PC-586U(PC) Single Board Computer for PICMG User`s Guide

PC-586U(PC)
Single Board Computer for PICMG
User’s Guide
Contents
Copyright
Copyright 1998 CONTEC Co., Ltd. All Rights Reserved No part of this document
may be copied or reproduced in any form by any means without prior written consent
of CONTEC Co., Ltd.
CONTEC Co., Ltd. makes no commitment to update or keep current the information
contained in this document. The information in this document is subject to change
without notice.
All relevant issues have been considered in the preparation of this document. Should
you notice an omission or any questionable item in this document, please feel free to
notify CONTEC Co., Ltd.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any
errors that may appear in this document nor for results obtained by the user as a
result of using this product.
Limited One Year Warranty
CONTEC Single Board Computer are warranted by CONTEC Co., Ltd. to be free
from defects in material and workmanship for up to one year from the date of
purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a
copy of the original invoice and a Return Merchandise Authorization to the
distributor or the CONTEC group office from which it was purchased. This warranty
is not applicable for scratches or normal wear, but only for the electronic circuitry
and original boards. The warranty is not applicable if the device has been tampered
with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the
original invoice is not included, in which case repairs will be considered beyond the
warranty policy.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event
will the warrantor be liable for any incidental or consequential damages due to such
defect or consequences that arise from inexperienced usage, misuse, or malfunction
of this device.
PC-586U(PC) User’s Manual
i
Contents
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the
original invoice. Please obtain a Return Merchandise Authorization Number
(RMA) from our Sales Administration Department before returning any product.
No product will be accepted by CONTEC group without an RMA number.
Acknowledgments
AMD is a registered trademark of Advanced Micro Devices, Inc.
Award is a registered trademark of Award Software International, Inc.
C&T is a trademark of Chips and Technologies, Inc.
Cyrix is a trademark of Cyrix Corporation.
IBM/AT and PS/2 is trademarks of International Business Machines Corporation.
Intel and Pentium are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft Corporation.
All other product names or trademarks are properties of their respective owners.
CAUSION
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer's instructions.
ii
PC-586U(PC) User’s Manual
Contents
Contents
Chapter 1 Introduction............................................. 1
Checklist ...................................................................2
Description ...............................................................2
Features ....................................................................3
Specifications............................................................3
Intelligence ...............................................................5
Board Dimensions and Layout ................................6
Chapter 2 Installations ............................................ 7
CPU Installation.......................................................8
Memory Installation.................................................9
Jumpers on the PC-586U(PC) ...............................10
Connectors on the PC-586U(PC)...........................24
Watchdog Timer Configuration ............................39
Chapter 3 BIOS Configuration ............................. 41
Chapter 4 VGA Driver Installation ...................... 65
Chapter 5 LAN Driver Installation Guide ........... 69
Chapter 6 SCSI Driver Installation Guide ........... 77
Chapter 7 Intel PIIX Bus Master IDE Driver
Installation ........................................... 85
Appendix ................................................................. 89
A. I/O Port Address Map.......................................90
B. Interrupt Request Lines (IRQ) ........................91
PC-586U(PC) User’s Manual
iii
Contents
This page was intentionally left blank.
iv
PC-586U(PC) User’s Manual
Chapter 1 Introduction
1
Introduction
This manual is designed to give you information on the PC-586U(PC) CPU card. It
is divided into the following sections:
Checklist................................................................................... 2
Description ............................................................................... 2
Features .................................................................................... 3
Specifications............................................................................ 3
Intelligence ............................................................................... 5
Board Dimensions and Layout .................................................. 6
The topics covered in this chapter are as follows:
u
Checklist
u
Description
u
Features
u
Specifications
u
Layout of Key Components and Dimensions
PC-586U(PC) User’s Manual
1
Chapter 1 Introduction
Checklist
Please check that your package is complete and contains the items below. If you
discover damaged or missing items, please contact your dealer.
• The PC-586U(PC) Industrial CPU Card
• This User’s Manual
• 1 IDE Ribbon Cable
• 1 Floppy Ribbon Cable
• 1 Key Board Exchange Cable
• 1 Mounting Bracket with 1 Serial Port Ribbon Cable and 1 Parallel Port
Ribbon Cables
• 1 Mounting Bracket with 1 Serial Port Ribbon Cable
• 1 Diskette Containing Intel PCI IDE Driver and Flash Memory Utility
• 1 Diskette Containing System Monitor
• 2 Diskettes Containing C&T 69000 VGA Driver
• 2 Diskettes Containing Realtek RTL8139A LAN Driver
• 4 Diskettes Containing Symbios 53C875E SCSI Drivers (SCSI model only)
• 1 Mounting Bracket with SCSI Ribbon Cable (SCSI model only)
• 1 SCSI Terminator (SCSI model only)
Description
The PC-586U(PC) is a PCI Pentium Industrial CPU card based on Intel’s 430TX
chipset and is fully designed for harsh industrial environment. It features ZIF Socket
7 compatible with various processors from Intel, AMD and Cyrix. This card
accommodates up to 256MB of SDRAM memory and a secondary level 512KB
cache.
The PC-586U(PC) comes with onboard CPU temperature sensor to protect your
processor from overheating. The power management feature provides power savings
by slowing down the CPU clock, turning off the monitor screen and stopping the
HDD spindle motor.
2
PC-586U(PC) User’s Manual
Chapter 1 Introduction
Features
• CPU Speed 90~333MHz, Intel P54C, P55C/MMX, Cyrix 6x86, 6x86L,
6x86MX, AMD K5, K6, K6-2
• Intel 430TX PCIset
• Up to 256MB system memory
• Onboard C&T PCI VGA controller
• Onboard Symbios 53C875E Ultra Wide SCSI controller (SCSI model)
• Onboard Realtek RTL8139A Ethernet controller
• 16 level programmable watchdog timer
• High speed bi-directional SPP/ECP/EPP parallel port
• Hardware Monitoring (Winbond W83781D)
Specifications
• Processor Socket: ZIF Socket 7
• Processor:
Intel Pentium/P55C* 90/100/120/133/150/166/200/233/266
Cyrix 6x86/6x86L P150+/P166+
Cyrix 6x86MX-166/180/200
AMD K5 PR90/PR100/PR133/PR166
AMD K6-166/200/233
AMD K6-2 266/300/333/366/400
• Chipset: Intel 430TX PCIset with built-in PCI EIDE
• Secondary Cache: 512KB P.B. SRAM
• Memory: Up to 256MB SDRAM/EDO DRAM
• Memory Sockets: Two 168-pin DIMM sockets for SDRAMs in 8MB, 16MB,
32MB, 64MB, 128MB and 256MB configurations.
• BIOS: Award BIOS, PnP support
• FLASH EEPROM (256KB) for BIOS update
• ISA Plug and Play (PnP) extension
• Power management
PC-586U(PC) User’s Manual
3
Chapter 1 Introduction
• Super I/O: Winbond 83977TF chipset
• Parallel Port: One high-speed parallel port, SPP/EPP/ECP mode
• Serial Port: Two 16550 UART compatible RS-232C/422/485 ports; Max.
baud rate at 115kbps
• Enhanced IDE: Two Bus Mastering EIDE mode, up to 4 devices, Two EIDE
interfaces for up to four devices, support PIO Mode 3/4 or Ultra DMA/33 IDE
Hard Disk and ATAPI CD-ROM.
• FDD Interface: Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB,
2.88MB, LS-120)
• USB Interface: Two USB pin-header connectors, compliant with USB
Specification Rev. 1.0
• Watchdog Timer: 16-level, programmable
• I/O port 0443H to enable watchdog.
• I/O port 0441H to disable watchdog.
• Time-out timing select 0/2/4/6/8/10/12/14/16/18/20/22/ 24/26/28/30
seconds (+/-20%).
• Green Function: Power management via BIOS, activated through
mouse/keyboard movement
• Keyboard Connector: PC/AT type mini-DIN that supports PC/AT; supports
a 5-pin external keyboard connector
• IrDA Interface: Pin-header connector for the optional IrDA external
connector
• VGA Display:
C&T 69000 VGA chip onboard
SVGA for CRT & Panel
32-bit PCI local bus
VGA BIOS with 256KB flash ROM and system BIOS
15-pin connector
1280 x 1024 (256 colors) resolution on SVGA (2MB memory)
68-pin connector for LCD panel, 1280 x 1024 resolution
LCD panel supports monochrome, color STN, TFT, EL
Simultaneous VGA and panel display
4
PC-586U(PC) User’s Manual
Chapter 1 Introduction
• LAN: Realtek RTL8139A Ethernet controller supporting 10Mb/s and
100Mb/s N-way auto negotiation operation
• SCSI: Symbios 53C875E Ultra Wide SCSI controller for data transfer rate of
up to 40MB/s
• SDD: One socket for M-systems Disk on chip is available . Up to 144Mbyte
• Environmental and Mechanical:
• Power Supply: 5A(typ.) @+5V (MMX-266) , 200mA(typ.) @+12V
• Temperature: 0°C to 60°C
• Humidity: 20% to 90% ( No condensation )
• Suspend dust: Not excessive
• Corrosive gas: Must not be present
• Dimensions: 338mm x 122mm
• Weight: 450g
Intelligence
• CPU Slow Down: When system overheat is detected, CPU slows down to
prevent CPU damage. The CPU speed is restored when temperature falls to a
safe level. System overheat is usually caused by malfunctioning of the CPU or
system fan.
• Temperature Monitoring and Alert: A sensor for the CPU temperature on
the PC-586U(PC) monitors the CPU temperature and alerts the user through
the speaker when temperature exceeds the safe heat level.
PC-586U(PC) User’s Manual
5
Chapter 1 Introduction
Board Dimensions and Layout
6
PC-586U(PC) User’s Manual
Chapter 2 Installations
2
Installations
This chapter provides information on how to use the jumpers and connectors on the
PC-586U(PC) in order to set up a workable system. The topics covered are:
CPU Installation ....................................................................... 8
Memory Installation .................................................................. 9
Jumpers on the PC-586U(PC) ................................................. 10
Connectors on the PC-586U(PC)............................................. 24
Watchdog Timer Configuration............................................... 39
PC-586U(PC) User’s Manual
7
Chapter 2 Installations
CPU Installation
The PC-586U(PC) Industrial CPU Card supports a ZIF processor socket for
Pentium-level processors.
Unlike PGA sockets, ZIF (Zero Insertion Force) sockets come with a lever to secure
the processor. Make sure the notch on the corner of the CPU corresponds with the
notch on the inside of the socket.
After you have installed the processor into the ZIF socket, check if the jumpers for
the CPU type and speed are correct.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
8
PC-586U(PC) User’s Manual
Chapter 2 Installations
Memory Installation
The PC-586U(PC) Industrial CPU Card supports two 168-pin DIMM sockets for a
maximum total memory of 256MB. The DRAMs (3.3Volts) for the DIMM sockets
can be 8MB, 16MB, 32MB, 64MB, 128 and 256MB in EDO and SDRAM types.
When populating the DIMM sockets, either of the DIMM sockets can be populated
first.
(DIMM1)
8MB
16MB
32MB
64MB
128MB
8MB
16MB
32MB
64MB
128MB
16MB
32MB
64MB
128MB
32MB
64MB
128MB
64MB
128MB
128MB
256MB
-----
(DIMM2)
--------------------8MB
8MB
8MB
8MB
8MB
16MB
16MB
16MB
16MB
32MB
32MB
32MB
64MB
64MB
128MB
----256MB
PC-586U(PC) User’s Manual
Total Memory
8MB
16MB
32MB
64MB
128MB
16MB
24MB
40MB
72MB
136MB
32MB
48MB
80MB
144MB
64MB
96MB
160MB
128MB
192MB
256MB
256MB
256MB
9
Chapter 2 Installations
Jumpers on the PC-586U(PC)
The jumpers on the PC-586U(PC) allow you to configure your CPU card according
to the needs of your applications. If you have doubts about the best jumper
configuration for your needs, contact your dealer or sales representative. The
following table lists the connectors on PC-586U(PC) and their respective functions.
Jumper Locations on the PC-586U(PC)................................... 11
S1: Bus Speed / Multiplier Setting .......................................... 12
S3 (1-4), JP7, JP4: CPU Voltage Selector................................ 13
Setting CPU Frequency & CPU Voltage.................................. 15
S2: Display Type Setting......................................................... 18
JP1: LCD Power Setting ......................................................... 20
JP3: SCSI Terminator Setting................................................. 20
JP5: Watchdog Generator Selection ........................................ 20
JP7: CPU VIO Voltage Setting ............................................... 21
JP8: Disk On Chip Setting...................................................... 21
JP9: RS-232C/422/485 (COM2) Selection .............................. 22
JP10: Clear CMOS Content .................................................... 23
J15: External Battery Connector ............................................. 23
The following examples show the conventions used in this section.
Jumper Open
Jumper Closed
Switch 1 and switch 2 are set to OFF.
Switch 3 and switch 4 are set to ON.
10
PC-586U(PC) User’s Manual
PC-586U(PC) User’s Manual
J10
J1
M
M
CPU Socket
J11
I M
D
J2
I M
D
2
1
JP4
JP7
JP10
82439TX
J15
J18
J17
S2
82371
S1
JP1
JP5
J19
S3
69000
JP8
DISK ON CHIP
J13
53C875
SCSI J7
LCD1
FD J4
ID E J3
IDE J6
J20
J16
J14
J12
JP2
J 9
JP6
JP9
BIOS
8139A
JP3
J 8
PRN J5
Chapter 2 Installations
Jumper Locations on the PC-586U(PC)
11
Chapter 2 Installations
S1: Bus Speed / Multiplier Setting
S1(1-4)
Bus Speed
60MHz
on on off off xx xx xx xx
66MHz
off off off off xx xx xx xx
S1(5-7)
Multiplier
S1(5-7)
1.5x/3.5x
xx xx xx xx off off off xx
4x
xx xx xx xx on off on xx
2x/6x
xx xx xx xx on off off xx
4.5x
xx xx xx xx on on on xx
2.5x
xx xx xx xx on on off xx
5x
xx xx xx xx off on on xx
3x
xx xx xx xx off on off xx
12
Multiplier
5.5x
xx xx xx xx off off on xx
PC-586U(PC) User’s Manual
Chapter 2 Installations
S3 (1-4), JP7, JP4: CPU Voltage Selector
For Single Voltage CPU*
Intel P54C, Cyrix 6x86, AMD K5, IDT C6
VIO
VCORE
3.5V
3.5V
S3 (1-4)
on on on on
JP4
OPEN
For Dual Voltage CPU
Intel P55C**, Cyrix 6x86L/MX, AMD K6/K6-2
JP7
VIO VCORE
3.3V
1
2
2
3
1
2
3
1
2
3
(0.35u)
K6-233
OPEN
(0.35u)
3.0V
off on off on
3.3V
OPEN
3.2V
off off on on
3.3V
CPU
WinChip 2-3D
on on on on
3.3V
JP4
3.5V
3
1
S3 (1-4)
OPEN
K6-166/200
2.9V
on off off on
OPEN
6x86MX
WinChip 2-3D
3.3V
1
2
3
1
2
3
2.8V
off off off on
3.3V
OPEN
(0.35u)
P55C
6x86L
2.7V
on on on off
OPEN
** P55C = Pentium MMX
PC-586U(PC) User’s Manual
13
Chapter 2 Installations
For Dual Voltage CPU
Intel P55C, Cyrix 6x86L/MX, AMD K6/K6-2
JP7
VIO VCORE
3.3V
1
2
3
1
2
3
1
2
3
1
2
3
3.3V
3.3V
3.3V
3.3V
1
2
S3 (1-4)
JP4
off on on off
OPEN
on off on off
OPEN
off off on off
OPEN
on on off off
OPEN
CPU
2.6V
2.5V
2.4V
2.3V
K6, K6-2
2.2V
3
off on off off
OPEN
(0.35u)
For Dual Voltage CPU
Intel 266MHz (0.25micron)
JP7
1
14
2
3
VIO
VCORE
2.5V
1.9V
S3 (1-4)
JP4
SHORT
off off on on
PC-586U(PC) User’s Manual
Chapter 2 Installations
Setting CPU Frequency & CPU Voltage
For Intel Pentium CPU
CPU
S3 (1-4)
S1 (1-8)
on on on on
on on off off off off off off
on on on on
off off off off off off off off
on on on on
on on off off on off off off
on on on on
off off off off on off off off
off off off on
on on off off on on off off
on on on on
off off off off on on off off
off off off on
off off off off on on off off
on on on on
off off off off off on off off
off off off on
off off off off off on off off
off off off on
off off off off off off off on
JP7
JP4
P54C-90
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
P54C-100
P54C-120
P54C-133
P54C-150
P54C-166
P55C-166
P54C-200
P55C-200
P55C-233
PC-586U(PC) User’s Manual
15
Chapter 2 Installations
For AMD K5/K6/K6-2 CPU
CPU
S3 (1-4)
S1 (1-8)
on on on on
off off off off off off off off
on on on on
off off off off on off off off
on on on on
on on off off on on off off
on off off on
off off off off off on off off
off off on on
off off off off off off off off
off on off off
off off off off on off on off
off on off off
off off off off on on on off
off on off off
off off off off off on on off
off on off off
off off off off off off on off
off on off off
off off off off on off off off
K5-PR100
(100MHz)
K5-PR133
(133MHz)
K5-PR166
(116.7MHz)
(117.K6/166)
JP7
JP4
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
K6/200
K6/233
K6/266
K6-2/266
K6/300
K6-2/300
K6/333
K6-2/333
366MHz
400MHz
16
PC-586U(PC) User’s Manual
Chapter 2 Installations
For Cyrix 6x86 and IDT C6 CPU
CPU
S3 (1-4)
S1 (1-8)
off off off on
on on off off on on off off
off off off on
off off off off on off off off
on off off on
on on off off on on off off
on off off on
on on off off on on off off
on off off on
off off off off off on off off
on off off on
off off off off off off off off
on on on on
on on off off off on off off
on on on on
off off off off off on off off
6x86(L)-P150+
(120MHz)
6x86(L)-P166+
(133MHz)
6x86MXPR166
6x86MXPR200
6x86MXPR233
6x86MXPR300
IDT
C6-180
IDT
C6-200
JP7
JP4
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
1
2
3
OPEN
For Intel 55C (0.25u) 266MHz
CPU
S3 (1-4)
S1 (1-8)
off off on on
off off off off on on off off
JP7
JP4
P55C-266MHz
1
PC-586U(PC) User’s Manual
2
3
SHORT
17
Chapter 2 Installations
S2: Display Type Setting
The PC-586U(PC) supports several resolution LCD displays. Use S2 switch to select
display type.
