status
• Latched Device
Diagnostic Status 0
• Latched Device
Diagnostic Status 1
• Latched AO
saturated
• Latched AO fixed
• Temp Hi Alert Val
• Temp Lo Alert Val
F0301-07.ai
IM 01C25T01-06EN
• Review
: HART 7 only
HART 7
E
• Detailed setup
3-7
<3. Parameter Setting>
• Sensors
• Signal condition
• Output condition
• Display condition
• Disp select
• P disp condition
• Disp Pres % fnctn
• Disp Pres % Reso
• Pres disp point
• SP disp condition
• SP disp point
• Engr disp range
• Engr LRV
• Engr URV
• Engr exp
• Engr Unit
• Engr point
• Set Engr Unit
• Modify Engr Unit
• Bar indicator
• Chg power on info
• Device information
• Disp Out1
• Disp Out2
• Disp Out3
• Disp Out4
• Field device info
• Test Key
• Tag
• Long tag HART 7
• Date
• Descriptor
• Message
• Model 1
• Model 2
• Model 3
• Write protect
• Wrt protect menu
• Ext SW
• Revision #’s
• Additional Info
• Option Password
• Sensor infomation
• Self test (DD)
• Isoltr matl
• Fill fluid
• Gasket matl
• Process Conn matl
• Drain vent matl
• Process Conn type
• RS isoltr matl
• Process Conn size
• Num of RS
• RS fill fluid
• RS type
• Write protect
• Enable wrt 10min
• New password
• Software seal
• Universal rev
• Fld dev rev
• Software rev
• Chg universal rev
• Style No.
• Serial No.
• Mftr Date
• Extra No.
• Final asmbly num
• Dev id
• Distributor
• Country HART 7
• Max dev vars
HART 7
• Device Profile
HART 7
F0301-08.ai
IM 01C25T01-06EN
<3. Parameter Setting>
3-8
3.1.2 For DTM (EJX series: HART 5)
Root Menu
• Process Variables
• Device Status
• Diag and Service
• Easy Setup
• Configuration
• Calibration
• Write Protect
P
Q
R
S
T
U
V
P
• Process Variables
• Pres %
• AO
• URV
• LRV
• Xfer fnctn
• Pres Damp
• Pres
• SP
• A/G Select
• Snsr temp
• Engr Disp
• Engr exp
• Engr Unit
• USL
• LSL
• P UTP
• P LTP
Q
• Device Status
• Process Variable
• Pres %
• Pres
• SP
• Snsr Temp
• Diagnostic List
• Device Status
• Hardware Failure
• Transducer Status
• Diag Status
• Configuration
F0301-21.ai
IM 01C25T01-06EN
3-9
<3. Parameter Setting>
R
• Diag and Service
• Service
• Loop test
• Master test
• DO Test
• Error log view
• Error log Clear
• Test Key
• Test Auto Release
Time
• Diag Description
• BlkF
• fDP
• fSPh
• fSPl
• DPAvg
• Ref BlkF
• Ref fDP
• Ref fSPh
• Ref fSPl
• Ref DPAvg
• CRatio fDP
• NRatio fDP
• Ratio fDP
• Ratio fSPh
• Ratio fSPl
• Cap Temp
• Amp Temp
• Flg Temp
• Impulse Line
Blockage Detection
• Diag Mode
• Diag Period
• Diag DPComp
• Diag Description
• Ref BlkF
• Ref fDP
• Ref fSPh
• Ref fSPl
• Ref DPAvg
• Alarm Notification
• Advanced Diag
Variables
• Advanced Diag
Configurations
• Threshold
• Heat Trace
• Diag Out Option
• Diag Fixed Out Val
• Advanced Diag
Alerts
• Diag Error
• Alarm Notification
• Threshold
• Flg Temp
Coefficient
• Tuning
• Flg Temp
• Diag Option
• Diag Suppress Count
• Sensitivity
• Fig Temp High Limit
• Fig Temp Low Limit
• Related to high side
alarm
• Related to both side
alarm
• Related to low side
alarm
• Related to Flg temp
alarm
S
• Easy Setup
• Tag
• USL
• LSL
• Unit
• URV
• LRV
• Xfer fnctn
• Pres Damp
• Low cut
• Low cut mode
F0301-22.ai
IM 01C25T01-06EN
3-10
<3. Parameter Setting>
T
• Configuration
• Pressure Sensor
• Static Pressure
Sensor
• Physical Information
• Process Input
• Analog Output
• Local Display
• Process Conn type
• Process Conn matl
• Process Conn size
• Gasket matl
• Isoltr matl
• Drain vent matl
• Fill fluid
• RS type
• RS isoltr matl
• RS fill fluid
• Num of RS
• Disp Out1
• Disp Out2
• Disp Out3
• Disp Out4
• Disp Pres % fnctn
• Disp Pres % Reso
• Pres disp point
• Engr URV
• Engr LRV
• Engr Unit
• Engr exp
• Engr point
• SP disp point
• Bar Indicator
• Chg power on info
• Signal Characterizer
Menu
• Process Alerts
• Device Information1
• Model
• Manufacturer
• Hardware rev
• Software rev
• Date
• Descriptor
• Message
• Final asmbly num
• Auto recover
• Ext SW
• Device Information2
• HART
• Tag
• Poll addr
• Dev id
• Universal rev
• Fld dev rev
• Chg universal rev
• Num req preams
• Physical signal
code
• Burst mode
• Burst option
• SP USL
• SP LSL
• SP Min Span
• SP Unit
• SP URV
• SP LRV
• SP Damp
• SP H/L Select
• A/G Select
• Atm. Pres Value
• Pres %
• AO
• Unit
• URV
• LRV
• Apply values
• Xfer fnetn
• Pres Damp
• Low cut
• Low cut mode
• AO alm typ
• AO upper limit
• AO lower limit
• Quick resp
• Bi-dir mode
• Pres Alert mode
• Hi Alert Val
• Lo Alert Val
• SP Alert mode
• SP Hi Alert Val
• SP Lo Alert Val
• Temp Alert mode
• Temp Hi Alert Val
• Temp Lo Alert Val
• Digital Output
• DO Select
• DO Signal type
• USL
• LSL
• Min span
• H/L Swap
• T.Z. Cmp mode
• Temp Zero
• Pres
• Unit
• Pres %
• SP
• SP Unit
• SP %
• Snsr temp
• Temp Unit
• S.C.
• Num of points
• X Start
• X End
• Y Start
• Y End
• X1
• X2
• X3
• X4
• X5
• X6
• X7
• X8
• X9
• Y1
• Y2
• Y3
• Y4
• Y5
• Y6
• Y7
• Y8
• Y9
• Model 1
• Model 2
• Model 3
• Style No.
• Serial No.
• Mftr Date
• Extra No.
F0301-23.ai
IM 01C25T01-06EN
<3. Parameter Setting>
3-11
U
• Calibration
• Trim Who
• Trim Date
• Trim Loc
• Trim Desc
• Pres Zero trim
• P UTP
• P LTP
• P UTD
• P LTD
• Pres trim
• Clear P snsr trim
• SP UTP
• SP LTP
• SP UTD
• SP LTD
• Static Pres trim
• Clear SP snsr trim
• D/A trim
• Scaled D/A trim
• Clear D/A trim
V
• Write Protect
• Write Protect
• Enter new password
F0301-24.ai
IM 01C25T01-06EN
3.2 Basic Setup
IMPORTANT
After setting and sending data with the HART
configuration tool, wait 30 seconds before
turning off the transmitter. If it is turned off
too soon, the settings will not be stored in the
transmitter.
Item
Descriptor
Up to 16 characters or numbers*1
Message
Up to 32 characters or numbers*1
Date
mm/dd/yyyy
- mm: month (2 digits)
- dd: days (2 digits)
- yyyy: years (4 digits)
If there are specified when ordering, the desired Tag
No. and device information are set and shipped.
Tag No. and device information can be checked as
follows.
*2: Item
Procedure
Tag
[Root Menu] → Basic setup → Tag
Long tag
[Root Menu] → Basic setup → Long
(HART 7 only) Tag
Descriptor
[Root Menu] → Basic setup → Device
information → Descriptor
Message
[Root Menu] → Basic setup → Device
information → Message
Date
[Root Menu] → Basic setup → Device
information → Date
• Procedure to call up the display using DTM
(EJX: HART 5)
Item
Descriptor
Message
Date
Procedure
Easy Setup → Tag
or Configuration → HART → Tag
Configuration → Device information 1
→ Descriptor
Configuration → Device information 1
→ Message
Configuration → Device information 1
→ Date
When the Tag No. and device information are
changed, input them based on the following
limitations.
Up to 8 characters or numbers*1
Long tag
Up to 32 characters or numbers*2
(HART 7 only)
*1: • Procedure to call up the display using DD
(HART 5/HART 7) and DTM (HART 7/EJA:
HART 5)
Limitations
Tag
3.2.1 Tag and Device Information
Tag
3-12
<3. Parameter Setting>
SP
The characters bounded by the thick line in the following
table can be used.
All characters in the following table can be used.
!
"
#
$
%
&
'
(
)
*
+
,
-
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
*: SP shows one-byte space
3.2.2 Unit
The unit parameter is set at the factory before
shipment if specified at the time of order. Follow the
procedure below to change the unit parameter.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
[Root Menu] → Basic setup →
Unit
DTM (EJX: HART 5)
Easy Setup → Unit or
Configuration → Analog Output
→ Unit
Note that the Yokogawa default setting for the
standard temperature is 4°C (39.2°F). For the units
of mmH2O, inH2O, and ftH2O, the pressure varies
according to the standard temperature definition.
Select the appropriate unit with @68degF when a
standard temperature of 20°C (68°F) is required.
Available pressure units are shown below.
inH2O@68degF
inHg
ftH2O@68degF
mmH2O@68degF
mmHg
psi
bar
mbar
g/cm2
kg/cm2
Pa
kPa
torr
atm
MPa
inH2O
mmH2O
ftH2O
hPa
IM 01C25T01-06EN
3.2.3 Range Change
The range values are factory-set as specified by
the customer. To change the range, follow the steps
below.
(1) Keypad input — LRV and URV
The measurement span is determined by the upper
and lower range values. In this method, the upper
and lower range values can be set independently,
and the span changes according to the range limit
values sent to the transmitter.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ LRV
→ URV
[Root Menu] → Basic setup →
Re-range → Keypad input
Easy Setup → or Configuration
→ Analog Output →
Lower range value
Upper range value
NOTE
The calibration range can be set as LRV > URV
under the following conditions, reversing the 4
to 20 mA output signal. When using the integral
indicator, change the user set scale values
accordingly.
Conditions:
LSL ≤ LRV ≤ USL
LSL ≤ URV ≤ USL
|URV – LRV| ≥ Min Span
LSL: Lower sensor limit of range setting
USL: Upper sensor limit of range setting
(2) Apply values — changing the ranges while
applying an actual Input
This feature allows the lower and upper range
values to be setup automatically with the actual
input applied. If the upper and lower range values
are set, URV and LRV are changed at the same
time.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
3-13
<3. Parameter Setting>
[Root Menu] → Basic setup →
Re-range → Apply values →
Configuration → Analog Output
→ Apply values →
The measurement span is determined by the upper
and lower range values. Changing the lower range
value causes the upper range value to change
automatically, keeping the span constant. If a
change in the lower range value causes the upper
range value to exceed the measuring limit of the
transmitter, an error message appears and the
transmitter holds the output signal right before the
error occurred. Enter the correct values within the
range of the sensor limits.
Note that changing the upper range value does
not cause the lower range value to change. Thus,
changing the upper range value also changes the
span.
3.2.4 Output Mode
The mode setting for the output signal and the
integral indicator can be performed independently.
The output mode for the output signal is set as
specified in the order when the instrument is
shipped. Follow the procedure below to change the
mode.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Xfer fnctn
[Root Menu] → Basic setup →
Easy Setup → or Configuration
→ Analog Output →
Select “Linear” or “Sq root”
3.2.5 Damping Time Constant Setup
The damping time constant is set as specified in
the order when the instrument is shipped. Follow
the procedure below to change the damping
time constant. The damping time constant for the
amplifier assembly can be set here. The damping
time constant for the entire transmitter is the sum
of the values for the amplifier assembly and the
capsule assembly.
Any number from 0.00 to 100.00 can be set for the
damping time constant. Note that setting the quick
response parameter ON enables you to set the time
constant between 0.00 and 0.49 seconds.
• Procedure to call up the Pres Damp display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Basic setup →
Pres Damp
Easy Setup → Pres Damp or
Configuration → Analog Output
→ Pres Damp
IM 01C25T01-06EN
3.2.6 Output Signal Low Cut Mode Setup
Low cut mode can be used to stabilize the output
signal near the zero point.
The low cut point can be set in a range from 0 to
20%, the direct ratio corresponding to the output
signal of 4 to 20 mA. (Hysteresis for the cut point:
±10% of the cut point)
Either “Linear” or “Zero” can be selected as the low
cut mode. Unless otherwise specified, the cut mode
is set to “Linear” at the factory.
The default value of Low cut is set according to the
combination of the Output mode (Xfer fnctn) and
Integral indicator display mode (Disp Pres % fnctn).
See below table.
Relationship of default value of Low cut and
Low cut point
Combination of
output mode and
display mode
Output Display
#
mode
mode
1) Linear
Linear
2) Sq Root Sq Root
3) Linear Sq Root
4) Sq Root Linear
Default
value of
Low cut
10%
10%
1%*
10%
Low cut
point for
the output
signal/
display
10% / 10%
10% / 10%
1% / 10%
10% / NA
*: It is applied for software revision 2.02 or later. For
previous software version, it is set in 10%.
In the case 3) above, Low cut point for the display is
square root of Low cut value.
(Example: Low cut value; 2%, Low cut point; 14%)
Note that when the output modes of the output
signal and the display are selected as “Sq root”
and “Linear” accordingly, the low cut function is not
available for the display value.
Example: Low cut at 20%
(%)
50
(%)
50
Output
→ Off
→ On
[Root Menu] → Detailed setup
→ Signal condition → Quick
resp →
Configuration → Analog Output
→ Quick resp →
Set from 0.50 to 100.00
Set from 0.00 to 100.00
Output
• Procedure to call up the Quick resp display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
3-14
<3. Parameter Setting>
20
0
Input
50
(%)
For low cut in linear mode
20
0
50
(%)
Input
For low cut in zero mode
F0302.ai
Figure 3.1
Low Cut Mode
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Low cut
→ Low cut mode
[Root Menu] → Basic setup →
Easy Setup → or Configuration
→ Analog Output →
Set from 0 to 20% of output
Select “Linear” or “Zero”
The low cut point has hysteresis so that the output
around the point is behaved as below figure.
<Example>
Output mode: Linear
Low cut mode: Zero
Low cut: 20.00%
Output
Low cut point
7.2mA
(20%)
4mA
Input
Setting range: 0 to 20%
2%
2%
Hysteresis
fixed at 10%
of the cut point
F0303.ai
3.2.7 Impulse Line Connection Orientation
Setup
This function reverses the impulse line orientation.
Follow the procedure below to assign the high
pressure impulse line connection to the L side of the
transmitter.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ H/L Swap
[Root Menu] → Basic setup →
Configuration → Pressure
Sensor →
Select “Normal” or “Reverse”
IM 01C25T01-06EN
<3. Parameter Setting>
3-15
3.2.8 Static Pressure Setup
(4) Selection of pressure side
The differential pressure transmitter can display the
static pressure also.
Either the high or low pressure side of capsule can
be selected to monitor the static pressure.
(1) Setting of the unit for static pressure
High pressure side is selected when the transmitter
is shipped.
Follow the procedure below to change the static
pressure unit.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ SP Unit
[Root Menu] → Basic setup →
SP setup →
Configuration → Process Input
(or Static Pressure Sensor) →
Select the unit for static
pressure (Refer to subsection
3.2.2 Unit)
(2) Setting of the measuring range for static
pressure
Follow the procedure below to change the lower
range value (LRV) and upper range value (URV).
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ SP LRV
→ SP URV
[Root Menu] → Basic setup
→ SP setup → SP Range →
Keypad input →
Configuration → Static Pressure
Sensor →
Set the lower range value (0 %)
of static pressure
Set the upper range value (100
%) of static pressure
(3) Selection of Gauge pressure and Absolute
pressure
Either the gauge pressure or absolute pressure can
be selected to display on the LCD display.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ SP H/L Select
3.3
[Root Menu] → Basic setup →
SP setup →
Configuration → Static Pressure
Sensor →
Select “High” or “Low”
Detailed Setup
3.3.1 Bi-directional Flow Measurement
(a) Bi-dir mode enables selection of 50% output at
an input of 0 mmH2O.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Bi-dir mode
[Root Menu] → Detailed setup
→ Signal condition →
Configuration → Analog output
→
Select “On” or “Off”
(b) Combining Bi-dir mode with Xfer fnctn
provides a square root output computed
independently for 0% to 50% output and for
50% to 100% output.
 Output mode “LINEAR”
20 mA (100% display)
Absolute pressure is selected when the transmitter
is shipped.
LRV
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ A/G Select
→ Atm. Pres Value
[Root Menu] → Basic setup →
SP setup → SP A/G Setup →
Configuration → Static Pressure
Sensor →
Select “Gauge” or “Absolute”
0.1013 MPa when the
transmitter is shipped
HRV
4 mA (−100% display)
 Output mode “SQUARE ROOT”
20 mA (100% display)
Low Cut
LRV
HRV
4 mA (−100% display)
F0304.ai
IM 01C25T01-06EN
3.3.2 Analog Output Signal Adjustable
Range
3.3.4 Integral Indicator Scale Setup
Output signal adjustable range at normal operating
condition are set as shown below at the factory
when the instrument is shipped, and output signal
are limited by these value.
Standard
Option code /C1
Option code /C2 and /C3
Lower limit
Upper limit
3.6 mA
21.6 mA
3.8 mA
20.5 mA
Output signal range can be changed between
3.6mA and 21.6mA to match it to the equipment on
the receiving side.
Lower value is set at AO lower limit and upper
value is set at AO upper limit respectively.
Follow the procedure below to change the upper
and lower values.
The following five displays are available for integral
indicators: input pressure, % of range, user set
scale, input static pressure*1, and % of static
pressure range*1. A cycle of up to four displays can
be shown by assigning variables to the parameters
at Disp select.
Available displays
Input pressure
(PRES)
→ AO lower limit
→ AO upper limit
Indicates values of input pressure
with the indication limits –99999 to
99999.
% of range
(PRES %)
456 kPa
Indicates input pressure in –2.5 to
110% range depending on the
set range (LRV and URV).
PRES %
[Root Menu] → Detailed setup
→ Output condition → Analog
output →
Configuration → Analog output
→
Set the lower value (mA)
Set the upper value (mA)
User set scale
(ENGR. PRES)
3.3.3 Integral Indicator Display Mode
The mode setting for the output signal and the
integral indicator can be performed independently.
The output mode for the integral indicator is set
as specified in the order when the instrument is
shipped. Follow the procedure below to change the
mode.
• Procedure to call up the display
[Root Menu] → Detailed setup
→ Display condition → P disp
condition →
Configuration → Local Display
→
→ Disp Pres % fnctn Select “Linear” or “Sq root”
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
Input static pressure
(SP)*1
45.6 %
Indicates values depending on the
engineering range (Engr LRV and
Engr URV) with the unit (Engr Unit).
Engr
Engr
Engr
Engr
Engr
Set the values as below.
Lower value < Upper value
If the instrument is equipped with an integral
indicator and the transfer function is sq root, “
displayed on the integral indicator.
Description
and related parameters
PRES
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
3-16
<3. Parameter Setting>
LRV
URV
exp
Unit
point
0.0
45.0
×100
m3/min
1
Indicates input static pressure with
the indication limits –99999 to 99999.
Reference pressure is factory-set in
absolute.
SP
4.000 MPa
% of static pressure range Indicates input static pressure in
(SP %)*1
–10 to 110% range depending on
the set range (SP LRV and SP
URV).
SP %
52.6 %
*1: Available for differential pressure transmitter.
F0305.ai
See (a.) through (d.) shown below for the setting
procedures.
” is
IM 01C25T01-06EN
a. Display Selection
At Disp select, select the variable that the
parameter Disp Out 1 will display on the integral
indicator.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Disp Out 1 to 4
[Root Menu] → Detailed setup
→ Display condition → Disp
select →
Configuration → Local Display
→
Select desired display from five
kinds of display shown above.
Set Disp Out 2, Disp Out 3 and Disp Out 4 in the
same way if necessary.
In addition to the above item, “Not used” is also
displayed as a selection item.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
→ Set Engr
Unit
→ Engr LRV
→ Engr URV
→ Engr exp
→ Engr point
kPa
MPa
mbar
bar
psi
psia
mmH2O
mmHg
mmHgA
mmAq
mmWG
Torr
inH2O
inHg
inHgA
Up to four displays can be displayed cyclically in the
order of the parameter number.
c. Display Resolution
User can change the position of decimal point
which is shown on the integral indicator.
• Procedure to call up the display for PV %
→ Disp Pres %
Reso
[Root Menu] → Detailed setup
→ Display condition → P disp
condition →
Configuration → Local Display
→
Select the decimal point position
of pressure
Normal: Display one digit below
the decimal point
High Resolution: Display two
digits below the decimal point
[Root Menu] → Detailed setup
→ Display condition →
Configuration → Local Display
→
(→ P disp condition) Select the decimal point position
→ Pres disp point
of differential pressure (0, 1, 2,
3 or 4)
(→ SP disp condition) Select the decimal point position
→ SP disp point
of static pressure (0, 1, 2, 3 or 4)
d. User Setting of Engineering Unit and Scale
[For DD (HART 5/7) and DTM (HART 7/EJA: HART
5)]
Engr disp range parameters allow the engineering
unit and scale to be displayed. At Set Engr Unit,
the following engineering units can be selected from
a list.
Select the engineering unit
Lower range value
Upper range value
Exponents for user scale display
Decimal point position for user scale
display (0, 1, 2, 3 or 4)
ftH2O
gf/cm2
kgf/cm2
kg/cm2G
kg/cm2A
atm
kg/h
t/h
m3/h
m3/min
l/h
l/min
kl/h
kl/min
Nl/h
Nl/min
Nm3/h
Nm3/min
ACFH
ACFM
SCFH
SCFM
GPH
GPM
m
mm
in
ft
kg/m3
g/cm3
At Modify Engr Unit parameter, user can set your
own unit also.
Up to eight alphanumeric characters, spaces or one
slashe (/) can be input at Modify Engr Unit; only
the first six are displayed on the integral indicator.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
→ Modify Engr
Unit
• Procedure to call up the display for Pres and SP
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Detailed setup →
Display condition → Engr disp range
Select the engineering unit from the list. Available
units are shown below
b. Cyclic Display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
3-17
<3. Parameter Setting>
[Root Menu] → Detailed setup →
Display condition → Engr disp range
→
Set your own unit
Note that following symbols are not available:
# % & < > . * : + - , ’ ( )
The integral indicator shows “-- -- -- -- -- --” when
these symbols or more than two slashes are
entered.
[For DTM (EJX:HART 5)]
User can input the desired unit at Engr Unit.
• Procedure to call up the display
DTM (HART 5)
→ Engr Unit
→ Engr LRV
→ Engr URV
→ Engr exp
→ Engr point
Configuration →Local Display →
Set the engineering unit
Lower range value
Upper range value
Exponents for user scale display
Decimal point position for user scale
display
Available characters and symbols for Engr Unit are
the same as for Modify Engr Unit shown above.
IM 01C25T01-06EN
3.3.5 Unit for Displayed Temperature
When the instrument is shipped, the temperature
units are set to “deg C” (Centigrade). Follow the
procedure below to change this setting.
When this parameter is set, it also changes the
temperature unit for Snsr temp at Process
variables and Amp temp at Temp sensor.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Temp Unit
3-18
<3. Parameter Setting>
[Root Menu] → Detailed setup
→ Sensors → Temp sensor →
Configuration → Process Input
→
Select the temperature unit
(deg C, deg F, Kelvin(K))
3.3.6 Sensor Trim
The transmitter is factory characterized. Factory
characterization is the process of comparing a
known pressure input with the output of each
transmitter sensor module over the entire pressure
and temperature operating range. During the
characterization process, this comparison
information is stored in the transmitter EEPROM. In
operation, the transmitter uses this factory-stored
curve to produce a process variable output (PV), in
engineering units, dependent on the pressure input.
The sensor trim procedure allows you to adjust
for local conditions, changing how the transmitter
calculates process variables. There are two ways
to trim the sensor: a zero trim and a full sensor trim.
A zero trim is a one-point adjustment typically used
to compensate for mounting position effects or
zero shifts caused by static pressure. A full sensor
trim is a two-point process, in which two accurate
end-point pressures are applied (equal to or greater
than the range values), and all output is linearized
between them.
(1) Zero Trim
a. Zeroing—Pres Zero trim
