Advertisement
Advertisement
USER MANUAL
Please read this manual carefully before use
Please keep this manual for future reference
ROHS
CONTENTS
1. INTRODUCTION AND SAFETY 1
2. PRESENTATION 3
3. INSTALLATION 6
4. CONTROL PANEL AND REMOTE CONTROL 10
5. USE 11
6. MAINTENANCE AND STORAGE 15
7.TROUBLE SHOOTING 16
8. EXPLODED VIEW 18
1. INTRODUCTION AND SAFETY
1 2
4 5 6
7 8 9
0
1.1 Introduction
The product official representative in Latvia is
Smartrobby, SIA www.smartrobby.com
Dzirciema iela 119-B, Rīga, LV-1055
Tel.: +371 26680333
Thank you for purchasing our product.
You will have and enjoy the extra free time while using our robot lawn mower to mow your lawn. You will be impressed with your lawn's appearance and best of all, Tianchen robot did it for you.
1. WARNING-this is a dangerous power tool. Use care when operating and follow all safety instructions and warnings.
2. Read the owners/operating manual carefully and follow all safety instructions
before operating the machine.
3. Objects can be thrown from mower while operating, keep a safe distance from the
machine when operating, take caution.
4. Keep children, pets and bystanders away from mower when operating.
5. WARNING-Operate the disabling device before working on or lifting the machine.
6. Never use a high-pressure washer or even running water to clean the mower.
7. Sharp rotating blades. Keep hands and feet away and do not attempt to lift mower from this area.
8. WARNING-Do not ride on the machine.
The robot mower may be used only by those who know how to operate it after reading and understanding the instructions in this manual.
Model: TC-158N
CE, RoHs approved.
2. Handle
Carry the mower by the handle at the rear under the mower. Carry the mower with the blade device away from the body.
Product, product specifications and this document are subject to change without notice. All other trademarks are property of their respective owners.
WARNING
Severe injury or death may cause if incorrectly lift the mower.
IMPORTANT!
The following pages contain important safety and operating instructions. Please read and follow all instructions in this manual. Carefully read and review all safety instructions, warnings and cautions contained in this manual.
3. Specifications symbol
Failure to read and follow these instructions, warnings and cautions statements may result in severe injury or
death to persons and pets or damage to personal property. It’s not permitted to modify the original design of robot. All modifications are made at your own risk.
SIA “Smartrobby”
Product name: Robot lawn mower
Model: TC-158N I P54
Input: 24 V 2A 82 W
Made in China
S.N.:XXXXXXXXXXX158N
R O HS
Pasted on mower
SIA “Smartrobby”
Product name: Robot lawn mower
Model: TC-158N I P54
Input: 24 V 2A
Ouput 24 V 2A
Made in China
Address:XX
R
O
HS
Pasted on charging station
ADDRESS: XX
Enter XX to mower, in order to match the communication
between charging station and robot lawn mower.
WARNING
Robot lawn mower can be dangerous if incorrectly used!
S.N.: XXXX XX XX XXX
year
month date number
: Waste electrical products should not be disposed
of as household waste. Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
IMPORTANT INFORMATION
Read through the Operators Manual carefully and understand the content before using your Robot
.
4. Charging station symbol.
CAUTION!
Position this side of the Charging Station towards lawn interior.
1.2 Symbols on Mower
These symbols can be found in the mower. Study them carefully so you understand their significance.
1. The symbol is pasted on the top cover,
Please read the means carefully before use
the appliance.
This label is pasted on charging station, please make sure to position this side towards lawn interior. Failure to do may result in damage to property or persons.
- 1 -
5. Warning symbol.
DANGER! Sharp rotating
blade. Keep hands and feet
away. Serious
injury can
occur.
1. INTRODUCTION AND SAFETY
- Always turn off the power before lifting the mower or attempting any adjustment.
DANGER
- Do not operate the mower on slopes greater than 30 degrees or use it in manual operation on slopes where a firm footing is not possible.
1.3 Symbols in the User Manual
These symbols can be found in this user manual.
WARNING xxxxxxxxxxxxxxxxxxxxxxxxx.
A warning box indicates a risk of personal injury exist.
- Do not operate the mower if any safety feature or
device is damaged or inoperable.
- Do not attempt to disable or defeat any safety feature
or device.
- Use heavy gloves when inspecting or servicing the
blades.
- Wear eye protection and use gloves when installing the virtual wire and driving the wire stakes/pegs. Firmly drive all pegs in order to keep the wire from becoming
a tripping hazard.
IMPORTANT INFORMATION
- Do not use the charging station power supply with an
extension cord.
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx.
- Use only the original equipment power pack and power
supply/charger with this mower.
An information box indicates a risk of material damage exist, especially when the stated instructions are not followed. The box is also used where there is a risk of user error.
- Do not use the power supply/charger if the cord has
become damaged.
1.4 Safety instructions
- Read the owners/operation manual carefully and follow all the safety and warning instructions.
