Compact C 2010 models Instruction Book
Page
1
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
There are three versions of THE iCOOL COMPACTS
C
C
OMPACT Cool is our most popular and economic system. It provides
rapid cooling, fully automatic control and excellent mobility.
OMPACT Dual Temp provides all the power and function of the “Cool”
plus both cooling and heating automatically, for advanced contrast
therapy sessions.
C
OMPACT Twin is the most powerful mobile ice bath cooling system
available. It has all the features of the “Cool” plus extra cooling power
and stronger water flow for cooling 2 pools at once if required or for cooling
spa baths and larger iCool Demountable multi person pools.
THE OPERATION OF ALL 3 MODELS IS THE SAME EXCEPT WHERE NOTED
IN THIS MANUAL
MODEL
COOLING POWER
HEATING POWER
COMPACT Cool
3000 Watts
-
COMPACT Twin
5100 watts
COMPACT Dual Temp
3200 Watts
2400 Watts
-
VOLTAGES
AVAILABLE
220-240 0R 110
220-240 OR 110
220-240 OR 110
IMPORTANT SAFETY ADVICE
POWER SUPPLY VOLTAGE
iCools can only be used with the voltage marked on the machine, they are not multi voltage. The voltage is
marked next to the main power socket.
TO ENSURE SAFE OPERATION THE POWER OUTLET YOU USE MUST HAVE A PROPER EARTH CONNECTION.
BUILT IN SAFETY SYSTEMS
Your iCool system has many safety features to protect against such things as a loss of water flow, overheating
of the system, or any chance of the user receiving an electrical shock. If any such potentially dangerous things
should occur, in most cases your iCool will shut itself down and a red warning screen will appear to assist you
to identify and correct the problem. In the case of overheating, the main fan will continue to run for some time
until the temperature is safely back to normal.
For the safety of users, any leakage of even a small amount of electrical current will cause the system to
Instantly remove all electrical power.
In the unlikely event that your system shuts itself down for any of these reasons, you must identify and correct
the problem that has caused the safety systems to operate before allowing anyone to use the system.
PLEASE TEST THE EARTH LEAKAGE SAFETY DEVICE REGULARLY
The main power switch is also part of the electrical safety circuit that can prevents the possibility of electric
shock. It is essential to test this safety system each time you use the iCool to make
certain it is operating correctly. This is very easy to do and takes only a few seconds.
Turn on the main switch and then press the orange test button just above the switch.
If the safety system is working normally, pressing the test button will cause the main
power switch to shut off instantly.
After a successful test, reset the main switch to ON to begin normal operation. If
pressing the test button fails to instantly shut off the power switch DO NOT USE THE
SYSTEM until you contact iCool for advice. Failures of this system are very rare.
Page
2
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
ADVICE ABOUT OBTAINING THE CORRECT FLOW OF WATER
Water flow through your iCool is produced by a high-quality long life circulating type pump that for safety is
completely isolated electrically from the water.
Circulating type pumps can lift and move water reliably for many thousands of hours, however they do not provide suction and are therefore not self priming. Self priming type pumps are generally not as reliable over long
periods and so are not suitable for this type of system.
This means that the pump in your iCool can not begin to operate unless it is fed with a head of water above the
pump and any air tapped in the system is removed. The water in the pool must be above the water inlet connector on your iCool cooling system before you start to pump. Furthermore, there must be no air trapped in the
supply hose and no part of the hose from the pool to the cooling system can be above the level of the water as
this traps air which can prevent water from flowing.
Water pumps can not operate for long periods without water as the water provides the lubrication. To prevent
damage, your iCool system will shut down the pump if water is not flowing properly for more than three minutes. If this happens a warning screen will normally appear to explain to you how to correct the problem.
To assist in removing trapped air quickly our iCool is fitted with an automatic air bleed system plus a manual
air bleed valve on the rear of the unit at the bottom. Once you have connected the
hoses as described in this manual and started the pump, if water does not flow at
normal force after 2 minutes, open the air bleed valve and allow water to escape.
