TheSmartDVR.com
JPEG2000 + H264 USER MANUAL
Models covered
DSD154 – 4 Channel DVR
DSD158 – 8 Channel DVR
DSD160 – 16 Channel DVR
Version 3.0
1.0
Quality & Value
The SmartDVR.com
INSTALLATION & SAFEGUARDS
INSTALLATION & SAFEGUARDS
All the safety and operating instructions should be read before the unit is operated.
Environment Condition for Installation
-
To prevent electric shock or other hazard, do not expose this unit to rain, moisture or dust.
This unit should be located in an area with low humidity and a low dust level.
Place this unit in a well-ventilated place and do not place heat-generating objects on this unit.
This unit should not be located in an area where it is likely to be subjected to vibration.
Before You Start
-
Ensure the power switch is in the OFF position prior to starting.
Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.
Installation should be performed by qualified service personnel only.
This unit should be operated only from the type of power source indicated on the manufacturer’
s label
and with the power supply included with the unit.
Notice
-
Before initial configuration or operation you must first set the TIME/DATE, followed by setting the unit to
the FACTORY DEFAULT settings, lastly clearing the HDD. Please follow these steps in order.
-
Pull the unit out of record mode prior to cutting off power to the unit. Do this by entering the setup
menu, followed by switching the unit off. Powering off the unit while writing to the disks can cause
critical malfunctions. (Ex: Recording Error, Playback Error, System Error).
-
When you set the record type, you have to set the Record Configuration and also Schedule Setup. This
unit records as per the Record type & Schedule setup.
-
The [REC] button on the front panel is for emergency record using highest image quality.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of this
equipment that there are dangerous voltages within the enclosure, which may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (Servicing) instructions in the literature accompanying the appliance.
2
Quality & Value
The SmartDVR.com
Chap.1
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Features & Package Contents
1-1.
Features
1-2.
Package Contents
Chap. 2
Function of Each Button
2-1.
2-2.
Chap. 3
Front
Rear
Installation
3-1.
Installation Configuration
3-2.
Detailed Installation
1)
Rack Mount
2)
HDD(Hard Disk Drive)
3)
Camera
4)
Monitor
5)
Power
6)
Spot, Video Printer
7)
Chap. 4
Other External Device
Operation
5
5
6
-----------------------------------------------------------------------------------------------------------------------------
7
-----------------------------------------------------------------------------------------------------------------------------
9
7
10
-----------------------------------------------------------------------------------------------------------------------------
10
-----------------------------------------------------------------------------------------------------------------------------
11
-----------------------------------------------------------------------------------------------------------------------------
12
-----------------------------------------------------------------------------------------------------------------------------
12
-----------------------------------------------------------------------------------------------------------------------------
13
-----------------------------------------------------------------------------------------------------------------------------
14
14
11
11
12
13
14
4-0.
Start-up DVR
4-1.
4-2.
System Log-in
Factory Default
4-3.
Display Configuration
-----------------------------------------------------------------------------------------------------------------------------
Live View Setup
Full / Multiple View
-----------------------------------------------------------------------------------------------------------------------------
15
2)
View in Sequence
16
3)
PIP View
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
16
-----------------------------------------------------------------------------------------------------------------------------
17
-----------------------------------------------------------------------------------------------------------------------------
18
4-4.
1)
4) Freeze View
5) Zoom View
4-5. Record
4-6. Playback
4-7.
Search
4-8.
PTZ Camera Operation
4-9.
Data Back-Up
4.10
Audio Operation
-----------------------------------------------------------------------------------------------------------------------------
4.11
Mouse Operation
---------------------------------------------
3
14
15
15
16
16
17
18
19
19
20
Quality & Value
The SmartDVR.com
Chap.5
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Set Up
5-1.
Entering the Menu
5-2.
Display Setup
1)
Screen Display
2) Monitor Setup
5-3.
1.
Configuration
HDD Management
2.
Time/Date Setup
3.
Camera Setup
4.
Interval Setup
5.
Alarm Setup
6.
Event Popup
7.
Buzzer Setup
8.
Password Setup
9.
5-4.
Record Setup
1.
Record Configuration
2.
Schedule Setup
3.
5-5.
5-6.
1.
Holiday Setup
Back-Up
External Device
TCP/IP Setup
25
-----------------------------------------------------------------------------------------------------------------------------
26
-----------------------------------------------------------------------------------------------------------------------------
28
-----------------------------------------------------------------------------------------------------------------------------
30
35
38
40
Spot Monitor Setup
5.
Audio Setup
IRS (Integrated Remote Station)
CHAP. 8
Programmer Reference
CHAP. 9
Specifications
CHAP10
Appendix
-------------------------------------------------------------------------------------------------------------------------------------------------------
Hand Remote Controls
Channel Record Timetable
32
33
34
35
38
41
41
42
-----------------------------------------------------------------------------------------------------------------------------
43
-----------------------------------------------------------------------------------------------------------------------------
63
-----------------------------------------------------------------------------------------------------------------------------
66
-------------------
4
31
-----------------------------------------------------------------------------------------------------------------------------
4.
CHAP. 7
31
33
---------------------------------------------------------------
Network Setup
30
-----------------------------------------------------------------------------------------------------------------------------
Pan Tilt Zoom Setup
CHAP. 6
30
32
3.
Language Setup
28
-----------------------------------------------------------------------------------------------------------------------------
RS-232C Setup
5-8.
26
31
2.
FACTORY Default
25
-----------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------
5-7.
25
-----------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
System Information
24
24
46
65
68
Contents
Quality & Value
The SmartDVR.com
CHAP. 1 Features & Package Contents
1-1. Features
Live View
Real time display per camera
Auto Sequence
PIP (Picture in picture)
Event Popup
Digital Zoom
Display Freeze
Simple Playback mode
Simple PTZ camera control
Record
Variable Record resolution (For higher picture quality or higher recording speed)
Efficient Image Quality setup in 5 steps
Schedule Record / Holiday Record
Event Record (Alarm / Motion)
Emergency Record
Network
View Live and Playback images across IP network
Copy images across the network
Network Video Server
Playback
Search & Playback by Date/Time, Event and Camera
Outstanding picture quality by JPEG 2000 compression algorithm (No mosaic effect)
Suitable for recording not only images but also text
Forward Playback Speeds (X1/16, X1/8, X1/4, X1/2, X2, X4, X16, X32, X64)
Backward Playback Speeds (X1/16, X1/8, X1/4, X1/2, X2, X4, X16, X32, X64)
Easy and convenient search by Jog Shuttle & Remote Controller
Data Back-Up
Simple Back-Up using built-in DVD Writer (Back-up DVD Player included in the package)
Network Back-Up using Remote Viewer program(Remote Viewer included in the package)
Supports larger capacity of HDD (500GB or larger)
Others
Multi-Language (English, Spanish, German, French, Italian, Japanese & Chinese)
VGA support both TFT LCD monitor and CRT monitor (option)
Lock the system by Password
JOG / SHUTTLE
PAL/NTSC Auto detection
Control the unit by using Remote Controller (Normal, Single, Universal)
Audio recording: IN – 4 channels, OUT – 1 channel (mono)
5
CHAP. 1 Features & Package
Contents
Quality & Value
The SmartDVR.com
1-2. Package Contents
1. DVR Main Unit
2. Remote Controller
3. Power Cable
4. Power Adapter
7. Battery for remote
6. Software CD
5. User’
s Manual
8. Bolts & Foam Mount washers
Package Contents
9. Mouse
Description
1. DVR Main Unit
STAND-ALONE DIGITAL VIDEO RECORDER
2. Remote Controller
DVR control
3. Power Cable
AC power supply to adapters for 12 V DC power
4. Power Adapter
12 V DC power supply to DVR main board
5. User’
s Manual
User’
s Manual
6. Software CD
Remote Viewer Software & Back up DVD player
7. Battery
Battery for remote controller
8. Bolts & Foam
Mount Washers
For attaching Hard Disk Drive into DVR
9. Mouse
PS/2 Mouse
6
CHAP. 2 Function of Each Button
Quality & Value
The SmartDVR.com
1
4
9/20
2-1 FRONT
10
11/21
23
33
5
6
15/18
14/17
16/19
13
7
12
22
Name
1. LEDs
2.1 USB
24
2.1 / 2.2
Function
Shows status of operation
Used for backup via upper USB port
2.2 USB
Used to upgrade Firmware only via lower USB port
3 IR
IR receiver
4.1 Camera
4.1. Pressing these buttons will display a full screen image of that camera
selection
4.2 PTZ camera control
5. SHIFT
6. E-REC
4.2. Control PTZ camera (Each button is assigned for each PTZ command)
•ON: LIGHT ON
•SET: SET PRESET
•OFF : LIGHT OFF
•CLEAR : CLEAR PRESET
•OPEN : IRIS OPEN
•GOTO : GOTO PRESET
•CLOSE: IRIS CLOSE
•AUTO : AUTO SCAN
•NEAR : FOCUS NEAR
•F1 : USER 1
•FAR : FOCUS FAR
•F2 : USER 2
•WIDE : ZOOM IN
•F3 : USER 3
•TELE : ZOOM OUT
•F4 : USER 4
THIS KEY IS PRESSED TO SELECT ADDITIONAL FUNCTIONS ON A KEY
Emergency Record at continuous, 60ips, SUPER FINE size
(Press & hold for 3 seconds to return to Schedule Record)
7. PLAY
Playback of recorded data on HDD
7
Quality & Value
The SmartDVR.com
8. SHIFT &
Search recorded data on HDD
PLAY
9. MENU
Set up for SYSTEM MENU or Use to exit the menu
PRESS MENU BUTTON BEFORE POWERING OFF UNIT
10. ENTER
Selects each menu option
11. NEXT
Move to next step
12.
Navigate in the menu
13. + -
Reduce or increase the option value in the menu
(USE SHIFT KEY)
14. PTZ
15. SEQ
On/Off for PAN/TILT/ZOOM control mode
Press this button first to control PTZ camera connected to DVR unit via
RS-485
Auto sequencing in full screen mode
16. PIP
Picture in Picture mode
17. AUDIO
Select audio channel
18. ZOOM
Zoom control
19. FRZ
Freezes an image
20. K.LOCK
Lock key function (to unlock press Shift & K Lock for 3 seconds)
21. MODE
Switches from full screen display to 9 split screen
22. Q.PLAY
QUICK PLAY – Play images recorded 2 minutes ago in forward
direction (only if recording in continuous mode)
23. JOG SHUTTLE
Pressing Jog Shuttle button (Ready for use Jog/Shuttle): In playback mode,
pressing J. SHUTTLE button freezes images.
RUN LED on: While you operate Jog or Shuttle
ACTIVE LED on: When J. SHUTTLE button is pressed
SEARCH FACILITY : Press J. Shuttle button, and images in playback pause,
and Jog and Shuttle makes it very easy and convenient to search forward or
backward, fast and slow, as user wants. Note that Jog Shuttle can only be
activated when ACTIVE LED is ON.
