WINNER
One Number Follow-Me Router User Manual
Version 4.9
CONTENTS
1.
OVERVIEW .......................................................................................................................... 4
1.1.
Packing List ............................................................................................................... 4
1.2.
Safety Guidelines ...................................................................................................... 5
2.
QUICK START GUIDE ............................................................................................................ 6
2.1.
General User Information ......................................................................................... 6
2.1.1.
Placement of the Device ........................................................................................... 6
2.1.2.
Interference to Medical and Personal Electronic Devices ........................................ 6
2.1.3.
Antenna Considerations ........................................................................................... 6
3.
INSTALLATION AND SETUP ................................................................................................... 7
3.1.
STAGE 1 - Identifying Potential Sources of Interference .......................................... 7
3.2.
STAGE 2 - Assessing the Subscriber Site ................................................................... 7
3.3.
STAGE 3 - Installing the system ................................................................................ 8
3.4.
STAGE 4 - Abstract .................................................................................................... 8
3.5.
STAGE 5 - Programming ............................................................................................ 9
4.
PROGRAMMING THE GSM ................................................................................................. 10
4.1.
Software Installation............................................................................................... 10
4.2.
Programming with the PC Software ....................................................................... 12
4.2.1.
Connecting .............................................................................................................. 12
4.2.2.
The FXO Port Configuration .................................................................................... 14
4.2.3.
The FXS Port Configuration..................................................................................... 15
4.2.4.
The GSM Port Configuration................................................................................... 16
4.2.5.
The Prefixes Table ................................................................................................... 17
4.2.6.
The Number List...................................................................................................... 18
4.2.7.
The Control via SMS Setting ................................................................................... 19
4.2.8.
The Gateway Setting ............................................................................................... 20
4.3.
Programming the Unit with DTMF ......................................................................... 21
4.3.1.
General Setting Parameters.................................................................................... 21
4.3.2.
Browsing Between Main Menus ............................................................................. 22
4.4.
List of Menus and their Functions .......................................................................... 23
4.4.1.
Functions ................................................................................................................ 23
4.4.2.
Menu Synopsis ........................................................................................................ 24
5.
CONFIGURING THE ROUTER ............................................................................................... 33
5.1.
Basic Configuration without PBX ............................................................................ 33
5.2.
Options of Operation .............................................................................................. 33
5.3.
Readdressing Incoming Calls from PSTN to GSM ................................................... 33
5.4.
Configuration without PBX ..................................................................................... 34
5.4.1.
Incoming PSTN Calls................................................................................................ 34
5.4.2.
Incoming Calls from GSM ....................................................................................... 34
5.5.
Call-Back to Incoming Calls from GSM.................................................................... 34
Follow-Me One Number Router User Manual
www.eurotech-communication.com
2
5.6.
5.6.1.
5.6.2.
5.6.3.
5.6.4.
Configuration with PBX ........................................................................................... 35
Configuration .......................................................................................................... 35
Incoming Calls from PBX Extension Line to GSM .................................................... 35
Incoming Calls from GSM to the Unit ..................................................................... 35
Outgoing Calls from Landline.................................................................................. 35
6.
APPENDIX A....................................................................................................................... 36
6.1.
Controlling the Router via SMS............................................................................... 36
6.1.1.
Adding a New Cellular Number to the List ............................................................. 36
6.1.2.
Erasing a Cellular Number from the List ................................................................. 36
6.1.3.
Changing the Parameters for “Follow-Me” ............................................................ 36
6.1.4.
Operating the Callback via SMS .............................................................................. 36
7.
GENERAL TECHNICAL INFORMATION .................................................................................. 38
7.1.1.
DTMF Dialing........................................................................................................... 38
7.1.2.
Normal dialing tone ................................................................................................ 39
7.1.3.
Congestion / Busy Tone .......................................................................................... 39
7.2.
Enviromental Characteristics .................................................................................. 39
7.3.
Labels ...................................................................................................................... 39
Follow-Me One Number Router User Manual
www.eurotech-communication.com
3
1.
OVERVIEW
This user’s manual will help you installing your WINNER PSTN–GSM gateway unit, and it will provide you
with basic guidelines to handle any problems that might arise.
In general, the WINNER PSTN-GSM gateway provides a flexible and cost efficient connection between your
LANDLINE Network and the GSM mobile networks. In essence, the device acts as a router that is
programmed to choose the Least Cost Route when you make a call from your PSTN line to a cellular phone.
The GSM gateway connects you to an extension and bypasses the telephone company thus significantly
reducing overhead costs of telephone calls.
Connect to your PBX or landline phone or even to a specific phone extension and you will save money on all
calls by bypassing the telephone network and obtaining direct access to the GSM networks.
Together, the embedded Wavecom Module and SIM cards which act as 'Smart' user ID cards that encrypt
voice and data transmissions and store data about the specific user and personal phone settings, make the
GSM gateway a cell phone in itself. The WINNER gateways are therefore an essential tool for cutting
overhead costs of telephone bills as they allow direct access to the GSM networks and cut costs of airtime
and interconnections.
The WINNER PSTN-GSM gateways are intended for middle to large enterprises but can as well be installed
on regular phone lines in your home or home office.
There are certain features that may be relevant to the product you have selected and some that are not.
However, all are discussed in the following manual.
The WINNER One-Number FOLLOW-ME PSTN Router unit, when used with the appropriate telephone
equipment (antenna, adapter, SIM cards, telephone PSTN line or LANDLINE-PBX) will function as an
ordinary PSTN line and support the following features:








Cost-saving routing of incoming calls
GSM and PSTN interconnection via internal LCR
'Follow Me' call forwarder to your personal mobile
Caller ID, LCD, RTC
FXO/FXS interface
Polarity Reverse
Outstanding voice performance and echo cancellation
‘CallBack'
1.1.
PACKING LIST
When you receive your WINNER device please inspect the package to verify that you have the following:
1) One PSTN Router Unit.
2) 110/220V Electric Power converter to 12V with cables supplied.
3) GSM Antenna – To be installed to the PSTN Router Gateway.
4) Com Cable – To connect to the PC.
5) Two Screws – To mount the router on the wall.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
4
6) CD – Containing the PC Management Software and User Manual.
1.2.
SAFETY GUIDELINES
For a safe and efficient operation of your WINNER gateway unit, please observe the following guidelines:
 Please read the installation instructions and safety guidelines in this user's manual carefully before