S2(1-4)
LCD Type
Resolution
CONTEC
Products
Reserved
---
---
STN
1024 x 768
XGA
---
Reserved
---
---
TFT
640 x 480
---
Reserved
---
---
STN
640 x 480
---
Reserved
---
---
TFT
1024 x 768
XGA
IPC-DT/H40X(PC)T
on on on on
on on on off
on on off on
on on off off
on off on on
on off on off
on off off on
on off off off
18
PC-586U(PC) User’s Manual
Chapter 2 Installations
S2(1-4)
LCD Type
Resolution
CONTEC
Products
Reserved
---
---
TFT
1280 x 1024
SXGA
---
CRT only
VGA
SVGA
XGA
SXGA
---
TFT
640 x 480
IPC-DT/M30(PC)T
IPC-DT/S35(PC)
IPC-DT/S35(PC)T
Reserved
---
---
STN
800 x 600
IPC-DS/L30S(PC)T
IPC-DS/L400(PC)T
IPC-DS/L400(PC)
Reserved
---
---
800 x 600
IPC-DT/L30S(PC)T
IPC-DT/L400(PC)T
IPC-DT/L400(PC)
IPC-DT/L40S(PC)T
off on on on
off on on off
off on off on
off on off off
off off on on
off off on off
off off off on
TFT
off off off off
PC-586U(PC) User’s Manual
19
Chapter 2 Installations
JP1: LCD Power Setting
The PC-586U(PC) XGA interface supports 5V and 3.3V LCD displays. Use JP1 to
change between 5V and 3.3V panel video signal level.
JP1
1
2
1
Setting
Function
Pin 1-2
Short/Closed
3.3V
Pin 2-3
Short/Closed
5V
3
2
3
JP3: SCSI Terminator Setting
Use JP3, a 2-pin header, to enable or disable the terminator of the Ultra Wide SCSI
on board.
JP3
Setting
Function
Short/Closed
Disabled
Open
Enabled
JP5: Watchdog Generator Selection
JP5
1
1
20
2
2
Setting
Function
Pin 1-2
Short/Closed
NMI
Pin 2-3
Short/Closed
Reset
Normal Operation
3
3
PC-586U(PC) User’s Manual
Chapter 2 Installations
JP7: CPU VIO Voltage Setting
JP7
1
1
2
2
Setting
Function
Pin 1-2
Short/Closed
2.5V
Pin 2-3
Short/Closed
3.3V
3
3
JP8: Disk On Chip Setting
JP8
1
1
2
2
Setting
Function
Pin 1-2
Short/Closed
D0000-D7FFF
Pin 2-3
Short/Closed
D8000-DFFFF
(Default)
3
3
PC-586U(PC) User’s Manual
21
Chapter 2 Installations
JP9: RS-232C/422/485 (COM2) Selection
COM2 is selectable for RS-232C, RS-422 and RS-485.
The following table describes the jumper settings of this connector.
COM2
Function
Jumper
Setting
(Pin closed)
Jumper
Illustration
RS-232C
All
Jumpers
Open
1
3
5
7
9
11
13
15
17
19
21
23
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
JP9
22
2
4
6
8
10
12
14
16
18
20
22
24
RS-422
RS-485
1-2
3-4
5-6
7-8
11-12
15-16
17-18
19-20
23-24
1-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
21-22
1
3
5
7
9
11
13
15
17
19
21
23
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
JP9
2
4
6
8
10
12
14
16
18
20
22
24
1
3
5
7
9
11
13
15
17
19
21
23
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
4
6
8
10
12
14
16
18
20
22
24
JP9
PC-586U(PC) User’s Manual
Chapter 2 Installations
JP10: Clear CMOS Content
JP10
Setting
Function
Pin 2-3
Short/Closed Clear CMOS Content
1
2
3
Pin 1-2
Short/Closed
1
2
Normal Operation
(Default)
3
J15: External Battery Connector
This 4-pin connector allows the user to connect an external battery to maintain the
information stored in the CMOS RAM in case the built-in battery malfunctions. The
default is set to Internal Battery with a jumper connecting pin 1 and pin 2.
1
4
Internal Battery
1
4
J15 Pin #
1
2
3
4
Signal Name
Ground
Internal Battery GND
N.C.
External Battery Vcc
External
Battery
PC-586U(PC) User’s Manual
23
Chapter 2 Installations
Connectors on the PC-586U(PC)
The connectors on the PC-586U(PC) allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists
the connectors on PC-586U(PC) and their respective functions.
Connector Locations on the PC-586U(PC) .............................. 25
J1: Front Bezel Connector....................................................... 26
J2: Power Connector ............................................................... 28
JP2: IrDA Connector .............................................................. 28
J3, J6: EIDE Connectors......................................................... 29
J4: Floppy Drive Connector .................................................... 30
J5: Parallel Port Connector ..................................................... 30
J7: Ultra Wide SCSI Connector .............................................. 31
J8: COM1 Serial Port.............................................................. 32
J9: COM2 Serial Port.............................................................. 32
J10: External Keyboard Connector.......................................... 33
J11: CPU Fan Power Connector .............................................. 33
J12: RJ45 Connector ............................................................... 33
J13: External ATX Power Connector ...................................... 33
J14: PS/2 Mouse Connector .................................................... 35
JP6: External PS/2 Mouse Connector ...................................... 35
J16: VGA CRT Connector ...................................................... 35
LCD1: LCD Panel Connector ................................................. 36
J17, J18: USB Connectors....................................................... 37
J19: Chassis Fan Power Connector.......................................... 37
J20: PS/2 Keyboard Connector................................................ 37
LED1: SCSI LED ................................................................... 38
LED2, LED3: LAN Activity LED........................................... 38
24
PC-586U(PC) User’s Manual
PC-586U(PC) User’s Manual
J10
J1
M
M
CPU Socket
J11
J2
I M
I M
D
D
1
2
JP4
JP7
JP10
82439TX
J15
J18
J19
S3
69000
LCD1
JP5
DISK ON CHIP
J13 JP8
53C875
SCSI J7
J17
S2
82371
S1
JP1
FD J4
IDE J3
IDE J6
J20
J16
J14
J12
JP2
J 9
JP6
JP9
BIOS
8139A
JP3
J 8
PRN J5
Chapter 2 Installations
Connector Locations on the PC-586U(PC)
25
Chapter 2 Installations
J1: Front Bezel Connector
The front bezel of the case has a control panel providing light indication of the
computer activities and switches to change the computer status. J1 is a 20-pin header
that provides interfaces for the following functions.
Hard Disk Drive LED
Reset Switch
Turbo LED Connector
Green Function
ATX Power On Switch
Power LED and Keylock
Speaker
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio tone
generation. An 8-ohm speaker is recommended.