- Do not place metal objects in the area of the charging
sheets on the charging station.
- Do not place metal objects across the charging heads
of the mower.
- This machine has sharp rotation blades! Never allow the mower to operate unattended; keep bystanders, children and pets away from mower when in operation.
- Do no spray water directly into the docking area of the charging station or onto the control panel on the charging station.
- Never allow anyone to ride or sit on mower.
- The mower has sharp rotating blades! Please care the mower when it is mowing, in case of serious injury occur.
- Never allow anyone or person who is not familiar with the safe operation of the mower to operate the mower.
- Keep the lawn mower in perfect operating conditions by performing the maintenance procedures outlined by the manufacturer. Good maintenance guarantees
better performance and longer service life.
- Keep hands and feet away from the cutting blades
and other moving parts.
- Never attempt to service or adjust the mower while it
is in operation.
- Inspect and clear the mowing area of all debris (toys, tree branches, items of clothing, anything with a height less than 6cm) before operating the mower.
- In order not to irreversibly damage electric and electronic parts, do not wash the robot with water jets
at a high pressure and do not plunge it partially or
thoroughly in water, as it is not watertight.
- It is absolutely forbidden to use the robot in explosive
and flammable environments.
- Never raise the mower or attempt to inspect the blades while the mower is operating.
- The operator or user is responsible for accidents or hazards occurring to other people or their property.
- When operating the mower in manual mode, maintain a safe distance from behind or around the mower and wear proper foot apparel.
- 2 -
- Fill up all small holes and even all small mounds inside working area. It’s to keep the robot with perfect operating.
2. PRESENTATION
2. PRESENTATION
This chapter contains information you should be aware of before placing the installation.
2.1 What’s in box
8
1 1 2 1
3 4 5
6 7
10 11 12
15
22 23 24
16
17
18
19
21
20
1 Bumper:
To change a new direction when it bumps obstacles.
2
3
Charging head:
For recharging.
Emergency switch
4 Charging terminal
5 Rain sensors
6 Power light
7 Key switch
8 Control panel and LCD display
Safety hence:
To keep off feet and hands
10 Blade shield
11 Handle
Please always lift the robot by handle
12 Rear running wheel
13 Blade
14 Front wheel
15 Home button
16 Charging light
Red: Charging
Green: full recharged / idle
17 Virtual wire light
Colorless: in good connecting
Red: broken wire / idle
28 29
18 Charging terminal
19 Virtual wire terminal
20 Charging sheets
21 Hole for stake
22
23
Charger
Virtual wire (100m):
Used to mark mowing area and create a virtual wall for the mower.
24 Virtual wire connectors (10pcs):
Used to connect virtual wire.
25 Pegs (100pcs):
Used to fix the virtual wire to the ground around the lawn perimeter and around obstacles.
26 Stakes (4pcs):
Used to fix the charging station to the ground.
27 Remote control (1pc)
28 Remote control battery (2pcs)
29 Blade for replacement (2pcs)
30
Inner hexagon spanner (1pc)
31 Keys (2pcs)
32 English user manual
30
- 3 -
25 26
31
27
32
Consumable parts:
1. Blade
2. Virtual wire
3. Virtual wire connectors
4. Pegs
5. Stakes
6. Remote control battery
7. Inner hexagon spanner
8. Rear running wheels
9. Front wheels
14
13
2. PRESENTATION
2.2 Function of S510
- Lift sensor
There are lift sensors located on the front wheels. If the mower is lifted from ground, it will stops working within
1 second.
- Tilt sensor
There are tilt sensors installed on the mower too, when
the mower is tilted over 30 degrees in any direction, it stops working within 2 seconds.
- Bump sensors
There are bump sensors equipped at the front of mower.
they will activate when the mower strikes solid, fixed
object when that object is at least 6cm in vertical height
from the supporting surface of the mower. When the
bump sensor activated, the mower will stop movement in that direction and reverse itself away from the obstacle.
- Virtual wire
The robot lawn mower can't be operated without a virtual wire. (we suggest to use 100m-600m of virtual wire). The mower will follow virtual wire to charging station, the virtual
wire acts as a virtual fence. It will get on the virtual wire
until it meets charging sheets, then it gets off from virtual
wire and starts cutting inside.
LINE (virtual wire) can be selected ON/OFF from control panel.
- Mower stops working if virtual wire is cut off or charging station is power off.
If virtual wire is cut or broken, or the charging station loose power, the mower will stop working within 3 seconds.
- Rain sensors
There are two rain sensors located on the top cover. The mower will go back to the charging station automatically
when it's raining.
Rain sensors can be selected ON/OFF from control panel.
Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.
- Wireless remote controller
- Mowing schedule
Set up one week (From Monday to Sunday, once for each day) cutting schedule from control panel. This function should be used together with AREA function.
- Anti-theft function
Mower has password option and key protection to guard against theft. What's more, the mower can not be turned on without a charging station.
- Two cutting modes
There are two cutting modes of the mower, go straight and go circle (high efficiency).