Pres Zero trim carries out the zero adjustment and
automatically sets the applied “0” input values to the
output value of “0”, keeping the span constant. Use
this setting when the LRV is known to be 0 mmH2O.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Diag/Service
→ Calibration → Pres Sensor
trim →
Calibration →
→ Pres Zero trim
Adjust the lower point
b. Level Adjustment—Auto, lower Pt
This zero adjustment calibrates the transmitter
output corresponding to the actual tank level. To
perform this adjustment, first use a glass gauge
or the like to determine the actual tank level, then
enter the correct data as shown below.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Diag/Service →
Calibration → Pres Sensor trim
→ Pres trim →
Calibration → Pres trim →
→ Auto, Lower Pt
Auto trim for 0% point
DPharp span: 0 to 25.00 kPa
Actual level: 13.50 kPa
Transmitter output: 13.83 kPa
25.00 kPa
Actual level
13.50 kPa
0.00 kPa
DPharp
F0306.ai
c. Using External Zero-adjustment Screw
This method permits zero adjustment without
the HART configuration tool. Use a slotted
screwdriver to turn the zero-adjustment screw.
See the hardware manual for details.
Note that the parameter of Ext SW must be
“Enabled” to perform this adjustment. See
section 3.3.8 for the setting procedure.
(2) Full Sensor Trim—Auto Trim and Manual
Trim Full sensor trim is carried out by performing Auto,
Lower Pt followed by Auto, Upper Pt.
Also, you can manually perform the trimming
procedure with Manual, Lower Pt and Manual,
Upper Pt.
IM 01C25T01-06EN
The full sensor trim is a two-point adjustment,
and the lower point adjustment should always be
performed before the upper point adjustment in
order to maintain the pitch between the zero and
100% points within the calibration range.
In the manual method, the reference pressure
should also be applied to the transmitter at both
the lower and upper points. Without the reference
pressure, Manual, Lower Pt and Manual, Upper
Pt may not represent the correct value for each
adjustment point.
a. Auto Sensor Trim
Applying reference pressure of 0% and 100% of the
measurement range to the transmitter, adjust the
lower and upper points automatically.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Auto, Lower Pt
→ Auto, Upper Pt
[Root Menu] → Diag/Service →
Calibration → Pres sensor trim
→ Pres trim →
Calibration → Pres trim →
Auto trim for 0% point
Auto trim for 100% point
b. Manual Sensor Trim
Using the example below, follow the steps to
perform the full sensor trim by manually. The Pres
LTD (Manual, Lower Pt) and Pres UTD (Manual,
Upper Pt) represent the previously adjusted values.
Example: For the range of 1000 to 3000 mmH2O
Pres LTD (Manual, Lower Pt) = −4.0 mmH2O
Pres UTD (Manual, Upper Pt) = −3.0 mmH2O
<1> Call up the Manual, Lower Pt.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Manual, Lower Pt
→ Manual, Upper Pt
[Root Menu] → Diag/Service →
Calibration → Pres sensor trim
→ Pres trim →
Calibration → Pres trim →
Manual trim for 0% point
Manual trim for 100% point
<2> S
uppose that a standard pressure of 1000
mmH2O is applied and the value of the “Pres
for trim” is 994.0. Correct for this output error
of 6 mmH2O by adding 6 mmH2O to Pres LTD
(Manual, Lower Pt).
3-19
<3. Parameter Setting>
<3> Enter the correction value of “2” to the Pres
LTD (Manual, Lower Pt).
<4> Call up the Pres UTD (Manual, Upper Pt).
<5> S
uppose that a standard pressure of 3000
mmH2O is applied and the value of the Pres for
trim is 3015.0. Firstly, obtain the slope error for
the span as follows;
Slope Error =
=
Applied Pressure Value−Value of Pres for Trim
Applied Pressure Value
× (URV−LRV)
3000−3015
× (3000−1000) = −10
3000
Then correct for this slope error of −10 by
adding −10 to Pres UTD (Manual, Upper Pt).
−3.0+(−10.0)=−13.0
<6> Enter the correction value of “−13” to the Pres
UTD (Manual, Upper Pt).
(3) Sensor Trim for Static Pressure
For the transmitter, full sensor trim of the static
pressure is performed in the same way as with the
differential pressure.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Auto, Lower Pt
→ Auto, Upper Pt
→ Manual, Lower Pt
→ Manual, Upper Pt
[Root Menu] → Diag/Service
→ Calibration → SP sensor
trim → Static Pres trim →
Calibration → Static Pres trim
→
Auto trim for 0% point
Auto trim for 100% point
Manual trim for 0% point
Manual trim for 100% point
(4) Reset Trim Adjistment to Factory Setting
The Clear P snsr trim and Clear SP snsr trim
commands can reset the trim adjustment to the
initial calibrated values that were set. The amount of
the adjustment performed with the external zeroadjustment screw is returned to the initial setting as
well.
−4.0+6.0=+2.0
IM 01C25T01-06EN
• Procedure to call up the display for pressure
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Diag/Service
→ Calibration → Pres sensor
trim → Pres trim info. → Clear P
snsr trim
Calibration → Clear P snsr trim
• Procedure to call up the display for static
pressure
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Diag/Service
→ Calibration → SP sensor trim
→ SP trim info. → Clear SP snsr
trim
Calibration → Clear SP snsr trim
3.3.7 Trim Analog Output
Fine current output adjustment is carried out with
D/A trim or Scaled D/A trim.
<Example>
Adjustment using a volt meter. (4mA → 1V, 20mA
→ 5V)
1) Select “Change”.
2) Enter the value read on the voltmeter when the output signal is 4mA.
In this case, enter the value of the voltage across a
250Ω resistor (1V).
3) Enter the value read on the meter when the output
signal is 20mA (5V).
4) Select “Proceed”.
5) Connect the voltmeter.
6) Output the 0% output signal and read the output
value.
7) Enter the reading of the voltmeter to the configuration
tool. (The output of the transmitter changes).
(1) D/A Trim
D/A trim is to be carried out if the calibration digital
ammeter does not exactly read 4.000 mA and
20.000 mA with an output signal of 0% and 100%.
8) Confirm the voltmeter reading is 1.000.
9) If the reading on the voltmeter is 1.000, select “Yes”.
[Root Menu] → Diag/Service →
Calibration
→ Analog output trim → D/A trim
Calibration → D/A trim
If the reading is not 1.000, select “No” and repeat
steps 6 and 7 until the voltmeter reads 1.000V.
• Procedure to call up the D/A trim display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
3-20
<3. Parameter Setting>
10) Output the 100% output signal and read the output
value.
11) Enter the reading of the voltmeter.
12) Confirm the voltmeter reading is 5.000.
(2) Scaled D/A Trim
13) If the reading of the voltmeter is 5.000, select “Yes”.
Scaled D/A trim is to be carried out if the output is
adjusted using a voltmeter or a meter whose scale
is 0 to 100%.
• Procedure to call up the Scaled D/A trim
display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
[Root Menu] → Diag/Service →
Calibration
→ Analog output trim →Scaled
D/A trim
Calibration → Scaled D/A trim
If the reading on the voltmeter is not 5.000, select
“No” and repeat steps 10 and 11 until the voltmeter
reads 5.000V.
3.3.8 External Switch Mode
Follow the procedure below to enable or inhibit zero
point adjustment by means of the zero-adjustment
screw on the transmitter.
This is set to “Enabled” when the instrument is
shipped.
To change the mode, follow the procedure below.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
Enabled
Disabled
[Root Menu] → Detailed setup
→ Device information → Field
device info → Ext SW
Configuration → Device
information1 → Ext SW
Enable the external zero point
adjustment
Disable the external zero point
adjustment
IM 01C25T01-06EN
<3. Parameter Setting>
3.3.9 CPU Failure Burnout Direction and
Hardware Write Protect
There are two slide switches on the CPU assembly
board. One sets the burnout direction at CPU
failure, and the other sets a write protection function
which disables parameter changes through
the use of a handheld terminal or some other
communication method.
CPU assembly
Burnout direction switch
BO H
L
WR E
D
Slide switch
Write protection switch
Burnout direction switch (BO)
Burnout Direction
Switch Position
H
Burnout Direction
L
H
HIGH
L
Write Protection
H
L
H
L
E
D
E
D
NO
(Write enabled)
3.3.10 Software Write Protection
The transmitter configured data is saved by using a
write protection function. The write protection status
is set to “Yes” when 8 alphanumeric characters are
entered in the New password field and transferred
to the transmitter.
When write protection is set to ”Yes,” the transmitter
does not accept parameter changes. When the
same eight alphanumeric string entered in the New
password field is also entered in the Enable wrt
10min field and transferred to the transmitter, it
will be possible to change transmitter parameters
during a 10 minute period.
To change the transmitter from the write protection
”Yes” status back to write protection ”No” status,
use Enable wrt 10min to first release the write
protection function and then enter eight spaces in
the New password field.
• Procedure to call up the display using DD
(HART 5/HART 7) and DTM (HART 7/EJA:
HART 5)
LOW
Hardware write protection switch (WR)
Write Protection
Switch Position
3-21
YES
(Write disabled)
F0307.ai
The parameter of AO alm typ parameter displays
the status of 4-20 mA DC output if a CPU failure
occurs. In case of a failure, communication is
disabled.
Standard specifications or with option code /C3
The burnout direction switch is set to “HIGH”. If a
failure occurs, the transmitter outputs a 110% or
higher signal.
With option code /C1 or /C2
The burnout direction switch is set to “LOW”. If a
failure occurs, a –5% or lower output is generated.
To confirm the burnout direction at the CPU failure,
follow the procedure below.
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
→ Write protect
→ Enable wrt 10
min
→ New password
[Root Menu] → Detailed setup
→ Device information → Field
device info → Wrt protect menu
→
Display current protect mode
(Yes: protected, No: not
protected)
Release the protect function for
10 min.
Set the new password or change
the password
• Procedure to call up the display using DTM
(EJX: HART 5)
DTM
Write Protect →
(EJX: HART 5)
→ Write Protect Display current protect mode
(Yes: protected, No: not protected)
→ Enter new
Enter the password here to enable
password
the protect function.
Enter eight spaces to disable the
protect function.
→ Enable write Enter the password here to release
the protect function for 10 min.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM
(EJX: HART 5)
High
Low
[Root Menu] → Detailed setup
→Output condition → Analog output
→ AO alm typ
Configuration → Analog output → AO
alm typ
Burnout direction is set to High
Burnout direction is set to Low
IM 01C25T01-06EN
<3. Parameter Setting>
3.3.11 Signal Characterizer
This function is used to compensate the output
for non-linear applications. The characterized
values are applied to the 4-20 mA output. For
the measured pressure, a maximum of nine
coordinates can be specified between 0-100%.
Perform the coordinate settings while the S.C. at
S.C. menu parameter is “Disabled”.
To apply the settings to the output, set the S.C.
parameter to “Enabled”.
• When the specified coordinates of x and y are
not incremental as the input increases.
• When the output mode of the output signal is
set as “Sq root”; at the same time, the low cut
mode is set to “Linear”.
INPUT
OUTPUT
Input pressure in %
Characterized value
100% X
F0308.ai
Follow the steps below to perform the signal
characterizer.
<1> Set the desired number of coordinates on the
line graph
• Procedure to call up the display
→ Num of points
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ S.C.
[Root Menu] → Detailed setup
→ Signal condition → S.C.
menu →
Configuration → Signal
Characterizer Menu →
Select “Enabled” or “Disabled”
The function is used to display the alarm codes
when the input pressure exceeds the specified
value within the calibration range. The same is
available for the input static pressure and the
capsule temperature on the pressure sensor.
Refer to table 4.5 Alarm Message Summary for the
specific alarm code to be generated.
(1) Alarm Setting
Select the process variable at Process Alert which
the alarm is set, then set the alert mode for that
value.
Y
100%
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
<3> Apply the settings
• Procedure to call up the display
3.3.12 Alarm
Note that the transmitter rejects the activation of the
function by AL. 60 with the following transmitter’s
status:
0%
3-22
[Root Menu] → Detailed setup
→ Signal condition → S.C.
menu →
Configuration → Signal
Characterizer Menu →
Set the number between 0 and
9
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
Selection of the
process variable for
alarm
Selection of alert
mode
[Root Menu] → Detailed setup
→ Output condition → Process
Alerts →
Configuration → Process Alerts
→
→ Pres Alert (DTM only) →
Pres Alert mode: Pressure
→ SP Alert (DTM only) →
SP Alert mode: Static pressure
→ Temp Alert (DTM only) →
Temp Alert mode: Capsule
temperature
Off: Disable the alert function
Hi. Al Detect: High side alert
detection
Lo. Al Detect: Low side alert
detection
Hi/Lo. Al Detect: High and Low
side alert detection
<2> Set the coordinates
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Point setting
[Root Menu] → Detailed setup
→ Signal condition → S.C.
menu →
Configuration → Signal
Characterizer Menu →
Set the coordinates (X-axis,
Y-axis)
IM 01C25T01-06EN
<3. Parameter Setting>
(2) Threshold Level Setting
Set the threshold of high and low alert value for
alarm generation.
• Procedure to call up the display
For DD (HART 5/7) and DTM (HART 7/EJA:
HART 5)
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
→ Hi Alert Val
→ Lo Alert Val
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
→ SP Hi Alert Val
→ SP Lo Alert Val
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
→ Temp Hi Alert Val
→ Temp Lo Alert Val
[Root Menu] → Detailed
setup→ Output condition →
Process Alerts → Temp Alert
(DTM only) → Config Temp
Alerts →
Set the threshold value of upper
side for capsule temperature
Set the threshold value of lower
side for capsule temperature
• Procedure to call up the display
For DTM ( EJX:HART 5)
DTM (EJX: HART 5)
→ Hi Alert Val
→ Lo Alert Val
→ SP Hi Alert Val
→ SP Lo Alert Val
→ Temp Hi Alert Val
→ Temp Lo Alert Val
NOTE
When option code /DG6 is specified, Diag can
be also assigned to Status. The Hi Alert Val or
Lo Alert Val for Diag is defined by the following
parameters.
[Root Menu] → Detailed
setup→ Output condition →
Process Alerts → Pres Alert
(DTM only) → Config Pres
Alerts →
Set the threshold value of upper
side for pressure
Set the threshold value of lower
side for pressure
[Root Menu] → Detailed
setup→ Output condition →
Process Alerts → SP Alert (DTM
only) → Config SP Alerts →
Set the threshold value of upper
side for static pressure
Set the threshold value of lower
side for static pressure
Configuration → Process Alerts
→
Set the threshold value of upper
side for pressure
Set the threshold value of lower
side for pressure
Set the threshold value of upper
side for static pressure
Set the threshold value of lower
side for static pressure
Set the threshold value of upper
side for capsule temperature
Set the threshold value of lower
side for capsule temperature
3-23
[Impulse Line Blockage Detection]
Limit meters to detect the blockage and
Condition error for ILBD operation is defined.
Refer to 4.2.2.1.
[Heat Trace Monitoring]
Flg temp Hi Alert Val and Flg temp Lo Alert
Val parameters are used as the upper and
lower threshold for Status output. Refer to
4.2.3.2.
3.3.13 Status Output (only for EJX series:
option code AL)
The transmitter has a contact output.
Select the type of output, status output, and set the
unit, value etc.
(1) Setting of status output
This feature is used for a transistor output (open
collector) of an on/off signal according to the
status of high and low alarm limits, which are
user-configurable values as shown in subsection
3.3.12 Alarm. The status output can be assigned
as any combination of the high or low limits of the
input pressure, input static pressure, or capsule
temperature.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7)
DTM (HART 5)
Display Item
Off
Pres
SP
Temp
Pres/SP
Pres/Temp
SP/Temp
Pres/SP/Temp
Diag Alarm
All
[Root Menu] → Detailed setup →
Output condition → Process Alerts
→ DO config → DO Select
Configuration → Process Alerts →
DO Select
Contents (Select a output variable
from the list below)
–
Differential pressure
Static pressure
Temperature
Pressure and static pressure
Pressure and temperature
Static pressure and temperature
Pressure, static pressure and
temperature
Alarm for advanced diagnostics
(Refer to subsection 4.2.2.5)
Alarm for pressure, static pressure,
temperature, and advanced
diagnostics
IM 01C25T01-06EN
NOTE
CAUTION
No status output signal has been defined for a
CPU failure or hardware error. Use a 4-20 mA
signal to indicate a transmitter’s failure.
Example: Status output operation of ON
WHEN AL. DETECT
 Status output for higher alert value
Output
(%)
5%* of hysteresis
Setting
value
On
Status output
On
Time (t)
Off
Setting
value
5%* of hysteresis
On
For transmitters with diaphragm seals, this function
is used to compensate the zero shift caused by the
ambient temperature effect on the capillary tubes.
(1) Temperature Compensation Mode Setup
When using this function, set T.Z. Cmp mode
to “On” to enable or “Off” to disable. To set to
“On”, follow the procedure below.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
Time (t)
Off
→ T.Z. Comp mode
*: 5% of setting span for differential pressure / pressure
F0309.ai
Figure 3.2 3.3.14 Capillary Fill Fluid Density
Compensation
Compensated output = output + K × Temp
Output
(%)
On
Whenever turning on the transmitter or detecting
the short interruption, check if contact output
correctly reflects the alarm status and test
the ON/OFF action of contact output by the
parameter DO test to confirm that the contact
output operates correctly.
The following equation indicates the relationship
between the calculated output value and the
compensating constant K (%/°C) with the measured
ambient temperature at the capsule module.
 Status output for lower alert value
Status output
3-24
<3. Parameter Setting>
Status Output
(2) Selecting of output signal
Status output can be selected for the contact
output.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Detailed setup →
DTM (HART 7) Output condition → Process Alerts →
DO config → DO Signal type
DTM (HART 5) Configuration → Process Alerts → DO
Signal type
ON WHEN AL. Output is “ON” when alert is detected
DETECT
OFF WHEN
Output is “OFF” when alert is detected
AL. DETECT
[Root Menu] → Detailed setup
→ Signal condition → T.Z.
Comp menu →
Configuration → Pressure
Sensor →
Select “On” or “Off”
Select “On” at the T.Z. Cmp mode display
(2) Zero Shift Compensation Setup
Obtain the K compensating value from the
equation (a) below, and enter the value to Temp
Zero.
– h×B
K= Span ×100.............. (a)
where,
B:Constant value of fill fluid (See Table A.)
Span: |URV – LRV|
h:Distance from high pressure side to low
pressure side (m)
EJX118A: Distance from high side of
diaphragm seal to low side of diaphragm
seal.
EJX438A: Distance from diaphragm seal
(high side) to position of transmitter (low
side).
IM 01C25T01-06EN
<3. Parameter Setting>
3.3.15 Test Output, Simulation, and Squawk
● EJX118A/EJA118E
L
h
NOTE
(+)
0
Transmitter
Fixed current output, DO Test, and Device
Variable Simulation Function continue for a given
holding time, then is released automatically.
Even if the HART configuration tool power
supply is turned off or the communication cable
is disconnected, the test output will continue for
that time.
The holding time can be selected from 10 min*,
30 min, 60 min, 3 hour, 6 hour or 12 hour.
*: Default value.
H
● EJX438A/EJA438E
Transmitter
L
h
(+)
H
0
Transmitter
(–)
L
• Procedure to call up the display
h
Note: When the transmitter is positioned lower than the
diaphragm seal part, the value of “h” must have a
negative sign (–).
F0310.ai
Example: Enter K value obtained from the equation (a).
A value haivng up to 3 decimal places may be
specified.
When h=+3 m, Fill fluid code A, span=15 kPa,
K=−(+3)×0.00745÷15×100=−0.149
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM (EJX: HART 5)
→ Temp Zero
[Root Menu] → Detailed setup
→ Signal condition → T.Z.
Comp menu →
Configuration → Pressure
Sensor →
Set the compensation value
Input “-0.149” to Temp Zero prameter.
Note 1: The function is performed using a built-in temperature
sensor in the transmitter body. The temperature
deviation between the transmitter body and capillaries
should be minimized to achieve optimal performance
of the function.
Note 2: When the span changes, reenter the newly obtained
value of K to Temp Zero.
Constant value [B]
Table A. Constant value [B] of fill fluid
Fill fluid
code
mmH2O
kgf/cm2
kPa
mBar
atm
inH2O
psi
mmHg
3-25
A, C
B
D
E
0.76
0.000076
0.00745
0.07453
0.000074
0.02992
0.00108
0.05592
0.87
0.000087
0.00853
0.08532
0.000084
0.03425
0.00124
0.06401
1.45
0.000145
0.01422
0.14220
0.000140
0.05709
0.00206
0.10669
0.75
0.000075
0.00736
0.07355
0.000073
0.02953
0.00167
0.05518
DD (HART 5/7)
DTM (HART 7/
EJA: HART 5)
DTM
(EJX: HART 5)
[Root Menu] → Diag/Service →
Test Auto Release Time
[Root Menu] → Diag/Service →
Test → Test Auto Release Time
Diag and Service → Service
→ Test Auto Release Time
(1) Fixed current output
This feature can be used to output a fixed current
for loop checks. The available range for test output
depend on the settings for the AO lower limit and
AO upper limit parameters, whose limit is from
3.6mA (-2.5%) to 21.6mA (110%).
Refer to the subsection 3.3.2 about the setting of
AO lower limit and AO upper limit.
While this function works, “TEST” is displayed on
the integral indicator.
 In the case of using DD (HART 5/HART 7)
and DTM (HART 7/EJA: HART 5)
Call up the test output parameter (Loop test) and
select the output signal.
• Procedure to call up the display
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
Display Item
4mA
20mA
Other
End
[Root Menu] → Diag/Service →
Test (DTM only) → Loop test →
Contents
Output a 4mA DC signal
Output a 20mA DC signal
Set a desired output signal value
Exit
Note 3: Select the unit of constant value of [B] from the actual
unit used for the transmitter in operation.
IM 01C25T01-06EN
 In the case of using DTM (EJX: HART 5)
Call up the test output parameter (Loop test) and
select either manual test or auto test, and set the
current value.
• Procedure of device variable simulation
Step 1 Call up the
parameter
Auto Test
Diag and Service → Service →
Loop test →
Contents
Set the current value or % value at
Test output value, then click the
Start button.
Set the interval and rate of change
of current output at Auto Test
Setting, then click the Start button.
Selection of
Device Variable
Select one parameter from
the list below
Off
PV
SV
TV
Percent Range
Loop Current
3
Setting of Value
Input the simulate value
4
Setting of Data
quality
Select one parameter from
the list below
Bad
Poor accuracy
Manual / Fixed
Good
5
Setting of Limit
status
Select one parameter from
the list below
Not limited
Low limited
High limited
Constant
(2) DO Test (only for EJX series)
This function performs the contact output test.
(option code: /AL)
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Detailed setup →
DTM (HART 7) Output condition → Process Alerts →
DO config → DO Test →
DTM (HART 5) Diag and Service → Service → DO
test →
Display Item
Contents
Off
Contact output: OFF
On
Contact output: ON
Exit
Output test is canceled
(3) Device Variable Simulation Function
(Effective only when setting to HART 7)
Using the simulation function, the output signal can
be confirmed by setting any value and status to the
selected device variable.
Call up the parameter and follow the message
shown.
After completing the step 5, the simulation starts.
