User Manual - J.P. Leisure

COLOR BURST
USER MANUAL
www.prolight.co.uk
CAUTION!
Keep this device away from rain and moisture!
Unplug the mains cable before opening the casing.!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
SAFETY INSTRUCTIONS
Every person involved with the installation, operation and maintenance of this
equipment must:
be qualified
follow the instructions of this manual
consider this manual to be part of the total product
keep this manual for the entire life of the product
pass this manual on to every further owner or user of the product
download the latest version of the user manual from the internet
CAUTION! TAKE CARE USING THIS PRODUCT
With high voltage you can suffer a dangerous
electric shock when touching wires!
This equipment has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual.
Important: Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to drastic temperature fluctuation (eg: after transportation), do not switch
it on immediately. The arising condensation may damage your equipment. Leave the equipment switched
off until it has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damage to the
power connection cable or on the casing, do not connect the equipment and immediately consult your
local dealer.
This equipment falls under protection-class 1. The power plug must only be plugged into a protection
class 1 outlet. The voltage and frequency must be exactly the same as stated on the equipment.
Incorrect voltages or power outlets can lead serious damage and electrical shock.
Always plug in the power plug last. The power plug must always be inserted without force. Make sure that
the plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution! Never touch them with wet hands, as this could lead to
electric shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate
next to sources of heat or cold. Disregard of this information can lead to power cord damage, fire or
electric shock.
The cable insert or the female part in the equipment must never be strained. There must always be
sufficient cable to the equipment, otherwise, the cable may be damaged which may lead to electric
shock.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the equipment and
the power-cord periodically.
If extension cables are used, make sure that the core diameter is sufficient for the required power
consumption of the equipment. All warnings concerning the power cables are also valid for possible
extension cables.
Always disconnect from the mains, when the equipment is not in use or before cleaning it. Only handle
the power-cable by the plug. Never pull out the plug by tugging the power-cable, otherwise, the cable or
plug can be damaged leading to an electric shock. If the power plug or the power switch is not
accessible, the equipment must be disconnected via the mains.
If the power plug or the equipment is dusty, the device must be taken out of operation, disconnected and
then be clean with a dry cloth. Dust can reduce the insulation which may lead to an electric shock. More
severe dirt in and on the equipment should only be removed by a specialist.
There must never be any liquid allowed to enter the power outlets, extension cables or any holes in the
housing of the equipment. In the event of any liquid entering the equipment, it must be disconnected
immediately. This is also valid if the equipment was exposed to high humidity. Also if the equipment is still
working, the equipment must be checked by a specialist.
There must never be any objects allowed to enter the equipment. This is especially valid for metal parts.
If any metal parts like staples or coarse metal chips are entered into the equipment, the equipment must
be taken out of operation and disconnected immediately. Malfunction or short circuits caused by metal
parts may cause injuries.
Keep away from children and amateurs!
Never leave the device running unattended.
Introduction
Features
CONTROL FEATURES
•4-channel DMX-512 LED par can
•Bl
ackout
/
Di
mmer
/
St
r
obe
•I
ndi
vi
dualcont
r
olofRed,Gr
eenandBl
uel
eds
Features
•86LED’
spersur
f
ace
- Red (44), Green (21), and Blue (21)
•Ul
t
r
abr
i
ghtLED’
s
•RGBcol
ourmi
x
i
ng
•Bui
l
t
-in colour change programs
•Lowpowerconsumpt
i
on
•Up to 100,000-hour LED life span
•Mas
t
er
/
Sl
av
emode
OPTIONS
•Pr
ogr
ammabl
e:Anyuni
v
er
salDMX-512 controller
DMX Channel Summary
CHANNEL
1
INTENSITY CONTROL OF
BLACKOUT/STROBE/DIMMER
2
RED
3
GREEN
4
BLUE
Product Overview
Setup
Power
Warning!
Verify that the power requirement printed on your unit matches the line voltage applied.
All fixtures must be connected to circuits with a suitable Earth Ground.
•Todet
er
mi
net
hepowerr
equi
r
ement
sf
orapar
t
i
cul
arf
i
xt
ur
e,seet
he label affixed to the
backoft
hepl
at
eoft
hef
i
xt
ur
eorr
ef
ert
ot
hef
i
xt
ur
e’
sspeci
f
i
cat
i
onschar
t
.