installing the unit.
Do not handle the equipment before disconnecting it from the electrical outlet
Do not use any cleaning agents or detergents on any exterior or interior surfaces If you intend to clean
the device, disconnect it from electrical outlet and use only a damp cloth.
Do not position device in a damp place; do not expose to water.
Do not expose to extreme temperatures: optimal operating temperatures are between -5° C to + 50°C
Position equipment in a stable environment; any sudden fall or sharp movement may damage the
device.
Do not cover or stick any foreign objects in devices' openings or ventilation holes.
Do not operate your device while any person is within 0.02m of the antenna. A person or object within
0.02m of the antenna could impair call quality and may cause the phone to operate at a higher power
level than necessary
Warning: Potentially Explosive Atmospheres.
Do not operate the WINNER near blasting caps, or in a blasting area. Avoid the possibility of triggering
an explosion
Do not operate your device’s transmitter in a hazardous atmosphere: an explosion or fire may result.
The telephone interface is not designed for outdoor application:
The RJ-11 cable must not be run to an outdoor telephone; this minimizes equipment exposure to
coupling or direct lightning surges.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
5
2.
2.1.
QUICK START GUIDE
GENERAL USER INFORMATION
2.1.1. PLACEMENT OF THE DEVICE
The WINNER GSM gateway unit is designed for installation on a vertical surface but may be mounted also
on a wall.
 If you wish to mount the device on a wall follow these steps:
1) Remove the black metallic strip used for hanging the unit on the wall by sliding it out from the back of
the WINNER unit.
2) Place the metallic strip on the wall to indicate the location of the screws.
3) Hold the strip to the wall and drill holes for the screws
4) Place the unit onto the wall by sliding the metallic strip back into its place.
2.1.2. INTERFERENCE TO MEDICAL AND PERSONAL ELECTRONIC DEVICES
Most electronic equipment are shielded from RF energy. Nevertheless, RF energy from the WINNER
transmitter may affect inadequately shielded electronic equipment. We therefore advise you to consult the
manufacturer(s) of your medical and personal electronic device(s), (e.g. a pacemaker or hearing aid) to
determine if they are adequately shielded from external RF energy.
Do not install a WINNER gateway unit in a health care facility, if regulations posted in the area restrict the
use of cellular phones. Hospitals and health care facilities may be using equipment that is sensitive to
external RF energy.
2.1.3. ANTENNA CONSIDERATIONS
Use only the supplied or approved antenna. An unauthorized antenna, modifications or attachments could
affect call quality.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
6
3.
INSTALLATION AND SETUP
The installation procedure consists of the following steps:





STAGE 1: Identifying potential sources of interference
STAGE 2: Assessing the subscriber site
STAGE 3: Installing the system
STAGE 4: Abstract
STAGE 5: Programming the unit according to User Manual
3.1.
STAGE 1 - IDENTIFYING POTENTIAL SOURCES OF INTERFERENCE
The electronic circuitry of some telephones may be insufficiently shielded to operate properly with the
WINNER gateway units. When making or receiving a phone call, if you hear a “humming” sound or noise in
the earpiece of the telephone connected to the WINNER, or if any other party hears the hum or noise,
move the telephone away from the WINNER. If moving it farther away has no effect, try using a different
telephone.
The WINNER is a two-way radio and as such, some occasional interference is unavoidable. For best results,
choose an electrical outlet away from obstructions. Do not place the WINNER near items which may
increase static, such as:












Electrical appliances
Lamps
Microwaves
TVs
Fax Machines 4 Feet (1.2 meters)
Computers 4 Feet (1.2 meters)
Refrigerator
Vacuum cleaner
Light dimmers
Fluorescent bulbs
Motors
Fans
3.2.
STAGE 2 - ASSESSING THE SUBSCRIBER SITE
The WINNER GSM gateway must be installed indoors:
 Basement installation is not recommended, it can be done, but you must use an external antenna.
 The device needs to be installed in a place in which the temperatures may not exceed the specified
operating temperature range (see safety guidelines above).
 You should make sure that there is sufficient air movement.
 Installation in higher locations is preferred i.e. near windows and outer walls.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
7
3.3.
STAGE 3 - INSTALLING THE SYSTEM
1) Inspect the package, you should see: a unit gateway, an antenna, an adapter, a User Manual. Please
note: the WINNER unit comes without the SIM card(s).
2) Connect the antenna at a distance greater than 1 meter from the unit. Location of the antenna is
important in order to get best performances, thus once you turn the power on, make sure you have
best reception and clear conversation with the unit.
3) Insert SIM card into the unit:
In case of single channel unit, insert the SIM card in the designated slot (on the right side panel)
adjacent to the antenna connection you will see a thin metallic black colored drawer. Use a small
pointed object such as the point of a ballpoint pen into the little hole on the right side of that
drawer/slot to open the drawer, then insert the SIM into that drawer (SIM face up) and close the
drawer firmly.
4) Connect the gateway unit to a PBX telephone network or telephone line with a RJ-11 cable on the left
side panel nearest to the LEDs.
5) Connect an ordinary analog telephone to the RJ-11 connector nearest to the power (pin 3 and 4 are
used for Tip and Ring).
6) On the left side panel you will find the POWER socket. Connect the adapter (provided with unit) to the
electrical outlet and then to the electrical socket.
Note: The power input is 90 –260 VAC and the output is 12 VDC 1.2 Amp.
7) Wait 90 seconds for the unit to startup.
3.4.
STAGE 4 - ABSTRACT
The Eurotech Communication one-number 'Follow Me' PSTN to GSM router with the Call-Back/CallThrough feature availability is a clever device that attaches to your home or office telephone PSTN or line
or PBX and forwards all incoming calls to your personal cell phone. 'Follow Me' enables you to accept
phone calls from your office or home line on your mobile anywhere, anytime.
Incoming telephone calls will be automatically forwarded to your mobile phone via the embedded LCR that
utilizes a SIM card of the same GSM network to forward the call to your mobile phone. This device is more
beneficial than similar services available from telephone companies as the inner SIM card enables you to
remain in the same GSM network and thus cut costs of interconnections and high airtime charges by taking
advantage of the lower tariffs of same GSM network calls.
The Call-Back/Call-Through features enables you to enter up to 32 approved numbers that has the
capability and the approval to enter into your organization’s PBX (i.e. the call will be made through your
PBX which will provide a dial tone immediately for Call-Through or the unit will call you back, thus giving
you a dial line Call-Back). These features will reduce the billing costs to your company up to 50% and more.
This allows you to decide which employee (telephone number) will be entered and defined as Call-Back or
Call-Through.
The ROUTER device readdresses calls from the landline network to the GSM network and vice-versa.
The readdressing of the calls to the appropriate GSM network is set according to the prefixes that were
updated to SIM 1 and SIM 2. All other prefixes NOT updated in SIM 1 and 2 will be readdressed to the PSTN
(landline).
Follow-Me One Number Router User Manual
www.eurotech-communication.com
8
Incoming call from PSTN can be redirected to the GSM network. User can set the number of rings from a
local line after which the call can be re-directed to the GSM subscriber that was pre-set. If an incoming local
call is answered PRIOR to the presetting of the required rings necessary to the deployment of the FOLLOWME feature, it is possible to connect this incoming local call to the GSM network in the following ways:
 Press ## and the incoming local call will be redirected to the GSM Number that was pre set in the
Follow-Me mode.
 Press # and then the GSM number, followed by #, the call will be redirected to the above GSM number
via the preset SIM.
3.5.
STAGE 5 - PROGRAMMING
Start the installation procedure of the Follow Me Call Back Router following the set-up and Installation as
follows:
1) Entering programming mode Via PC or DTMF.
2) SIM Settings – regarding with usage limits and other optional modes
3) Follow-me settings – to let the system call you while you are away from your office as if you where in
your office
4) Call Back Settings – to let waiting lines make the call when line is available again.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
9
4.
PROGRAMMING THE GSM
General Rule
Outgoing calls to GSM will be directed through either SIM 1 or 2 according to the prefixes. Incoming calls
from GSM to PSTN will come from SIM 1 only.
 Incoming GSM call can be automatically directed to a landline subscriber
 First contact is made between the GSM network and the gateway and a ring tone is heard followed by
dialing to a local subscriber. Another call to a local subscriber is possible without the need to disconnect
the connection between the unit and the GSM (using the "Repeat Call" feature).
Caller ID
The unit will display on its LCD screen the number of the subscriber making the incoming call. It is possible
to configure the redirection of the number to a local line. There are several options for controlling the call
disconnection.







