The IMPRESSA XS95/XS90 One Touch Manual

The IMPRESSA XS95/XS90 One Touch Manual
KE
Original instructions for use
Before using the machine read the instructions for use.
JURA Type 656
Important Safeguards
IMPORTANT SAFEGUARDS
These safeguards apply for machines with UL safety test (see rating
plate and chapter 10, ‘Technical data’).
Follow the basic safety
precautions
When using electrical appliances, basic safety precautions should
always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
Z Read all instructions.
Z Do not touch hot surfaces. Use handles or knobs.
Z To protect against fire, electric shock and injury to persons, do
not immerse cord, plugs, or body of machine in water or other
liquid.
Z Close supervision is necessary when any appliance is used by
or near children.
Z Unplug from outlet when not in use and before cleaning.
Allow to cool before putting or taking off parts, and before
cleaning the appliance.
Z Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
Z The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
Z Do not use outdoors.
Z Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
Z Do not place on or near a hot gas or electric burner, or in a
heated oven.
Z Always attach plug to appliance first, then plug cord into the
wall outlet. To disconnect, turn any control to ‘OFF’ then
remove plug from wall outlet.
Z Do not use appliance for other than intented use.
Z Use extreme caution when dispensing hot steam.
Z For household use only.
SAVE THESE INSTRUCTIONS
2
Important Safeguards
Special cord set instructions
a. A short power supply cord is provided to reduce the risk
resulting from becoming entangled in or tripping over a long
cord.
Your IMPRESSA has a 3-pin grounded plug.
b. Longer extension cords are available and may be used if care
is exercised in their use.
c. If an extension cord is used,
1. the marked electrical rating of the extension cord should be
at least as great as the electrical rating of the appliance,
and
2. if the appliance is of the grounded type, the extension
courd should be a grounding type 3-wire cord, and
3. the longer cord shall be arranged so that it will not drape
over the counter top or tabletop where it can be pulled on
by children or tripped over.
Z
Z
Z
As a safety feature, this plug will fit in a polarized outlet only
one way.
If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Do not modify the plug in any way or attempt to defeat this
safety feature.
Warning
To reduce the risk of fire or electric shock, do not remove any service
covers. No user serviceable parts inside. Repair should be done by
authorized personnel only.
Caution
This appliance is for household use. Any servicing other than cleaning and user maintenance should be performed by an authorized
service representative:
Z Do not immerse base in water or try to disassemble.
Z To reduce the risk of fire or electric shock, do not remove the
base. No user serviceable parts inside. Repair should be done
by authorized service personnel only.
Z Check voltage to be sure that the voltage indicated on the
name plate agreees with your voltage.
Z Never use warm or hot water to fill the water container! Use
cold water only.
3
Important Safeguards
Z
Z
NEVER DO
(or you will void your
warranty protection):
Z
Z
Z
Z
4
Keep your hands and the cord away from hot parts of the
appliance during operation.
Never clean with scouring powders or hard implements.
Never fill instant coffee, chocolate mix etc. into the grinder or
ground coffee funnel (grinder by-pass). It will damage the
functioning of the brewing chamber.
Never fill sugar coated coffee beans into the bean hopper. In
case of doubt, call your dealer.
Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).
Never do anything with the machine which is not described in
the User‘s Manual. In case of doubt, call your dealer.
Important Safeguards
5
Table of contents
Your IMPRESSA Xs95/Xs90 One Touch
IMPORTANT SAFEGUARDS
2
Control elements
8
Proper use
10
For your safety
10
14
The IMPRESSA XS95/XS90 One Touch Manual
Symbol description ......................................................................................................................................14
1 IMPRESSA XS95/XS90 One Touch
15
Connector System© ....................................................................................................................................16
JURA on the Internet ....................................................................................................................................16
Knowledge Builder .......................................................................................................................................16
2 Preparing and using for the first time
17
Setting up ......................................................................................................................................................17
Filling the water tank ...................................................................................................................................17
Bean container filling...................................................................................................................................17
First-time use ................................................................................................................................................18
Using and activating filter ..........................................................................................................................19
Determining and adjusting the degree of water hardness ..................................................................21
Adjusting grinder ........................................................................................................................................ 22
Switching on ................................................................................................................................................ 22
Switching off (standby) .............................................................................................................................. 23
3 Familiarising yourself with the control options
24
Preparation at the touch of a button.......................................................................................................24
One-off settings before and during preparation ...................................................................................25
Entering a permanent setting for the amount of water for a cup size..............................................26
Permanent settings in programming mode .......................................................................................... 27
Viewing information and maintenance status ......................................................................................29
4 Preparation at the touch of a button
30
Espresso ........................................................................................................................................................30
Coffee ............................................................................................................................................................30
Coffee à la Carte ...........................................................................................................................................31
Cappuccino....................................................................................................................................................31
Latte macchiato ........................................................................................................................................... 33
Pre-ground coffee .......................................................................................................................................34
Hot milk and milk foam ............................................................................................................................. 35
Hot water ..................................................................................................................................................... 37
6
Table of contents
5
Permanent settings in programming mode
38
Products ........................................................................................................................................................38
Energy-saving mode ..................................................................................................................................40
Time and weekday .......................................................................................................................................41
Programmable switch-on and switch-off time ......................................................................................42
Automatic switch-off ..................................................................................................................................43
Rinses ............................................................................................................................................................44
Unit amount of water / time format ........................................................................................................44
Language ......................................................................................................................................................45
6 Maintenance
46
Maintenance tips .........................................................................................................................................46
Rinsing the machine ...................................................................................................................................46
Changing the filter ...................................................................................................................................... 47
Cleaning the machine ................................................................................................................................49
Descaling the machine................................................................................................................................51
Rinsing the cappuccino frother ................................................................................................................ 53
Cleaning the cappuccino frother ..............................................................................................................54
Disassembling and rinsing the Professional Cappuccino Frother ......................................................56
Disassembling and rinsing the Easy Cappuccino Frother....................................................................56
Cleaning the bean container ..................................................................................................................... 57
Descaling the water tank ........................................................................................................................... 57
7 Display messages
58
8 Troubleshooting
60
9 Transport and environmentally neutral disposal
62
Transport / Emptying the system.............................................................................................................62
Disposal.........................................................................................................................................................62
10 Technical data
63
Index
64
JURA contact details / Legal information
68
7
Control elements
Control elements
8
1
9
2
10
11
3
12
13
4
14
15
5
6
7
Figure: IMPRESSA XS95 One Touch
1
2
3
4
5
6
7
8
Bean container cover
Bean container with aroma preservation
cover
Water tank with handle
Power switch and power cable
(back of machine)
Coffee grounds container
Cup platform
Drip tray
8
9
10
11
12
13
14
15
Fineness of grind switch
Cup tray
Cover of filler funnel for pre-ground coffee
Filler funnel for pre-ground coffee
Connector System©
for removable frothers
Professional Cappuccino Frother
Height-adjustable coffee spout
Hot water spout
Control elements
4
1
5
2
3
Front left
1
Display
2
Rotary Switch cover
3
f Rotary switch
Q On/off button
c Maintenance button
i 1 Espresso button
4 2 Espressi button
o 1 Coffee button
d 2 Coffees button
e Coffee à la Carte button
v Pre-ground coffee button
Front right
4
ö Selector switch
5
Professional Cappuccino Frother
6 Easy Cappuccino Frother
a Hot water portion symbol
m Hot water symbol
p Cappuccino button
z Milk portion symbol
n Milk symbol
q Latte Macchiato button
The Connector System© permits the use of different frothers. These are available from stockists.
5
6
9
Important information
Proper use
The machine is designed and intended for commercial use. It should only be used for coffee preparation and to heat milk and water. Use for any
other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility
for the consequences of improper use.
Before using the machine always carefully read and
comply with all these instructions. Keep this manual close to the IMPRESSA and, if appropriate, pass
it on to the next user.
For your safety
10
Please read and note carefully the following important safety information.
By doing this, you can avoid the life-threatening
danger of electric shock:
Z Never use a machine which has been damaged or with a defective power cable.
Z For information on what to do in case of damage, for example if there is a smell of burning,
unplug the machine immediately from the
mains supply and contact the JURA service
centre.
Z If the power cable for this machine is damaged, it must be repaired either directly by
JURA or by a JURA approved service centre.
Z Make sure that the IMPRESSA and the power
cable are not located close to hot surfaces.
Z Be careful to ensure that the power cable does
not get caught and does not rub against sharp
edges.
Important information
Z
Never open and repair the machine yourself.
Do not modify the machine in any way that is
not described in the IMPRESSA Manual. The
machine contains live parts. If opened, there is
a danger of serious injury. Repairs may only be
carried out by JURA approved service centres,
using original spare parts and accessories.
There is a risk of scalds or burns on the spouts or in
the nozzle:
Z Place the machine out of the reach of children.
Z Do not touch any hot parts. Use the handles
provided.
Z Be careful to ensure that the appropriate nozzle is installed and clean. The nozzle or parts of
the nozzle might come off if the parts are not
assembled correctly or a blockage occurs.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
Z Never allow the power cable to loosely hang
down. The power cable can be tripped over or
damaged.
Z Protect your IMPRESSA from environmental
influences such as rain, frost and direct sunlight.
Z Do not put the IMPRESSA, cable or connections in water.
Z Do not put the IMPRESSA or any individual
parts in the dishwasher.
11
Important information
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
12
Turn your IMPRESSA off at the power switch
before starting any cleaning operation. Always
wipe your IMPRESSA with a damp cloth rather
than a wet one, and protect it from prolonged
water splash.
Do not set up the IMPRESSA anywhere where
a jet of water may be used.
Only connect the machine to a power supply
in accordance with the information on the rating plate. The rating plate is located on the
underside of your IMPRESSA. Further technical
data is given in Chapter 10 ‘Technical Data’.
Use only original JURA care products. Use of
accessories that are not explicitly recommended by JURA could damage the IMPRESSA.
Do not use any coffee beans treated with additives or caramelised coffee beans.
Always fill the water tank with cold, fresh mains
water.
If you will be absent for an extended period,
turn the machine off and unplug.
Children may not clean or service the machine
unless supervised by a responsible person.
Do not allow children to play with the machine.
Keep children under the age of 8 away from
the machine, or supervise them constantly.
Children aged 8 and over may only operate
the machine without supervision if they have
been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.
Important information
People, including children, who
Z do not have the physical, sensory or mental
capabilities to use the machine safely or
Z are inexperienced or lack knowledge in how to
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it correctly.
Safe handling of the CLARIS filter cartridges:
Z CLARIS filter cartridges should be kept out of
the reach of children.
Z Store them dry in the sealed package.
Z Protect them from heat and direct sunlight.
Z Do NOT use damaged CLARIS filter cartridges.
Z Do NOT open CLARIS filter cartridges.
13
The IMPRESSA XS95/XS90 One Touch Manual
The IMPRESSA XS95/XS90 One Touch Manual
You are holding the manual for your IMPRESSA XS95/XS90 One
Touch in your hand. It will help you to familiarize yourself with your
IMPRESSA safely and quickly and teach you the full range of facilities
it offers.
Chapter 2, ‘Preparing and using your IMPRESSA for the first time’,
explains step-by-step how to set up and prepare the IMPRESSA.
Chapter 3, ‘Familiarising yourself with the control options’ is important for you to read as you are familiarising yourself with your
IMPRESSA. It invites you to actively explore all the different coffee
experiences that it offers.
All the other chapters are intended to help you when you have a specific query.
If you use the IMPRESSA XS95/XS90 One Touch Manual, you will
become a master at preparing exciting coffee specialities, you will
be a Barista!
@ You can download the short operating instructions for your
machine from the JURA website (www.jura.com).
Symbol description
Warnings
CAUTION
CAUTION
Always take note of any information marked with the CAUTION or WARNING symbol.
The signal word WARNING points out potential risk of serious injury, and the signal
word CAUTION potential risk of slight injury.
The CAUTION symbol is used to draw attention to circumstances which could cause
the machine to become damaged.
Symbols used
14
E
Information and tips to make things easier for you as you use your IMPRESSA.
@
References to the online JURA website, where you can find interesting further information: www.jura.com.
T
Prompt to take action. This symbol means that you are being prompted to perform
some action.
1 IMPRESSA XS95/XS90 One Touch
1
IMPRESSA XS95/XS90 One Touch
Coffee that fulfils your
wildest dreams
Anyone thinking of coffee today no longer only conjures up visions
of espresso and café crème, but also of contemporary coffee specialities such as latte macchiato or cappuccino. This development also
calls for a solution for small shops, offices and catering establishments. All demands are more than met by the IMPRESSA XS95/XS90
One Touch which prepares twelve different products – including the
trend beverage latte macchiato – at the touch of a button. The customary JURA portability is not, however, affected by this versatility,
and with its compact design and low weight of 13.8 kg the machine
can be placed just where it is needed.
Z
Design: A great deal of attention was paid to the machine
design during its development to ensure that it looks just as
good as the freshly prepared coffee specialities accentuated
by the cup lighting. Control elements such as the selector
switch with the pictograms and background lighting, the
Rotary Switch and the graphic display not only make an outstanding visual impression, but effectively lead the way
through the simple navigation.
Z
Ecological intelligence: The IMPRESSA XS95/XS90 One Touch
helps you protect the environment and save your money.
With the energy-saving mode (Energy Save Mode, E.S.M.©)
the machine requires up to 60% less energy and, if required,
automatically switches to standby mode after a certain time.
If it is not used for prolonged periods, for example during holidays, the machine can be simply disconnected from the
mains by means of the integrated mains switch.
Z
Time management: The enjoyment of coffee specialities has
become a regular part of our everyday life. The IMPRESSA
XS95/XS90 One Touch does full justice to this fact, and with its
integrated time management system ensures that no (coffee)
highlight is forgotten. The machine automatically switches on
and off at the programmed time, ensuring that your coffee is
ready when you want it – naturally only on the weekdays you
have chosen.
15
1 IMPRESSA XS95/XS90 One Touch
Z
All-round coffee solution: Together with an optionally available cup warmer, a matching milk cooler or a vending interface, the machine can be extended module-by-module to create an all-round coffee solution and can also be optimised for
self-service applications. Machine operation is then also easy
for inexperienced users, as the use of the control elements is
intuitive and the programming buttons are discreetly concealed behind a hinged panel. If necessary, these can even be
blocked.
Connector System©
The Connector System© permits the use of different cappuccino
frothers:
Z Professional Cappuccino Frother
U Cappuccino / latte macchiato
U Hot milk
Z Easy Cappuccino Frother
U Cappuccino / latte macchiato
JURA on the Internet
Visit us on the Internet.
@ At www.jura.com you will find interesting and up-to-date
information on your IMPRESSA and on every aspect of coffee.
Knowledge Builder
You can familiarize yourself with your IMPRESSA XS95/XS90 One
Touch in a fun way on the PC.
@ The Knowledge Builder awaits you at www.jura.com. The
interactive assistant, LEO, will support you and explain the
benefits of and how to use your IMPRESSA.
16
2 Preparing and using your IMPRESSA for the first time
2 Preparing and using for the first time
This chapter provides you with the information you need to use your
IMPRESSA without any problems. You will prepare your IMPRESSA
step-by-step for your first coffee experience.
Setting up
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transportation.
When setting up your IMPRESSA, please note the following:
Z Set the IMPRESSA down on a horizontal surface that is not
sensitive to water.
Z Choose a spot for your IMPRESSA which is protected against
overheating. Ensure that the ventilation slots are not covered.
Filling the water tank
CAUTION
To enjoy perfect coffee we recommend changing the water every
day.
Milk, mineral water or other liquids can damage the water tank or
the machine.
T Only fill the water tank with fresh, cold water.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert.
Bean container filling
CAUTION
The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
Coffee beans which have been treated with additives (e.g. sugar),
pre-ground or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to refill the bean
container.
T Open the cover of the bean container and remove the aroma
preservation cover.
T Remove any dirt or foreign objects inside the bean container.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
17
2 Preparing and using your IMPRESSA for the first time
First-time use
WARNING
If the machine is operated with a defective power cable, there is a
danger of electric shock.
T Never use a machine which has a defective power cable.
Precondition: The water tank and bean container are full.
T Insert the mains plug into a power socket.
3 T Switch on the IMPRESSA using the power switch on the back
of the machine.
The on/off button Q lights up (standby).
Q T Press the on/off button to switch the IMPRESSA on.
The pre-set language appears on the display.
T Open the cover of the Rotary Switch.
g T Turn the Rotary Switch until the desired language is displayed. For Example: LANGUAGE ENGLISH
k T Press the Rotary Switch to confirm the language.
CONFIRMED √ appears briefly on the display to confirm
the setting.
TIME --:-g T Turn the Rotary Switch to set the hour.
TIME 12:00 (Example)
k T Press the Rotary Switch to confirm the hour setting.
TIME 12:00
g T Turn the Rotary Switch to set the minutes.
TIME 12:45 (Example)
k T Press the Rotary Switch to confirm the minute setting.
CONFIRMED √ appears briefly on the display.
WEEKDAY MONDAY
g T Turn the Rotary Switch to set the weekday.
WEEKDAY WEDNESDAY (Example)
k T Press the Rotary Switch to confirm the setting.
CONFIRMED √ appears briefly on the display.
FILL SYSTEM / PRESS RINSE, the maintenance
button c lights up.
18
2 Preparing and using your IMPRESSA for the first time
T Place a receptacle under the hot water spout and another
under the frother.
c T Press the maintenance button.