In Auto, mower selects cutting mode intelligently.
It goes straight if the grass is sparse or it has be cut off, and it goes circle if the grass is dense or long.
In manual mode, the mower will just go were you direct it.
- Four steps to safely start the mower
There are four necessary steps to start the mower:
1. Connect charging station with power supply by charger
and make sure the recharging light is in green color.
2. Connect virtual wire to charging station and make sure
it is in good connecting(virtual wire light in colorless).
3. Turn on the key switch and release the emergency
switch.
4. Input password if selected and select mode.
- Overload protect
Each of the cutting motors the two running motors are
monitored continuously during operation for any situation that may cause these motors to over-load in the event
this is detected, the mower stops operating.
- Cutting width: 28cm
- Easy cutting height adjustments
Two levels of cutting blades, one level is 3cm, another
is 4cm. Change blades to adjust the cutting height.
- Auto recharge system
When the mower senses a low battery situation, it will shut off the cutting motors and search for the virtual wire.
Once found it will follow the virtual wire to the charging station for recharge automatically. Once charging is
complete, the mower will back up a few centimeters
ready to go again in stand by mode.
- Waterproof
Waterproof design, there is an inner cover under top cover which protect inside parts from humidify.
- LCD display
- Electronic compass
The mower has compass navigation system to keep it going straight on inclines.
- Emergency stop switch
There is an emergency switch located on the top of mower and red in color. When pressed, the mower will
shut down immediately. Rotate the switch clockwise to
release it.
- Subarea setting
You can select Subareas for the mower to cut. This works well for large lawn. See Section 5.11.
This function should be used together with schedule.
- Different languages selection.
- 4 -
2. PRESENTATION
2.3 Technical date
Model No.
Mower technical date
Gross weight
Net weight
Mower size
Rated power
Noise
Qty for cutting blades
Cutting height
Cutting width
Cutting speed
Blades rotate speed
Hill capability
Max ambient functioning temp.
Coverage(for once charging)
Working capacity
Warranty
40℃
TC-158N
18/21KGS
15/18KGS
56*51*25cm(LWH)
82W
≤65db
2pcs
3cm/4cm
28cm
20m/min
4000rpm±10%
30degree Max slope
600m2+20％
1500m2+20％
1 year
Note:
How large an area is mow per recharged depends
primarily on the condition of the blade and the type of grass, growth rate and humidity. The shape of garden is also significant. If the garden mainly consists of open lawns, mower can mow more area per hour than if the
garden consists of several small lawns separated by
trees, flower beds and passages.
Charging station and virtual wire
Charging station size 45*38.5*23.5cm(LWH)
Virtual wire maximum length
Standard virtual wire length
600m/0.5mm
100m/0.5mm
Wireless remote control distance 6M
Battery
Type of battery
Battery capacity
Charging time
Average working time
Functions:
Follow virtual wire walking is optional
Mower is disabled without power to charging station
Mower is disabled if virtual wire is cut or broken
Pressure sensor
Rain sensor
Auto recharge
Intelligent spiraling
Go straight
Anti theft
Lift sensor
Tilt sensor
Ultrasonic sensor
Bumper sensor
LCD display
Waterproof
Touch sensor
Time set-up system
Emergency switch
Password set-up
Electronic compass
Language option
Subarea setting
Lithium/Lead-acid
6.6Ah/7.2Ah
≤3hours
2-3hours
X
X
X
2.4 Working route
- 5 -
3. INSTALLATION
3. INSTALLATION
This chapter describes how you to install this mower.
Before starting the installation, read the previous chapter 2. Presentation.
Read the whole of this chapter before starting the installation. How the installation is made also affects
how well the mower will work. It is therefore important
to plan the installation carefully.
3.1 Preparations
Training
- Read the instructions carefully. Be familiar with the controls and the proper use of the mower.
- Never allow people unfamiliar with these instructions
or children to use the mower. Local regulations
may restrict the age of the operator.
- The operator or user is responsible for accidents or hazards occurring to other people or their property.
Cutting height explanation: take 3cm level for example.
Cutting height: 3cm
3cm
Grass
Height
3.3 Charging station installation
- Choose best installation place, please make sure
it is flat, no water, no magnetic interference and no
obstacle in the front of charging station.
3.2 Hardware adjustments
Blade adjustment
The mowing system used by this mower is based on
an effective and energy efficient principle. Unlike normal lawn mowers, the mower cuts the grass instead of striking it off.
Rain sensors on the mower is optional (See P14-5.12 RAIN), we recommend you allowing the mower to mainly mow in
dry weather to obtain the best possible result. Even though the mower can mow in rain, wet grass easily collects on the mower and the risk of slipping on steep
slopes is greater.
The blades must be in good condition to obtain the best
mowing result. In order to keep the blade sharp for as
long as possible it is important to keep the lawn free from branches, small stones and other objects
(especially the objects less than 6cm height). Please fill up small holes and even out small mounds to make sure lawn is flat.
