VDT39 USER MANUAL(EN)
2-Wire Video Intercom System
 Read this manual carefully before using the product, and keep it well for future use.
Introduction
The monitor is designed with 3.9 inch screen, it provides a resolution of
800x480 pixels with high quality image display. The touch sensitive button
makes the operation more easily.
Parts and Function
Microphone
Mounting Hook
LCD Screen
Touch Button
1
ON
2
3
4
6
Talk/Mon Button
Connection Port
DIP
5
Power Indicator
Message Indicator
Don't Disturb Indicator
Unlock Button
Speaker
Terminal Description
1
ON
L1,L2: Bus terminal
SW+,SW-: Door bell call button
connection port
DIP switches: Total 6 bits can be
configured.
Bit1~Bit5: Used to User Code
setting.
Bit6: Set to ON if the monitor is at
the end of the line or works with
DBC4S. Otherwise, set to OFF.
2
3
4
6
DIP
5
1
2
3
DIP
4
SW+
SW-
6
DIP
5
-2-
ON
L1
L2
Unit Mounting
145~160 cm
Accessory contents:
Accessories include a Bracket, two 4X25 screws (use to fasten the Mounting Bracket),
2 wire connectors (use to connect with Monitor).
Installation steps:
Installation height for indoor monitor usually is 145~160cm(refer to sketch map).
Wire the cable correctly(see the later connection chapter) then hang the Monitor on
the Mounting Bracket firmly.
About Main Menu
The main menu is your starting point
for using all the applications on your
monitor. You can customize your
main menu to display applications,
logos, and languages.
Touch the screen on the right
“1,2,3,4” of any one can enter the
home page, the home menu page
will be shown as follows:
Basic Operation Instruction
Answering a Door Call
• Press CALL button on door station.The monitor rings,and the visitor’s image
will be seen on screen.If nobody answers the call,the screen will turn off in
30 seconds automatically.
-3-
• Press TALK/MON Button on monitor, you can communicate with the
visitor for 90 seconds.After finishing
communication,press TALK/MON button again to end the communication.
• During talking state, Press UNLOCK
Button to open the corresponding door
for the visitor.
DS-1 00:30
• When the monitor is in standby mode, press TALK/MON Button(or touch
Monitor ... item on main menu page), the screen can display the view of
outside. If multi door stations are installed, touch
icon,and then touch
or
icon to get into the camera switch mode. You can touch Door/Camera 1/2/3/4 to monitor the door station or CCTV camera you want.See the
following diagrams.(Touch
icon to end monitoring.)
Intercom Function
Intercom function can be initiated by any monitor when multi monitors are installed.
When the monitor is in standby mode, Touch
the screen on the right “1,2,3,4” of any one
can enter the home page, the home menu
Intercom
page,there are three items:
Call...,
Inner Call ...,
Call Guard Unit...
Intercom Call: User in one apartment can call
other apartments in the system. the namelist
will be created automatically by the system.
Touch a name you want on the screen, then
touch Dial icon to dial.(Note:The DIP switches
code of each monitor must set different.)
Inner Call: If multi slave monitors are installed
in the same apartment, select Inner Call, all the other Monitors will ring at the
same time, whichever Monitor answers the call, conversation is started.and
the other monitors will stop ringing at the same time.(note:the DIP switches
setting of all monitors must be same. )
-4-
Call Guard unit: A Monitor can be assigned as Guard Unit Monitor; when the
Guard Unit Monitor answers the call, conversation with the guard person is
started.
Other Function:
Call Transfer item on main menu page to
1.Call Transfer function:Touch
enter call transfer page,and then you can select the item you want.
Light item on main menu page to enter light func2.Light function:Touch
tion page,and then you can select the item you want.
Playback item on main menu page to enter
3.Playback function:Touch
playback function page,and then you can select the item you want.
Basic Setup Instruction
Ring Tone Setting
Setup item on
Select and touch
main menu page,and then select
Ring Tune to enter setup page.
Select DS, Intercom or Door Bell
item, There are 12 pieces ring tones
can be selected.Use Inc/Dec button
to select last/next ring tone, press
Exit button to save and exit.
Ring Tune
Ring Volume
Monitor Time
Exit
DS: set the ring tone calling from
outdoor station.
Intercom: set the ring tone calling
from other apartments.
Door Bell: set the ring tone calling
from door bell.
Tune Select
Inc
Dec
Current:
01
Exit
Ring Volume Setting
Setup on
Select and touch
main menu page, then select Ring
Volume... item, the setting range is
/
0~9. Use
button to increase
/ decrease the value, press Exit button to save and return last page.
Adjust Value
Current:
3
-5-
Monitor Time Setting
Setup on main
Select and touch
menu page, then select Monitor
Time... item. Use
/
button to
increase / decrease the value, press
Exit button to save and return last
page.
Adjust Value
Current:
30sec
Menu Language Setting
Maximum 16 languages can be supported by the monitor.
