Jumpking JP1414C 14ft JumpPOD® Trampoline and Enclosure COMBO Unit Owner's Manual
Add to my manuals24 Pages
advertisement
14‘ JumpPOD JP1414C
WARNING
Read the assembly, installation, care, maintenance, and use instructions in this manual prior to assembling and using this trampoline/enclosure. Save this manual for future reference.
USER’S MANUAL . . . . . . . . . . . . . 3
Assembly, Installation, Care,
Maintenance, and Use Instructions.
WARNING: The trampoline/enclosure is designed for users weighing 100 kg(220 lbs.)
or less.
Ladder is not supplied with trampoline.
YJ USA Corp.,
3970 Lindbergh Drive Addison, TX 75001
1-877-927-8777
www.jumpking.com
2
QUESTIONS?
If you have questions after reading this manual, please call our toll-free
Customer Hot Line. The trained technicians on our Customer Hot Line will provide immediate assistance.
Customer Hot Line: 1-877-927-8777
Monday–Friday, 8 a.m.–5 p.m.
REPLACEMENT
PARTS
www.jumpking.com
CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 4
WARNING LABEL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . .6
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TRAMPOLINE/ENCLOSURE SAFETY INFORMATION . . . . . . . 7
USE AND INSTRUCTIONAL MATERIAL . . . . . . . . . . . . . . . . . . 11
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . 21
EXPLODED DRAWING AND PART LIST . . . . . . . . . . . . . . . . .22
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . .22
3
1. The owner and supervisors of the trampoline
are responsible to make sure all the users are
aware of practices specified in this manual.
2. Trained Spotter supervision is recommended.
14. Misuse and abuse of the trampoline is dan-
gerous and can cause serious injuries.
15. Use the trampoline only with mature, knowl-
edgeable supervision.
3. Place the trampoline on a level surface before
use.
16. Climb onto and off the trampoline. Do not
jump onto it or off it. Do not use the trampo-
line as a springboard to other objects.
4. Must place the trampoline on lawn, bark wood
chip, sand or cushioning materials.
5. Adequate overhead clearance is essential. A
minimum of 7.3 m (24 ft) from ground level is
recommended. Provide clearance for wires,
tree limbs, and other possible hazards.
6. Maintain a free space of minimum 2500mm on
all sides of the trampoline. This area should not
included concrete, bitumen, brick, or other hard
surfaces as these can cause serious injuries.
17. Injury may result from encountering the
frame or falling through the springs while
getting onto or off the trampoline or while
jumping. Stay in the center of the bed when
jumping. Do not use the trampoline without
the frame pad securely in place to cover the
frame. The frame pad is not designed or in-
tended to support the weight of the user. Do
not step or jump directly onto the frame pad.
7. Lateral clearance is essential. Place the tram-
poline away from walls, structures, fences, and
other play areas. Maintain a clear space on
sides of the trampoline.
18. The trampoline is a rebounding device that
propels the user to unaccustomed heights
and into a variety of body movements. Re-
bounding off the trampoline, striking the
frame or springs, or improperly landing on
the bed may cause injury.
8. Use the trampoline in a well lighted area. Art-
ificial illumination may be required for indoor or
shady areas.
19. Do not attempt or allow somersaults. This
can result in a broken head, neck, back, or
leg. Landing on the head or neck can cause
serious injury, paralysis, or death, even land-
ing on the middle of the bed.
9. Secure the trampoline against unauthorized
and unsupervised use. If an access ladder is
used, it should be removed when the trampol-
ine is not in use.
20. Do not use the trampoline while under the
influence of alcohol or drugs. These sub-
stances impair reaction time, judgement,
and physical coordination.
10. Inspect the trampoline and enclosure before
each use, and replace any worn, defective, or
missing parts. Make sure the netting, enclos-
ure tubes, and foam sleeves are correctly
positioned.
21. Do not jump on the trampoline while holding
an object, particularly one that is sharp or
breakable.
11. Remove any obstructions from beneath the
trampoline.
22. Bounce only when the surface of the bed is
dry. Wind or air movement should be calm
to gentle. The trampoline must not be used
in gusty or severe winds.
12. The trampoline is designed for users weighing
100kg (220 lbs.) or less. The trampoline is not
recommended for use by children under 6
years of age.
23. The trampoline enclosure is to be used only
as an enclosure for a round trampoline.
13. Do not allow more than one person on the
trampoline. Use by more than one person at
the same time can result in serious unjury.
24. Do not attach anything to the netting that is
not a manufacturer approved accessory or
part of the enclosure.
25. Wear clothing free of draw-
strings, hooks, loops, or anything
that could get caught in the net-
ting.
26. Enter and exit the trampoline
enclosure only at the door de-
signed for that purpose.
27. Do not attempt to crawl under
the netting.
28. Do not attempt to jump over the
netting.
WARNING LABEL PLACEMENT
Label 1
29. Do not intentionally rebound off
the netting.
30. The trampoline frame and the enc-
losure are made of metal. They
are not grounded, and they will
conduct electricity. Therefore,
an electrocution hazard exists.
31. Keep all frame and heat sources
away from the product.
Label 2 focus eyes on the trampoline towards the perimeter.
The labels shown on this page have been attached to the trampoline in the indicated locations. The placard will be attached by the owner (see step 7 on page 18). If one of the labels or the placard is missing or illegible, call our Customer
Hot Line (see page 3) and order a free replacement label or placard. Attach the label or placard in the location shown.