Integral indicator shows output value and alarm
(AL.91) alternately.
[Root Menu] → Diag/
Service → Test (DTM)/Test
device (DD) → Simulate
2
• Procedure to call up the display
DTM
(EJX: HART 5)
Display Item
Manual Test
3-26
<3. Parameter Setting>
NOTE
• All the simulations for pressure, static
pressure, and capsule temperature are
reflected to the output. Accordingly, the loop
current, LCD display, and communication
output are directly corresponded to the
simulate value.
The alarm output is also available according
to the simulate value.
• Damping is applicable for pressure,
static pressure, and capsule temperature
simulation.
(4) Squawk (Effective only when setting to
HART 7)
This feature can be used to identify the
communicating transmitter by remotely causing
LCD to display the particular pattern as shown in
the Figure 3.3.
“SQUAWK” continues for approximately 15
seconds, then is released automatically.
Enter the larger number to “Change number of
squawks to make” in order to prolong the duration
of squawk indication.
IM 01C25T01-06EN
3-27
<3. Parameter Setting>
• Procedure to call up the Squawk display
(2) Shift to the Burst mode.
[Root Menu] → Diag/Service → Test (DTM)/Test device
(DD) → Squawk
To enable the Burst mode, select “On” at the Burst
mode parameter.
To release the Burst mode, call up the Burst
mode display and set it to “Off”.
This parameter is set to “Off” when the instrument is
shipped.
P
SP
T
F
• Procedure to call up the display
F0311.ai
Figure 3.3
LCD display for Squawk
3.3.16 Burst Mode
3.3.16.1In the case of using HART 5
When the Burst mode is enabled, the transmitter
continuously sends the stored data. The data is
sent approximately three times per second as a
digital signal when the transmitter is set in burst
mode. When data is being sent in burst mode,
other operations can be performed with the HART
configuration tool.
(1) Selection of the transmission data.
Call up the Burst option parameter and select the
data which is transferred.
• Procedure to call up the display
DD (HART 5)
DTM
(EJA: HART 5)
DTM
(EJX: HART 5)
Display Item
PV
%range/current
Process vars/
crnt
[Root Menu] → Detailed setup →
Output condition → HART output →
Burst option →
Configuration → HART → Burst
option →
Contents
Process variable assigned to PV
(Either of pressure, static pressure)
Output in % and mA
Output in mA and process variables
assigned to PV, SV and TV.
(Output in mA, pressure, static
pressure and capsule temperature)
DD (HART 5)
DTM
(EJA: HART 5)
DTM
(EJX: HART 5)
Display Item
Off
On
[Root Menu] → Detailed setup →
Output condition → HART output →
Burst mode
Configuration → HART → Burst
mode
Contents
Stop the burst mode
Start the burst mode
3.3.16.2In the case of using HART 7
When the Burst mode is enabled, the transmitter
continuously sends up to three data listed in Table
3.1.
Refer to the subsection 3.3.16.2.1 Burst Message
for details.
When the Burst mode is set to “Wired HART
Enabled”, transmitter continuously sends alarm
signal also.
Refer to subsection 3.3.16.2.2 Event Notification for
detail.
When changing the setting of Burst mode, set “Off”
to the Burst mode.
Default setting is “Off”.
3.3.16.2.1 Burst Message and Burst Mode
(1) Burst message
The transmitter can transmit three burst messages
at the maximum.
The parameters for Burst Message are as follows.
• Burst Command
• Update Period and Max Update Period
• Burst Msg Trigger Mode
IM 01C25T01-06EN
Table 3.1
<3. Parameter Setting>
Burst parameters
Command parameter
PV
(Pressure • Differential
Pressure)
% range/current
(Percent of range, Loop
current)
Process vars/current
(Loop current, Pressure
• Differential Pressure
• Static Pressure •
Temperature)
Process vars/% range/
current
Mapping by user
Self diagnosis information
*1: 3-28
Burst Msg Trigger
Mode
Cmd1:PV
Continuous
Window
Rising
Falling
On-change
Cmd2:% range/current
Continuous
Window
Rising
Falling
On-change
Cmd3:Dyn vars/current
Continuous
Window
Rising
Falling
On-change
Cmd9:Device vars w/status Continuous
Window
Rising
Falling
On-change
Cmd48:Read
Continuous
Additional Device Status
On-change
Burst Command
Burst Trigger
Source
--PV
Burst Trigger Units
--Depend on the
assigned variable to
PV
--% range
--%
--PV
--Depend on the
assigned variable to
PV
----Top of Burst
Depends on mapping
Device Variables
--All status
-----
Output the data with time and status.
IM 01C25T01-06EN
3-29
<3. Parameter Setting>
(2) Burst mode setting procedure
• Procedure to call up the display
DD (HART 7)
DTM (HART 7)
[Root Menu] → Detailed setup →
Output condition →HART output →
Burst Condition → Burst Message
1,2 or 3 → Burst Command
a. Burst Command
Burst Command
Send to transmitter
Cmd9
Burst
Command?
Cmd1, Cmd2,
Cmd3, Cmd48
Burst Variable Code (DD)
Device Variable Code (DTM)
b. Burst Variable Code
Send to transmitter
Update Period
Max Update Period
c. Update period and
Max Update Period
by “Set Burst Period”
Send to transmitter
d. Burst Msg Trigger Mode
by “Set Burst Trigger”
Burst Msg Trigger Mode
Window
Rising
Falling
On-change
Burst Msg
Trigger Mode?
Continuous
Burst Trigger Level
Send to transmitter
e. Burst Mode
Burst mode
Send to transmitter
F0312.ai
IM 01C25T01-06EN
<3. Parameter Setting>
a. Burst Command
• Procedure to call up the display
Select the transmission data at Burst Command
parameter.
DD (HART 7)
DTM (HART 7)
Burst Command
Cmd1: PV
Command parameter
PV (Pressure • Differential
Pressure)
Cmd2: % range/current % range/current (Percent of
range, Loop current)
Cmd3: Dyn vars/current Process vars/current
(Loop current, Pressure •
Differential Pressure • Static
Pressure • Temperature)
Cmd9: Device vars w/
Process vars/% range/current
status
Mapping by user
Cmd48: Read
Self diagnosis information
Additional Device
Status
b. Burst Variable Code/Device Variable Code
This parameter need to be set when Burst
Command is Cmd9:Device vars w/status (up to
eight items).
• Procedure to call up the display
DD (HART 7)
DTM (HART 7)
Display Item
PV
SV
TV
% rnge
Loop current
Not Used
[Root Menu] → Detailed setup
→Output condition →HART output
→ Burst condition → Burst Message
1,2 or 3 → Burst Device Variables
→ Burst Variable Code (DD)/Device
Variable Code (DTM) →
Contents
Select the pressure
Select the static pressure
Select the capsule temperature
Select the % output
Select the output current
–
c. Update period and Max Update Period
Set to Update Period and Max Update Period.
When the period that is earlier than the operation
period of each process value was set, it is set
automatically to become bigger than an operation
period of the transmitter.
For Update Period, set the value that is smaller
than Max Update Period.
→ Update Period
/ Max Update
Period
3-30
[Root Menu] → Detailed setup
→Output condition →HART
output → Burst condition → Burst
Message 1,2 or 3 → Set Burst
Period
0.5 s
1s
2s
4s
8s
16 s
32 s
1 min
5 min
10 min
15 min
30 min
45 min
60 min
d. Burst Msg Trigger Mode
Set the Burst Msg Trigger Mode from the
parameters shown below.
When Burst Msg Trigger Mode is Window, Rising
or Falling, set the Burst Trigger Level.
• Procedure to call up the display
DD (HART 7)
[Root Menu] → Detailed setup →
DTM (HART 7) Output condition →HART output →
Burst condition → Burst Message 1,2
or 3 → Set Burst Trigger →
Display Item
Contents
Continuous
Burst Message is transmitted
continuously.
Window
In “Window” mode, the Trigger Value
must be a positive number and is the
symmetric window around the last
communicated value.
Rising
In “Rising” mode, the Burst Message
must be published when the source
value exceeds the threshold
established by the trigger value.
Falling
In “Falling” mode, the Burst Message
must be published when the source
value fall below the threshold
established by the trigger value.
On-change
In “On-change” mode, the Burst
Message must be published when the
source value on change established
by the trigger value.
IM 01C25T01-06EN
<3. Parameter Setting>
e. Burst Mode
When the Burst mode is set to “Wired HART
Enabled”, the transmitter starts to send the data.
• Procedure to call up the display
DD (HART 7)
DTM (HART 7)
[Root Menu] → Detailed setup
→Output condition →HART
output → Burst condition → Burst
Message 1,2 or 3 → Burst mode
→ Wired HART Enabled
3.3.16.2.2 Event Notification
When a setting change and a change of the Selfdiagnostics occur, device detect it as an event and
can transmit an alarm signal continuously.
Up to four events that occurred can be stored.
When using this function, set to Burst mode as
“Wired HART Enabled”.
(1) Set Event Notification
• Procedure to call up the display
[Root Menu] → Detailed setup
→Output condition →HART
output → Burst Condition →
Event Notification →
→ Event Mask
Set the status to detect
→ Set Event Notification Timing
→ Event
Set the retry time when the event
Notification
occur.
Retry Time
→ Max Update
Set the retry time when the event
Time
does not occur.
→ Event
The setting of the minimum event
Debounce
duration
Interval
→ Event
Stop the event monitor: Off
Notification
Shift to the monitor state: Enable
Control
event notification on tokenpassing data link layer
DD (HART 7)
DTM (HART 7)
a) Event Mask
Set the status to detect in the Event Mask
parameter.
Device Status Mask
Status group 1 Mask to 10 Mask
Ext dev status Mask
Device Diagnostic Status 0 Mask
Device Diagnostic Status 1 Mask
AO saturated Mask
AO fixed Mask
When changing the configuration of the device,
Configuration Changed (0x40) Flag (refer to Table
4.7) of Device Status is set, and Cfg chng count
(refer to subsection 4.1.3 (5)) is also incremented.
Configuration changed flag detection can be
masked by the Device Status Mask, but it is
impossible to mask the Cfg chng count.
3-31
Therefore, the configuration changes to the device
are always detected as an event regardless of the
setting of the Device Status.
b) Event Notification Retry Time/ Max Update
Time/ Event Debounce Interval
Set to Event Notification Retry Time, Max Update
Time and Event Debounce Interval.
For Event Notification Retry Time, set the value
that is smaller than Max Update Time.
Event Notification
Retry Time
/Max Update Time
--0.5 s
1s
2s
4s
8s
16 s
32 s
1 min
5 min
10 min
15 min
30 min
45 min
60 min
Event Debounce Interval
Off
0.5 s
1s
2s
4s
8s
16 s
32 s
1 min
5 min
10 min
15 min
30 min
45 min
60 min
c) Event Notification Control
Select “Enable event notification on token-passing
data link layer” in the Event Notification Control
parameter to shift to the monitor state:
(2) Acknowledge Event Notification
The transmission of the event message stops when
event is approved.
• Procedure to call up the display
DD (HART 7)
DTM (HART 7)
→ Acknowledge
Event Notification
[Root Menu] → Detailed
setup →Output condition →
HART output → Burst condition
→ Event Notification →
Knowledge →
Acquisition of the event number
and approval.
a) Get Event Number
Confirm the latest event number.
Execute Acknowledge Event Notification
method.
1)Enter Event Number is set to “0”.
2)OK.
3)Set “Trans 0: Read Event Notificaiton” to
Select Transaction.
4)OK.
5)Confirm Event Number.
IM 01C25T01-06EN
b) Acknowledge Event Notification
Execute Acknowledge Event Notification
method.
1)Set to Enter Event Number is in confirmed
Event Number a)5.
2)OK.
3)Set “Trans 1: Send Acknowledge” to Select
Transaction.
4)OK.
5)Confirm Event Status is 0x00.
(3) Event Notification Record
• Procedure to call up the display
DD (HART 7)
DTM (HART 7)
→ Acknowledge
Event Notification
[Root Menu] → Detailed setup →
Output condition →HART output
→ Burst condition → Event
Notification → Knowledge →
Acquisition of the event number
and approval.
a) Get Event Number
Confirm the latest event number.
Execute Acknowledge Event Notification
method.
1)Enter Event Number is set to “0”.
2)OK.
3)Set “Trans 0: Read Event Notificaiton” to
Select Transaction.
4)OK.
5)Confirm Event Number.
b) Confirmation record of Event Notification
Confirm four events checked in a).
Execute Acknowledge Event Notification
method.
1)Enter the event number to Enter Event
Number which is confirmed in a)5.
2)OK.
3)Set “Trans 0: Read Event Notificaiton” to
Select Transaction.
4)OK.
5)Knowledge menu displays events record.
Ex.) When the confirmed event number is 123.
123
122
121
120
Event Number
3-32
<3. Parameter Setting>
Explanation
The latest event
An event before the once.
An event before the twice.
An event before three times.
3.3.17 Multidrop Mode
3.3.17.1In the case of using HART 5
“Multidropping” transmitters refer to the connection
of several transmitters to a single communication
transmission line. Up to 15 transmitters can be
connected when set in the multidrop mode. To
activate multidrop communication, the transmitter
address must be changed to a number from 1 to
15. This change deactivates the 4 to 20 mA analog
output, sending it to 4 mA. The alarm current is also
disabled.
Setting of Multidrop Mode
(1) Polling address
• Procedure to call up the display
DD (HART 5)
DTM
(EJA: HART 5)
DTM
(EJX: HART 5)
→ Poll addr
[Root Menu] → Detailed setup →
Output condition → HART output →
Configuration → HART →
Enter the number from 1 to 15
(2) Enabling the Multidrop Mode of
Configuration Tool
About the procedure to call up the Polling
display, please refer to the User’s Manual of each
configuration tool.
NOTE
When the same polling address is set for
two or more transmitters in multidrop mode,
communication with these transmitters is
disabled.
(3) Communication when set in multidrop
mode.
• The HART configuration tool searches for a
transmitter that is set in multidrop mode when
it is turned on. When the HART configuration
tool is connected to the transmitter, the polling
address and the tag will be displayed.
• Select the desired transmitter. After that, normal
communication to the selected transmitter is
possible. However, the communication speed
will be slow.
To release multidrop mode, call up the Poll addr
display and set the address to “0”.
IM 01C25T01-06EN
3.3.17.2In the case of using HART 7
“Multidropping” transmitters refer to the connection
of several transmitters to a single communication
transmission line. Up to 63 transmitters can be
connected when set in the multidrop mode. To
activate multidrop communication, the transmitter
address must be changed to a number from 1 to 63.
If it sets to multidrop mode, in order to transmit all
the data in digital one, it is necessary to change a
setup of the analog output signal of 4 to 20 mA.
Setting of Multidrop Mode
(1) Polling address
• Procedure to call up the display
[Root Menu] → Detailed setup
→Output condition →HART
output →
Enter the number from 1 to 63
DD (HART 7)
DTM (HART 7)
→ Poll addr
NOTE
When the same polling address is set for
two or more transmitters in multidrop mode,
communication with these transmitters is
disabled.
(2) Analog Output Signal Setting
Set Disabled to Loop current mode and fix
an analog output signal to 4mADC. It becomes
impossible in this case, to also use a burnout
output.
However, in the case of the application which
receives and operates an analog output signal, an
analog output signal can be used for one loop. In
this case, set Enabled to Loop current mode.
• Procedure to call up the display
DD (HART 7)
DTM (HART 7)
Enabled
Disabled
3-33
<3. Parameter Setting>
[Root Menu] → Detailed setup
→Output condition →Analog output
→ Loop current mode →
Loop current mode is enabled.
Loop current mode is disabled.
(3) Enabling the Multidrop Mode of
Configuration Tool
About the procedure to call up the Polling
display, please refer to the User’s Manual of each
configuration tool.
(4) Communication when set in multidrop
mode.
• The HART configuration tool searches for a
transmitter that is set in multidrop mode when
it is turned on. When the HART configuration
tool is connected to the transmitter, the polling
address and the tag will be displayed.
• Select the desired transmitter. After that, normal
communication to the selected transmitter is
possible. However, the communication speed
will be slow.
To release multidrop mode, call up the Poll addr
display and set the address to “0”.
Return Loop current mode to Enabled.
3.3.18 Switching HART Protocol Revision
When the output signal code is “-J”, HART protocol
revision of the transmitter can be selectable from 5
or 7.
The HART protocol revision is set and shipped as
specified in the order.
To change the HART protocol revision after
shipment, follow the procedure shown below.
IMPORTANT
When changing the protocol revision, confirm the
items below.
• Protocol revision supported by HART
configuration tool must be the same or
higher than new protocol revision of the
transmitter. (Refer to Table 2.1)
• Confirm that the DD or DTM which is suitable
to new protocol revision of transmitter is
installed in the configuration tool. (Refer to
Section 2.3 or 2.4)
1) Call up the parameter for protocol revision
change
• Procedure to call up the Chg universal rev
display.
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM
(EJX: HART 5)
[Root Menu] → Detailed setup →
Device information → Field device
info → Revision #’s → Chg universal
rev
Configuration → HART → Chg
universal rev
IM 01C25T01-06EN
2) Activate the “Chg universal rev” method
IMPORTANT
The message is displayed to separate the
transmitter from the automatic control loop.
Confirm that the transmitter is separated.
3) Input the new revision number
An input column for new protocol revision number is
displayed.
Input the new HART protocol revision number of “5”
for HART 5 or “7” for HART 7.
4) Applying the new protocol revision
a. Close the configuration tool
After completion of Chg universal rev
method, close the HART configuration tool.
3-34
<3. Parameter Setting>
b.Confirm the new HART protocol revision
number
Call up the Universal rev parameter, and confirm
that the new HART revision number is displayed.
• Procedure to call up the Universal rev.
parameter.
DD (HART 5/7)
DTM (HART 7
/EJA:HART 5)
DTM
(EJX: HART 5)
5
7
[Root Menu] → Detailed setup
→ Device information → Field
device info → Revision #’s →
Universal rev →
Configuration → HART →
Universal rev. →
HART protocol revision: 5
HART protocol revision: 7
NOTE
When using a FieldMate, close the main display
of FieldMate.
b.Restart the transmitter
Turn off the power to the transmitter, and turn
it on.
IMPORTANT
New protocol revision is applied only after having
performed restart of the transmitter.
NOTE
A new HART revision number is displayed on
the integral indicator for three (3) seconds after
restart the transmitter. (Refer to section 2.1)
5) Confirming the new protocol revision
a.Restart the HART configuration tool
NOTE
When execute the other parameter confirmation
or setting change, execute after restart the
configuration tool.
IM 01C25T01-06EN
4.
<4. Diagnostics>
4-1
Diagnostics
4.1 Self-Diagnostics
4.1.1 Identify Problems by Using the
HART Configuration Tool
The HART configuration tool can be used to run
self-diagnostics on a transmitter and check for
incorrect data settings.
(1) Using DD(HART 5/HART 7) and
DTM(HART 7/EJA: HART 5)
The Self test and Status commands are available
for self-diagnostics. When Self test is run, the
integral indicator shows an error code and alarm
message if the transmitter detects any illegal
parameter settings or functional faults. See Table
4.5 Alarm Message Summary for probable cause
and countermeasures.
• Procedure to call up the Self test display
[Root Menu] → Diag/Service →
Test (DTM)/Test device (DD) → Self test
If no error is detected, “Self test OK” is displayed on
the configuration tool.
If the specific diagnostic item is known for the
check, you can directly call up the item by using the
Status command.
The status is categorized from 1 to 9 for HART 5,
and from 1 to 10 for HART 7.
See Table 4.5 to determine the status group.
Show an example below to confirm the status of
Status group 1.
When an improper operation is performed, the error
message is displayed.
See Table 4.6 HART Configuration Tool Error
Message.
(2) Using DTM(EJX: HART 5)
The Device Status commands are used for selfdiagnostics. When Device Status is run, the
integral indicator shows an error code and alarm
message if the transmitter detects any illegal
parameter settings or functional faults. See Table
4.5 Alarm Message Summary for probable cause
and countermeasures.
• Procedure to call up the Device Status display
Device Status
If no error is detected, “Status: Normal” is displayed
on the configuration tool.
If the specific diagnostic item is known for the
check, you can directly call up the item by using the
Diagnostic List in the Device Status display.
The Diagnostic List is categorized to Device Status,
Hardware Failure, Transducer Status, Diag Status,
and Configuration.
See Table 4.5 Alarm Message Summary.
If no error is detected, color symbol which shows
Normal State is displayed on top of the error
message.
If color symbol which shows Error State is
displayed, there is an error and a countermeasure
for that error is necessary.
• Procedure to call up the Status display
[Root Menu] → Diag/Service → Test device (DD only)
→ Status → Status group 1
If no error is detected, “Off” is displayed on the
configuration tool.
If there is an error, “On” is displayed on the
configuration tool, and a countermeasure for that
error is necessary.
Example of display:
Illegal P LRV
Illegal P URV
Illegal P SPAN
P SPAN trim err
P ZERO trim err
On
Off
Off
Off
Off
The HART configuration tool diagnoses at each
communication.
The HART configuration tool diagnoses at each
communication.
When an improper operation is performed, the error
message is displayed.
See Table 4.6 HART Configuration Tool Error
Message.
IM 01C25T01-06EN
4-2
<4. Diagnostics>
4.1.2 Checking with Integral Indicator
NOTE
If an error is detected by running self-diagnostics,
an error number is displayed on the integral
indicator. If there is more than one error, the error
number changes at three-second intervals.
See table 4.3.1 regarding the alarm codes.
(3) Data quality and Limit status
The transmitter can handle PV (Pres), SV (SP),
TV (Snsr temp), % rnge (Percent Range), and
Loop current. Each variable contains data
quality and limit status for providing useful
status about the data value. The data quality
is normally “Good”. However, in the case of a
sensor failure or out of measurement range,
it turns to “Bad” or “Poor Accuracy”. The limit
status indicates whether the data value is
limited (i.e., not responding to the process).
When the limit status is “Constant”, the value
will not be changed. For detail, refer to Table 4.9
and 4.10.
• Procedure to call up the display using DD
(HART 7) and DTM (HART 7)
[Dynamic Variables]
F0401.ai
Figure 4.1
Integral Indicator
4.1.3 Status information available for
HART 7
Status added to HART 7 is explained below.
(1) Device Status
Device Status indicates the current operating
status of the device. (Refer to Table 4.7)
Table 4.10 indicates the relationship between
alarm and Device Status.
• Procedure to call up the display using DD
(HART 7) and DTM (HART 7)
DD (HART 7)
[Root Menu] → Diag/Service → Test
DTM (HART 7) device (DD only) → Status → Device
status
(2) Extended Device Status
Ext dev status contains commonly used
device information. (Refer to Table 4.8)
Table 4.10 indicates the relationship between
alarm and Extended Device Status.
• Procedure to call up the display using DD
(HART 7) and DTM (HART 7)
DD (HART 7)
[Root Menu] → Process variables
DTM (HART 7)
→ Device variables and Status →
→ PV (Pres)
Good, Poor Accuracy, Manual/
Data Quality
Fixed, or Bad is displayed.
→ PV (Pres) Limit Constant, Low Limit, High Limit, or
Status
Not Limited is displayed.
It is the same about the SV (SP) and TV (Temp), %
rnge (Percent Range), and Loop current
(4) Time Stamp
Time Stamp displays the date and the time
information which the transmitter maintains
from the time of the power on.
It is used as the additional information of the
process value and the event.
• Procedure to call up the display using DD