•Af
i
xt
ur
e’
sl
i
st
edcur
r
entr
at
i
ngi
si
t
’
saver
agecur
r
entdr
aw undernor
malcondi
t
i
ons.
•Al
lf
i
xt
ur
esmustbepower
eddi
r
ect
l
yof
faswi
t
chedci
r
cuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is
used solely for a 0% to 100% switch.
•Bef
or
eappl
yi
ngpowert
oaf
i
xt
ur
e,checkt
hatt
hesour
cevol
t
agemat
chest
he
f
i
xt
ur
e’
sr
equirement
•Al
lf
i
xt
ur
esmustbeconnect
edt
oci
r
cui
t
swi
t
hasui
t
abl
eEar
t
hGr
ound.
Operating Instructions
The Colour Burst is a DMX-512 controllable, full RGB colour mix par can made up of high
efficiency andsuperbr
i
ghtLED’
s.Ther
ear
et
hr
eecol
ourgroups (red, blue and green) whose
intensity can be controlled individually allowing the creation of an unlimited range of colours.
The Colour Burst can operate in stand-alone, Master/Slave and via DMX-512 control
utilizing 4 channels.
Master/Slave & Stand-Alone Mode
The Master/Slave mode will allow you to link up to as many units you want in a daisy chain
fashion. In this mode, the first unit in the daisy chain will automatically command all
other units following.
1)
2)
3)
4)
Connect all units in a daisy chain fashion as described in the section following
Master Unit: Set dipswitch No: 9 to on and No: 10 to off.
Slaves: Set dipswitch No: 10 to the on position and all others to the off position.
You can also run the fixtures in a automatic stand-alone mode by simply setting all fixtures
to run as mater units.
Daisy Chain Connection
1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3pin
connector of the first fixture
2) Connect the end of the cable coming from the first fixture which will have a (female) 3pin
connector to the input connector of the next fixture consisting of a (male) 3pin connector.
Then proceed to connect from the output as stated above to the input of the following fixture
and so on.
Built-in Program Options
There are 8 individual settings accessed by turning ON dipswitches 1 through 8 individually.
Manual Control Options
With all the dipswitches set to the off position, the dipswitches 1 –8 will control 3 levels of
i
nt
ensi
t
yf
orr
edandgr
eenLED’
sand2l
evel
sofi
nt
ens
i
t
yf
orbl
ueLED’
s
.
This allows you to statically set a colour of preference without the use of a controller. By setting
different intensities for all 3 LED colours you can compose a colour of your choice.
Manual Intensity Control RGB Mix
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest flexibility when it
comes to customizing or creating a show. In this mode you will be able to control each individual
trait of the fixture and each fixture independently. The Colour Burst uses 4 channels of control.
1. Enable the DMX control by setting dipswitch No: 10 to the ON position. Use dipswitches 1 –
9 to address each fixture accordingly.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller device. Each fixture requires a
“
st
ar
taddr
ess”f
r
om 1- 511. A fixture requiring one or more channels for control begins to read
the data on the channel indicated by the start address. For example, a fixture that occupies or
uses 7 channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
If this is your first time addressing a fixture using the DMX-512 control protocol Then I suggest
j
umpi
ngt
ot
heAppendi
xSect
i
onandr
eadt
heHeadi
ng“
DMXPr
i
mer
”
.I
tc
ont
ai
nsver
yus
ef
ul
information that will help you understand its use.
Set the start address using the group of dipswitches located usually on the bottom of the fixture.
Each dipswitch has an associated value. Adding the value of each switch in the ON position will
provide the start address. Determining which switches to toggle ON given a specific start
address can be accomplished in the following manner. By subtracting the largest switch value
possible from the selected start address until zero is achieved.
APPENDIX
DMX INTRODUCTION
There are 512 Channels in a DMX-512 connection. Channels may be assigned in any manner.
A fixture capable of receiving DMX-512 will require one or a number of sequential channels. The
user must assign a starting address on the fixture that indicates the first channel reserved in the
controller. There are many different types of DMX controllable fixtures and they all may vary in
the total number of channels required. Choosing a start address should be planned in advance.
Channels should never overlap. If they do, this will result in erratic operation of the fixtures
whose starting address is set incorrectly. You can however, control multiple fixtures of the same
type using the same starting address as long as the intended result is that of unison movement
or operation. In other words, the fixtures will be slaved together and all respond
exactly the same.