J1 Pin #
Signal Name
1
Speaker out
2
N.C.
3
Ground
4
+5V
ATX Power On Switch: Pins 6 and 16
This is an “ATX Power Supply On/Off Switch” that is connected to the
power switch on the case.
J1 Pin #
6
16
Signal Name
Ground
Switch
Green Function: Pins 7 and 17
This connector is for the “Green Switch” on the control panel, which,
when pressed, will force the motherboard immediately into the power
saving (sleep) mode.
J1 Pin #
7
17
26
Signal Name
Ground
Sleep
PC-586U(PC) User’s Manual
Chapter 2 Installations
Power LED and Keylock: Pins 11 - 15
The power LED indicates the status of the main power switch. The
keylock switch, when closed, will disable the keyboard function.
J1 Pin #
Signal Name
11
Power LED
12
N.C.
13
Ground
14
Keylock
15
Ground
Turbo LED Connector: Pins 8 and 18
There is the no turbo/deturbo function on the CPU card. The Turbo LED
on the control panel will always be on when attached to this connector.
J1 Pin #
Signal Name
8
5V
18
Ground
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without turning the
main power switch off and then on. Orientation is not required when
making a connection to this header.
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on control panel.
This LED will flash when the HDD is being accessed.
J1 Pin #
Signal Name
10
HDD LED
20
5V
PC-586U(PC) User’s Manual
27
Chapter 2 Installations
J2: Power Connector
When using an AT compatible power supply, plug the power supply connectors into
J2. Make sure the power supply connectors are connected in the right orientation.
See the pin assignments below.
Pin #
6
1
1
2
3
Signal
Name
Power Good
+5V
+12V
Pin #
4
5
6
Signal
Name
-12V
Ground
Ground
JP2: IrDA Connector
This connector is used for an IrDA connector for wireless communication.
JP2 Pin #
Signal Name
1
+5V
2
N.C.
3
Ir RX
JP2
4
Ground
5
Ir TX
28
PC-586U(PC) User’s Manual
Chapter 2 Installations
J3, J6: EIDE Connectors
J3 is the primary IDE connector and J6 is the secondary IDE connector.
J3
J6
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ
Host IOW
Host IOR
IOCHRDY
DACK
IRQ
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
N.C.
Ground
Ground
Ground
Host ALE
Ground
N.C.
N.C.
Address 2
Chip select 1
Ground
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ
Host IOW
Host IOR
IOCHRDY
DACK
IRQ
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
N.C.
Ground
Ground
Ground
Host ALE
Ground
N.C.
N.C.
Address 2
Chip select 1
Ground
PC-586U(PC) User’s Manual
29
Chapter 2 Installations
J4: Floppy Drive Connector
J4
Signal Name
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
Signal Name
RM/LC
N.C.
N.C.
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Step
Write data
Write gate
Track 00
Write protect
Read data
Side 1 select
Diskette change
J5: Parallel Port Connector
The following table describes the pin out assignments of this connector.
J5
30
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
N/A
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
PC-586U(PC) User’s Manual
Chapter 2 Installations
J7: Ultra Wide SCSI Connector
The table below shows the pin-out assignments of this 68-pin connector.
J7
Signal Name
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
LVTRMPWR
LVTRMPWR
N.C.
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
PC-586U(PC) User’s Manual
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Pin #
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Signal Name
SEDAT12
SEDAT13
SEDAT14
SEDAT15
SEDPH
SEDAT0
SEDAT1
SEDAT2
SEDAT3
SEDAT4
SEDAT5
SEDAT6
SEDAT7
SEDPL
GROUND
SEWIN#
LVTRMPWR
LVTRMPWR
N.C.
GROUND
SEATN
GROUND
SEBSY
SEACK
SERST
SEMSG
SESEL
SECD
SEREQ
SEIO
SEDAT8
SEDAT9
SEDAT10
SEDAT11
31
Chapter 2 Installations
J8: COM1 Serial Port
J8, a 10-pin header, is an onboard serial ports of the PC-586U(PC)The following
table shows the pin assignments of this connector.
Pin #
1
2
3
4
5
6
7
8
9
J8
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
Ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
J9: COM2 Serial Port
J9, a 10-pin header connector , is the onboard COM2 serial port of the PC586U(PC). The following table shows the pin assignments of this connectors.
Pin #
.
J9
32
1
2
3
4
5
6
7
8
9
10
RS-232C
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
N.C.
Signal Name
R2-422
TXTX+
RX+
RXGND
RTSRTS+
CTS+
CTSN.C.
RS-485
DATADATA+
N.C.
N.C.
GND
N.C.
N.C.
N.C.
N.C.
N.C.
PC-586U(PC) User’s Manual
Chapter 2 Installations
J10: External Keyboard Connector
J10 Pin #
1
2
3
4
5
1
5
J10
Signal Name
Keyboard clock
Keyboard data
N.C.
Ground
Vcc
J11: CPU Fan Power Connector
J11 is a 3-pin header for the CPU fan power connector. The fan must be a 12V fan.
Pin # Signal Name
3
2
1
2
3
1
Fan sensor
+12V
Ground
J12: RJ45 Connector
This connector is for the 10/100Mbps Ethernet capability of the CPU card. The
figure below shows the pin out assignments of this connector and its corresponding
input jack.
TD+(pin#1)
TD-(pin#2)
RD+(pin#3)
RD-(pin#6)
J12
J13: External ATX Power Connector
1
6
J13
J13 Pin #
1
2
3
4
5
6
PC-586U(PC) User’s Manual
Signal Name
N.C.
Ground
N.C.
Ground
PS-ON (soft on/off)
5V SB (standby +5V)
33
Chapter 2 Installations
34
PC-586U(PC) User’s Manual
Chapter 2 Installations
J14: PS/2 Mouse Connector
J14 Pin #
1
2
3
4
5
6
J14
Signal Name
Mouse data
N.C.
Ground
5V
Mouse clock
N.C.
JP6: External PS/2 Mouse Connector
JP6 Pin #
1
2
3
4
5
JP6
Signal Name
Mouse data
N.C.
Ground
5V
Mouse clock
J16: VGA CRT Connector
J16 is a 15-pin VGA CRT connector. The pin assignments are as follows:
J16
PC-586U(PC) User’s Manual
Signal Name
Red
Blue
GND
GND
N.C.
N.C.
HSYNC
N.C.
Pin
1
3
5
7
9
11
13
15
Pin
2
4
6
8
10
12
14
Signal Name
Green
N.C.
GND
GND
GND
N.C.
VSYNC
35
Chapter 2 Installations
LCD1: LCD Panel Connector
LCD1 is a 68-pin (dual in line header) for flat panel LCD displays. The following
shows the pin assignments of this connector.
68
67
1
2
LCD1
36
Signal
Name
12V
GND
5V/3.3V
5V/3.3V
PD0
PD2
PD4
GND
PD6
PD8
PD10
GND
PD12
PD14
PD16
GND
PD18
PD20
PD22
GND
PD24
PD26
PD28
GND
PD30
PD32
PD34
GND
GND
GND
GND
GND
GND
ENAVDD
Pin #
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
Signal
Name
12V
GND
5V/3.3V
5V/3.3V
PD1
PD3
PD5
GND
PD7
PD9
PD11
GND
PD13
PD15
PD17
GND
PD19
PD21
PD23
GND
PD25
PD27
PD29
GND
PD31
PD33
PD35
SHFCLK
LP
FLM
M
ASCLK
ENABKL
ENAVEE
PC-586U(PC) User’s Manual
Chapter 2 Installations
J17, J18: USB Connectors
J17 and J18 are USB connectors that supports up to 127 USB devices. The following
table shows the pin outs of these connectors.
J18
1
3
5
7
9
J18
Pin #
1
3
5
7
9
J17
2
4
6
8
10
Signal
Name
Vcc
USBUSB+
Ground
Ground
J17
Pin #
2
4
6
8
10
Signal
Name
Vcc
USBUSB+
Ground
N.C.
J19: Chassis Fan Power Connector
J19 is a 3-pin header for the chassis fan power connector. The fan must be a 12V fan.
Pin # Signal Name
3
2
1
2
3
1
Fan sensor
+12V
Ground
J20: PS/2 Keyboard Connector
J20
PC-586U(PC) User’s Manual
J20 Pin #
1
2
3
4
5
6
Signal Name
Keyboard data
N.C.
Ground
5V
Keyboard clock
N.C.
37
Chapter 2 Installations
LED1: SCSI LED
LED1 indicates any activity on the SCSI interface.