Charging station best install place:
1. Make sure it is flat
2. No magnetic interference
3. No water and far away from puddle
4. No obstacle in front of charging station
- Please fix the charging station on horizontal place.
X
X
OK
How to adjust the cutting height:
There are two cutting levels of this mower, 3cm or 4cm.
The user has to change the blades to adjust the cutting
height.
1. Stop the mower and take off the key.
2. Loose the screws on the blade holder.
- Lay virtual wire
in the middle of
charging station.
Blade holder
Blade holder
3. Adjust the cutting height by change the two blades.
4. Fix the blades to the holder with screws.
5. Turn over the mower to upside.
- Fix the charging
station with four
stakes by hammer.
Peg
IMPORTANT INFORMATION
Before fix the charging station on the lawn, please examine the lawn and decide the best location where
is easy for the mower to find the station for recharge.
IMPORTANT INFORMATION
Do not tread or walk on the charging station plate.
- 6 -
3. INSTALLATION
3.4 Virtual wire installation
The virtual wire can be installed in one of the following ways:
- Securing the wire to the ground with pegs.
It is preferable to staple down the virtual wire, if you
want to make adjustments to the virtual wire during
the first few weeks of operation.
- Bury the wire
It is preferable to bury the virtual wire(max depth: 5cm)
if you want to detach or aerate the lawn.
If necessary both methods can be combined so one part of the virtual wire is stapled down and the
remainder is buried.
- Install virtual wire with pegs 1 meter apart. It’s
best to use smooth radius corners than sharp angles . See pictures,
- Bury virtual wire below grass and fasten it on the ground with pegs, so that the mower should
not cut the wire. virtual wire
Add pegs in order to pull the virtual wire down to the ground surface, below the grass tips.
IMPORTANT INFORMATION
Hard or dry ground may cause pegs to break when
driving them in. In extreme cases, watering the lawn
where the pegs will be driven.
OK
- A minimum distances between the front of the charging
station and an obstacle is 2 meters. And make sure the distance from corner to front of charging station is at least
2.5 meters. Make sure to lay a 2.5 meters minimum straight-light of virtual wire in front of charging station.
- If a high obstacle, for example a house, wall, fence or
other obstacle which is higher than the cutting lawn borders the working area, the virtual wire should be laid
at least 35cm from the obstacle. This will prevent mower from colliding with the obstacle.
- If a passage or a ground with same height of cutting lawn, the virtual wire should be laid at least 10cm from the edge.
- A minimum distance between the pool edge of virtual wire is 35cm.
- A minimum distance between two corners is 1meter.
120
Passage or a ground with same level of the lawn.
10cm
Pool
Min:35CM
Max:1cm
- A maximum distance of the virtual wire to and from the island is 1cm, and fix the two wires with one peg.
House, wall, fence or other obstacle higher than the lawn
Min:35cm
15cm
Location 1.
15cm
Straight-line at least:2.5m
Location 2.
- 7 -
- There are two types of set up of the virtual wire around the charging station.
1. Put the charging station near corner. please take location 1 for reference.
2. Put the charging station in middle of wire, please take location 2 for reference.
Please make sure to set a straight-line at least of 2.5m in front of charging station. The charging station should be far away from puddle.
3. INSTALLATION
- Use the virtual wire to isolate areas inside the working
area by creating islands around obstacles that can not withstand a collision, for example, flower beds and
fountains. Run the wire out to the area, route it around
the area to be isolated and then back along the same route. If pegs are used, the wire should be laid under the same peg on the return route. When the virtual
wire to and from the island with a maximum distance
of 1cm, the mower can drive over the wire.
- Care must be taken not to create a corner sharper shorter than 90 degrees when setting up virtual wire.
A corner sharper less than 90 degrees can cause the
mower to lose track of virtual wire. We can make
greater than 90 degrees corner like follow picture
shows.
- If protected obstacles are grouped closely together
isolate them individually. Continuous virtual island
if obstacles are close to edge, leave them out of the
mowing area.
Incorrect corner
setup
Correct corner set up, using several angle to avoid an angle of less than 90°.
- A maximum distance between the wire and tree root is
20cm.
Max: 1cm
Min: 2m
Max: 1cm
35cm
Virtual wire
Max: 1cm
Virtual wire
Root
Max:20cm
- The distance between charging station and virtual loop should be 2 meters at least.
Greater than
2m
Proper setup in sharp corners
1cm
Virtual wire connecting
- Joining the virtual wire .
If the virtual wire is not long enough
and needs to be spliced: Use supplied
wire connector. It is waterproof and
gives a reliable electrical connection.
To splice: Insert both cable ends in the
connector. Now press down the button on
top of the connector fully. Use a pair of
pliers or the like, as the button on the
connector is difficult to press down by
hand.
Greater than 2m
Tree with hole or flowers around require placing a wire around it
- 8-
3. INSTALLATION
3.5 Virtual wire and charging station connecting.
1. Cut the two ends of virtual wire to a length of 1cm that’s convenient for reaching the virtual wire terminal on charging station.