User can set the dialing mode from the gateway to the PSTN as TONE or PULSE.
The user can set the PAUSE prior to the dialing of GSM to PSTN.
Programming is done via analogue telephone set to TONE (DTMF)
All set parameters will be saved once the handset is returned to its place.
Modifying the unit's parameters is possible only with a password which can also be changed.
User can upgrade the programming of the unit by connecting a PC to the DATA port.
A table of authorized numbers for the Call-Back and Call-Through can be updated via SMS messages.
Call Through
Call Through with List
Connection between the cellular phone and the gateway can allow for a dial tone of the PBX/PSTN if the
cellular number has been included in the table of authorization.
Call Through without a List
Connection between the cellular phone and the gateway can allow for a dial tone of the PBX/PSTN
without the need to have the cellular number included in the authorization table.
Call Back
Connection between the cellular phone and the gateway can allow the gateway to identify the number as
an authorized number and it then sends a busy signal to the cellular caller. The call is then disconnected
and the gateway immediately returns a call to the cellular caller and provides the caller with a dial tone. If
the cellular number is not authorized then the call will be redirected to the PSTN or local line. It is possible
to program the Call Back feature via PSTN or GSM.
4.1.
SOFTWARE INSTALLATION
1) Insert the Winner Router 4.9 Installation CD into to CD drive of the PC.
2) In Windows Explorer, navigate to the installation CD drive.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
10
3) Double click on
Software. The Installation Window will open.
to install the Winner 4.9 PC Management
4) Click Next.
5) The Choose Destination Location window will open.
6) Click Next.
7) The Ready to Install the Program window will open.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
11
8) Click install. The software installs itself. Wait until a completion message will appear.
4.2.
PROGRAMMING WITH THE PC SOFTWARE
4.2.1. CONNECTING
After installing the PC software, launch it and define the type of connection between the PC and the Router
as described below.
1) Launch the software by pressing
on your PC desktop, or by pressing: Start > Programs >
Eurotech-Communication > Winner Router v4.9 build14. The software window will open.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
12
2) Connect the com port cable from the router to the PC Com port.
3) Press
in the toolbar. The Select Connection window will open.
4) Select the Com Port to which the Router is connected to, the connection frequency should be 115200,
the Connection mode should be via Com port and the default Password is 0000.
5) Press OK to connect.
6) At the bottom of the window you will see the connection status. If connected you see the status
connected and the led image will be green.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
13
7) Version is the firmware version of the router.
8) At the box near it select the skin of the software (the look of the windows).
9) The Restart Gateway button will restart the program in the router.
10) The Refresh button will read again the data from the router.
11) In the About button you will see the software version and how to contact us.
12) After a change in the settings push the Save Data button in that window.
4.2.2. THE FXO PORT CONFIGURATION
1) Press
to configure the FXO port.
2) Select in the Access Mode box how to route the incoming calls from the FXO.
 Directly to FXS: All the calls will be routed to the FXS.
 Directly to GSM: All the calls will be routed to the GSM.
 Follow Me: All the calls will ring the FXS the Number of Rings before Follow Me then route to the
GSM Follow Me Number.
In the Directly to GSM Mode:
Test the Number for "Access to GSM": If enabled, when a call comes from the FXO and receive a
GSM dial tone, the router will check the dialed number if it is on the Numbers List and authorized
to call the GSM (has 1 in the GSM column).
Follow-Me One Number Router User Manual
www.eurotech-communication.com
14
The dialed number could be between the Minimum Digits and the Maximum Digits. If a number is
below the Minimum Digits the router will wait the Waiting Timer before returning normal
operation.
Select GSM Network via Prefixes: If enable the calls will be routed according to the Prefixes Table.
3) Select the Dialing Mode to be Pulse Dialing or Tone Dialing.
4) Select the Dial Pause between the last digit dialed and sending the number.
5) Enter the Country Code and the National Direct Dialing code, when you want the router to
automatically replace the Country Code with the National Direct Dialing, in calls from the GSM to the
FXO. Enter the Pause after NDD timer, between the NDD and the number.
6) Select in the Condense of Busy Tone the ON time of your Landline network busy tone signal.
7) Select in the Condense of Reorder Tone the ON time of your landline network reorder tone signal.
8) Enter in the Number Unobtainable Tone the time of constant tone the router will see as busy tone only
when needed.
9) The CID Type shows you the CID format the router recognizes (not changeable at this version).
4.2.3. THE FXS PORT CONFIGURATION
1) Press
to configure the FXS port.
2) Select enable in the Unlisted GSM Number to readdress the incoming GSM calls, which are not on the
list, to the FXS port. If disabled the calls will be rejected.
3) Select enable in the CID Generation to FXS for the router to send the caller number to the FXS port.
4) Select in the CID Generation to Type the format of the CID in which the number will be sent.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
15
5) Enter in the Dial Pause the time in units of 0.1 seconds between the last digit dialed and sending the
number.
6) Select in the Reverse Polarity Type the way the router will do the Answer Supervision at the end of the
call. The options are :
 Disable – No answer supervision.
 Battery Reverse – Reversing the power of the line in the time of the call.
 Double Reverse – Reversing the power of the line again at the end of the call.
 Break Line – No power in the line at the end of the call.
7) Select in the Answer Supervision Timer the time to do the Double Reverse and Break Line in 0.1
seconds units.
8) Select in the Ring Signal the timing of the ring pulses to the FXS or customize your own.
4.2.4. THE GSM PORT CONFIGURATION
1) Press
to configure the GSM connection setting.
2) Select in the Access Mode box how to route the incoming calls from the GSM.
 Directly to FXS: All the calls will be routed to the FXS.
 Directly to FXO: All the calls will be routed to the FXO. Enter the desired PSTN number when you
hear the PSTN dial tone. Select Enable in Repeating "Access Mode" box. At the end of PSTN call dial
# to get a new PSTN dial tone. Enter in the Auto Dialing to FXO the PSTN number to dial
automatically (16 digits).
Follow-Me One Number Router User Manual
www.eurotech-communication.com
16
GSM Callback: If the GSM number is granted access to callback in the list, the router will disconnect
the call and call the number from SIM1 and will give him PSTN dial tone. Select in the Callback via
GSM/FXO from where the router will call you back the GSM or the PSTN. When a callback is from
the PSTN it will go to the FXS.
 GSM Conference: If the GSM number is granted access to conference in the list, the router will
disconnect the call and call the number from SIM1 and will give him a GSM dial tone.