(HART 7) and DTM (HART 7)
DD (HART 7)
DTM (HART 7)
→ Current Date
→ Current Time
[Root Menu] → Diag/Service →
Test device (DD only) → Status →
Time Stamp
It shows the number of operating
days.
It shows the running time.
NOTE
Time Stamp is reset when powering on.
DD (HART 7)
[Root Menu] → Diag/Service → Test
DTM (HART 7) device (DD only) → Status → Ext dev
status
IM 01C25T01-06EN
(5) Configuration Change Counter
The Configuration Change Counter is
incremented once for every user action
that changes the device’s configuration or
calibration. This value is never reset or written
and maintained even if power is removed from
the device.
• Procedure to call up the display using DD
(HART 7) and DTM (HART 7)
DD (HART 7)
DTM (HART 7)
→ Cfg chng
count
4-3
<4. Diagnostics>
[Root Menu] → Diag/Service →
Test device (DD only) → Status →
The configuration change times
are counted. The counted value
cannot be reset.
(6) Reset Configuration Changed Flag
Configuration Changed Flag can be reset by
this method.
NOTE
Refer to Configuration Changed (0x40) in the
Table 4.7.
• Procedure to call up the display using DD
(HART 7) and DTM (HART 7)
DD (HART 7)
[Root Menu] → Diag/Service → Test
DTM (HART 7) device (DD only) → Status → Reset
Cfg Chng flag
4.2 Advanced Diagnostics
(Only for EJX series)
4.2.1 Multi-sensing Process Monitoring
Multi-sensing process monitoring function (option
code: /DG6) provides the advanced diagnostics
to detect the abnormal conditions in process
environment such as an impulse line etc. by using
the EJX multisensing technology and its unique
algorithm. There are following two functions.
 Impulse Line Blockage Detection (ILBD)
The fluctuation change of differential pressure and
static pressure is monitored by a silicone resonant
sensor and detects a potential blockage condition.
The differential pressure transmitter gives also a
result of which pressure-side was plugged.
 Heat Trace Monitoring
The two temperature sensors built in the transmitter
calculate the flange temperature, the change of
which enables to detect the heat trace breakage or
the abnormal temperature due to the failure.
4.2.2 Impulse Line Blockage Detection
(ILBD)
ILBD is carried out by using statistical analysis
based on the measured values of process
fluctuations that exist in a fluid. An alarm on the
transmitter LCD display or an analog alert is
generated if blockage reaches a certain level.
The transmitter provides the following results as
blockage detection.
(1) A Blocking and B Blocking
These are blockage detections based on
the fluctuation value change of differential
pressure/pressure. With a differential pressure
transmitter, each result indicates that both or
single side is plugged.
(2) L Side Blocking
It is a low-pressure side blockage detection
based on the change of BlkF or low-pressureside fluctuation value.
(3) H Side Blocking
It is a high-pressure side blockage detection
based on the change of BlkF or high-pressureside fluctuation value.
*: BlkF indicates blockage degree characterized
by a comparison of the high- and low-pressureside fluctuation values. For the details, refer to
Figure 4.2.2.
IMPORTANT
• The pressure fluctuation amplitude in fluids
must be sufficiently large for blockages to be
detected.
• If the pressure fluctuation amplitude is too
low for a reference value to be obtained,
blockages detection operation cannot be
performed with an alarm that the reference
value is invalid.
• The pressure fluctuation amplitude may
decrease due to other causes unrelated with
a blockage according to process condition. In
above case, a false alarm of an impulse line
blockage may be generated. Before taking
action in response to a blockage alarm,
consider the plant operating conditions.
IM 01C25T01-06EN
<4. Diagnostics>
4-4
 Notes for Pressure or Level
Measurement
With pressure or level measurement, the pressure
fluctuation amplitude may reduce especially for the
following cases.
 Pressure Measurement
• Operational pressure is near outside of
diagnostic range.
• Even though pressure is constant, the flow
decreases than that under normal condition.
• A source of pressure fluctuation (pump,
compressor, blower, etc.) is shut down. As
a result, the pressure fluctuation amplitude
decreases.
 Level Measurement
• A transmitter is used to measure tank level and
the flow of fluid into or out of the tank comes to
a stop.
• The agitator in the tank is shut down.
• A source of pressure variation (a compressor,
etc.) that controls the internal pressure of a
sealed (closed) tank is shut down.
Before taking action in response to a blockage
alarm, consider the plant operating conditions.
IM 01C25T01-06EN
4-5
<4. Diagnostics>
 Functional block diagram
The figure below shows the functional block diagram of ILBD.
Pres, Pres %
Engr Disp
SP, SP %
Snsr temp
Amp temp
EJX
Sensor
signals
Sensor
Process Value
calculation
Blockage alarm
Diag Output
Option
DO Config
Blockage alarm
Blockage degree
Add result of
blockage detection to status
Result of blockage detection
Execution of
ILBD
Alarm
Masking
Result of blockage detection
Blockage alarm
Output 4-20mA
AO
-------(6)
Contact Output
Digital Output
-------(7)
Ratio fDP
Ratio fSPl
Ratio fSPh
BlkF, fDP
fSPl, fSPh
Diag Applicable*1
-------(1)
Diag Error
-------(4)
Response Code
(Device Status)
Status group 8,9
-------(2)
-------(3)
Display on LCD
-------(5)
F0402.ai
Figure 4.2
Functional Block Diagram of ILBD
The following outputs are given for the ILBD results.
Table 4.1
#
List of Outputs for ILBD
OUTPUT
Parameter name
Ratio fDP
Remarks
Parameters based on the fluctuation value and blockage degree.
: Non-Compensation ]
[ Diag DPComp:
fDP
Ratio fDP =
Ref fDP
[ Diag DPComp:
: Compensation ]
Ratio fSPl
(1)
Ratio fSPh
BlkF
fDP
fSPI
fSPh
Diag Applicable*1
(2)
Response Code
Device Status
(3) Status group 8, 9
Ratio fSPl =
Ratio fDP =
fDP
Ref fDP
×
Ref DPAvg
DPAvg
fSPl
Ref fSPl
fSPh
Ref fSPh
Blockage degree characterized in comparison of high-pressure side and low-pressure
side pressure fluctuation value.
Average value of the sum of squares of differential pressure fluctuations.
Average value of the sum of squares of low-pressure side static pressure fluctuation.
Average value of the sum of squares of high-pressure side static pressure fluctuation.
After the reference value is obtained, the applicable blockage defection and the status of
abnormal fluctuation are displayed on this parameter.
Ratio fSPh =
When an impulse line blockage is detected, “More Status Avairable” is generated in
Response Code Device Status.
When an impulse line blockage is detected, the result of the blockage detection
(alarm status) is indicated.
(4) Diag Error
When an impulse line blockage is detected, the results of the blockage detection
(alarm status) is indicated.
(5) Display on LCD
(6) Analog Output
(7) Digital Output
When impulse line blockage is detected, an alarm status is displayed on LCD.
When impulse line blockage is detected, an alarm status is output on 4 to 20mA.
When impulse line blockage is detected, an alarm status is output on Status output.
F0403.ai
*1:
Available only for DD (HART 5/HART 7) and DTM (HART 7).
For DTM (HART 5), the color of icon on the Diag Error display changes with the status.
IM 01C25T01-06EN
<4. Diagnostics>
4-6
4.2.2.1 Blockage Detection
 Limit parameter
When the parameter based on pressure fluctuation
exceeds the preset value, EJX diagnoses an
impulse line as blockage and gives an alarm. The
threshold values are set to Limit parameter shown
in below table.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD Parameters →
Configuration → Diag Lim →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Impulse Line
Blockage Detection → Threshold
→ Sensitivity →
Table 4.2
Limit Parameter
#
Parameter
Threshold value
[1] Lim fDPmax
Threshold to detect “A
Blocking” by using Ratio fDP
[2] Lim fDPmin
Threshold to detect “B
Blocking” by using Ratio fDP
[3] Lim fSPlmax
Threshold to detect “Large
Fluct L” by using Ratio fSPl
[4] Lim fSPlmin
Threshold to detect “L Side
Blocking” by using Ratio fSPl
[5] Lim fSPhmax
Threshold to detect “Large
Fluct H” by using Ratio fSPh
[6] Lim fSPhmin
Threshold to detect “H Side
Blocking” by using Ratio fSPh
[7] Lim BlkFmax
Threshold to detect “H Side
Blocking” by using BlkF
[8] Lim BlkFmin
Threshold to detect “L Side
Blocking” by using BlkF
[9] Lim DPAvgmax Threshold to detect “ILDB over
range” by using DPAvg and to
detect “Invalid Ref xx” by using
Ref DPAvg
[10] Lim DPAvgmin
Threshold to detect “ILDB over
range” by using DPAvg and to
detect “Invalid Ref xx” by using
Ref DPAvg
Table 4.3 shows the default values at the factory
setting.
NOTE
• When ILBD is performed for the first time,
use the default value. If the pressure
fluctuation amplitude is low or a false alarm
is often generated after ILBD is performed,
change the values of Limit parameters
according to the procedure described in
subsection 4.2.2.10. Tuning
IM 01C25T01-06EN
Table 4.3
#
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
4-7
<4. Diagnostics>
Default Values of Limit Parameter
Parameter
Lim fDPmax
Lim fDPmin
Lim fSPlmax
Lim fSPlmin
Lim fSPhmax
Lim fSPhmin
Lim BlkFmax
Lim BlkFmin
Lim DPAvgmax
Note 2
Lim DPAvgmin
Note 2
Differential pressure
transmitter
Flange
Diaphragm
mounted sealed differential Absolute
differential
pressure/
pressure
pressure
pressure
transmitter
transmitter
transmitter
EJX210A
EJX118A
EJX310A
Gauge/
Absol ute
pressure
transmitter
Gauge
pressure
transmitter
EJX110A
EJX115A
EJX130A
EJX120A
3
0.3
5
0.5
5
0.5
0.6
-0.6
3
0.3
10000
0
10000
0
10
-10
10000
0.3
10000
0
10000
0
10
-10
10000
0.3
10000
0
10000
0
10
-10
10000
0.3
10000
0
10000
0
10
-10
10000
0.3
10000
0
10000
0
10
-10
EJX510A
EJX530A
EJX610A
EJX630A
10000
0.3
10000
0
10000
0
10
-10
1
1
1
1
1
1
1
0.05
0.2
-1
-1
0.05
0.05
0.05
Note 1
EJX438A
EJX430A
EJX440A
Note 1: The default values are set for level measurement. If EJX118A is applied to flow measurement, enter the same value to Limit
parameter [1] to [10] as those of EJX110A.
Note 2: It indicates the threshold value for “ILBD over range” (refer to 4.2.2.5).
 A/B Blocking Detection
 H/L Blocking Detection
“A Blocking” and “B Blocking” indicates the result
estimated from blockage degree based on the
difference of the high- and low-pressure-side
fluctuation values. Ratio fDP, SQRT (fDP / Ref
fDP) is used to detect A/B blocking. Ref fDP is the
average value of the sum of squares of differential
pressure fluctuations under normal condition.
EJX differential pressure transmitter enables
to detect both-, a high-, or low-pressure-side
blockage. The blockage degree characterized
by a comparison of high-pressure side and lowpressure-side fluctuation values, BlkF, is used to
detect it. The value changes within a range of –1
to +1. As BlkF approaches +1, the high-pressureside blockage progresses. On the other hand, if it
approaches –1, the low-pressure-side blockage
progresses.
NOTE
A single-side impulse line blockage may
generate “B blocking” under the condition where
the fluctuation amplitude is much different
between high- and low-pressure sides.
1
Threshold
0
Blockage Progress
-1
BlkF
As a high- or low-pressure-side blockage
progresses, fDP increases. Therefore, “A Blocking”
with a differential pressure transmitter indicates
that a single-side impulse line is plugged for a
differential pressure transmitter. As the both-side
blockages progress simultaneously, fDP decreases.
Therefore, “B Blocking” with a differential pressure
transmitter indicates that both-side impulse lines
are plugged.
1
BlkF
As the value of Ratio fDP exceeds the value of
Lim fDPmax, EJX gives basically an alarm of “A
Blocking”. On the other hand, if this value is below
the value of Lim fDPmin, EJX gives an alarm of “B
Blocking.
0
-1
Blockage detection for
high-pressure side
Blockage Progress
Threshold
Blockage detection for
low-pressure side
F0404.ai
Figure 4.3
Relation between Blockage Progress
and BlkF
The each threshold value to detect the high- or lowpressure-side blockage is set to Lim BlkFmax or
Lim BlkFmin.
IM 01C25T01-06EN
 L Side Blocking Detection
BlkF is preferentially used to "L Side Blocking"
detection. If BlkF cannot be used, Ratio fSPl,
SQRT (fSPl / Ref fSPl) is used to "L Side Blocking"
detection. Ref fSPl is the average value of the sum
of squares of low-pressure-side static pressure
fluctuations under normal condition.
As the value of Ratio fSPl is below the value of Lim
fSPlmin, EJX gives an alarm of "L Side Blocking".
On the other hand, if this value exceeds the value of
Lim fSPlmax, EJX gives an alarm of “Large Fluct
L”.
 H Side Blocking Detection
BlkF is preferentially used to "H Side Blocking"
detection. If BlkF cannot be used, Ratio fSPh,
SQRT (fSPh / Ref fSPh) is used to "H Side
Blocking" detection. Ref fSPh is the average value
of the sum of squares of high-pressure-side static
pressure fluctuations under normal condition.
As the value of Ratio fSPh is below the value
of Lim fSPhmin, EJX gives an alarm of "H Side
Blocking".
<4. Diagnostics>
4-8
4.2.2.2 Combination of Reference Result
and Blockage Detection
 Diag Applicable
The transmitter can detect four modes of impulse
line blockage: both-sides, high-pressure side, lowpressure side, and/or single-side and abnormal
fluctuation when all the reference values are
properly measured. However, the detectable alarm
mode combination is limited when some of the
reference values are invalid. Available Blockage
Detection are shown in the below figure.
NOTE
• Ref fDP must be larger than the specified
level shown in Table 4.4 (refer to subsection
4.2.2.6). No blockage can be detected when
Ref fDP is not large enough.
• The plausibility of blockage detection needs
to be confirmed by blockage simulation test.
The simulation test can be performed by
the appropriate manifold operation (refer to
subsection 4.2.2.8).
On the other hand, if this value exceeds the value of
Lim fSPhmax, EJX gives an alarm of “Large Fluct
H”.
 Large Fluctuation Detection
When a pump or compressor starts, the large
fluctuation is generated as process condition
changes rapidly. This phenomenon affects process
fluctuation measurement; so correct blockage
detection is not performed.
If “Large Fluct L” or “Large Fluct H” is detected,
consider whether a blockage result is correct.
The threshold values to detect large fluctuation are
set to Lim fSPlmax and Lim fSPhmax.
Since these values are enough to detect large
fluctuation, it is not almost necessary to change
them.
IM 01C25T01-06EN
4-9
<4. Diagnostics>
[Differential pressure measurement]
Fluctuation Parameters
Ref fDP:
OK
Ref fSPI:
OK
Ref fSPh:
OK
Ref BlkF:
OK
Ref fDP:
OK
Ref fSPI:
OK
Ref fSPh:
OK
Ref BlkF:
NG
Ref fDP:
OK
Ref fSPI:
NG
Ref fSPh:
OK
Ref BlkF:
NG
Ref fDP:
OK
Ref fSPI:
NG
Ref fSPh:
NG
Ref BlkF:
NG
Simulation Test
Available Blockage Detection
• B Blocking detection
(by using Ratio fDP)
• L Side Blocking detection
(by using Ratio fSPI)
• H Side Blocking detection
(by using Ratio fSPh)
• H/L Side Blocking detection
(by using BlkF)
• Test for low-pressure side
• Test for high-pressure side
• Test for both-pressure sides
• A/B Blocking detection
(by using Ratio fDP)
• L Side Blocking detection
(by using Ratio fSPl)
• H Side Blocking detection
(by using Ratio fSPh)
• Test for low-pressure side
• Test for high-pressure side
• Test for both-pressure sides
• A Blocking detection
(by using Ratio fDP)
• H Side Blocking detection
(by using Ratio fSPh)
• Test for high-pressure side
• B Blocking detection
(by using Ratio fDP)
• Test for both-pressure sides
[Gauge/absolute pressure and level measurement]
Fluctuation Parameters
Ref fDP:
OK
Simulation Test
Available Blockage Detection
• B Blocking detection
(by using Ratio fDP)
• Test for high-pressure side
F0405.ai
4.2.2.3 Operation Parameters
 Diag Mode
Diag Mode gives the directive for the ILBD
operation. There are following three modes.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD Parameters →
Configuration → Set Diag Mode →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Impulse Line
Blockage Detection → Diag Mode →
Diag Mode
Mode
Stop
Function
The blockage detection operation is
stopped.
Calculation The blockage detection operation is
performed.
Alarms are generated along with the
result.
Reference Reference values for the blockage
detection are obtained and updated to the
latest. After sampling reference values,
this mode changes to "Calculation".
When the blockage detection operation is
performed, set “Calculation” to Diag Mode. “Stop”
must be set when you change a threshold value or
set an alarm. “Reference” is set in order to obtain
the reference fluctuation values under the normal
configuration.
IM 01C25T01-06EN
NOTE
When setting ILBD parameters in the transmitter
via “Online Parameter” of the DTM (HART 5)
menu, Diag Mode automatically changes to 0
(Stop). After the setting, Diag Mode automatically
returns to the original value.
4-10
<4. Diagnostics>
When the value exceeds consecutively the
threshold value three times, an alarm is generated
(see part ‘B’ in Figure 4.4).
Diag Supp Count (Number of times: 3)
An alarm is generated.
A
B
B
B
NOTE
When setting ILBD parameters in the transmitter
via “Download to device” of the DTM (HART 5)
menu, Diag Mode automatically changes to 0
(Stop).
Upper Threshold
(Ex.Lim fDPmax)
Diag Period
Time
 Diag Period
Diag Period
The values such as Ratio fDP and BlkF are
averaged based on several hundreds of pressure
fluctuation values in constant time. Diag Period
defines the sampling time is. The default value at
the shipment is set to 180 sec.
Lower Threshold
(Ex.Lim fDPmin)
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD Parameters →
Configuration → Diag Period →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Impulse Line
Blockage Detection → Diag Period →
For the information on how to change the sampling
period, refer to subsection 4.2.2.10.
 Diag Supp Count
When the value as Ratio fDP or BlkF exceeds
the threshold value for several times in a row,
it is estimated that the impulse line is plugged.
Diag Supp Count defines the number of times to
estimate blockage detection.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD Parameters →
Configuration → Diag Supp Count →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Impulse Line
Blockage Detection → Threshold →
Diag Suppress Count →
A
A
A
B
An alarm is generated.
Diag Supp Count (Number of times: 3)
Time
F0406.ai
Figure 4.4
Relationship of Diag Supp Count and
Alarm
The number of detection to give an alarm is set for
each blockage detection function. The default value
at the shipment is set to three times.
If fluctuating around the threshold value, an alarm
may be often generated. In this case, change the
threshold value (Limit parameter) or the sampling
time (Diag Period) to enhance the accuracy of the
blockage detection. Refer to subsection 4.2.2.10.
If Diag Supp Count is set to three times, an
alarm is not generated at part ‘A’ in Figure 4.4.
Because the first and second values only exceeded
consecutively the threshold.
IM 01C25T01-06EN
4-11
<4. Diagnostics>
4.2.2.4 Operating Procedure
If an alarm is often generated or the process
condition changed in the ILBD operation, do
tuning to change the alarm setting, or to reset the
reference values.
The basic flow of the ILBD operation is as follows.
1)Initial setting
2)Condition check
3)Start up
4)Perform the ILBD algorithm.
Fill out the information to the checklist, at the
process shown in below figure.
(Refer to the Appendix 1. ILBD Check List)
Items on
Check sheet
1-1) Alert Setting
• Enable an alert to be generated by
Diag Out Option parameter.
1, 2
Refer to subsection 4.2.2.5
1) Initial Setting
1-2) Alarm Masking
• Select the alarm status to display on
LCD or to give an alert by Diag
Option parameter.
7
Refer to subsection 4.2.2.5
2-1) Check Stability of pressure
• Check the stability of Pres value.
3
2) Condition
Check
4
Refer to subsection 4.2.2.6
2-2) Check Fluctuation Values
• Check whether the fluctuation values
are available for ILBD.
Refer to subsection 4.2.2.6
3-1) Obtain Reference Values
• Obtain a reference fluctuation value of
differential pressure/pressure and
static pressure under normal condition.
5, 6
Refer to subsection 4.2.2.7
3) Start up
10
3-2)
Check Detection
Capability
• Simulate the blockage detection
operation with a three-valve
manifold or stop valve.
NG
Tuning
• Change the threshold value by
Limit parameter.
• Change the sampling time by
Diag Period parameter.
Refer to subsection 4.2.2.8
Refer to
subsection 4.2.2.10
OK
4) Perform ILBD algorithm
Spurious alarm detection.
Refer to
subsection 4.2.2.9
Reset Reference Values
• Reset a reference fluctuation
value of differential
Process condition is
pressure/pressure according to
changed by a
process condition.
comparison of the
condition when the
reference values were
obtained.
Blockage Detection
Alarm is generated.
Figure 4.5
Refer to subsection 4.2.2.11
F0407.ai
Flow Chart of ILBD Operation
IM 01C25T01-06EN
4.2.2.5 Alarm and Alert Setting
The abnormal results as the blockage detection and
high/low flange temperature (heat trace monitoring)
are given through an analog alert or the LCD
display of alarm status. Before performing the ILBD
operation, it is necessary to set the alarm and alert
according to the following procedure.
Storage of Abnormal results
(Diag Error)
Alarm Masking
(Diag Option)
Outside Diagnosis Range/
Invalid Ref xx
Masking
Alarm on
Analog Output
Alarm on
Status Output
Alarm Display
on LCD
Device Status
Field Device More Status Available
Additional Device Status
(Status group 8 and 9)
F0408.ai
Figure 4.6
4-12
<4. Diagnostics>
Alarm and Alert Setting
 Alarm Status
When the algorithm of ILBD and Heat trace
monitoring detect the abnormality, the result is
stored in Diag Error. The alarm status based on the
detected abnormality is displayed to Diag Error.
(Displayed to Impulse Line Blockage Detection
and Heat Trace for DTM(HART 5))
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → Diag Error →
DTM (HART 5) Diag and Service → Advanced Diag
Alerts → Diag Error
DD
Bit (HART 5/HART 7) DTM (HART 5)
DTM (HART 7)
Not used
0 Not used
Not used
1 Not used
A Blocking
2 A Blocking
Large Fluctuation
3 Large Fluct L
of Low Side
Large Fluctuation
4 Large Fluct H
of High Side
Low Side Blocking
5 L Side Blocking
High Side
6 H Side Blocking
Blocking
B Blocking
7 B Blocking
Invalid Ref BlkF
8 Invalid Ref F
Invalid Ref fSPh
9 Invalid Ref SPH
Invalid Ref fSPl
10 Invalid Ref SPL
Invalid
Ref
DP
Invalid
Ref fDP
11
Outside Diagnosis
12 ILBD over range
Range
Flg Temp Low
13 FT low alarm
Alarm
Flg
Temp High
14 FT high alarm
Alarm
15 Not used
Not used
Category
ILBD
Heat trace
monitoring
Note: FT indicates the flange temperature.
 ILBD over range (Outside Diagnosis
Range)
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD Parameters →
Configuration → Diag Lim →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Impulse Line
Blockage Detection → Threshold →
1) Lim DPAvgmax
Lim DPAvgmax is the upper limit of the
diagnostic capability range. The limit value can
be changed when Diag Mode is “Stop”.
DPAvg indicates the ratio of the average of
differential pressure to the EJX maximum span
regarded as 1. When DPAvg exceeds this
limit, “ILBD over range” is generated so that the
blockage detection becomes impossible.
2) Lim DPAvgmin
Lim DPAvgmin is the lower limit of the
diagnostic capability range. The limit value can
be changed when Diag Mode is “Stop”.
When DPAvg is below this limit, “ILBD over
range” is generated so that the blockage
detection becomes impossible.
IM 01C25T01-06EN
<Example>
When the level range that can be measured by the
transmitter with 100 kPa span is –80 to 80 kPa, the
limits are set as follows.
• Lim DPAvgmax: 0.80
• Lim DPAvgmax: –0.80
1.000
ILBD over range
0.80
Detectable
DD
(HART 5/HART 7)
DTM (HART 7)
A Blocking
Large Fluct L
Large Fluct H
L Side Blocking
H Side Blocking
B Blocking
Invalid Ref DP
DTM (HART 5)