Strip the two ends of wire.
WARNING
The charger is not water-proof, it must be located on a place which is dry and ventilated.
2. Connect the cut two ends of virtual wire to virtual wire terminal located on charging station randomly, there
is no positive and negative.
3.7 Recharge.
Recharge Voltage: 24V
Recharge current: 2A
There are two kinds of recharge:
1. Auto recharge.
2. Recharge by charger directly.
Auto recharge
1. When the display
shows picture to the
right, the robot is going to find virtual wire and follow it back to station for recharge.
3.The virtual wire light turns colorless while virtual wire connected well with charging station.
A failed connecting between virtual wire and charging station cause a blinking red light and send out a beeping from charging station.
2. The display is showing
picture to the right,
it’s in recharging.
WARNING
Redundant virtual wire at back ofcharging station must be cut off.
IMPORTANT INFORMATION
All the buttons (except the emergency switch and power button ) are locked which can not be used
during the robot is in recharging.
3.6 Power connection. a
screw it tightly.
-
2 1
+
Power terminal on charging station
+
1 2
-
Power terminal on charger
3. The mower reverses several centimeters and stop
there with entering standby mode after fully
recharged.
Recharge by charger directly.
1.Turn off the mower in safety way and take away the key.
2.Connect the charger to charging terminal on mower
and screws tightly.
3. Connect the charger to power supply.
2. Connect the charger with power supply.
3.Charging light on station in green: Non-recharging.
charging light on station in red: recharging.
- 9 -
4. CONTROL PANEL AND REMOTE CONTROL
4.2 Remote control 4. CONTROL PANEL AND REMOTE CONTROL
4.1 Control Panel view
2
the mower enters standby mode.
1
3
5
Speed down.
6
Enter MANUAL pattern
7
blade.
4 5 6
9
Enter AUTO pattern
10
Press it when the mower is on standby mode
or working, it goes back to charging station.
A.
Charging station symbol
B.
Rain sensor symbol
C.
Working schedule symbol
D.
Line symbol
E.
Auto mode
F.
Battery voltage
G.
Time setting
H.
Function setting
I.
Month / Date
J.
Week
K.
Hour / Minute
8
9
10
1 2
4
5
6
7
A B C D E F
11
G H
I J K
IMPORTANT INFORMATION
Remove the 2 batteries from remote control while it is in idle for a long time.
Press this button when the mower is operating, it goes home for recharge automatically.
4 Up / + :
-Select menu, go upward
-Select menu, go left
-Select figure, means +
Remote control can only be used when it has
a same frequency with mower. (The remote control
was matched with mower before leave the factory).
How to match the remote control with mower:
1. Turn on the charging station.
5 Enter button
-To confirm your selection or enter it.
6 Down / -
-Select menu, go down
-Select menu, go right
-Select figure, means -
2. Take the remote control near charging station.
3. Press ON/OFF button on remote control until
the indicator light is blinking. Then release the
ON/OFF button.
4. It finishes matching with the robot while the
indicator light stop blinking.
- 10 -
5. USE
5. USE
IMPORTANT INFORMATION
- Do not leave the mower to operate unattended if you
know that there are pets, children or people in the
vicinity
- Mow only in daylight or in good artificial light.
- Avoid operating the mower in wet grass.
- Do not operate the mower when barefoot or wearing
open sandals.
- Always wear substantial footwear and long trousers.
- Always be sure of your footing on slopes.
- Use extreme caution when reversing the mower
towards you.
- Always switch on the mower according to instructions
with feet well away from the blade.
5.2 Starting the mower
There are two locations of start the mower.
1.Put the mower clockwise onto virtual wire, make sure
that the mower is not connected with two charging sheets on charging station. Otherwise, the mower is in recharging mode, it can not be started.
2.Take the robot to start point.
To set LINE on, the robot goes straight to find virtual wire and follow it back to charging station, it begins cutting inside lawn after it meets the charging station.
To set LINE off, the robot begins cutting inside lawn
directly.
WARNING
Read the safety instructions before you start your mower.
WARNING
Keep your hands and feet away from the rotating blade. Never put your hands or feet close to or under the body when the motors are running.
IMPORTANT INFORMATION
It’s a normal phenomenon that the mower goes a
circle to calibrate direction while it is working inside of signed lawn. If it meets obstacle or detects virtual wire before it finishes a circle, it will go on to make a new circle in new place.
5.1 Preparation
- Ensure the correct installation of the virtual wire.
- Periodically inspect the area where the mower is to be used and remove all stones, sticks, wires, bones, and other foreign objects especially the height
of the object is less than 6cm.
- Periodically visually inspect that the blades, blade
bolts and cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets to
preserve balance.
- Connect the two ends of virtual wire to the terminal
on charging station, and ensure virtual wire is in good
connecting. (Light on charging station is in colorless).