3) Select in the Access via Number List, if the access to the FXO and FXS will be automatically or by the
accesses in the list.
4) Select Enable in the Private Incoming call to enable access for private calls (with no caller ID) to the FXS
(when the access is by the List).
5) Select Enable in the 'Ringback' Tone from the GSM Network to hear the voice of the rings to the GSM
from the GSM network itself.
6) Select in the Presentation of GSM Number if and when the SIM number will be shown to the recipient
of the call:
 CLIR by Network – The network decide if to show the number.
 CLIR Disabled – The number will not be shown.
 CLIR Enabled – The number will always shown.
7) Select in the Microphone Level the gain to the microphone volume (-6db to +6db).
8) Select in the Speaker Level the gain to the speaker volume (-6db to +6db).
9) Enter in the Pin Code for SIM1 and Pin Code for SIM1 the pin codes of the SIMs when Pin Code Request
is enabled at the SIMs.
10) Select in Voice Rate Type the codec for incoming and outgoing calls.
11) Select in Frequency Band the frequency the GSM network works with.
⇒ Note: If Voice Rate Type or Frequency Band ware changed you need to restart the router.
⇒ Note: The Network Status shows you the Cell and Network selection setting. This setting can be
changed only via the DTMF menu (see Programming with DTMF).
4.2.5. THE PREFIXES TABLE
1) Press
to set the SIMs Prefixes.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
17
2) There are up to 32 prefixes.
3) Enter in the Prefix column the prefix number (7 digits maximum).
4) Enter in the SIM Number column the SIM to call with (1 or 2 when available).
5) When you dial a number in the PBX, the router will check which SIM has the prefix in the table and
routes the call through that SIM. If the prefix is not in the list, the call will be routed to the PSTN.
6) The priority is always to the lower number in the prefix table.
7) Push the Save Data button to save the changes.
⇒ Note: The cursor must point to an empty box when you press Save Data.
4.2.6. THE NUMBER LIST
1) Press
to set the GSM Numbers List.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
18
2) There are listings of up to 64 GSM numbers in the list.
3) Enter in the GSM number column the GSM number (16 digits maximum).
4) Enter in the FXO column 1, to allow the calls from that GSM number access to FXO.
5) Enter in the FXS column 1, to allow the calls from that GSM number access to FXS.
6) Enter in the Callback column 1 to allow the calls from that GSM number to be called back by the router.
7) Enter in the Conference column 1 to allow the calls from that GSM number to do a conference call.
8) Enter in the GSM column 1 to allow the calls from the FXO access to that GSM number (test for 'access
to GSM' in the FXO setting needs to be enabled).
9) Push the Save Data button to save the changes.
⇒ Note: The cursor must point to an empty box when you press Save Data.
4.2.7. THE CONTROL VIA SMS SETTING
1) Press
to set the control via SMS settings.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
19
2) Select Enable in the Control setup via SMS to allow the control of the router by SMS.
3) Select Enable in the Receiving SMS control from specific number to allow only SMS from the Specific
GSM Number to control the router.
4) Select Enable in the Sending Confirmation SMS when you want the router to send back SMS that's
confirming the arrival of the control SMS.
5) Select Enable in the Callback via SMS to enable the operation of the callback by SMS command.
6) Select Enable in the Callback Number and FXO via SMS to enable the operation of the direct callback to
the FXO number by SMS command.
7) Enter in the Specific GSM Number the GSM number that’s allowed to control the router via SMS if
enabled (see clause 3).
8) Enter in the Service GSM Number the service number that's always allowed the control of the router
via SMS.
9) See appendix A to see the list of instructions how to control the router via SMS.
4.2.8. THE GATEWAY SETTING
1) Press
to set the Gateway settings.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
20
2) Select Data Mode in the Work Mode Box to enable sending and receiving data from the module.
3) Select in the Dial Tone box the frequency of dial tone. Select in the Level Box the volume level of the
dial tone.
4) Select in the Busy Tone box the frequency of busy tone. Select in the Level Box the volume level of the
busy tone.
5) Select in the Reorder Tone box the frequency of reorder tone. Select in the Level Box the volume level
of the reorder tone.
6) Select in the Ringback Tone box the frequency of ringback tone. Select in the Level Box the volume
level of the ringback tone.
7) Select in the Cadence Busy Tone the ON/OFF timing of the busy tone in units of 10ms.
8) Select in the Cadence Reorder Tone the ON/OFF timing of the reorder tone in units of 10ms.
9) Select in the Cadence Ringback Tone the ON/OFF timing of the ringback tone in units of 10ms.
4.3.
PROGRAMMING THE UNIT WITH DTMF
4.3.1. GENERAL SETTING PARAMETERS
Connecting the unit for programming mode:
 Connect an analogue phone with dial tone only to the local line port of the unit.
 Connect power source to the unit.
 Entering programming mode.