This valve is directly connected to the pump body and any trappeed air will be
removed. It could take up to 2 minutes, although normally a few seconds is enough.
Once water is flowing back to the pool normally, close the air bleed valve. Normal
flow will fill a standard bucket in about 1 minute.
If you are using the system in an area where you can not let water run on the floor,
please attach the small 12 mm diameter hose provided and run the bleed water into
a bucket.
IT WILL NOT ALWAYS BE NECESSARY TO BLEED THE SYSTEM AND IF YOU NEED TO DO SO IT WILL ONLY
BE NECESSARY ONCE FOR EACH SET UP. Once primed of air, the system will remain primed until it is emptied
or moved and water will normally flow instantly each time you start the pump.
NEVER USE CORROSIVE CHEMICALS
These chemicals can cause major damage even to the high grade stainless steel heat exchanger in your iCool
and cause a total system failure that can not be covered by your warranty. These chemicals eat away most metals and are are also damaging to athletes. For total control of bacterie use an innexpensive iCool Ultra Violet
Steraliser unit. This is the totally safe way to deal with bacteria and keep your pool safe without using expensive and potentially damaging chemicals. Avoid prolonged use of salt water to ensure long life of your system.
Quick start guide
The following is a quick start guide to get your iCool up and running quickly, however it is strongly advised that
you read the rest of the manual as it contains a lot of information that you really need to know to get the most out
of your system.
STEP 1
Before you turn on your iCool system you must set up and fill the pool. iCool portable inflatable pools and semi
permanent demountable pools come with their own instructions and are easy to set up. Just be sure that they
are in the position you require before you fill them with water as the weight of the water will make it impossible to
move them once they are filled.
Page
3
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
Before you fill the pool you must connect the 2 hoses provided. The connections are clearly marked on both the
pool and the iCool system. ICool hoses have convenient snap fittings that are very quick and easy to use. Make
sure that the small clear plastic in line filter in the hose carrying water from the pool to the iCool is in place and
is clean, as this prevents contamination such as hair or fabric particles from clogging the heat exchange mechanism. The end of the hose that contains the filter is connected to the cooling system not the pool. Also the white
perforated inner filter membrane inside the clear filter housing must be installed in the correct direction or it will
block the flow of water. It is correctly installed when it is held in place by the screw fitting , it should not float
about inside the clear filter housing.
STEP 2
Fill the pool with clean fresh water (not saltwater) to the level marked on the pool liner. Never use chlorine or bromide solutions as these chemicals can attack the stainless steel heat exchange panels that remove heat from the
water. Because the water is very cold, bacteria is not normally a problem for one or two days use. If you intend to
use the pool for longer periods without changing the water then you should use an inexpensive iCool compact
ultraviolet sterilising unit or for permanent use a full iCool self powered filtration and sterilising unit.
Your iCool is fitted with both an automatic and a manual air romoval bleed valve (see a full description on page
2) that will normally bring the water flow to full force in 1 to 2 minutes providing you meet the conditions set out
below. Normal water flow from your iCool will fill a standard water bucket in about 1 minute.
The water level in the pool must be above the water
inlet and outlet connections on the iCool.
The iCool must be on the same level surface as the
pool. It must not be above the pool.
WATER FLOW WARNING
If water does not flow correctly after 3 minutes either during the
initial set up or at any time during normal operation an alarm will
sound, THE SYSTEM WILL STOP TO PROTECT THE PUMP and a
red warning screen will appear with instructions.
You must find the reason for the lack of water flow or the system
will stop every 3 minutes for safety until the water flow is correct.
IF THE WATER FLOW WARNING APPEARS
Please check to see that the hoses are not bent or blocked under heavy objects and that the lower
hose is not higher than the water in the pool at any point as this will trap air.
The red screen that will appear gives you 2 options. (see the illustration on the next page) Normally
you would touch the RESTART PUMP button and then bleed the system again by referring to the instructions above and the advice about water flow on page 2.