- Insert charger into charging station and secure it with
threaded cap. And then connect charger to power supply. Ensure the charging station has good connecting,
light on charging station is in Green.
- Periodically inspect the lawn is without any small
hole or mound.
IMPORTANT INFORMATION
User can not start the mower if virtual wire or charging station is not in good connecting.
- 11 -
To start the robot.
1.Turn on the key switch.
2.Clockwise rotate the Emergency switch on control
panel to turn on the robot.
3. Input Password (Initial password:0000), the robot
enters on standby mode.
4. Set Address to match with charging station firstly,
otherwise, the robot can not be started.
5. Select AUTO mode, the mower start working.
5.3 Stopping mower /Turning off mower
1. Press power button from remote control. Mower
stops and enters standby mode.
2. The mower also can be powered off by press the
Emergency switch directly.
3. Rotate the key to power off the mower.
5.4 Emergency Switch
Press Emergency switch at any time the robot power off at once. User has to restart it.
TIME
Robot mower main menu
AUTO
SET
SYSTEM TIME
SCHEDULE TIME
5. USE
Year
Week
Month / Date
Hour / Minute
SAVE / EXIT
MON,TUE,WED,THU,FRI,SAT,SUN, EXIT
EXIT
START TIME
00:00
AREA 1
000 MIN
AREA 2
000 MIN
AREA 3
000 MIN
SAVE / DEL / EXIT
Enter the AUTO mode?
YES / NO
PASSWORD
OLD PASSWORD
NEW PASSWORD
SWITCH
SAVE / EXIT
ON / OFF
ADDRESS
INITIAL
SET ADDRESS
Initial now? YES / NO
LANGUAGE
AREA
RAIN
English / French / German / Danish / Swedish / Spanish / Italian
EXIT
AREA 1
AREA 2
AREA 3
START / EXIT
Set Rain Sensor ON / OFF
LINE
EXIT
Set LINESENSOR ON / OFF
- 12-
5. USE
5.5 System time setting
1. Select TIME and enter it by pressing key .
2. Select SYSTEM TIME and enter it by pressing key .
7. Press key or key to scroll to SAVE and save the .
settings by pressing key .
8. Select DEL to delete the settings.
IMPORTANT INFORMATION
By using SCHEDULE function, the LINE must be turn on or the robot must be put onto virtual wire. Otherwise, the robot don’t works under schedule time setting.
3. To set Year.
- Press key or key to scroll to Year setting.
press key to enter Year setting.
- Press key or key to scroll to the correct Year.
and confirm the setting by pressing key .
4. Set Week, Month/Date, Hour/Minute as Step 3.
5. Press key or key to scroll to SAVE and save the .
setting by pressing key .
5.7 Password setting
1. Select SET and enter it by pressing key .
2. Select PASSWORD and enter it by pressing key .
5.6 Schedule time setting
The schedule time setting should be used together
with AREA function. P14-5.11 AREA setting.
1. Select TIME and enter it by pressing key .
2. Select SCHEDULE TIME and enter it by pressing key .
3. Select WEEK (
MON,TUE,WED,THU,FRI,SAT,
SUN)
and enter it by pressing key .
4. To set START TIME.
- Select START TIME and enter it by pressing key .
- Press key or key to set Hour/ Minute.
and confirm the settings by pressing key .
5. To set working time in each area.
- Select AREA 1 and enter it by pressing key .
- Press key or key to set how long should the robot
.10minutes for each scrolling.(From 000 to 250minutes).
6. Set AREA 2 and AREA 3 as Step5.
3. Initial password: 0000
4. To input OLD PASSWORD.
- Press key or key to scroll to OLD PASSWORD
press key to enter it.
- Press key or key to scroll to the correct password.
and confirm the setting by pressing key .
5. To set NEW PASSWORD as Step 4.
6. Press key or key to scroll to SAVE and save the
setting by pressing key .
Password function is optional.
SWITCH ON: every time the robot starts,
user has to input correct password.
SWITCH OFF: user does not need to enter password
when starts the mower.
5.8 Address setting
The robot communicates with charging station.
There is an ADDRESS between robot and charging station. User has to set the address before using it.
Otherwise the robot can not start working. A label with
Address Code pasted on charging station.
To set the address:
1. Put the mower near charging station.
2. Select SET and enter it by pressing key .
3. Select ADDRESS and enter it by pressing key .
4. Input the Address Code
as the label pasted at the
back of charging station.
5. Re-start the mower to find
from display, then the
address setting is finished.
SIA “Smartrobby”
Product name: Robot lawn mower
Model: S520 IP54
Input: 29.4 V 4A
Ouput 29.4 V 4A
Made in China
Address:XX
R
O
HS
Explanation:
- If Set AREA 1 with 000 minute, it means Non-cutting in
AREA 1.
- If user doesn’t select working in AREA 2. (See P14-
5.11AREA SETTING ). Even user has set a working
time in AREA 3, robot will not work in AREA 3.
5.9 Initial setting
Restore to factory settings.
