transmitter D122.T

transmitter D122.T
User's manual
Set-point-
transmitter
D122.T
Edition of standards 2010, Software version 1.2.0
D122.T
Manual
Page 2
Table of Contents
1
Operation instruction for Explosion protected device................................................................4
2
Transmitter D122.T..........................................................................................................................5
3
2.1
Short description ........................................................................................................................5
2.2
Features overview .....................................................................................................................5
2.3
Conformity with Standards.........................................................................................................6
Installation and Connection...........................................................................................................6
3.1
D122.T with control panel housing ............................................................................................6
3.1.1
Installation control panel housing .......................................................................................6
3.1.2
Connecting D122.T with control panel housing..................................................................6
3.2
Field housing D122.T.................................................................................................................7
3.2.1
Connecting D122.T with field housing................................................................................7
3.3
Initial operation...........................................................................................................................8
3.3.1
Ex works settings – Device reset .......................................................................................8
4
Operation manual............................................................................................................................9
4.1
Front view and push-keys..........................................................................................................9
4.2
Configuration............................................................................................................................10
4.3
Configuration example.............................................................................................................13
5
Flow charts ....................................................................................................................................16
6
Annex .............................................................................................................................................19
6.1
Specifications...........................................................................................................................19
6.2
Type code ................................................................................................................................19
6.3
Dimensions ..............................................................................................................................20
6.4
Application example: connection plan .....................................................................................21
6.5
Material specification ...............................................................................................................21
6.6
Marking ....................................................................................................................................21
6.7
Transport, Storing, Repairs und Disposal................................................................................22
6.8
Failure messages.....................................................................................................................22
6.9
List of Parameters....................................................................................................................22
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
Manual
Page 3
The symbols WARNING, CAUTION, NOTE
This symbol warns of a serious hazard. Failure to observe this
warning may result in death or the destruction of property.
This symbol warns of a possible failure. Failure to observe this
caution may result in the total failure of the device or the system
or plant to which it is connected.
This symbol highlights important information.
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
1
Manual
Page 4
Operation instruction for Explosion protected device
Application and Standards
This instruction manual applies to explosion-protected control panels of type of protection
types below. This apparatus is only to be used as defined and meets requirements of EN 60
079 particularly EN60 079-14 "electrical apparatus for potentiality explosive atmospheres".
Use this manual in hazardous locations, which are hazardous due to gases and vapours according to the explosion group and temperature class as stipulated on the type label. When
installing and operating the explosion protected distribution and control panels you should observe the respective nationally valid regulations and requirements.
General Instructions
The device has to have a back-up fuse as stipulated. The mains connection must have a sufficient short circuit current to ensure safe breaking of the fuse. To achieve an impeccable and
safety device operation, please take care for adept transportation, storage and mounting, as
well as accurate service and maintenance. Operation of this device should only be implemented by authorised persons and in strict accordance with local safety standards.
The electrical data on the type label and if applicable, the "special conditions" of the test certificate Fehler! Unbekannter Name für Dokument-Eigenschaft.are to be observed.
For outdoor installation it is recommended to protect the explosion protected distribution and
control panel against direct climatic influence, e.g. with a protective roof. The maximum ambient temperature is 40°C, if not stipulated otherwise.
Intrinsically Safe Circuits
Erection instructions in the testing certificates of intrinsically safe apparatus are to be observed. The electrical safety values stipulated on the type label must not be exceeded in the
intrinsically safe circuit. When interconnecting intrinsically safe circuits it is to be tested,
whether a voltage and/or current addition occurs. The intrinsic safety of interconnected circuits
is to be ensured. (EN 60079-14, section 12)
Safety Measures: to read and to comply
Work on electrical installations and apparatus in operation is generally forbidden in
hazardous locations, with the exception of intrinsically safe circuits. In special cases
work can be done on non-intrinsically safe circuits, on the condition that during the
duration of such work no explosive atmosphere exists. Only explosion protected
certified measuring instruments may be used to ensure that the apparatus is voltage-free. Grounding and short-circuiting may only be carried out, if there is no explosion hazard at the grounding or short circuit connection.
Danger of static charge!
Clean only with humid cloth!
Do not open when an explosive dust atmosphere is present!
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
2 Set point transmitter D122.T
2
Transmitter D122.T
2.1
Short description
Page 5
The purpose of the D122.T is to make set-point adjustments, like e.g. temperature, pressure
or revolution, inside the explosion endangered area to e.g. high level control units outside explosion endangered areas, via a 4/20 mA current circuit.
The scale span of the transmitter amounts 2000 digits. An additional power supply is not necessary, because the D122.T is in loop like a transmitter into the circuit of a transmitter power
supply.