SYSTEM FILLS, the system fills up with water and the
maintenance button flashes. A small amount of water flows
from the frother and the hot water spout.
This operation stops automatically. WELCOME TO JURA
appears on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
E After first-time use do not disconnect the IMPRESSA from the
power supply for 24 hours to ensure that it is in the optimum
operating condition.
E When a coffee speciality has been prepared for the first time,
it is possible that FILL BEANS is shown on the display as
the grinder has not yet been completely filled with coffee
beans. In this case prepare a different coffee speciality.
E If you have not been able to use the machine for the first time
correctly and fully, contact customer support in your country
(see Chapter ‘JURA contact details / Legal information’).
Using and activating
filter
Your IMPRESSA no longer has to be descaled if you are using CLARIS
filter cartridges.
@ You can also try out the ‘Using and activating filter’ operation
online. Visit the Knowledge Builder at www.jura.com.
E Perform the ‘Insert and activate filter’ operation without interruptions. This will ensure that your IMPRESSA always produces its best.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears on the display.
19
2 Preparing and using your IMPRESSA for the first time
g T Turn the Rotary Switch until FILTER NO is displayed.
k T Press the Rotary Switch to enter the programme item.
FILTER NO
g T Turn the Rotary Switch until FILTER YES is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display to confirm
the setting.
INSERT FILTER / PRESS RINSE, the maintenance
button c lights up.
T Remove a CLARIS filter cartridge and the filter cartridge
extension from the Welcome Pack.
T Fit the extension on top of the filter cartridge.
T Remove the water tank and empty it.
T Lift the cartridge holder and insert the filter cartridge into
the water tank, applying slight pressure.
T Close the cartridge holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert.
T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water flows out of the frother.
E You can interrupt rinsing of the filter at any time by pressing
any button.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml.
COFFEE READY appears on the display. The filter is now
activated.
20
2 Preparing and using your IMPRESSA for the first time
Determining and
adjusting the degree of
water hardness
The harder the water is, the more frequently the IMPRESSA needs to
be descaled. It is therefore important to adjust the water hardness.
The water hardness can be adjusted on a continuous scale between
1 °dH and 30 °dH. This can also be deactivated, which means that
the IMPRESSA will not let you know when it has to be descaled.
E However, if you are using the CLARIS filter cartridge and have
activated it, you will not be able to adjust the water hardness.
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
T Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
T Wait for about one minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
You can now adjust the water hardness.
Example: To change the water hardness from 16°dH to 25°dH,
proceed as follows:
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the rotary switch until HARDNESS 16°dH is
displayed.
k T Press the Rotary Switch to enter the programme item.
16°dH
g T Turn the Rotary Switch until 25°dH is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
HARDNESS 25°dH
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY is shown on the display.
21
2 Preparing and using your IMPRESSA for the first time
Adjusting grinder
CAUTION
You can adjust the grinder continuously to suit the roast of your
coffee.
If you adjust the fineness of grind when the grinder is not operating,
the grinding wheel could be damaged.
T Only adjust the fineness of grind when the grinder is running.
The fineness of grind setting is correct if the coffee flows regularly
from the coffee spout. A fine, thick crema is also formed.
Our recommendations:
Z Select a fine setting for a light roast.
U If the fineness of grind setting is too fine, the coffee only
drips from the coffee spout.
Z
Select a coarse setting for a darker roast.
U If the fineness of grind is too coarse, the coffee flows too
quickly from the coffee spout.
Example: To change the fineness of grind during coffee preparation,
proceed as follows:
T Open the cover of the bean container.
T Place a cup under the coffee spout.
o T Press the 1 Coffee button.
The grinder starts and 1 COFFEE is displayed.
T Turn the fineness of grind switch to the desired position
while the grinder is running.
The coffee will be prepared and the fineness of grind is
adjusted.
Switching on
22
When the IMPRESSA is switched on, a prompt for the rinse operation
automatically appears which is initiated by pressing the maintenance button.
2 Preparing and using your IMPRESSA for the first time
This setting can be changed in programming mode so that the
machine automatically activates the switch-on rinse (see Chapter 5
‘Permanent settings in programming mode – Rinses’).
Precondition: Your IMPRESSA is switched on at the power switch
and the on/off button Q is illuminated (standby).
Q T Press the on/off button to switch the IMPRESSA on.
WELCOME TO JURA appears briefly on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
Switching off (standby)
When you switch your IMPRESSA off, the spouts with which a coffee
speciality or milk have been prepared are rinsed.
T Place a receptacle under the coffee spout and the frother.
Q T Press the on/off button.
MACHINE RINSING appears on the display, and the
coffee spout is rinsed.
SPOUT RIGHT / PRESS RINSE
c T Press the maintenance button.
MACHINE RINSING, the right coffee spout is rinsed.
E When you prepare a milk product, but have not performed
cappuccino cleaning, CLEAN CAPPUCCINO appears and
the maintenance button c lights up. For ten seconds you can
start the ‘Clean cappuccino frother’ procedure by pressing the
maintenance button c.
The IMPRESSA is switched off (standby mode), and the
on/off button Q lights up.
E When your IMPRESSA is switched off, a hissing noise may be
audible. This is normal and does not have any effect on the
machine.
23
3 Familiarising yourself with the control options
3 Familiarising yourself with the control options
With the IMPRESSA, you can prepare an excellent coffee or milk speciality at the touch of a button. You also have the option of adjusting
the coffee strength and temperature, as well as the amount of water
to your personal taste.
This chapter will allow you to become familiar with all control
options with the aid of examples. To familiarise yourself with your
IMPRESSA, we recommend that you make a point of actively trying
the facilities described in this chapter. You will find this is well worthwhile.
Learn how to perform the following:
Z Preparation at the touch of a button
Z One-off settings before and while your drink is being prepared
Z Adjusting the default amount of water to suit the cup size
Z Permanent settings in programming mode
E You can stop the machine at any time while a coffee or milk
speciality or hot water is being prepared. To do this, press any
button.
@ If you prefer to familiarise yourself with your IMPRESSA in a
fun way on the computer, the interactive Knowledge Builder
tutorial programme can be found on the Internet at
www.jura.com.
Preparation at the
touch of a button
Prepare your favourite coffee speciality at the touch of a button.
All coffee specialities are prepared following this model.
Example: This is how to prepare one coffee.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
o T Press the 1 Coffee button.
1 COFFEE and the pre-set coffee strength is displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
24
E To prepare 2 coffees, place two cups under the coffee spout
and press the 2 Coffees button d.
3 Familiarising yourself with the control options
One-off settings before
and during preparation
It is possible to make various settings before and during preparation.
These one-off settings are always follow the same model and are not
stored.
Changing the coffee
strength before preparation
The coffee strength of Coffee à la Carte can be changed before
preparation. The following coffee strength options can be selected:
Z ö (xmild)
Z öö (mild)
Z ööö (normal)
Z öööö (strong)
Z ööööö (xstrong)
Example: Proceed as follows to to prepare a strong cup of Coffee à
la Carte.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
T Open the cover of the Rotary Switch.
e T Press the Coffee à la Carte button.
A LA CARTE and the pre-set coffee strength is displayed.
g T Turn the Rotary Switch until A LA CARTE öööö is displayed.
k T Press the Rotary Switch while A LA CARTE öööö is
displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
appears on the display. COFFEE READY is then displayed.
Changing the amount of
water during preparation
The pre-set amount of water of all coffee products can be changed
during the brewing operation by turning the Rotary Switch.
Example: Proceed as follows to prepare a 110 ML cup of coffee.
Precondition: COFFEE READY is displayed.
25
3 Familiarising yourself with the control options
T Place a cup under the coffee spout.
T Open the cover of the Rotary Switch.
o T Press the 1 Coffee button.
1 COFFEE and the pre-set coffee strength is displayed.
The brewing operation starts and the coffee flows into the
cup.
g T Turn the Rotary Switch during the brewing operation until
1 COFFEE / 110 ML is displayed.
The set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
Entering a permanent
setting for the amount
of water for a cup size
It is easy to make permanent settings for the amount of water for all
coffee specialities, cappuccino, latte macchiato, a portion of hot
water and portion of milk according to the cup size. As in the following example, adjust the amount of water once. Every time you prepare a drink in the future, this amount of water will be dispensed.
Making the permanent settings for the amount of water for the
respective cup size always follows this model.
Example: To make permanent settings for the amount of water for
an espresso, proceed as follows:
Precondition: COFFEE READY is displayed.
T Place an espresso cup under the coffee spout.
i T Press and hold the 1 Espresso button.
1 ESPRESSO and the coffee strength is displayed.
i T Hold the Espresso button down until ENOUGH COFFEE?
appears.
i T Release the 1 Espresso button.
Coffee preparation will start and the espresso will flow into
the cup.
T Press any button as soon as enough espresso has flowed
into the cup.
