RAVE Water Sports Equipment User Manual

Operator’s Manual
1. This tube is designed to carry no more than two persons
or 340 lbs.
2. Use a tow rope of at least 2,375 lbs. average tensile
strength for pulling this tube and its riders.
3. Read Owner’s Manual before use. Do not remove
Product Instructions and Warnings
To reduce the risk of injury or death using this tube, follow these
• Carefully read this manual and follow the instructions.
• Only use your tube with a responsible watercraft
operator who knows how to operate a watercraft
• Take all reasonable precautions in the use and operation
of your tube and boat.
Product Instructions and Warnings (continued)
• Teach anyone using your tube how to attach it to the
rope, how to ride it and how to maintain it.
• Do not exceed the manufacturer’s recommended
number of riders for your particular tube
• If the tube is designed for more than one person, take
extra precaution to avoid colliding with one another.
• Never strap or attach anyone to the tube or cover. Never
put your feet or hands through the strapping of the
towing system or handles. Never wedge your hands or
feet under the cover or between the cover and the tube.
• Never attempt jumps or dangerous tricks with your tube.
If more than one tube is being towed, avoid collisions
with other tubes.
• Scout the area before use to avoid any debris or
obstacles that might present a safety hazard.
• Know your own limits. Stop when you are tired. Act
responsibly. Be in good physical condition and cautious
in your use of this or any other towable tube.
• Check the rope and connectors for frays, cuts, sharp
edges, knots, or wear before each use. Discard rope if
any such condition exists or if rope appears to be worn.
Such conditions may lead to breaks
• Do not use tow rope with elastic or bungee material to
pull riders. Such an addition can break or stretch, which
may lead to injury of users or boat occupants.
• The stress on the rope is different than the stress on the
tube, and will vary with the weight of the riders, design
and surface area of the tube.
• Rope is subject to deterioration when exposed to direct
sunlight. The life of the product will be extended when
stored away from sunlight.
• The tow rope should be replaced when signs of
deterioration appear, indicated by the existence of
discoloration, wear, fraying or unraveling.
• Do not add hardware or attachments that are not
otherwise supplied by the manufacturer.
Do not use at speeds that exceed the skill of the
rider. Boat speed should never exceed 20 mph for
adults and 15 mph for children.
This product should never be used by children except
under adult supervision.
This is not a personal flotation device.
Always wear a U.S. Coast Guard approved Type III
(PFD) vest.
Never place wrists or feet through handles or towing
harness. Ensure tow rope is clear of all body parts
prior to or during use.
Rider should keep feet out of the water.
Watercraft driver is responsible for the ride since the
tube cannot be controlled by the rider.
Always have a person other than the driver observing
the rider.
Watercraft driver should avoid excessive speed or
sharp turns which might cause the tube to flip over
abruptly, resulting in serious injury to the rider.
 Do not tow in shallow water or near shore, docks,
pilings, swimmers or other boats.
 Do not exceed the manufacturer’s recommended
number of riders for your particular tube.
 Use a tow rope of at least 1,500 lbs. average tensile
strength for pulling a single person; 2,375 lbs.
average tensile strength for pulling two people; 3,350
lbs. average tensile strength for pulling three people;
and 4,100 lbs. average tensile strength for pulling
four people on an inflatable tube. The tow rope
should be at least 50 feet in length but not to exceed
65 feet.
 Do not operate watercraft or ride under the
influence of alcohol or drugs.
 Read Operator’s Manual before use.
Your equipment and your tow rope:
• Inspect all equipment prior to use. Check tube and
attachment point prior to each use. Do not use if
• Always wear a U.S. Guard Type III (PFD) vest.
• Rope should be attached to the watercraft in an approved
fashion with hardware designed for pulling. Refer to your
watercraft manual for instructions on proper tow rope
• Tow ropes stretch during use. If a rope breaks or is
suddenly released, it can snap back into the watercraft.
Warn all riders and occupants of the danger of the rope
• When in the boat, keep away from the tow rope to avoid
injury. Passengers can be hit or become entangled in the
• Inspect tow rope and its attachments before using. Do not
use tow rope if frayed, knotted or damaged. Replace when
signs of excessive deterioration are indicated by
discoloration, broken filaments, unraveling or other
obvious signs of wear on the rope or hardware.
• Use proper tow rope for the activity.