In most cases this will fix the problem an return the system to normal operation. If all the trapped air is
not removed by the automatic system or the manual bleed valve you can also remove the top hose fitting from the cooling system for a few seconds while the pump is running untill the air escapses. This
is not normally necessary but can help in diffcult situations.
Page
4
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
The Water Flow Warning Screen also
provides an option to over ride the flow
protection system in the rare situation
of a false alarm.
NEVER USE THIS OPTION UNLESS YOU
ARE ABSOLUTELY CERTAIN THAT THE
SYSTEM IS STOPPING BECAUSE OF A
FALSE WATER FLOW ALARM!
Once you use this function to disarm
the flow safety monitor nothing will
stop the system even if water is not
flowing and this can seriously damage
the pump as it will have no lubrication
or cooling from the water.
This over ride function is only to be used for short
periods where it is essential to keep your system operating until the reason for the false
alarm can be determined and corrected.
WATER FLOW CAN ALSO STOP IF THE HEAT EXCHANGER TANK IS FROZEN SOLID!
If you set the temperature below about 7ºC or 45ºF it is occasionally possible in certain climatic conditions for the heat exchange tank to freeze solid which will block most , but not all, of the flow of water.
A small amount of water may still be flowing through the automatic air bleed system which bypasses
the heat exchanger, but the safety system monitors the heat exchanger tank flow only and if no water
is flowing through the tank the system will stop.
In order to cool the pool water to these extremely low temperatures the system must cool to at least
5 to 7ºC below the set temperature and this takes it very close to the temperature that water freezes
solid.
Following international safety standards your iCool will not accept water temperature settings below
6ºC or 42ºF as this would put athletes using the system unattended at risk of hypothermia. However,
the iCool is easily powerful enough to freeze the water inside the system itself and if this happens the
safety screen above will appear and the system will stop.
Please be aware that the tank can only freeze if your setting is below 7 to 8ºC and this can only happen in certain conditions. If your set temperature is above this then it is much more likely that the
system has stopped because of a lack of water flow caused by either a hose or filter obstruction, or
an air leak in the hoses, or trapped air in the system.
If there is a possibilty that the heat exchanger tank is frozen, then you must allow the system to warm
up for about 30 minutes to thaw the ice. Leave the power switched on so that the fan can operate if
necessary to thaw out the tank. Set a new temperature no lower than 8 or 9ºC before restarting so that
the tank does not freeze again.
STEP 3
Connect the power cable provided with your iCool to a standard power outlet capable of providing at least 12
amps in countries with a 220 V supply and 24 amps in countries with a 110 V supply. Although the system
requires much less power than this in normal operation, all heat pump compressor motors need considerably
more power for a minute or so each time they starts up.
FOR SAFETY, THE POWER OUTLET YOU USE MUST BE EARTHED CORRECTLY.
The main power switch is also part of the electrical safety circuit that prevents the
possibility of electric shock. It is a good idea to test this system each time you use
the iCool by turning on the main switch and then pressing the test button above the
switch. If the safety system is working normally, pressing the test button will cause
the main power switch to shut down instantly.
After this test, reset the main switch to ON to begin normal operation.
Page
5
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
STEP 4
YOUR SYSTEM SOFWARE WILL BEGIN LOADING
Your iCool has a full colour high-resolution touchscreen that
eliminates all switches and provides complete control over your
iCool system in a user-friendly and intuitive manner. It also
provides a substantial amount of additional information to assist
you.
When you turn on the power for the first time the system will load
the latest software from its memory card and run a diagnostic self
test routine. This will take about 20 seconds. During this time you
will see this screen and then a black screen.
the software loading screen
THE STATUS BAR WILL FLASH WHITE
The STATUS BAR on top of the iCool changes colour or flashes to give a
clear indication of each function.
While the software is loading the status bar will flash white while the screen
shown above and then a black screen appears for about 15 seconds while
the computers test the safety systems.
Then, the status bar will stop flashing and show a steady white light to
indicate that the systems check was successful and it is ready to use.
THE STATUS BAR LIGHT
IN MOST CASES A PERSONAL LOGO WELCOME SCREEN WILL APPEAR AT THIS TIME
ABOVE ARE EXAM[PLES OF TYPICAL CUSTOMER LOGO WELCOME SCREENS.
Touch the logo screen anywhere to continue.
This will lead to the “HOME” screen.
The HOME screen offers several choices to
Begin operation,
Set the system settings,
Set the time clock or
Get assistance from the built in HELP menus.
the HOME screen
Page
6
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
The home screen provides many options which are covered elsewhere in this manual, however to quickly start
the system you need only select either the use previous settings button or the make new settings button. The system remembers your last pool temperature settings, but if you have not used it before or if power
has been removed since your last session it will default to either
10ºC or 15°C/59°F. These are the most common temperatures used
for recovery sessions. The temperatures can be displayed in Centigrade or Fahrenheit. This is explained later in this Manual.
For your first quick start you should touch the make new
settings button. This will take you to the screen that allows you
to set the pool water temperature that you require. Simply touch
the up and down arrow buttons and the desired pool water temperature will appear on the bottom left-hand of the screen in the
blue window marked “selected temperature”. The righthand side of the screen shows the outside air temperature.
10
22
water temperature setting screen
Once the pool water temperature you want your iCool to cool to is showing, touch the start button. This
completes the setup and takes you to the main run screen which is the screen that you will use most of the time
during normal operation.
STEP 5
Touch the START PUMP button. This will start the pump operating
and water should begin circulating. NOTE! When you touch START
buttons they change to STOP buttons and can then be used to
STOP that function if required.
START
START
30
It is essential that the water is flowing correctly
before you TOUCH the SYSTEM start button.
The water flow is pre set to an optimum flow of about 20 litres or
around 5 gallons per minute. This allows time for the heat exchanger to operate at maximum cooling efficiency.
Pool water is completely changed approximately every 15 minutes.
MAIN OPERATION screen
Do not touch the system button until you are sure that water is flowing smoothly. If water does not flow smoothly
within a couple of minutes please check that the hose from the bottom of the pool is flat on the floor and no part
of it is higher than the top of the water. Check that the water in the pool is higher than the inlet connectors on the
iCool. If this does not correct the problem the system will sound an alarm and a red warning screen will appear
with information about how to correct the water flow problem.
24
30 22
STEP 6
Now that you have pre set your desired temperature and started the circulating pump, the touch screen should
look like the picture below. (of course the temperatures may be different). Notice that the pump button has
changed from start to stop. You can use this same button to start and stop the pump at any time.
Now, touch the start system button and the cooling cycle will begin. The water will be cooled to your preset
temperature and the system will cycle to maintain it at that temperature automatically. The SYSTEM can only be
started once within any 3 minute period to avoid overloading the compressor. If you don’t hear it start do not
touch the START SYSTEM again , it will start automatically after the 3 minutes safety period elapses.
If your iCool is the contrast MODEL then, depending on the temperature you set, it will either heat or cool the
water automatically to reach your preset temperature and then maintain it at that temperature. More detailed
information about the operation of the contrast version can be found later in this manual.
for THE safety of users, you can not set temperatures below 5°C or above 45°C. (40°F-112°F)
in an emergency you can stop all functions immediately by touching the “all stop” button
however, if the cabinet is hot, the fan may continue to run until the cabinet has cooled.
Page
7
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
START
START
STOP
START
24
10
30
22
MAIN OPERATION screen
details of the main operating screen
The pool temperature window shows the actual water temperature returning from the pool. This will vary
slightly to the actual temperature in the pool because for safety reasons the electronic sensor is in the cooling unit not in the pool. It accurately reads the actual temperature of the water that is returning to the pool. The
actual pool temperature will be slightly different depending on your particular setup. The temperature is always
accurately maintained but if you want to display the actual pool temperature within 1 degree you can simply set
an offset amount to compensate for the difference when selecting your reuired temperature.
The heat pump temperature window shows the temperature inside the cabinet. If this exceeds 70°C or
158°F the system will shut down, an alarm will sound and a warning screen will appear. This could happen in
extremely hot conditions or if the unit is covered by an object such as a towel or anything that prevents proper
airflow.