A Blocking
Large Fluctuation of Low Side
Large Fluctuation of High Side
Low Side Blocking
High Side Blocking
B Blocking
Invalid Ref fDP
To Link the alarm to an analog alert and LCD
display, follow the procedure below.
range
0.000
DPAvg
-0.80
-1.000
4-13
<4. Diagnostics>
1) Set “Stop” to Diag Mode.
2) Check each checkbox of the alarm, which is
selectable from bit 2 to 14.
Note: Set to “Calculation” after setting the parameter.
ILBD over range
F0409.ai
 Alert Setting
 Invalid Ref F, SPH, SPL, or DP
 Diag Out Option
This alarm indicates that the reference value under
normal condition is invalid. If Ref F is invalid, the
blockage detection excluding BlkF is carried out.
If blockage detection function based on BlkF is
required, obtain the reference value again.
When an alert regarding the impulse line blockage
or high/low flange temperature is generated, the
output value of 4-20 mA analog signal can be
changed.
Also when Ref DPAvg is below Lim DPAvgmin
or exceeds Lim DPAvgmax, all reference value
becomes invalid so that “Invalid Ref DP”, “Invalid
Ref SPL”, “Invalid Ref SPH”, and “Invalid Ref F” are
generated.
 Alarm Masking
 Diag Option
The alarms linked to an analog alert and LCD
display are selected by Diag Option.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → Diag Option →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Impulse Line
Blockage Detection → Diag Option →
The bit of Diag Option is corresponding to that
of Diag Error. The following alarms are set at
the factory setting, which is corresponding to
hexadecimal 0x08FC.
Mode
Function
Keeping PV measurement. The alert is not
Off
reflected to 4-20 mA analog signal.
The analog signal is shifted to the value of
AO upper limit or AO lower limit when an
Burnout alert is generated.
The shifted direction follows Burnout switch
setting.
The analog signal is hold to the specific
Fall back value, Diag Fixed Out Val, when an alert is
generated.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → Diag Output → Diag
Out Option →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Diag Out Option →
 Diag Fixed Out Val
This parameter is used when “Fall back” is selected
to Diag Output Option.
When an alert is generated, the 4-20 mA analog
signal is held on the value specified by this
parameter.
The value can be entered within 3.6 to 21.6 mA.
IM 01C25T01-06EN
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → Diag Output → Diag
Fixed Out Val →
DTM (HART 5) Diag and Service → Advanced Diag
Configurations → Diag Fixed Out Val
→
 Status Output for Advanced diagnostic
The output of the abnormal results are applicable
for a transistor output (open collector) of an on/off
signal according to the status of high and low alarm
limits, which are values set to Limit parameters as
shown in subsection 4.2.2.1. About the Flg Temp
Hi Alert Val, or Flg Temp Lo Alert Val for Heat
trace monitoring, refer to subsection 4.2.3.2.
 DO Select
If the advanced diagnostic function is installed, the
following modes can be also assigned to the status
output in addition to Pres, SP and Temp.
Mode
Function
The status regarding advanced diagnostic
Diag Alarm
masked by Diag Option is output.
All
status of Press, SP, Temp and advanced
All
diagnostic are output.
 Alarm Display on LCD
If the ILBD algorithm detects the abnormality, the
content of the detected result is displayed with
“AL.88” or “AL.89” on the LCD. “AL.88” indicates
that condition is not applicable for the abnormality
detection and “AL.89” indicates the abnormality is
detected.
F0410.ai
Figure 4.7
4-14
<4. Diagnostics>
Display Example of H Side Blocking
The alarm display on LCD regarding the advanced
diagnostic is described in Table 4.5.
NOTE
The alarms of “Invalid Ref xx” and “ILBD over
range” do not link to the 4-20 mA analog signal
and Status output.
4.2.2.6 Condition Check
After the transmitter was installed, it is necessary to
confirm if Pres is stable under the normal operating
condition or if fluctuation amplitude under the
normal operating condition is large enough to detect
the blockage.
 Stability of Pressure Value
1) Observe the value change of Pres under the
normal operating condition for 10 minutes.
2) Confirm the value change is less than 10%.
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Detailed setup →
DTM (HART 7) Sensors → Pressure Sensor → Pres
DTM (HART 5) Configuration → Process Input → Pres
If the value change is more than 10%, the error
influences pressure fluctuation value so that the
blockage detection becomes impossible. Consider
the plant operating conditions.
 Fluctuation Value
NOTE
The blockage detection may not be carried
out correctly when pressure fluctuation
amplitude especially with the pressure and level
measurement, is small.
Confirm that each value of fDP, fSPl, fSPh, and
BlkF is more than the value specified in the below
table.
• Procedure to call up the fDP, fSPl, fSPh display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD parameters →
Status → Fluct Variables → fDP/fSPl/
fSPh
DTM (HART 5) Diag and Service → Advanced Diag
Variables → fDP/fSPl/fSPh
• Procedure to call up the BlkF display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD parameters →
Status → Diag Variables → BlkF
DTM (HART 5) Diag and Service → Advanced Diag
Variables → BlkF
Table 4.4
fDP
fSPI
fSPh
BlkF
Requirements to apply ILBD
Condition
7×10-10 or more
1×10-10 or more
1×10-10 or more
-0.5 to 0.5
IM 01C25T01-06EN
 fDP is not enough.
No blockage can be detected if fDP is not larger
than the specified value.
 Only fDP is enough.
“A Blocking” or “B Blocking” can be detected
if fSPl and fSPh are not larger than specified
values.
 fDP and fSPl are enough.
“H Side Blocking” and “Large Fluct H” can not
be detected if fSPh is not larger than specified
value.
 fDP and fSPh are enough.
“L Side Blocking” and “Large Fluct L” can not
be detected if fSPl is not larger than specified
value.
 fDP, fSPl and fSPh are enough.
All alarm modes can be detected even if BlkF is
not within the specified values.
4.2.2.7 Obtain Reference Values
The pressure fluctuation values are reduced
when the impulse line is plugged. Therefore, the
reference value is required to determine the degree
of reduction.
IMPORTANT
• If the impulse line is about to be plugged at
the time when a reference value is obtained,
blockages cannot be detected accurately.
The impulse lines on both the high-pressure
and low-pressure sides need to be cleaned
before a reference value is obtained.
• All air bubbles need to be adequately purged
before a reference value is obtained.
• Reference values must be obtained under
operating condition.
<4. Diagnostics>
4-15
 Start of Sampling
The sampling of reference value is carried out for
180 sec, which is the default value set to Diag
Period.
1) Confirm that the sampling period (Diag Period)
is set to 180 sec.
2) Set “Reference” to Diag Mode.
The sampling starts soon after the setting.
IMPORTANT
• For the each parameter, the one value is
given. If Reference is set to Diag Mode
again, the value is updated and overwritten.
• If the power supply is shut down during the
sampling, Diag Mode becomes “Stop”. Set
“Reference” to Diag Mode in order to carry
out the sampling again.
 End of Sampling
After about 180 sec, the sampling automatically
finishes. The “Reference” setting of Diag Mode
moves automatically to “Calculation”.
Confirm that the setting of Diag Mode moves to
“Calculation”.
 Reference Values
Confirm the latest values are obtained into the
following parameters.
• Ref fDP
• Ref fSPl
• Ref fSPh
• Ref BlkF
• Ref DPAvg
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD parameters →
Status → Diag Reference → Ref fDP/
Ref fSPl/Ref fSPh/Ref BlkF/Ref DPAvg
DTM (HART 5) Diag and Service → Advanced
Diag Configuration → Impulse Line
Blockage Detection → Ref fDP/Ref
fSPl/Ref fSPh/Ref BlkF/Ref DPAvg
IM 01C25T01-06EN
 Invalid Ref F, SPH, SPL, or DP
When the enough reference fluctuation value is
not obtained, an alarm of invalid reference value
for each parameter is generated and also the ILBD
operation is not carried out.
Confirm the alarm of Invalid Ref F, SPH, SPL, or
DP is not displayed in Diag Error.
If an alarm of Invalid Ref F, SPH, SPL, or DP is
generated, consider the process condition or obtain
the reference fluctuation values again.
NOTE
Even if an alarm of Invalid Ref F, SPH, SPL, or
DP is generated, “Calculation” in Diag Mode is
kept.
4.2.2.8 Capability Test of Blockage
Detection Operation
Before performing the ILBD operation, check the
capability of the blockage detection operation.
The simulation test is performed by closing motion
of a three-valve manifold or stop valve. When
simulated blockage occurs, confirm that an alarm is
generated.
NOTE
The fluctuation amplitude of atmospheric
pressure is nearly zero with pressure or level
measurement. In such case, simulate the
blockage detection by closing the valve where
the fluctuation existed.
 Simulation of High-pressure Side
Blockage
1)Close the high-pressure-side valve.
2)Confirm the value of Pres is stable. If not,
open the valve a little.
3)Set “Calculation” to Diag Mode so as to start
blockage detection operation.
4)Check that an alarm of “H Side Blocking” is
generated after the time that consists of Diag
Period and Diag Supp Count passed.
5)Check also the operation of the analog alert if
an analog alert is set.
6)Open the valve completely and check that
there are no alarms.
4-16
<4. Diagnostics>
 Simulation of Low-pressure Side
Blockage
1)Close the low-pressure-side valve.
2)Confirm the value of Pres is stable. If not,
open the valve a little.
3)Set “Calculation” to Diag Mode so as to start
blockage detection operation.
4)Check that an alarm of “L Side Blocking” is
generated after the time that consists of Diag
Period and Diag Supp Count passed.
5)Check also the operation of the analog alert if
an analog alert is set.
6)Open the valve completely and check that
there are no alarms.
 Simulation of Both-pressure Side
Blockage
1)Close the both-pressure-side valves.
2)Confirm the value of Pres is stable. If not,
open the valve a little.
3)Set “Calculation” to Diag Mode so as to start
blockage detection operation.
4)Check that an alarm of “B Blocking” is
generated in the Diag Error after the time
that consists of Diag Period and Diag Supp
Count passed.
5)Check also the operation of the analog alert if
an analog alert is set.
6)Open the valve completely and check that
there are no alarms.
4.2.2.9 Start ILBD Operation
If process condition and capability to detect a
blockage are confirmed, you can start the ILBD
operation according to the following procedure.
1)Check the value of sampling period (Diag
Period).
2)Check the number of times that detect the
blockage consecutively in order to give an
alarm (Diag Supp Count). The default value
at the shipment is set to 3 times.
3)Set “Calculation” to Diag Mode.
If the reference value has not yet been
obtained, set “Reference” to Diag Mode.
After obtained the reference values, the
ILBD starts automatically. At the same time,
Diag Mode changes automatically from
“Reference” to “Calculation”.
IM 01C25T01-06EN
4.2.2.10Tuning
(1) For DD (HART 5/HART 7) and DTM (HART 7)
When the pressure fluctuation amplitude in fluids is
not sufficiently large or an alarm is often generated
according to the process condition, tune up by
changing the threshold for the blockage detection
(Limit parameters) or the sampling period (Diag
Period) to enhance the accuracy of the blockage
detection The ILBD operation must be stopped to
tune up. Set “Stop” to Diag Mode.
 Threshold Value
The figure below shows the image of tuning effect
with a monochrome bar.
(a) The tuning image of the threshold values for
(1) Ratio fDP: Sqrt (fDP/Ref fDP),
(2) Ratio fSPl: Sqrt (fSPl/Ref fSPl),
(3) Ratio fSPh: Sqrt (fSPh/Ref fSPh)
0
1
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD parameters →
Configuration → Diag Lim →
The default values at the factory setting are the
values of Lim fDPmax to Lim BlkFmin shown in
Table 4.3.
Change the threshold value to solve your problem
according to the above image.
1) Set “Stop” to Set Diag Mode.
Note: Set to “Calculation” after setting the parameter.
Threshold (upper side)
(1) Lim fDPmin
(2) Lim fSPlmin
(3) Lim fSPhmin
• Procedure to call up the threshold related
display
2) Change the unsuitable value of Diag Lim
parameters corresponding to the each
blockage detection.
3
Threshold (lower side)
(1) Lim fDPmax
(2) Lim fSPlmax
(3) Lim fSPhmax
Limit parameter
#
Parameter
[1] Lim fDPmax
[2]
Lim fDPmin
[3]
Lim fSPlmax
[4]
Lim fSPlmin
[5]
Lim fSPhmax
[6]
Lim fSPhmin
[7]
Lim BlkFmax
[8]
Lim BlkFmin
F0411-1.ai
(b) The tuning image of the threshold values for
(4) Sqrt (BlkF/Ref BlkF)
-1
0
Threshold (lower side)
(4) Lim BlkFmin
1
Threshold (upper side)
(4) Lim BlkFmax
F0411-2.ai
Figure 4.8
4-17
<4. Diagnostics>
Tuning Image of Threshold Value
 Move the threshold toward the white.
• It becomes increasingly likely to give a false
alarm due to the disturbance from environment
change.
• If flow/differential pressure is below Lim
DPAvgmin or exceeds Lim DPAvgmax,
pressure fluctuation is likely too small or too
large to detect the blockage.
 Move the threshold toward the black.
• It enables to be insusceptible to disturbance
such as environment change and to detect the
blockage easier.
• It becomes giving an alarm of the blockage after
the blockage has been progressed.
Threshold value
Threshold to detect “A
Blocking” by using Ratio fDP
Threshold to detect “B
Blocking” by using Ratio fDP
Threshold to detect “Large
Fluct L” by using Ratio fSPl
Threshold to detect “L Side
Blocking” by using Ratio fSPl
Threshold to detect “Large
Fluct H” by using Ratio fSPh
Threshold to detect “H Side
Blocking” by using Ratio fSPh
Threshold to detect “H Side
Blocking” by using BlkF
Threshold to detect “L Side
Blocking” by using BlkF
(2) For DTM (HART 5)
Combination of threshold depend on the sensitivity
of blockage detection can be selected from High,
Medium, or Low in the Sensitivity parameter.
• Procedure to call up the display
DTM (HART 5) Diag and Service → Advanced
Diag Configuration → Impulse Line
Blockage Detection → Threshold →
sensitivity
When select “Custom” in the Sensitivity parameter,
you can set each threshold individually.
Set the Diag Mode to “Stop” before changing the
threshold.
IM 01C25T01-06EN
Combination of threshold for sensitivity parameter
High
Medium
Low
Lim fDPmax
1.50
3.00
3.00
Lim fDPmin
0.40
0.30
0.20
Lim fSPlmax
5.00
5.00
5.00
Lim fSPlmin
0.50
0.50
0.30
Lim fSPhmax
5.00
5.00
5.00
Lim fSPhmin
0.50
0.50
0.30
Lim BlkFmax
0.60
0.60
0.80
Lim BlkFmin
-0.60
-0.60
-0.80
 Sampling Period
If fluctuating around the threshold value, an
alarm maybe often generated. When the above
phenomenon happens, the sampling time (Diag
Period) can be changed so as to enhance the
accuracy of the blockage detection.
The longer the sampling time, better the expected
accuracy.
(1) Set “Stop” to Diag Mode.
(2) Enter the value to Diag Period within the
range of 20 to 65535 (sec).
Note: Set to “Calculation” after setting the parameter.
Also, the accuracy can be improved by increasing
the number of Diag Supp Count.
 ILBD Range Setting
If flow/differential pressure is less than the default
threshold value of Lim DPAvgmin, pressure
fluctuation is not large enough to detect the
blockage. To prevent the fault blockage detection,
the threshold should be changed to larger value.
(1) Set “Stop” to Diag Mode.
(2) Enter the value to Lim DPAvgmin or Lim
DPAvgmax.
4-18
<4. Diagnostics>
 Ratio fDP Compensation
When the flow change is too large or small, an
alarm maybe often generated. When the above
case happens, the Ratio fDP can be compensated
so as to enhance the accuracy of the blockage
detection.
 Diag DPComp
When “Compensation” is selected in Diag
DPComp, Ratio fDP is compensated by following
formula and used as treatable monitoring value,
CRatio fDP.
CRatio fDP
=
fDP
Ref fDP
Ref DPAvg
DPAvg
On the other hand, if the compensation is not
necessary, “Non-compensation” is selected in Diag
DPComp and Ratio fDP is used as NRatio fDP.
NRatio fDP
=
fDP
Ref fDP
• Procedure to call up the display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD parameters →
Status → Diag Vriables → CRatio fDP/
NRatio fDP
DTM (HART 5) Diag and Service → Advanced Diag
Variables → CRatio fDP/NRatio fDP
4.2.2.11 Reset of Reference Value
When there are large flow change or the change of
fluid conditions, obtain the reference value again. If
flow change by a comparison of the reference value
is ±25% or more, obtain the reference value again.
Note Set to “Calculation” after setting the parameter.
• Procedure to call up the threshold display
DD (HART 5/7) [Root Menu] → Diag/Service → Diag
DTM (HART 7) Parameters → ILBD parameters →
Configuration → Diag Lim →
DTM (HART 5) Diag and Service → Advanced
Diag Configuration → Impulse Line
Blockage Detection → Threshold →
IM 01C25T01-06EN
<4. Diagnostics>
4-19
4.2.2.12ILBD Parameter List
# Parameter name Default value
Explanation
1 Diag Error
0x0000
The results detected by ILBD or Heat trace monitoring are stored into this
parameter.
Also the condition abnormality in the diagnostic process is stored as an error.
2 Diag Option
0x08FC
The masking in this parameter enable to display each error message and the
status to the output signal or LCD.
The error assigned to each bit is corresponding to that of Diag Error.
Writable only when Diag Mode is "Stop".
3 Diag Out Option Off
Output mode of 4-20mA when an advanced diagnostic alarm is generated.
There are following three output modes; Off, Burnout, or Fall back.
4 Diag Fixed Out
21.6 mA
Parameter for "Fall back" function in the Diag Out option. The output value of
Val
4-20 mA analog signal is specified when an alarm is generated. The value can be
entered within 3.6 to 21.6 mA.
5 DO Select
Off
The variables for status output are specified to this parameter. When the
advanced diagnostic function (option code /DG6) is installed, the parameters
monitoring in diagnostic process can be also assigned to the status output.
6 Diag Mode
Stop
The operation mode of ILBD is set.
Stop:
The blockage detection is stopped.
Calculate: The blockage detection is carried out.
The alarms are generated along with the detected result.
Reference:The reference values are obtained and the update values are
overwritten.
After setting, this mode moves automatically to "Calculation".
7 Diag Period
180 (sec)
The data acquisition period for ILBD is set within 20 to 65535 (sec). If the process
fluctuation values are unsteady, this value is changed to the longer to enhance
the accuracy of the blockage detection.
Writable only when Diag Mode is "Stop".
8 Diag Supp Count 3
Detection count to generate an alarm. When the statistical value as Ratio fDP
and BlkF exceeds consecutively the threshold by number of times preset to this
parameter, it is estimated that the impulse line is plugged.
9 Diag Description
Memo field. 32 alphanumerics
10 fDP
11 fDP Status
12 fSPl
13 fSPl Status
14 fSPh
15 fSPh Status
16 BlkF
17 BlkF Status
18 DPAvg
19 DPAvg Status
20 Ratio fDP
21 Ratio fDP Status
22 Ratio fSPl
23 Ratio fSPl Status
24 Ratio fSPh
25 Ratio fSPh
Status
26 Ref fDP
27 Ref fDP Status
Average value of the sum of squares of differential pressure fluctuation.
Status of fDP
Average value of the sum of squares of low-pressure-side static pressure
fluctuation. For gauge/absolute pressure transmitter, 0 is set.
Status of fSPl
Average value of the sum of squares of high-pressure-side static pressure
fluctuation. For gauge/absolute pressure transmitter, 0 is set.
Status of fSPh
Blockage degree characterized in comparison of high- and low-pressure side
pressure fluctuation value.
Status of BlkF
Ratio of the average of differential pressure/pressure to the maximum span of an
EJX transmitter.
Status of DPAvg
CRatio fDP or NRatio fDP is used by Diag Comp setting.
fDP decreases and this parameter is used to determine whether one or both
sides are plugged.
Status of Ratio fDP
SQRT (fSPl/Ref fSPl).
fSPl decreases and this parameter is used to determine whether low-pressureside is plugged.
Status of Ratio fSPl
SQRT (fSPh/Ref fSPh).
fSPh decreases and this parameter is used to determine whether high-pressureside is plugged.
Status of Ratio fSPh
Value of fDP obtained under normal condition.
Status of fDP obtained under normal condition.
IM 01C25T01-06EN
#
28
29
30
31
32
33
34
35
Parameter name Default value
Ref fSPl
Ref fSPl Status
Ref fSPh
Ref fSPh Status
Ref BlkF
Ref BlkF Status
Ref DPAvg
Ref DPAvg
Status
36 Lim fDPmax
Refer to
Table 4.3
37 Lim fDPmin
38 Lim fSPlmax
39 Lim fSPlmin
40 Lim fSPhmax
41 Lim fSPhmin
42 Lim BlkFmax
43 Lim BlkFmin
44 Lim DPAvgmax
45 Lim DPAvgmin
46 Ref Lim fDPmin
7.0E-10
47 Ref Lim fSPmin
1.0E-10
48 Ref Lim BlkFmax 0.5
49 Status group 8
50 Status group 9
51 CRatio fDP
52 CRatio fDP
Status
53 NRatio fDP
54 NRatio fDP
Status
55 Diag DPComp
56 Diag Applicable
4-20
<4. Diagnostics>
Explanation
Value of fSPl obtained under normal condition.
Status of fSPl obtained under normal condition.
Value of fSPh obtained under normal condition.
Status of fSPh obtained under normal condition.
Value of BlkF obtained under normal condition.
Status of BlkF obtained under normal condition.
Value of DPAvg obtained under normal condition.
Status of DPAvg obtained under normal condition.
Upper limit for Ratio fDP to detect the blockage.
Writable only when Diag Mode is "Stop".
Lower limit for Ratio fDP to detect the blockage.
Writable only when Diag Mode is "Stop".
Upper limit for Ratio fSPl to detect the blockage.
Writable only when Diag Mode is "Stop".
Lower limit for Ratio fSPl to detect the blockage.
Writable only when Diag Mode is "Stop".
Upper limit for Ratio fSPh to detect the blockage.
Writable only when Diag Mode is "Stop".
Lower limit for Ratio fSPh to detect the blockage.
Writable only when Diag Mode is "Stop".
Upper limit for BlkF to detect the blockage.
Writable only when Diag Mode is "Stop".
Lower limit for BlkF to detect the blockage.
Writable only when Diag Mode is "Stop".
Upper limit for DPAvg. Writable only when Diag Mode is "Stop".
Lower limit for DPAvg. Writable only when Diag Mode is "Stop".
Lower limit to judge whether Ref fDP is available for ILBD operation.
Writable only when Diag Mode is "Stop".
Lower limit to judge whether Ref fSPl and Ref fSPh are available for ILBD
operation.
Writable only when Diag Mode is "Stop".
Upper limit to judge whether Ref BlkF is available for ILBD operation.
Writable only when Diag Mode is "Stop".
Refer to Table 4.5.
Refer to Table 4.5.
Ratio fDP is compensated by following formula and used as treatable monitoring
value when the flow change is too large or small.
Sqrt (fDP / Ref fDP) X | Ref DPAvg / DPAvg |
When compensation is selected in Diag DP Comp, CRatio fDP is used as
monitoring value.
Status of CRatio fDP
When Non-compensation is selected in Diag DP Comp, NRatio fDP is used as
monitoring value. NRatio fDP = Sqrt (fDP / Ref fDP)
Status of NRatio fDP
0:
Whether fDP is referred by CRatio fDP or NRatio fDP is selected.
Compensation
After the reference value is obtained, the applicable blockage detection is
displayed on this parameter.
IM 01C25T01-06EN
4-21
<4. Diagnostics>
4.2.3 Heat Trace Monitoring
4.2.3.1 Flg Temp Coef Setting
The transmitter with Heat trace monitoring function
calculates the flange temperature by using the two
temperature sensors built in the transmitter.
The value calculated according to the following
procedure is set to Flg Temp Coef.
An analog alert is generated if the temperature
reached to the preset level.
The flange temperature is based on the following
parameters and calculation formula.
[Parameters]
Parameter name
Snsr temp (CT)
Explanation
Measured capsule temperature
value
Amp temp (AT)
Measured amplifier temperature
value
Flg temp (FT)
Flange temperature value
(Calculated value)
Flg Temp Coef (Cf)
Coefficient to calculate flange
temperature
Flg Temp Hi Alert Val Threshold to generate FT high