• Ensure rope is clear of all body parts prior to starting out
or during use.
• Keep persons and ropes away from propeller when engine
is running, even in neutral. Should rope become entangled
When You Ride:
• Attempting land or dock starts can increase the risk of
• Always remove any slack in the rope between watercraft
and rider before starting. Sudden shock loads may cause
injury to the rider or failure of rope, resulting in snap-back
or breakage.
• Do not ride in shallow water, near shore, pilings, docks,
rafts, swimmers, other boats or other obstacles. Such
obstacles are examples of risks that are inherent in the
• The driver and rider must watch for and be able to stop or
turn to avoid obstacles.
• Always ride in control and at speeds appropriate for your
ability. Ride within your limits. Follow instructions on tube
for safe speed limits.
• Do not ride over ramps or jumps.
• Falling and the injuries that may result are inherent risks
in the sport.
• Use a flag to signal to others that a rider is in the water.
• Driver must use extra caution approaching fallen rider and
keep eye contact on fallen rider at all times.
• Put the boat in neutral when near a fallen rider. Turn the
engine off when people are getting in or out of the boat, or
while in the water near the boat.
Do not operate watercraft or ride under the influence of alcohol
of drugs.
Inflating Instructions
CAUTION: DO NOT OVER-INFLATE. Use of an air compressor or overinflation can rupture the tube beyond repair, thus voiding the
warranty. Use extreme care if using compressed air to fill the tube.
Step 1
Lay the RAZOR on a flat surface. Make sure there are no sharp
objects under the product that might puncture the tube.
Step 2
Open the zipper in the cover and inflate the safety bladder. Make
sure the valve plug is fully seated and pushed in so it is flush
with the surface of the tube. Close the zipper and fasten the
Velcro flap over the top of the zipper pull.
Step 3
Remove outer valve body from repair kit bag. Locate the Boston
valve underneath the square flap on the top of the cover
towards the rear of the tube. Screw in the outer valve body and
remove cap. Inflate using a hand pump or powered inflator until
it is firm and the cover is taut. Check cover positioning during
inflation and adjust if necessary. Install valve cap, ensuring it is
seated squarely and fully.
Note: A firm and fully inflated tube will perform better on the
water than an under-inflated tube and is less subject to damage.
Use a hand pump to top off, if needed, to obtain this firmness.
However, do not over-inflate. Inflate only until firm.
Note also that the air pressure in the tube will fluctuate
depending on air and water temperatures. Adjust the air
pressure in the tube accordingly throughout the day to maintain
proper firmness during use.
Step 4
Attach a properly rated tow rope (not
Important: Loop end of rope MUST pass
through hole of the quick-connect prior to
wrapping loop around hooks. Inspect
condition of molded tow point prior to
each use. Do not use if it shows signs of
damage, cracking or breaking.
To Deflate:
• Unscrew entire valve body from base.
Air chamber won’t hold air:
• Check main Boston valve to ensure plastic ring is not caught
under the seal or cap.
• Check for holes in bladder following the procedures in the
“Repair” section.
Cleaning and Storage
• When the inflatable product is not being used, we
recommend that you store it in a covered, shaded area. This
will help protect it against ultraviolet (UV) rays and extend
the life of the product.
• Clean the inflatable completely with a mild soap and fresh
• Product should be completely dry and remain dry while
• Roll the product loosely and place in a vented storage bag
or container.
• Store in a cool, dry location. Do not store product directly
on concrete surface. Place mothballs around stored
inflatable to keep mice and insects away.
• Secure the product to prevent unauthorized or
unsupervised use.
For Minor Holes or Tears:
• Remove the inner bladder from the cover.
• Inflate the tube and locate the leak by spraying the tube
with soapy water. Bubbles will appear where there is a leak.
• Determine the hole size and cut a circular patch ½ - 1 inch
wider than the hole.
• Remove air from the tube and dry tube completely where
the patch is to be applied.
• Peel off paper back from patch, apply repair patch to area
and work out any air bubbles from beneath the patch.
• Apply weight to the patched area for one hour before reinflating.
• Put the bladder back into the cover.
NOTE: Ensure the outer edge seam of the bladder is aligned
with the cover seam and is spread out evenly within the cover.
A misaligned cover can cause distortion and less than optimal
performance of the tube.
RAVE Sports Raft
Water Sports
Download PDF