Spectra Flood 24T9
24 x 9W tri-colour LEDs (RGB)
User Manual
Convection
cooled,
no fan!
Order code: LEDJ280
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modifications to this equipment are not subject to warranty.
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modification to the equipment.
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Do not expose to flammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available voltage is between
100~240V, 50/60Hz.
• Make sure that the power cable is never crimped or damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualified
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature fluctuation (e.g. after transportation), do not connect power or switch it on immediately. The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualified technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• WARRANTY: One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
www.prolight.co.uk
Spectra Flood 24T9 User Manual
2
Product overview & technical specifications
Spectra Flood 24T9
The Spectra Flood 24T9 is a high output, tri-colour architectural fixture suitable for events, rental or installation. Housing 24 x 9W RGB tri-colour LEDs the Spectra Flood 24T9 is suitable for lighting large buildings, structures and gardens. The immense colour palette can transform environments using the fixture’s incredible long throw capability.
•24 x 9W tri-colour LEDs (RGB)
•Beam angle: 45°
•4.2kHz refresh rate
•IP66 rated
•DMX channels: 1/3/4 or 6 selectable
•Static colour, colour change, colour fade, auto run,
sound active and master/slave modes
•0 - 100% dimming with variable strobe
•Bracket allows for floor standing applications
•4 push button menu with LED display
•IP rated power in/out
•IP rated DMX in/out
•Convection cooled
•Adjustable tilt angle
•Large carry handles
NOTE: The fixture may be installed by removing the rubber feet and securing using four or more fixing holes in the base.
45° - Lux
16290
4843
2073
1242
815
45°
0m
1m
2m
3m
4m
5m
Specifications
Spectra Flood 24T9
Power consumption
230W
Power supply
100~240V, 50/60Hz
Dimensions
425 x 570 x 264mm
Weight
15.7kg
Order code
LEDJ280
570mm
264mm
425mm
www.prolight.co.uk
Spectra Flood 24T9 User Manual
3
Technical specifications
01
03
03
05
06
02
02
03
03
07
08
09
10
04
01 - Bracket
02 - Bracket tightening knobs
03 - Carry handles
04 - Earth point
www.prolight.co.uk
05 - LED display
06 - Function buttons
07 - DMX input socket
08 - DMX output socket
09 - Power in socket
10 - Power out socket
In the box: 1 x fixture,
1 x power cable &
1 x user manual
Spectra Flood 24T9 User Manual
4
Operating instructions
DMX channel mode:
Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show. In this mode you will be able to control each individual trait of the fixture
and each fixture independently.
To access the DMX channel mode, press the “MODE” button on the rear of the unit to show d001 on the LED display. Now use the “UP” and “DOWN” buttons to set the desired DMX address. Now press
the “ENTER” button to choose one of the 1, 3, 4 or 6 DMX channel modes, press the “ENTER” button to
confirm the setting.
To exit out of any of the above options, press the “MODE” button.
1 channel mode:
3 channel mode:
Channel Value
Function
Channel Value
1
No function
1
000-255 Red (0-100%)
001-022 Red
2
000-255 Green (0-100%)
023-045 Green
3
000-255 Blue (0-100%)
000
046-068 Blue
069-091 Cyan
4 channel mode:
092-114 Yellow
Channel Value
115-137
Orange
Function
Function
1
000-255 Red (0-100%)
138-160 Pink
2
000-255 Green (0-100%)
161-183 Purple
3
000-255 Blue (0-100%)
184-206 Dark blue
4
000-255 Master dimmer (0-100%)
207-229 Pale green
230-252 White
253-255 Warm white
www.prolight.co.uk
Spectra Flood 24T9 User Manual
5
Operating instructions
6 channel mode:
Channel
Value
Function
1
000-255
Master dimmer (0-100%)
2
000-255
Red (0-100%) when channel 6 is 000
000-008 Red
009-017
Orange
018-026 Yellow
027-035 Spring Yellow
036-044 Light Yellow
045-053 Lime
054-062 Light Green
063-071
Green
072-080 Pastel Green
081-089 Light Cyan
090-098 Cyan
099-107 Light Blue
108-116 Medium Blue
117-125 Blue
126-134 Violet
Static colours can be used
when channel 6 is 001-025
135-143 Purple
144-152 Magenta
153-161
Pink
162-170
Light Pink
171-179
Pastel Blue
180-188 Pastel Green
189-197 Pastel Yellow
198-206 Pastel Purple
207-215
Pastel Cyan
216-224
Turquoise
225-233 Pastel Pink
234-242 White
243-251
Warm White
252-255 Cool White
000-255
www.prolight.co.uk
Program speed (slow-fast) when channel 6 is 026-255
Spectra Flood 24T9 User Manual
6
6 channel mode continued:
3
000-255 Green (0-100%)
4
000-255 Blue (0-100%)
5
000-009 No function
010-255 Strobe (slow-fast)
6
000
No function
001-025 Program 1 - Static colour
(see channel 2)
026-051 Program 2 - 7 colour fade
052-077 Program 3 - 3 colour fade
078-103 Program 4 - 7 colour
change
104-129 Program 5 - 3 colour
change
130-155 Program 6 - Dynamic colour fade 1
156-181 Program 7 - Dynamic colour fade 2
182-207 Program 8 - Red continous fade
208-233 Program 9 - Green continous fade
234-255 Program 10 - Blue continous fade
www.prolight.co.uk
Spectra Flood 24T9 User Manual
7
Operating instructions
Built-in program mode:
To access the built-in program mode press “MODE” until the display shows Pr.01 on the LED display. Press “ENTER” to confirm the setting. Use the “UP” and “DOWN” buttons to select a program from Pr.01 ~ Pr.10. Press the “ENTER” button to confirm the setting.