alarm
Flg Temp Lo Alert Val Threshold to generate FT low
alarm
[Calculation formula]
Flg temp (FT) = CT + Cf X (CT-AT)
If the flange temperature exceeds the value preset
to Flg Temp Hi Alert Val or Flg Temp Lo Alert Val,
an alert is generated.
• To enhance the calculation accuracy of the
flange temperature, measure the actual flange
temperature by using the temperature sensor
etc.
• Calculate the ratio of the capsule temperature
to the capsule temperature minus the amplifier
temperature from the two temperature values
measured by the transmitter.
• Derive the Flg Temp Coef from the measured
flange temperature and the ratio of the capsule
temperature to the amplifier temperature in
accordance with the following calculation
formula.
Flg Temp Coef (Cf) =
(Actual measured value of Flange temperature) - CT
CT - AT
For DTM (HART 5), Flg Temp Coef parameter can
be set by using Tuning function.
By setting the measured value of flange
temperature, Flg Temp Coef is calculated by using
capsule temperature and amplifier temperature.
• Procedure to call up the Tuning display.
Diag and Service → Advanced Diag Configuration →
Heat Trace → Tuning
NOTE
The flange temperature is calculated by the
calculation formula assumed that the capsule
part of the transmitter is heated up or kept warm
by an electrical heater or steam. In the case of an
atmosphere temperature or less, the difference
of temperature of approximately 3 to 4 °C,
may occur because the amplifier temperature
becomes higher than the capsule temperature.
IM 01C25T01-06EN
4-22
<4. Diagnostics>
Sensor signals
Sensor
Amplifier
Temperature
Process Value
calculation
4-20mA DC
(Analog Output)
Amp temp
Capsule
Temperature
Amp temp
Snsr temp
Snsr temp
HTM alarm
Calculation of
Flg temp
Diag Output
Option
DO Config
HTM alarm
Contact Output
(Digital Output)
Flg Temp Coef
CT+(CT-AT) x Cf
Flg temp
Flg temp
Result of HTM detection
Execution HTM
Alarm Masking
Result of HTM detection
HTM alarm
Figure 4.9
Diag Error
Response Code
(Device Status)
Status group 9
Display on LCD
F0412.ai
Functional Block Diagram of Heat Trace Monitoring (HTM)
4.2.3.2 Out of Temperature Measurement
Range
When the flange temperature is out of
measurement range, the alarm or alert is
generated. For the detail of alarm and alert setting,
refer to subsection 4.2.2.5.
The measurement range is set to Flg Temp Hi
Alert Val and Flg Temp Lo Alert Val, which values
can be specified within -50 to 130 deg C.
An alarm is generated.
Flg Temp Hi Alert
Flg Temp Lo Alert
Flg
temp
Flgtemp
An alarm is generated.
Time
F0413.ai
IM 01C25T01-06EN
<4. Diagnostics>
4-23
4.2.3.3 Parameter Lists for Heat Trace Monitoring
#
Parameter name
1 Diag Error
2
3
4
5
6
7
8
9
10
11
12
13
*1:
*2:
Default value
Explanation
0x0000
The results detected by ILBD or Heat trace monitoring are stored into this
parameter. Also the condition abnormality in the diagnostic process is
stored as an error.
Diag Option
0x08FC
The masking in this parameter enable to display each error message and
the status to the output signal or LCD.
The error assigned to each bit is corresponding to that of Diag Error.
Writable only when Diag Mode is "Stop".
Diag Out Option
Off
The error status can be output by 4-20 mA analog signal.
There are following three output modes; Off, Burnout, or Fall back.
Diag Fixed Out Val
21.6mA
Parameter for "Fall back" function in the Diag Out option.
The output value in 4-20 mA analog signal is specified when an alarm is
generated.
The value must be entered within 3.6 to 21.6 mA.
Snsr temp (Cap temp*2)
Measured capsule temperature value
Amp temp
Measured Amplifier temperature value
Calculated flange temperature value
Flg temp
(*1)
Flg Temp Coef
0
Coefficient to calculate flange temperature (Cf: Rt1/Rt2)
Rt1: Thermal resistance between the flange and capsule.
Rt2 : Thermal resistance between the cupsule and amplifier.
Flg Temp Hi Alart Val
120 deg C
Upper limit of Flg temp
(Flg Temp High Limit*2)
Flg Temp Lo Alart Val
-40 deg C
Lower limit of Flg temp
(Flg Temp Low Limit*2)
DO Select
Off
See subsection 3.3.13 Status Output
DO Signal type
ON WHEN
See subsection 3.3.13 Status Output
AL DETECT
Digital Output
Off
See subsection 3.3.13 Status Output
The Flg Temp Coef is 0 at the shipment so that the Flg temp outputs the same value as that of Snsr temp.
For DTM (HART 5)
IM 01C25T01-06EN
4-24
<4. Diagnostics>
4.3 Alarms and Countermeasures
AL. 01
CAP.ERR
HART configuration
tool display
Cause
4-20mA Output
operation during error
P sensor error *1
Pressure Sensor
Error *2
Sensor problem.
CT sensor error *1
Capsule Temperature
Sensor Error *2
Cap EEPROM error *1
Capsule EEPROM
Error *2
AT sensor error *1
Amp Temp Sensor
Error *2
Amp EEPROM error *1
Amp EEPROM Error
*2
CPU board error *1
CPU Board Error *2
AD Converter Error *1
A/D Converter Error *2
No device ID *1
No Device ID *2
P outside limit *1
Pressure Outside
Limit *2
Capsule temperature
sensor problem.
AL. 11
ST. PRSS
SP outside limit *1
Static Pressure
Outside Limit *2
Static pressure exceeds
limit.
AL. 12
CAP.TMP
CT outside limit *1
Cap Temp Outside
Limit *2
AT outside limit *1
Amp Temp Outside
Limit *2
P over range *1
Pressure Over Range
*2
Capsule temperature is
outside range (–50 to
130°C).
Amplifier temperature
is outside range (–50 to
95°C).
Differential pressure
When PV is Pres.
exceeds specified range. Output AO upper limit or
lower limit.
(Refer to subsection 3.3.1)
Static pressure exceeds When PV is SP
specified range.
Output AO upper limit or
lower limit.
(Refer to subsection 3.3.1)
Input pressure exceeds
Continues to operate and
specified threshold.
output.
AL. 02
AMP.ERR
—
AL. 10
PRESS
AL. 13
AMP.TMP
AL. 30
PRS.RNG
AL. 31
SP. RNG
AL. 35 P.HI
SP over range *1
Static Pressure Over
Range *2
Outputs the signal (High
or Low) set with burnout
direction switch.
[status output: undefined]
(About the output signal,
refer to subsection 3.3.9)
Countermeasure
Status Diagnostic
group
List
*1
group *2
Replace capsule if
the error recurs after
the transmitter is
restarted.
Replace capsule.
Capsule EEPROM
problem.
1
Amplifier temperature
sensor problem.
Replace amplifier.
Amplifier EEPROM
problem.
Amplifier problem.
2
A/D Converter problem.
No device ID is found.
Differential pressure is
outside measurement
range limit of capsule.
P high alarm *1
Pressure High Alarm *2
AL. 36 P.LO P low alarm *1
Pressure Low Alarm *2
AL. 37
SP high alarm *1
Input static pressure
SP.HI
Static Pressure High
exceeds specified
Alarm *2
threshold.
AL. 38
SP low alarm *1
Static Pressure Low
SP.LO
Alarm *2
Hardware Failure
Integral
indicator
Alarm Message Summary
4
Continues to operate and
output.
When PV is Pres
Output AO upper limit or
AO Lower limit. (Refer to
subsection 3.3.1)
When PV is SP
Output AO upper limit or
AO Lower limit. (Refer to
subsection 3.3.1)
Continues to operate and
output.
Replace amplifier.
2
Check input or
replace capsule
when necessary.
3
Use heat insulation
or make lagging to
keep temperature
within range.
Check input and
range setting, and
change them as
needed.
4
Transducer Status
Table 4.5
Check input.
5
*1: DD (HART 5/HART 7), DTM (HART 7/EJA: HART 5)
*2: DTM (EJX: HART 5)
*3: Available only for HART 7
IM 01C25T01-06EN
AL. 50
P. LRV
AL. 51
P. URV
AL. 52
P. SPN
AL. 53
P. ADJ
AL. 54
SP. RNG
AL. 55
SP. ADJ
AL. 79
OV. DISP
AL.87
FLG. HI
AL.87
FLG. LO
HART configuration
tool display
Cause
4-20mA Output
operation during error
Countermeasure
Illegal P LRV *1
Illegal Pressure LRV
*2
Illegal P URV *1
Illegal Pressure URV
*2
Illegal P SPAN *1
Illegal Pressure SPAN
*2
P SPAN trim err *1
Pressure SPAN Trim
Error *2
P ZERO trim err *1
Pressure ZERO Trim
Error *2
Illegal SP LRV *1
Illegal Static Pressure
LRV *2
Illegal SP URV *1
Illegal Static Pressure
URV *2
Illegal SP SPAN *1
Illegal Static Pressure
SPAN *2
SP SPAN trim err *1
Static Pressure SPAN
Trim Error *2
SP ZERO trim err *1
Static Pressure ZERO
Trim Error *2
—
Specified value is outside Holds at the output value
of setting range.
that existed immediately
before the error occurred.
Check settings and
change them as
needed.
Continues to operate and
output.
Adjust settings and
change them as
needed.
FT high alarm *1
Flg Temp High Alarm
*2
FT low alarm *1
Flg Temp Low Alarm
*2
Flange temperature
exceeds a preset upper
limit.
Flange temperature is
below a preset lower
limit.
AL.88
INVR.DP
Invalid Ref DP *1
Invalid Ref fDP *2
AL.88
INVR.SL
Invalid Ref SPL *1
Invalid Ref fSPl *2
AL.88
INVR.SH
Invalid Ref SPH *1
Invalid Ref fSPh *2
AL.88
INVR.F
Invalid Ref F *1
Invalid Ref BlkF *2
AL.89
ILBD.OV
ILBD over range *1
Outside Diagnosis
Range *2
Holds at the output value
that existed immediately
before the error occurred.
Check settings and
change them as
needed.
Specified value is outside Continues to operate and
of setting range.
output.
Adjust settings and
change them as
needed.
Displayed value exceeds Continues to operate and
limit.
output.
It depends on the Diag Out
Option setting.
Off: Continue to operate and
output.
Burnout:Outputs AO upper
limit or AO lower limit.
Fall back:Outputs Diag Out
Fixed Val.
Differential pressure/
Continue to operate and
pressure fluctuation does output.
not reach the reference
level required to blockage
detection so that no
blockage detection is
carried out.
Low-pressure-side
fluctuation does not
reach the reference
fluctuation level required
to blockage detection.
High-pressure-side
fluctuation fluctuation does
not reach the reference
fluctuation level required to
blockage detection.
BlkF can not be used for
blockage detection for
some reasons.
Appointed the diagnosis
range outside.
Check settings and
change them as
needed.
Check the heater
failure.
Status Diagnostic
group
List
*1
group *2
6
Configuration
Integral
indicator
4-25
<4. Diagnostics>
7
—
Check the capsule
temp. and Amplifier
temp.
Adjust Flg Temp
Coef.
Check process
condition.
8
Diag Status
*1: DD (HART 5/HART 7), DTM (HART 7/EJA: HART 5)
*2: DTM (EJX: HART 5)
*3: Available only for HART 7
IM 01C25T01-06EN
HART configuration
tool display
Cause
AL.89
B BLK
B Blocking *1, *2
B Blocking (both-side
blockage) is detected.
AL.89
H BLK
H Side Blocking *1
High Side Blocking *2
High-pressure-side
blockage is detected.
AL.89
L BLK
L Side Blocking *1
Low Side Blocking *2
Low-pressure-side
blockage is detected.
AL.89
H LRG
Large Fluct H *1
Large Fluctuation of
High Side *2
Large Fluct L *1
Large Fluctuation of
Low Side *2
A Blocking *1, *2
Pressure fluctuation
amplitude of highpressure side is large.
Pressure fluctuation
amplitude of lowpressure side is large.
A Blocking (single-side
blockage) is detected.
AL. 91 *3
P. SIM
P Simulate Mode
Under Simulation Mode
for device variables.
AL.91 *3
SP. SIM
SP Simulate Mode
AL.91 *3
T. SIM
T Simulate Mode
AL.89
L LRG
AL.89
A BLK
4-20mA Output
operation during error
It depends on the Diag Out
Option setting.
Countermeasure
Check process
condition.
Off: Continue to operate and
output.
Burnout: Outputs AO upper
limit or AO lower limit.
Fall back: Outputs Diag Out
Fixed Val.
Output the setting value of
Simulate-Value
Status Diagnostic
group
List
*1
group *2
9
Diag Status
Integral
indicator
4-26
<4. Diagnostics>
10
—
Check Simulation
Mode
*1: DD (HART 5/HART 7), DTM (HART 7/EJA: HART 5)
*2: DTM (EJX: HART 5)
*3: Available only for HART 7
Table 4.6
HART Configuration Tool Error Messages
Error message
Invalid selection
Value was too high
Value was too low
Too few data bytes received
In write protect mode
Lower range value too high
Lower range value too low
Upper range value too high
Upper range value too low
Span too small
Applied process too high
Applied process too low
New lower range value pushed upper
range value over upper sensor limit
Excess correction attemted
Lower conversion not succeeded
Not in fixed current mode
In multidrop mode
Not write protect mode
Lower range value and upper range
value out of limits
Probable cause
—
Set value is too high.
Set value is too low.
—
Operation is set in the Write Protect mode.
LRV set point is too high.
LRV set point is too low.
URV set point is too high.
URV set point is too low.
Set span is too small.
Applied pressure is too high.
Applied pressure is too low.
The shift of URV according to the new LRV
setting exceeds USL.
Amount of correction is too much.
Characters are not convertible. e.g. %
The fixed current mode is desired but not
set in that mode.
Operation is set in the multi-drop mode.
Operation is set without a password.
URV and LRV are out of range limits.
Countermeasure
Change the setting.
—
—
Change the range.
Adjust the applied pressure.
Change the URV setting within the
range of USL.
Adjust the amount.
Correct the setting.
Set in the fixed current mode.
—
—
Change the setting.
IM 01C25T01-06EN
Table 4.7
Device Status
Item
Table 4.9
Description
Field Device Malfunction
(0x80)
Field device has
malfunctioned due to a
hardware error or failure.
Configuration Changed
(0x40)*
A modification has been
made to the configuration
of the field device.
Cold Start
(0x20)
A reset of the field device
has occurred, or power
has been removed and
reapplied.
More Status Available
(0x10)
Field device has more
status available.
Loop Current Fixed
(0x08)
Analog output and its
digital representation
are in fixed mode, and
not responsive to input
changes.
Loop Current Saturated
(0x04)
Analog output and its
digital representation are
outside the operating
range limits, and not
responding to input.
Non-Primary Variable Out
of Limits
(0x02)
Process applied to the
non-primary variable is
outside the operating
limits of the field device.
Primary Variable Out of
Limits
(0x01)
Process applied to the
primary variable is outside
the operating limits of the
field device.
*: 4-27
<4. Diagnostics>
Data Quality and Limit Status
Data Quality
Description
Good
The value may be used in
control.
Poor Accuracy
The quality of the value is
less than normal, but the
value may still be useful.
Manual / Fixed
The value is manually
fixed.
Bad
The value is not useful.
Limit Status
Description
Constant
The value cannot be
changed, no matter what
the process does.
Low Limited
The value is out of the
high or low limit.
High Limited
Not Limited
The value is free to
change.
This flag can be reset. Refer to subsection 4.1.3 (6) Reset
Configuration Changed Flag
Table 4.8
Extended Device Status
Item
Description
Maintenance Required
(0x01)
Device requires
maintenance.
Device Variable Alert
(0x02)
Configuration is invalid or
device is under simulation
mode.
IM 01C25T01-06EN
<4. Diagnostics>
Table 4.10
Integral
Indicator
AL.01
CAP.ERR
Relationship between Alarm and Status available for HART 7
HART
configuration
tool display
Device Status
Extended
Device Status
Value and Status (Data Quality and Limit Status)
Differential
Pressure
(DP)
Static
Pressure
(SP)
P sensor error
Device
Malfunction
CT sensor error (0x80)
Temperature
(T)
Maintenance Value: Hold value
Required
Status: Bad and Constant
(0x01)
Value: Hold value
Status: Bad and Constant
Cap EEPROM
Value: Hold value
error
Status: Bad and Constant
AL.02
AT sensor error
Value: Hold value
AMP.ERR
Status: Bad and Constant
Amp EEPROM
Value: Hold value
error
Status: Bad and Constant
CPU board
Value: Hold value
error
Status: Bad and Constant
AD Converter
Value: Hold value
error
Status: Bad and Constant
--No device ID
----Value: Measured value
Status: Good and Not Limited
AL.10
P outside limit Primary
Device
Value:
Value:
PRESS
Variable Out of Variable Alert Measured value
Measured
Limits (0x01) (0x02)
Status:
value
Poor Accuracy and Not
Status:
Limited
Good and Not
Limited
AL.11
ST.PRSS
SP outside limit Non-Primary
Variable Out of
Limits (0x02)
AL.12
CAP.TMP
CT outside limit Non-Primary
Variable Out of
Limits (0x02)
AT outside limit
AL.13
AMP.TMP
P over range
AL.30
PRS.RNG
Value: Measured value
Status: Good and Not Limited
AL.35
P. HI
AL.36
P. LO
AL.37
SP. HI
AL.38
SP. LO
AL.50
P. LRV
P high alarm
Value: Measured value
Status: Good and Not Limited
AL.51
P. URV
Illegal P URV
AL.52
P. SPN
Illegal P SPAN
---
% range
Loop current
Value:Hold value
Status:Bad and Low Limited/
High Limited*1
Value: Hold value
Status: Bad and Low Limited/
High Limited*1
Same as Value and Status of
PV
Value: Measured value
Status: Good and Not Limited
Loop Current
Saturated
(0x04)
SP over range ---
AL.31
SP. RNG
4-28
Value: Hold value
Status: Bad and Low Limited/
High Limited*2
Value: Measured value
Status: Good and Not Limited
P low alarm
SP high alarm
SP low alarm
Illegal P LRV
Value: Measured value
Status: Good and Not Limited
Value: Hold value
Status: Bad and Constant
*1: Depend on the setting of hardware switch
*2: Depend on the direction of range over (high or low)
IM 01C25T01-06EN
Integral
Indicator
AL.53
P. ADJ
<4. Diagnostics>
HART
configuration
tool display
Device Status
P SPAN trim err ---
P ZERO trim
err
AL.54
SP. RNG
Extended
Device Status
Value and Status (Data Quality and Limit Status)
Differential
Pressure
(DP)
Device
Value:
Variable Alert Measured
(0x02)
value
Status:
Poor
Accuracy and
Not Limited
Illegal SP LRV
4-29
Static
Pressure
(SP)
Temperature
(T)
Value:
Measured value
Status:
Good and Not Limited
Value: Measured value
Status: Good and Not Limited
% range
Loop current
Value: Measured value
Status: Poor Accuracy and Not
Limited
Value: Measured value
Status: Good and Not Limited
Illegal SP URV
Illegal SP
SPAN
AL.55
SP. ADJ
SP SPAN trim
err
Value:
Measured
value
Status:
Good and Not
Limited
SP ZERO trim
err
AL.79
OV.DISP
AL.87
FLG. HI
(None)
---
FT high alarm
---
AL.87
FLG. LO
FT low alarm
Value:
Measured
value
Status:
Poor
Accuracy and
Not Limited
Value: Measured value
Status: Good and Not Limited
Maintenance Value: Measured value
Required
Status: Good and Not Limited
(0x01)
Value:
Value: Measured value
Measured
Status: Good and Not Limited
value
Status:
Good and Not
Limited
---
AL.88
Invalid Ref DP
INVR.DP
AL.88
Invalid Ref SPL
INVR.SL
AL.88
Invalid Ref
INVR.SH SPH
AL.88
Invalid Ref F
INVR.F
*1: Depend on the setting of hardware switch
*2: Depend on the direction of range over (high or low)
In the case “Off” is set to Diag
Out Option
Value: Measured value
Status: Good and Not Limited
In the case “Burnout” is set to
Diag Out Option
Value: Low Limited/High
Limited
Status: Bad and Low Limited/
High Limited*1
In the case “Fall back” is set to
Diag Out Option
Value: Fixed value
Status: Bad and Constant
Value: Measured value
Status: Good and Not Limited
IM 01C25T01-06EN
Integral
Indicator
<4. Diagnostics>
HART
configuration
tool display
AL.89
ILBD.OV
AL.89
B BLK
ILBD over
range
B Blocking
AL.89
H BLK
H Side
Blocking
AL.89
L BLK
L Side Blocking
AL.89
H LRG
Large Fluct H
AL.89
L LRG
Large Fluct L
AL.89
A BLK
A Blocking
AL.91
P. SIM
P Simulate
Mode
AL.91
SP.SIM
SP Simulate
Mode
AL.91
T.SIM
T Simulate
Mode
Device Status
---
---
Extended
Device Status
4-30
Value and Status (Data Quality and Limit Status)
Differential
Pressure
(DP)
Static
Pressure
(SP)
Temperature
(T)
Maintenance Value: Measured value
Required
Status: Good and Not Limited
(0x01)
Value: Measured value
Status: Good and Not Limited
Device
Value and
Variable Alert Status:
(0x02)
Pressure
simulation
value
Loop current
In the case “Off” is set to Diag
Out Option
Value: Measured value
Status: Good and Not Limited
In the case “Burnout” is set to
Diag Out Option
Value: Low Limited/High
Limited
Status: Bad and Low Limited/
High Limited*1
In the case “Fall back” is set to
Diag Out Option
Value: Fixed value
Status: Bad and Constant
Value: Measured value
Status: Good and Not
Limited
Value and
Status:
Static
Pressure
simulation
value
Value: Measured value
Status: Good and Not
Limited
% range
According to the setting of
simulation
Value: Measured value
Status: Good and Not Limited
Value and
Status:
Temperature
simulation
value
*1: Depend on the setting of hardware switch
*2: Depend on the direction of range over (high or low)
IM 01C25T01-06EN
5.
Function
Analog output
Analog output
trim
Bi-directional
mode
Burst mode
5-1
<5. Parameter Summary>
Parameter Summary
Label
AO alm typ
AO lower limit
AO upper limit
Auto recover
Clear D/A trim
D/A trim
Scaled D/A trim
Channel flags
Bi-dir mode
Item
Analog output alarm type
Lower limit of analog output
Upper limit of analog output
Auto-recover from hardware error
Reset analog output trim
Analog output trim with ammeter
Analog output trim with voltmeter
Analog channel flags
Bi-directional mode
Contents
High or Low
3.6000 to 21.6000 mA
3.6000 to 21.6000 mA
Off or On
Burst mode
Burst mode *2
Off or On HART 5
Off or Wired HART Enabled
Off or On
Default value Handling *1
R
3.6000 mA
W
21.6000 mA
W
On
W
M
M
M
0x00
R
Off
W
Off
W
HART 7
Burst option
Burst option
Xmtr Variables, PV, % range/
current, Process vars/crnt
Burst Command *2
Cmd 1: PV
Cmd 2: % range/current
Cmd 3: Dyn vars/current
Cmd 9: Device vars w/status
Cmd 48: Read Additional
Device Status.
Max 8 slots.
HART 5
Burst Command
HART 7
Burst Variable
Code (DD)
Device Variable
Code (DTM)
Device Variable for the Burst
Message *2
W
Cmd 1: PV
W
W
HART 7
Burst Msg Trigger
Mode
Burst Trigger Mode Selection Code (Continuous, Window, Rising, Continuous
*2
Falling, On-change)
R
Configure burst trigger
Configure Burst Msg Trigger
Mode and Burst Trigger Level
M
Configure burst period
Configure Update Period and
Max Update Period
M
HART 7
Set Burst Trigger
HART 7
Set Burst Period
HART 7
Burst Trigger Level
Burst Trigger Level *2
0.0
R
Burst Message
1: 0.5sec
2: 60sec
3: 60sec
60 min
R
HART 7
Update Period
Update Period for Burst mode *2
HART 7
Damping
Date
Descriptor
*1:
*2:
*3:
Update period for burst
message
Max Update Period Max Update Period for Burst mode
*2
HART 7
Maximum update period for
burst message
Pres Damp
Quick resp
Date
Descriptor
0.00 to 100.00 sec
On or Off
**/**/**
16 alphanumerics
Damping time constant for DP
Quick response
Date
Descriptor
Off
R
W
W
W
W
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
Device
information
<5. Parameter Summary>
Label
Chg universal rev
Country
Item
Change the HART universal
revision
Country code
Contents
HART 5 or HART 7
US, JP, DE, FR, ES, RU, CN
5-2
Default value Handling *1
M
JP
W
HART 7
Dev id
Distributor
Drain vent matl
Extra No.
Ext SW
Fill fluid
Final asmbly num
Fld dev rev
Gasket matl
Isoltr matl
Mftr Date
Model 1
Model 2
Model 3
Num of RS
Process Conn matl
Process Conn size
Process Conn type
RS fill fluid
RS Isoltr matl
RS type
Serial No.
Sofftware rev
Style No.
Universal rev
Cfg chng count
Device ID
Yokogawa
Drain and vent plug material
Customizaion number
External zeroing permission
Fill fluid
Final assembly number
Field device revision
Gasket material
Capsule material
Manufactured date
Memo field for MS code 1
Memo field for MS code 2
Memo field for MS code 3
Number of remote seal
Process connection material
Process connection size
Process connection type
Fill fluid of remote seal
Remote seal material
Remote seal type
Serial number
Software revision
Style number
Universal revision
Configuration change counter
Disabled or Enabled
Enabled
32 alphanumerics
32 alphanumerics
32 alphanumerics
Style number of product
16 alphanumerics
0
R
R
W
R
W
W
W
R
W
W
R
W
W
W
W
W
W
W
W
W
W
R
R
R
R
R
HART 7
Reset Cfg chng flag Reset Configuration change flag
M
HART 7
Device Profile
Device Profile
Process
automation
device
3
HART 7
Max dev vars
Max device variables
R
R
HART 7
Model
Device
Simulate
Variable
HART 7
Simulation
Diag
Diag Applicable
Applicable
Diag DPComp Diag DPComp
Diag Error
*1:
*2:
*3:
Diag Error
Model
Execution of device variable
simulation
Model name + Measurement
span in the Suffix Codes
Ex) “EJX110 M”
Execute the simulation
Appicable blockage detection
Disabled or Enabled
fDP compensation selection
Compensation or
Non-compensation
Results detected by ILBD or Heat
trace monitoring
R
M
RG
Compensation
WG
RG
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
Diag Lim
<5. Parameter Summary>
Diag Mode
Label
Lim fDPmax
Lim fDPmin
Lim fSPlmax
Lim fSPlmin
Lim fSPhmax
Lim fSPhmin
Lim BlkFmax
Lim BlkFmin
Lim DPAvgmax
Lim DPAvgmin
Diag Mode
Item
Upper limit for Ratio fDP
Lower limit for Ratio fDP
Upper limit for Ratio fSPl
Lower limit for Ratio fSPl
Upper limit for Ratio fSPh
Lower limit for Ratio fSPh
Upper limit for BlkF
Lower limit for BlkF
Upper limit for DPAvg
Lower limit for DPAvg
ILBD operation mode
Diag Option
Diag Output
Diag Option
Diag Out Option
Alarm masking
Output mode of 4-20mA when
Off, Burnout, or Fall back
an advanced diagnostic alarm is
generated
4-20 mA output when an advanced 3.6000 to 21.6000 mA
diagnostic alarm is generated
Sampling period per one Diag count
Memo field
32 alphanumerics
Reference value of fDP
Status of Reference fDP
Reference value of fSPl
Status of Reference fSPl
Reference value of fSPh
Status of Reference fSPh
Reference value of BlkF
Status of Reference BlkF
Reference value of DPAvg
Status of Reference DPAvg
Lower limit of fDP
Lower limit of fSPl and fSPh
Upper limit of BlkF
Detection count to generate an
alarm
SQRT (fDP/Ref fDP).
Status of Ratio fDP
SQRT (fSPl/Ref fSPl).
Status of Ratio fSPl
SQRT (fSPh/Ref fSPh).
Status of Ratio fSPh
Blockage degree characterized in
comparison of high-pressure side
and low-pressure side pressure
fluctuation values
Status of BlkF
Ratio of the average of differential
pressure/pressure to the maximum
span of an EJX transmitter.
Status of DPAvg
Compensated fDP
Status of CRatio fDP
Non-compensated fDP
Status of NRatio fDP
Diag Fixed Out Val
Diag Period
Diag
Reference
Diag Ref Lim
Diag Period
Diag Description
Ref fDP
Ref fDP Status
Ref fSPl
Ref fSPl Status
Ref fSPh
Ref fSPh Status
Ref BlkF
Ref BlkF Status
Ref DPAvg
Ref DPAvg Status
Ref Lim fDPmin
Ref Lim fSPmin
Ref Lim BlkFmax
Diag Supp Count
Diag Supp
Count
Diag Variables Ratio fDP
Ratio fDP Status
Ratio fSPl
Ratio fSPl Status
Ratio fSPh
Ratio fSPh Status
BlkF
BlkF Status
DPAvg
DPAvg Status
CRatio fDP
CRatio fDP Status
NRatio fDP
NRatio fDP Status
*1:
*2:
*3:
Contents
Stop, Calculation, or
Reference
5-3
Default value Handling *1
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
Refer to Table 4.2.3
WG
WG
Off
WG
WG
21.6 mA
WG
180 sec
WG
WG
WG
RG
WG
RG
WG
RG
WG
RG
WG
RG
WG
WG
WG
WG
7.0E-10
1.0E-10
0.5
RG
RG
RG
RG
RG
RG
RG
RG
RG
RG
RG
RG
RG
RG
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
Display setup
Label
Bar Indicator
Chg power on info
Disp Out 1
Item
Bar indicator
Change the LCD display when
powering on
LCD output 1
Disp Out 2
LCD output 2
Disp Out 3
Disp Out 4
Disp Pres % fnctn
LCD output 3
LCD output 4
% display mode
Disp Pres % Reso
Engr exp
% display resolution
User set exponent
Engr LRV
Engr point
Engr URV
Modify Engr Unit
Pres disp point
User set lower range value
Decimal place for user set
User set upper range value
User set engineering unit
Decimal place for differential
pressure
Engineering unit select
Decimal place for static pressure
Squawk
Set Engr Unit
SP disp point
Squawk
HART 7
Error log
Event
Notification
5-4
<5. Parameter Summary>
Error log Clear
Error log view
Event Notification
Control
Clear error records
Error records
Event Notification
HART 7
Device Status
Mask
Contents
Off or On
On or Off
PRES, PRES %,
ENGR.PRES, SP, SP %
PRES, PRES %,
ENGR.PRES, SP, SP % or
Not used
(Ditto)
(Ditto)
Linear or Sq root
Default value Handling *1
On
W
M
PRES %
W
Not used
W
Not used
Not used
As specified or
Linear
Normal or High resolution
Normal
---, x10, x100, x1000
--- or as
specified
Unit specified in Set Engr Unit As specified
0 to 4
2
Unit specified in Set Engr Unit As specified
0 to 4
2
0 to 4
2
Specify the device under the
communication (turn the LCD
on).
Log1 (latest) to log4
(Enable event notification on
token-passing data link layer,
Off)
Off
W
W
W
W
W
W
W
W
M
W
M
WD
M
M
M
W
Event Masking
W
Configure Event Notification Timing Configure Event Notification
Retry Time, Event Max
Update Time and Event
Debounce Interval
M
HART 7
Status group 1 to
10 Mask
HART 7
Ext dev status
Mask
HART 7
Device Diagnostic
Status 0 Mask
HART 7
Device Diagnostic
Status 1 Mask
HART 7
AO saturated Mask
HART 7
AO fixed Mask
HART 7
Set Event
Notification Timing
HART 7
*1:
*2:
*3:
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
Event
Notification
5-5
<5. Parameter Summary>
Label
Event Notification
Retry Time
Item
Event Notification Retry Time
Contents
Default value Handling *1
R
HART 7
Max Update Time
HART 7
Event Debounce
Interval
Max Update Time for Event
Notification
Event Debounce Interval
R
Debounce Interval to detect
an event.
R
HART 7
Acknowledge Event Acknowledge Event Notification
Notification
W
HART 7
Event Status
Event Status
HART 7
Event Number
0x00 Approved event or no
event
0x10 Configuration changed
event pending
0x20 Device status event
pending
0x40 More status available
event pending
R
Event Number
W
Time First Unack Event Triggered
W
Latched Cfg chng count
W
Device status when event occurred
W
Field device status when event
occured
W
Calculated flange temperature
value
RG
HART 7
Time First Unack
Event Triggered
HART 7
Latched Cfg chng
count
HART 7
Latched Device
Status
HART 7
Latched Status
group 1 to 10
HART 7
Latched Ext dev
status
HART 7
Latched Device
Diagnostic Status 0
HART 7
Latched Device
Diagnostic Status 1
HART 7
Latched AO
saturated
HART 7
Latched AO fixed
HART 7
Flg temp
Flg temp
Flg Temp Coef Flg Temp Coef
Flg Temp Lim Flg Temp Hi Alart
Val
Flg Temp Lo Alart
Val
*1:
*2:
*3:
Upper limit of Flange temperature
0
120 °C (deg C)
WG
WG
Lower limit of Flange temperature
-40 °C (deg C)
WG
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
Fluct Variables fDP
Label
fDP Status
fSPl
fSPl Status
fSPh
Loop test
fSPh Status
Loop test
Test Auto Release
Time
Low cut
Master test
Message
Number of
requested
preambles
5-6
<5. Parameter Summary>
Item
Average value of the sum of
squares of differential pressure/
pressure fluctuations
Status of fDP
Average value of the sum of
squares of low-pressure-sidestatic
pressure fluctuations
Status of fSPl
Average value of the sum of
squares of high-pressure-side
static pressure fluctuations
Status of fSPh
Test output setting
Low cut
Auto release time for the test
function. Coverage is Loop test,
DO test and Device Variable
Simulation.
Low cut
Low cut mode
Master test
Message
Num req preams
Low cut mode
Software reset and self test
Message
Number of requested preambles
Num resp preams
Number of response preambles
Contents
Default value Handling *1
RG
RG
RG
RG
RG
Within AO lower and upper
limits
10min, 30min, 60min, 3h,
6h, 12h
RG
M
10 min
W
W
Linear or Zero
Refer to
subsection
3.2.6
Linear
32 alphanumerics
As specified
0.00 to 20.00%
W
M
W
R
5
W
HART 7
Optional
function
Piping
orientation
Poll address
H/L Swap
Optional function activation
password
Impulse piping accessing direction
Poll addr
Poll address for multidrop use
Loop current mode
Loop current mode in Multi Drop
mode
Option Password
W
Normal or Reverse
Normal
0 to 15(HART 5), 0 to
63(HART 7)
(Disabled, Enabled)
0
W
Disabled
W
Display of contact output
Off or On
Off
RA
Contact output select
Off, Combination of Pres, SP
and Temp
Off
WA
Signal type select
ON WHEN AL. DETECT, OFF ON WHEN AL.
WHEN AL. DETECT
DETECT
WA
Test output contact
Status High, Status Low, Exit
MA
Pres Alert Mode
Alert Mode for differential pressure
W
Hi Alert Val
SP Alert Mode
High alert value for differential
pressure
Low alert value for differential
pressure
Alert Mode for static pressure
SP Hi Alert Val
High alert value for static pressure
SP Lo Alert Val
Low alert value for static pressure
Temp Alert Mode
Alert Mode for temperature
Off, Hi Al Detect,Lo Al Detect, Off
Hi/Lo Al Detect
Set the threshold value for
high side alarm
Set the threshold value for
low side alarm
Off, Hi Al Detect,Lo Al Detect, Off
Hi/Lo Al Detect
Set the threshold value for
high side alarm
Set the threshold value for
low side alarm
Off, Hi Al Detect,Lo Al Detect, Off
Hi/Lo Al Detect
HART 7
Process Alerts Digital Output
WD
EJX
DO Select
EJX
DO Signal type
EJX
DO Test
EJX
Lo Alert Val
*1:
*2:
*3:
W
W
WD
WD
WD
W
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
<5. Parameter Summary>
Function
Label
Process Alerts Temp Hi Alert Val
Item
High alert value for temperature
Temp Lo Alert Val
Low alert value for temperature
Engr Disp
Engr Unit
User scaled value
User set engineering unit
Loop Current (DD)
AO (DTM)
Loop current value
(Analog Output Current)
Process
variables
Contents
Set the threshold value for
high side alarm
Set the threshold value for
low side alarm
5-7
Default value Handling *1
120°C (deg C)
W
-40°C (deg C)
W
R
R
Unit specified in Set Engr Unit
8 alphanumerics
3.6 to 21.6 mA
R
HART 7
Loop Current Data
Quality
Device variable process data
quality
Device variable process data
quality of Loop Current (mA)
Good
R
Device variable limit status
Device variable limit status of
Loop Current (mA)
Not limited
R
HART 7
Loop Current Limit
Status
HART 7
PV (DD)
Pres (DTM)
PV (Pres) Data
Quality
Pressure/Differential pressure
value
Device variable process data
quality
R
Device variable process data
quality of pressure
Good
R
Device variable limit status of
pressure
Not limited
R
45 ms
R
HART 7
PV (Pres) Limit
Status
Device variable limit status
HART 7
PV Update time
period (DD)
Update time period
(DTM)
PV (Pres) Update time period
HART 7
% range (DD)
Pres % (DTM)
Pressure value in %
-2.50 to 110.00%
R
Device variable process data
quality
Device variable process data
quality of % range (Percent
Range)
Good
R
Device variable limit status of
% range (Percent Range)
Not limited
R
HART 7
% rnge (Percent
Range) Data
Quality
HART 7
% rnge (Percent
Device variable limit status
Range) Limit Status
HART 7
SV (DD), SP (DTM)
SP %
SV (SP) Data
Quality
Static pressure value
Static pressure value in %
Device variable process data
quality
-10.0 to 100.00 %
Device variable process data
quality of SV (SP)
Good
RD
RD
R
HART 7
SV (SP) Limit
Status
Device variable limit status
Device variable limit status of
SV (SP)
Not limited
R
360 ms
R
HART 7
SV Update time
period (DD)
SP update time
(DTM)
SV (SP) Update time period
HART 7
*1:
*2:
*3:
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
Process
variables
<5. Parameter Summary>
Label
TV (DD)
Snsr temp (DTM)
TV (Temp) Data
Quality
5-8
Item
Temperature value
Contents
Capsule temperature
Default value Handling *1
R
Device variable process data
quality
Device variable process data
quality of TV (Temp)
Good
R
Device variable limit status
Device variable limit status of
TV (Temp)
Not limited
R
1s
R
HART 7
TV (Temp) Limit
Status
HART 7
TV Update time
period (DD)
Temp update time
(DTM)
TV (Temp) Update time period
HART 7
Range change Apply values
Min Span
LRV
LSL
URV
USL
Self test
Self test
Sensor trim
Clear P snsr trim
Clear SP snsr trim
P LTD
P LTP
P UTD
P UTP
Pres trim
Pres Zero trim
SP LTD
SP LTP
SP UTD
SP UTP
Static Pres trim
Trim Date
Trim Desc
Trim Loc
Trim Who
Set Diag Mode Set Diag Mode
Signal
characterizer
*1:
*2:
*3:
Num of points
Point setting
S.C.
X End
X Start
Y End
Y Start
Re range for measured pressure
Minimum span for pressure
Lower range value for pressure
Lower sensor limit for pressure
Upper range value for pressure
Upper sensor limit for pressure
Self-diagnostics
Reset pressure trim to factory
setting
Reset SP trim to factory setting
Lower pressure trim deviation
Lower temperature trim point
Upper pressure trim deviation
Upper temperature trim point
Pressure trim
Zeroing
Lower SP trim deviation
Lower SP trim point
Upper SP trim deviation
Upper SP trim point
Static pressure trim
Trim date
Trim description
Trim location
Trim person
ILBD operation mode
Number of coordinates
Coordinates editor
Signal characterizer permission
End point of X
Start point of X
End point of Y
Start point of Y
4 mA, 20 mA, or Exit
As specified
As specified
**/**/**
16 alphanumerics
8 alphanumerics
8 alphanumerics
Stop, Calculation, or
Reference
0 to 9
Disabled or Enabled
M
R
W
R
W
R
M
M
MD
R
R
R
R
M
M
RD
RD
RD
RD
MD
W
W
W
W
WG
9
Disabled
100.00%
0.00%
100.00%
0.00%
W
M
W
R
R
R
R
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
Function
SP setup
Label
A/G Select
Atm. Pres Value
SP Apply values
SP Damp
SP H/L Select
SP Min Span
SP LRV
SP LSL
SP URV*3
SP USL
Status
5-9
<5. Parameter Summary>
Device Status
Status group 1
Status group 2
Status group 3
Status group 4
Status group 5
Status group 6
Status group 7
Status group 8
Status group 9
Status group 10
Item
Gauge/Abs select for static
pressure
Conversion coefficient
Rerange for static pressure
Damping time constant for SP
H/L select for static pressure
Minimum span for static pressure
Lower range value for static
pressure
Lower sensor limit for static
pressure
Upper range value for static
pressure
Upper sensor limit for static
pressure
Current operating status
Device status information for
hardware
Device status information for
hardware
Device status information for
process
Device status information for
process
Device status information for
process
Device status information for data
Device status information for data
Device status information for data
Device status information for data
Device status information for data
Contents
Gauge or Absolute
Default value Handling *1
Absolute
WD
101.3 kPa
“0%, 100%, or Exit”
0.00 to 100.00
High or Low
2.00 sec
High
Within measurement range
0.0 MPa
WD
MD
WD
WD
RD
WD
RD
Within measurement range
WD
RD
Display the hardware error
R
R
Display the hardware error
R
Display the process error
(Out of specification)
Display the process error
(Out of setting range)
Display the process error
(Alarm)
Display the setting error
Display the setting error
Display the diagnostic alarm
Display the diagnostic alarm
Display the simulation mode
R
R
R
R
R
R
R
R
HART 7
Ext dev status
Extended Device Status
R
HART 7
Time Stamp
Tag
Long tag
Tag
Time Stamp
Tag number
Long tag
8 alphanumerics
Max 32 alphanumerics
00:00:00
As specified
As specified
R
W
W
Off or On
–99.999 to 99.999%/degC
Off
0.000%/degC
Linear or Sq root
As specified or
Linear
As specified or
kPa
MPa
deg C
W
W
R
R
W
HART 7
Temperature
compensation
Temperature
sensor
Transfer
function
Units
Write
protection
menu
T.Z. Cmp mode
Temp Zero
Amp temp
Snsr temp
Xfer fnctn
Temperature compensation mode
Zero shift compensation
Amplifier temperature
Capsule temperature
Output mode
Unit
Pressure, Differential pressure unit
SP Unit
Temp Unit
Enable wrt 10min
New password
Static pressure unit
Temperature unit
Write protection release
User set password for write
protection
Write protection indicator
Write protect
*1:
*2:
*3:
deg C, deg F, or Kelvin
8 alphanumerics
8 alphanumerics
Yes or No
No
W
WD
W
M
M
R
Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
Max three Burst Messages (Burst Message 1, Burst Message 2, Burst Message 3)
The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
IM 01C25T01-06EN
A1-1
<Appendix1. Safety Instrumented Systems Installation>
Appendix 1. Safety Instrumented Systems
Installation
WARNING
The contents of this appendix are cited from
exida.com safety manual on the transmitters
specifically observed for the safety transmitter
purpose. When using the transmitter for Safety
Instrumented Systems (SIS) application, the
instructions and procedures in this section must
be strictly followed in order to preserve the
transmitter for that safety level.
A1.1 Scope and Purpose
This section provides an overview of the user
responsibilities for installation and operation of
the transmitter in order to maintain the designed
safety level for Safety Instrumented Systems (SIS)
applications. Items that will be addressed are proof
testing, repair and replacement of the transmitter,
reliability data, lifetime, environmental and
application limits, and parameter settings.
A1.2 Using the transmitter for an
SIS Application
A1.2.1 Safety Accuracy
The transmitter has a specified safety accuracy
of 2%. This means that the internal component
failures are listed in the device failure rate if they will
cause an error of 2% or greater.
A1.2.2 Diagnostic Response Time
The transmitter will report an internal failure within 5
seconds of the fault occurrence.
A1.2.3 Setup
During installation the transmitter must be setup
with engineering units parameters. This is typically
done with a handheld terminal. These parameters
must be verified during the installation to insure
that the correct parameters are in the transmitter.
Engineering range parameters can be verified by
reading these parameters from the optional local
display or by checking actual calibration of the
transmitter.
The calibration of the transmitter must be performed
after parameters are set.
A1.2.4 Required Parameter Settings
The following parameters need to be set in order to
maintain the designed safety integrity.
Table A1.1
Required Parameter Settings
Item
Description
Burnout direction To specify if the output should go
switch
21.6 mA or higher or 3.6 mA or lower
upon detection of an internal failure.
Write protection The write function should be
switch
disabled.
A1.2.5 Proof Testing
The objective of proof testing is to detect failures
within the transmitter that are not detected by the
diagnostics of the transmitter. Of main concern
are undetected failures that prevent the safety
instrumented function from performing its intended
function. See table A1.2 for proof testing method.
The frequency of the proof tests (or the proof
test interval) is to be determined in the reliability
calculations for the safety instrumented functions
for which the transmitter is applied. The actual
proof tests must be performed more frequently or
as frequently as specified in the calculation in order
to maintain required safety integrity of the safety
instrumented function.
The following tests need to be specifically executed
when a proof test is performed. The results of
the proof test need to be documented and this
documentation should be part of a plant safety
management system. Failures that are detected
should be reported to Yokogawa.
The personnel performing the proof test of the
transmitter should be trained in SIS operations
including bypass procedures, transmitter
maintenance, and company management of
change procedures.
IM 01C25T01-06EN
Table A1.2
<Appendix1. Safety Instrumented Systems Installation>
A1-2
Proof Testing
Testing method
Functional test:
1. Follow all Management of Change
procedures to bypass logic solvers if
necessary.
Tools required
• Handheld terminal
Expected outcome
Remarks
Proof Test Coverage The output needs to be
=52%
monitored to assure that the
transmitter communicates
the correct signal.
• Handheld terminal
• Calibrated pressure
source
Proof Test Coverage
=99%
2. Execute HART/BRAIN command to
send value to high alarm (21.5 mA) and
verify that current has reached this level.
3. Execute HART/BRAIN command to
send value to low alarm (3.6 mA) and
verify that current has reached this level.
4. Restore logic solvers operation and
verify.
Perform three point calibration along with
the functional test listed above.
A1.2.6 Repair and Replacement
If repair is to be performed with the process online
the transmitter will need to be bypassed during the
repair. The user should setup appropriate bypass
procedures.
The development process of the transmitter is
certified up to SIL3, allowing redundant use of
the transmitter up to this Safety Integrity Level,
depending the PFDavg calculation of the entire
Safety Instrumented Function.
When replacing the transmitter, the procedure in the
installation manual should be followed.
When using the transmitter in a redundant
configuration, the use of a common cause factor
(β-factor) of 2% is suggested. (However, if the
redundant transmitters share an impulse line or if
clogging of the separate impulse lines is likely, a
common cause factor of 10% is suggested.)
The personnel performing the repair or replacement
of the transmitter should have a sufficient skill level.
Note that the failure rates of the impulse lines need
to be accounted for in the PFDavg calculation.
A1.2.7 Startup Time
A1.2.10 Lifetime Limits
The transmitter generates a valid signal within 1
second of power-on startup.
The expected lifetime of the transmitter is 50
years. The reliability data listed the FMEDA report
is only valid for this period. The failure rates of the
transmitter may increase sometime after this period.
Reliability calculations based on the data listed in
the FMEDA report for transmitter lifetimes beyond
50 years may yield results that are too optimistic,
i.e. the calculated Safety Integrity Level will not be
achieved.
In the unlikely event that the transmitter has a
failure, the failures that are detected should be
reported to Yokogawa.
A1.2.8 Firmware Update
In case firmware updates are required, they
will be performed at factory. The replacement
responsibilities are then in place. The user will not
be required to perform any firmware updates.
A1.2.9 Reliability Data
A detailed Failure Mode, Effects, and Diagnostics
Analysis (FMEDA) report is available from
Yokogawa with all failure rates and failure modes.
The transmitter is certified up to SIL2 for use
in a simplex (1oo1) configuration, depending
on the PFDavg calculation of the entire Safety
Instrumented Function.
A1.2.11 Environmental Limits
The environmental limits of the transmitter are
specified in the user’s manual IM 01C25.
A1.2.12 Application Limits
The application limits of the transmitter are specified
in the user’s manual IM 01C25. If the transmitter is
used outside of the application limits, the reliability
data listed in A1.2.9 becomes invalid.
IM 01C25T01-06EN
A1-3
<Appendix1. Safety Instrumented Systems Installation>
A1.3 Definitions and
Abbreviations
A1.3.1 Definitions
Safety
Freedom from unacceptable
risk of harm
Functional Safety
The ability of a system to carry
out the actions necessary
to achieve or to maintain a
defined safe state for the
equipment/machinery/plant/
apparatus under control of the
system
Basic Safety
The equipment must be
designed and manufactured
such that it protects against
risk of damage to persons
by electrical shock and other
hazards and against resulting
fire and explosion. The
protection must be effective
under all conditions of the
nominal operation and under
single fault condition
Verification
The demonstration for each
phase of the life-cycle that the
(output) deliverables of the
phase meet the objectives
and requirements specified by
the inputs to the phase. The
verification is usually executed
by analysis and/or testing
Validation
The demonstration that the
safety-related system(s) or
the combination of safetyrelated system(s) and external
risk reduction facilities meet,
in all respects, the Safety
Requirements Specification.
The validation is usually
executed by testing
A1.3.2 Abbreviations
FMEDA
Failure Mode, Effects and Diagnostic
Analysis
SIF
Safety Instrumented Function
SIL
Safety Integrity Level
SIS
Safety Instrumented System
SLC
Safety Lifecycle
Safety Assessment The investigation to arrive at a
judgment -based on evidenceof the safety achieved by
safety-related systems
Further definitions of terms used for safety
techniques and measures and the description of
safety related systems are given in IEC 61508-4.
IM 01C25T01-06EN
A2-1
<Appendix2. ILBD Check List>
Appendix 2. ILBD Check List
Fill out the below checklist according to the operation flow of the ILBD in order to keep the important
information for the blockage detection.
Checklist (1/5)
No.
1
Items
4-20 mA Analog Signal Setting
• Select the output mode when an alarm is
generaed.
2
Parameters
Diag Out Option
Diag Fixed Out Val
Status Output
DO Select
3
Stability of Pres
(differential pressure/pressure)
under normal condition
4
• Check that the status of Pres is “GOOD”.
• Check the maximum and minimum values of
Pres.
fDP under normal condition
5
• Check that the value of fDP is more than
7x10-10.
Start to obtain Reference values
6
• Set "Reference" to Diag Mode.
End of Reference Value Sampling
7
• Check that Diag Mode is “Calculation” after
the time set to "Diag Period" passed.
Alarm setting
• Record the status of Checkbox in Diag
Option.
Result
Off: 
Burnout: 
Fall back: 
mA
Pres:
SP:
Temp:
Diag:
All:
Status
Pres