Follow-Me One Number Router User Manual
www.eurotech-communication.com
21
→ Pick up the handset
PROCEDURE #
1
2
3
ACTION
LCD READ
Enter the programming
mode
Router- v.4.9 –R4
If SIM is in place:
GSM --- LINE
If no SIM is in place:
NOT GSM --- NOT LINE
Pick up handset
DIAL: LOCAL LINE
A dial tone
Press # #
ENTER PASSWORD
Two beeps
ENTER PASSWORD 0000 and
#
INVALID PASSWORD
Quiet
Busy signal
4
Enter password
In case wrong password is
inserted
5
press #
MENU # 1.0 LOCAL
NETWORK
Completion of Programming
Mode:
Return handset to its place
SAVING PARAMETERS:
ROUTER
– V4.9X-R4 GSM – LINE
or
NOT GSM – NOT LINE
6
HEAR OVER HEADSET
4.3.2. BROWSING BETWEEN MAIN MENUS
PROCEDURE #
ACTION
LCD READ
HEAR OVER HANDSET
1A
Pick up handset
MENU #1.0 LOCAL
NETWORK
No sound
1B
Press # to enter local
network
MENU #2.0 PREFIX FOR GSM
2 beeping tones
2A
Press * for access to GSM
NETWORK menu
MENU #2.0 GSM NETWORK
2 beeping tones
2B
Dial # and enter GSM
NETWORK
MENU #2.1 ACCESS TO PSTN
2 beeping tones
3A
Dial # to enter LANDLINE
NETWORK
MENU #3.0 LANDLINE
NETWORK
2 beeping tones
3B
Dial # to enter LANDLINE
NETWORK menu
MENU #3.1 ACCESS TO GSM
2 beeping tones
4A
Dial * for Gateway
MENU #4.0 GATEWAY
2 beeping tones
Follow-Me One Number Router User Manual
www.eurotech-communication.com
22
PROCEDURE #
ACTION
LCD READ
HEAR OVER HANDSET
4B
Dial # and enter Gateway
menu
MENU #4.1, SETTING
PASSWORD
2 beeping tones
5A
Dial * to access SMS menu
MENU #5.0, SMS
PARAMETERS
5A
Dial # and enter SMS
⇒ Dial * to return to beginning of menu
4.4.