LED2, LED3: LAN Activity LED
LED2 and LED3 are light indicators for Link and Data Transfer Activity
respectively for the onboard LAN function.
38
PC-586U(PC) User’s Manual
Chapter 2 Installations
Watchdog Timer Configuration
The function of the watchdog timer is to reset the system automatically and is
defined at I/O port 0443H. To enable the watchdog timer and allow the system to
reset, write I/O port 0443H. To disable the timer, write I/O port 0441H for the system
to stop the watchdog function. The timer has a tolerance of 20% for its intervals.
The following describes how the timer should be programmed.
Enabling Watchdog:
MOV AX, 000FH (Choose the values from 0 to F)
MOV DX, 0443H
OUT DX, AX
Disabling Watchdog
MOV AX, 000FH (Any value is fine.)
MOV DX, 0441H
OUT DX, AX
WATCHDOG TIMER CONTROL TABLE
Level
1
2
3
4
5
6
7
8
Value
F
E
D
C
B
A
9
8
Time/sec
0
2
4
6
8
10
12
14
PC-586U(PC) User’s Manual
Level
9
10
11
12
13
14
15
16
Value
7
6
5
4
3
2
1
0
Time/sec
16
18
20
22
24
26
28
30
39
Chapter 3 BIOS Configuration
3
BIOS Configuration
This chapter describes the different settings available in the Award BIOS that comes
with the PC-586U(PC) CPU card. The topics covered in this chapter are as follows:
BIOS Introduction .................................................................. 44
BIOS Setup............................................................................. 44
Standard CMOS Setup............................................................ 46
Date ............................................................................. 46
Time............................................................................. 47
Primary HDDs / Secondary HDDs ................................ 47
Drive A / Drive B......................................................... 48
Floppy 3 Mode Support ................................................ 48
Video ........................................................................... 48
Halt On ........................................................................ 48
BIOS Features Setup............................................................... 49
Virus Warning ............................................................. 49
CPU Internal Cache / External Cache........................... 49
Quick Power On Self Test............................................. 49
Boot Sequence .............................................................. 50
Swap Floppy Drive ....................................................... 50
Boot Up Floppy Seek .................................................... 50
Boot Up NumLock Status ............................................. 50
Security Option ............................................................ 50
PCI/VGA Palette Snoop ............................................... 50
OS Select for DRAM > 64MB ...................................... 51
Video BIOS Shadow..................................................... 51
C8000 - CBFFF Shadow/DC000 - DFFFF Shadow ....... 51
PC-586U(PC) User’s Manual
41
Chapter 3 BIOS Configuration
Chipset Features Setup ........................................................... 52
DRAM Timing............................................................. 52
System BIOS Cacheable............................................... 52
Video BIOS Cacheable................................................. 52
8 Bit I/O Recovery Time............................................... 52
16 Bit I/O Recovery Time............................................. 52
Memory Hole at 15M-16M........................................... 53
PCI 2.1 Compliance ..................................................... 53
CPU Warning Temperature.......................................... 53
Temperature/Fan Speeds/Voltages................................ 53
Power Management Setup ...................................................... 54
Power Management...................................................... 54
PM Control by APM .................................................... 54
Video Off Method ........................................................ 54
Video Off After ............................................................ 55
Doze Mode................................................................... 55
Standby Mode .............................................................. 55
Suspend Mode.............................................................. 55
HDD Power Down........................................................ 55
Soft-Off by PWR-BTTN............................................... 55
Resume by Alarm......................................................... 55
PWR On by Modem/LAN ............................................ 55
Reload Global Timer Events......................................... 56
PNP/PCI Configuration .......................................................... 57
PNP OS Installed ......................................................... 57
Resources Controlled by ............................................... 57
Reset Configuration Data ............................................. 57
IRQ, DMA assigned to................................................. 57
Used MEM base addr ................................................... 58
Load BIOS Defaults ............................................................... 59
Load Setup Defaults ............................................................... 59
Integrated Peripherals ............................................................ 60
IDE HDD Block Mode ................................................. 60
IDE Primary Master/Slave PIO
And Secondary Master/Slave PIO.......................... 60
IDE Primary Master/Slave UDMA
And Secondary Master/Slave UDMA .................... 60
On-Chip Primary/Secondary PCI IDE .......................... 61
USB Keyboard Support ................................................ 61
Onboard FDD Controller.............................................. 61
Onboard Serial/Parallel Port......................................... 61
UART Mode Select ...................................................... 61
42
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
Onboard Parallel Mode................................................. 61
Supervisor / User Password..................................................... 62
IDE HDD Auto Detection ....................................................... 63
Save & Exit Setup .................................................................. 64
Exit Without Saving ............................................................... 64
PC-586U(PC) User’s Manual
43
Chapter 3 BIOS Configuration
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your computer system’s
ROM supports Intel/Cyrix/AMD processors in a standard IBM-AT compatible I/O
system. The BIOS provides critical low-level support for standard devices such as
disk drives, serial and parallel ports. It also adds virus and password protection as
well as special support for detailed fine-tuning of the chipset controlling the entire
system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the system
configurations and settings. The BIOS ROM of the system stores the Setup utility.
When you turn on the computer, the Award BIOS is immediately activated. Pressing
the <Del> key immediately allows you to enter the Setup utility. If you are a little bit
late pressing the <Del> key, POST(Power On Self Test) will continue with its test
routines, thus preventing you from invoking the Setup. If you still wish to enter
Setup, restart the system by pressing the ”Reset” button or simultaneously pressing
the <Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the system Off
and back On again. The following message will appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to select, the
<PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on the screen.
The Main Menu allows you to select from various setup functions and exit choices.
44
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Time, Date, Hard Disk Type
The section below the setup items of the Main Menu displays the control keys for this
menu. Another section at the bottom of the Main Menu just below the control keys
section displays information on the currently highlighted item in the list.
NOTE: After making and saving system changes with Setup, you find
that your computer cannot boot, the Award BIOS supports an
override to the CMOS settings that resets your system to its
default.
We strongly recommend that you avoid making any changes to
the chipset defaults. These defaults have been carefully chosen
by both Award and your system manufacturer to provide the
absolute maximum performance and reliability.
PC-586U(PC) User’s Manual
45
Chapter 3 BIOS Configuration
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic hardware
configurations in your computer system and set the system clock and error handling.
If the Industrial CPU Card is already installed in a working system, you will not need
to select this option. You will need to run the Standard CMOS option, however, if
you change your system hardware configurations, the onboard battery fails, or the
configuration stored in the CMOS memory was lost or damaged.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Mon, Aug 19 1996
Time (hh:mm:ss) :
00 : 00 : 00
HARD DISKS
TYPE
SIZE
CYLS
HEAD
PRECOMP
LANDZ
SECTOR
MODE
Primary Master
Primary Slave
Secondary Master
Secondary Slave
Auto
None
None
None
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Auto
-------------
Drive A
: 1.44M, 3.5in
Drive B
: None
Floppy 3 Mode Support
: Disabled
Video
: EGA / VGA
Halt On
: All Errors
ESC : Quit
F1 : Help
Base Memory
:
640K
Extended Memory
:
15360K
Other Memory
:
384K
Total Memory
:
16384K
á â à ß : Select
Item
(Shift) F2 : Change Color
PU / PD / + / - : Modify
At the bottom of the menu are the control keys for use on this menu. If you need any
help in each item field, you can press the <F1> key. It will display the relevant
information to help you. The memory display at the lower right-hand side of the
menu is read-only. It will adjust automatically according to the memory changed.
The following describes each item of this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
Sun to Sat
1 to 12
1 to 31
1994 to 2097
To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys
to set the current time.
46
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/- keys
to set the current time.
Primary HDDs / Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary channels for
connecting up to four IDE hard disks or other IDE devices. Each channel can
support up to two hard disks; the first is the “Master” and the second is the “Slave”.
To enter the specifications for a hard disk drive, you must select first a “Type”. There
are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS. Type
1 to 45 are predefined. Type “User” is user-definable. For the Primary Master/Slave
as well as Secondary Master/Slave, you can select “Auto” under the TYPE and
MODE fields. This will enable auto detection of your IDE drives and CD-ROM drive
during POST.
Press <PgUp>/<PgDn> to select a numbered hard disk type or type the number and
press the <Enter> key. The hard disk will not work properly if you enter incorrect
information for this field. If your hard disk drive type is not matched or listed, you
can use Type User to define your own drive type manually. If you select Type User,
related information is asked to be entered to the following items.
