DUAL TECHNOLOGY DETECTOR

DUAL TECHNOLOGY DETECTOR
User Manual
SIT-1212W
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON
THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
English _2
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
English _3
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
Please read the following recommended safety precautions carefully.
y Do not Place this apparatus on an uneven surface.
y Do not install on a surface where it is exposed to direct sunlight, near heating equipment or in extremely cold area.
English _4
y
y
y
y
y
y
Do not place this apparatus near conductive material.
Do not attempt to service this apparatus yourself.
Do not place a glass of water on the product.
Do not install near any magnetic sources.
Do not block any ventilation openings.
Do not place heavy items on the product.
User’s Manual is a guidance book on how to use the products
The purpose of using symbols in the manual is as follows:
y Reference: To provide information for help in usage of products
y Notice: If any possibility exists to cause damage to goods/persons as a result of not following the instructions
Ú Please read this manual for the safety before using goods and keep it in the safe place.
Note
1.
Please install and use the detector following the directions. Do not touch the sensor surface as this could result in a
detector malfunction.
If necessary, clean the sensor surface using a soft cloth with pure alcohol.
English _5
2.
Avoid using products in areas with huge change of temperature.
3.
The user should follow the installation and operation instructions and among other things test the product and the
whole system at least once a week. For various reasons, including, but not limited to, changes in environmental
conditions, electric or electronic disruptions and tampering, the product may not perform as expected. The user is
advised to take all necessary precautions for his/her safety and the protection of his/her property.
Product Features
y
y
y
y
y
y
y
y
y
y
y
y
Adopted MCU
Automatic pulse count
Streamline design
Doppler + Power analysis
X-Band plane antenna
Microwave detecting range adjustable
Auto temperature compensation reducing false alarm
Valve adjustable technology with high anti-interference
Unique look-down design without dead angle
N.C./N.O. optional for different alarm
Intelligence technology differing intruder from interference signals
SMT technology
English _6
IR Sensor at a Glance
1. Wire exit
2. Terminal block
3. Microwave module
4. Yellow LED
5. Red LED
6. Green LED
7. LED jumper
8. RELAY jumper
9. P.COUNT jumper
10. Dual PIR
11. Microwave VR
12. Tamper
English _7
Installation
1.
Fix detector bracket to wall. Remove front cover of detector, take out PCB, fix back cover to bracket with screws
(the best installation height is about 2.2m).
2.
Set the PCB in the back cover after connecting the wires according to the TERMINAL BLOCK FIGURE full stop
close the front cover.
3.
Avoid installing the detector close to the following sources of interference: reflective surfaces, direct air flow from
vents, fans, windows, sources of steam, oil vapor, infrared light sources and objects causing temperature changes
such as heaters, refrigerators and ovens. Avoid installing the detector in the direct sunlight.
4.
Ensure no object is in front of the lens of the detector, the look-down window must face down.
English _8
Testing and Usage
1.
With 12V power supply, the detector is set into self-checking state and the LED ON; the LED is off after 60
seconds and the detector is set into operating state.
2.
Conduct walk test in detecting range, different LED ON: Green LED ON, infrared is ON; Yellow LED ON,
microwave is ON; Red LED ON, infrared & Microwave is ON and the detector is in alarm status.
3.
RELAY jumper is used to set alarm output mode. Select different output mode depending specification of control:
1&2/N.C. ; 2&3/N.O. . (1&2/N.C. is set as factory default.)
4.
Microwave VR is used to adjust the detecting range of microwave according to customer's request. (The largest
detection range is set as factory default.)
5.
LED jumper is used to control LED indication without interference to detector. LED ON jumper can be interrupted
after testing for concealment.
6.
P.COUNT jumper is used to select the first and second pulse.
Connect 1&2 to 1P (the first pulse), 2&3 to 2P(second pulse).
The fisrt pulse generally used in normal circumstances, and the second pulse used in relatively harsh
circumstances. (First pulse is set as factory default.)
English _9
Terminal Block
•
•
•
•
+12V: DC ANODE
GND: DC CATHODE
ALARM: RELAY OUTPUT PORT
TAMPER: TAMPER OUTPUT PORT
Detecting Range
YUY”
WU\”
Z”
\”
Side view
ALARM +12V GND TAMPER
Top view
English _10
^”
XY”
Specifications & Appearance
Specifications
Item
Description
Detection Range
110° x 12m
Installation Height
2.2m
Auto Temp. Compensation
O
Pet immunity
–
PIR Sensitivity
O
Selectable Pulse Count
O
Input Voltage
DC 9V ~ 16V
Current
≤30mA
Power Consumption
0.36W (DC12V)
English _11
Item
Description
Alarm Output
N.C/N.O
Tamper
O
Operating Temperature
-10~+50˚C
Operating Humidity
95% max
Dimensions (W x H x D)
130 x 65 x 53.3mm
Weight (g)
133g
English _12
Appearance
130.0
53.3
53.3
65.0
English _13
Unit: mm
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to
provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and
indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Download PDF