The outside temperature window shows the current room or outside temperature. It is not desirable to
operate this system in temperatures above 42°C or 108° F. If the reading exceeds this you need to move the system to a cooler area or improve the air flow. The preset temperature window always shows your selected
temperature. This is the temperature the water will be automatically cooled (or heated) to and maintained at.
Changing the temperature setting
You can change your preset temperature at any time by touching the change setting button, this will take
you to the change settings screen. From here you proceed as described previously. If you have the contrast
model, for safety reasons you cannot change directly from heating to cooling or cooling to heating. To do this
you must switch off the entire system at the main switch and start again. This is required to reset the computer.
FAN SPEEDS
During normal operation the main fan will automatically change speeds as required to maintain the highest
efficiency. The fan will be at full speed when temperatures are high or the water is warm.
Page
8
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
You can display the POOL temperature AT full-screen size
.
If you touch the number in the pool temperature window on the Main Operation Screen for a few seconds the
screen will change to a full-screen display of that temperature.
This is useful if you wish to monitor the system from a distance.
The pre-set temperature and the outside temperature continued
to display in smaller windows for your reference.
To return to the main operating screen touch the BACK 1 button.
14
To stop the system at the end of your recovery
session
10
25
There are several ways to stop the system and close it down.
You can stop the cooling system by touching the stop system
button, in this case the pump will continue to run, however you can stop to pump at any time by touching the
stop pump button. Alternatively you can stop everything by touching the all stop button. Alternatively
you can simply switch off the main power. If you use the all stop button the fan may continue to run for a
short time to cool the cabinet.
Emptying the pool USING THE BUILT IN PUMP.
You can use the main circulating pump to empty the water from the pool by detaching the top hose from the top
of the pool and directing it to a drain. The pump can be turned on and off at any time using the pumps stop/
start button.
System settings
detailed
operation
the touch button functions
When your iCool start up, the first screen you will see offers you a system settings
button. OPTIMUM SETTINGS ARE AUTOMATICALLY SELECTED so there usually no need to use
this feature. The three settings you can change are the fan speed range, the temperature from
degrees Centigrade to Fahrenheit and the sound level from the screen.
Main cooling fan speed. This allows you to set the main cooling fan to either NORMAL
or QUIET MODE. Generally you should always leave it in the NORMAL mode which is fully
automatic and allows the system to control the
fan speed to give the very best efficiency and fastest cooling.
If you are in a very quiet environment you can select QUIET
MODE, but you must be aware that this will reduce the cooling
ability of the system, however it will be quieter overall as the fan
will not run higher than 60% of maximum unless there is a risk
of overheating, in which case the safety system will turn the fan
back to high no matter what the setting. The NORMAL setting
is used to give absolute maximum cooling power where higher
fan noise is not a problem. On a normal day this gives about
25% more cooling than in the QUIET MODE.
If cooling seems lower than normal, check to see if this feature
was previously set to Quiet Mode.
Temperature display scale this can be set to either Centigrade or Fahrenheit and this changes all of the
displays throughout the entire system. When you first start the iCool it will normally start in Centigrade as this is
the world standard. Due to complex decimal calculations between Cº and Fº there may be minor difference in the
true Fº displays. This has no effect on actual cooling accuracy.
The sound level adjusts the sounds made by touching the screen and by the alarms. Normally it should be
left on high to assist with settings and to make sure alarms are heard.
A red dot indicates which setting is selected in each of the available settings.
Page
9
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
temperature settings
When your iCool starts up, you are offered 3
different ways to choose a water temperature
setting. Whichever method you choose it eventually
takes you to the main run screen. If you make no
setting, the system will automatically insert 15°C.
(around 59ºF) In this case you would navigate
directly to the main run screen in order to access
and start the pump and cooling system.
If you want to use your previous setting from the
last session, you can touch the use previous
setting button and the last setting you used will
be automatically inserted into the system. Previous
settings may have been lost if you have removed to
mains power.