Preparation stops automatically. CONFIRMED w appears
briefly on the display. The set amount of water for an
espresso will be permanently stored. COFFEE READY is
displayed.
26
E You can alter these settings at any time by repeating the
above procedure.
3 Familiarising yourself with the control options
Permanent settings in
programming mode
You can easily adjust your IMPRESSA to your personal coffee blends
and specialities. You can navigate through the easy-to-understand
programme steps and make permanent settings simply by turning
and pressing the Rotary Switch.
You can make the following permanent settings with the Rotary
Programme item
Subitem
Explanation
MAINTENANCE CLEAN CAPPUCCINO,
RINSE MACHINE,
RINSE CAPPUCCINO,
CLEAN MACHINE,
DECALCIFY
MACHINE,
CHANGE FILTER
T Select the desired maintenance
programme.
If no action is taken, programming mode
is exited in the MAINTENANCE programme
item automatically after approx. five seconds.
PRODUCTS
T Select your settings for the coffee and milk
specialities and hot water.
FILTER
FILTER YES
FILTER NO
T Indicate whether you operate your IMPRESSA
with or without a CLARIS filter cartridge.
HARDNESS
HARDNESS
INACTIVE,
1°dH – 30°dH
T Adjust the water hardness.
(is only displayed
when the filter is
not activated)
ECONOMY MODE SAVE NO,
SAVE LEVEL 1,
SAVE LEVEL 2
TIME
--:--, WEEKDAY
T Select an energy-saving mode.
T Set the time and weekday.
T Set the switch-on and switch-off time
individually for each weekday.
UNIT ON/OFF
OFF AFTER
OFF AFTER -- H,
0.5 H – 15 H
T Set the number of hours after which the
IMPRESSA should switch off automatically.
RINSES
INIT RINSE,
CAPP RINSE
T Set whether the switch-on rinse should be
started manually or automatically.
T Set whether the prompt for cappuccino
rinsing should be started immediately or
10 minutes afterpreparation of a milk speciality.
27
3 Familiarising yourself with the control options
Programme item
Subitem
Explanation
T Keep track of all prepared coffee and milk
specialities and view the maintenance status.
INFORMATION
SETTINGS
ML/OZ,
24HRS/AM PM
T Select the unit of the amount of water and
the time format.
LANGUAGE
T Select the desired language.
EXIT
T Exit programming mode.
Switch:
Settings in programming mode always follow the same model.
Example: To change the strength of one espresso from ööö
(normal) to öööö (strong).
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
k T Press the Rotary Switch to enter the programme item.
SELECT PRODUCT
E Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
i T Press the 1 Espresso button.
WATER 45 ML
g T Turn the Rotary Switch until AROMA ööö is displayed.
k T Press the Rotary Switch to enter the programme item.
NORMAL ööö
g T Turn the Rotary Switch until STRONG öööö is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
AROMA öööö
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
SELECT PRODUCT
28
3 Familiarising yourself with the control options
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
PRODUCTS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Viewing information
and maintenance
status
Under the programme item INFORMATION you can query the
following information:
Z Number of the prepared coffee and milk specialities and hot
water
Z Maintenance status and number of maintenance programmes
performed (cleaning, descaling, filter change)
Z Number of performed cappuccino cleaning operations
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Press the Rotary Switch until MAINTENANCE appears.
g T Turn the Rotary Switch until INFORMATION is displayed.
k T Press the Rotary Switch to enter the programme item.
TOTAL, the sum of all prepared coffee and milk specialities
is displayed.
g T Turn the Rotary Switch for further information.
E The respective maintenance status can also be displayed in
addition to the number of performed maintenance programmes. The bar shows the current maintenance status.
When the bar is filled completely, your IMPRESSA will request
the respective maintenance programme.
k T Press the Rotary Switch to exit the programme item.
INFORMATION
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
29
4 Preparation at the touch of a button
4 Preparation at the touch of a button
In this chapter you will find out how to prepare coffee and milk specialities and hot water without making further settings.
E You can stop the machine at any time while a coffee or milk
product or hot water is being prepared. To do this, press any
button.
E During preparation, you can change the pre-set amount of
water by turning the Rotary Switch.
@ You can also try out the preparation of coffee specialities
online. Visit the Knowledge Builder at www.jura.com.
Espresso
The classic coffee drink from Italy. There is a definite crema on the
surface of the espresso.
Example: This is how to prepare one espresso.
Precondition: COFFEE READY is displayed.
T Place an espresso cup under the coffee spout.
i T Press the 1 Espresso button.
1 ESPRESSO and the pre-set coffee strength are displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
E To prepare two espressi place two cups under the coffee
spout and press the 2 Espressi button 4.
Coffee
Example: This is how to prepare one coffee.
Precondition: COFFEE READY is displayed.
T Place a coffee cup under the coffee spout.
o T Press the 1 Coffee button.
1 COFFEE and the pre-set coffee strength are displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
E To prepare 2 coffees, place two cups under the coffee spout
and press the 2 Coffees button d.
30
4 Preparation at the touch of a button
Coffee à la Carte
The coffee strength of Coffee à la Carte can be changed before
preparation.
Example: Proceed as follows to prepare a strong (öööö) cup of
Coffee à la Carte.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
T Open the cover of the Rotary Switch.
e T Press the Coffee à la Carte button.
A LA CARTE ö
g T Turn the Rotary Switch until A LA CARTE öööö is
displayed.
k T Press the Rotary Switch while A LA CARTE öööö is
displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
appears on the display. COFFEE READY is then displayed.
Cappuccino
Cappuccino with the
Professional Cappuccino
Frother
Your IMPRESSA prepares a cappuccino at the touch of a button. It is
not necessary to move the cup.
Precondition: COFFEE READY is displayed.
T Take the protective cover off the Professional Cappuccino
Frother.
T Attach the milk pipe to the frother.
T Connect the other end to an original JURA milk container or
immerse it directly into the milk.
T Place a cup under the frother.
T Turn the selection lever of the frother to the milk foam
position p.
p T Press the Cappuccino button.
CAPPUCCINO and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when the pre-set amount of milk is reached.
31
4 Preparation at the touch of a button
Coffee preparation then begins. The pre-set amount of
water flows into the cup.
Preparation stops automatically. ENJOY appears on the
display. COFFEE READY is then displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Cappuccino with the Easy
Cappuccino Frother
Precondition: COFFEE READY is displayed.
T Take the protective cover off the Easy Cappuccino Frother.
T Attach the milk pipe to the frother.
T Connect the other end to an original JURA milk container or
immerse it directly into the milk.
T Place a cup under the frother.
p T Press the Cappuccino button.
CAPPUCCINO and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when the pre-set amount of milk is reached.
Coffee preparation then begins. The pre-set amount of
water flows into the cup.
Preparation stops automatically. ENJOY appears on the
display. COFFEE READY is then displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
32
4 Preparation at the touch of a button
Latte macchiato
Latte macchiato with the
Professional Cappuccino
Frother
Your IMPRESSA prepares a latte macchiato at the touch of the
button. It is not necessary to move the glass.
Precondition: COFFEE READY is displayed.
T Take the protective cover off the Professional Cappuccino
Frother.
T Attach the milk pipe to the frother.
T Connect the other end to an original JURA milk container or
immerse it directly into the milk.
T Place a glass under the frother.
T Turn the selection lever of the frother to the milk foam
position p.
q T Press the Latte Macchiato button.
LATTE MAC. and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when pre-set amount of milk is reached.
E A brief pause follows during which the hot milk separates from
the milk foam. This enables the formation of the typical layers
of a latte macchiato. The duration of this pause can be defined
in programming mode.
Coffee preparation then begins. The pre-set amount of
water flows into the glass. Preparation stops automatically.
ENJOY appears on the display. COFFEE READY is then
displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
33
4 Preparation at the touch of a button
Latte macchiato with the
Easy Cappuccino Frother
Precondition: COFFEE READY is displayed.
T Take the protective cover off the Easy Cappuccino Frother.
T Attach the milk pipe to the frother.
T Connect the other end to an original JURA milk container or
immerse it directly into the milk.
T Place a glass under the frother.
q T Press the Latte Macchiato button.
LATTE MAC. and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when pre-set amount of milk is reached.
E A brief interval follows during which the hot milk separates
from the milk foam. This enables the formation of the typical
layers of a latte macchiato. The duration of this interval can be
defined in programming mode.
Coffee preparation then begins. The pre-set amount of
water flows into the glass. Preparation stops automatically.
ENJOY appears on the display. COFFEE READY is then
displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Pre-ground coffee
You can choose a second coffee blend, for example decaffeinated
coffee, with the filler funnel for pre-ground coffee.
E Never add more than two level measuring spoons of preground coffee.
E Use pre-ground coffee which is not ground too finely. Very
fine coffee can block up the system so that the coffee only
comes out in drips.