Note: The labels and the placard are not shown actual size.
Placard
(to be attached by the owner)
For Equipment Information, Contact: YJ USA Corp,. 3970 Lindbergh Drive Adison, TX 75001.
Customer Hot Line: 1-877-927-8777. Monday - Friday, 8 a.m. - 5 p.m.
Model: JP1414C
Made In China
5
YJ USA Corp.,
3970 Lindbergh Drive Addison,
Tx 75001
Customer Hot Line: 1-877-927-8777
Model: JP1414C
WARNING PLACARD PLACEMENT
The placard shown at the right must be attached to the trampoline enclosure by the owner (see assembly step 14 on page
20). If the placard is missing or illegible, call our Customer Hot Line toll-free at
1-877-927-8777 Monday through Friday,
8 a.m. until 5 p.m. Central Time, to order a free replacement placard.Note: The placard is not shown actual size.
While keeping the head erect, focus eyes on the trampoline toward the perimeter.
For Equipment Information, Contact: YJ USA Corp., 3970 Lindbergh Drive Adison, TX 75001.
Customer Hot Line: 1-877-927-8777. Monday - Friday, 8 a.m. - 5 p.m.
Model: JP1414C
Made In China
BEFORE YOU BEGIN
Thank you for selecting a jumpPOD trampoline/ enclosure. jumpPODs are designed and crafted to line/enclosure comes equipped with warnings and instructions for the assembly, care, maintenance, and use of the trampoline/enclosure. This information must be read by all trampoline supervisors and users before any person is allowed to jump or use the enclosure on the trampoline.
If you have questions after reading this manual, please call our Customer Hot Line at 1-877-927-8777,
Monday - Friday, 8 a.m. until 5 p.m. Central Time
(excluding holidays). To help us assist you, please mention the name of the product when calling.
6
TRAMPOLINE SAFETY INFORMATION
In trampoline use, as in all active recreational sports, participants can be injured. However, there are steps that can be taken to reduce the risk of injury. In this section, primary accident patterns are identified and the responsibilities of supervisors and jumpers in accident prevention are described.
ACCIDENT CLASSIFICATION
Somersaults (flips): Landing on your head or neck, even in the middle of the trampoline bed, increases the risk of a broken back or neck, which can result in paralysis or death. Such events can occur when a jumper makes an error trying to perform a forward or backward somersault (flip). Do not perform somersaults (flips) on this backyard trampoline.
Multiple Jumpers: More than one jumper on the trampoline increases the chance of a jumper becoming injured by losing control of his or her jump.
Jumpers may collide with one another, fall off the trampoline, fall on or through the springs, or land incorrectly on the bed. The lightest weight jumper is the jumper most likely to be injured.
Mounting and Dismounting: The trampoline bed is several feet from ground level. Jumping off the trampoline to the ground or any other surface may result in injury. Jumping onto the trampoline from a roof, deck, or other object also represents a risk of injury.
Smaller children may need assistance getting onto or down from the trampoline. Climb carefully onto and off the trampoline. Do not step onto the springs or the frame pad. Do not grasp the frame pad to pull yourself onto the trampoline.
Striking the Frame or the Springs: Injury may result from encountering the frame or falling through the springs while jumping or getting onto or off the trampoline. Stay in the center of the bed when jumping.
Make sure to keep the frame pad in place to cover the frame. The frame pad is not designed nor intended to support the weight of the trampoline user. Do not step or jump directly onto the frame pad.
Loss of Control: Jumpers who lose control of their jump may land on the bed incorrectly, land on the frame or springs, or fall off the trampoline. A controlled jump is one where the landing is in the same spot as the takeoff. Before learning a more difficult maneuver, the preceding one should be performed consistently under control. Attempting a maneuver beyond present skill levels increases the chance of loss of control. To regain control and stop your jump, bend your knees sharply when you land.
Alcohol or Drug Use: The chance of injury increases when a jumper has consumed alcohol or taken drugs.
These substances impair a person’s reaction time, judgment, and physical coordination.
Encountering Objects: Use of a trampoline while other people, pets, or objects are underneath it will increase the chance of injury. Jumping while holding or having an object on the trampoline, particularly one that is sharp or breakable, will increase the chance of injury. Placing a trampoline too close to overhead electrical wires, tree limbs, or other obstructions can increase the chance of injury.
Poor Maintenance of the Trampoline: Jumpers may be injured if a trampoline is used when it is in poor condition. A torn bed, bent frame, broken spring, or missing frame pad, for example, should be replaced before anyone is allowed to jump. Inspect the trampoline before each use.
Weather Conditions : A wet trampoline bed is too slippery for safe jumping. Gusty or high winds can cause jumpers to lose control. To reduce the chance of injury, use the trampoline only under appropriate weather conditions.
Access: To prevent access to the trampoline by unsupervised smaller children, the access ladder should always be removed and stored in a secure location when the trampoline is not in use.
7
METHODS OF ACCIDENT PREVENTION
The Supervisor’s Role in Preventing Accidents
It is the responsibility of the supervisors of trampoline users to provide knowledgeable and mature supervision. They need to know and enforce all the rules and warnings set forth in this manual to minimize the likelihood of accidents and injuries and to inform users of these rules. During periods of time when supervision is unavailable or inadequate, this may require that the trampoline be disassembled, placed in a secure area, or otherwise secured against unauthorized use.
Another option that may be considered is covering the trampoline with a heavy tarp that can be secured with locks and chains. It is the responsibility of the supervisor to make sure that the placard with TRAMPOLINE
SAFETY INSTRUCTIONS (see step 7 on page 18) is kept posted on the trampoline and that jumpers are informed about these instructions.
The Jumper’s Role in Preventing Accidents
Education on the part of the user is a must for safety.
Users must first learn a low, controlled bounce and then learn the basic landing positions and combinations before proceeding to intermediate skills.
Jumpers must understand why they have to master
“control” before they can start thinking about other moves. Understanding the proper progression of skills in jumping on a trampoline must be the first lesson.
Review this manual to learn about the basic techniques for using the trampoline. Follow the rules on the placard with TRAMPOLINE SAFETY
INSTRUCTIONS (see step 7 on page 18). For further information or additional instructional materials, contact a certified trampoline instructor.
TRAMPOLINE SAFETY INSTRUCTIONS
For the Supervisor
Read the instructions before using the trampoline.
Enforce all of the safety rules and be familiar with the information in this manual to help new users learn basic jumps and all users follow trampoline safety. All trampoline users must have mature, knowledgeable supervision, regardless of the skill or age of the jumper.
This trampoline is not recommended for use by children under 6 years of age.
Inspect the trampoline before using it. Do not use the trampoline without the frame pad securely in place to cover the frame. Do not use the trampoline when it is wet or in a windy condition. A worn or damaged bed, spring, or frame piece should be replaced immediately.
Keep objects away that could interfere with the jumper.
Secure the trampoline against unauthorized and unsupervised use.
For the Jumper
Do not use the trampoline when under the influence of drugs or alcohol.
Avoid bouncing when tired.
JUMPING
Learn fundamental jumps and body positions thoroughly before trying more advanced skills. Be alert to your own limitations in the execution of trampoline skills. Review this manual to learn how to do basic jumps.
Stop your bounce by flexing your knees as your feet come in contact with the trampoline bed. Learn this skill before attempting others.
Avoid jumping too high or for too long. Always control your jump. A controlled jump is one where the takeoff and landing spots are the same.
Bounce in the center of the trampoline. Focus your eyes on the frame pad. Failure to do so may result in a loss of balance and control.
Take turns jumping, one at a time, and always have someone watch you.
GETTING ON AND OFF
Climb onto and off the trampoline; do not jump onto it or off it. Do not use the trampoline as a springboard to other objects. For additional information regarding skill training, contact a trainer certification organization.
8
TRAMPOLINE ENCLOSURE SAFETY INFORMATION
NEED FOR TRAMPOLINE ENCLOSURE SAFETY
A trampoline enclosure is a recreational product.
The information on this page and on page 10 identifies important safety precautions. The precautions are not all-inclusive, because an enclosure can be used in ways that this manual cannot cover completely.
To prevent pinches and cuts during enclosure use, a frame pad must be installed on the trampoline. (See the trampoline manufacturer’s instructions.) The frame pad must be installed before the enclosure is erected.
The frame pad reduces the chance of injury from accidental contact with the springs and frame.
USING THE ENCLOSURE SAFELY
Adult Supervision of Children
Children using a trampoline with a trampoline enclosure must be supervised by adults. Young children must be supervised constantly. Adults must pay particular attention to:
• things that children bring into the enclosure.
• children’s activities inside the enclosure.
• conditions inside the enclosure while children are using it.
• the way children get into and out of the enclosure.
Additional details of safe enclosure use are described below.
Electrocution Hazard Associated with the Metal
Frame of the Trampoline and Enclosure
The trampoline and enclosure frames are made of metal. They are not grounded, and they will conduct electricity. Lights, electric heaters, extension cords, and household electrical appliances are not permitted in or on the trampoline or enclosure.
Hazards Associated with Entering and Exiting the
Trampoline Enclosure
A trampoline enclosure installed on a trampoline is raised off the ground. The height of the enclosure increases the risk of a fall when a jumper is entering or exiting the enclosure. Young children in particular may have difficulty getting into and out of the enclosure. To reduce the risk of falling, help young children to get into and out of the enclosure.
Enter and exit the trampoline enclosure only through the door of the enclosure (the opening in the netting walls). The trampoline bed and the netting walls of the enclosure are separate pieces; jumpers, particularly young children, must not exit the enclosure by going out between the bed and the netting walls. Trying to exit in this way poses a risk of strangulation from being caught between the trampoline frame and the netting walls.
Darkness increases the chances of a fall when a jumper is entering or exiting the enclosure. Do not use the trampoline unless adequate lighting is provided.
Hazards Associated with Animals and Sharp and
Breakable Objects
To avoid damage to the trampoline enclosure and the trampoline, do not allow pets or other animals inside of the enclosure. The claws and teeth of animals can damage the netting. Do not jump on the trampoline while holding or wearing a sharp or breakable object.
9
Hazards Associated with High Winds
A trampoline with an enclosure can be moved or blown over by high winds, potentially injuring anyone in its path or anyone inside of the enclosure. If you anticipate high winds, take down the enclosure netting, and stake the trampoline frame to the ground
(see page 21), or move the trampoline and enclosure to a sheltered location.