0
On main menu page, select
About->Language.The languages that
the monitor supported will be displayed, and the current language will
be shown “√ ”.
Screen Setting
During monitoring or talking state,
Adjust button,the adjust
press
menu will be displayed.
There are 3 adjustment items can be
selected:
The first item is Scene mode selection: Total 3 screen modes can be
selected in sequence: Normal,Bright
and Soft .
Brightness item is for the
The
image quality setting, adjust the value
to get the best image you like.
Volume item is for the talk
The
volume setting.
-6-
H/W:
a1.2
Language
S/W:
00.01.00
Restore
Addr:
00.01
Video STD: AUTO
DS-1 00:30
DS-1 00:30
• Note that all the modifications will be done immediately after the operation.
Press
button to quit the adjust page.
Restore to Default
About->Restore. If touch
On main menu page, select
icon ,All settings will be restored to default, if you don't want to restore, touch
icon to
cancel the operation.(Note that the restore to default operation will not change
the time setting and the datas.)
H/W:
a1.2
Language
S/W:
00.01.00
Restore
Addr:
00.01
Video STD: AUTO
Installation Setting
Enter Installation Setup Page
Step1: Touch
About on main menu page ,then press UNLOCK button
and hold for 2s enter Installer Setup page.
Step2: Input 4 digits number according to the information.
Step1
Step2
Installer Setup
[0000]
Inc
Dec
Next
Press unlock to exit !
Confirm
-7-
The setting items are as followings:
[8000]:Master 0[8001]~[8003]:Slaver 1~3
[8004]:Guard unit
[8005]:Not guard unit
[8006]:Panel on as slaver called
[8007]:Panel off as slaver called
[8014]:Unlock menu on [8015]:Unlock menu off
[9006]:Simplified version
[9007]:Full-featured version
How to set the monitor as a Guard Monitor
A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Monitor answers the call, conversation with the guard person is started.
The code number of 8004 is used to set the monitor as a Guard Unit Monitor
and 8005 is used to cancel this function. (Not Guard Unit is default setting.)
How to set the slave monitor address
Maximum 4 monitors can be connected in one apartment,one master monitor together with 3 slave monitors, so you should set the address correctly.
(note:must have one monitor to be set as master monitor)
The code of 8000 is used to set the master monitor(by default).
The code of 8001 is used to set the first slave monitor .
The code of 8002 is used to set the second slave monitor .
The code of 8003 is used to set the third slave monitor .
How to set the monitor panel on
In default mode,when receive a calling,the master and slave monitors will
ring at the same time,and just the master monitor can display the image while
the slave monitors can not.But the settings can be changed,you can set the
master monitor and all the slave monitors to panel on at the same time when
receiving a call, just input the code number of 8006 on each slave monitor.
Press call button
on door station
When reveiving calling,all monitors can display the image at the same time
Master monitor
-8-
#1st slave monitor
#2nd slave monitor
#3rd slave monitor
How to set 2 locks control
The monitor can be set to control 2 locks while you should set the unlock
menu item to “on “ state.
The code number of 8015 is used to set the unlock menu off (by default) that
it can only control one lock.
The code number of 8014 is used to set the unlock menu on that it can control
two locks.
Note:
1. During talking or monitoring state, press
UNLOCK button,two unlock icons will be
shown. Select the item you want, and then
it will release the corresponding door(The
code number of 8014 is used to set the unlock menu on).
2. Note that the restore to default operation
will not change the parameters setting.
DS-1 00:30
How to set the main menu version
There are two main menu version to choose for the monitor:Full-featured version and Simplified version(by default) .
The code of 9006 is used to set the simplified version main menu(by default).
The code of 9007 is used to set the full-featured version main menu.
Specification:
• Power Supply: DC 20-28V
• Power Consumption: Standby 0.286W; Working status 3.224W
• Monitor Screen:
3.9 inch digital color TFT
• Display Resolutions:
800(R, G, B) x 480 pixels
• Video Signal: 1Vp-p, 75Ω, CCIR standard
• Wiring:
2 wires, non-polarity
• Dimension:138(H)×138(W)×19(D)mm
-9-
Precautions
1) All components should be protected from violence vibration. And not allow
to be impacted, knocked and dropped.
2) Please do the cleanness with soft cotton cloth, please do not use the organic impregnant or chemical clean agent. If necessary, please use a little
pure water or dilute soap water to clean the dust.
3) Image distortion may occur if the video monitor is mounted too close to
magnetic field e. g. Microwaves, TV, computer etc.
4) Please keep away the monitor from wet, high temperature, dust, caustic
and oxidation gas in order to avoid any unpredictable damage.
5) Must use the right adaptor which is supplied by the manufacturer or approved by the manufacturer.
6) Pay attention to the high voltage inside the products, please refer service
only to a trained and qualified professional.
-10-
Note
-11-
The design and specifications can be changed without notice to the user. Right to
interpret and copyright of this manual are preserved.
Download PDF