Control by list by over SMS
LIST OF MENUS AND THEIR FUNCTIONS
To browse between menus, press *
To enter into a menu, press #
To browse in a particular menu, press *
To enter into a function in a menu, press #
To exit menu press Short Flash
4.4.1. FUNCTIONS
Menu #1.0
1.1
1.2
1.3
1.4
Prefix for GSM
Dial Pause
Generation CLI
Reverse Polarity
Menu #2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
LANDLINE network
FXO Access Mode
Follow Me
Dialing Mode
PSTN/Ext.L Tones
Menu #4.0
4.1
4.2
4.3
4.4
4.5
GSM network
Unlisted Call
GSM Access Mode
Repeat Call
Call Back
Access Via list
GSM number list
Ring Back Tone
CLIR
Net/Cell Select
Menu #3.0
3.1
3.2
3.3
3.4
Local network
Gateway
Gain Control
Voice Rate
GSM Band
Setting Password
Setting Pin Code
Follow-Me One Number Router User Manual
www.eurotech-communication.com
23
4.6
4.7
4.8
Updating
Module ID (MID)
Work Mode
Menu #5.0
5.1
5.2
Control Follow-Me Call Back by SMS
SMS Control
Changing private password/PSW
4.4.2. MENU SYNOPSIS
MENU #
FUNCTION
1.1
Prefix for GSM
prefix
configuration per
SIM
1.2
Dial Pause
Delay in Dialing
Operation until
the actual dialing
occurs
LCD READ
ACTION
#XX for SIM: Y
Prefix: ZZZ
XX: Number of record
Y: Number of SIM
ZZZ: Prefix
To select XX:
For Browsing Down: digits 1or 2 or 3
For Browsing Up: digits 7 or 8 or 9
Updating record: press *
Updating Y (number of SIM):
SIM 1 = 1
SIM2 = 2
SAVE = #
Erase = 3456789*
Updating ZZZ (prefixes):
Enter digits from 0-9 to set the desired prefix
Erase = *
Save = #
Dial Pause in X
seconds
X is greater than or equal to 0.5 seconds and smaller
than or equal to 5 seconds.
Update the value of X to 0.5 seconds via *
0-9 digits; increase the value of X in leaps of 0.5
seconds
save Via #
Follow-Me One Number Router User Manual
www.eurotech-communication.com
24
MENU #
1.3
FUNCTION
Caller ID
Enables sending
CALLER ID to
local landline
phone
LCD READ
Generation: X
CLI: Y
ACTION
X = off or on
Defines possibility of option or not
Y= BELLCORE or BT_ON_HOOK
Defines completion time of CLI.
To browse between X options: press *.
To save press : #
To browse between Y options: press *.
To save press: #
1.4
Reverse Polarity
For monitoring
disconnection
Reveres polarity
Type X
ENTER PASSWORD and ****
X = Disable/Battery reverse/DBL. REV.POL./ Break
Line
To browse between the options for
X = Press *
To select the options: Flash
2.1
Unlisted Call
Incoming call
which is not
listed in the
Access List (Menu
2.5)
Unlisted Call
Accept: Enable /
Disable
Unlisted call Disable and Menu 2.5 Enable:
→unlisted calls are denied access to PSTN.
Unlisted call Enable and Menu 2.5 Enable
→unlisted calls are directed to local phone.
GSM Access
Mode: X
X = Access Mode.
Directly to FXS, Directly to FXO, Call Back or
Conference.
To select desired option = press *
To save press #.
AUTODIAL (numbers 0-9)
When X= Directly FXO
User can enter number of subscriber and the
incoming GSM
→Number will be redirected to that number.
If AUTODIAL will not be set then incoming GSM call
will receive a dial tone of the outgoing PSTN line
from the gateway
When X= Directly to FXS
Incoming calls to gateway's GSM will be redirected
to the local landline.
2.2
GSM
Access
Mode
Determines what
to do with GSM
incoming calls.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
25
MENU #
FUNCTION
LCD READ
ACTION
2.3
Repeat Call to
PSTN from GSM
Enables
disconnection of
ongoing PSTN call
while accessing a
Dial tone for an
additional call.
Repeat Call to
PSTN from GSM:
X
X = Enable (ON)/Disable(OFF)
* = Select option
# = Save
Continued on next page
2.4
Call Back
Call the unit Via
GSM or PSTN and
the unit calls
back providing
dial tone.
Call-Back will be
via: X
Edit Call-Back via
SMS: X
X= GSM or PSTN
* = browse through options of X
# = Save and move to next screen.
X= Enable/Disable
* = browse through options of X
# = Save
2.5
Access Via List
Authorization List
Allowing Access
to dial tone for
Call Through or
Call Back options
Access via list
Via list: X
GSM number list:
Key: * - Add
Key: # - Edit
X= Enable/Disable
* = browse through options of X
# = Save
* = To add a number and criterion (PBX or PSTN)
# = Proceed to menu # 2.6
Follow-Me One Number Router User Manual
www.eurotech-communication.com
26
MENU #
FUNCTION
LCD READ
ACTION
2.6
Browsing the
current list and
viewing records =
#
Editing the
records in the
table is as follow
X
#Y/FXO – O
FXS – S
Call-Back – Cb
Conference – Cn
GSM - G
X = the number of the subscriber needing
authorization
Y = the number of the record in the table
Z = Enable/disable PSTN
R= Enable/disable Call Back
Browsing the authorized records:
Upwards: 7 or 8 or 9
Downwards: 1 or 2 or 3
* = updating the displayed record
X = 0-9. Refers to the subscriber's number requiring
authorization.
* = Erase the X value.
# = Save the X and proceed to O.
* = YES/NO to enable O
# = Save O and Proceed to S.
* = YES / NO to S
# = Save S and Proceed to Cb.
Continued on next page
* = YES / NO to Cb
# = Save Cb and Proceed to Cn.
* = YES / NO to Cn
# = Save Cn and Proceed to G.
* = YES / NO to G.
# = Save G and proceed to next record in the table.
Flash = Exit to main menu.
2.7
Ring Back Tone
Ring back tone
from GSM: X
X = Enable/Disable ring back tone from the GSM
network.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
27
MENU #
2.8
2.9
FUNCTION
CLIR and Private
Sets whether the
outgoing call that
the unit is making
to the GSM will
be identified
NET/CELL
SELECT.
Allows you to
select specific cell
or network
LCD READ
ACTION
My number: X
Private call to
local line: X
X = set by Network /Enable number / Disable
Number
If * = Set by Network:
the identification will be set by the provider alone in
line with the provider's parameters
if * = Enable Number:
The call will be identified only if the provider
configured the SIM as identifiable
If * = Disable Number:
The gateway's number is not identifiable although
the provider has configured the SIM as so
# = Save selection and return to main menu.
X = ENABLE / DISABLE:
unidentifiable call to receive a dial tone when the
authorization table is in DISABLE mode
Network select:
X
Manual select: Y
#C Network: A
Period/Sec: B
Cell select from
network: Z
Cell select: R
X=Mode of selection.
Press * to Change from :
Auto select, Periodic Select, or Manual Select.
Continued on next page
Next: Press #.
Y = the network code.
#C = number of period (1 to 4).
A = the network code.
B = number of seconds for this period.
Next: Press #.
Z = the cell code.
R=Mode of selection.
Press * to Change from: Auto select, Periodic Select,
or Manual Select.
If R = Manual: press * to browse from the cells.
If R = Periodic: Prd = seconds for period.
Rx = only cells with level above Rx will be selected.
Press # to save.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
28
MENU #
3.1
3.2
FUNCTION
FXO Access
Mode.
Determines what
to do with PSTN
incoming calls.
Follow Me
Redirecting
incoming PSTN
local call to GSM
LCD READ
ACTION
FXO access
mode: X
GSM selection by
prefixes: Y
To test number
list: Z
X = Access Mode:
Directly to FXS, Directly to GSM, or Follow Me.
* = to select, # = to save.
Y=YES/No.
Either the GSM calls are routed by prefixes or all go
by SIM #1.
Z=YES/No.
If Z=YES, if the GSM number is with the Minimum
number of digits or maximum number of digits and
in the list with GSM =Y, then he will make the call.
Ring number: Y
“Follow me
number”: Z
Y = 0-9 ( SELECTING NUMBER OF RINGS)
# = Save number of rings and proceed to "Follow
Me" Number
Z = The number that will be designated as Follow
Me.
* = Resetting the above number.
# = Save and proceed to main menu.
Continued on next page
NOTE:
If Z is not designated and we are in Follow me
mode, an incoming PSTN call will receive a dial tone
for a GSM call.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
29
MENU #
LCD READ
ACTION
3.3
Dialing Mode
Set the dialing
parameters to
enable correct
Dialing
Min. dialing
digits: Mn
Max. dialing
digits: Mx
Dialing pause: Dp
Time waiting of
dialing: T
PSTN/Ext line
dialing: X
Country code: Y
Mn = In test mode minimum Number of digits to be
dialed.
Mx =In test mode maximum Number of digits to be
dialed.
Dp = The length of time between the end of DTMF
dialing and the sending of it.
T = Enter waiting time when less then minimum
digits.
X = Tone / Pulse
* = Select appropriate X
# = Save and proceed to selection of country code.
* = Reset Y
# = Save and proceed to NDD.
NDD( National Direct Dialing) = T
T= prefix for the region
* = Reset T
# = Save and move to PAUSE.
Pause After Dialing:
NDD (1 sec * ): z
Z = Delay time between 0 and 9 after completion of
NDD dial
* = reset Z
# = Save and proceed to main menu.
3.4
PSTN/Ext.L Tones
The tone
cadences setting.
Busy tone
ON/OFF: X
Reorder tone
ON/OFF = Y
X=the cadence time in milliseconds that the router
will recognized as busy.
Y=the cadence time in milliseconds that the router
will recognized as reorder tone.
4.1
Gain Control
Determines the
strength level of
Speaker and
Microphone
Speaker -6/+6
Microphone
-6/+6
Browse No. Down = press Numbers 1,2,3
Continued on next page
Browse No. UP = press Numbers 7,8,9
Save by #.
4.2
Voice Rate Type
Out coding: X
In coding: Y
X=The outgoing voice coding type.
Y=The incoming voice coding type.
Frequency Band:
X
X=The frequency that the router will work in.
* = to select: from: 850; 900; 1800; 1900;
Dual:850/1900; Dual:900/1800; Dual: 900/1900.
# = to save.
4.3
FUNCTION
GSM Band
Follow-Me One Number Router User Manual
www.eurotech-communication.com
30
MENU #
FUNCTION
LCD READ
ACTION
Enter new
password: X
X= Password to enter programming mode Default
password is: 0000
Setting new password:
After entering menu 4.2, user must key the old
password (0000 is initially set) and then #. The LCR
will read "Enter New Password" and user will then
enter the new password with 4 digits and then key
#.
Setting PIN SIM:
X
PIN SIM: Y
X = 1 = SIM 1 - SIM 2 =2
Y= SIM PIN CODE: 0-9
* =Erase Pin Code
# = Select appropriate X and save.
Flash = Exit to main menu.
4.4
Setting password
4.5
Setting PIN Code
Setting PIN CODE
of the SIM inside
the unit.
4.6
Updating
Updating - Restricted to Eurotech.
No access to client.
4.7
Module ID
Module ID (MID)
# = Restricted to Eurotech.
* = Restricted to Eurotech.
Flash = Back to main menu
4.8
Router Work
Mode
Work mode: X
X= Voice mode/Data mode.
* = to select
# to save
Follow-Me One Number Router User Manual
www.eurotech-communication.com
31
MENU #
5.1
5.2
FUNCTION
Setting for SMS
Determining the
parameters to
allow control of
authorization list
of Call-Back and
Call-Through
Changing Private
Password /PSW
Modifying access
code for setting
parameters to
configuration of
SMS.
LCD READ
ACTION
Setting for SMS
Confirm: X
Control by list via
SMS: Y
Confirm action
via SMS: Z
Private number
from SMS: R
Private number:
T
Control digit: W
Service setting: Q
Code for entry to modification of configuration for
SMS
X = 12345678 (DEFAULT)
Continued on next page
Y = Enable / Disable
* = Select Y
# = Save and Proceed to "Confirm Action" option.
Allows FEEDBACK option via SMS to the cellular
phone confirming modification
Z = Enable / Disable
* = Selecting options or Z
# = Save and proceed to "Private Number " option
Unique Subscriber number from which
modifications in SMS can be completed.
R = Disable / Enable
* = Option for selecting R
# = Save and proceed to "Private Number " option
T = Number from which SMS messages will be sent
*= Erase number
# = Save the number and proceed to "Control Digit"
option
W= Code key that will accompany the SMS
message.
* = Erase
# = Save and proceed to service setting
Q = service number that can always control via SMS.
Confirmation
password: Y
Enter new code
Y = 12345678 (Default)
User must enter previous code.
X = new 8 digit password for setting new SMS .(See
5.1)
# = Save
Flash = Exit to menu
see 1.5
instructions on how to control the unit Via SMS
Follow-Me One Number Router User Manual
www.eurotech-communication.com
32
5.
CONFIGURING THE ROUTER
 Ways of connecting the router to the landline and GSM networks, PBX
 Ways of operating in different configurations
 Router to PSTN/GSM
5.1.
BASIC CONFIGURATION WITHOUT PBX
1) Landline parameter
 Menu 3.1 - GSM Access Mode → Directly to FXS
 Menu 3.3 - Tone Mode - Tone/Pulse according to country
2) Local line parameter
 Menu 1.1 - Setting prefixes → SIM 1, SIM 2
 Menu 1.2 - Dial Pause – Default 5 seconds (can be changed)
 Menu 1.3 - CLI - Enable
 Menu 1.4 - Reverse Polarity – Disable
3) GSM Parameter
 Menu 2.2 - PSTN Access Mode → Directly to FXS.
5.2.
OPTIONS OF OPERATION
Option 1:
Outgoing to PSTN: Dial number of PSTN from local line, 5 seconds dial pause
Connects to PSTN, enter the number to PSTN
 Option 2:
Dial number GSM Network A or B: 5 sec dial pause - A or B