CYLS :
Number of cylinders
HEAD :
Number of read/write heads
PRECOMP : Write precompensation
LANDZ :
Landing zone
SECTOR :
Number of sectors
SIZE :
Automatically adjust according to the configuration
MODE (for IDE HDD only) : Auto
Normal (HD < 528MB)
Large (for MS-DOS only)
LBA (HD > 528MB and supports Logical
Block Addressing)
NOTE: The specifications of your drive must match with the drive table. If your
hard disk drive type is not matched or listed, you can use Type User to
define your own drive type manually.
PC-586U(PC) User’s Manual
47
Chapter 3 BIOS Configuration
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has been
installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
Floppy 3 Mode Support
This is the Japanese standard floppy drive. The standard stores 1.2MB in a 3.5-inch
diskette. You have four options to choose:
Disabled
No 3 mode floppy drive installed. (default)
Drive A
Installed 3 mode drive at drive A.
Drive B
Installed 3 mode drive at drive B.
Both
Installed 3 mode drive at drive A and B.
Video
This field selects the type of video display card installed in your system. You can
choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters.(default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA, includes high resolution
monochrome adapters.
Halt On
This field determines whether the system will halt if an error is detected during
power up.
No errors
The system boot will not be halted for any error
that
may be detected. (default)
All errors
Whenever the BIOS detects a non-fatal error,
the system will be halted and you will be
prompted.
All, But Keyboard The system boot will not be halted for a keyboard error; it
will stop for all other errors.
All, But Diskette
The system boot will not be halted for a disk error; it will
stop for all other errors.
All, But Disk/Key The system boot will not be halted for a keyboard or disk
error; it will stop for all other errors.
48
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
BIOS Features Setup
This section allows you to configure and improve your system and allows you to set
up some system features according to your preference.
ROM / PCI ISA BIOS
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning
: Disabled
Video BIOS Shadow
: Enabled
CPU Internal Cache
External Cache
Quick Power On Self Test
Boot Sequence
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up Numlock Status
: Enabled
: Enabled
: Disabled
: A, C, SCSI
: Disabled
: Enabled
: On
C8000-CBFFF Shadow
CC000-CFFFF Shadow
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFFF Shadow
: Disabled
: Disabled
: Disabled
: Disabled
: Disabled
: Disabled
Security Option
: Setup
PCI /VGA Palette Snoop
: Disabled
OS Select For DRAM>64MB
: Non-OS2
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Virus Warning
This item protects the boot sector and partition table of your hard disk against
accidental modifications. If an attempt is made, the BIOS will halt the system and
display a warning message. If this occurs, you can either allow the operation to
continue or run an anti-virus program to locate and remove the problem.
NOTE: Many disk diagnostic programs which attempt to access the boot sector
table can cause the virus warning. If you will run such a program, disable
the Virus Warning feature.
CPU Internal Cache / External Cache
These items allow you to enable (speed up memory access) or disable the cache
function. By default, these items are Enabled.
Quick Power On Self Test
This choice speeds up the Power On Self Test (POST) after you power up the system.
If it is set to Enabled, BIOS will skip some items. By default, this choice is Enabled.
PC-586U(PC) User’s Manual
49
Chapter 3 BIOS Configuration
Boot Sequence
This field determines the drive that the system searches first for an operating system.
The options are :
A, C, SCSI
D, A, SCSI
SCSI, C, A
C, A, SCSI
E, A, SCSI
C only
C, CDROM, A
F, A, SCSI
LS120, C
CDROM, C, A
SCSI, A, C
The default value is A, C, SCSI.
Swap Floppy Drive
This item allows you to determine whether to enable the swap Floppy Drive or not.
When enabled, the BIOS swaps floppy drive assignments so that Drive A becomes
Drive B, and Drive B becomes Drive A. By default, this field is set to Disabled.
Boot Up Floppy Seek
When enabled, the BIOS will seek whether or not the floppy drive installed has 40 or
80 tracks. 360K type has 40 tracks while 760K, 1.2M and 1.44M all have 80 tracks.
By default, this field is set to Enabled.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the system. By
default, the system boots up with NumLock On.
Security Option
This field allows you to limit access to the System and Setup. The default value is
Setup. When you select System, the system prompts for the User Password every
time you boot up. When you select Setup, the system always boots up and prompts for
the Supervisor Password only when the Setup utility is called up.
PCI/VGA Palette Snoop
Some display cards that are non-standard VGA may not show colors properly. This
field allows you to set whether MPEG ISA/VESA VGA Cards can work with
PCI/VGA or not. When this field is enabled, a PCI/VGA can work with a MPEG
ISA/VESA VGA card. When this field is disabled, a PCI/VGA cannot work with a
MPEG ISA/VESA Card.
50
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM memory when
used with OS/2 that depends on certain BIOS calls to access memory. The default
setting is NON-OS/2.
Video BIOS Shadow
This item allows you to change the Video BIOS location from ROM to RAM. Video
Shadow will increase the video speed.
C8000 - CBFFF Shadow/DC000 - DFFFF Shadow
Shadowing a ROM reduces the memory available between 640KB to 1024KB. These
fields determine whether optional ROM will be copied to RAM or not.
PC-586U(PC) User’s Manual
51
Chapter 3 BIOS Configuration
Chipset Features Setup
This Setup menu controls the configuration of the Industrial CPU Card chipset.
ROM PCI/ISA BIOS
CHIPSET FEATURES SETUP
AWARD SOFTWARE INC.
DRAM Timing
System BIOS Cacheable
Video BIOS Cacheable
8 Bit I/O Recovery Time
16 Bit I/O Recovery Time
Memory Hole At 15M-16M
PCI 2.1 Compliance
:
:
:
:
:
:
70ns
Disabled
Disabled
1
1
Disabled
Disabled
** System Hardware Monitor *
CPU Warning Temperature:
70°C/158°F
Current CPU Temperature:
37°C/98°F
Current System Temp.
Current CPU Fan Speed
Current Chassis Fan Speed
VIO:
+12V:
-5V:
VCORE:
+5V:
-12V:
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
DRAM Timing
The DRAM timing is controlled by the DRAM Timing Registers. The timing type is
dependent on the system design. Slower rates may be required in some system
designs to support loose layouts or slower memory.
System BIOS Cacheable
Select Enabled allows caching of the system BIOS ROM at F000h-FFFFFh,
resulting in better system performance. However, if any program writes to this
memory area, a system error may result.
Video BIOS Cacheable
Select Enabled allows caching of the video BIOS ROM at C0000h-F7FFFh,
resulting in better video performance. However, if any program writes to this
memory area, a system error may result.
8 Bit I/O Recovery Time
This field allows you to select the recovery time allowed for 8 bit I/O. By default, this
field is set to 1 Clock.
16 Bit I/O Recovery Time
This field allows you to select the recovery time allowed for 16 bit I/O. By default,
this field is set to 1 Clock.
52
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
Memory Hole at 15M-16M
In order to improve performance, certain space in memory can be reserved for ISA
cards. This field allows you to reserve 15MB to 16MB memory address space to ISA
expansion cards. This makes memory from 15MB and up unavailable to the system.
Expansion cards can only access memory up to 16MB. By default, this field is set to
Disabled.
PCI 2.1 Compliance
Concurrent PCI allows multiple PCI transfers from the PCI master buses to memory
to CPU. By default, this field is set to Enabled.
CPU Warning Temperature
The onboard hardware thermal sensor monitors CPU temperature changes and
prevents the CPU from overheating. Alert is sounded through the speaker and CPU
speed slows down when the temperature exceeds the temperature set in the BIOS
until the temperature falls below a safe level. By default, this field is set to
70°C/158°F.
Temperature/Fan Speeds/Voltages
These read-only fields show the current CPU temperature, speeds in RPM
(revolution per minute) for the CPU fan and chassis fan, and current voltages in the
voltage regulators and power supply as monitored by the hardware monitoring IC.
PC-586U(PC) User’s Manual
53
Chapter 3 BIOS Configuration
Power Management Setup
The Power Management Setup allows you to save energy of your system effectively.
It will shut down the hard disk and turn off video display after a period of inactivity.
ROM PCI/ISA BIOS (2A59IM29)
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
Power Management
PM Control by APM
Video Off Method
Video Off After
Doze Mode
Standby Mode
Suspend Mode
HDD Power Down
Soft-off by PWR-BTTN
: Disabled
: Yes
: DPMS
: Suspend
: Disabled
: Disabled
: Disabled
: Disabled
: Instant-off
** Reload Global Timer Events **
IRQ3 [ 3-7, 9-15],NMI
: Enabled
Primary IDE 0
: Disabled
Primary IDE 1
: Disabled
Secondary IDE 0
: Disabled
Secondary IDE 1
: Disabled
Floppy Disk
: Disabled
Serial Port
: Enabled
Parallel Port
: Disabled
PWR On by Modem/LAN
Resume by Alarm
: Enabled
: Disabled
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Power Management
This field allows you to select the type of power saving management modes. There
are fours selections for Power Management.