1. Select SET and enter it by pressing key .
2. Select INITIAL and enter it by pressing key .
- 13 -
3. Select YES / NO and confirm the selection by pressing key .
5. USE
5.10 Language selection
1. Select SET and enter it by pressing key .
2. Select LANGUAGE and enter it by pressing key .
3. Select English / French / German / Danish / Swedish/
Spanish / Italian and confirm the selection by pressing
key .
- It’s best to set the Memory point in the middle of two corners.
- A better position of Memory point is a length of 3m’s virtual wire at the beginning or the end of an area.
- Route the wire around the passage to separate the area.
The virtual wire to and from the edge of passage is 1meter
at least. check the setting as below picture.
5.11 Area setting
This function is to increase the efficacity of the mower in a large area. It allows you to separate a larger are
into 3 small areas. The function should be used together with P13-5.6 SCHEDULE SETTING .
1. Select SET and enter it by pressing key .
2. Select AREA and enter it by pressing key .
- A minimum distance between the to and from virtual wire which
are to make a passage from one area to another one is 50cm.
Memory 3
Area 3
Min: 50cm
3. To select the working area.
- AREA 1 is non-optional, selects this by default.
- Press key or key to scroll to AREA 2 and press
key to select AREA 2 works.
IMPORTANT INFORMATION
If user does not select working in AREA 2, he can not set the robot working in AREA 3.
Max: 1m
Area 1
Memory 1
Min: 50cm
Min: 1m
Passage
Area 2
Memory 2
- Put the robot back to charging station and wait for working.
- Press key or key to scroll to AREA 3 and press
key to select working in AREA 3.
4. To set the Memory Point.
A Memory point is to program the mower to leave the
virtual wire. Each area should with a Memory point,
3 Memory points maximum in one mower.
Please keep the voltage of mower more than 27V before setting the memory points.
5.12 Rain
RAIN ON: mower goes back to charging station when it
is raining.
RAIN OFF: mower goes on working when it is raining.
1. Select SET and enter it by pressing key .
2. Select RAIN and enter it by pressing key .
3. Select YES / NO and confirm the selection by pressing key .
- Put mower onto virtual wire with a maximum distance of
1meter from charging station, and put the backside of
mower towards to charging station.
- Select START and confirm it by pressing key . Then
the robot starts follow virtual wire walking.
5.14 LINE
LINE ON: every time the mower started, it has to find virtual wire and follow it back to charging station. - Press key to set Memory point in AREA 1 when mower
arrives at Memory 1.
Press key to set Memory point in AREA 2 when mower
arrives at Memory 2.
Press key to set Memory point in AREA 3 when mower
arrives at Memory 3.
LINE OFF: if mower is not put onto virtual wire, it will not follow virtual wire walking when start it.
1. Select SET and enter it by pressing key .
2. Select LINE and enter it by pressing key .
Take Memory 1, Memory 2, Memory 3 as below picture
for example.
- 14 -
3. Select YES / NO and confirm the selection by pressing key .
6. MAINTENANCE AND STORAGE
6. MAINTENANCE AND STORAGE
- During maintenance operations, use the individual protections indicated by the Manufacturer , especially
when intervening on the blade.
- Before performing maintenance operations, make sure that the robot has stopped in safety conditions.
PROGRAMMED MAINTENANCE INTERVALS CHART
Frequency Component Type of operation Reference
15. Servicing of the mower should be according
to manufacturers instructions. This product
(include battery pack) must be disposed of at a designated collection pint for electrical and electronic waste. For more information, contact your local city office or the shop where you purchased the product.
Every week
Every month
Blade
Robot
Robot
Clean and check the efficiency of the blade
If the blade is bent due to an impact or if it is worn-out, replace it.
Carry out cleaning
Carry out for rechage
See “Robot cleaning”
See “Blade replacement”
See “Robot cleaning”
See “Battery”
6.2 Robot Storage
Packed the mower and all spareparts with the original package, and storage the carton off the ground in a cool, dry place. Temperature should not be colder than -4F°(-20℃)
6.3 Blade replacement
Blade model: 158NB
Blade replace steps:
1.Stop the robot in safety conditions.
2. Wear protective gloves.
3. Turn the Robot upside down.
4. Unscrew the blade and remove it.
5. Replace a new blade and screw it tightly.
6.1 Robot cleaning
1.Stop the robot in safety conditions.
2. Wear protective gloves.
3.Clean all the outside surfaces of the robot with a sponge soaked in warm water.
4.Do not use solvents or benzene so not to damage the varnished surfaces and the plastic components.
5.Do not wash the inside parts
of the robot and do not use water
jets in pressure so not to damage
the electric and the electronic
components.
WARNING
6.4 Battery
The battery is maintenance-free, but has a limited life
span of 1-3years. Battery life is dependent on the length of the using season and how many hours per week the robot is used. A long season or many hours of use per week, means that the battery must be replaced more regularly.
Never use a high-pressure washer or even running water to clean the robot.