E If you did not fill the machine with a sufficient amount of preground coffee, NOT ENOUGH PRE-GROUND is displayed
and the IMPRESSA stops operation.
34
4 Preparation at the touch of a button
All coffee specialities with pre-ground coffee are prepared following
this model.
Example: This is how to prepare a cup of coffee using pre-ground
coffee.
T Place a cup under the coffee spout.
T Open the cover of the filler funnel for pre-ground coffee.
T Open the cover of the Rotary Switch.
v T Press the Pre-ground coffee button.
FILL PRE-GROUND / COFFEE READY
T Place one level measuring spoon of pre-ground coffee into
the filler funnel.
T Close the cover of the filler funnel for pre-ground coffee.
o T Press the 1 Coffee button.
1 COFFEE, the pre-set amount of water flows into the cup.
Preparation stops automatically. ENJOY appears on the
display. COFFEE READY is then displayed.
Hot milk and milk
foam
Foaming and heating milk
with the Professional
Cappuccino Frother
There are two options for preparing hot milk or milk foam:
Z Milk portion z
U The preset quantity of milk is then prepared.
Z Milk n
U Milk is prepared until preparation is interrupted by pressing
any button.
Precondition: COFFEE READY is displayed.
T Take the protective cover off the frother.
T Attach the milk pipe to the frother.
T Connect the other end to an original JURA milk container or
immerse it directly into the milk.
35
4 Preparation at the touch of a button
T Place a cup under the frother.
T Turn the selection lever of the frother to the milk foam
position p.
E If you want to heat the milk, set the selection lever of the
frother to the milk position t.
ö T With the selector switch select the milk portion symbol z.
ä T Press the selector switch.
MILK, the milk foam is being prepared. Preparation stops
automatically when the pre-set amount of milk is reached.
COFFEE READY is shown on the display.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Foaming milk with the Easy
Cappuccino Frother
Precondition: COFFEE READY is displayed.
T Take the protective cover off the frother.
T Attach the milk pipe to the frother.
T Connect the other end to an original JURA milk container or
immerse it directly into the milk.
T Place a cup under the frother.
ö T With the selector switch select the milk portion symbol z.
ä T Press the selector switch.
MILK, the milk foam is being prepared. Preparation stops
automatically when the pre-set amount of milk is reached.
COFFEE READY is shown on the display.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
36
4 Preparation at the touch of a button
Hot water
Hot water can be prepared in two ways:
Z Hot water portion a
U The pre-set amount of water flows into the cup.
Z Hot water m
U Water flows out of the hot water spout until preparation is
interrupted by pressing any button.
The following temperatures can be selected for preparing hot
water:
Z Low
Z Normal
Z X high
CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Example: This is how to prepare a portion of hot water.
Precondition: COFFEE READY is displayed.
T Place a cup under the hot water spout.
ö T Use the selector switch to select the hot water portion
symbol a.
ä T Press the selector switch.
TEMPERATURE and the pre-set temperature are displayed.
E By pressing the selector switch several times (within approx.
2 seconds) you can set the temperature to your individual
preference. This setting is not saved.
HOT WATER, the pre-set amount of water flows into the
cup. Preparation stops automatically. COFFEE READY
appears on the display.
37
5 Permanent settings in programming mode
5 Permanent settings in programming mode
Products
With the PRODUCTS programme item you can enter individual
settings for all coffee and milk specialities as well as hot water.
The following permanent settings can be made:
Product
Amount
Coffee strength
Temp.
1 Espresso,
1 Coffee
25 ML – 240 ML
ö (xmild),
NORMAL, HIGH
öö (mild),
ööö (normal),
öööö (strong),
ööööö (xstrong)
2 Espressi,
2 Coffees
25 ML – 240 ML
Coffee à la Carte
25 ML – 240 ML
Cappuccino,
Latte macchiato
Amount of milk:
3 SEC – 120 SEC
Pause: 0 SEC – 60 SEC
Amount of water:
25 ML – 240 ML
Milk portion
3 SEC – 120 SEC
–
NORMAL, HIGH
–
NORMAL, HIGH
(per cup)
ö (xmild),
NORMAL, HIGH
öö (mild),
ööö (normal),
öööö (strong),
ööööö (xstrong)
–
–
–
–
Hot water portion 25 ML – 450 ML
–
LOW, NORMAL, X HIGH
Hot water
–
LOW, NORMAL, X HIGH
Milk
–
–
E The products which are selected with the selector switch can
be individually set to inactive. This means that the respective
symbols are not visible and preparation is not possible.
Permanent settings in programming mode always follow the same
model.
Example: Proceed as follows to change the amount of milk of latte
macchiato from 16 SEC to 20 SEC, the pause from 30 SEC
to 40 SEC and the amount of water from 45 ML to 40 ML.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
38
5 Permanent settings in programming mode
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
k T Press the Rotary Switch to enter the programme item.
SELECT PRODUCT
E Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
q T Press the Latte Macchiato button.
COFFEE 45 ML
k T Press the Rotary Switch to enter the programme item.
COFFEE 45 ML
g T Turn the Rotary Switch until COFFEE 40 ML is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
COFFEE 40 ML
g T Turn the Rotary Switch until MILK 16 SEC is displayed.
k T Press the Rotary Switch to enter the programme item.
MILK 16 SEC
g T Turn the Rotary Switch until MILK 20 SEC is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
MILK 20 SEC
g T Turn the Rotary Switch until PAUSE 30 SEC is displayed.
k T Press the Rotary Switch to enter the programme item.
PAUSE 30 SEC
g T Turn the Rotary Switch until PAUSE 40 SEC is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
PAUSE 40 SEC
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
SELECT PRODUCT
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
PRODUCTS
39
5 Permanent settings in programming mode
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Resetting the products to
works settings
You can reset the values of all products as well as cappuccino and
latte macchiato individually to the works setting.
Example: Proceed as follows to reset the values of 1 Espresso to the
works setting.
Precondition: The IMPRESSA is switched off (standby).
T Open the cover of the Rotary Switch.
T Press the Rotary Switch and the 1 Espresso button for two
seconds at the same time until 1 ESPRESSO OK
appears.
The values of 1 Espresso are then reset to the works setting.
The IMPRESSA is switched off (standby).
Energy-saving mode
40
With the energy-saving mode (Energy Save Mode, E.S.M.©) the
machine requires up to 60% less energy. You can set various energysaving modes on your IMPRESSA:
Z SAVE NO
U Your IMPRESSA is continuously ready for use.
U All coffee and milk products, as well as hot water, can be
prepared without having to wait.
Z SAVE LEVEL 1
U Your IMPRESSA is only continuously ready for use for coffee
products and hot water.
U The machine has to heat up before milk preparation.
Z SAVE LEVEL 2
U Approx. 5 minutes after the last preparation the IMPRESSA
switches to the energy-saving temperature and is not ready
for use.
U Before coffee, hot water or milk can be prepared, the machine
has to heat up.
Example: Proceed as follows to change the energy-saving mode
from SAVE NO to SAVE LEVEL 1.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
5 Permanent settings in programming mode
g T Turn the Rotary Switch until ECONOMY MODE - is displayed.
k T Press the Rotary Switch to enter the programme item.
SAVE NO
g T Turn the Rotary Switch until SAVE LEVEL 1 is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
ECONOMY MODE 1
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Time and weekday
You already set the time and weekday when you used the machine
for the first time.
Example: To change the time from 08:45 to 09:50, proceed
as follows.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until TIME 08:45 is displayed.
k T Press the Rotary Switch to enter the programme item.
TIME 08:45
T Turn the Rotary Switch until TIME 09:45 is displayed.
T Press the Rotary Switch to confirm the hour setting.
T Turn the Rotary Switch until TIME 09:50 is displayed.
T Press the Rotary Switch to confirm the minute setting.
CONFIRMED w appears briefly on the display.
WEEKDAY MONDAY (Example)
k T Press the Rotary Switch to confirm the weekday setting.
CONFIRMED √ appears briefly on the display.
g
k
g
k
TIME 09:50
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
41
5 Permanent settings in programming mode
Programmable switchon and switch-off time
The programmable switch-on and switch-off time can only be set
when the time has been set.
The following settings can be made in the UNIT ON/OFF menu
item:
Z UNIT ON: Set the required switch-on time.
Z MACH. OFF: Set the required switch-off time.
Z ON/OFF: Set the weekdays on which IMPRESSA should
switch on and off automatically.
E The programmable switch-on only works when the machine
is switched on at the power switch (standby).
Example: Proceed as follows to set the programmable switch-on
time to 07:30 and stipulate that your IMPRESSA does not switch
on automatically on Sundays.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until UNIT ON/OFF is displayed.
k T Press the Rotary Switch to enter the programme item.
UNIT ON --:-k T Press the Rotary Switch to enter the programme item.