If you want to make a new setting, which is the most common
choice users make, you touch the make new settings
button and this will take you to the screen illustrated above,
where you can use the up and down arrows to select the
temperature you require. After you make your setting touch of the
start button to go to the main screen where you can start both the
pump and the cooling system and where all relevant temperature
information is clearly displayed.
10
10
27
14
27
water temperature FULL screen
Temperature limitations
Because of the dangers of hypothermia in the case of an unattended athlete using the pool, your
system will not allow you to set temperatures below 5°C/40°F. If the model you are using is the
contrast model which also provides heating for contrast therapy you cannot set the temperature
above 45°C/112°F because of the risk of scalding. These temperature limits have been set after
wide consultation with the sporting industry around the world. There are no demonstrated benefits
in using water temperature lower than 5°C or above 45°C and therefore the risk of doing so is not
justified.
Timing functions
Your iCool offers a number of very useful timing
functions including a real-time clock, a countdown
timer to time recovery and training sessions and
a timer to shut down the system automatically at
a predetermined time after use. To set up and use
these functions touch the timer function button
on the home screen. You can reach this screen by
using the back 1 button or the home button.
In order to use these functions you first need to set the time of
day on the built-in clock.
11:25
time setting screen
To set the clock touch the set main clock button on the timing functions screen and the time setting display
on the bottom right of the screen will begin flashing. You must set it while one of the numbers is flashing by
using the up down and left right keys. Once you stop using these keys for more than a few seconds the display
will stop flashing and the time showing is set into the system and the clock begins operating.
The iCool clock operates in the universal 24-hour time style.
Page
10
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
Automatic system shutdown timer
You can preset your iCool to shut down at any time up to five hours in the future. This is very
convenient for coaches and specialists who may want to leave the training area early but want
to make sure that the system is not left running needlessly. To set this time, touch the set
shut down button and the clock digits on the bottom right of the screen will begin to flash
as with setting the clock. Use the same up down and left right arrows
to set the number of hours and minutes you wish to elapse before the
system automatically shuts down. The system automatically begins the
countdown and will stop when the time you set reaches zero. The time
remaining before shutdown is displayed on the main clock display screen.
As the same arrows are used to set all three time functions, to avoid confusion, a red
dot appears next to be button of the function being set.
A very popular and useful feature of your iCool is the session countdown timer.
This allows you to accurately control the immersion times of athletes and to repeat those times as often as needed. This is an essential part of successful cryo recovery therapy and is just as important as maintaining accurate
and consistent temperatures, which of course your iCool does perfectly.
The session timer is set up from the main time setting screen by touching the set countdown button.
The numbers on the setting screen in the bottom right-hand corner will begin to flash and you can use the left,
right and up, down arrows to change the time in minutes and seconds. Once you have set the time you want your
athletes to remain in the bath, touching the display countdown full-screen button will take you to the
screen illustrated below. This screen allows you to see the countdown from a distance and also to control it in
various convenient ways. The current pool temperature and the outside temperature will also be displayed.
The count down can be set for once only, or it can repeat automatically as many times
as you like. This is particularly convenient if you have a number of athletes using
the same pool at the same time. The system beeps for each of the last five seconds
the end of each countdown to warn the athletes to get ready to get either in or out of
the pool and pauses for several seconds to allow the changeover before the countdown begins again (if it is set in the repeat mode).
Resets time to the preset
value in the single shot mode,
ready to start again by pressing the start button
When this button is pressed
the countdown will repeat
until the repeat function is
cancelled by pressing once
again. A red dot indicates that
it is active
14
2:10
at
You can pause the countdown at any time and start
again from the same position
with this button, or touch
reset to start from the top.
27
This button starts the
countdown
Page
11
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
You can also display the main clock, showing
the time of day in full-screen mode if
required by touching THE display clock fULL
screen buttoN.
To go back to the previous screen touch the back 1
button.
14
14:10
2:41
External lighting
All iCool models have convenient area lighting
which is very helpful if the area around your pool
arrangement is not well lit. The lights can be
activated from a simple lighting control screen.