Select SIM 1 or SIM 2 depending on prefix table → GSM network
In case of incoming PSTN calls the call will be transferred to the local line.
If the CLI is enabled the local phone will display the incoming number.
5.3.
READDRESSING INCOMING CALLS FROM PSTN TO GSM
 Incoming call to the local line from PSTN: Dial # XXXX (readdressed number) → Pause Dial. The call will




be sent to the GSM network where subscriber A or B will answer.
Incoming call to the local line from PSTN: Dial # XXXX # (readdressed number). The call will be sent to
the GSM network where subscriber A or B will answer
In case of a Follow-Me number, enter ## and the call will be sent from PSTN to GSM
If Follow-Me mode is ON and the number of rings to local line is set between 1 and 9, the unit will
generate the number of rings in the local line which will be forwarded automatically to the GSM
network
If the number of rings is set to "0" it will forward the call to the GSM network without any rings in the
local line
Follow-Me One Number Router User Manual
www.eurotech-communication.com
33
5.4.
CONFIGURATION WITHOUT PBX
Landline Parameter:
Follow-Me – OFF
 GSM Access Mode – Directly to FXO

GSM Parameter:
FXO Access Mode – Directly to GSM
 Local Line: Same parameters as in configuration 3.1.
 Outgoing calls from local line to PSTN work the same way as in configuration 3.1.

5.4.1. INCOMING PSTN CALLS
 Unit will work as a router
 All calls from PSTN will be diverted to GSM network A or B
 Incoming calls from PSTN: Unit will answer → subscriber will hear a dial tone → subscriber will dial
GSM number → Dial Pause → outgoing call goes to GSM network A or B.
⇒
If the subscriber dials the wrong number he can correct this only if done before the end of the dial
pause. Subscriber must press key # and enter the new number.
5.4.2. INCOMING CALLS FROM GSM
All calls will be diverted from GSM to PSTN. The GSM subscriber dials to the unit → unit answers →
subscriber receives dial tone → subscriber dials a PSTN number→ Dial Pause → outgoing call to PSTN
activated.

Option 1:
When session to PSTN from GSM is ended the GSM subscriber will still be
connected to the unit. He can press * # and will receive again a dial tone allowing him to make
another outgoing call to PSTN.
⇒ The gap between * and # mustn’t be longer than 5 seconds