Storing the Trampoline Enclosure Safely
Specific steps for storing the trampoline enclosure are presented later in this manual. There are specific safety precautions to be aware of when storing the enclosure.
Remove the attached tube sections as a unit, and separate them on the ground. Avoid pinching your fingers by keeping your fingers away from pinch points near the bracket assembly while you are removing the tubes from the frame.
Placing the Trampoline in a Safe Place
There must be at least 24ft (7.3 m.) of clear, open space above the trampoline bed. Do not place or store anything underneath the trampoline.
To avoid injury, the trampoline must be kept away from objects and possible hazards including electric power wiring, tree limbs, and fences. Do not place the trampoline near any other recreational devices or structures such as a swimming pool or swing set.
The trampoline must be placed on a level surface before use, and the area around the trampoline must always be well lighted.
For the Supervisor
Be familiar with the information in this manual and enforce all of the safety rules. Help new users and all users to use the trampoline and enclosure safely.
All trampoline users must have someone watch them, regardless of the skill or age of the user.
Secure the trampoline against unauthorized and unsupervised use. Keep the trampoline free of objects that could interfere with the jumper.
This trampoline enclosure is not recommended for use by children under 6 years of age or by anyone weighing more than 220 lbs (100 kg).
Use the trampoline only when the bed is clean and dry. Inspect the trampoline and enclosure prior to each use and replace any worn or damaged parts.
Use only when the enclosure netting has no holes, the clamps are tightly secured to the tubes and the frame, and the netting is properly suspended.
For the Jumper
Do not attempt to jump over the netting. Do not intentionally rebound off the netting. Do not hang from, kick, cut, or climb on the netting.
Wear clothing that is free of drawstrings, hooks, loops or anything that could get caught in the netting.
Do not attach anything to the netting that is not a
Bazoongi approved accessory or part of the trampoline enclosure.
How to Enter and Exit the Trampoline Enclosure
Enter and exit the trampoline enclosure only through the door in the netting. To enter the enclosure, first unfasten the plastic clips on the door and unzip the zippers. Place one knee on the frame pad and climb head first through the door. Refasten the plastic clips and close the zippers.
To exit the enclosure, first unzip the zippers on the door and unfasten the plastic clips. Sit on the bed of the trampoline and climb feet first through the door.
When you are through the door and sitting on the frame pad, step or jump safely to the ground. Close the zippers and refasten the plastic clips.
10
USE AND INSTRUCTIONAL MATERIAL
OVERVIEW OF TRAMPOLINE USE
The first periods of trampoline use should focus on learning fundamental body positions and practicing the eight basic bounces that are described on pages 13 and 14 in this manual.
During this learning period, jumpers should practise these basic techniques and perfect them. Braking, or checking the bounce, should be taught first and stressed as a safety measure. Jumpers should brake their jump whenever they start to lose balance or control. This is done by simply flexing the knees sharply upon landing and absorbing the upward thrust of the bed. This enables the jumper to stop suddenly and avoid losing control.
In trampoline use, the takeoff point and landing point of a good, controlled jump are in the same spot. An exercise is considered learned only when a jumper is able to perform it consistently. Jumpers should never proceed to any advanced step until they can perform all previous techniques consistently.
Allow each jumper a brief turn on the trampoline.
Extended bouncing exposes an overtired user to an increased risk of injury. Longer turns tend to lessen the interest of others waiting to jump. Clothing should consist of a T-shirt and shorts. Jumpers should wear regulation gymnastic shoes or heavy socks, or they may jump barefoot. Street shoes or tennis shoes should not be worn on the trampoline. Beginning jumpers may wish to wear loose-fitting protective clothes, such as a long-sleeve shirt and pants, until correct landings are mastered. This will reduce the chance of mat (bed) burns from improper landings on elbows and knees. No hard-sole shoes should be worn, as they cause excessive wear on the trampoline bed.
Mounting and dismounting properly should be a strict rule from the beginning. Users should climb onto the trampoline by placing their hands on the frame and stepping or rolling up onto the frame, across the springs, and onto the bed. Do not step directly onto the frame pad or grasp the frame pad when mounting or dismounting the trampoline. Users should always place their hands on the frame while mounting or dismounting. To dismount, jumpers should walk to the side of the bed, bend over and place one hand on the frame, and then step from the bed to the ground. If you have installed the optional ladder, its rungs can be used to mount or dismount. Always face the ladder and place your hands on the frame. Make sure your foot has secure contact with the ladder rung when using it.
Reckless bouncing should not be permitted. All skills should be learned at moderate heights. Control, rather than height, should be emphasized. Jumpers should be forbidden to practice alone and unsupervised.
11
INSTRUCTIONAL PROGRAM AND MODEL
LESSONS
The following lessons are examples of an instructional program. They should follow a complete discussion and demonstration of body mechanics between the supervisor and the student(s). See pages 13 and 14 for descriptions of basic trampoline skills.