To change the speed of the selected program press the “ENTER” button and then use the “UP” and
“DOWN” buttons to select any value from SP00 ~ SP99. Press the “ENTER” button to confirm the
setting, then use the “UP” and “DOWN” buttons to select and value from F500 ~ F599 for the
strobe feature. Press the “ENTER” button to confirm the setting.
In Pr.01 you are able to set a specific static colour. When in Pr.01 press the “ENTER” button and
then use the “UP” and “DOWN” buttons to go through the static colours. Press the “ENTER” button to
confirm the setting, then use the “UP” and “DOWN” buttons to select and value from F500 ~ F599
for the strobe feature. Press the “ENTER” button to confirm the setting.
To exit out of any of the above options, press the “MODE” button.
Programs:
Static colours:
Pr.01
Static colour
Pr.06
Dynamic colour fade 1
1.--r - Red
5.--b - Blue
Pr.02
7 colour fade
Pr.07
Dynamic colour fade 2
2.-rg - Yellow
6.-rb - Pink
Pr.03
3 colour fade
Pr.08
Red continous fade
3.--g - Green
7.rgb - White
Pr.04
7 colour change
Pr.09
Green continous fade
4.-gb - Cyan
8.off - Blackout
Pr.05
3 colour change
Pr.10
Blue continous fade
Master/slave mode:
To set the master unit, press the “MODE” button on the rear of the master unit then select your desired
program (sound active, auto, static colour or one of the built-in programs). To set the other units in slave
mode, press the “MODE” button on the rear of the unit to show SLAU on the LED display and press
the “ENTER” button to confirm the setting. The units will now run in sequence with the master unit.
To exit out of any of the above options, press the “MODE” button.
Menu system
Please ensure that all slave units are set to the same DMX channel mode as the master unit.
Built-in program
Pr.01 Static colour
Pr.02 7 colour fade
Pr.03 3 colour fade
Pr.04 7 colour change
Pr.05 3 colour change
Pr.06 Dynamic colour fade 1
Pr.07 Dynamic colour fade 2
Pr.08 Red continous fade
Pr.09 Green continous fade
Pr.10 Blue continous fade
SP00~SP99 (speed)
F500~F599 (flash)
Auto mode
AUTO
Slave mode
SLAV
DMX mode
1CH, 3CH, 4CH, 6CH
Address setting
A001~A512
Auto mode:
To access the auto mode press “ENTER” until the display shows Auto on the LED display. The fixture will now run through its built in programs Pr.02 ~ Pr.10. To exit out of any of the above options, press the “MODE” button. NOTE: The user can set up the speed and flash speed for Pr.02 ~ Pr.10 under the built in programs mode. Changing this here will then take effect when running auto mode.
www.prolight.co.uk
Spectra Flood 24T9 User Manual
8
DMX setup
Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start address”
from 1- 512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was
addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105
and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the
chain starts at 107.
DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent
fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture.
DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a data “out” terminal).
DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
DATA cable (DMX cable) requirements (for DMX operation):
This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.
Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers.
Please quote:
LEDJ 1m Interior Exterior DMX cable
LEDJ 1m Exterior DMX cable
LEDJ 2m Exterior DMX cable
LEDJ 5m Exterior DMX cable
LEDJ 10m Exterior DMX cable
Order code: LEDJ91
Order code: LEDJ141
Order code: LEDJ142
Order code: LEDJ143
Order code: LEDJ144
LEDJ 1m Exterior Power cable
LEDJ 2m Exterior Power cable
LEDJ 5m Exterior Power cable
LEDJ 10m Exterior Power cable
Order code: LEDJ146
Order code: LEDJ147
Order code: LEDJ148
Order code: LEDJ149
Also remember
that DMX cable
must be daisy
chained and
cannot be split.
www.prolight.co.uk
Spectra Flood 24T9 User Manual
9
DMX setup
Notice:
Be sure to follow the diagrams below when making your own cables. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special note:
Line termination:
When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
Termination reduces signal transmission
problems and interferance. it is always
advisable to connect a DMX terminal,
(resistance 120 Ohm 1/4 W) between pin 2
(DMX-) and pin 3 (DMX+) of the last fixture.
5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a
3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
www.prolight.co.uk
Spectra Flood 24T9 User Manual
10
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
www.prolight.co.uk
Spectra Flood 24T9 User Manual
11
www.prolight.co.uk
Spectra Flood 24T9 User Manual
12
Download PDF