UNIT ON --:-g T Turn the Rotary Switch until UNIT ON 07:00 is displayed.
k T Press the Rotary Switch to confirm the hour setting.
g T Turn the Rotary Switch until UNIT ON 07:30 is displayed.
k T Press the Rotary Switch to confirm the minute setting.
CONFIRMED w appears briefly on the display.
UNIT ON 07:30
42
g T Turn the Rotary Switch until ON/OFF / MON YES is displayed.
k T Press the Rotary Switch to enter the programme item.
ON/OFF / MON YES
g T Turn the Rotary Switch until ON/OFF / SUN YES is displayed.
k T Press the Rotary Switch to enter the programme item.
ON/OFF / SUN YES
5 Permanent settings in programming mode
g T Turn the Rotary Switch until ON/OFF / SUN NO is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
ON/OFF / SUN NO
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
ON/OFF / MON YES
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
UNIT ON/OFF
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the last action on
the machine.
E The programmable switch-off time can be adjusted between
0.5 and 15 hours or deactivated.
Example: Proceed as follows to change the automatic switch-off
time from 1 H to 2 H.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until OFF AFTER 1 H is displayed.
k T Press the Rotary Switch to enter the programme item.
OFF AFTER 1 H
g T Turn the Rotary Switch until OFF AFTER 2 H is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
OFF AFTER 2 H
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
43
5 Permanent settings in programming mode
Rinses
You can set whether the switch-on rinse should be started manually
or automatically.
You can set whether cappuccino rinsing should be prompted immediately or 10 minutes after a milk product has been prepared.
Example: Proceed as follows to programme that Cappuccino rinsing
should be prompted immediately after a milk product has been
prepared.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until RINSES is displayed.
k T Press the Rotary Switch to enter the programme item.
INIT RINSE MANUAL
g T Turn the Rotary Switch until CAPP RINSE AFTER 10’
is displayed.
k T Press the Rotary Switch to enter the programme item.
CAPP RINSE AFTER 10’
g T Turn the Rotary Switch until CAPP RINSE NOW is
displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
CAPP RINSE NOW
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
RINSES
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Unit amount of water /
time format
You can change the unit of the amount of water from ‘ml’ to ‘oz’ and
the time format to ‘24 HRS’ or ‘AM/PM’ .
Example: To change the unit for the amount of water from ML to
OZ, proceed as follows.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
44
5 Permanent settings in programming mode
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until SETTINGS 24HRS / ML
is displayed.
k T Press the Rotary Switch to enter the programme item.
SETTINGS 24HRS
g T Turn the Rotary Switch until SETTINGS ML is displayed.
k T Press the Rotary Switch to enter the programme item.
SETTINGS ML
g T Turn the Rotary Switch until SETTINGS OZ is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
SETTINGS OZ
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
SETTINGS 24HRS / OZ
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Language
You set the language when you used the machine for the first time.
Example: To change the language from ENGLISH to DEUTSCH
(example), proceed as follows.
Precondition: COFFEE READY is displayed.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until LANGUAGE ENGLISH is
displayed.
k T Press the Rotary Switch to enter the programme item.
LANGUAGE ENGLISH
g T Turn the Rotary Switch until SPRACHE DEUTSCH
(example) is displayed.
k T Press the Rotary Switch to confirm the setting.
GESPEICHERT w appears briefly on the display.
SPRACHE DEUTSCH (example)
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
BITTE WÄHLEN (example)
45
6 Maintenance
6 Maintenance
Your IMPRESSA has the following integrated maintenance programmes:
Z Clean cappuccino frother
Z Rinse machine
Z Rinse cappuccino frother
Z Clean machine
Z Decalcify machine
Z Change filter
E Clean or descale the machine or change the filter whenever
the appropriate prompt is displayed.
Maintenance tips
To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the
machine requires daily maintenance.
You should proceed as follows:
Z Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
Z Rinse the water tank with clean water.
Z Dismantle and rinse the frother (see Chapter 6 ‘Maintenance – Rinsing the cappuccino frother’).
Z Wipe the surface of the machine with a damp cloth.
Rinsing the machine
When the IMPRESSA is switched on, a prompt to perform a rinse
operation appears after heating, or this is automatically started.
It can be set in programming mode whether the switch-on rinse
needs to be activated manually or whether the machine automatically activates the switch-on rinse (see Chapter 5 ‘Permanent settings in programming mode – Rinses’).
When the IMPRESSA is switched off, a rinse operation is automatically initiated.
You can initiate the rinse operation manually at any time.
46
6 Maintenance
Precondition: COFFEE READY is displayed.
T Place a receptacle under the coffee spout.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
f T Turn the Rotary Switch until RINSE MACHINE is displayed.
k T Press the Rotary Switch to initiate the rinse operation.
MACHINE RINSING
Rinsing stops automatically and your IMPRESSA is then once
more ready for use.
Changing the filter
E After 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to replace the filter.
E After two months, the filter will cease to work. Monitor the
elapsed time by adjusting the date plate on the cartridge
holder.
E If the CLARIS filter cartridge is not activated, you will not be
prompted to change the filter.
@ You can also try out ‘Changing the filter’ online. Visit the
Knowledge Builder at www.jura.com.
Change following a prompt
To change the CLARIS filter cartridge when prompted to do so by
your IMPRESSA, proceed as follows:
Precondition: COFFEE READY / CHANGE FILTER is displayed, and the maintenance button c lights up.
c T Press the maintenance button.
DURATION 2 MIN. / START YES
E If you want to change the filter at a later point in time, turn the
Rotary Switch until START NO is displayed. Exit the maintenance programme by pressing the Rotary Switch. The prompt
‘Change filter’ remains on the display.
47
6 Maintenance
c T Press the maintenance button.
CHANGE FILTER / PRESS RINSE
T Remove the water tank and empty it.
T Lift the cartridge holder.
T Take out the old CLARIS filter cartridge and the extension.
T Fit the extension on top of a new filter cartridge.
T Insert the filter cartridge into the water tank, exerting slight
pressure.
T Close the cartridge holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert.
T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water flows out of the frother.
E You can interrupt filter rinsing at any time. To do this, press
any button.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml. The
IMPRESSA heats up and is once again ready to use.
Manual filter change
You can initiate the ‘Changing the filter’ operation manually.
Precondition: The filter is activated and COFFEE READY is
shown on the display.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until CHANGE FILTER is displayed.
48
6 Maintenance
k T Press the Rotary Switch.
DURATION 2 MIN. / START YES
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Replacement following a
prompt’.
Cleaning the machine
CAUTION
After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Use only original JURA care products.
E The cleaning programme only lasts about 20 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from stockists.
@ You can also try out the ‘Cleaning the machine’ operation
online. Visit the Knowledge Builder at www.jura.com.
Cleaning following a
prompt
Precondition: COFFEE READY / CLEAN MACHINE is displayed, and the maintenance button c lights up.
c T Press the maintenance button.
DURATION 20 MIN. / START YES
E If you want to clean the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance programme by pressing the Rotary Switch. The
prompt ‘Clean machine’ remains on the display.
c T Press the maintenance button.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the maintenance button c lights up.
49
6 Maintenance
T Place a receptacle under the coffee spout and the frother.
c T Press the maintenance button.
CLEANS, the cleaning operation starts.
The process is interrupted. ADD TABLET / PRESS
RINSE, the maintenance button c lights up.
T Open the cover of the filler funnel for pre-ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
c T Press the maintenance button.
CLEANS, water flows out of the coffee spout and the
frother several times.
E You can follow the current status of cleaning on the progress
bar.
The process is interrupted, EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
The cleaning operation is now complete. The IMPRESSA is
ready for use again.
Manual cleaning
You can initiate the ‘Cleaning the machine’ operation manually.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the rotary switch until CLEAN MACHINE is displayed.
k T Press the Rotary Switch.
DURATION 20 MIN. / START YES
T Continue with the second prompt to take action (indicated
by a T), as is described under ’Cleaning following a prompt’.
50
6 Maintenance
Descaling the machine
CAUTION
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse the descaling agent off with clean water. Should you get
any descaling agent in your eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.
T Use only original JURA care products.
CAUTION
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
CAUTION
If the descaling agent comes into contact with sensitive surfaces,
damage cannot be ruled out.
T Clean up any splashes immediately.
E The descaling programme lasts approx. 45 minutes.
E JURA descaling tablets are available from stockists.
E If you use a CLARIS filter cartridge and this is activated, you
will not be prompted to change the filter.
E Remove the CLARIS filter cartridge, if installed, before de-scaling the machine.
@ You can also try out the ‘Descaling the machine’ operation
online. Visit the Knowledge Builder at www.jura.com.
Descaling following a
prompt
Precondition: COFFEE READY / DECALCIFY MACHINE is
displayed and the maintenance button c lights up.
c T Press the maintenance button.