The indicated value corresponds with the real measured current in the control circuit - it is not
just a static display. So, the user has control of the transmitted set point. Push and hold the
current control button to indicate the physical current in dimension mA.
The D122.T has a configurable incremental set point- setting. The user sets a new set point
by pressing the arrow buttons to increment or decrement the desired set point. The incremental set point- setting works first with an resolution of 1 digit and furthermore with an adjust
progression – so wide set point- adjustments can be done quickly.
Use an additional D122.A indicator to indicate the actual value of the feedback control system.
Therefore, a hazardous area located simple process visualisation of a feedback control system.
2.2
Features overview
; Ex i- Set-point transmitter D122.T into 4 /20 mA control circuit
• Loop powered - easy use in hazardous area, no additional power supply necessary
• Connecting like common transmitters
; Display
• 41/2-digit 7-Segment display, 2000 digits
• LC-Display 30 mm digit height
• Fast bargraph for trend observation, (41 segments, refresh 4 times per second)
; Housings
• Control panel housing, protection class up to IP 55 (HxWxD) 72x144x80 mm
• Field housing, protection class IP 65 (HxWxD) 133,5x138x64 mm
; Ergonomics
•
•
•
•
•
•
•
•
µ-Processor technology for extensive configuration
Scaled by keyboard and display, without reference current
Separately scaleable bargraph (Zoom)
Incremental set point setting (software version 1.1.0 and later)
Current control button (not available by incremental set point setting)
Keeps the configuration after turn off
Ability to change configuration during operation
Exchangeable dimension signs
; Service
• Customised calibration
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
2.3
2 Set point transmitter D122.T
Page 6
Conformity with Standards
The explosion proof indicators type D122.T meets requirements of listed standards in the attachment
(Declaration of conformity). They were developed, manufactured and tested in accordance with stateof-the-art engineering practice and ISO9001:2008.
3
Installation and Connection
3.1
D122.T with control panel housing
3.1.1 Installation control panel housing
The D122.T.3 is predicated for installation in a control panel.
How to insert
the dimension
symbol
Insert the dimension symbol (icon) before mounting. Do this by first
removing the front frame as shown in the figure at left. Now remove
the front panel from the housing as shown in the figure on the right.
How to fix the
device in the
control panel
Fix the device into the control panel with the intend cramps.
Cut the desired dimension symbol out of the set and pull it into its intended place on the right side of the panel. Make sure that the symbol
is facing the front. Replace the front panel and frame.
3.1.2 Connecting D122.T with control panel housing
Connect the indicator only to intrinsically safe
4..20 mA current circuits.
The terminals of the indicators in the control panel housing are
shown in figure Fehler! Verweisquelle konnte nicht gefunden
werden.. The terminals 5,6 and 7,8 are absent by indicators without
alarm monitoring.
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
3 Installation and Connection
Page 7
Please regard the terminal maximum values of the attached EC- type certificate TÜV 99 ATEX 1488 .
Control panel
enclosure
Terminals
3.2
The terminals of the transmitter in the control panel housing are on the
backside.
Terminal
1
2
Comment
+ terminal 4 ..20 mA control circuit
- terminal 4 ..20 mA control circuit
Field housing D122.T
Choose a solid place to install the transmitter in the field area.
How to insert
the dimension
symbol
First, cut the desired dimension symbol out of the set. Then pull off the
four screws of the cap and remove the cap from the housing.
Now push the prepared dimension symbol into the dimension symbol
slot. Make sure that the symbol is facing the front.
The dimension symbol slot are below the display, on the internal side
of the cap.
Finally replace the cup on the housing.
3.2.1 Connecting D122.T with field housing
Connect the indicator only to intrinsically safe
4..20 mA current circuits.
The terminals of the indicators in the control panel housing are shown
in figure Fehler! Verweisquelle konnte nicht gefunden werden..
The terminals 5,6 and 7,8 are absent by indicators without alarm monitoring.
Please regard the terminal maximum values of the attached EC- type certificate TÜV 99 ATEX 1488 .
Field
housing
Terminals
The terminals of the transmitter with field housing are inside.
Terminal
Comment
1
+ Terminal 4..20 mA control circuit
2
- Terminal 4..20 mA control circuit
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
3.3
3 Installation and Connection
Page 8
Initial operation
After connecting, a display test (all segments of the display are on)
appears immediately during one second. Thereupon the display
shows the software version of the transmitter.
Default
parameters
The following parameters are active ex works:
Scale (figure and bargraph)
• 4 mA measured current -> 4.00
• 20 mA measured current -> 20.00
Set point
• 4 mA measured current -> 4.00
• Direct set point setting
Code words
• CODE1: 0001
• CODE2: 0002
3.3.1 Ex works settings – Device reset
Press the Enter- and Right-button during the start sequence to
reactivate the default parameters. (Hardware-Reset)
A reset activates also the ex works calibration.
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4 Operation manual
4
Operation manual
4.1
Front view and push-keys
Page 9
; Front view
; Keys
On the front side of the transmitter are tree buttons with several function symbols. With these
tree buttons the user can activate each function and enter any parameters for any individual
setting.
Each button is named by its function:
Enter-button
Pressing the enter-button starts the input menu.
In general, the enter-button activates the menu item or accepts the manipulated value of a parameter.
Up-button
Functions of the up-button are:
1. present current value button or increment set point
2. modification of the selected figure
3. pass menu items
Right-button
Functions of the right-button are:
1. change the state to set point edit menu or decrement set point
2. select figures
3. pass menu items
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4.2
4 Operation manual
Page 10
Configuration
It is easy to set the parameters and change the configuration of the transmitter. The inputs
are logical grouped by a menu structure. The flow charts of these menus can be found at
chapter 5.
, Note Flow
charts
SET
) Normal state
The Input-views in the flow diagrams have additional
boxes in their background, because the Input-views may
be changed by pressing any button.
The procedure, to enter a value, is shown in the flow
chart ‘Edit menu’, see Figure 4: Flow chart edit mode
After connecting, the transmitter D122.T starts to initialise its
configuration. The configuration data is stored in an internal
EEPROM due to the previous run. On the first start, the
D122.T transmitter initialises the ex works configuration.
Directly past starting sequence the transmitter begins to
operate. This state is called the ‘normal state’ of the D122.T
and the transmitter is also ready for inputs.
(See also flow diagram in Figure 1)
) Set point
adjusting
It is possible to adjust the set point in two ways:
1. Direct set point setting: the user pushes the rightbutton following the enter-button. The D122.T is then in
the set point edit mode and the user can enter the new
set point by editing the figures of the set point.
2. Incremental set point setting: the transmitter is in
normal state. The user pushes the up-button to increment the set point or he pushes the right-button to decrement the set point .
Configure the way of the set point adjustment in the input
menu of the D122.T (as shown below). The direct set point
setting is configured ex works.
, Tip*
If the incremental set point setting is active – then the present current control as well as the direct set point setting is
not available.
) Present-value
control*
Pushing and holding the up-button (present value control
button) the display shows the present measured value.
(See also flow diagram in Figure 1)
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4 Operation manual
Page 11
) Direct set point
setting*
One touch on the right-button starts the preset menu.
(See also flow diagram in Figure 1: flow chart normal state)
SET
SET
The transmitter screen shows “SET”.
Press the enter-button to see the present preset value.
Press the enter-button a second time, to change the preset
value.
The display switches into the
; Edit mode.
_1234
A blinking segment appears below the sign place. Pressing
the right-button selects the figures and the up-button increments the selected figure. To accept the new preset value,
press the enter-button.
(See also flow diagram in Figure 4)
; Code protection
CodE 2
Before the menu gets to the edit mode the code 2 must be
entered, to prevent a modification by unauthorised persons. Entering a wrong code word stops the limit view
menu immediately.
The default code 2 is [0002].
The interrogation of code 2 can be switched off by modifying the code 2 to [0000]. For this reason the flow diagram
shows the code interrogation in stroked dots. To change the
code you must enter the input menu, as shown below in this
chapter.
; Parameter
entering
(See also flow diagram in Figure 2)
Back in the normal state of the transmitter we start the
) Input menu
CodE 1
by pressing the enter-button.
The configuration of the transmitter is protected against manipulations by unauthorised persons with the code 1. To join the
input menu enter the code 1 .(Default: 0001).
It’s impossible to switch off the code 1 interrogation.
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4 Operation manual
Page 12
After entering the right code word the transmitter proposes to join
the
SCAL
Scale menu. The figure on the left hand appears on the display.
To scale the measured current, the bargraph and to set the
decimal point join the scale menu by confirming with the enterbutton.
(See also flow diagram in Figure 3).
Enter the upper scale point correct figured ‘as big as possible’
(the first figures should not be ‘0’)
In this case you get the maximum precision of the transmitter.
SET
Press the right-button to pass the scale menu and select the
second submenu, the preset menu. To join it, press the enter-button.
(See also flow diagram in Figure 4)
roll
This is the menu item to configure the way of the set point
setting.
Start with pressing the enter-button. Now toggle between
[roll n] (= roll – no i.e. direct set point setting) and [roll y] (=
roll – yes, i.e. incremental set point setting) by pressing any
arrow button.
Confirm the desired configuration by pressing the enterbutton.
CodE 1
The next two following items allow to manipulate the words
for code 1 and code 2. The enter-button confirms the input
and the corresponding code appears in edit mode.
CodE 2
Remember that the code word [0000] will switch off the code
2.
CAL
Finally it’s possible to calibrate the transmitter with the following submenu called calibration menu. Regard, the
transmitter is already calibrated ex-works.
In general, a further calibration is not necessary and
only experienced persons are allowed to calibrate it.
End
Now we reach the end of the input menu. Confirm all settings with the enter-button. The transmitter switches back to
normal state.
If you want to repeat the input menu, press the right-button.
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4 Operation manual
Page 13
If an invalid value is entered for any of the parameters, you
will not be able to quit the input menu. Instead, the menu
program switches automatically into edit mode to the identified invalid value.
4.3
Configuration example
For a successful parameter input, see the following example of a temperature transmitter.
This demonstration is based on the ex works settings (default parameters). If you had already made other settings reset the transmitter, as shown in chapter 3.3, Make a reset to the
device to get back the default parameters.
Situation
• Preset range:
-20,0°C ...+150,0°C
Adjustment:
1] Measure range:
-020,0 °C ... + 150,0°C
for 4 ... 20 mA
2] Bargraph:
-020,0°C ... + 150,0°C
3] Incremental set
point setting
Procedure:
One touch on the enter-button quits the normal state and
starts the input menu.
CodE1
The menu interrogates for code 1.
The default code 1 is [0001].
Enter the right code word using the arrow buttons.
Finally hit the enter-button.
; Scaling display and barograph:
SCAL
dP.Pos
Join the scale menu by pressing the enter-button.
First set the position of the decimal point. The position of
the decimal point will be used for each parameter, like display, barograph and preset value.
Set the decimal position after the third position (counted
from left side), because we will enter [1500] for the high
scale point afterwards.
Choose the enter-button to edit the decimal point position
and push the right-button. Watch the display, the decimal
point shifts right.
Press the enter- button, to quit decimal point setting.
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4 Operation manual
SCA L
Page 14
Now the [scale point low] view appears.
Edit by pressing the enter-button and enter the lower scale
point
[0200] (-20°C) as follows:
_040.0
Press the up- button to select the negative symbol.
- 040.0
Now press the right- button for two times to select the second
figure.
-040.0
Repeat pushing the up-button until ...
...
-020.0
... the figure 2 appears.
confirm the lower scale point by pushing the enter-button, so the
scal point high parameter (SCA H) will be displayed .
SCA H
According above, enter now the figure sequence [1500] to the set
the scal point high to 150°C.
(Confirm with the enter-button).
Enter the upper scale point correct figured ‘as big as possible’
(the first figures should not be ‘0’)
In this case you get the maximum precision of the transmitter.
It is not possible to set a preset range bigger than 2000 digits. The
device refuses a bigger range. But it is possible to place the preset range of 2000 digits in the range of –9999 to +9999 (e.g. 6000
... 8000).
bAr L
Now scale the bargraph. Hit the enter-button.
Enter [-0200] (-20 °C) for the lower bargraph scale point.
Confirm by hitting the enter-button.
bAr H
Enter [1500] (150°C) for the upper bargraph scale point.
Pushing enter-button accepts and quits the scale menu.
Pass the menu point [Set ] by pressing the right-button.
roll
Gönnheimer Elektronic GmbH
Now configure the incremental set point setting. First press the
enter-button. Then press the up-button to select [roll y].
Finally confirm by pushing the enter-button.
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
4 Operation manual
Page 15
We pass simply the following menu items (manipulate code
words and calibrate) using the right-button.
EnD
Gönnheimer Elektronic GmbH
Finally quit the input menu hitting the enter-button.
The transmitter is back in normal state. The changes are immediately active and will still be active after power off (disconnecting
the transmitter).
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
5
5 Flow charts
Page 16
Flow charts
Figure 1: flow chart normal state (by direct set point setting only)
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
5 Flow charts
Page 17
Figure 2: Flow chart input menu
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
SET
edit bargraph
high position
Scale
menu
END
select bargraph
high position
SET
edit bargraph
low position
select bargraph
low position
SET
edit high cale point
(20 mA measure cur.)
Page 18
SET
SET
select
high scale point
SET
edit low scale point
(4 mA measure cur.)
select
low scale point
SET
select decimal
point position
SET
set position
5 Flow charts
Scale
menu
START
SET
SET
D122.T
Figure 3: Flow chart scale menu
edit values enter code
SET
SET
SET
etc.
sign is
selected
second figure
is selected
first figure
is selected
Menu
END
SET
Menu
END
Menu
END
SET
SET
etc.
sign
is modified
second figure
is modified
first figure
is modified
Menu
END
Menu
END
SET
SET
SET
Menu
END
etc.
first figure
is modified
sign
is modified
Menu
END
etc.
second figure
is modified
Menu
END
etc.
Menu
END
etc.
Figure 4: Flow chart edit mode
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
6 Annex
6
Annex
6.1
Specifications
Page 19
D122.T
D122.T.3
D122.T.5 (7)
Display
seven-segment LCD
Digit height
30 mm
Display range
4 1/2 figures, 2000 Digits
Dimension symbols
Selectable by defined symbols
Decimal points
Selectable by keyboard
Bargraph
41 segments, refresh 4 Hz
control circuit
Intrinsically safe control circuit 4 ...20 mA,
Voltage range 8 ..30V; Voltage drop ca. 8V
Current control button
Direct current indication in control circuit
control circuit limits
No-load voltage UI = 65 V, short-circuit current II = 160 mA; PI = 1,6 W
Internal inductance: < 40 μH, Internal capacitance: < 10 nF,
see certificate PTB 99 ATEX 1488
Explosion protection
E Ex ib IIC T6 at ambient temperature 45°C
or E Ex ib IIC T5 at ambient temperature 60°C
Housing
Acc. to control-panel standard DIN
43700
-
Environment Protection
Front panel IP 40 up to IP 55
IP 65
Dimensions HxWxD
[mm]
72 x 144 x 80
133,5 x 138 x 82
Control panel hole
66 x 136,5
Material
glass fibre strengthened Noryl
ABS
Measuring error
0,1% ± 2 digits referring to measure range
Temperature
< 0,01% of measure range / K
coefficient
Ambient
temperature limit
-10°C ...+45°C at temperature class 6 or
-10°C ...+60°C at temperature class 5
devices for -20°C ambient temperature on inquiry
6.2
Type code
Set-point transmitter D122.T .x
Housing:
Control panel housing....................................................................... .3
Field housing ................................................................................... .5
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
6.3
6 Annex
Page 20
Dimensions
Figure 5: Control panel housing, only the dimensions in brackets are valid
Figure 6: Field housing D122.T.5
(total height)
M16 x 1,5
Figure 7: Field housing D122.T.5
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
6.4
6 Annex
Page 21
Application example: connection plan
Figure 8: connection plan
6.5
Material specification
Device type
6.6
Material
manufacturing process
D122.x.0.x.x
Noryl
injection die casting
D122.x.3.x.x
Noryl
injection die casting
D122.x.5.x.x
ABS
injection die casting
D122.x.6.x.x
ABS
injection die casting
D122.x.7.x.x
Aluminum
die-casting
Marking
Marking according to 50014 ff
Marking according to EN 60079 :2010
D122.x.x.x.0
D122.x.x.x.MU
II 2 G; EEx ia IIC T6 bei Ta bis 45°C
II 2 G; EEx ia IIC T5 bei Ta bis 60°C
II 2 G; Ex ia IIC T6 Gb bei Ta bis 45°C
II 2 G; Ex ia IIC T5 Gb bei Ta bis 60°C
D122.x.x.x.BM
II 2 G; EEx ia [ib] IIC T6 bei Ta < 45°C
II 2 G; EEx ia [ib] IIC T5 bei Ta < 60°C
II 2 G; Ex ia [ib] IIC T6 Gb bei Ta < 45°C
II 2 G; Ex ia [ib] IIC T5 Gb bei Ta < 60°C
D122.x.7.x.0
D122.x.7.x.MU
II 2 G; EEx ia IIC T6 bei Ta < 45°C
II 2 G; EEx ia IIC T5 bei Ta < 60°C
II 2 D; Ex IP65 T70°C
II 2 G; Ex ia IIC T6 Gb bei Ta < 45°C
II 2 G; Ex ia IIC T5 Gb bei Ta < 60°C
II 2 D; Ex tb IIIC IP65 T70°C Db
D122.x.7.x.BM
II 2 G; EEx ia [ib] IIC T6 bei Ta < 45°C
II 2 G; EEx ia [ib] IIC T5 bei Ta < 60°C
II 2 D; Ex IP65 T 70°C
II 2 G; Ex ia [ib] IIC T6 Gb bei Ta < 45°C
II 2 G; Ex ia [ib] IIC T5 Gb bei Ta < 60°C
II 2 D; Ex tb IIIC IP65 T70°C Db
0044
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.T
6.7
6 Annex
Page 22
Transport, Storing, Repairs und Disposal
Transport
Vibration-free in origin package, do not pitch, handle carefully
Storing
Store the device dry, inside of the origin package
Disposal
When the explosion proof multipurpose distribution, switching and control
units are eventually disposed of, the national regulations governing the disposal of waste materials in the country concerned must be rigorously observed.
Defective parts may only be replaced by the Manufacturer or by personnel
specially trained and supervised by the Manufacturer. Only genuine spare
parts from the Manufacturer may be fitted.
Repairs
6.8
Failure messages
At startup:
Message
Symptom
Bug-fix
Error 1
Error, general device fault
Turn off an turn on the device, if the fault
remains, send the device back to Gönnheimer
6.9
List of Parameters
The customer is free to use this chart for archiving the parameters of his transmitter D122.T.
Parameter
Description
previous Value
Display
Scale menu
Decimalpoint position
dP.PoS
Low scale point
Display at 4 mA input current
SCAL L
High scale point
Display at 20 mA input current
SCAL H
Bargraph low position
Display of starting bargraph
bAr L
Bargraph high position Display at full bargraph
bAr H
Way of set point setting
direct or
roll n
incremental
roll y
Code 1
Access code to rescale and configure the
transmitter
Code1
Code 2
Access code to set the preset
Code2
Gönnheimer Elektronic GmbH
phone: +49(6321)49919-0, fax: -41
0000
Email: info@goennheimer.de
Non authorized translation
(1)
EC- TYPE- EXAMINATION CERTIFICATE
(Translation)
(2)
Equipment and protective systems intended for use in
potential explosive Atmospheres – Directive 94/9/EC
(3)
EC- type- examination Certificate number
TÜV 99 ATEX 1488
(4)
Equipment:
Digital Indicator Type D122...
(5)
Manufacturer:
Gönnheimer Elektronic GmbH
(6)
Address:
D-Neustadt an der Weinstraße
(7)
This equipment and any acceptable variation thereto are specified in the schedule to
this certificate and the documents therein referred to.
(8)
The TÜV Hannover/Sachen-Anhalt e.V., TÜV CERT-Zertifizierungsstelle, notified body
No. 0032 in accordance with Article 9 of the Council Directive 94/9/EC of March 1994,
certifies that equipment has been found to comply with the Essential Health and
Safety Requirements relating to the design and construction of equipment and
protective systems intended for use potentially explosive atmospheres, given in Annex
II to the Directive.
The examination and test results are recorded in the confidential report No.
99/PX24090
(9)
Compliance with to essential Health and Safety Requirements has been assured by
compliance with:
EN 50 014:1997 EN 50 020:1994 EN 50 028:1988
(10)
If the sign “X” is places after the certificate number, it indicates that the equipment is
subject to special conditions for safe use specified in the schedule to this certificate.
(11)
This EC- type- examination Certificate relates only to the design and construction of
the specified equipment in accordance with Directive 94/9/EC. Further requirements of
this Directive apply to the manufacture and supply of this equipment.
(12)
The marking of the equipment shall include the following:
II 2 (1) G EEx ia IIC T6 bzw. EEx m [ib] IIC T6
TÜV Hannover/Sachen-Anhalt e.V.
TÜV CERT-Zertifizierungstelle
Am TÜV 1
D-30519 Hannover
Hannover, 02.11.1999
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 1 of 8
Non authorized translation
(13)
SCHEDULE
(14)
(15)
EC- TYPE-Examination CERTIFICATE No. TÜV 99 ATEX 1488
Description of equipment
The digital indicator type D122 ... serves as direct indicator of measured values of
intrinsically safe 4 ..20 mA current circuits in explosive endangered areas.
The maximum ambient temperature is 45°C in temperature class T6 and 60°C in the
temperature class T5.
Electrical details
Supply and
signal current
circuit
(Terminal 1,2)
Exclusive connection to a certificated intrinsically safe
current circuit with the following highest values:
Ui = 65 V
Ii = 160 mA
Effective internal inductivity 40 µH
Effective internal capacity
10 nF
Only Type D122.T.x.x.x
Supply and
signal current
circuit
(Terminal 1,2)
Exclusive connection to a certificated intrinsically safe
current circuit with the following highest values:
Ui = 30 V
Ii = 160 mA
Pi = 1,6 W
Effective internal inductivity 40 µH
effective internal capacity
10 nF
Terminals 3,4
Bridget
Only TYP 122.x.x.x.BM with additional protection type moulding and the sign EEx m
[ib] IIC T6 bzw. EEx m [ib] IIC T5
Input current
circuit (wire)
Um = 250 V and to connect to ground
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 2 of 8
Non authorized translation
Schedule EC- Type- Examination Certificate No. TÜV 99 ATEX 1488
Any types
Alarm current
circuits
(Terminal 5,6; 7,8)
Outputs:
Inputs:
Exclusive connection to a certificated intrinsically current
circuit with the following highest values each current circuit:
Ui = 30 V
Ii = 160 mA
Pi = 850 mW
Ui = 30 V
Effective internal inductivity ≤ 40 µH
the effective internal capacity is negligibly small
All current circuits are safe gavanically separated up to a nominal voltage of 90 V to
each other. The input current circuit by the type D122.x.x.x.BM is internally connected
to the supply and signal circuit.
(16)
Report No. 99/PX24090
(17)
Special conditions for safe area
None
(18)
Essential health and safety requirements
No additional
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 3 of 8
Non authorized translation
1. Amendment
to
the Conformity Certificate Nr. TÜV 99 ATEX 1488
Manufacturer:
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
The digital indicator type D122 can also be manufactured according to the examination
protocol, listed in the associated examination certificate.
The changes concern the enlargement around the type D122.x.7.x.x. and the application of
type in explosion areas by dust up to ambient temperatures of 65°C. The marking for it is:
II 2 D IP 65 T70°C
Bases of the standards: EN 50281 1 1:1999
The electric data and all other information are valid consistently for this supplement.
The test documentation is listed in test report Nr. 04YEX551218
TÜV NORD CERT GmbH & Co. KG
Hannover, 17.02.2004
TÜV CERT-Zertifizierungsstelle
Am TÜV 1
0-30519 Hannover
Tel.: 0511 986-1470
Fax: 0511 986-2555
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 4 of 8
Non authorized translation
2. Amendment
to
the Conformity Certificate Nr. TÜV 99 ATEX 1488
Manufacturer:
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
The digital indicator type D122 can also be manufactured according to the examination
protocol, listed in the associated examination certificate. The change concerns the
enlargement around the types D122.PA.7.0.0 and D122.FF.7.0.0 for the binding to
intrinsically safe field busses Profibus PA respectively FF.H1.
The application of the supplemental types can occur in explosion-threatened areas,
Which requires devices of the category 2. By the application in areas of explosion-threatened
by dust, the at most allowed ambient temperature is +65°C.
By the application in areas explosion-threatened by gas is the maximum ambient
temperature depending on the temperature class according to the following table:
Temperature classe
T6
T5
Ta
Up to 45°C
Up to 60°C
Electrical data of the types D122.PA.7.0.0 and D122.FF.7.0.0
Signal and power supply circuit
Ex- protection Intrinsically safe EEx ia IIC
(terminal 1,3 and 2,4)
only to the connection in certified intrinsically
safe circuits. Maximum ratings:
U0 = 30 V
I0 = 660 mA
P0 = 1,6 W
max reactances
L0 = 0 µH
C0 = 0 nF
The electrical data remains unchanged.
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 5 of 8
Non authorized translation
2. Amendment to the Conformity Certificate Nr. TÜV 99 ATEX 1488
The marking of the equipment:
II 2 (1) G EEx ia IIC T6 or T5; resp. II 2 D IP65 T70°C
The marking of the further types remain unchanged.
The digital indicator type D122... according to the EC-type certificate TÜV 99 ATEX 1488
incl. 1. and this 2nd supplement also fulfils the demands of
EN 50 014 :1997 + A1+A2
EN 50 020:2002
EN 50 281-1-1:1998+A1
General directives
Intrinsically safe “i”
Electrical devices with protection by case construction and check
All remaining data remain unchanged for this 2. Amendment.
The test documentation is listed in test report Nr. 04YEX551692
TÜV NORD CERT GmbH & Co. KG
Hannover, 03.11.2004
TÜV CERT-Zertifizierungsstelle
Am TÜV 1
0-30519 Hannover
Tel.: 0511 986-1470
Fax: 0511 986-2555
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 6 of 8
Non authorized translation
3. Amendment
to certification number:
TÜV 99 ATEX 1488
Device:
Manufacturer:
Digital indicator type D122…
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
Germany
8000553381
10.10.2006
Address:
Order Number:
Date of issue:
Changes:
The digital indicator type D122 can also be manufactured according to the examination
protocol, listed in the associated examination certificate. The change concerns the
enlargement around the types D122.PA.7.0.3K and D122.FF.7.0.3K for the binding to
intrinsically safe field busses Profibus PA respectively FF.H1 as a three channel indicator.
The application of the supplemental types can occur in explosion-threatened areas, which
requires devices of the category 2. By the application in areas of explosion-threatened by
dust, the at most allowed ambient temperature is +65°C.
The information to the allowed ambient temperature is valid consistently accordingly of the
second supplement also for the supplemental types.
The electric data of the second supplement are changed as follows or complemented:
Electric data of the types D122. PA.7.0.0, D122.FF 7.0.0, D122. PA.7.0.3K and
D122.FF.7.0.3K:
Signal and power supply circuit
(terminal 1,3 and 2,4)
By the application in by gas explosionthreatened areas in Ex protection
Intrinsically safe EEx ia IIC.
Field device FISCO to the connection with a
device according to the FISCO model or
Only to the connection in certified
intrinsically safe circuits. Maximum ratings:
U0 = 30 V
I0 = 660 mA
max reactances
L0 = 0 µH
C0 = 0 nF
By the application in by dust explosionthreatened areas max. limit input power
P0 = 1,6 W
The electrical data remains unchanged.
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 7 of 8
Non authorized translation
3. Amendment to the Conformity Certificate Nr. TÜV 99 ATEX 1488
The marking of the equipment:
II 2 (1) G EEx ia IIC T6 or T5; resp. II 2 D IP65 T70°C
The marking of the further types remain unchanged.
The digital indicator type D122... according to the EC-type certificate TÜV 99 ATEX 1488
incl. 1. and this 2nd supplement also fulfils the demands of
EN 50 014 :1997 + A1+A2
EN 50 020:2002
EN 50 281-1-1:1998+A1
DIN EN 60079-27:2006
General directives
Intrinsically safe “i”
Electrical devices with protection by case construction and check
Concept for intrinsically safe field bus systems
(FISCO) and concept for non sparking field bus
systems (FNICO)
The test documentation is listed in test report Nr. 06 YEX 553381.
(17)
Special conditions for safe area
None
(18)
Essential health and safety requirements
No additional
TÜV NORD CERT GmbH, Langemarckstraße 20, 45141 Essen, akkreditiert durch die Zentralstelle der Länder für
Sicherheitstechnik (ZLS), Ident. Nr. 0044, Rechtsnachfolger der TÜV NORD CERT GmbH & Co. KG Ident. Nr.
0032
Der Leiter der Zertifizierungstelle
Schwedt
Geschäftsstelle Hannover, Am TÜV 1, 30519 Hannover, Tel.: +49 (0) 511 986-1455, Fax: +49 (0) 511 986-1590
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 8 of 8
EG-Konformitätserklärung
Declaration of conformity / Déclaration de conformité
Communauté Européenne
Anbieter:
Supplier:
Fournisseur
Gönnheimer Elektronic GmbH
Anschrift:
Address:
Adresse:
Gewerbegebiet Nachtweide
Dr.-Julius-Leber-Straße 2
67433 Neustadt/Weinstraße
Produkt:
Product:
Produit:
D122,
Anzeigegerät /Zähler
Das oben beschriebene Produkt erfüllt die Schutzanforderungen der folgenden EG-Richtlinien
/ the product described above complies with the following EG- rules / le produit décrit cidessus accomplit CU- réglementations
2004/108/EG, 93/68/EWG, 94/9/EG
und ist konform mit / and is in conformity with / et est conforme á:
DIN EN 60079-0: 2010, Allgemeine Bestimmungen
DIN EN 60079-11: 2007, Eigensicherheit „i“
DIN EN 60079-18: 2005, Vergusskapselung „m“
DIN EN 61241-1: 2005, Schutz durch Gehäuse "tD"
DIN EN 60079-27: 2006, Feldbussystme FISCO + FNICO
EN 61000-6-4: Fachgrundnorm Störaussendung; Teil 6-4: Industriebereich
EN 61000-6-2: Fachgrundnorm Störfestigkeit; Teil 6-2: Industriebereich
EN 60947-1: Niederspannungs-Schaltgeräte
zusätzliche Angaben / additional information / informations supplémentaires:
Qualitätsmanagement- System nach ISO EN DIN 9001:2008
Anerkanntes Qualitätssicherungssystem nach Richtlinie 94/9/EG
EG- Baumusterprüfbescheinigung / EC- Type certification / Attestation d’examen ce de type
TÜV 99 ATEX 1488
Neustadt, den 11.03.2010
Gönnheimer Elektronic GmbH
EG-Konformitätserklärung; Rev.1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising