SZSINO-SHINE (HK) LIMITED
华 炫 (香 港) 有 限 公 司
Address: 9th Building, 1st Block, Taoyuanju, Baoan District, Shenzhen, China, 518126
Tel: 86-755-29922332
Fax: 86-755-29922459
Website: www.gpstracker911.com
cell: 86-13802554182 Email: marketing@gpstracker911.com
GPS VEHICLE TRACKER
VT106 USER MANUAL
Preface
Thank you for purchasing the TK106 GPS vehicle tracker. This manual shows how to operate the device
smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that
specification and information are subject to changes without prior notice in this manual. Any change will be
integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this
document.
www.gpstracker911.com
1
Content
1 Summary functions
--------------------------------------------------------------------------------------------------
3
2 Application
--------------------------------------------------------------------------------------------------
3
3 Hardware description
3.1 Front face -----------------------------------------------------------------------------------------------------
3
3.2 Rear face
----------------------------------------------------------------------------------------------------
3
3.3 Side face
-----------------------------------------------------------------------------------------------------
4
3.4 Bottom face -----------------------------------------------------------------------------------------------------
4
4 Specifications
------------------------------------------------------------------------------------------------------
4
5 Usage
5.1
SIM card installation
-------------------------------------------------------------------------------------
5
5.2
GPS Vehicle Tracker Installation -------------------------------------------------------------------------
5
5.3
Startup
6
5.4
Restart the tracker ----------------------------------------------------------------------------------------
6
5.5
Initialization
7
5.6
Change or resume password
5.7
---------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------------------------------------------------------
7
Authorization
--------------------------------------------------------------------------------------
7
5.8
Set time zone
---------------------------------------------------------------------------------------
7
5.9
Wire-tapping and Tracking modes
-------------------------------------------------------------
7
5.10
SOS button
----------------------------------------------------------------------------------------------
8
5.11
Geo-Fence
----------------------------------------------------------------------------------------------
8
5.12
Movement alert
------------------------------------------------------------------------------------------
8
5.13
Over-speed alert
-----------------------------------------------------------------------------------------
8
5.14
Low battery alert
-----------------------------------------------------------------------------------------
5.15
Real-time positioning
5.16
Auto track by SMS/cellphone
---------------------------------------------------------------------------
9
5.17
Auto track by GPRS/platform --------------------------------------------------------------------------
9
5.18
Set homepage as advertisement
-----------------------------------------------------------------------
10
5.19
IMEI checking
--------------------------------------------------------------------------------------------
10
5.20
Count mileage
--------------------------------------------------------------------------------------------
10
5.21
Remote control oil and circuit
----------------------------------------------------------------------
10
5.22
Alarm frequency setup------------------------------------------------------------------------------------
11
5.23
Read password
11
5.24
Get Location in Detailed Street address --------------------------------------------------------------
11
5.25
Power-lost alert
11
5.26
Auto Sleeping mode -----------------------------------------------------------------------------------------
6 Cautions
9
----------------------------------------------------------------------------------
9
--------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
11
------------------------------------------------------------------------------------------------------------
11
------------------------------------------------------------------------------------------------------
12
----------------------------------------------------------------------------------------------------
12
------------------------------------------------------------------------------------------------
13
7 Trouble Shooting
8 SMS Command list
9 Configure tracker steps
www.gpstracker911.com
2
1 Summary function
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any
remote targets by SMS or GPRS.
1.1 Positioning and Tracking: through GPRS (on-line web tracking platform) or SMS to locate the targets, get
the targets’ working status, and showing onto Google map.
1.2 Triggering Emergency Alarm: when there is an emergency or accident happened to the vehicle, driver can
put on the SOS button and the GPS unit will send out alarm to the authorized numbers and the monitor center.
1.3 Remote stop/resume oil power supply: you can remotely stop/resume oil power supply circuit by SMS
command anywhere and anytime, and further to further stop/resume car.
1.4 Wire-tapping: In anywhere and anytime, call to SIM card number in the GPS unit, you can monitor the
listen and see what happen 5 meters around the GPS tracker.
1.5 Movement Alert: Send SMS to the unit to start the movement alert function when car in parking mode.
When the vehicle is moving, the unit will send the movement alert to all authorized numbers.
1.6 Over-speed Alert: Send SMS to the unit to start the over-speed alert function. When the vehicle is beyond
the speed limit setup, the unit will send the over-speed alert to all authorized numbers.