DURATION 45 MIN. / START YES
51
6 Maintenance
E If you want to descale the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance programme by pressing the Rotary Switch. The
prompt ‘Decalcify machine’ remains on the display.
c T Press the maintenance button.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
SOLVENT IN TANK
T Remove the water tank and empty it.
T Completely dissolve the contents of one blister (3 JURA descaling tablets) in a container that holds 600 ml of water. This
may take several minutes.
T Pour the solution into the empty water tank and insert it in
the machine.
SOLVENT IN TANK / PRESS RINSE, the maintenance button c lights up.
T Remove the frother from the Connector System©.
T Place a receptacle under the hot water spout and another
under the Connector System©.
c T Press the maintenance button.
DECALCS, water flows out of the Connector System© and
the hot water spout. The maintenance button c flashes
during the descaling operation.
E You can follow the current status of descaling on the progress
bar.
The process is interrupted, EMPTY TRAY.
T Empty the receptacles below the hot water spout and the
Connector System©.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
RINSE WATER TANK / FILL WATER TANK
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert.
PRESS RINSE, the maintenance button c lights up.
T Refit the frother.
52
6 Maintenance
T Place a receptacle under the coffee and hot water spout and
another under the frother.
c T Press the maintenance button.
DECALCS, water flows out of the frother and the hot water
spout.
The process is interrupted, HEATING UP.
MACHINE RINSING, water flows out of the coffee
spout. The operation stops automatically, EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
The descaling operation is now complete. Your IMPRESSA
heats up and is once again ready to use.
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Manual descaling
You can initiate the ‘Descaling the machine’ operation manually.
Precondition: COFFEE READY is shown on the display and the
filter is not activated.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until DECALCIFY MACHINE
is displayed.
k T Press the Rotary Switch.
DURATION 45 MIN. / START YES
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Descaling following a prompt’.
Rinsing the cappuccino
frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
Each time milk has been prepared the IMPRESSA displays a prompt
for Cappuccino rinsing.
It can be set in programming mode whether the rinsing prompt is
displayed immediately or 10 minutes after preparation (refer to
Chapter 5 ‘Permanent settings in programming mode – Rinses’).
53
6 Maintenance
Rinsing following a prompt
Precondition: COFFEE READY / RINSE CAPPUCCINO is
displayed and the maintenance button c lights up.
T Place a receptacle under the frother.
E If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
c T Press the maintenance button.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
appears on the display.
Starting rinsing manually
You can initiate the ‘Rinsing the cappuccino frother’ operation
manually.
Precondition: COFFEE READY is displayed.
T Place a receptacle under the frother.
E If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until RINSE CAPPUCCINO is
displayed.
k T Press the Rotary Switch to start the rinse operation.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
appears on the display.
Cleaning the cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
To ensure that the respective frother works perfectly, you should
clean it daily when you have been preparing milk.
CAUTION
54
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Use only original JURA care products.
6 Maintenance
E The JURA milk system cleaner is available from stockists.
@ You can also try out the ‘Cleaning the cappuccino frother’
operation online. Visit the Knowledge Builder at
www.jura.com.
Cleaning the cappuccino
frother – manually
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
k T Press the Rotary Switch.
CLEANER FOR CAPPU., the maintenance button c
lights up.
T Pour 250 ml of fresh water into a container and add one
capful (max. 15 ml) of milk system cleaner.
T Immerse the milk pipe in the receptacle with the cleaning
solution.
E If you are using the Professional Cappuccino Frother, turn
the selection lever to the milk foam p or milk t position.
T Place another receptacle under the frother.
c T Press the maintenance button.
CAPPUCCINO / CLEANS, the frother and pipe are
cleaned.
WATER FOR CAPPUCCINO, the maintenance button c
lights up.
T Rinse the receptacle thoroughly, fill it with approx. 250 ml
of fresh water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the frother
once more.
c T Press the maintenance button.
CAPPUCCINO / CLEANS, the frother and pipe are rinsed
with fresh water.
COFFEE READY appears on the display. Your IMPRESSA
is once more ready to use.
55
6 Maintenance
Cleaning the cappuccino
frother after a prompt
If milk has been prepared, but the cappuccino frother has not been
cleaned, the CLEAN CAPPUCCINO prompt is displayed when
the machine is switched off. The maintenance programme can be
started by pressing the maintenance button c.
Precondition: CLEANER FOR CAPPU. is displayed and the
maintenance button c lights up.
T Continue with the fifth prompt to take action (indicated
by a T), as is described under ‘Cleaning the cappuccino
frother – manually’.
Disassembling and
rinsing the Professional Cappuccino
Frother
T Carefully remove the frother from the Connector System©
by twisting slightly.
T Dismantle the frother completely.
T Rinse all the frother parts thoroughly under running water.
T Reassemble the frother.
E Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
T Firmly attach the frother to the Connector System©.
Disassembling and
rinsing the Easy Cappuccino Frother
T Carefully remove the frother from the Connector System©
by twisting slightly.
T Dismantle the frother completely.
T Rinse all the frother parts thoroughly under running water.
T Reassemble the frother.
E Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
T Firmly attach the frother to the Connector System©.
56
6 Maintenance
Cleaning the bean
container
WARNING
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These residues may negatively affect
the coffee results. For this reason clean the bean container from
time to time.
Danger of injury to the fingers when the grinder is running.
T Switch the machine off with the on/off button Q before performing any work on the grinder.
T Switch the machine off at the power switch 3.
T Open the cover of the bean container and remove the aroma
preservation cover.
T Remove the beans with a vacuum cleaner.
T Loosen the screw in the bean container and lift up the finger
protection.
T Remove the remaining beans with a vacuum cleaner.
T Clean the bean container with a soft, dry cloth.
T Put the finger protection down again and screw it back
tightly in place.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
Descaling the water
tank
Limescale deposits may form in the water tank. To ensure correct
function of your IMPRESSA, you should descale the water tank from
time to time.
T Remove the water tank.
T If you use a CLARIS filter cartridge, remove this.
T Descale the tank with a mild conventional descaling agent
in accordance with the manufacturer’s instructions.
T Rinse the water tank with clean water afterwards.
T If you use a CLARIS filter cartridge, insert this again.
T Fill the water tank with fresh, cold water and reinsert.
57
7 Display messages
7 Display messages
Message
Cause/Result
Action
FILL WATER TANK
The water tank is empty. You
cannot prepare any coffee
products, hot water or milk
products.
T Fill the water tank
(see Chapter 2, ‘Preparing and
using for the first time – Filling
the water tank’).
EMPTY GROUNDS
The coffee grounds container
is full. You cannot prepare any
coffee products, but you can
prepare hot water or milk.
T Empty the coffee grounds
container and the drip tray.
EMPTY TRAY
The drip tray is full. You cannot T Empty the drip tray.
prepare any coffee products,
hot water or milk products.
TRAY MISSING
The drip tray is not inserted
correctly or is not inserted at
all. You cannot prepare any
coffee products, hot water or
milk products.
T Insert the drip tray.
T Clean the metal contacts on
the back of the drip tray.
FILL BEANS
The bean container is empty.
You cannot prepare any coffee
products, but you can prepare
hot water or milk.
T Fill the bean container
(see Chapter 2, ‘Preparing and
using for the first time – Filling
the bean container’).
PRESS RINSE
The IMPRESSA is prompting
you to start a rinse operation
or continue a started maintenance programme.
T Press the maintenance button
to start rinsing or to continue the
maintenance programme.
COFFEE READY /
RINSE CAPPUCCINO
The IMPRESSA is prompting
you to start cappuccino
rinsing.
T Press the maintenance button
to start cappuccino rinsing.
COFFEE READY /
CLEAN MACHINE
After 220 preparations or
80 switch-on rinses, the
IMPRESSA will prompt you to
clean it.
T Clean the machine (see
Chapter 6, ‘Maintenance –
Cleaning the machine’).
58
7 Display messages
Message
Cause/Result
Action
COFFEE READY /
CLEAN NOW
Message, if in spite of prompt
no cleaning has been carried
out yet.
T Clean the machine (see
Chapter 6, ‘Maintenance –
Cleaning the machine’).
COFFEE READY /
The IMPRESSA is prompting
DECALCIFY MACHINE you to descale it.
T Descale the machine (see
Chapter 6, ‘Maintenance –
Descaling the machine’).
COFFEE READY /
DECALCIFY NOW
Message, if in spite of prompt
no decalcification has been
carried out yet.
T Descale the machine (see
Chapter 6, ‘Maintenance –
Descaling the machine’).
COFFEE READY /
CHANGE FILTER
After 50 litres of water have
flowed through, or after two
months, the filter will cease to
work.
T Replace the CLARIS filter
cartridge (see Chapter 6
‘Maintenance – Changing the
filter’).
COFFEE READY /
CHANGE NOW
Message, if in spite of prompt
no filter change has been
carried out yet.
T Replace the CLARIS filter
cartridge (see Chapter 6
‘Maintenance – Changing the
filter’).