DMX fixtures are designed to receive data through a serial Daisy chain. A daisy chain
connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture.
The order in which the fixtures are connected is not important and has no effect on how a
controller communicates to each fixture. Use an order that provides for the easiest and most
direct cabling. Connect fixtures using shielded two conductor twisted pair cable with three pin
XLR male to female connectors. The shield connection is pin 1, while pin 2 is the Data Negative
(S-) and pin 3 is Data Positive (S+). CHAUVET carries 3-pin XLRDMX
compliant cables, DMX-10(
33’
)
,DMX-4.
5(
15’
)andDMX-1.
5(
5’
)
.
Fixture Linking
DMX Dipswitch Quick Reference Chart
DMX Address Quick Reference Chart
Dip Switch Position
DMX DIP SWITCH SET
0=OFF
1=ON
X=OFF or ON
#1 #2 #3 #4 #5
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
1
1
0
0
0
0
0
1
0
0
1
0
1
0
0
0
1
1
0
0
1
1
1
0
0
0
0
0
1
0
1
0
0
1
0
0
1
0
1
0
1
1
0
1
0
0
0
1
1
0
1
0
1
1
0
0
1
1
1
0
1
1
1
1
0
0
0
0
0
1
1
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
0
1
0
1
1
0
1
0
1
0
1
1
0
1
1
1
1
0
1
0
0
0
1
1
1
0
0
1
1
0
1
0
1
1
1
1
0
1
1
0
0
1
1
1
1
0
1
1
1
0
1
1
1
1
1
1
1
1
1
#9
#8
#7
#6
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
128 160 192
97
129 161 193
98
130 162 194
99
131 163 195
100 132 164 196
101 133 165 197
102 134 166 198
103 135 167 199
104 136 168 200
105 137 169 201
106 138 170 202
107 139 171 203
108 140 172 204
109 141 173 205
110 142 174 206
111 143 175 207
112 144 176 208
113 145 177 209
114 146 178 210
115 147 179 211
116 148 180 212
117 149 181 213
118 150 182 214
119 151 183 215
120 152 184 216
121 153 185 217
122 154 186 218
123 155 187 219
124 156 188 220
125 157 189 221
126 158 190 222
127 159 191 223
Dip Switch Position
01
1
1
1
1
0
0
0
1
0
0
1
224 256 288
225 257 289
226 258 290
227 259 291
228 260 292
229 261 293
230 262 294
231 263 295
232 264 296
233 265 297
234 266 298
235 267 299
236 268 300
237 269 301
238 270 302
239 271 303
240 272 304
241 273 305
242 274 306
243 275 307
244 276 308
245 277 309
246 278 310
247 279 311
248 280 312
249 281 313
250 282 314
251 283 315
252 284 316
253 285 317
254 286 318
255 287 319
DMX Address
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
DMX Channel Values
DEFAULT
VALUE
FUNCTION
Shutter/Strobe/Dimmer
Blackout
000
Strobe: speed > 001 - 152
Intensity: 0% > 153 - 242
1
000
001<>152
153<>242
2
000 <> 255
RED
0 > 100%
3
000 <> 255
GREEN
0 > 100%
4
000 <> 255
BLUE
0 > 100%
Technical Specifications
Weight & Dimensions
•Lengt
h….
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..................................125mm (4.92in)
•Wi
dt
h.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
125mm (4.92in)
•Hei
ght
…………………………………………….
.
200mm (
7.
78)
•Wei
ght
……………………………………….
.
.
.
.
.
.
.
1.1Kgs (2.43)
Power
•ACi
nput
…………………………………….
.
.
.......Power cord attached
•
Eur
opeanv
er
si
on…………………………………240V50Hz
Fuse
•Mai
n……………………………………………….
20mm Gl
as
s1AFastBl
ow
Control & Programming
•Dat
ai
nput
……………………………………….
.
.
Lock
i
ng3-pin XLR male socket
•Dat
aout
put
……………………………………….
Lock
i
ng3-pin XLR female socket
•Dat
api
nconf
i
gur
at
i
on………………………….
.
Pin 1 shield, pin1 (-), pin 3 (-)
•Pr
ot
ocol
s
………………………………………… DMX-512 UTSITT
•DMXc
hannel
s………………………………….
.
.
4
Download PDF