Example



21.6 mA





Good
Max.:
Max.:12.3 kPa
Min.:
Min.:12.1 kPa
fDP


Diag Mode


Diag Mode


Diag Option
A Blocking
Large Fluct L
Large Fluct H
L Side Blocking
H Side Blocking
B Blocking
Invalid Ref F
Invalid Ref SPH
Invalid Ref SPL
Invalid Ref DP
ILBD over range






















IM 01C25T01-06EN
A2-2
<Appendix2. ILBD Check List>
Checklist (2/5)
No.
8
Items
Alarm status
• Check the alarm status shown in Diag Error.
• Check that the alarm status of “ILBD over
range” is not shown in Diag Error.
9
ILBD parameters
• Record the values of parameters for ILBD
operation.
• Check the status of parameters for ILBD
operation.
*: Record the value after checked that the
status of each parameter is “GOOD”.
Parameters
Result
Example
A Blocking


Large Fluct L


Large Fluct H


L Side Blocking


H Side Blocking


B Blocking


Invalid Ref F


Invalid Ref SPH


Invalid Ref SPL


Invalid Ref DP


ILBD over range


Diag Error
Diag Period
Lim fDPmax
Lim fDPmin
Lim fSPlmax
Lim fSPlmin
Lim fSPhmax
Lim fSPhmin
Lim BlkFmax
Lim BlkFmin
Lim DPAvgmax
Lim DPAvgmin
Diag Supp Count
Ref fDP*
Ref fSPl*
Ref fSPh*
180
3.000000
0.300000
5.000000
0.500000
5.000000
0.500000
0.600000
-0.600000
1.000000
0.050000
3
7.43245E-09
7.25765E-09
7.18374E-09
Ref DPAvg*
fDP*
fSPl*
fSPh*
BlkF*
DPAvg*
5.36425E+00
7.48562E-09
7.23277E-09
7.14085E-09
-0.287259
0.055957
IM 01C25T01-06EN
A2-3
<Appendix2. ILBD Check List>
Checklist (3/5)
Go to the following step according to the result of "Invalid Ref xx" shown in the Diag Error of 8th check item.
Invalid Ref SPH

Diag Error
Invalid Ref SPL

Invalid Ref DP




→
→
Check
item
10-a
10-b
: The alarm is generated.
: The alarm is not generated.
No.
10-a
Items
Simulation of Blockage detection operation
• H Side Blocking: 10-a-1
• L Side Blocking: 10-a-2
• Both Side Blocking: 10-a-3
10-a-1 H Side Blocking
• Close the high-pressure side valve
completely.
• Record the values of fDP, fSPl, fSPh, BlkF,
and DPAvg after the certain time,
(Diag Period X Diag Supp Count), passed.
*: Record the value after checked that the
status is “GOOD”.
• Record the status of Checkbox in Diag
Option.
• Check that the alarms status of “A Blocking”
and “H Side Blocking” are set.
Note: If the alarm of “ILBD over range” is generated,
the valve may be closed too much tightly. Open
valve a little and record the updated status of the
parameters.
• Check that the alarm of “H Side Blocking” is
generated.
• Check that the alarm of “L Side Blocking” is
not generated.
Parameters
Result
Example
fDP*
7.48562E-09
fSPI*
7.23277E-09
fSPh*
7.14085E-09
BlkF
-0.287259
Diag Option
A Blocking


Large Fluct L


Large Fluct H


L Side Blocking


H Side Blocking


B Blocking


Invalid Ref F


Invalid Ref SPH


Invalid Ref SPL


Invalid Ref DP


ILBD over range


L Side Blocking


H Side Blocking


Diag Error
IM 01C25T01-06EN
A2-4
<Appendix2. ILBD Check List>
Checklist (4/5)
No.
Items
10-a-2 L Side Blocking
• Close the low-pressure side valve completely.
• Record the values of fDP, fSPl, fSPh, BlkF,
and DPAvg after the certain time,
(Diag Period X Diag Supp Count), passed.
*: Record the value after checked that the
status is “GOOD”.
• Record the status of Checkbox in Diag
Option.
• Check that the alarms status of “A Blocking”
and “L Side Blocking” are set.
Note: If the alarm of “ILBD over range” is generated,
the valve may be closed too much tightly. Open
valve a little and record the updated status of the
parameters.
• Check that the alarm of “L Side Blocking” is
generated.
• Check that the alarm of “H Side Blocking” is
not generated.
10-a-3 Both Side Blocking
• Close the both-pressure side valves
completely.
• Record the values of fDP, fSPl, fSPh, BlkF,
and DPAvg after the certain time,
(Diag Period X Diag Supp Count), passed.
*: Record the value after checked that the
status is “GOOD”.
• Record the status of Checkbox in Diag
Option.
• Check that the alarms status of “H Side
Blocking”, “L Side Blocking”, and “B Blocking”
are set.
Note: If the alarm of “ILBD over range” is generated,
the valve may be closed too much tightly. Open
valve a little and record the updated status of the
parameters.
• Check that the alarm of “B Blocking” is
generated.
Parameters
Result
Example
fDP*
7.48562E-09
fSPI*
7.23277E-09
fSPh*
7.14085E-09
BIkF
-0.287259
Diag Option
A Blocking


Large Fluct L


Large Fluct H


L Side Blocking


H Side Blocking


B Blocking


Invalid Ref F


Invalid Ref SPH


Invalid Ref SPL


Invalid Ref DP


ILBD over range


L Side Blocking


H Side Blocking


Diag Error
fDP*
7.48562E-09
fSPI*
7.23277E-09
fSPh*
7.14085E-09
BIkF
-0.287259
Diag Option
A Blocking


Large Fluct L


Large Fluct H


L Side Blocking


H Side Blocking


B Blocking


Invalid Ref F


Invalid Ref SPH


Invalid Ref SPL


Invalid Ref DP


ILBD over range


Diag Error
B Blocking


IM 01C25T01-06EN
A2-5
<Appendix2. ILBD Check List>
Checklist (5/5)
No.
10-b
Items
Simulation of Blockage detection operation
• Close completely the valve for the side where
the alarm of Invalid Reference Value is not
generated.
For the case that the high-pressure side value is
closed;
Parameters
Result
Example
fDP*
7.48562E-09
fSPh*
7.14085E-09
fDP*
7.48562E-09
fSPI*
7.23277E-09
• Record the values of fDP, fSPl, fSPh, BlkF,
and DPAvg after the certain time,
(Diag Period X Diag Supp Count), passed.
*: Record the value after checked that the
status is “GOOD”.
For the case that the low-pressure side value is
closed;
• Record the values of fDP, fSPl, fSPh, BlkF,
and DPAvg after the certain time,
(Diag Period X Diag Supp Count), passed.
*: Record the value after checked that the
status is “GOOD”.
• Record the status of Checkbox in Diag
Diag Option
Option.
A Blocking
• Check that the alarms status of “B Blocking” is
Large Fluct L
set.
Large Fluct H
Note: If the alarm of “ILBD over range” is generated,
the valve may be closed too much tightly. Open
valve a little and record the updated status of the
parameters.
• Check that the alarm of “B Blocking” is not
generated.






L Side Blocking


H Side Blocking


B Blocking


Invalid Ref F


Invalid Ref SPH


Invalid Ref SPL


Invalid Ref DP


ILBD over range




Diag Error
B Blocking
IM 01C25T01-06EN
i
Revision Information
 Title
:
 Manual No. :
DPharp
HART 5/7 Communication Type
(EJXA, EJAE)
IM 01C25T01-06EN
Edition
Date
Page
1st
June 2010
—
2nd
Apr. 2012
—
2-1
3-34
3rd
June 2012
—
Revised Item
New publication
Re-edit to a common User’s Manual of HART 5 and HART 7.
2.1
Add integral indicator display when powering on.
3.3.18 Add switching procedure for HART protocol revision
(HART 5/HART 7)
Add EJA series
IM 01C25T01-06EN
Download PDF