NOT ENOUGH
PRE-GROUND
T The next time you make coffee
There is too little pre-ground
use more pre-ground coffee
coffee in the filler funnel. The
IMPRESSA stops the operation. (refer to Chapter 4, ‘Preparation
at the touch of a button –
Pre-ground coffee’).
59
8 Troubleshooting
8 Troubleshooting
Problem
Cause/Result
Action
Grinder is making a very
loud noise.
There are foreign objects
in the grinder.
T Contact customer support in your
country (see Chapter ‘JURA contact
details / Legal information’).
The frother does not
produce enough milk foam
or milk sprays from the
cappuccino frother.
The cappuccino frother
is dirty or incorrectly
attached.
T Rinse and clean the cappuccino
frother (see Chapter 6, ‘Maintenance –
Cappuccino frother‘).
T Assemble the cappuccino frother
correctly and firmly attach the frother
to the Connector System© (refer to
Chapter 6 ‘Maintenance – Disassembling and rinsing the frother’).
Coffee only comes out in
drips when it is being
prepared.
Coffee or pre-ground
coffee has been ground
too finely and is blocking
the system.
T Put the grinder on a coarser setting
or use coarser pre-ground coffee (refer
to Chapter 2, ‘Preparing and using for
the first time – Adjusting grinder’).
Water hardness cannot be
adjusted.
The CLARIS filter
cartridge is activated.
T Deactivate the CLARIS filter cartridge
in programming mode.
COFFEE READY /
FILL BEANS is
The grinder is not yet
completely filled with
beans.
T Prepare a coffee speciality.
The bean monitor is
dirty.
T Clean the bean container
(see Chapter 6, ‘Maintenance –
Cleaning the bean container’).
displayed although the
bean container has been
filled.
COFFEE READY /
FILL BEANS is not
displayed although the
bean container is empty.
EMPTY TRAY
is always displayed.
FILL WATER TANK is
displayed although the
water tank is full.
60
The metal contacts of the T Clean and dry the metal contacts
drip tray are dirty or wet. on the back of the drip tray.
The water tank float is
trapped.
T Descale the water tank (see
Chapter 6, ‘Maintenance – Descaling
the water tank’).
8 Troubleshooting
Problem
Cause/Result
Action
ERROR 2 is displayed.
If the machine was
exposed to the cold for a
long period of time, it is
disabled from heating up
due to safety reasons.
T Warm up the machine at room
temperature.
Other ERROR messages
are displayed.
–
T Turn the IMPRESSA off at the power
switch. Contact customer support in
your country (see Chapter ‘JURA
contact details / Legal information’).
E If you have not been able to solve the problem, contact
customer support in your country (see Chapter ‘JURA contact
details / Legal information’).
61
9 Transport and environmentally neutral disposal
9 Transport and environmentally neutral disposal
Transport / Emptying
the system
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transportation.
In order to protect the IMPRESSA from frost during transportation,
the system must be emptied.
Precondition: The IMPRESSA is switched off (standby).
T Remove the water tank.
T Place a receptacle under the hot water spout and another
under the frother.
c T Press the maintenance button until SYSTEM
EMPTYING appears.
A small amount of water flows from the frother and the
hot water spout. The operation stops automatically. The
IMPRESSA will switch itself off.
3 T Turn your IMPRESSA off at the power switch.
E The next time you use the machine the system must be
refilled (see Chapter 2, ‘Preparing and using for the first
time – First-time use’).
Disposal
Please dispose of old machines in an environmentally neutral way.
H
62
Old machines contain valuable materials capable of being recycled
which should be salvaged for recycling. Please therefore dispose of
old machines via your regional collection system.
10 Technical data
10 Technical data
Voltage
Power
AS
220–240 V AC, 50 Hz
F
120 V AC, 60 Hz
D
220–240 V AC, 50 Hz
G
220 V AC, 50 Hz
1450 W
F 1250 W
Safety test
SDFG
Airborne noise emitted
Lp < 70 dB (A)
Energy SAVE NO
40 Wh
Energy SAVE LEVEL 1
20 Wh
Energy SAVE LEVEL 2
15 Wh
Pump pressure
Static max. 15 bar
Holding capacity of water tank
5.7 l
Holding capacity of bean
container
280 g (optional 750 g)
Holding capacity of coffee
grounds container
Approx. 40 servings
Cable length
Approx. 1.1 m
Weight
13.8 kg
Dimensions (W x H x D)
41 x 47 x 39 cm
63
Index
Index
A
B
C
D
Aroma preservation cover 8
Automatic switch-off 43
E
Bean container
Aroma preservation cover 8
Cleaning 57
Cover 8
Filling 17
Cappuccino 31
With the Easy Cappuccino Frother 32
With the Professional Cappuccino
Frother 31
Cappuccino frother
Cleaning 54
Easy Cappuccino Frother 16
Professional Cappuccino Frother 16
Rinsing 53
CLARIS filter cartridge
Changing 47
Using and activating 19
Cleaning
Bean container 57
Cappuccino frother 54
Machine 49
Coffee 30
Coffee à la carte 31
Coffee grounds container 8
Coffee spout, height-adjustable 8
Connector System© 8, 16
Control options 24
Cover
Bean container 8
Filler funnel for pre-ground coffee 8
F
Default settings in programming mode 38
Descaling
Machine 51
Water tank 57
Display messages 58
Drip tray 8
L
64
H
I
K
Easy Cappuccino Frother
Disassembling and rinsing 56
Emptying the system 62
Energy-saving mode 40
Entering a default setting for the amount of
water for a cup size 26
Errors
Troubleshooting 60
Espresso 30
Filler funnel for pre-ground coffee 8
Filling
Bean container 17
Water tank 17
Filter
Changing 47
Using and activating 19
Fineness of grind
Adjusting grinder 22
Fineness of grind switch 8
Fineness of grind switch 8
First-time use 18
Frother
Easy Cappuccino Frother 16
Professional Cappuccino Frother 16
Hardness of water 21
Hot milk 35
Hot water 37
Hot water portion 37
Hot water spout 8
Internet 16
Knowledge Builder 16
Language 45
Latte macchiato 33
With the Easy Cappuccino Frother 34
With the Professional Cappuccino
Frother 33
Index
M
O
P
Machine
Cleaning 49
Descaling 51
Rinsing 46
Setting up 17
Switching off (stand-by) 23
Switching on 22
Maintenance 46
Maintenance tips 46
Milk
Foaming and heating with the Professional Cappuccino Frother 35
Foaming with the Easy Cappuccino
Frother 36
Hot 35
Milk portion 35
Milk foam 35
R
S
One-off settings before and during preparation 25
Power switch 8
Pre-ground coffee 34
Filler funnel 8
Pre-ground coffee 34
Preparation
At the touch of a button 30
Cappuccino 31
Coffee 30
Coffee à la carte 31
Espresso 30
Hot water 37
Latte macchiato 33
Milk 35
Pre-ground coffee 34
Problems
Troubleshooting 60
Professional Cappuccino Frother 8, 16
Disassembling and rinsing 56
Programmable switch-on and switch-off
time 42
T
U
Programming mode 38
Automatic switch-off 43
Energy-saving mode 40
Language 45
Products 38
Rinses 44
Switch-on and switch-off time 42
Time and weekday 41
Unit amount of water / Time format 44
Prompt to take action
Symbols used 14
Rinses 44
Rinsing
Cappuccino frother 53
Machine 46
Rotary switch 9
Safety 10
Selector switch 9
Settings
Default settings in programming
mode 38
Entering a default setting for the amount
of water for a cup size 26
One-off settings before and during preparation 25
Setting up 17
Standby
Switching off 23
Switching off (stand-by) 23
Switching on 22
Technical data 63
Time and weekday 41
Troubleshooting 60
Use
Proper 10
Use, First time 18
65
Index
V
Viewing information and maintenance
status 29
Viewing maintenance status 29
W
Water hardness 21
Determining and adjusting 21
Water tank 8
Descaling 57
Filling 17
Works settings 40
66
67
J67415/XS95/en/201510
JURA contact details / Legal information
Your JURA dealer:
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel. +41 62 38 98 233
www.jura.com
Directives
The machine complies with the following directives:
Z 2006/42/EC – Machinery Directive
Z 2004/108/EC – Electromagnetic Compatibility
Z 2011/65/EU – RoHS Directive
Technical changes
We reserve the right to make technical changes. The illustrations
used in the IMPRESSA XS95/XS90 One Touch Manual show the
IMPRESSA XS95 One Touch model. Your IMPRESSA could incorporate minor changes.
Feedback
Your opinion is important to us! Use the contact details at
www.jura.com.
Copyright
The Instructions for Use contain information which is protected by
copyright. It is not permitted to photocopy or translate these
Instructions for Use into another language without the express
written consent of JURA Elektroapparate AG.
68
Download PDF