The lighting control screen can be accessed from
several screens by touching the lights button
This Takes you to a simple screen that has
both on and off light icon buttons. When you touch the on
button the area lights illuminate and a red dot beside the icon
indicates that the lights are set on.
Simply reverse the procedure to turn the lights off. If the lights
are activated they do not turn off when you touch the all stop
button or when the system initiates a safety shutdown. This
allows an extra measure of safety by continuing to light the area even if a fault has been detected.
stereo sound system
Some iCool models have a very high quality stereo
sound system built in to allow athletes to plug-in
their iPods or MP3 players or any other entertainment devices and listen to powerful, quality sound
while they use the iCool recovery system. This has
been a very popular feature and contributes to the
general feeling of well-being that everyone reports
after regular use of ice bath recovery systems. Of course this
feature has no effect if you’re particular ICool model does not
have a sound system built-in.
To activate the sound system touch the sound button, which is
available on several screens. This takes you to a simple sound
control screen that turns the amplifiers and speakers on and off.
Plug-in any music player to the mini phono jack provided. The volume is controlled by your music player not by
iCool stereo system, so be sure the volume is turned down when you first plug in your player.
The help system
Your iCool has an extensive built-in electronic help
system. Detailed and well illustrated helpful information on every important subject to do with the
operation of your iCool, is available from almost
any screen simply by touching the help button.
Touching any help button will take you to the screen illustrated
on the right. The screen has eight menu buttons covering all of
the important topics you are ever likely to need assistance with.
When you touch the menu button covering the topic you need
assistance with, the screen will change to a series of pages
covering that subject. Sample screens are illustrated below and
opposite.
Page
12
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
You can flip forward or backwards from page to page using the buttons on the right-hand side of the help
screens or you can return to be main help menu page at any time.
The built-in illustrated help system is a revolutionary new idea and we are constantly updating it as new
information and new feedback comes in from all over the world from iCool clients and from our recovery
research programs in several countries.
Some help pages may not be installed on your iCool when it is delivered, so that your local dealer can install them to suit your country and sport. Aternatively iCool can provide a free update memory card with
the latest help menus to suit your needs.
examples of the electronic help system’s pages
You may need a free local upgrade memory card to access all help files for your region.
Locking your iCool system to prevent tampering.
your iCool has an electronic lock
As you can see, iCool Systems have attractive user interfaces, this makes them
easy and very intuitive to use, but the downside is that untrained people sometimes like to play with the colourful touchscreens. As with any sophisticated
piece of equipment when people start pressing buttons at random anything can
happen. Your iCool has many safety features to prevent a person tampering with
the system from causing a disaster, but most of these safety features involve
Automatically shutting down the system which of course is undesirable.
We have covered this by installing a secret locking routine. It is a good idea to keep this secret to
as few people as possible.
To lock the screen so that no further inputs can be made, touch and hold the iCool icon on the
main run screen for more than 10 seconds (you can only lock from this main screen). A picture of
a lock will appear. While ever this lock is visible it is not possible to make any inputs or to change
screens.
To unlock the system and returned to normal, repeat the procedure. Touch and hold the iCool icon for more than
10 seconds. The lock will disappear and all functions will return to normal.
Page
13
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
emergency override provisions
certain safety features in your iCool can be overridden in the event of a partial failure
ICool systems are very reliable and have attained an excellent reputation around the world for this. In addition
we have done all that we can in the designs to build-in ways to work around any partial failure, so that you
are not prevented from using your system for an important event. There are some circumstances in which it
would be acceptable to temporarily override certain safety systems that may become too sensitive and cause
trouble until they can be properly readjusted. This allows systems to continue to operate in circumstances
where otherwise it might not be possible. Of course we do not allow the overriding of electrical safety circuits, this is not acceptable under any circumstances.
For example, depending on the way your system has been set up, it sometimes occurs that the water flow
monitoring system may be too sensitive and will stop the pump because it appears that water is not flowing properly. We allow this to be over ridden if it becomes troublesome. Instructions on how to do this will
appear on the screen automatically if this happens. It must be remembered of course that if you disarm this
system the pump is no longer protected from running dry and therefore without lubrication so it is essential
that you manually monitor the water flow. Our staff can assist you by phone or e-mail to overcome most
problems on the spot.
even iF the entire touchscreen user interface fails, we can USUALLY still get you
going.