Disable
No power management. (Default)
Min. Power Saving
Minimum power management.
Max. Power Saving
Maximum power management. Only available for
SL CPU.
User Define
Each of the ranges are from 1 min. to 1hr. Except for
HDD Power Down which ranges from 1 min. to 15
min.
PM Control by APM
This field allows you to use the Advanced Power Management device to enhance the
Max. Power Saving mode and stop the CPU’s internal clock. If the Max. Power
Saving is not enabled, this will be preset to NO.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn off vertical
and horizontal scanning.
DPMS
Allows the BIOS to control the video display card if it
supports DPMS.
Blank Screen
This option only writes blanks to the video buffer.
54
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
Video Off After
This field specifies the mode after which the Video Off feature is enabled. The
options are Doze, Standby, Suspend, and N/A.
Doze Mode
When enabled, and after the set time of system inactivity, the CPU clock will run at
a slower speed while all other devices still operate at full speed.
Standby Mode
When enabled, and after the set time of system inactivity, the fixed disk drive and the
video would be shut off while all other devices still operate at full speed.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices except the CPU
will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk drive will be
powered down while all other devices remain active.
Soft-Off by PWR-BTTN
This field defines the power-off mode when using an ATX power supply. The
Instant-Off mode allows powering off immediately upon pressing the power button.
In the Delay 4 Sec mode, the system powers off when the power button is pressed for
more than four seconds or places the system in a very low-power-usage state, with
only enough circuitry receiving power to detect power button activity. The default
value is Instant-Off.
Resume by Alarm
This allows the system to be turned on automatically through the timer set in the
BIOS to make the system more scheduleable. By default, this field is set to Disabled.
PWR On by Modem/LAN
This allows the system to be powered on through a modem or network. By default,
this field is set to Disabled.
PC-586U(PC) User’s Manual
55
Chapter 3 BIOS Configuration
Reload Global Timer Events
This section determines the reloading of the ‘timers’ after entering the Full On You
can enable or disable the monitoring of IRQ 8 (Real Time Clock) so it does not
awaken the system from Suspend mode.
56
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
PNP/PCI Configuration
This option configures the PCI bus system. All PCI bus systems on the system use
INT#, thus all installed PCI cards must be set to this value.
ROM PCI/ISA BIOS
PNP/PCI CONFIGURATION
AWARD SOFTWARE INC.
PNP OS Installed
Resources Controlled by
Reset Configuration Data
: Yes
: Manual
: Disabled
IRQ-3
IRQ-4
assigned to
assigned to
: Legacy ISA
: Legacy ISA
IRQ-5
assigned to
: PCI/ISA PnP
IRQ-7
assigned to
: Legacy ISA
IRQ-9
assigned to
: PCI/ISA PnP
IRQ-10 assigned to
: PCI/ISA PnP
IRQ-11 assigned to
: PCI/ISA PnP
IRQ-12 assigned to
: PCI/ISA PnP
IRQ-14 assigned to
: Legacy ISA
IRQ-15 assigned to
: Legacy ISA
DMA-0 assigned to
: PCI/ISA PnP
DMA-1
DMA-3
DMA-5
DMA-6
DMA-7
: PCI/ISA PnP
: PCI/ISA PnP
: PCI/ISA PnP
: PCI/ISA PnP
: PCI/ISA PnP
assigned
assigned
assigned
assigned
assigned
to
to
to
to
to
Used MEM base addr
: N/A
ESC : Quit
á â ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
PNP OS Installed
This field allows you to specify if the operating system installed in your system is
plug and play aware.
Note: Operating systems such as DOS, OS/2, and Windows 3.x do not use PnP.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices automatically.
However, this capability needs you to use a PnP operating system such as Windows
95. The default value is Manual.
Reset Configuration Data
This field allows you to determine whether to reset the configuration data or not.
The default value is Disabled.
IRQ, DMA assigned to
These fields allow you to determine the IRQ/DMA assigned to the ISA bus and is not
available to any PCI slot.
PC-586U(PC) User’s Manual
57
Chapter 3 BIOS Configuration
Used MEM base addr
This field allows the user to set the base address and block size of a legacy (non-PnP)
ISA card that uses any memory segment within the C800H and DFFFH address
range. If the you have such a card and are not using an ICU (ISA Configuration
Utility) to specify its address range, select a base address from the six available
options. During selection, the “Used MEM Length” field will appear with the block
size options. If you have more than one legacy ISA card in your system that require
the use of this address range, you can increase the block size to either 8K, 16K, 32K
or 64K. If you are using ICU to accomplish this task, leave “Used MEM base addr”
to its default setting of N/A.
58
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
Load BIOS Defaults
This option allows you to load the troubleshooting default values permanently stored
in the BIOS ROM. These default settings are non-optimal and disable all highperformance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
Load BIOS Defaults (Y/N)?
N & EXIT SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
To load BIOS defaults value to CMOS SRAM, enter “Y”. If not, enter “N”.
Load Setup Defaults
This option allows you to load the default values to your system configuration. These
default settings are optimal and enable all high performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE & EXIT SETUP
Load Setup Defaults (Y/N)? N
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter “N”.
PC-586U(PC) User’s Manual
59
Chapter 3 BIOS Configuration
Integrated Peripherals
This option allows you to determine your hard disk configuration, mode and port.
ROM PCI/ISA BIOS
INTEGRATED PERIPHERALS
AWARD SOFTWARE INC.
IDE HDD Block Mode
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
IDE Secondary Master PIO
IDE Secondary Slave PIO
: Enabled
: Auto
: Auto
: Auto
: Auto
: Auto
: Auto
IDE Secondary Master UDMA
: Auto
IDE Secondary Slave UDMA
: Auto
On-Chip Primary PCI IDE
: Enabled
On-Chip Secondary PCI IDE
: Enabled
USB Keyboard Support
: Disabled
Onboard FDD Controller
Serial Port 1
Serial Port 2
UART Mode Select
Onboard Parallel Port
Parallel Port Mode
: Enabled
: Auto
: Auto
: Standard
: 378H/IRQ7
: SPP
ESC : Quit
á â ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to transfer data
to and from your hard disk drive.
IDE Primary Master/Slave PIO And Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster. Rather than have
the BIOS issue a series of commands that transfer to or from the disk drive, PIO
(Programmed Input/Output) allows the BIOS to communicate with controller and
CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which primarily
differ in timing. When Auto is selected, the BIOS will select the best available mode.
IDE Primary Master/Slave UDMA And Secondary Master/Slave UDMA
This field allows your system to improve disk I/O throughput to 33Mb/sec with the
Ultra DMA/33 feature. The options are Auto and Disabled.
60
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
On-Chip Primary/Secondary PCI IDE
These fields allow you either to enable or disable the Primary/Secondary controller.
You might choose to disable the controller if you were to add a higher performance
or specialized controller.
USB Keyboard Support
This field allows your system to support a USB keyboard.
Onboard FDD Controller
This option allows you to select the onboard FDD port.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial/parallel port and its address. The
default value for these ports are:
Serial Port 1
3F8/IRQ4
Serial Port 2
2F8/IRQ3
Parallel Port
378H/IRQ7
UART Mode Select
This field determines the UART 2 mode in your computer. The options are
Standard, HPSIR, and ASKIR.
Onboard Parallel Mode
This field allows you to determine parallel port mode function.