1.7 Geo-fence: Set up a geo-fence for the unit to restrict its scope within a given range. The unit will send the
message to all authorized numbers when it breaches the district.
1.8 Reset: send SMS to resume the default of unit.
1.9 Auto Track: You can set up auto track by SMS or GPRS tracking.
1.10 Mileage statistics: ACC checking, cutting off power and alarm.
1.11 Compatible with the original anti-theft alarm: It will send SMS alarm after the car original anti-theft alarm
warning.
1.12 Modify the IP and COM Port of Communication Protocol for different on-line web tracking platform.
2 Application

Car rental business control

Vehicle fleet management

Taxi fleet management

Protect asset etc
3 Hardware Description
3.1 Front face
www.gpstracker911.com
3.2 Rear face
3
3.3 Side face
Indicator for signal
Mini-USB port
GPS Antenna
GSM/GPRS
Antenna
3.4 Bottom face
Press this hole to popup
the SIM card slot.
Microphone jack
SIM Card slot
Wire box
4 Specifications
Content
Dim.
Weight
Network
Band
GPS chip
GSM/GPRS
module
GPS sensitivity
GPS accuracy
Time To First Fix
Work voltage
Battery
Standby
Storage Temp.
Operation Temp.
Humidity
www.gpstracker911.com
Specs.
85mm x 63mm x 25mm(3.3”*2.5”*0.98”)
160g
GSM/GPRS/GPS
850/900/1800/1900Mhz
SIRF3 chip
Simcom900B
-159dBm
5m
Cold status
45s
Warm status 35s
Hot status
1s
10V—36V
Chargeable changeable 3.7V 1500mAh Li-ion battery
48hours
-40°C to +85°C
-20°C to +55°C
5%--95% non-condensing
4
5 Usage
5.1 SIM card installation
Make sure that there is no call transfer and caller ID function is on, and PIN code off. The SMS message
must in Text format, can’t be identified for PDU format.
5.1.1 Put SIM card into SIM card slot.
5.1.2 Put the SIM card into slot as the picture below.
.
5.2 GPS Vehicle Tracker Installation
GPS/GSM/GPRS tracker should be installed by professional technician. Without permission, the user can’t
repair and breakup the tracker. Otherwise, warranty policy would be broken and invalid.
5.2.1 Install Wire box
5.2.2 GPS Vehicle Tracker Installation
www.gpstracker911.com
5
Installation steps (caution: the following installation should under no power, otherwise will be dangerous)
Wire for cutting off oil power supply of the car
Yellow wire connects to the relay feet 86, connect 85
feet to 12 V DC anode, connect 87 feet and 30 feet in
series to the oil power supply circuits.
Wire for cutting off oil power supply circuit of the car
White wire connects relay feet 86; 85 feet to 12 V DC
anode, 87 feet and 30 feet are in series in the supply
power circuits.
Emergency/SOS triggering alarm
The blue wire connects to the anode of the alarm
button, and the black wire connects to the cathode
Power supply line
The red wire connects 12V“+”; Black wire
connects to12V“-”
of the alarm button.
Steps: 1. Open the rear cover, and pick out the battery.
2. Push the foil along and turn it left.
5.3 Startup
5.3.1
Install the tracker in the car, then put the SIM card into the slot, go outdoors to get GSM network signal.
5.3.2
For first use, please initialize the unit and restore it to default setting.( please refer to 5.4 for instruction.)
5.3.3 In 10 or 40 seconds, the unit will begin to work and acquire the GSM signal as well as the GPS signal,
and the red indicator will keep flashing every 2 seconds when the GPS is in standby mode. When the blue
indicator is keep blinking, it means the unit has been located.
5.3.4 When unit receives GPS signals normally, you can use it and do all the following settings.
Notice: when SIM card slot insert in, tracker would be in power on mode automatically.
5.4 Restart the tracker.
Send SMS "reboot+password" to the tracker. If success, it will reply "system will reboot…", tracker will be
restarted. (original password is defaulted as 123456)
www.gpstracker911.com
6
5.5 Initialization
Send “begin+password” in text SMS to the unit, it will reply “begin ok” and initialize all the settings. (Default
password is 123456)
5.6 Change or resume password
5.6.1 Send SMS "password+old password+ space +new password” to change the password.
Remark: Make sure the new password is in 6 digits, or else the tracker can’t recognize the password.
5.6.2 you can Send "resumepassword" to the tracker, to restore the original setting in case of losing the new
password, and it will reply "resume password,password is123456".
Remark: Please keep in mind of the new password, because most of the instructions need the password.
5.7 Authorization
There are 5 numbers can be setup as authorized numbers to get location information and monitor the car.
5.7.1 Call the tracker for 10 times, it will make the cell phone number as the authorized number automatically.
5.7.2 Send SMS "admin+password+space+cell phone number" to set up an authorized number. The other
authorized numbers should be set by the first authorized number. If the number is successfully authorized, the
unit will reply "admin ok!" in SMS.
5.7.3 Send SMS "noadmin+password+ space +authorized number" to delete the authorized number. If the
number is successfully authorized, the unit will reply "no admin ok!" in SMS.
Notice: For roaming purpose, you have to add your country code ahead of the cell phone number, for example,
please "send admin123456 008613311113333" to tracker to set 13311113333 as an authorized number.
5.8 Set Time zone
In order to make the time conforming with the user’s country time zone, please send SMS command "zone+password+space
+time zone". For example, if user country time is GMT+8, then send "zone123456 +8"to the device. If user country time is
GMT-6, then send"zone123456 -6"to device. The device will reply SMS "set time zone ok".
Remark: if time zone is +, in SMS command, + can be neglected.
5.9 Modes switch between "normal tracking" and "wire-tapping"
5.9.1 The default mode is "normal tracking".
5.9.2 Send SMS "monitor+password" to the unit, and it will reply “monitor ok!” and switch to “wire-tapping”
mode. In this mode, user can dial up to tracker to listen what happen around tracker.
5.9.3 Send SMS "tracker+password" to the unit, it will reply “tracker ok!” and restore to “normal track”
mode.
www.gpstracker911.com
7
5.10 SOS button
5.10.1 Press the SOS for 1 second, it will send "help me !+GPS coordinates" to all the authorized numbers
every 3 minutes. It will stop sending such a SMS when any authorized number reply SMS "help me !" to the
tracker.
5.10.2 Send SMS “nosos+password” to tracker, it will reply "nosos ok", after that it will not send alarm info.
5.11 Geo-fence
Set up a geo-fence for the unit to restrict its scope within a given range. The unit will send the alert message to
the authorized numbers when it breaches the district.
5.11.1
Run
out
of
the
Geo-fence
setup:
Send
SMS
"stockade+password+space+latitude+,+longitude+;+latitude+,+longitude+1” to tracker to set the Geo
fence, if succeed, it will reply "stockade ok".
For example, send "stockade123456 22.100000N,113.100000E;22.900000N,113.900000E1” to set up a
Geo-fence, when car run out of this range, tracker will alert to authorized telephone or platform.
5.11.2
Run
into
the
Geo-fence
setup:
Send
SMS
"stockade+password+space+latitude+,+longitude+;+latitude+,+longitude+2” to tracker, if succeed, it will
reply "stockade ok".
For example: send "stockade123456 22.100000N,113.100000E;22.900000N,113.900000E2" to setup a
Geo-fence, when car run into this range, tracker will alert to authorized telephone or platform.
Remark: The first latitude & longitude is coordinate of the top left corner of the Geo-fence, while the second
latitude &longitude is the coordinate of the bottom right corner. It will alarm 3 times at 3 minutes time interval.
5.11.3 Cancel: Send SMS "nostockade+password" to deactivate this function, it’ll reply "no stockade ok".
This function will be out of effect after the unit moves outside the district.
5.12 Movement alert
5.12.1 Set up: When the unit stays immobile in a place for 3 minutes, user can send SMS "move+password" to
the unit, then the unit will reply “move ok!”. After 10s, if tracker moves over 200m, it will send SMS
"Move+GPS coordinates" to the authorized numbers or platform. It will alarm for 3 times every 3 minutes.
5.12.2 Cancel: Send SMS "nomove+password" to deactivate the movement alert.
Remark: This function will be out of effect after the unit moves outside the district.
5.13 Over-speed alert:
5.13.1 Set up: Send SMS "speed+password+ space +080" to the unit (suppose the speed limit is 80km/h), and
it will reply "speed ok!". When the target runs exceeding 80km/h, tracker will send SMS "speed+080!+ GPS
coordinates " to the authorized numbers. It will alarm for 3 times every 3 minutes.
5.13.2 Cancel: Send SMS “nospeed+password” to deactivate the over-speed alert
Remark: It is recommended that the speed limit is set at no less than 50km/h.
www.gpstracker911.com
8
5.14 Low battery alert
It begins to alert when voltage reaches lower than 3.7V and sends you SMS in 30 minutes interval. SMS format
“low battery+GPS coordinates”.
5.15 Real-time polling
5.15.1 If there is no authorized number, when any number dials up the unit, it will report GPS coordinates. If
there is already an authorized number, then it will not respond when an unauthorized number calls it up.
5.15.2 When an authorized number dials up the unit, it will hang up and report real-time GPS coordinates.
5.16 Auto Track by SMS/cellphone
Report GPS coordinates at 30s intervals to the authorized numbers for 15 times:
5.16.1 Set up tracking time intervals: send SMS "at30sum15 " to the unit, it will report the GPS coordinates at
30s intervals for 15 times. The setting must be maximum 999999 in value.
5.16.2 Set up constant tracking: send SMS "at30sum0" to tracker, it will report GPS coordinates at 30s
intervals all the time automatically till user cancel auto track.
5.16.3 Cancel auto track: send noat+password to cancel the “auto track” by telephone.
5.16.4 Send SMS "telephone+password" to tracker. If set successfully, tracker will reply “set telephone ok”.
And then, tracker will send GPS coordinates to your telephone by SMS.
Remarks: 1. the default mode is “telephone/SMS tracking”. 2. If lose GPS signal, authorized phone number
will get GPS coordinates at 0.
5.17 Auto tracking by GPRS/web-tracking platform
5.17.1 Initialization: send SMS “begin123456” to tracker, it will reply “begin ok” and initialize all the
settings. (default password is 123456).
5.17.2 Set time intervals: send SMS "at30sum15" to the unit, it will report the GPS coordinates at 30s
intervals for 15 times. Send "noat+password" to Cancel “auto track ”.
Remark: 1.the interval must between 20 and 999999,
2.sum0 is heaps of times (means constantly sending GPS coordinates to platform).
5.17.3 Setup device ID/number to web-tracking platform: send SMS "number+tracker ID" to the tracker, it
will reply "set number ok". For example, if you want setup your tracker ID against your platform as
20101123001, the SMS should be “number20101123001”. Note that tracker ID must be within 11 digits.
5.17.4 Set GPRS/web-tracking mode: Send SMS "web+password" to tracker. If set successfully, tracker will
reply SMS "set web ok". The device will send GPS coordinates to Server/IP address by GPRS.
www.gpstracker911.com
9
5.17.5 Set up IP address and port: send SMS " ip +ip address+port +port number" to tracker. If setup
successfully, tracker will reply SMS "set ip address and port ok". For example, if the platform IP address and
port number is 116.255.131.00 and 8500, send SMS "ip116.255.131.00port8500"to the tracker.
Cancel: Send SMS “noadminip+password”, to cancel the IP address already setup, it means tracker will only
send GPS coordinates to user by SMS, not by GPRS anymore.
5.17.6 Set APN:
In order to send GPS data to IP address, you must set mobile network APN (Access Point Name). If you don’t
know the APN, you can consult local network service supplier. The format of APN setup SMS is "apn +
password + space + apn name". For example the China Mobile APN name is “cmnet”, send SMS
"apn123456 cmnet" to the device. The device will reply SMS "Set APN ok. " .
5.17.7 Set up APN user name and password:
Send SMS "user+password+Space+apn name+Space+apn password"to set the APN user name and
password. If setup successful, the tracker will reply SMS “set GPRS user and password ok”. For example, in
China, we’ll send SMS “user123456 cmnet cmnet” to tracker, first cmnet stands for APN user name, and
second cmnet stands for APN password.
As soon as the IP & Port & APN name& APN user name and password are set up, tracker will report the
GPS coordinates to IP address/Server by GPRS data packet.
5.18 Set Homepage as Advertisement
In order to see your company website in each replying SMS to your clients in advertising purpose, for example
you website is www.nn.com, then send "home+password+ www.nn.com", then tracker will reply "set home
ok", when you want to cancel it, just send "nohome+password", it will reply SMS "cancel home ok".
5.19 IMEI Checking
Send SMS "imei+password" to tracker to check the IMEI number. Tracker will replay back SMS with IMEI
number.
5.20 Count mileage
5.20.1 Dials up to tracker, it will report a GPS coordinates of which includes mileage info.
5.20.2 You can sent "clearmile+password", if set successfully, it will reply SMS "clearmile GPS coordinates
of which includes mileage info ok", the mileage changes to zero.
5.21 Remote control oil and circuit
5.21.1 Control oil
Send SMS "stopoil+password" to stop oil supply. For example send SMS:stopoil123456
To resume the oil supply again, send SMS "supplyoil+password" to the unit.
5.21.2 Control circuit
www.gpstracker911.com
10
Send SMS "stopelec+password" to control circuit. For example send SMS: stopelec123456
To resume the circuit again, send SMS "supplyelec+password" to the unit.
If there is no authorized telephone number, all the other telephone can control. If there is already an authorized
number, only the authorized number can control.
5.22 Alarm frequency setup
The SMS command "alarm+times value" to setup alarm frequency/times.
For example, send SMS "alarm3" to tracker, if succeed, tracker will reply “Alarm time ok”. Tracker will
alarm 3 times to handset (by SMS) or platform (by GPRS) every 3 minutes, then stop when occur alarm. The
time value shall be in between 1-999, that is, “alarm1”~~”alarm999” are all effective.
Notice, the interval of alarm is defaulted at 3 minutes.
5.23 Read password
This SMS command "readpaw" is to read the password from unit when user forget the password setup.
For example, send SMS "readpaw" to tracker, if success, tracker will reply “Password is ******.”.
5.24 Get Location in Detailed Street address by SMS (under platform map function)
This SMS command “fix+password” is to get detailed street address of location info by SMS.
For example, send SMS "fix123456" to tracker, if success, tracker will send back with detailed street address
location information.
5.25 Power-lost alert
If cut the connection in between tracker and car battery, tracker will send SMS alert "Cut power Alert+ GPS
coordinates" to authorized telephone number or platform.
5.26 Auto Sleeping mode
5.26.1 After car stop for 3 minutes, tracker auto enter into sleeping mode, for power and GPRS fee saving. Car
ACC/Engine start would trigger it back to normal working mode.
5.26.2 If tracker can’t get GPS located longer than 5 minutes, tracker would auto enter into sleeping mode, so,
please don’t setup constant tracking time interval longer than 5 minutes = 300 seconds.
6 Cautions
6.1 Make sure to read this manual carefully before using this product.
6.2 Please insert the SIM card before installation, and make sure the SIM card has no password, otherwise the
tracker will not work normally.
6.3 The tracker’s working voltage is 10V-36V. Please use the tracker in the scope of voltage.
6.4 Please make sure that all the cables of the tracker have been connected rightly, and then connect the tracker
to host power from car battery.
6.5 The tracker works in wireless communications, to avoid electromagnetic interference or incompatible
configuration, please stop using your tracker in the noticed place.
6.6 Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry.
6.7 Clear the unit with a piece of dry cloth. Don’t clean in chemicals or detergent.
6.8 Don’t disassemble or refit the unit.
6.9 Handle carefully. Don’t vibrate or shake it violently.
6.10 Don’t use & store the unit in dusty places.
www.gpstracker911.com
11
7. Trouble Shooting
Faults
Solution
Startup Fail
Check the battery and see if it is fully charged or correctly installed.
Hang up Fail
After a number has been authorized and an unauthorized number calls to device,
it will not hang up. Please initialize the device and re-set the authorized numbers.
Monitor Fail
Check if the authorized number is setup or in the coverage of signals.
Location report in
Don’t use it in the place no signals. Place the unit outdoors under open sky,
especially when starting it up.
digits of zeros.
8 SMS Command list
No
FUNCTION
1 Restart the tracker
2 Initiation
3
Change password
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
SMS
SMS REPLY
System will reboot…
reboot+password (defaulted 123456)
begin ok
begin+password
password+old password+ space +new
change password ok
password
resume password,
Resume password
resume+password
is password123456
Authorize
telephone admin+password+space+time zone+cell
admin ok
number
phone number
noadmin+password+ space +authorized no admin ok
Delete number
number
Set time zone
zone+password+space +time zone
set time zone ok
Monitor mode
monitor+password
monitor ok
Tracking mode
tracker+password
tracker ok
SOS alert
help me!+geo-info
Cancel SOS
nosos+password
nosos ok
stockade+password+space+latitude+,+lo stockade ok
Run Out of Geo-fence
ngitude+;+latitude+,+longitude+1
stockade+password+space+latitude+,+lo stockade ok
Run Into Geo-fence
ngitude+;+latitude+,+longitude+2
no stockade ok
Cancel geo-fence
nostockade+password
move ok
Movement alert
move+password
cancel move ok
Cancel movement alert nomove+password
speed ok
Over-speed alert
speed+password+space+080
cancel speed ok
Cancel over-speed alert nospeed+password
Telephone mode
telephone+password
set telephone ok
auto track set ok
Auto tracking
at30sum0
cancel auto track ok
Cancel auto track
noat123456
Add
number
to
number+tracker ID
set number ok
platform
Web mode
web+password
set web ok
set ip address and port
Set IP
ip +ip address+port +port number
ok
nd
Set 2 IP
Available later
www.gpstracker911.com
CHAP
5.4
5.5
5.6.1
5.6.2
5.7.2
5.7.3
5.8
5.9.2
5.9.3
5.10.1
5.10.2
5.11.1
5.11.2
5.11.3
5.12.1
5.12.2
5.13.1
5.13.2
5.16.3
5.17.2
5.17.2
5.17.3
5.17.4
5.17.5
12
26
28
29
30
Set APN
Set APN user name and
password
Set homepage as adv.
Cancel homepage
IMEI checking
apn + password + space + apn name
user+password+Space+apn
name+Space+apn password
home+password+ www.nn.com
nohome+password
imei+password
29
Count mileage
Dial up to tracker
30
31
32
33
34
35
36
37
Clear mileage
Stop oil
Supply oil
Stop circuit
Supply circuit
Alarm frequency
Read password
Get address by SMS
clearmile+password
stopoil+password
supplyoil+password
stopelec+password
supplyelec+password
alarm+times value
readpaw
Fix123456
27
set APN ok
Set GPRS user
password ok
set home ok
Cancel home ok
IMEI no
GPS
coordinates
+mileage info
clearmile ok
stopoil ok
supplyoil ok
stopelec ok
supplyelec ok
Alarm number ok
Password is ******
Street address
5.17.6
5.17.7
5.18
5.18
5.19
5.20.1
5.20.2
5.21.1
5.21.1
5.21.2
5.21.2
5.22
5.23
5.24
Remarks:
1.123456 is the original password.
2.Whe first using, please put the device to the outdoor where have strong GPS signal, then begin to track after
two minutes.
3.The English capital letter and lowercase letter represent the command, English capital letter is the setting
content, please using lowercase letter to edit all commands by telephone.
9 Use Configuration tool to setup GPRS
Before install tracker to car/vehicle, please firstly test and configure it at your office. Otherwise, it may cause
trouble after installation.
9.1 Put out the SIM card slot in the box, and insert it(without SIM card only slot) into the tracker to trigger
power to be on, red indicator would be keeping flash every 2 seconds when GPS module is in standby mode.
9.2 Connect GPS & GSM antenna, and put antennas out door and under open sky, to get better GPS signal.
Once tracker located, blue indicator would keep blinking every second, after that you can make the
configuration against your PC/Notebook.
9.3 Connect mini-USB to USB cable to tracker and your PC/Notebook (mini-USB to tracker and USB to your
PC/Notebook), open the file <USB Driver V3.0.exe>.
9.4 Find out the right COM Port from the hardware manager of your PC/Notebook.
www.gpstracker911.com
13
9.5 Double click <GPS Tracker Setting Tool>
9.6 GPS Tracker Setting Tool window bar chart
Make configuration as the real situation of your web-tracking platform.
1
2
3
4
5
6
Device ID 5.17.3
APN 5.17.6
Set IP/Port 5.17.5
Geo-fence 5.11
Set password 5.6
Authorize telephone number
7
ACC test
17
8
9
10
Time zone 5.8
Over-speed 5.13
Read device version
18
19
5.7
11
12
13
14
15
16
Initiation/Reset 5.5
Web/GPRS mode 5.17.4
Telephone/SMS 5.16.3
Stop oil 5.20
Stop circuit 5.20
Bands choice
Setup APN user name & password if necessary
5.17.7
Choose COM port and press OPEN
Data of operate result
9.7 You may also follow by the SMS command list to setup by SMS commands.
9.7.1 Get out the SIM card slot, and put your SIM card in. And put the Slot with SIM card into tracker.
9.7.2 Once GPS and GSM signal ready to work, you may try every SMS command to make setup and get GPS
coordinates + URL link.
www.gpstracker911.com
14
Download PDF