6.Check the lower part of the robot (cutting blade area
and wheels) and remove the deposits and/or residues
that might obstruct the correct functioning of the robot.
7. To remove the deposits and/or other residues from the blade, use a suitable brush.
8. Clean the outside of the charging station from any accumulated residues.
- Attentions of batteries
Please charge the batteries in accordance with standard standard time and procedures.
When the power is too low. It should be started charging
as soon as possible.
Storage, we suggest the optimum storage of batteries with 80% power and keep in the shade.
9. Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working condition.
10. Replace worn or damaged parts for safety.
Don’t take a part, repair or modif the batteries.
Don’t connect the anode and cathode of batteries.
11. Ensure that only replacement cutting means of the
right type are used.
12. Ensure that batteries are charged by using the correct
charger recommended by the manufacturer.
13.Incorrect use may result in electric shock, overheating or leakage of corrosive liquid from the battery.
14. In the event leakage of electrolyte flush with water/neutralising agent, seek medical help if it comes
into contact with the eyes etc.
- 15 -
- Disused battery processing
Please contact the nearest waste treatment center and consultation with recycling and proper disposal of views.
IMPORTANT INFORMATION
Charge the battery fully at the end of the season
before winter storage. And recharge it every 3 months.
7. TROUBLE SHOOTING
Problem
After enter the correct password and select
AUTO mode, but the mower still can not start.
And the charging station is beeping.
After enter the correct password and select
AUTO mode, but the mower still can not start.
7.TROUBLE SHOOTING
Display Possible reasons Solutions
1.The virtual wire fails to send signals.
2.The virtual wire was cut off.
1.Check the virtual wire light on charging station.
Be sure the virtual wire is connected to the charging station well (light in colorless).
2. Connect the virtual wire
with wire connectors.
1. No power to plug receptacle or main power is shut off.
Bad communication between charging station and the mower.
1. Check the power and make sure the charger is connecting well with power supplier and charging station.
Mower stops working and beeping.
Mower stops working and beeping.
Mower stops working and beeping.
Mower is tilted over than
30 degree from the ground.
Turn off the robot and take the robot to level ground.
Then restart the robot.
1.Mower is lifted from ground.
1. Take the mower on level ground and restart it.
2. Someone or object ride or sit on the mower.
2. Take the object away from mower and restart it.
1. Running wheel strike hard objects.
1. Clean the lawn and make sure it is free from hard objects..
2. The mower is trapped in lawn.
2. Clean the lawn where mower is trapped or restart the mower in another place.
Mower stops working and beeping.
- 16 -
1. Cutting height is too low
1. Adjust the cutting height to suitable height.
2. Blade strikes hard objects.
2. Clean the lawn and make sure it is free from hard objects..
3. Mower is trapped in lawn
3. Clean the lawn where mower is trapped or restart the mower in another place.
Problem
Remote control does not work.
The batteries can not recharged
Mower does not complete the edge.
Mower does not detect the charging station contacts.
Mower reached the
charging station when its contacts are above the charging sheets.
The mower behaves in an anomalous around flower beds.
The mower is very noise.
7.TROUBLE SHOOTING
Display Possible reasons Solutions
1. The battery is low.
2. Remote control is not match with robot.
1. Change new batteries.
2. Match the frequency with mower.
Power nearing natural end of life.
1. Grass is extremely overgrown or very wet,
2. Terrain needs landscaping repairs.
1.Send the mower to service station and replace the battery.
2. Check whether charger is well connected.
1. Cut the grass appropriate height.
2. Fill in all holes, cover or exclude all exposed roots
in order to smooth the terrain.
Obstacle along the path. Watch the full operation of follow virtual wire walking and confirm no obstacle is present.
The ground before the charging station isn’t flat.
Reset the charging station in a flat place.
Height difference between the charging station and lawn surface at the entrance to charging station.
Confirm the ground before the charging station is leveled with the station if necessary fill area with dirt and level off.
Virtual wire incorrectly placed
Relocate the virtual wire.
1.Damaged cutting blade. 1. Replace a new blade.
2.Cutting blade flooded by residues(tapes, ropes, plastic fragments, etc)
2. Stop the mower in safety, use protection gloves to avoid the risk of cuts on hands, remove the fold cause from blade.
3.The start of mower occurred with obstacles
being too closed (less than
1m away) or in presence of unexpected obstacles
(fallen branches, forgotten objects, etc.)
3. Start the robot in new place.
4. Get the motor repair or replace by service station.
5. Increase the cutting height or use a normal lawn mower.
4. Damaged running motor
5. Grass too high.
- 17 -
Robot Exploded View
8. EXPLODED VIEW
- 18 -
8. EXPLODED VIEW
Charging Station Exploded View
1.Top cover
2.PCB
3.Power terminal
4.Virtual wire terminal
5.Underpan
6.Copper sheet
7.Copper sheet permanent seat
6
7
1
2
3
4
5
- 19 -
Robot lawn mower
USER MANUAL
Advertisement