Lesson 1
1. Mounting and dismounting—Demonstration and practice of proper techniques.
2. Fundamental bounce—Demonstration and practice.
3. Braking (checking the bounce)—Demonstration and practice. Braking on command.
4. Hand and knee drop—Demonstration and practice, stressing four-point landing and alignment.
Lesson 2
1. Review and practice of skills previously learned.
2. Knee drop—Half twist to the right, to the left, to the feet, and then to the knees.
3. Seat drop—Half twist to the feet. Seat drop, knee drop, hand and knee drop, repeat.
Lesson 3
1. Review and practice of skills previously learned.
2. Front drop—To save time and avoid mat (bed) burns, all students should be requested to assume the front drop position on the floor while the instructor checks for faults. Suggested progression: from hand and knee bounce, the body is extended for the landing in the front drop position, and the rebound is made to the feet.
3. Practice routine—Hand and knee drop, front drop, feet, seat drop, half twist to feet.
Lesson 4
1. Review and practice of skills previously learned.
2. Back drop—Demonstration, emphasizing the forward thrust of the hips by arching the body as one leg is brought forward from the standing (not bouncing) position, and the drop to the back with the chin held forward to the chest and the eyes forward on the frame pad. Spotting this skill is most important. Demonstration of back drop with low bounce and practice of both techniques.
Lesson 5
1. Review and practice of skills previously learned, encouraging original routines based on them.
2. Half turntable—Start from the front drop position and push to the left or right with the hands. Turn the head and shoulders in the same direction.
Keep the back parallel to the bed and the head up.
After completing a half turn, land in the front drop position.
Lesson 6
1. Swivel hips—Suggested progression: seat drop, feet, half twist, repeat; seat drop, half twist to feet, repeat; seat drop, half twist to seat drop.
2. Half turntable.
Lesson 7
The student should now be encouraged to design and organize routines, with emphasis on good form. The instructor may judge or grade students and arrange groupings for further instruction accordingly.
To stimulate interest in competition, the game of
“Trampoline Horse” can be introduced. Before the game begins, students must count off. To start the game, student number 1 performs a stunt. Student number 2 then mounts the trampoline and performs the same stunt and adds a second stunt. Student number 3 mounts and performs stunts 1 and 2 and adds a third stunt. Thus, the series of stunts is continuously lengthened. The first person to miss a stunt in the series assumes the letter “H” and starts a new series with a stunt. If a person misses again, he assumes the letter “O.” The first person to accumulate
“H-O-R-S-E” is eliminated from the game. The last remaining contestant is the winner.
Lesson planning from this point should be facilitated by contacting a certified trampoline instructor.
12
BASIC TRAMPOLINE SKILLS
Fundamental Bounce
1. Start from a standing position with your head erect and your eyes on the frame pad.
2. Swing your arms forward and up in a circular motion.
3. Bring your feet together and point your toes downward while in the air.
4. Keep your feet about 30 cm (15 in.) apart when landing on the bed.
Knee Drop
1. Start bouncing from a standing position, keeping your eyes on the frame pad.
2. Land on your knees, keeping your back straight and your body erect.
3. Come back up to an erect position.
Hand and Knee Drop
1. Start bouncing from a standing position, keeping your eyes on the frame pad.
2. Land on the bed on your hands and knees.
3. Push with your hands and come back up to an erect position.
Back Drop
1. Start from a low bounce and land on your back.
2. Keep your chin forward on your chest as you land.
3. Kick forward and up with your legs to return to an erect position.
13
Seat Drop
1. Land in a sitting position with your legs parallel to the bed.
2. Place your hands on the bed beside your hips.
3. Push with your hands to return to an erect position.
Front Drop
1. Start from a low bounce and land on the bed in a prone position.
2. Keep your head up and your arms extended forward on the bed.
3. Push with your arms to return to an erect position.
Half Turntable
1. Start from the front drop position and push to the left or right with your arms to begin turning your body in the opposite direction.
2. Turn your head and shoulders toward the direction that your body is turning.
3. Keep your back parallel to the bed and your head up.
4. After completing a half turn, land in the front drop position.
Swivel Hips
1. Start with a seat drop.
2. Turn your head to the left or right and swing your arms up in the same direction.
3. Turn your hips in the same direction as your head and arms, completing a twist.
4. Land in the seat drop position.
14
ASSEMBLY
IMPORTANT ASSEMBLY INFORMATION
• A Phillips Head screw driver is needed to
assemble trampoline/enclosure. However, a
screwdriver is not provided.
• Assembly requires two or three persons. Keep
children away from the trampoline/enclosure
until it is fully assembled.
• Use gloves to protect your hands from pinch points during assembly.
• The assembly steps refer to parts by their descriptions and key numbers (see the PART LIST on page 22). If a part is missing, see ORDERING
REPLACEMENT PARTS on page 22.
TRAMPOLINE/ENCLOSURE PLACEMENT
1. Place the trampoline/enclosure on a level surface before use.
2. Adequate overhead clearance is essential. A minimum of 7.3 m (24 ft.) from ground level is recommended. Provide clearance for wires, tree limbs, and other possible hazards.
Lateral clearance is also essential. Place the trampoline/enclosure away from walls, structures, fences, and other play areas. Maintain a clear space on all sides of the trampoline/enclosure.
3. Use the trampoline/enclosure in a well-lighted area. Artificial illumination may be required for indoor or shady areas.
4. Secure the trampoline/enclosure against unauthorized and unsupervised use.
5. Remove any obstructions from beneath the trampoline/enclosure.
6. The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in this manual.
7. The trampoline/enclosure is only to be used
as an enclosure for a round trampoline.
1. Make sure you understand the information in the box at the top of this page before you begin assembling the trampoline.
Lay Top Tube (1,2) and (3
ˈ4) on the ground as shown.
Make sure there are a T-Connector (5) on
Top Tube (1,A Marking) and a POD-Connector
(6) on Top Tube (3, B Marking). Insert the smaller end of Top Tube (3, B Marking) into the
Socket (7) on Top Tube (4,A Marking).
Insert the smaller end of Top Tube (4, A Marking) into T-Connector (5). Then insert the Top
Tube (2, B Marking) into POD-Connector (6).
1
Insert a Center (9) into the Leg (8), slide a second
Leg (8) onto the base. Tighten a Self-tapping
Screw(18) into the small hole in the Leg (8).
Insert the Leg(8) into the T-Connector (5) and insert the Leg(8) into POD-Connector (6).
1(A Marking)
Step on the Top Rail (1, 2),lift the leg, and insert the leg into the T-Connector (5) and POD-Connector (6).
You have now assembled one leg section. Repeat this step to assemble four more leg sections.
18
8
4(A Marking)
5(A Marking)
9
7
8
18
2(B Marking)
6(B Marking)
3(B Marking)
15
2. Note: This step requires two or three persons.
During this step, you will connect the four leg sections.
Hold two leg sections in the positions shown.
Insert the small end of one Top Tube (1) into the
Socket (7) on Top Tube (2).
Repeat this step until all four leg sections are connected.
2
3
7
4
5
1
2
6
7
2
7
6
8
3
1
5
7
4
8
4
5
7
1
3
7
6
2
2
6
7
1
5
7
4
3
9
3. Lay the Bed (10) on the ground inside of the assembled frame. Make sure that the two warning decals (not shown) are on top of the Bed.
Note: There are V-rings around the edge of the
Bed (10) and holes around the top of the frame.
During this step, you will attach the Bed to the frame using the included Springs (26) for holes on top of frame and for holes on bottom of frame
(see the inset drawing). Hook a spring to the
Bed(10) and using the spring pulling tool(23), pull the spring from the Bed to the hole slot in the trampoline frame with even spring tension.
To attach each Spring, you will first hook one end of the Spring into a V-ring with yellow webbing location (see the inset drawing).
3
10
Frame
26(two pcs)
26(two pcs)
Holes
V-rings
26(two pcs)
26(two pcs)
Hook the first two Spring (26) into two the V-rings
(with yellow webbing) on the Bed (10) and into the holes on the POD-Connector. Attach two more
Springs (26) with yellow webbing location directly across the Bed (with the webbing) from the first two
Spring. Attach two more Spring (26)with yellow webbing location halfway between the first/second
Spring (24), so eight Springs (26) are attached as shown. Attach four more Springs (12) (not shown) halfway between the first eight Springs(12).
Continue attaching Springs (12)halfway between the previously attached Springs,until all the Springs are attached.
Spring (12):
Hook the V-ring
23
V-ring
12
12
10
During the installations of spring, wear gloves and protective eye wear.
Yellow Spring (26):
Hook the V-ring
Frame
16
4. Lay the Frame Pad (11) on the frame. Adjust the position of the Frame Pad so the notches are aligned with the Legs (8) as shown. Be sure
4 Enclosure Frame Opening are fit to the
Enclosure Socket position.
4
Do not use the trampoline without the Frame
Pad (11), which is designed to reduce the likelihood of injury to the user from coming in contact with the trampoline frame. If you do not have a Frame Pad, contact your dealer to obtain one. Properly install the Frame Pad before using the trampoline.
11
Enclosure Frame Opening
Notches
8
9
11
8
5 Look under the trampoline and locate the pairs of straps near the edge of bed(10) and Double
D-ring and webbing near the frame.
See the inset drawing. A, B and C. Repeat this step with the remaining straps (not shown).
5
A
Top tube
Frame Pad
D-ring
B
Frame Pad
D-ring
Top tube
C
Frame Pad
D-ring
Top tube
Webbing
Webbing
Webbing
6. Thread one end of Elastic Tie-Down, then tie a knot
on V-Ring.
Repeat this step with the remaining straps which at
middle position of each pad section (not shown).
6
V-Ring
Elastic Tie-Down
V-Ring
Spring
Elastic Tie-Down
Strap with Double D-ring on the pad edge
17
7. Using the included plastic tie, attach the Safety
Placard (20) to the frame near the point where jumpers will climb onto and off the trampoline.
The trampoline is now fully assembled. Make sure that all parts are securely attached.
Familiarize yourself and all users of the trampoline with the safety precautions, use and instructional materials, and care and maintenance instructions in this manual before using the trampoline.
7
Frame
20
8. Lay a Straight Tube(14) and a Top Tube (15) with
Plastic Cap on the ground.
8
14
Make sure that the Straight Tube (14) is oriented so the small holes are in the position shown.
Slide a Foam Sleeve (17) onto each of the tubes; note that the ends of the Straight Tube (14) should not be covered.
Insert the Straight Tube (14) into the Top Tube(15).
Tighten a Self-tapping Screw (18) into the small hole in the Tube (14,15).
Assemble the remaining Straight Tubes (14), Top
Tubes (15) and Foam Sleeves (17) in the same way.
14
17
17
Small Hole
18
Tighten Self-tapping Screw
Into Small Hole
15
17
15
9
9. Insert the end of Pole (14,15) into the hole of
POD-Connector (6).
