Methven MNSRNK Minimalist MK2 Rail Shower Installation Sheet
Advertisement
Advertisement
Elbow Installation (if supplied):
•
•
Step 1
Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right.
Cut off the threaded nipple 13±2mm from the wall lining and apply thread seal tape to ensure a good seal.
•
•
Step 2
Screw the elbow onto the nipple ensuring that the o-ring is sufficiently compressed to create a watertight seal.
Ensure that the elbow is oriented vertically with the outlet oriented downwards.
13±2mm
26mm max
Care and Cleaning:
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth.
Periodically the filter washer should be removed from the end of the shower hose and cleaned.
ROUND RAIL
Installation Guide
Technical Specifications:
Inlet Connections:
All ½" BSP
* Regional specific regulations apply.
Please refer to your warranty statement at www.methven.com
Methven warrants this product against manufacturing defects and that it is suitable for use under the general operating conditions specified in this instruction sheet. However, regional regulations apply and may affect your warranty. Please refer to www.methven.com
or call customer service for full details.
New Zealand Australia UK
ISSUE
www.methven.com
IMPORTANT: Please read all of the instructions before installation.
General:
• This product must be installed in compliance with all relevant regional regulations.
• It is the responsibility of the installer to ensure a waterproof seal is achieved between the product and mounting surface. If in doubt about the quality of the seal, remove the product and reinstall using silicone to ensure a seal is achieved.
•
•
All pipe work must be thoroughly flushed prior to the installation of the hose.
After installation all connections must be checked for leaks.
• All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
• Where a Hand Shower and/or Overhead
Shower is fitted with a flow regulator the lower flow rate may not be suitable for the connection to some gravity fed Water Heaters, low pressure supply networks, Instantaneous
Water Heaters, Tempering Valves, Solar Water
Heaters & Thermostatic Mixing Valves. Check with the manufacturers of these products.
• Where showers incorporate flow controllers, care must be exercised during installation to ensure that the male connecting threads do not damage the flow controllers.
Wall Screw
Rail Tensioning Screw
Slider
Elbow
(if supplied)
Wall plug
Rail Bracket
Rail
Wall
Mounting
Plate
Grub Screw
•
Step 1
Mount the wall mounting plates in the desired position with the screws. Check the mounts are vertically aligned.
Step 2
•
• Set location of the upper rail bracket on the rail and loosely tighten the tensioning screw.
Align the rail brackets to the wall mounting plates and push into place.
• Remove the rail and tighten the tensioning screw firmly.
• Replace the rail onto the wall mounting plates and tighten the upper and lower grub screws.
•
Step 3
To adjust slider position, rotate the slider handle to unlock and lock the slider as shown.
Lock
Grub Screw
Grub Screw
FLOOR
Unlock
Care and Cleaning:
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth. Thoroughly rinse with clean water and wipe dry. Limescale deposits on the product can be avoided by wiping dry immediately oafter use.
Periodically the filter washer should be removed from the end of the shower hose and cleaned.
MINIMALIST MK2
WALL OUTLET BRACKET
Installation Guide
Technical Specifications:
Operating Pressure:
Min: 150kPa/1.5bar - 500kPa/5bar
Max: 1000kPa/10bar*
Optimum: 150kPa/1.5bar - 500kPa/5bar
Operating Temperature:
Hot: Max 80°C*
Cold: Min 5°C
Inlet Connections:
All ½" BSP
* Regional specific regulations apply.
Please refer to your warranty statement at www.methven.com
Methven warrants this product against manufacturing defects and that it is suitable for use under the general operating conditions specified in this instruction sheet. However, regional regulations apply and may affect your warranty. Please refer to www.methven.com
or call customer service for full details.
New Zealand
0800 804 222
IS 1925
Australia
13 14 16
UK
0800 195 1602
ISSUE A
www.methven.com
•
•
IMPORTANT: Please read all of the instructions before installation.
General:
• Methven recommends this product is installed by a licensed plumber in compliance with all relevant regional regulations.
After installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per regional regulations.
• It is the responsibility of the installer to ensure a waterproof seal is achieved between the product and mounting surface. If in doubt about the quality of the seal, remove the product and reinstall using silicone to ensure a seal is achieved.
•
•
Where a Hand Shower and/or Overhead Shower is fitted with a flow regulator the lower flow rate may not be suitable for the connection to some gravity fed Water Heaters, low pressure supply networks, Instantaneous Water Heaters, Tempering Valves, Solar Water Heaters & Thermostatic
Mixing Valves. Check with the manufacturers of these products.
Where showers incorporate flow controllers, care must be exercised during installation to ensure that the male connecting threads do not damage the flow controllers.
O-ring
Faceplate
IMPORTANT: Before you begin, turn off the water supply.
•
•
Step 1
Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right
Cut off the threaded nipple 15±2mm from the wall lining and apply thread seal tape to ensure a good seal.
15±2mm
26mm max
•
•
Step 2
Insert o-ring into the groove in the trim ring and slide the trim ring and faceplate over the nipple.
Secure faceplate in place by screwing the inlet connector onto the nipple.
Outlet Bracket
•
•
Step 3
Connect hose to outlet bracket and handset.
Ensure swivelling cone is connected to the handset.
Filter Washer
Non-Swivelling Cone
Handset
Flat Washer
Swivelling
Cone

Public link updated
The public link to your chat has been updated.
Advertisement