Option 2:
Access to PSTN from GSM via list of subscriber numbers → menu 2.5: ENABLE →
when the incoming GSM call is listed, the unit will divert it to PSTN
5.5.
CALL-BACK TO INCOMING CALLS FROM GSM
Menu 2.1:
Disable
Menu 2.2:
GSM Access Mode – Call Back
Menu 2.4:
Call Back → call-back option is PSTN or GSM
 Call-Back will work only with a list of authorized numbers
 If the callback is via the GSM incoming calls, the incoming calls will be disconnected. If the unit has
connected already cellular A with PSTN and cellular B is calling, the unit will disconnect cellular B and
will call back B once A has ended the session.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
34
5.6.
CONFIGURATION WITH PBX
5.6.1. CONFIGURATION
Landline Parameter:
Menu 3.1:
FXO Access Mode: Directly to GSM
Menu 3.2:
OFF
Menu 3.3:
Dialing Mode
GSM Parameter:
GSM Access Mode:
Directly to PSTN
Menu 2.1:
Auto Dial (0-9)
Local Line Parameter:
Menu 1.1:
Prefix 1 – SIM 1, Prefix 2 – SIM 2
Menu 1.2:
Dial Pause, greater or equal to 0.5 seconds and less or equal to 5 seconds
Menu 1.3:
CLI – Enable
Menu 1.4:
Reverse Polarity – Enable
5.6.2. INCOMING CALLS FROM PBX EXTENSION LINE TO GSM
Extension will dial into the Router that is connected to the PBX and will receive a dial tone allowing the dial
of a GSM number.
5.6.3. INCOMING CALLS FROM GSM TO THE UNIT
Once auto dial number is set, all incoming GSM calls will be diverted to that extension number.
⇒ If auto dial is not set the GSM call will be diverted to a local line.
5.6.4. OUTGOING CALLS FROM LANDLINE



See configuration 3.1: PSTN numbers will be diverted to PBX and will out go through PSTN
GSM prefixes will be diverted to GSM network
Configuration 4.4: PBX is connected to CO (Central Office) Port
Follow-Me One Number Router User Manual
www.eurotech-communication.com
35
6.
APPENDIX A
6.1.
CONTROLLING THE ROUTER VIA SMS
To send a SMS command you must enable the parameter Control Setup via SMS in the PC software or SMS
CONTROL in menu #5.1.
6.1.1. ADDING A NEW CELLULAR NUMBER TO THE LIST
Send this SMS to the SIM1 number: 12345678.Add.nnnnnnnnnnnnnnn.P.S.C.N.G.
Where:







12345678 = the Control Code.
nnnnnnnnnnnnnnn = the GSM Number.
P = Yes/No for this number to access the PSTN (in the message appears Y or N).
S = Yes/No for this number to access the FXS (in the message appears Y or N).
C = Yes/No for this number to do CALLBACK (in the message appears Y or N).
P = Yes/No for this number to do CONFERENCE (in the message appears Y or N).
G = Yes/No for this number to access the GSM (in the message appears Y or N).
6.1.2. ERASING A CELLULAR NUMBER FROM THE LIST
Send this SMS to the SIM1 number: 12345678.Clr.nnnnnnnnnnnnnn.
Where:

nnnnnnnnnnnnnn = a GSM Number from the list that we want to erase.
6.1.3. CHANGING THE PARAMETERS FOR “FOLLOW-ME”
Send this SMS to the SIM1 number: 12345678.Flm.nnnnnnnnnnnnn.F.m.
Where:



nnnnnnn = number for FOLLOW-ME
F = Yes/No, to enable the FOLLOW-ME (in the message appears Y or N).
M = the number of rings until auto readdressing.
6.1.4. OPERATING THE CALLBACK VIA SMS
1) Calling the GSM Callback Number via SMS

Enable the parameter Callback via SMS in the PC Software or SMS: CALLBACK in menu #2.4.

Send this SMS to the SIM1 number: Cbnnnnnnnnnnnnnn
Where:

nnnnnnnnnnnnnn = the GSM Number to Call-Back (must be enabled for callback in the List).
2) Calling the GSM Call-Back Number and Connecting him to PSTN Number via SMS
Follow-Me One Number Router User Manual
www.eurotech-communication.com
36

Enable the parameter Callback via SMS in the PC Software or SMS: SENDING CALL of menu
#2.4.

Send this SMS to the SIM1 number: Scnnnnnnnnnnnnnn.mmmmmmmmmm
Where:


⇒
nnnnnnnnnnnnnn = the number to call via the FXO.
mmmmmmmmmm = the GSM Number to call back from the list.
If 'The GSM Number to Call Back' is not present then the callback will be made to the
number
which sent this SMS.
→ In this case 'NDD' and 'Country Code" parameters must be set in menu #3.3.
Follow-Me One Number Router User Manual
www.eurotech-communication.com
37
7.
GENERAL TECHNICAL INFORMATION

Electrical




























Power supply: 12 VDC +/- 5% 1,2A
720 mA average in GSM 900 at Tx power max 2W
920 mA average in GSM/GRPS 900 at Tx power max 2W
100 mA in idle mode
Physical
Absolute maximum dimension: 165 x 127 x 30mm
Weight: 600g
Casing: Complete shielding-stainless steel
Mounting: 2 screw holes
Operating temperature range: -5°C to + 55°C
Optimal storage temperature: -35°C to +85°C
Analog Telephone/LANDLINE-PBX interface
TIP/Ring Voltage: –48V
Line current: 25ma
Ringing Voltage: 140 Vpp
Load 3REN
Crest Factor: 1.25
Frequency: 20 Hz
Cadency: 2s/4s
Answer supervision - reverse polarity
DTMF compliancy
Dial Tone: 400 Hz
Busy Tone: 400 Hz, cadency 500ms/500ms
GSM Circuit Data Features
Data circuit asynchronous, transparent and nontransparent up to 14,400 b/s
Automatic fax group 3 (Class 1 & 2)
Alternate speech and fax
MNP2, V.42bis
7.1.1. DTMF DIALING
 Detection level:
-25dBm to +3dBm
 On time: 50msec
 Off time: 12 characters

Ringing Signal


Feeding type:
Distortion:
Balanced signal
Less than 5%
Follow-Me One Number Router User Manual
www.eurotech-communication.com
38



Ring drive capability
3 type A
Minimum ring Voltage: 40 Vrms – crest factor 1.2
Frequency:
(20 Hz )
7.1.2. NORMAL DIALING TONE
 Frequency: 400Hz
 Level:
2dB
 Cadence: continuous
7.1.3. CONGESTION / BUSY TONE
 Frequency: 400Hz
 Level: 2dB
 Cadence:
500ms 20% signal
 500ms 20% pause

7.2.
ENVIROMENTAL CHARACTERISTICS
The WINNER complies to the following requirements:





Temperature - we claim -5° to 70° (Israeli Standard Institute Approval is in process).
Humidity - 5% to 95%
Safety - Israeli Standard Institute Approval
Transportation - Transport conditions are according to EuroTech Standards.
Storage Condition - Storage conditions are according to class 1.1, ETS 300 019 –1-1 (-20°C +80°C), 25°C
to +65°C
7.3.
LABELS
The label contains this information:





Line 1: The Module Type and the Antenna Type
Line 2: The Router Type
Line 3: The Bootloader Program
Line 4: The Serial Number
Line 5: The Firmware Program
Follow-Me One Number Router User Manual
www.eurotech-communication.com
39
Download PDF