In our efforts to remain the world’s number one supplier of mobile ice
bath systems, we have continued to improve reliability, but we have also engineered ways to ensure that no
matter what happens in the field, in most cases you can still use your iCool for that important event.
Realistically, even the best electronic systems occasionally have problems, especially in portable systems
that have a relatively hard life.
Fortunately, we have very few such problems, but as an added benefit we have built into all iCool’s a complete manual override system that allows your iCool to operate effectively even if all of the main electronics
fail for whatever reason.
We do not publish this over ride information in the manual because it is a little different from model to
model, but in the rare event that you ever have a failure of the electronics which prevents you from operating your iCool, just call or e-mail the local iCool representative in your country, or our international number
or go to our web site
www.iCoolsport.com where you will find a listing of representatives around the world, or you can request
a reply directly from our headquarters. You will be contacted promptly and we will explain how to work
around your problem until we can arrange repairs. This is an important service that we hope you never
need, but it’s good to know it is there.
In addition to this service you will be pleased to know that your iCool is of a modern modular design, which
means that most components can be easily replaced in the field and often by the owner.
Page
14
USER MANUAL FOR iCOOL RECOVERY SYSTEMS
ALL MODEL C COMPACT MODELS FROM AUGUST 2009.
Updates in Pdf format are published regularly on our website www.icoolsport.com
SPECIFICATIONS
COMPACT
Cool
COOLING POWER
3200 Watts
HEATING POWER
RUN (& Max.) POWER @220Volts 5 Amps(12Amps)
RUN (& Max.) POWER @110Volts 10 Amps(22Amp)
HEAT PUMP TYPE
Rotary
EARTH LEAK SAFETY DEVICE
Yes 30 Milliamps
STAINLESS STEEL HEAT
12 plate, silver
EXCHANGER TANK
soldered
ROLLER BEARING WHEELS
Yes
STAINLESS HANDLES
Yes
AREA LIGHTING
Yes 10 Watts
HI RESOLUTION COLOUR
Yes 800 x 480
TOUCH SCREEN
ELECTRICALLY ISOLATED
Yes 25 Litres per
PUMP, S. STEEL SHIELDED
minute pre set
MAXIMUM PUMP CAPACITY
55 Litres Per Min
LOCKING POWER PLUG
3 Pin Heavy Duty
WEIGHT KG / POUNDS
37KG 81 Lbs
DIMENSIONS H. - W. - D. in mm.
545x475x290
DIMENSIONS H. - W. - D. Inches
21.5x18.7x11.4
COMPACT
Dual Temp
3200 Watts
2400 Watts
5 Amps(12Amps)
10 Amps(22Amp)
Rotary
Yes 30 Milliamps
12 plate, silver
soldered
Yes
Yes
Yes 10 Watts
Yes 800 x 480
COMPACT
Twin
5000 Watts
7 Amps(14Amps)
14 Amps(26Amps)
Rotary
Yes 30 Milliamps
12 plate, silver
soldered
Yes
Yes
Yes 20 Watts
Yes 800 x 480
Yes 25 Litres per
minute pre set
55 Litres Per Min
3 Pin Heavy Duty
38KG 84 Lbs
545x475x290
21.5x18.7x11.4
Yes 40 Litres per
minute pre set
85 Litres Per Min
3 Pin Heavy Duty
40KG 88 Lbs
545x475x290
21.5x18.7x11.4
Please note.
iCool Systems are sold all around the world and these specifications may be different for
units delivered in your country due to local conditions or regulations. We are constantly
improving our products and therefore certain specifications may change due to ongoing
research and development.
We welcome your feedback and suggestions and we offer support for general enquiries and
information for specific countries on our website at..
www.iCoolSport.com
Thank you for choosing iCool the world’s most popular ice bath therapy and recovery
systems.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising