User Manual
8 drivers unit
Foldable
PC cable
MORE INFO:
User Manual
[email protected]*
Premium Virtual Surround Sound Bluetooth®
On-the-Ear Headphones
with apt-X"
A
O Bluetooth”
+ aptX is a registered trademark of CSR plc. * The Bluetooth word mark and logos are registered trademarks of Bluetooth SIG, Inc.
SAFETY GUIDELINES
Thank you for purchasing these headphones! For best results,
please thoroughly read this manual and carefully follow the
instructions. Please pay special attention to the safety warnings to
ensure that no harm comes to you or your equipment. Please keep
this manual for future reference.
To prevent noise-induced hearing damage, avoid long-term exposure to
high volume levels.
Do not use while driving, operating heavy machinery, or in any potentially
hazardous situation.
Keep out of reach of small children.
Do not immerse in water or other liquid. Avoid exposure to moisture when
in use.
Do not store or use these headphones in temperatures below +5°F
(-15°C) or above +131°F (+55°C), which can damage the internal battery.
This device contains a lithium polymer battery. Please follow local
regulations and guidelines if disposing the battery.
PACKAGE CONTENTS
After receiving the product, please inventory the contents to
ensure you have all the proper parts, as listed below. If anything is
missing or damaged, please contact Monoprice Customer Service
for a replacement.
* 1 x Bluetooth Headset
* 1 x USB charging cable
* 1 x 3.5mm stereo audio cable
* 1 x Leather storage pouch
* 1 x User Manual
STYLE AND QUALITY
Charging Jack
Volume Down
Next Track
Volume Up/Previous Track
Multifunction (MF) Button
Audio Cable Jack Indication LED Light
EASY CARRYING
Foldable
BATTERY AND CHARGING
This headset has a built-in, nonremovable lithium polymer battery.
The battery is charged using any USB source with at least 400mA
of current. You may use the included USB charging cable or any
other micro USB cable to charge the battery.
1. Ensure that the headset is powered off before attempting to charge
the battery.
2. Plug a micro USB cable into the micro USB port on the headset.
3. Plug the other end of the cable into a USB charging source (wall
charger, computer, battery backup, etc.). The LED on the headset will
glow red while charging is in progress.
4. When the LED turns blue, charging is complete.
OPERATION
Pairing With a Mobile Phone
1. Slide the power switch upward until the green dot shows.
2. If the headset has already been paired with a phone that is powered
on, the headset will connect automatically within a couple seconds.
During the connection process the LED will blink blue regularly. When
the connection is complete the LED will blink several times in rapid
succession, every 5 seconds or so.
3. If the headset has already been paired, but the paired device is
either off or not in range, the LED will blink blue regularly for a few
seconds, then the headset will automatically enter pairing mode,
indicated by the alternate blue and red blinking of the LED.
4. If the headset has not yet been paired with any device, it will
automatically enter pairing mode when it is powered on.
5. Ensure that the phone or other device is within 3 feet of the headset
during pairing.
6. With the headset in pairing mode, open your phone's Bluetooth
settings and start to scan for devices.
7. Select the "R2" entry. If a password is requested, use: 0000 (four
Zeros).
8. Once pairing is complete the two devices will automatically connect
and the LED will flash rapidly about every 5 seconds.
Note: The headset will remain in pairing mode for about 300 seconds. If you fail to
successfully pair the device, turn off the headset, wait 30 seconds, then start over.
CONNECTING TO TWO MOBILE PHONES
You can have the headset simultaneously connected to two
different phones. To do so, perform the following steps:
1. Pair and connect the first phone in accordance with the instructions
in the previous section.
2. Shut off the phone or disable the Bluetooth connection.
3. Turn off the headset, wait for about 30 seconds, then turn it back on.
4. After several seconds of searching for the connection, the headset
Will enter pairing mode automatically.
5. Pair the second phone in accordance with the instructions in the
previous section.
6. Once the second phone is paired and connected, turn on the first
phone or enable its Bluetooth mode, and connect to the headset. You
now have two phones connected at the same time!
DISCONNECTING FROM A MOBILE PHONE
You can disconnect the headset from the phone in a variety of
ways:
Turn off the phone.
Turn off the headset.
Disable the phone's Bluetooth function.
Move the phone at least 66 feet (20 meters) away from the headset.
RECONNECTING THE PAIRED HEADSET WITH
A MOBILE PHONE
1. Ensure that the phone and headset are within 3 feet of each other.
2. Turn on the headset. It will automatically enter reconnection mode.
3. Turn on your phone's Bluetooth search function. The two devices
should automatically reconnect.
Note that with some phones you need to click the "R2" entry to reconnect.
ANSWERING INCOMING CALLS
1. With the headset paired and connected to the phone, the headset
will sound the ringtone when an incoming call occurs.
2. Press the "MF" Multi-Function button once to answer the call or use
the answer function on your phone.
TERMINATING A CALL
1. Press the "MF" button once to "hang up" and terminate the call.
REJECTING A CALL
1. With the headset paired and connected to the phone, the headset
will sound the ringtone when an incoming call occurs.
2. Press and hold the "MF" button for about 2 seconds, then release, to
reject the incoming call or use the call reject function on your phone.
LAST CALL REDIALING
1. To reconnect to the last number you were connected to, press the
"MF" button twice.
PLAYING AND PAUSING BLUETOOTH MUSIC
1. When music is playing through the headset, press the "MF" button
once to pause playback. Press the "MF" button once again to resume
playback.
SKIPPING TRACKS
1. To skip forward to the next track, press the "Vol (-)" button once.
2. To skip back to the previous track, press the "Vol (+)" button once.
VOLUME CONTROL
1. To decrease the volume level, press and hold the "Vol (-)" button.
2. To increase the volume level, press and hold the "Vol (+)" button.
Vol(+) Previous track
Vol(-) Next track
LED indicator
Multifunction button
On/Off Switch
(Right Side)
TECHNICAL SPECIFICATIONS:
* Drive Unit: 1x 50mm and 3x 13mm Neodymium Drivers per earpiece
* Frequency Response: 20Hz - 20KHz
* Bluetooth Version: V4.0
* Supported Profiles: aptX, A2DP, AVRCP, HSP, HFP
* RF Frequency Band: 2.4GHz ~ 2.48GHz
* Operating Range: up to 20m (line-of-sight)
* Battery: 650mAh Li-Polymer Rechargeable Battery
* Bluetooth Music Playback Time: up to 25 hours
* Wired Music Playback Time: up to 16 hours
* Talk Time: up to 28 hours
+ Standby Time: up to 1300 hours (54 days)
* Impedance: 50 ohms and 32 ohms
* Operating Temperature: +14 ~ +122°F (-10 ~ +50°C)
* Weight: 7.4 oz (210g)
Technical specifications are subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement