GD00Z-8-GC
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER with TILT SENSOR
Installation Instructions
or dial
3
PRODUCT COMPONENTS
GD00Z-8-GC
POWER
INPUT
JACK
STATUS
INDICATOR
CONNECTION
WIRES
OPTIONAL
ADJUSTABLE
GD00Z-8-GC
MOUNTING BRACKET
TILT
SENSOR
SCREWS AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-8-GC-GC - P/N: 10025383 Rev-B- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
WIRE
TIES
WARNING
LIGHT
LINK
BUTTON
MOUNTING SCREWS
AND ANCHORS FOR
GD00Z-8-GC
POWER SUPPLY
AND BRACKET
1
PRODUCT DESCRIPTION
GD00Z-8-GC Overview
• A garage door opener remote command transceiver with built-in Z-Wave technology.
Z-Wave Information
• This is a Security enabled Z-Wave product and must be used with a Security enabled
• Allows remote operation of a garage door opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.
GD00Z-8-GC Summary of Operation
• GD00Z-8-GC connects to the garage door opener’s pushbutton wall console terminals.
• A wireless tilt sensor mounts on garage door and reports door’s position to
GD00Z-8-GC.
• GD00Z-8-GC responds to Z-Wave commands from Z-Wave controllers to open or close the garage door.
• A warning indicator light flashes and a beeper sounds for 5 seconds before the door begins to move.
• If the door does not completely open or close, a second open or close command can be sent after 30 seconds.
• If the door does not completely open or close after the second attempt, the
GD00Z-8-GC operation is suspended until a local garage door pushbutton is activated.
Z-Wave controller in order to fully utilize this product. As such, this device will not respond to Basic CC commands.
• ASSOCIATION: GD00Z-8-GC supports 1
Group with 1 Node. Group 1 must be assigned the Node ID of the controller to which unsolicited notifications from the GD00Z-8-GC will be sent. The Z-Wave controller should set this association automatically after inclusion.
• NOTIFICATION : GD00Z-8-GC supports the following notification types and events:
Access Control (Type 0x06) with events
0x44 (HW failure), 0x45 (UL Lockout), 0x46
(Obstruction), 0x49 (Loss of Tilt Sensor) and 0x4A (Sensor Low Battery). And additional type, Home Security (0x07) is also supported with event 0x03 (Tilt Sensor
Tampered).
• GD00Z-8-GC can be inter-operated in any
Z-Wave network with other Z-Wave devices from other manufacturers.
S2 Security
• Virtually impossible to hack.
• Z-Wave hub must also support S2 Security. If hub does not support S2, device will operate using standard security.
• Security 2 DSK label can be found on the bottom side of the product.
2
SAFETY NOTES
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO
ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system).
4
TILT SENSOR INSTALLATION AND BATTERY
1 To activate the tilt sensor, remove the battery protection pull strip.
2 Attach the mounting plate to the top panel of the door.
3
ARROWS ON PLATE &
SENSOR POINT UP
Snap the sensor onto the mounting plate.
5
PAIRING (INCLUDING) WITH THE SYSTEM
Note: Plug in the GD00Z-8-GC near your Z-Wave Controller for these steps
WALL
OUTLET
GD00Z-8-GC
POWER
SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
“UP”
ARROWS
POST ON
BOTTOM
The system will notify you when the battery is low, replace the battery with a type CR2032 coin cell.
1 To open the case, twist a small screwdriver in the case slot.
Use double sided tape or the two mounting screws supplied
(drill 1/16” pilot holes if required).
LOW BATTERY REPLACEMENT
2 Insert the battery into the transmitter.
PLUS SIDE UP !!!
CR2032
SLOT
1
TO INCLUDE THE GD00Z-8-GC
INTO YOUR CONTROLLER
Place your Z-Wave Controller into
Discovery or Include mode.
2 Press and release the link button on the GD00Z-8-GC.
3 Confirm that the GD00Z-8-GC was recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on including devices.
TO EXCLUDE THE GD00Z-8-GC
INTO YOUR CONTROLLER
1 Place your Z-Wave Controller into
Exclude mode.
2 Press and release the link button on the GD00Z-8-GC.
3 Confirm that the GD00Z-8-GC was excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on excluding devices.
6
GD00Z-8-GC MOUNTING
Tilt sensor mounted on the top panel of the door
The GD00Z-8-GC typically mounts on the ceiling near the opener and the power outlet
7
GD00Z-8-GC CONNECTIONS
3 Carefully join the power supply with the bracket
2 Plug the power cord into the power input jack on the GD00Z-8-GC
! WARNING !
1 Use the four screws and anchors to mount the GD00Z-8-GC above the opener
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
THE GD00Z-8-GC WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
THE GD00Z-8-GC CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
Secure bracket with screw
1A
The optional adjustable mounting bracket fits 3 ways on the GD00Z-8-GC
INDENT
INDENT
The bracket snaps onto indents on either side or on the end of the GD00Z-8-GC
1 Connect the GD00Z-8-GC connection wires to the push-button wall console terminals on the garage door opener. The terminals may be named "PWC", "WC", "PB", "PUSHBUTTON", or "RED and WHITE". Terminal names and locations vary by model.
4
Remove the screw from 120 VAC outlet faceplate. Plug in the adapter.
Secure the power adapter to the faceplate with the provided screw.
Feed the zip tie through the two holes in the bracket and secure.
DO NOT DISCONNECT ANY WIRES CURRENTLY
CONNECTED TO THE GARAGE DOOR OPENER.
3/16" HOLES
FOR ANCHORS
INDENT
Use the bolts and nuts supplied to attach the bracket to a secure structure
Either wire can connect to either terminal
USE WIRE TIES TO
SECURE EXCESS WIRING
AWAY FROM ALL MOVING
PARTS OF THE GARAGE
DOOR AND OPENER
2A
GARAGE
DOOR
OPENER
BE SURE THE GD00Z-8-GC IS
CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
9
OPERATION NOTES
1. The warning light will flash and the warning beeper will sound for five seconds before the door opener is activated. STAY CLEAR OF THE DOOR AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the
GD00Z-8-GC will allow user to try to operate the door one more time. If the second attempt fails, the GD00Z-8-GC will go into lock-out mode. See Note #3.
3. If the GD00Z-8-GC is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console.
4. Once the GD00Z-8-GC has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of
“bouncing” the garage door and possibly damaging the garage door opener.
PU
SH
BU
TT
ON
PU
SH
BU
TT
ON
10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
Unable to include in Z-Wave network.
The GD00Z-8-GC flashes and beeps when activated but the door does not move.
GD00Z-8-GC was not properly excluded from a previous Z-Wave network.
Obstruction blocking the door or incorrect wiring.
CORRECTIVE ACTION
1. Reset the GD00Z-8-GC by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset.
Reset should only be used in the case of a missing or inoperative primary controller.
2. Make sure that there are no obstacles preventing the door from moving.
3. Make sure that the GD00Z-8-GC connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the GD00Z-8-GC connection wires should be connected.
GD00Z-8-GC Specifications
Power Supply: Input: 120 VAC, 0.35 A
Output: 12 VDC, 1 A
Operating Temperature: -4°—122° F (-20°—50° C)
Audible Alarm: 45 db @ 10 feet
Strobe:
Z-Wave (908.4 MHz)
Mounting:
the ceiling, or bracket to the
opener’s hanging hardware
Tilt Sensor Specifications
Power Supply: Type CR2032 Coin Cell Battery
Operating Temperature: -4°—122° F (-20°—50° C)
Battery Life: 24 Months (typical)
Communications:
100 ft. line-of-sight to GD00Z-8-GC
Mounting to Garage Door: Double-sided tape or two
mounting screws
(Specifications subject to change without notice)
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL
LITHIUM BATTERY INFORMATION: THIS PRODUCT
CONTAINS A CR COIN CELL LITHIUM BATTERY
WHICH CONTAINS PERCHLORATE MATERIAL -
SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.
The GD00Z-8-GC flashes and beeps when activated but the door does not move.
The tilt sensor signal is not being received by the
GD00Z-8-GC.
1. Pair the tilt sensor with the GD00Z Garage
Door Controller.
a. Press and hold the pair button on the side of the GD00Z-8-GC main unit for about 7 seconds. It will emit a short chirp.
b. Release the button.
c. Rotate the tilt sensor 90 degrees to trigger a transmission. A short chirp should be heard.
d. If a short chirp is not heard, rotate the tilt sensor again.
2. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.
3. Make sure the battery pull tab has been removed from the tilt sensor.
4. Replace the battery in the tilt sensor.
8
SYSTEM OPERATION
1 Restore power to your
Garage door opener.
2 To synchronize the system, use the garage door opener's push-button to manually open and close the door.
3 Use the mobile app to control your garage door, view status and add your garage door control to automations and modes.
(For example, you can schedule your garage door to close nightly at sunset.)
4
The GD00Z-8-GC will beep and flash for five seconds before the door moves.
5 The GD00Z-8-GC will activate the door opener and open or close the garage door.
6
The touchscreen or mobile app will show the new status of the door after the door completes its cycle.
Copyright © 2020 Nortek Security & Control LLC
BEEP
BEEP
BEEP
FLASH
FLASH
FLASH
STAY CLEAR
OF THE DOOR!!!
STAY CLEAR
OF THE DOOR!!!
NORTEK SECURITY & CONTROL LIMITED WARRANTY
This Nortek Security & Control product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control or through Nortek Security & Control’s normal distribution channels. Nortek Security & Control does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Nortek Security & Control LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.
All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until the warranty expires. This Nortek Security & Control LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Nortek Security & Control Returns at 1-855-546-3351 for an RPA# and other important details.
REGULATORY NOTICES
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Les changements ou modifications non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
10025383 Rev-B