Make sure that the straight tube (14) are oriented so
the small hole are in the position shown.
11
10
17
Plastic Cap
(21)
15
14
6
Plastic Cap
(21)
Attach the other three Poles (14,15) in the same way.
See inset drawing.
Insert the Completed Pole(14,15)into the hole of POD-Connector(6).
15
14
6
18
10.
Lay out Top G4 Pole (16), joint each section Connector to a
straight line as shown.
Assemble the remaining Top G4 Pole (16) in the same way.
Spread the Netting (19) on the trampoline bed, insert a Top G4
Pole (16) into the opening of Top Sleeve on the Netting (19).
Insert the other Top G4 Pole (16) into the opposite opening
of Top Sleeve on the Netting (19).
10
Lay out G4 Pole and Joint each section to one straight line.
10.a
(16)
Opening
Netting(19)
11. Joint each end of Top G4 Pole (16) by the clip of connector at
each opening. The Top Sleeve of the Netting (19) become a round
shape.
11
G4
Insert the pole into sleeve of the Netting(19)
Joint the end of each pole by Clip of Connector
G4 G4
Attach the first hanging point at the upper edge of the Netting (19)
with the G4 Pole (16) to the Plastic Cap (21) of Top Pole (15).
Attach a second hanging point directly across the Netting (19)
from the first hanging point.
G4
Top Sleeve
Attach the other two hanging point halfway between the first two
hanging points, so four hanging points are attached as shown.
See insert drawing for attached of G4 Pole (16):
Attached Hanging Point:
G
4
Pole(16)
(21)
Netting
11.a
Hanging Point1
Door of Netting
Hanging Point2
Plastic Cap(21)
Hanging Point4
Netting(19)
Hanging Point3
Door of Netting
19
12. Note: During steps 11 and 12, you will
“sew”the lower edge of the Netting(19)
to the V-rings on the bed using the
Cords(22).
Locate the V-ring closest to the door.
Thread one end of a Cord(22)through
the lower edge of the Netting(19)above
the V-ring and then thread the Cord
through the V-ring. Tie the Netting to
the V-ring, by making a double knot in
the Cord.
13. Thread the Cord(22) through the lower
edge of the Netting(19) halfway between
the first V-ring and the V-ring to the
left, and then thread the Cord through
the V-ring to the left. Repeat this
procedure until the entire Cord is
threaded through the Netting and the
V-rings as shown. Keep the Cord taut.
Tie the end of the Cord to the last V-
ring that it reaches.
Tie a second Cord(not shown)to the last
V-ring reached by the first Cord. Thread
the second Cord through the Netting(19)
and the V-ring as described above. Repeat
this procedure with the remaining Cords
until the last Cord reaches the first
Cord. (Note: The last Cord may overlap
the first Cord.) Make sure that the
Netting is sewn to every V-ring on the
trampoline bed; the Netting below the
door must also be sewn to the V-rings.
12
13
14
22
19
19
22
14. Using the included plastic tie,attach the
Safety Placard(20)to the Netting(19)near
the door as shown.
The trampoline/enclosure is now fully assembled.
Make sure that all parts are securely attached.
Familiarize yourself and all users of the trampoline/enclosure with the safety precautions, use and instructional materials, and care and maintenance instructions in this manual before using.
20
Disassembly
To disassemble the trampoline/enclosure,follow assembly steps 1 through 13 in reverse order.
Do not attempt to disassemble any trampoline frame components before the springs and the bed have been removed.
Use gloves to protect your hands from pinch points during disassembly.
20
CARE AND MAINTENANCE
CARE
Do not allow pets or animals on the trampoline or inside the enclosure, as claws may snag and pull the bed material or damage the frame pad or netting.
REMOVING AND STORING THE TRAMPOLINE/
ENCLOSURE
Make sure that the trampoline/enclosure is dry before
removing and storing it. Use caution while removing
the tubes due to the weight of the tubes.
The trampoline/enclosure is intended to be used by one person at a time weighing 100 kg (220 lbs.) or less.
The user should be either barefoot, wearing socks, or wearing gymnastic shoes.
Street shoes or tennis shoes should not be worn on the trampoline. The user should remove all sharp objects from his or her person that may cause injury or damage to the bed. Heavy, sharp, or pointed hard objects should not contact the bed.
Appropriate shoes should be worn inside the enclosure to reduce wear to the bed.
Once the enclosure is removed from the trampoline,
remove all items from the trampoline bed. Make sure
that the bed is clean and that it has no tears or holes.
Store the trampoline/enclosure in a safe, dry location.
SPECIAL CONSIDERATIONS
High Wind
MAINTENANCE
Your trampoline is manufactured using quality materials and crafted to provide you and your family with many years of enjoyment and exercise. Proper maintenance and care will help to prolong the life of the trampoline and reduce the possibility of injury.
Prolonged exposure to the sun, especially ultraviolet rays, will shorten the life of the trampoline / enclosre fabric. For longer fabric life store the trampoline / enclosure when it is not being used A dry trampoline / enclosure, properly stored, will provide the longest life to the fabric, sewing, and hardware. Remove the enclosure from the trampoline during harsh weather conditions or during long periods of non-use.
The following guidelines should always be observed.
Inspect the trampoline/enclosure before each use, and replace any worn, defective, or missing parts.
The following conditions could represent potential hazards and increase the danger of personal injury:
Stake
It is possible for the trampoline/enclosure be blown about by high wind. If you anticipate high winds, the trampoline/enclosure should be moved to a sheltered location, disassembled, or tied down to the ground with ropes and stakes (not included). At least three ropes and three stakes should be used.
The tops of the stakes should be at ground level so that they will not create a tripping hazard. In addition, the tops of the stakes should be covered, if necessary, so that users will not be injured by falling onto the stakes. Make sure to secure the legs or the bases to the ground, as they can separate from the frame sockets.
• a missing, improperly positioned, or insecurely attached frame pad, netting, enclosure tubes , foam sleeves
• punctures, frays, tears, or holes worn in the bed, frame pad, netting, foam sleeves.
• deterioration in the stitching or fabric of the bed, frame pad, netting
• ruptured or missing springs
• a bent or broken frame, leg, enclosure tubes
• a sagging bed, netting
• sharp protrusions on the frame, suspension system, enclosure tubes
If any of these conditions exists, the trampoline should be disassembled or otherwise protected against use until the condition is remedied.
Moving the Trampoline
If the trampoline/enclosure needs to be moved, it should be moved by two persons, kept horizontal, and lifted slightly. If necessary, the trampoline/enclosure can be disassembled for moving.
To disassemble the trampoline/enclosure, follow the assembly steps in reverse order (see pages 15 to 20).
Do not attempt to disassemble the frame sections, legs, or bases before the bed and springs have been removed.
21
EXPLODED DRAWING AND PART LIST
21
15
19
14
20
23
10
12
20
11
1
20
2
6
8
3
7 4
5
8
9
12
26
17
Description
Key
No.
Qty.
24
Description
13
16
25
Key
No.
Qty.
1
2
4
4
Top Tube(With T-Socket,A Marking)
Top Tube( With Socket, B Marking)
3 4 Top Tube( With Enclosure Socket,
B Marking)
6
7
4 4 Top Tube(With Socket,A Marking)
5 4 T-Connector
4
8
POD-Connector
Socket
8 8 Leg Extension
9 4 Center
10 1 Stitched Bed with V-rings
11 1 Frame Pad
12 72 7“ Length Springs
13 4 Enclosure Socket Cap ( The holes
should be covered when the
enclosure is not in use. )
14
15
4
4
Straight pole
Top Pole (With Plastic Cap)
16 2 G4 Pole
17 8 Foam Sleeve
18* 12 Self-tapping Screw
19 1 Netting with attached Hardware
20
21
1
4
User’s Manual and Safety Placard
(2PCS)
Plastic Cap( This part has been attached
to the top of the Top Pole (16).)
22* 8 Cord
23 1 Spring Pulling Tool
24 1 Shoe Bag
25 4 Foam Sleeve cover
26 8 6.5” Length Yellow Springs
*This part is not illustrated.
Specifications are subject to change without notice.
ORDERING REPLACEMENT PARTS
To order replacement parts, visit our Web site or call our Customer Hot Line (see page 3). To help us assist you, please provide the following information when calling:
• the MODEL of the trampoline/enclosure
• the NAME of the product
• the KEY NUMBER and DESCRIPTION of the part (see the PART LIST above)
• the quantity needed
• the desired method of shipping
22
JP1414C
1
2
5
6
3
4
7
8
9
10
11
12
13
4
4
4
4
4
Part Number
Description
JP1414-TRT
/SS5
JP1414-TRS
/LS5
JP1414-TRP
/SS5
JP1414-TRS
/SS5
Top Rail for T-Connector / Small swedge into Support-Connector 5 hole
(TOP & BOTTOM)
,A Marking.
Top Rail for Support-Connector / Large swedge into POD-Connector 5 hole
(TOP & BOTTOM), B Marking.
Top Rail for POD-Connector / Small swedge into Support-Connector 5 hole
(TOP & BOTTOM) ,B Marking.
Top Rail for Support-Connector / small swedge into T-Connector 5 hole
(TOP & BOTTOM) , A Marking.
JP1414-TC
T-Connector picture
4 JP1414-PODC POD-Connector
8
JP1414-SC Support-Connector
8
JP1414-LS
Leg side
4
JP1414-LC
Leg center
1 BED1480-7
Jumping surface with V-Rings
1 PAD14JP4-10G Frame pad
72
4
SP7
7” Spring
JP1414-POD
CAP
POD-Connector Cap (When enclosure is not in use)
23
JP1414C
16
17
14
15
18
19
20
21
22
23
24
25
26
Part Number
Description
4 JP1414-ESP
Bottom enclosure straight pole
4 JP1414-ECP
Top enclosure curved pole
2
SETG4-14JP4
G4
8
FSBLK44
Foam sleeves
12
HWSTS-S12
Self tapping screws
1
NET14-JP4 Enclosure netting
1
4
JP1414C-
MANUAL
User’s manual
HWEPCAP-
15/14
Enclosure pole cap - 15/14
8 HWROPE-S8 Black Rope Cord
1
1
WHSPT
Spring pulling tool
ACC-SB2P
2 Pocket Shoe bag
4
JP1414-ECS Enclosure foam cover sleeves
8 SP6.5
6.5” spring
Picture
Door of Netting
24
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project