24. DVD-RW
Data Back-up using built-in DVD writer
8
Quality & Value
CHAP. 2 Function of Each Button
The SmartDVR.com
2
2-2 REAR
5
7
1
11
12
3
1
4
6
8
9
Name
Functions
RS485
Connection with PTZ Camera or other external device using RS 485 interface
(Pin 1: D- / Pin 2: D+)
RELAY Output
Relay out terminal Pin 3 Common, Pin 4 NC, Pin 5 NO
SENSOR Input
Sensor input terminal Pin 8 – 15 Alarms 08 – 01
2
VGA
3
ETHERNET
4
RS-232C
5
CAMERA Input
6
LOOP Output
7
MONITOR
Output
8
SPOT
9
DC Power
Pins 6-7 Grounds
Connection to VGA Monitor (CRT type or TFT LCD monitor)
Connection to ETHERNET device
Connection to external device as PC using RS-232C to control the
DVR. NOTE: This facility is not supported.
Connection with camera
Camera loop out
Connection with Composite Video Monitor
Connection with additional Composite Video Monitor
DC power input (DC12V, 6.67A adapter)
Power ON/OFF.
10
POWER
SWITCH
11
12
NOTE: To avoid deletion of HDD data, make sure you press MENU
button and enter into menu setup before powering down. This safely
takes unit out of record mode.
Audio Input
Microphone input (4 channels)
Audio Output
Speaker Output (1 channel)
Mouse
PS/2 Mouse controls all functions of DVR
9
10
Quality & Value
The SmartDVR.com
CHAP.3 Installation
3-1. Installation Configuration
10
CHAP. 3 Installation
Quality & Value
The SmartDVR.com
3-2. Detailed Installation
1)
Rack mount
1.
Remove 4 bolts on each side to install rack mount brackets
2.
Attach rack mount bracket
3.
Attach DVR brackets to 19”rack.
Hard Drive fitting points
2)
HDD
I/O BOARD
I/O BOARD
MAIN
MAIN BOARD
MAIN
MAIN BOARD BOA
BOA
Screw hole
HDD1
(MASTER1)
HDD2
(MASTER2)
CD Recorder
(MASTER)
x x
x x
x x
x x
x x
x x
1. Connect Main Board and HDD1 using IDE cable and HDD power cable.
2. When you use just 1 HDD, install the HDD onto HDD1 location.
3. When you use 2 HDDs, install the first HDD onto HDD1 location and then install the second HDD
onto HDD2 location in order.
4. Stick the HDD absorber (included in package) on the bottom of case and then install the HDD
on top of them by using the bolts (included in package).
5. Screws must be inserted from outside of the case bottom.
Special Note: This DVR uses serial (SATA Hard Drives). These are regarded as Master only drives.
11
CHAP. 3 Installation
Quality & Value
The SmartDVR.com
3) Camera
Connect cameras to the camera input on rear panel of DVR marked CAMERA IN.
4) Monitor
Connect the video output marked MONITOR to Video In of Main monitor.
5) Power
Connect one 12V DC 6.67A adaptor to
the DC12V input connector on rear of
unit.
NOTE: Before you turn on power switch,
ensure that power adaptor, cameras and
monitor are connected properly.
ALSO TO AVOID DELETION OF HDD
DATA, ENSURE YOU PRESS MENU
AND ENTER BEFORE POWERING
DOWN. THIS TAKES UNIT OUT OF
RECORD MODE.
12
CHAP. 3 Installation
Quality & Value
The SmartDVR.com
6) SPOT, VIDEO PRINTER
MIC
AUDI O
PC
VG A
I N1
2
1
4
3
5
6
8
7
1 0
9
11
IN 2
12
13
IN3
I N4
ET HERNET
14
O UT
R S-232 C
15
PC
PTZ
C AMER A
SPEAK ER
PAN/T ILT
CAMERA
VGA
M ON ITOR
SIRE N
SENSOR
SENSOR
RS-232C : Control DVR through RS-232C port by using PC (N.B Not supported.)
RS-485 : Control external device like PTZ Camera
RELAY Output : Relay Output (Pin 3 ~5 at Terminal Block).
SENSOR Input : SENSOR Input (Alarm connection)
ETHERNET: Connection to LAN, WAN, Internet.
VGA: Connection to VGA monitor(CRT,TFT LCD).
Select VGA in DISPLAY SETUP menu before connection to VGA monitor
Resolution set by manufacturer is 800x600 60Hz. This can be altered by
entering Monitor Setup/ VGA Setup / VGA resolution
Use VGA option board for both CRT type PC monitor or TFT LCD monitor.
AUDIO INPUT: Microphone Input (IN1~IN4)
AUDIO OUTPUT: Speaker Output (OUT)
13
Quality & Value
The SmartDVR.com
CHAP.4 Operation
4-0. Starting up system
Before turning on the DVR be sure that everything is firmly connected. Turn on the DVR and
go the Menu using the relevant Login Password and you will then see the System Setup
Screen. You may proceed by referring to the related chapters describing the various
functions.
4-1. System Log-In
1)
To enter into the setup menu, press the [MENU] button.
2)
Enter password with channel number button from No.1 to No.10 on
the front of the DVR unit. (Maximum of 8 digits are available)
3)
After inputting the password, press the [ENTER] button.
ENTER PASSWORD : _ _ _ _ _ _ _ _
INPUT YOUR OWN PASSWORD
TO EXIT, PRESS [MENU]
1
2
3
4
5
6
7
8
9
10
Administrator:
If the password entered matches previously set password, “LOGIN
ADMIN”message appears and you
can enter into SYSTEM SETUP. If the password entered does not
match previously set password, the DVR unit goes back to live
display mode.
Factory default password is blank. For log-in, just press [MENU] button, followed by the [ENTER] button.
-Factory default password
ADMIN: (Blank)
MANAGER: ‘1 ’
USER 1~USER 8: ‘2 ’~ ’9 ’
We recommend configuring a unique password as per the procedure in SYSTEM MENU - CONFIGURATION PASSWORD SETUP.
For security reasons, be sure to make note of your own password.
4-2. Factory Default
Before initial configuring or operation you must first set the Time/Date, followed by setting the unit to the FACTORY
DEFAULT settings, lastly clearing the HDD. Please follow these steps in order. Improper operation may result if
this action is not taken. Starting without FACTORY DEFAULT & HDD clear will cause malfunctions.
1. HDD CLEAR (page 22)
DISPLAY SETUP
CONFIGURATION
RECORD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE
2.. FACTORY DEFAULT (page 31)
DISPLAY SETUP
CONFIGURATION
RECORD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE
HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
EVENT POPUP SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM INFORMATION
14
Quality & Value
The SmartDVR.com
4-3. Display Configuration
4-4. Live View Setup
1) Full / Multiple View
Switch to multi-screen displays by pressing [MODE]. For full image display, just press the channel button you want or
keep pressing [MODE] button. When you playback images that are recorded in 360x240 (360x288) or 360x120
(360x144) resolution, only 1, 4 and 9 way split screens are available.
Full Screen
FULL
SCREEN
(
360x240
360x120
)
<During Playback>
¼ Full Screen
15
Quality & Value
The SmartDVR.com
2) View In Sequence
Press [SEQ] button. It automatically displays full screen images in sequence. To stop the sequence press the
[SEQ] button.
CH08
3) Picture in Picture (PIP View)
When it is in full screen display mode, you can see another camera in a small
window by pressing [PIP]. This camera window rotates in sequence to next
camera and you can set the rotating time interval as per the procedure in
SYSTEM MENU-CONFIGURATION- INTERVAL SETUP.
CAM-01
2
4) Freeze View
Full display mode:
If you press the [FRZ] button, the FRZ icon will be activated on screen and the “F”character will
be shown beside camera title, and the live image will be frozen.
Split display mode: If you press the [FRZ] button, the FRZ icon will be activated on screen . Then press the
channel button you want to freeze.
To release frozen image, press channel number of frozen image again and press [FRZ]
button to exit FRZ mode.
5) Zoom View
In full screen, press the [ZOOM] button and move the Selection Frame using Jog Shuttle or direction keys to the area
which you want to enlarge. Then press the [ENTER] button for 2-times enlarged picture. To exit Zoom mode, just
press [ZOOM] button again.
Horizontal Movement: Jog Shuttle
Vertical Movement:
Hold [UP or DOWN] button and turn Jog Shuttle
16
Quality & Value
The SmartDVR.com
4-5. Record
The recording mode set before delivery by manufacturer (Default recording mode) is Schedule Recording. In this
default recording mode, it records 24 hours/day continuously during weekdays and the weekend.
If you press the [E-REC] button whilst you are in live view mode, the record type is changed to Emergency Record
mode.
EMERGENCY RECORD: at full resolution/best quality
Record type : CONTINUOUS, SUPER FINE quality,
60 (50) ips at 720X240 (720x288)
Emergency Record [RED]
Schedule Record [GREEN]
SCHEDULE RECORD:
Record and stop as set (time interval and record type) in
RECORD-SCHEDULE SETUP menu.
Stop Record [WHITE]
STOP RECORD:
Recording stopped as set in
RECORD-SCHEDULE SETUP menu.
On the screen
-Emergency Record
: Red Record Icon LED is lit
- Schedule Record
: Green Record Icon LED is lit
- Record Stop
: White Icon Record LED is off
- Motion Record, Alarm Record, Alarm+Motion Record
: Record standby LED blinks
: Record LED is lit
While in Emergency Record mode, press [PLAY], [MENU],
or [SEARCH] button to exit from Emergency Recording mode
and return to Schedule Record mode or press E-REC button
for three seconds.
Further details, refer to the SYSTEM MENU – RECORD SETUP.
This DVR unit does not record in the following conditions:
While entered in the menu
No camera connected
HDD is full and Overwriting is off in the Record Setup menu.
4-6. Playback
In record mode or stop mode, press [PLAY] button to play the recorded data in 1x speed. Press [LEFT] for backward playback
or press [RIGHT] button for forward playback. Use Jog Shuttle to pause and control playback speed. To stop playback, press
the [PLAY] button again.
Using Jog/Shuttle
When the [ACTIVE] LED is on the [JOG SHUTTLE] is ready for use. The [RUN]] LED will blink whenever you operate the Jog
Shuttle. For forward playback, turn the Shuttle right and turn Shuttle left for backward playback. Turn the inner Jog using your
index figure to see picture by picture in forward or backward direction. Operation of Shuttle is as follows.
If you want to keep
the playback speed
you have selected
using Shuttle, just
hold the shuttle at that
location for a few
seconds, and
playback in speed you
selected continues
until you rotate Shuttle
again.
1/4 x : 4 times slower than normal playback speed
1/2 x : 2 times slower than normal playback speed
1 x : Normal playback speed
2 x : 2 times faster than normal playback speed
4 x : 4 times faster than normal playback speed
16 x : 16 times faster than normal playback speed
64 x : 64 times faster than normal playback speed
17
Quality & Value
The SmartDVR.com
4-7. Search
Press [PLAY] & [SHIFT] buttons, and 3 different methods for searching recorded data are available as
shown in following SEARCH window. For selecting searching method, use direction key or Jog Shuttle.
After selecting each search method, press [ENTER] button for playback. To exit press [MENU].
1) SEARCH BAR
Search by percentage of total recorded data, using the arrow keys or the jog shuttle. It starts from
image corresponding to set % of data on the search bar.
2) TIME/DATE
Search by time & date. Playback starts from the time & date selected.
3) EVENT LIST
Search by event list (Motion, Alarm, Video Loss).
SEARCH page
SEARCH BAR page
EVENT LIST page
TIME/DATE page
4-8. PAN/TILT/ZOOM Camera Operation
Press [PTZ] button first for PTZ control mode. Numeric buttons from 1 to 16 and direction buttons are assigned for
each PTZ command, and user can control PTZ camera connected to DVR unit by pressing any one of those 20
buttons, one after the other, as needed, and it is similar to controlling by a separate PTZ controller.
18
Quality & Value
The SmartDVR.com
Button
1/ON
2/OFF
3/OPEN
4/CLOSE
5/NEAR
6/FAR
7/WIDE
8/TELE
9/SET
PTZ command
LIGHT ON
LIGHT OFF
IRIS OPEN
IRIS CLOSE
FOCUS NEAR
FOCUS FAR
ZOOM OUT
ZOOM IN
PRESET SET
Button
10/CLEAR
11/GOTO
12/AUTO
13/F1 ~ 16/F4
UP BUTTON
DOWN BUTTON
LEFT BUTTON
RIGHT BUTTON
PTZ command
PRESET CLEAR
PRESET GOTO
AUTO SCAN
FUNCTION
TILT UP
TILT DOWN
PAN LEFT
PAN RIGHT
4-9. Data Back-Up
Enter into SYSTEM MENU-BACKUP-CDR SETUP.
1) Insert empty CD-R or DVD-R media into DVD writer and select the start time & date from which you want to
back up. The START & END time / date in HDD sub-menu only shows start and end of recording. This is not
selectable and editable.
(700MB on CD-R sub-menu represents size of CD-R media and 4480MB on DVD-R media inserted.)
2) To set start time of back-up and back-up data size, press the [ENTER] button first on [START] or [SIZE] submenu and adjust using [+] or [-] button and move using [LEFT] and [RIGHT] button for next change. After setting
the time & date and back-up data size, press the [ENTER] button again to exit.
End of back-up time will be calculated automatically as per start time & date and the back-up data size you set.
User can select the back-up data size (size of back-up data from start of back-up) on [SIZE] item but END of
back-up time is automatically determined by DVR system.
3) Press [ENTER] button on BURN sub-menu. DVR system starts burning CD or DVD.
4) When burning is completed, CD-R or DVD-R media will eject automatically. If you wish to continue backup
of more data, the next CD/DVD back-up, set the start time of the next backup as the end time of previous
back-up. If you need another backup, repeat the above procedure. To stop backup, press the [MENU] button.
During the backup burning process it’
s impossible to cancel burning.
User can verify the back-up media on a PC. On insertion the media will auto run.
CHAP. 5 Set Up
NOTE: SIZE = 4480MB WITH DVD-R MEDIA
4.10. Audio Operation
Go into External Device menu and select audio setup. Set channels required. Note that Audio only works in
DUPLEX mode and not in TRIPLEX mode. Also changing frame rate or using motion detect may affect
Audio playback. If in doubt set factory defaults – audio will definitely work. Press [AUDIO] button to select
audio channel … . CH1, CH2, CH3, CH4 or SILENCE in sequence. Sound of the selected audio channel can
be heard in LIVE mode display. Recorded sound is heard in Playback mode.
19
Quality & Value
The SmartDVR.com
4-11. Mouse Operation
1) Basic Operation
There are 11 keys that work by Mouse.
These include LEFT (3) Click once, double click & click hold
RIGHT (3) Click once, double click & click hold
WHEEL (5) Upper, lower, click once, double click & click hold
2) The Mouse cursor is not present
The following are reasons why the mouse cursor may not be displayed
Double clicking the LEFT button : The assigned channel is sequencing to FULL Screen
and double clicking Left button it reverts to previous split screen. If user selects FREEZE,
the assigned channel freezes.
Double clicking the RIGHT button : The MOUSE ICON will be on and depending on the
place of Mouse, it shows Width,Length and BOT.
Click hold WHEEL button : Deletes MOUSE ICON
Click Hold LEFT button : In ZOOM mode, holding this button will change the icon.
If User moves the MOUSE, ZOOM area also moves.
3) Working Status in SETUP MENU
- LEFT button click once : ENTER
- LEFT button double click : NEXT
- LEFT button click hold : MINUS
- WHEEL button click once : MODE (Schedule Recording, MASK SETUP)
- WHEEL button double click : LEFT (For deleting password)
- WHEEL button click hold : None
- WHEEL button upper : PLUS
- WHEEL button lower : MINUS
- RIGHT button click once : MENU
- RIGHT button double click : PLAY
- RIGHT button click hold : PLUS
Use the Left button to select Menu, and the Right button to exit Menu.
Move mouse up and down, moving left selects menu items.
WHEEL : for plus/minus
Left button : to press enter
Wheel button double click : for password deletes at Login.
20
Quality & Value
The SmartDVR.com
4) Working Status of LIVE MOUSE ICON
To work command in LIVE MOUSE ICON, user clickS Left button once.
In case ICON is divided, upper part of button : Mouse Left button click once
Lower part of button : Mouse Right button click once
Following is the assigned KEY by each ICON.
ICON
Left Click
Right
Click
ICON
MENU
Left Click
Right Click
NEXT
ENTER
PLUS
MINUS
MODE
REC
STOP
PLAY
SEARCH
PTZ
ZOOM
FRZ
PIP
SEQ
AUDIO
KLOCK
QPLAY
5) Working Status of PLAY MOUSE ICON
Mouse works the same as the above LIVE ICON.
Place mouse on
ICON and by Wheel Up/Down button, PLAY SPEED can be controlled.
Pause mode, place mouse on
can be controlled.
ICON and by Wheel Up/Down, STEP PLAY
21
Quality & Value
The SmartDVR.com
Following is the assigned KEY by each ICON.
ICON
Left Click
Right
Click
STOP
BACKWARD
WHEEL
ICON
Step play
Left Click
Right
Click
SLOW
BACKWARD
FAST
BACKWARD
PLAY
FAST
FORWARD
SLOW
FORWARD
STOP PLAY
REC
WHEEL
Step play
PLAYBACK
SPEED
PAUSE
STOP
ZOOM
MENU
AUDIO
MODE
6) Working Status of PTZ MOUSE ICON
Mouse works
the same as the LIVE ICON.
Place Mouse on
ICON , and using Wheel Up/Down, you can change value PRESET,TOUR,
GOTO and etc.
For other ICONs, user can change channel by Wheel Up/Down.
Following is the assigned KEY on each ICON.
ICON
Left Click
Right
Click
WHEEL
ICON
LEFTUP
Left Click
Right
Click
UP
RIGHTUP
LEFT
Change
Channel
ENTER
Change
Channel
RIGHT
LEFTDOWN
DOWN
RIGHTDOWN
ZOOM IN
OUT
GOTO
PRESET
PLUS
MINUS
AUTO
SCAN
MENU
NEXT
FOCUS
NEAR
SET PRESET
CLEAR
PRESET
PTZ
MENU/EXIT
WHEEL
FAR
FOCUS
FAR/NEAR
Change
Channel
22
ZOOM
IN/OUT
Change
Channel
PRESET
NUM +/Change
Channel
Change
Command
Quality & Value
The SmartDVR.com
7) Working Status of SPLIT MOUSE ICON.
To change assigned screen division, click left button of mouse once.
Please note that specific division cannot be supported such as QUAD record/playback.
and according to DVR channel, screen division can be different.
1
4
8
6
8) Working Status of NUMBER MOUSE ICON.
User can use it for KLOCK or LOGIN and change PASSWORD.
1
2
3
4
5
6
7
8
9
10
23
9
Quality & Value
The SmartDVR.com
CHAP. 5 Set Up
5-1. Entering into the Menu
Enter into SYSTEM MENU by pressing [MENU] button.
BUTTON
FUNCTION
MENU
Enter into SYSTEM MENU, Move to previous menu, ESC
ENTER
Selection key, Move to sub-menu, change status (ON or OFF)
NEXT
UP
DOWN
Move to next page
Move Up
Move down
LEFT
Move left
RIGHT
Move right
MINUS [-]
Decrease the option value
[SHIFT] + [
PLUS [+]
Increase the option value
[SHIFT] + [ ] key
Jog
Shuttle
] key
Jog Left turning: Move backward to next image / Decrease value
Jog Right turning: Move forward to next image / Increase value
Shuttle left turning: Reduce playback speed / Decrease value
Shuttle right turning: Increase playback speed / Increase value
CD-R/DVD-R/W SETUP
USB SETUP
HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
EVENT POPUP SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM INFORMATION
TCP/IP SETUP
RS-232C SETUP
PAN/TILT SETUP
SPOT MONITOR SETUP
AUDIO SETUP
AUDIO VOLUME SETUP
REMOCON SETUP
SYSTEM MENU
24
Quality & Value
The SmartDVR.com
5-2. DISPLAY SETUP
Setting up parameters for monitor and display on screen.
Enter into SYSTEM MENU-DISPLAY SETUP.
1) SCREEN DISPLAY
Setting up the screen display in LIVE mode and PLAYBACK mode.
Select the sub-menu, that you would
like to set using direction buttons and
then change ON/OFF with [ENTER]
button.
1. TIME/DATE: Display time & date
2. DVR STATUS: Display system setting status
3. ICON DISPLAY: Display function setting status
4. REC/PLAY BAR: Display record / playback status
5. CAMERA TITLE: Display camera title
2) MONITOR SETUP
VGA SETUP: The VGA card enables you to connect a TFT LCD monitor or CRT type PC monitor to this unit.
You will have to select one of the resolution settings below using the [+] [-] button. After setting the
option below, press [ENTER] button then the DVR unit will set VGA mode automatically.
1280x1024 /60Hz or 1024x768 / 60Hz
1280x1024 /75Hz or 1024x768 / 75Hz
or 800x600 / 60Hz
or 800x600 / 75Hz
or 640x480 / 60Hz
or 640x480 / 75Hz
The resolution reflects pixels per inch. The higher the pixel rate the better the quality.
Best quality is therefore 12804x1024 / 75Hz but must match TFT LCD or CRT PC monitor
COLOUR BAR TEST: Necessary to adjust colour tone of monitor. (Not available with
3
VGA option)
NOTICE: When this DVR unit is operated for the first time, it will take a few seconds to boot up for initialisation of VGA
mode.
4
25
Quality & Value
The SmartDVR.com
5-3. CONFIGURATION
Various system parameters can be set in the CONFIGURATION menu.
Enter the SYSTEM MENU-CONFIGURATION and press the [ENTER] button.
HDD SETUP
HDD INFORMATION
HDD CHANGE SETUP
1) HDD MANAGEMENT
Enter SYSTEM MENU-CONFIGURATION-HDD MANAGEMENT and press the [ENTER] button.
(1) HDD SETUP
This page includes information about start and end of recording, location of recorded data, or location of last
playback on HDD. In addition, users can delete all the data on HDD.
HDD SETUP
On the [HDD CLEAR] sub-menu, press the [ENTER]
button to delete all image data on HDD.
STATUS
HDD
DATE/TIME
---------------------------------------------------------------------BEGIN
MASTER-1
2005/04/08
MASTER-1
12:12:05
RECORD MASTER-1
2005/04/09
MASTER-1
15:09:58
PLAY
MASTER-1
2005/04/08
MASTER-1
19:44:31
HDD STATUS
HDD CLEAR
The system will ask you the password for verification. After
you clear all data on the HDD, the status of HDD CLEAR
changes from IN USE to EMPTY.
When you clear HDD, the event list is deleted, too.
NORMAL
IN USE
HDD CLEAR [ENTER], EXIT [MENU]
If you selected OVERWRITE in Record Setup, the HDD STATUS above will display OVERWRITE.
HDD INFORMATION
(2) HDD INFORMATION
This menu will show the physical state of the HDD in the DVR.
[MASTER-1]
MODEL
SPEED
SIZE
START
END
[MASTER-2]
MODEL
SPEED
SIZE
START
END
:
:
:
:
:
Maxtor 6Y080L0
PIO-4
81,964,302,336 BYTES
2005/04/08 12:08:56
2005/04/08 12:08:56
:
:
:
:
:
AT5520026DT
240/120nsec
80GB
2005/04/08 12:08:56
2005/04/08 12:08:56
TO EXIT, PRESS [MENU]
26
Quality & Value
The SmartDVR.com
(3) HDD CHANGE SETUP
Without losing data, user can use HDD from other DVRs, and HDD installed in
current DVR can be used in other DVRs.
HDD CHANGE SETUP
SAVE DVR INFO
LOAD DVR INFO
SELECT MENU :
, & [ENTER]
1) SAVE DVR INFO
Once you press ENTER button on "SAVE DVR INFO" , the DVR information will be
saved on HDD.
If the DVR information is saved properly, you can see "NOW CHANGE HDDDISK"
message on DVR.
Then power off the DVR and change with new HDD.
NOTICE : Be sure to write down the DVR information such as NTSC/PAL, MODEL
name, Channel, HDD location(PORT 1, PORT2). When you want to retrieve the
HDD(old), you must do this based on this DVR information.
2) LOAD DVR INFO
"LOAD DVR INFO " : it retrieves recorded HDD from other DVR set.
- HDD retrieval procedure
1. Install HDD with new DVR and power on.
2. Press [STOP] button when the DVR is booting.
(Then, User can see “HDD CHANGE MODE-ON“message.)
3. It retrieves when user executes “LOAD DVR INFO”in Menu.
Please note that if the HDD conditions are changed between backup and retrieval
there are some possibilities losing DATA. So, please remember the above during
backup.
27
Quality & Value
The SmartDVR.com
2) TIME/DATE SETUP
Set the time and date of the DVR system. It is very important
for searching an event with time and date that this is accurately
set. Note that the time and date set by manufacturer may be
different from the local time and user must set the date and
time before recordings start. The time and date can be set by
using the direction buttons [+] [-] or the Jog Shuttle. There is
an option for selecting date, time and month formats.
3) CAMERA SETUP
CAMERA TITLE SETUP
0123456789 .ABCDEFGHIJKLMNOPQ
RSTUVWXYZ ! #-[ ]*+ -,./ :<=>?@
CAMERA01
CAMERA02
CAMERA03
CAMERA04
CAMERA05
CAMERA06
CAMERA07
CAMERA08
CAM -1
CAM -2
CAM -3
CAM -4
CAM -5
CAM -6
CAM -7
CAM -8
[ENTER] SELECT MODE
[ / ] select CAMERA
(1) TITLE: Input Title of each camera. Move to a channel you want to edit using [LEFT] or [RIGHT] direction button and
then change the title-using [-] [+] button. When modification is finished, press the [ENTER] button. To exit to
previous menu, press the [MENU] button.
(2) COLOUR: Adjust image colour
Move to each setting using
[UP][DOWN] button and adjust
using [-] [+] button or Jog shuttle.
CAMERA COLOR SETUP
CHANNEL
BRIGHTNESS
CONTRAST
SATURATION
HUE
CAMERA POSITION
CHANNEL: Select camera
BRIGHTNESS: Adjust image brightness (-32~ 31)
CONTRAST: Adjust colour contrast ( -32 ~ 31)
SATURATION: Adjust colour saturation ( -32 ~ 31)
HUE: Adjust colour hue ( -32 ~ 31)
CAMERA POSITION : Adjust camera image
to the center. If value is lower:
Left.value is higher:
Right (0~80)
SELECT :
28
1
+0
+0
+0
+0
32
, CHANGE VALUE : + -
Quality & Value
The SmartDVR.com
CAMERA ACTIVE SETUP
MOTION CONFIGURATION
CHANNEL
CH
STATUS
LIVE
REC
--------------------------------------------------------------------------01
02
03
04
05
06
07
08
ACTIVE
ACTIVE
LOSS
ACTIVE
ACTIVE
ACTIVE
LOSS
ACTIVE
SELECT :
ON
ON
OFF
ON
ON
ON
OFF
ON
01
SENSITIVITY GRADE
ON
ON
OFF
ON
ON
ON
OFF
ON
01
MOTION DISPLAY TYPE
RECORD DURATION
SELECT
, & [ENTER]
OFF
05 SEC
, CHANGE VALUE : + -
(3) CAMERA ACTIVE SETUP: With direction button, move to option to be changed, and press [ENTER] button
to select [ON/OFF]. If it is set at LIVE [OFF] and REC [ON], DVR system records, but does not show live
image of set channel.
STATUS: Shows if image from a specific channel is set for live display and recording. In normal camera
condition, it is ACTIVE, but LOSS is displayed when the cable is disconnected or camera is not working.
LIVE: Decides whether to show LIVE screen image or not.
REC: Decides whether to record relevant channel or not.
(4) MOTION SETUP: You can set sensitivity of motion detection in 4 steps, motion detection area and others in
relation to motion recording in this menu.
(4)-1. MOTION SETUP
SENSITIVITY GRADE: Adjusts motion detection sensitivity. 1(LOW) 2(MEDIUM) 3(HIGH) 4(VERY HIGH)
MOTION DISPLAY TYPE: Showing cells with motion detected differently from cells with no motion.
RECORD DURATION: Whenever motion is detected and it is set in Motion Recording mode, DVR system
records for RECORD DURATION from time motion is detected. (1sec. ~ 99 sec.) (Default duration: 5sec.)
4)-2. MOTION MASK SETUP
Set motion detection area. Direction button is for moving, [ENTER] button is for selection and MODE
button is for changing mode of MASK SETUP.
CELL: Move to the location that you want to detect and then press the [ENTER] button.
Highlighted cell area means motion detection area.
ALL ON: Set all cells as detection area. Use [ENTER] button to set.
ALL OFF: Set all cells as no-detection area. Use [ENTER] button to set
BLOCK ON: Select detection area by block. Use [MODE] button and press [ENTER] button to set ON.
BLOCK OFF: Select un-detection area by block. Use [MODE] button & press [ENTER] button to set ON.
Highlighted Area
(Motion Detection Area)
BLOCK ON [ 1 ]
Non-highlighted Area
(No Motion Detection Area)
[1/2/3/4] CHANGE CHANNEL
[
] MOVE CURSOR
[MODE] CHANGE EDIT
MODE [ENTER] EDIT, [MENU]
EXIT
29
Quality & Value
The SmartDVR.com
4) INTERVAL SETUP
Set the switching time interval for SEQ or PIP
function.(1sec. ~ 99 sec.)
SWITCHING INTERVAL
FULL SCREEN: set the sequencing switch time interval in
live full screen.
PIP SCREEN: set the sequencing switch time interval of
PIP window.
EVENT UPDATE TIME: Set the minimum time interval of event
to be listed in EVENT LIST. If EVENT UPDATE
TIME is set at 20 seconds, only following an
event that lasted longer than 20 seconds will it
be added to the EVENT LIST.
5) ALARM SETUP
Set type of alarm sensors connected to DVR unit.
N.O represents Normal Open type and N.C Normal Close type.
ALARM INPUT: Select type of alarm sensor connected to DVR
Unit (N.O or N.C). Use direction buttons [+] or [to set.
DISABLE disables alarm sensor connected to
DVR.
DURATION:
Set the duration of alarm when an alarm is
Activated. (0 seconds ~ 300 seconds)
6) EVENT POPUP SETUP
When event is activated, a full screen image will popup.
CHANNEL: Select a channel that uses an event (motion or alarm)
POPUP ON/OFF: Set a popup function to ON or OFF
EVENT: Set the type of event mode that this popup is applied to.
A: ALARM event or M: Motion event.
DURATION: Set the duration to how long the popup image is
displayed. (0 seconds ~ 60 seconds)
NOTE: If two or more channels popup at the same time, the lowest
channel number will only be displayed.
30
Quality & Value
The SmartDVR.com
7)) BUZZER SETUP
BUZZER SETUP
Set parameters for buzzer (On or Off).
Use direction button and [ENTER] button.
ALL
KEY BEEP: buzz when button is pressed.
VIDEO LOSS: buzz when video signal is lost.
ALARM ACTIVE: buzz when alarm is activated.
MOTION DETECT: buzz when motion is detected.
--
KEY BEEP
ON
VIDEO LOSS
ON
ALARM ACTIVE
ON
MOTION DETECT
OFF
User can set all buzzers at On/Off at once by
set ALL at ON/OFF.
SELECT :
, & [ENTER]
8) PASSWORD SETUP
Set user ID and password.
-Use [UP] and [DOWN] button to move to option and [LEFT]
and [RIGHT] button to set user ID.
The password must consist of a 1 to 8 digit number.
Just use numbers button from 1 to 10 on the front panel of
DVR unit. Note that 10 = 0
-To change password, user must input current password and
then input the new password. Then input again the new
password to confirm.
- Default value
ADMIN: ‘
‘(NULL)
MANAGER: ‘
1’
USER 1: ‘
2’
:
:
USER 8: ‘
9’
Change the user PASSWORD during the first operation is recommended.
Ensure that you record the new password.
SYSTEM INFORMATION
9) SYSTEM INFORMATION
S/W VERSION VER 1.0
H/W VERSION REV-B. / ES518
PRODUCT ID
01S-2039-001008-AR-01
MASTER-1
Maxtor 6Y060L0
MASTER-2
WDC WD2000JS-00NCB1
CD-R
SAMSUNG CD-R/RW SW-256B
DVR system information including firmware version,
hardware version, product ID, etc.
TO EXIT, PRESS [MENU]
31
CHAP. 5 Set Up
Quality & Value
The SmartDVR.com
5-4. RECORD SETUP
This is the most important configuration of the DVR.
Enter SYSTEM MENU-RECORD SETUP and press the
[ENTER] button.
1) RECORD CONFIGURATION
Use direction button to move and [-] [+] button to set value.
(1) OVERWRITE: Set overwrite or stop recording when
the HDD is full.
(2) MULTIPLEX: Set DUPLEX or TRIPLEX
- DUPLEX: Playback & Ethernet
- TRIPLEX: Recording, Playback & Ethernet
NOTE: Using Duplex is recommended for playback but
Duplex does not record during a search.
3) QUALITY: Set record quality. This affects disk space.
BASIC / NORMAL / ENHANCED / FINE / SUPER FINE
In Emergency record, quality is SUPER FINE.
To send more images via IP network and longer recording
times, set QUALITY to Normal or Enhanced and record at
360x288 PAL.
(4) RESOLUTION: Set recording resolution in PAL mode.
- 50 ips at 720x288 PAL 60 ips at 720x240 NTSC
- 100 ips at 360x288 PAL 120 ips at 360x240 NTSC
- 200 ips at 360x144 PAL 240 ips at 360x120 NTSC
Images recorded in 360x288 It is not possible to see those
images in full screen mode in playback. Recording in half
or quad resolution is recommended for higher recording
speed.
(5) RECORD IN ALARM: <Set record speed (skip rate) > in ALARM record mode.
(6) RECORD IN MOTION: <Set record speed (skip rate) > in MOTION record mode.
(7) CONTINUOUS RECORD: <Set record speed (skip rate) > in CONTINUOUS record mode.
Set record speed (skip rate): Set record speed (skip rate) in alarm/ motion/ continuous mode
- 1/1x, 1/2x, … … … … … … … … .. 1/999x record speed
example:
example:
example:
1/2x ) R->S->R->S…
1/3x ) R->S->S->R->S->S->R…
1/4x ) R->S->S->S->R->S->S… ( R : RECORD
example:
If record resolution is set at 360x288, 1/1x = 100ips, 1/2x = 50ips, 1/3x = 33ips etc.
S : SKIP )
32
Quality & Value
The SmartDVR.com
2) SCHEDULE SETUP
Unless you selected another recording mode, DVR system records in Schedule Recording mode. In
SCHEDULE REC SETUP, you set type of recording for every time interval of 2 hours in each day of the
week. Schedule Recording set by manufacturer is recording continuously at its full recording speed, and it
means DVR system records continuously at 50 ips overall at 720x288 resolution.
To set Schedule Recording parameters, enter into SYSTEM MENU-RECORD SETUP-SCHEDULE SETUP
and press the [ENTER] button.
(1) SCHEDULE SETUP
Set recording type for each recording time interval for a day of the week (2 hours interval).
Use [MODE] button to select edit type and move to
the time interval of a day of the week you want to
change. Press [ENTER] button to select and use [+]
or [-] button, to change the record type. To go to the
next page, use the [NEXT] button.
MODE (Edit type)
TIME CELL: Set each time interval of a day
WEEK: Set a day of the week at once
TIMEZONE: Set a time slot at once
ALL: Set page by page at once
CLEAR ALL: Clear page by page
Except when EMERGENCY record is enabled, the
DVR system records according to the SCHEDULE
Record Setup. The DEFAULT record mode set by the
manufacturer is ‘
C’which is CONTINUOUS recording
mode.
RECORD TYPE
After power on ------ Schedule record
Exit from menu ------ Schedule record
Press and HOLD [E-REC] Emergency Record ------ Schedule record
End of search or playback -------- Schedule record
After pressing [E-REC] Emergency record -------- Emergency record (Continuous recording in best
performance 50 ips at 720x288)
3) HOLIDAY SETUP
HOLIDAY SETUP
Users can set national holiday or holidays on calendar to record
just as the setting for Sunday in SCHEDULE REC SETUP.
< APR >
SUN
Use [MODE] button to select a month and direction button to
move to a day, and press [ENTER] button to set a holiday. The
colour of the date is then changed to red, as per Sunday.
EDIT HOLIDAY: Set as holiday
CLEAR MON DATA: Cancel holiday set per month
CLEAR ALL DATA: Cancel all holiday settings.
MON
TUE
000/100
WED THU
FRI
SAT
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
The maximum number of holidays that can be set is 100 days.
MODE : EDIT HOLIDAY
SELECT
, EDIT [ENTER]&[MODE]
33
CHAP. 5 Set Up
Quality & Value
The SmartDVR.com
5-5. BACK-UP
1) CDR/DVDR SETUP
User can back up the recorded data to CD or DVD using DVD writer installed in DVR.
Refer to [START] and [END] of data on HDD and set copy from time, [START], and size of data copied,
[SIZE], and move to BURN and press [ENTER] button to start copy.
System Status Messages:
- CD-RW DOOR CLOSE. CHECKING CD-R: Blank CD check
- INPUT BLANK CD: CD writer has no blank CD/DVD.
- CD-RW DOOR OPEN: Open CD-RW and insert blank CD–R or DVD-R media into drive.
- CD-R MEDIA IS DETECTED: Blank media has been inserted and detected. DVR system will display size
of blank CD-R or DVD-R.
After you set [START] time and [SIZE] in CD-R sub-menu and then select BURN, DVR system starts
copying images to CD/DVD and displays following message.
CD-RW
CD-RW
CD-RW
CD-RW
CD-RW
BURNING: START
BURNING: LEAD-IN
BURNING: IMAGE DATA
BURNING: CLOSE TRACK
DOOR: OPEN
When burning is complete, CD-R/DVD-R media will eject automatically.
To copy more images, repeat above process. In next process, [START] time in CD-R sub-menu shall be
[END] time in previous back-up, and you can copy images in series to many CDs/DVDs, as many as you
want.
Note: SIZE CHANGE Use + and – to change size per 10Mb units or LEFT and RIGHT per 100Mb units.
2) USB SETUP
User can backup the recorded data to USB Media using USB (HOST) port on front panel of DVR.
Refer to [START] and [END] of data on HDD and set start and end time of data to USB Media (
Memory Stick or USB HDD ). Select backup file size, and move to BACKUP and press [ENTER]
Button to start copy.
34
Quality & Value
The SmartDVR.com
USB SETUP
USB SETUP
HDD
HDD
START
END
USB MEDIA
START
END
SIZE
2005/AUG/07 AM04:04:12
2005/AUG/08 PM08:12:23
START
END
2005/AUG/07 AM04:04:12
2005/AUG/08 PM08:12:23
00000MB
2005/AUG/07 AM04:04:12
2005/AUG/08 PM08:12:23
USB MEDIA
START 2005/AUG/07 AM04:04:12
END
2005/AUG/08 PM08:12:23
SIZE
28 MB - > 28MB
BACKUP
BACKUP
Status message
USB STORAGE IS CHECKING
START WRITING IN USB STORAGE
EXIT : [MENU]
EXIT : [MENU]
System Status Messages
(1) If MEMORY STICK is not inserted :
- USB STORAGE IS CHECKING
- USB STORAGE IS NOT AVAILABLE
- RE-CONNECT THE USB STORAGE
- CONECT THE OTHER USB STORAGE
(2) When MEMORY STICK or USB HDD is recognized
- USB STORAGE IS CHECKING
- THERE IS A FREE SPACE ON STORAGE
- USB STORAGE IS AVAILABLE
(3) During Back-Up
- CHANGE WRITE PROTECT MODE
- START WRITING IN USB STORAGE
- FINISH WRITING IN USB STORAGE
(4) Error Message
- THERE IS A PROBLEM ON USB PORT (If USB PORT fails to work properly)
- USB STORAGE IS FULL (When USB is full)
- FILE SYSTEM IS NOT SUPPORTED (If File System is not supported)
- SIZE IS LARGER THAN FREE SIZE (If back-up size is larger than free space)
Back-Up procedure is the same as CDR/DVD Back-Up.
If Back-Up size is larger than 2GB, it creates several files. (It saves in 2GB chunks).
5-6. EXTERNAL DEVICE
Set parameters of external devices connected to DVR, like Ethernet, PTZ camera, RS-232C, etc. Use
direction button to move to sub-menu and Press [ENTER] button to set.
1) TCP/IP SETUP
The TCP/IP function enables users to view live and recorded images
via the Internet or network.
(1) IP CONFIG SETUP:
This shows the network information assigned to the DVR unit. If the
DHCP setup is AUTOMATIC, the user can set the IP port only and if
the DHCP setup status is MANUAL, user must set all parameters.
For further details refer to the Remote Viewer software instructions.
35
Quality & Value
The SmartDVR.com
(2) DDNS SETUP :
- DDNS ON/OFF : Select if DDNS Function use
DDNS SETUP
- DDNS SERVERS : IP Address of DDNS SERVER.
- INTERVAL : Registered time period to DDNS SERVER.
Per D(Day) H(Hour) M(Minute)
- REGISTER : Once press [ENTER],
It automatically registered.
- DDNS STATUS : present current status by
"REGISTER OK“
"REGISTER ERROR", "NOT REGISTER"
DDNS ON/OFF
OFF
DDNS SERVER
211.062.253.087
INTERVAL
D-00 H-00 M-20
REGISTER
-------------------------------------------------------------------------DDNS STATUS
IP ADDRESS
---.---.---.---.--IP PORT
----REMAIN TIME
D-00 H-00 M-00
LAST REGISTERATION DATE
>
- IP ADDRESS : IP of last registered DVR
- IP PORT : Port of last registered DVR
- REMAIN TIME : Remain time to next registration
SELECT MENU :
, & [ENTER]
- LAST REG... DATA : Last registered time
(3) CONNECTION SETUP :
- TIME OUT :
Adjust TIMEOUT value properly to
successfully access to DVMR unit via Internet
line. If data transmission speed is high enough,
leave TIMEOUT value as set by manufacturer
(200 msec), and increase it if data ansmission
via Internet line is relatively slow. Execute
tracert (Tracing Route) in your PC for IP
assigned to DVMR unit, and you can figure
out how much TIMEOUT value increased.
- RETRY COUNT :
Set the retry number of times for network
connection.
CONNECTION SETUP
TIMEOUT
200 MSEC
RETRY COUNT
08
SELECT MENU :
, & [ENTER]
(4) DHCP SETUP :
DHCP SETUP
- DHCP MODE : If user selects AUTOMATIC,
IP automatically assigned.
DHCP MODE
If user selects MANUAL, in IP CONFIG SETUP
User selects it manually.
- DETECT IP : It only appears for AUTOMATIC.
Once press [ENTER], it automatically starts IP
Assignment.
DNS SERVER
168.126.063.001
IP ADDRESS
192.168.001.086
SUBNET MASK
255.255.255.000
GATEWAY
192.168.001.001
SELECT :
36
AUTOMATAIC
, CHANGE VALUE : + -
Quality & Value
The SmartDVR.com
(5) EVENT SERVER SETUP :
IP ADDRESS : IP Address of PC that executes
EVENT SERVER PROGRAM.
IP PORT : PORT of PC that executes
EVENT SERVER PROGRAM
EVENT SERVER TYPE :
It is the way to transmit data to SERVER
by "OFF", "EVENT" or "MINUTE“,
when Event is triggered in DVR or by scheduled time.
EVENT SERVER SETUP
IP ADDRESS
IP PORT
EVENT SERVER TYPE
INTERVAL
EVENT GMT TYPE
192.168.001.072
09988
OFF
--GMT+00:00
"EVENT“: It transmits by the number of EVENT.
"MINUTE“: It transmits each scheduled time.
INTERVAL: If EVENT SERVER TYPE is "EVENT"
User can select from 1~512.
If EVENT SERVER TYPE is "MINUTE“, User can select
from 1 ~ 60 mins.
SELECT :
, CHANGE VALUE : + -
EVENT GMT TYPE : User can set currently installed
location(DVR) of GMT.
(6) NVS SETUP
NVS SETUP
BITRATE :
DATA SIZE from NVS. The bigger it set, the better its
quality, but sometimes motion is not smooth.
(Set Value : 100K ~ 2500K, can be adjusted by 50K)
BITRATE
GROUP OF PICTURES
FRAMERATE
RESOLUTION
0500 Kb
010
10
640*480
GROUP OF PICTURES :
Image (I frame,P frame) from NVS. The bigger it set,
the better its quality.
SELECT :
, CHANGE VALUE : + -
FRAMERATE :
DATA RATE from NVS. The bigger it set, the better its quality, but image quality is not good.
RESOLUTION :
DATA RESOLUTION from NVS. Such as 160*120, 320*240, 640*480.
* In order to work NVS properly, above value should be adjusted according to Network bandwidth
37
Quality & Value
The SmartDVR.com
2) RS-232C SETUP
User can control the DVR via RS-232C port. Connect DVR to PC
via RS-232C port and user can control DVR using keyboard of
PC. This function is mainly for programmer who wants to control
DVR as part of many devices connected to a PC system.
NOTE: THIS IS NOT CURRENTLY SUPPORTED.
3) PAN/TILT SETUP
The DVR is capable of operating PTZ control via a number of protocols:
PELCO-D
AECD-2000
HMC 250
YOKO
TBT
MERIT-LI LN
M-CONTROL
NEOTECH-A
DRX502A
VIDO AU-GXX
ACCUDOME
ON-D
D-MAX
SU320
NOVUS-C1
HID2404
SCC-641
PELCO-P
DCS 230S
LG-MULTIX
SENSORMATIC
NOVUS-C2
To access the PTZ set up screen, first enter [SYSTEM MENU]
then [EXTERNAL DEVICE] menu followed by the [PAN TILT SET UP].
[COMMAND SETTING]
Allows the input of PTZ protocol and respective system settings.(refer to camera
manufacturers manual for further information).
38
Quality & Value
The SmartDVR.com
[SPEED SETUP]
Allows the defining of operational speeds for PTZ controls. It may be helpful to
reduce these settings when operating the DVR over a network, to reduce “over shoot”
because of network delay.
Important Note: To operate PTZ controls always ensure the PTZ channel is set to
full screen.
Initiating PTZ control
Using front panel: press [SHIFT]+[PTZ] together
Or
Using the remote: press [PTZ]
Or
Using the mouse: ‘Double Click’right mouse button on screen to bring up mouse menu and
right mouse click on PTZ icon.
In all cases a green PTZ “menu bar”will appear on the top left hand side of screen. This
displays current function.
Setting up PTZ presets using front panel
1
2
3
4
5
Once on PTZ screen press [11/GOTO] button
Select required preset number using inner jog wheel
Press [10/CLEAR] to clear previous preset.
Using curser keys ← − → ↓ move camera to desired position
Press [9/SET] button
Warning : Do not press [9/SET] unless a clear/unused preset has previously been
selected using the [11/GOTO] button, as this will overwrite previously saved presets.
Calling PTZ presets using front panel
1
2
3
Press [11/GOTO] button.
Select required preset number using ‘inner jog’wheel.
Press [11/GOTO] button.
Setting up PTZ presets using mouse
1
2
3
Select
icon on mouse menu.
Using directional arrows, move camera to desired position.
Move mouse over icon and using wheel change the top left hand menu bar to “SET
PRESET”.
39
Quality & Value
The SmartDVR.com
4
Move mouse over
programme.
5
Press
icon and using wheel select preset number you wish to
icon to save preset – “SET PRESET”will flash momentarily confirming save.
Calling PTZ presets using mouse
1
Move mouse over
2
Press
3
Press
icon and using wheel change the top left hand menu bar to
button on mouse menu to select Preset number
to call selected preset
Operating PTZ via remote control
The supplied remote offers limited PTZ functionality. The curser key will offer pan and tilt control
however the calling of presets is not possible. The PTZ menu can be scrolled using the [+] key
and selecting using [OK].
It should be noted that the DVR offers basic PTZ functionality over a number of protocols. However if
complete control is required then a PTZ Keypad, appropriate to the camera being used, should be
employed.
Calling Dome Tours etc. will depend on the preset code allocated to the specific dome eg. PTZ300 =
51preset. Refer to cameras manual for further guidance.
4) SPOT MONITOR SETUP
1) SWITCHING INTERVAL
Channel switching time (1 sec. ~ 99 secs.)
2) ALARM POP-UP
Set ON to show screen pop-up on Alarm
3) MOTION POP-UP
Set ON to show screen pop-up on Motion
4) EVENT POP-UP DURATION
Set DURATION time of Alarm or Motion
Event (1 sec ~ 99 secs.)
If events (MOTION or ALARM) happen on several channel at the same time,
channel No. 1 has the first priority to pop up. For example, if events happen on
channel No. 1, channel No. 2 and channel No. 4 at the same time, channel No. 1
pops up. If the motion disappears on channel No. 1, then channel
No. 2 pops up for the duration that you set. However, even though motion happens
on channel No. 1again within the duration, channel No. 2 still displays. If motion on
channel No.1 keeps on going even after the duration, channel No. 1 pops up again.
5)
AUDIO SETUP
Use direction button to move to channel and press [ENTER] button to set (ON/OFF).
40
Quality & Value
The SmartDVR.com
1) REC
a) ON: Record with AUDIO
b) OFF: Record without AUDIO
2) PLAY
a) ON: Audio on playback
b) OFF: No Audio on playback
6) AUDIO VOLUME SETUP
AUDIO VOLUME SETUP
INPUT VOLUME
LIVE VOLUME1
LIVE VOLUME2
LIVE VOLUME3
LIVE VOLUME4
PLAY VOLUME1
PLAY VOLUME2
PLAY VOLUME3
PLAY VOLUME4
INPUT VOLUME: Adjust VOLUME of
Recorded AUDIO
LIVE VOLUME1~4: Adjust VOLUME of LIVE
per channel.
PLAY VOLUME1~4: Adjust VOLUME of PLAY
per channel.
32
32
32
32
32
32
32
32
32
SELECT :
7) REMOCON SETUP
, CHANGE VALUE : + -
REMOCON SETUP
REMOCON TYPE
REMOCON TYPE: User use it to operate
many DVRs installed at the same site and
select each different TYPE.
S TYPE
N TYPE, S TYPE, U TYPE 1 ~ U TYPE 6:
Total 8 TYPE Selectable.
SELECT :
5-7. FACTORY DEFAULT
ALL
SCREEN DISPLAY
Reset all system parameters as per
manufacturer’
s settings. Use this option when
adding a new HDD or following problems with
changes made to system. Use direction button to
move and Press [ENTER] button to change
parameters. Then select RUN, Press [ENTER]
button for actual Factory Default setting.
CAMERA SETTING
MOTION SETUP
PAN TILT SETUP
SCHEDULE SETUP
CONFIGURATION
RUN
41
, CHANGE VALUE : + -
Quality & Value
The SmartDVR.com
5-8. LANGUAGE SETUP
The menu can be displayed in a number of languages. Press [ENTER] button to select language.
42
Quality & Value
The SmartDVR.com
CHAP. 6 Network Setup
6-1. DVR Network Configuration
Please call your Internet provider to identify what type of service they are providing for you. You will need to know the
following;
Upload speed – For your own knowledge for expected frame rates
Download speed – For your own knowledge for expected frame rates
Addressing – For determining the addressing method you will need to make
Router On Site – For connecting to the outside world
NOTE: For remote viewing we recommend using a Broadband ADSL connection with an external I.P address (supplied
by your Internet provider). You will probably need to install a modem/router for Internet connection sharing and remote
access.
PLEASE verify Internet access after installing any new equipment (routers, switches, modems, etc.). If possible, use a
PC on the network to verify that an Internet connection can be made and that all current configurations on any
equipment are up and working properly. Do this before doing ANY configurations with the DVR. We are assuming that
your current equipment is configured properly for Internet access.
PC’s TCP/IP Setting
Before configuring the DVR, please fill out the information below if applicable;
Choose any PC on your network and determine its TCP/IP settings;
IP Address: ________________________________________ (ex.192.168.1.5)
Subnet Mask: _______________________________________ (ex. 255.255.255.0)
Default Gateway: ____________________________________ (ex.192.168.1.1)
The following pages containing several network scenarios will clarify the network setup of the DVR; follow
the instructions for configuring and accessing your DVR via TCP/IP.
43
Quality & Value
The SmartDVR.com
1) Static I.P Address from an Internet Service Provider
Configure the DVR to operate with a modem router.
Configure the DVR as follows:
a. It is assumed you have a PC working on Broadband Internet.
b. Check IP address in P.C and record IP Address, Subnet Mask & Gateway Address.
Example: IP Address 192.168.1.100 Subnet: 255.255.255.000 Gateway: 192.168.1.1
c. Connect LAN cable from router to DVR.
d. Assign DVR a private IP address Example : 192.168.001.105
You need to assign the DVR an IP address similar to PC. The IP address you assign must be unique
but the first three levels must match your local network. When configuring the DVR’
s IP address
information, the version of firmware within the units may display the IP addresses differently. For
simplicity 192.168.1.105 may have to be configured as 192.168.001.105
1. Enter the DVR Menu – Go to EXTERNAL DEVICE - Go to TCP/IP SETUP
2. Enter IP CONFIG SETUP
3. SET IP ADDRESS (see above), IP PORT: 50000, GATEWAY 192.168.1.1(example)
(Router base address), SUBNET MASK: 255.255.255.000 (example) - Assign the DVR the
same exact subnet mask as your PC.
4. Please DO NOT configure MAC ADDRESS but set DHCP SETUP to MANUAL.
5. EXIT MENU.
6. Now turn Router off and on. This will take about one minute to reset.
7. Your DVR is now ready for access via the local PC using the IRS Software. Refer to your
modem/router manual for instructions on how to configure it to allow incoming Internet access.
8. If you fail to access DVR check all steps again.
9. If access speed is too slow and connection fails after access then:Go into MENU – EXTERNAL DEVICE – TCP/IP SETUP – CONNECTION SETUP
Increase TIMEOUT value if Internet line too slow. You can estimate minimum speed by going
into your PC DOS Command Mode and executing TRACERT on the DVR IP address. Now add
together all msec values displayed and use this as a base level.
44
Quality & Value
The SmartDVR.com
Dynamic IP Address from an Internet Service Provider
Customers using a dynamic I.P address on their Broadband connection are advised to source a
modem/router supporting “Dynamic DNS”within its firmware and to refer to the instructions provided
with that router in order to configure that service.
45
Quality & Value
The SmartDVR.com
CHAP 7. IRS (Integrated Remote Station)
MAIN INTERFACE
IRS SETUP Inputs Information for IRS network connection.
DVR SETUP Changes DVR setting over a network.
VIEWER
Enables to show live image display.
BACKUP
Enables to back up recorded images in DVR to your PC.
PLAYER
Enables to back up recorded images on your PC. (AJP file)
TRANSMITER Enables to control DVR using virtual key like controlling actual
DVR remotely.
CLIENT
CMS
Enables to control LIVE, PTZ control, Playback in DVR remotely.
Enables to have multi access for showing live images of many
DVRs. (Additionally, enables to search and show recorded image
display for one DVR.)
46
Quality & Value
The SmartDVR.com
7-1. IRS SETUP
MANUAL
DDNS
Select “Manual”to input IP address and port number manually.
Select “DDNS”to use IP address and port number that you already
registered in DDNS Server.
MEMBER ID
NAME
Input member ID that you registered in DDNS Server.
Input DVR name that you registered in DDNS Server.
ADDRESS
PORT
Input IP address manually.
Input Port number manually.
LOGIN
ID
Password
Input DVR ID which has been set in DVR already. (Input ‘
admin’
.)
Input password of DVR.
47
Quality & Value
The SmartDVR.com
7-2. DVR SETUP
User can change some settings of DVR listed below over a network.
(Active Camera, Alarm, Buzzer, Interval, Password, Record Configuration, Record Schedule)
MANUAL
Input IP address and port number of DVR manually.
ADDRESS
Input IP address of DVR manually.
PORT NUMBER Input port number of DVR manually.
LOGIN
ID
PASSWORD
Input DVR ID which has been set in DVR already. (Input ‘
admin’
.)
Input password of DVR.
CLOSE Click “CLOSE”to exit.
48
Quality & Value
The SmartDVR.com
7-3. VIEWER
1
2
3
4
6
5
1. DVR connection setup : Input network information to connect.
(IP / PORT / ID / PW)
2. Network Connection
a) CONNECT : Click this button to connect to DVR & see live view over a network.
b) DISCONNECT : Click this button to disconnect.
3. System Information : Displays connection status and operating Information.
4. PTZ Control : Command PTZ Camera connected to DVR remotely.
( To command PTZ remotely,User must complete PTZ setting in DVR)
5. Channel button : Selects ch that displays in full screen.
6. Screen division : User can select screen division.
49
Quality & Value
The SmartDVR.com
7-4. BACKUP
1) To execute BACKUP, input IP Address & Port and click ‘
Connect Test’button.
2) After Connect Test is done, you can see ‘
Success Connect Test!’message. Then,click ‘
lock’button
and click ‘
Set Backup Time’button.
50
Quality & Value
The SmartDVR.com
3) Now you set ‘
Start Time’
,‘
End Time’
,‘
Save File Path’
,‘
File Size’and click ‘
Apply’
.
4) After finishing time setting, click ‘
Start Backup’to start backup. Then, you can see the backup on the
path that you chose.
51
Quality & Value
The SmartDVR.com
7-5. PLAYER
1
2
3
4
8
5
7
6
1. Time Display : Displays current time.
2. Recorded data display : Displays start time & end time of recorded data.
Also, displays operating status during playback.
3. Screen display : Selects full screen mode or split mode and displays full screen for each ch.
4. Audio : Set Audio On/Off.
5. Function buttons
a) OPEN : Selects bakuped file.( AJP File )
b) EDIT : Enables to edit backup image,save and print.
d) AVI SAVE : Save backup images in AVI file format.
c) EXIT : Ends backup player.
6. Operation buttons : Search for recorded data.
a) Go to the beginning of recorded data and play.
b) Fast backward playback.
c) Backward playback.
d) Pause.
e) Forward playback.
f) Fast forward playback.
g) Go to the end of recorded data and play.
7. Playback speed setting button : Able to adjust playback spped by using upper/ lower buttons.
a) SPEED : decides playback speed.(1/4X,1/2X,1X,2X,4X,8X,16X)
b) DELAY : adjusts playback interval. The higher, the slower.(1, 2, 4, 8, 16, 32)
8. Play bar : Enables to search recorded data by using this bar.
52
Quality & Value
The SmartDVR.com
Image EDIT
1. EDIT TOOL : User can adjust color tone of copied images using these buttons.
- Contrast
: make bright part of image brighter and dark part of image darker
: To reduce light and shade, lower contrast a little
- Brightness
: make an image brighter
: make an image darker
- Sharpness
: gives sharp-edge effect
- Blur
: make an image soft.
- Operation buttons
: saves data in JPEG file format.
It is saved in the folder where player is installed.
: User can print current image selected.
2. EDIT : Return to player mode.
53
Quality & Value
The SmartDVR.com
AVI SAVE
1
2
1. OPTION : Used to save data in AVI file format.
- CHANNEL : Selects channel.
- FRAMERATE : Decides frames per second of data to be saved.
- SIZE : Decides the size of data to be saved automatically.
- START : Starts saving.
- STOP : Stops saving. Once stopped, ‘
C:\WEB_BACKUP’folder is opened automatically.
2.
AVI SAVE : Opens ‘
option’setting to start AVI saving. Closes ‘
option’setting after finishing
AVI saving and go back to player mode.
54
Quality & Value
The SmartDVR.com
7-6. TRANSMITTER
1
2
3
4
5
1. DVR Connection Setting : Inputs information for DVR Network connection .
Check ‘
IP / PORT / ID / PW’information.
2. Network Connection
a) CONNECT : Network connection to DVR. ( User can see live image of DVR. )
b) DISCONNECT : Network disconnection from DVR.
c) SETUP : User can change or set ‘
NVS Setup’of DVR System Menu.
3. System Information : Displays DVR Connection and System Operation Information.
4. PTZ Control : User can control PTZ camera connected to DVR remotely.
( To control PTZ remotely, user must set PTZ setting in DVR in advance.)
5. DVR Virtual Key : To use Virtual Key that works the same function as DVR to control DVR
remotely.
a) Bitrate: shows received data from network. Please refer to “set up”in Network Connection.
b) AUDIO: it currently does not support. It will be supported soon.
55
Quality & Value
The SmartDVR.com
SETUP (NVS Setup)
Bitrate(Kb/s)
DATA SIZE from NVS. The bigger it set, the better its quality. But sometimes image is not
smooth.
(Set Value : 100Kb ~ 2500Kb, can be adjusted by 50K)
GOP
Image (I frame, P frame) from NVS. The bigger it set, the better its quality.
Frame Rate
DATA RATE from NVS. The bigger it set, the better its movement. But sometimes image is
not smooth.
Resolution
DATA RESOLUTION from NVS. Such as 160*120, 320*240, 640*480.
* In order to work NVS properly, above value should be adjusted according to Network
Condition.
* Please refer to ‘
bitrate’displayed in TRANSMITTER when user set.
56
Quality & Value
The SmartDVR.com
7-7. CLIENT
1
2
3
4
8
7
6
5
1. Power button : Press the Power switch to exit the program. Please disconnect the live feed
before powering off the software
2. Status window : Display’
s the current time and date based. The date is in the format :
Year/Month/Day.
You will also see the status of your connection.
3. Setting, Playback, and Sequence buttons :
a) Setting : Enables the software configuration screen.
b) Playback : Enables the remote playback screen.
c) Sequence : When in single channel view, hitting the sequence button will
sequence through all active channels at a speed specified in the settings menu.
4. PTZ control : You can control a PTZ camera via the software with these controls.
a) First, you must input or configure the specific PTZ protocol into the software in
order to communicate with the PTZ device.
b) When you press any of the controls for the PTZ, please press and hold the
button for 1-2 seconds per instance to compensate for the data transmission
rate. If you do not and instead simply click the PTZ buttons, you may get
undesired results
c) The plus and minus buttons send the PTZ commands to the corresponding PTZ
camera ID.
5. Channel number button : Select the channel that you want to view based on what Screen Division
view is enabled.
6. Screen Division button : Select how many channels to view simultaneously (single,4-split,9-split,
or 16-split). When you select a view you will see the Channel Numbers highlighted
which determine what channels are currently being viewed.
7. Disconnect button : Press this button to disconnect from the DVR unit. Then you may power off the
software.
8. Connect button : Press the Connect button to view the live images from the DVR. These are the
same images being displayed on the monitor of the DVR, with a delay depending on
your Internet connection at both the DVR location and from where you’
re currently
accessing.
57
Quality & Value
The SmartDVR.com
IP/PORT Setting Screen
MANUAL
DDNS
Input IP address and PORT manually
Receive IP address and PORT from DDNS Server.
For further information of DDNS, please contact your vendor.
Name
Address
PORT
ID
Password
Name of IP address on the list.
Input IP address which is set on DVR
Input PORT which is set on DVR
Input ID which is set on DVR. (Please input ‘
admin’
.)
Input password which is set on DVR
IP List
It shows IP list which user input manually.
Select Button Select IP and PORT on the list.
Save Button Save IP and PORT on the list.
Delete Button Delete IP and PORT on the list.
58
Quality & Value
The SmartDVR.com
PTZ/SAVE Setting Screen
Circular Monitoring Interval : This indicates the speed of the channels sequence when the
SEQUENCE button is used from the main interface.
Scan Rate
: Set speed of playback.
PTZ TYPE
: Select PTZ camera which is connected to DVR.
PTZ Baud Rate : Enter the Baud Rate of your PTZ camera.
Set Path to Save Downloaded image : Determines the location and folder on your PC where the
downloaded video clips are stored.
Run in full screen mode : When checked, this will enable the program to re-adjust the interface to
completely fill your computer screen.
59
Quality & Value
The SmartDVR.com
7-7 CMS
1
2
3
4
7
5
6
8
9
10
11
12
13
1
CMS Setting : CMS Setting. (User can set DVR Registration here for multi-access.)
2
Group Setup : Among multi-access DVRs, User can set a group of specific channels
for live monitoring.
3
Search : Playback and search recorded image of one DVR.
4
View Tree : If No11 is not displayed,it will be displayed again.
5
View Event : If No 12 & 13 is not displayed, it will be displayed again.
6
Exit : Exit from CMS.
7
Screen Division : Set number of channels displayed in CMS.
8
Rotation : Sequence images.
9
Auto Rotation : Automatic image sequence (In ‘
CMS Setup’
, adjust Auto Change
Value.)
.
10
PTZ Control : PTZ control.
11
DVR Information : Displays multi-access DVR camera at Site or Group.
12
Network Condition : Displays network information of multi-access DVR.
13
DVR Event Information : Displays event information of DVR.
60
Quality & Value
The SmartDVR.com
DVR Registration and Screen Display
1) To connect DVR, from main screen select ‘
CMS Setting > Site setup > ‘
Registering Site’
, and then,
register necessary information for DVR connection as below.
(Registration is the same as ‘
IRS SETUP’
.)
2) After registration, user can display specific channel or select whole site by dragging Mouse as below.
61
Quality & Value
The SmartDVR.com
DVR Group Setup
1) After finishing DVR registration, click ‘
Group Setup’in Main Screen.
2) Click ‘
Add Group’and input group name. Drag camera channel user wants as shown below, and
set channel displays in Group and click ‘
Save Array’to setup group.
62
Quality & Value
The SmartDVR.com
1 2 3 4
7. Programmer reference
1)
6 7 8 9
Connector Pin Assignment
No
5
RS-232C
Description
No
Description
1
DCD
Data Carrier Detect
6
DSR
Data Set Ready
2
RxD
Receive Data
7
RTS
RS232C:Rx/Tx data
3
TxD
Transmit Data
8
CTS
RS232C:Rx/Tx data
4
DTR
Data Terminal Data
9
5
GND
Signal Ground
2)
RS232 ASCII-CODE
The information regarding ASCII codes for programmers is only supplied as reference material
and is not supported. We regret we cannot offer any assistance about issues concerning these
commands nor can we guarantee the integrity of the information supplied.
The following table is based on the 16 channel DVR and all ASCII code is 1 Byte.
REC
‘
R’ DOWN
‘
J’
PTZ
‘
T’
KLOCK
‘
C’
CH5
‘
5’
CH12
‘
@’
STOP
‘
S’
LEFT
‘
H’
ZOOM
‘
Z’
ULOCK
‘
O’
CH6
‘
6’
CH13
‘
#’
PLAY
‘
P’
RIGHT
‘
K’
FRZ
‘
F’
QPLAY
‘
Y’
CH7
‘
7’
CH14
‘
$’
PAUSE
‘
A’
NEXT
‘
N’
MODE
‘
D’
CH1
‘
1’
CH8
‘
8’
CH15
‘
%’
Search
‘
E’ ENTER
0x0d
PIP
‘
I’
CH2
‘
2’
CH9
‘
9’
CH16
‘
^’
MENU
‘
M’
-
‘
<’
SEQ
‘
Q’
CH3
‘
3’
CH10
‘
0’
UP
‘
U’
+
‘
>’
J.SHU
‘
L’
CH4
‘
4’
CH11
‘
!’
Jog / Shuttle
When [ACTIVE] LED is on, Jog/Shuttle is ready to be activated by the commands below.
Shuttle 0 degree
Shuttle Right 10 degree
Shuttle Right 20 degree
Shuttle Right 30 degree
Shuttle Right 40 degree
Shuttle Right 50 degree
Shuttle Right 60 degree
Shuttle Right 70 degree
Jog Minus
“&>0”[enter]
“&>1”[enter]
Shuttle Left 10 degree
Shuttle Left 20 degree
“&<1”[enter]
“&<2”[enter]
“&>2”[enter]
“&>3”[enter]
“&>4”[enter]
“&>5”[enter]
“&>6”[enter]
“&>7”[enter]
Shuttle Left 30 degree
Shuttle Left 40 degree
Shuttle Left 50 degree
Shuttle Left 60 degree
Shuttle Left 70 degree
Shuttle Left 80 degree
“&-”[enter]
Jog Plus
“&<3”[enter]
“&<4”[enter]
“&<5”[enter]
“&<6”[enter]
“&<7”[enter]
“&<8”[enter]
“&+”[enter]
Shuttle: After inputting a command once, it will keep performing the command until next
command received.
Jog: This is a one time operation command like a press button.
63
Quality & Value
The SmartDVR.com
Key Release for PTZ function
power on , light on
“1”
power off , light off
“2”
iris open
“3”
iris close
“4”
focus near
“5”
focus far
“6”
zoom in
“7”
zoom out
“8”
set preset
“9”
clear preset
“0”
goto preset
“!”
auto scan
“@”
tilt up
“u”
tilt down
“j”
pan left
“h”
pan right
“k”
“&Z”
To stop transmitting the code to DVR via RS232.
1) Set preset
“T”
“U”, “J”, “H”, “K” (To move to required position)
“&Z”
“&+”,”&-“ (To set other preset point)
“9”(set preset)
2) Clear preset
“T”
“0”
“&Z”
“&+”,”&-“ (To choose preset to delete)
“enter”
“!”
“&Z”
“&+”,”&-“ (To go to preset required)
“enter”
3) Goto preset
“T”
Reference
1. Functions where the OSD [xx] to the right of the function are not seen, pressing “1”or “2”will bring
it up.
2. Operations such as ‘
clear preset’take effect after pressing the ‘
0’key causing the last preset to be
deleted even though it may not be the desired action. Instead use the next key ‘
N’until ‘
clear
preset’is up then choose the preset to be deleted followed by enter.
3. For units lacking a front panel jog shuttle the ‘
15/F3’and 16/F4’ASCII front panel equivalent can be
used.
64
Quality & Value
The SmartDVR.com
CHAP. 7 Specifications
CHAP. 9 Specifications
•The best picture quality in Playback (JPEG-2000)
•Real time live display on all channels
•8 channel video 240(200) ips recording capability •Triplex
(Recording/Playback/Ethernet)
•Multi-language menu
•Remote monitoring and download through network
•Convenient search function with Jog-shuttle
•USB (Device) port for firmware upgrade
•Easy PTZ camera control by pre-assigned buttons
•Password Protection
•Remote Controller
Multiplex function
Storage
Internal
Capacity
Video
Inputs
Outputs
HDD
CD-R/DVD-R
Triplex (Playback/Recording/Ethernet)
Up to 2 HDDs with no capacity limitation
For backup
Composite
Composite
VGA
Loop-through
Compression
Comp. Rates
(Image size
fixed)
8Ch
2Ch (Monitor/Spot Monitor)
1Ch (Supporting TFT LCD Monitor/Option)
8Ch
JPEG-2000(Record), H264(Network)
Basic
Normal
Enhanced
Fine
Super Fine
Display Speed
Real Time Display
Record/Search Record Mode
Schedule (Time, Motion, Alarm), Emergency
Search Mode
Event Search,Date/Time,Search Bar(Jog/Shuttle)
Record Speed (NTSC/PAL)
Full (120/100), Dual(240/200), Quad(480/400)
Record Resolution (PAL)
Full (720/288), Dual(360x288), Quad(360x144)
Multi-language
English,Spanish,German,French,Italian,Russian,Dutch,Polish,Portuguese.
Switching Interval
1 ~ 99 seconds selectable
Line Division Screen
1 / 4 / 9 split
Digital Zoom, Freeze, PIP, SEQ, Event Popup
Alarm
Inputs
4 Alarms (NO/NC selectable in SETUP menu)
Outputs
1 (NO/NC)
Post Alarm
Duration of Alarm Output: 1 ~ 300 secs
Motion Detection
Area division: 16 x 12 / Detection 32 x 24
Network
Ethernet(TCP/IP), Remote Viewer provided
Backup
VCR,CD-R, DVD-R, Download via TCP/IP
PTZ Control
RS485, Key Control
Firmware Upgrade
USB port for firmware upgrade, CD-R/DVD-R
Serial Interface
RS485
For PTZ camera control
RS232C
For operation using PC keyboard- not supported
Audio
Input
4Ch Microphone Input
Output
1Ch Speaker Output
Power Requirements
DC 12v 6.67A adaptor
Weight
8.5Kg
Dimensions (Wide x Height x Depth)
436 x 396 x 88
Packing
600 x 520 x 180
65
Quality & Value
The SmartDVR.com
1. NORMAL Type
CHAP. 10 Remocon Key Definition
MENU
M enu /E xit Me nu
MODE
S cre en D ivision / Cha ng e M ode
FRZ
Free ze
SEQ
S EQ
ZOOM
ZO O M
PIP
P IP (P icture in P icture )
PTZ
P TZ
I
I
S low B ackw a rd P layba ck
S low Fo rw a rd P la yba ck
II
II
1 fram e rew in d
1 fram e forw ard
Fa st B ackw ard Playback
Fa st Fo rw ard P layback
Em ergen cy R e cord in g
S to p Play / E xit
SEA RC H
Search Menu
Decrease Value/Change PTZ Ch
-
Increase Value / Change PTZ Ch
+
Change Ch / Change PTZ Command
P LA Y
II
P AU SE
N EX T
Move menu items & Change Value
Move menu items & Change Value
Move menu items & Change Value
Move menu items & Change Value
Enter Menu & Select
4-SPILT
EN TE R
4-SPL IT
9-SPILT
9-SP LIT
16-SPILT
16-SPL IT
Change Audio Ch
AU D IO
1~9, 0
Select Ch / Set Num ber
+10
For selecting Ch10~16
Q.Play
Quick Play
There are various remote controller
types supplied with this equipment.
Please access related documentation.
66
Quality & Value
The SmartDVR.com
CHAP. 10 Remocon Key Definition
F1
F2
F3
F4
PTZ
PTZ On/Off
SEARCH
Search Menu
MENU
Menu
2. SINGLE Type
PTZ CONTROL
SET
SET PRESET
CLEAR CLEAR PRESET
GOTO GOTO PRESET
AUTO AUTO PAN
OSD DISPLAY On/Off
4-SPLIT
9-SPLIT
16-SPLIT
1~9
0
ESC
FUNC
Select Ch / Input Number
Indicates 2 digits
‘
0’+ ‘
0’= ’
10’
‘
0’+ ‘
1’= ’
11’
Emergency Recording
<No functions>
MODE Screen Division / Change Mode
Arrows Move menu items & Change Value
OK
Enter Menu & Select
CH + / - Change Channel
+/Change Value
AUDIO Change Audio Channel
I
I
II
SEQ
FRZ
PIP
ZOOM
67
Playback location
Backward Playback
Start Playback / Fast Forward
Go back to the end
Decrease Playback Speed
Pause
Stop
Increase Playback Speed
SEQUENCE
FREEZE
Picture In Picture
ZOOM
Quality & Value
The SmartDVR.com
4 Channel Record time table.
Basic
14K
Normal
19K
PAL
Enhanced
24K
Fine
29K
Super Fine
32K
80
33 Hr
25 Hr
19 Hr
16 Hr
15 Hr
160
67 Hr
49 Hr
39 Hr
32 Hr
29 Hr
250
104 Hr
77 Hr
61 Hr
50 Hr
46 Hr
300
125 Hr
92 Hr
73 Hr
60 Hr
55 Hr
400
166 Hr
123 Hr
97 Hr
80 Hr
73 Hr
500
208 Hr
154 Hr
121 Hr
100 Hr
91 Hr
600
250 Hr
184 Hr
146 Hr
120 Hr
109 Hr
800
333 Hr
246 Hr
194 Hr
160 Hr
146 Hr
1000
416 Hr
307 Hr
243 Hr
200 Hr
182 Hr
Basic
14K
Normal
19K
PAL
Enhanced
24K
Fine
29K
Super Fine
32K
80
17 Hr
12 Hr
10 Hr
8 Hr
7 Hr
160
33 Hr
25 Hr
19 Hr
16 Hr
15 Hr
250
52 Hr
38 Hr
30 Hr
25 Hr
23 Hr
300
62 Hr
46 Hr
36 Hr
30 Hr
27 Hr
400
83 Hr
61 Hr
49 Hr
40 Hr
36 Hr
500
104 Hr
77 Hr
61 Hr
50 Hr
46 Hr
600
125 Hr
92 Hr
73 Hr
60 Hr
55 Hr
800
166 Hr
123 Hr
97 Hr
80 Hr
73 Hr
1000
208 Hr
154 Hr
121 Hr
100 Hr
91 Hr
HDD Capacity
(GB)
8/16 Channel Record time table.
HDD Capacity
(GB)
68
Download PDF