SPP
Standard Printer Port
EPP
Enhanced Parallel Port
ECP
Extended Capabilities Port
ECP+EPP Extended Capabilities Port or Enhanced Parallel Port
PC-586U(PC) User’s Manual
61
Chapter 3 BIOS Configuration
Supervisor / User Password
These two options set the system password. Supervisor Password sets a password
that will be used to protect the system and Setup utility. User Password sets a
password that will be used exclusively on the system. To specify a password,
highlight the type you want and press <Enter>. The Enter Password: message
prompts on the screen. Type the password, up to eight characters in length, and press
<Enter>. The system confirms your password by asking you to type it again. After
setting a password, the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted to enter
the password. A message will confirm the password to be disabled. Once the
password is disabled, the system will boot and you can enter Setup freely.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
Enter Password:
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Change / Set / Disable Password
62
PC-586U(PC) User’s Manual
Chapter 3 BIOS Configuration
IDE HDD Auto Detection
This option detects the parameters of an IDE hard disk drive, and automatically
enters them into Standard CMOS Setup screen.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
HARD DISKS
TYPE
SIZE
CYLS
HEAD
PRECOMP
LANDZ
SECTOR
MODE
Primary Master:
Select Primary Master Option (N=SKIP) : N
OPTIONS
TYPE
SIZE
1 (Y)
0
0
CYLS HEAD PRECOMP
0
0
0
LANDZ
SECTOR
MODE
0
0
NORMAL
NOTE: Some OSes (like SCO-UNIX) must use ”NORMAL” for installation
ESC: SKIP
Up to four IDE drives can be detected, with parameters for each appearing in
sequence inside a box. To accept the displayed entries, press the “Y” key; to skip to
the next drive, press the “N” key. If you accept the values, the parameters will appear
listed beside the drive letter on the screen.
PC-586U(PC) User’s Manual
63
Chapter 3 BIOS Configuration
Save & Exit Setup
This option allows you to determine whether to accept the modifications or not. If
you type “Y”, you will quit the setup utility and save all changes into the CMOS
memory. If you type “N”, you will return to Setup utility.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
Save to CMOS and Exit (Y/N)?
PNP/PCI CONFIGURATION
SAVE N
& EXIT SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Save Data to CMOS & Exit Setup
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you have made
in this session. Typing “Y” will quit the Setup utility without saving the
modifications. Typing “N” will return you to Setup utility.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
Quit Without Saving (Y/N)? N
PNP/PCI CONFIGURATION
SAVE & EXIT SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Abandon all Data & Exit Setup
64
PC-586U(PC) User’s Manual
Chapter 4 VGA Driver Installation
4
VGA Driver Installation
This chapter provides information on how to install the VGA drivers that come in
the floppy diskette with your PC-586U(PC) card. Please follow the instructions set
forth in this chapter carefully. Please note that there must be relevant software
installed in your system before you could proceed to install the VGA drivers. It is
recommended that you make a copy of the VGA driver diskette and put the backup
copy in a safe place.
The following items are covered in this chapter:
Installing the Drivers for Windows 95..................................... 66
Driver Installation........................................................... 66
Installing the Drivers for Windows NT 4.0.............................. 67
Driver Installation........................................................... 67
PC-586U(PC) User’s Manual
65
Chapter 4 VGA Driver Installation
Installing the Drivers for Windows 95
Driver Installation
The following section describes the normal display driver installation procedures for
Windows 95. Use the following procedures when installing the display drivers for
Windows 95.
1. Click Start, then Settings, then Control Panel.
2. Double click on "Display".
3. Select the "Settings" page, click the "Change Display Type" button.
4. Click the "Change" button in the "Adapter Type" area.
5. Click the "Have Disk" button and press "OK".
6. Specify the path to the new driver and press <ENTER>:
Example 1: Insert the drivers disk in the A: floppy drive, and enter A:\win95.
Example 2: Type in the name of the directory where you copied the drivers, either on
your local hard drive or on a network share.
Example 3: If you're not sure exactly where the drivers are, choose the "Browse..."
button to find them.
7. The "Select Device" dialog box will appear. Select the adapter that corresponds
to the one you installed in your machine and click OK.
8. Windows 95 will copy the display drivers to the proper directories on your
system.
9. Continue choosing Close until asked to restart your machine from the "Systems
Settings Change" dialog box.
10. After the system has restarted, you can go back into the Display applet and
select alternate screen resolutions and color depths.
66
PC-586U(PC) User’s Manual
Chapter 4 VGA Driver Installation
Installing the Drivers for Windows NT 4.0
Driver Installation
Once you are in the Windows NT 4.0 environment, follow the procedures below to
install the VGA drivers in the diskette that comes with your CPU card.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Click the Start button, then go to Settings and click on Control Panel.
Click on the Display icon to start the Display Properties window.
Click on the Settings tab, and then click on Display Type.
In the Change Display Type window, click on Change in Adapter Type. This
will bring up the Select Device Window.
In the Change Display window, click on Have Disk. Follow the directions on
the screen to supply the directory where the Windows NT driver files are
located. Then select OK, or press ENTER.
Select Chips Video Accelerator from Display list provided, then click OK or
press ENTER.
You will then see a warning panel about Third Party Drivers. Click on Yes to
finish the installation.
Once the installation is complete, the system must be shut down and restarted
for the new drivers to take effect.
When the system has restarted, the default graphics mode ( usually
640x480x256color ) has been automatically selected. Click the Start button,
then go to Settings and click on Control Panel. Click on the Display icon to
start the Display Properties window. Click on the Settings tab. A new screen
setting can be selected using either of the following methods:
A. Use the slide-bar in the Desktop Area to select new setting.
B. Click on List All Modes. From the list provided, select a new setting, then
click OK or press ENTER.
C.
Click on Test to test the newly selected graphics mode. Follow the
instructions given on the screen. A test screen should appear, followed by
the Testing Mode window. Click on Yes to continue. Click on Apply to
switch to the new graphics mode. Graphics modes are changed
dynamically on NT 4.0, so you do not need to shut down and restart for the
new screen settings to work.
PC-586U(PC) User’s Manual
67
Chapter 4 VGA Driver Installation
This page was intentionally left blank.
68
PC-586U(PC) User’s Manual
Chapter 5 LAN Driver Installation Guide
5
LAN Driver Installation
Guide
This chapter describes LAN features and driver installation of the onboard Realtek
8139A Ethernet controller.
The following items are covered in this chapter:
Introduction ............................................................................ 70
Features .................................................................................. 70
Software Drivers Support ........................................................ 70
Installing LAN Driver for Win98/Windows2000..................... 71
Installing LAN Driver for Windows 95 ................................... 72
Installing LAN Driver for Windows NT.................................. 73
Installing LAN Driver for DOS............................................... 74
Installing Driver for Windows for Workgroups ....................... 75
PC-586U(PC) User’s Manual
69
Chapter 5 LAN Driver Installation Guide
Introduction
Realtek 8139A is a 32-bit 10/100MBps Ethernet controller for PCI local buscompliant PCs. It supports the bus mastering architecture, and Auto-negotiation
feature which make it possible to combine one common type of Ethernet cabling –
an RJ-45 connector for twisted-pair cabling that can be used for both 10Mbps and
100Mbps connection. Extensive driver support for commonly used network
operating systems is also provided.
Features
l
l
l
l
l
l
Conforms to the Ethernet IEEE 802.3u standard
Compatible with PCI Local Bus Revision 2.1 specification
IEEE 802.3u Auto-Negotiation for automatic speed selection
Supports Full-Duplex/Half-Duplex Operation
Provides 32-bit bus mastering data transfer
Supports 10Mbps and 100Mbps operation in a single port
Software Drivers Support
Novell network drivers:
Workstation for DOS ODI Client / OS/2 ODI Client
Server Driver for NetWare 3.11, 3.12, 4.0, 4.1X, 5.0
Client 32 for Windows 95
IBM network drivers:
LAN Server for OS/2 2.3, 4.0
Microsoft network drivers:
Microsoft Network Client for DOS, LAN Manager Workstation/Server, Windows
for Workgroups v3.11, Windows NT 3.5, 3.51 & 4.0, Windows 95 & OSR2,
Windows 98 & Windows 2000
UNIX network drivers:
SCO UNIX 4.X, 5.X
Other Network Operating System Information
Packet Driver, LANtastic 6.0 with NDIS driver
The following section describes the installation driver procedure for Windows
98/Windows 2000, Windows 95, Windows NT, DOS, and Windows for Workgroup.
To view the procedure of other operating systems, execute the help8139.exe in the
diskette supplied.
70
PC-586U(PC) User’s Manual
Chapter 5 LAN Driver Installation Guide
Installing LAN Driver for Win98/Windows2000
This section describes the procedure to install Windows 98 and Windows 2000
driver for Realtek RTL8139 PCI Fast Ethernet adapter.
Before you start with the installation process, make sure that your adapter is properly
installed in the PCI bus slot.
Executing Win98/Windows2000 will auto-detect your system configuration and
find the adapter hardware. (If Win98/Windows2000 does not prompt that it detects
the PCI Ethernet adapter, there must be something wrong with the Realtek
RTL8139 PCI Fast Ethernet adapter or your system environment.)
1. When asked to select the driver you want to install, select "Driver from disk
provided by hardware manufacturer".
2. Insert the Realtek RTL8139 driver disk into drive A and specify the setup file
pathname A:\.
3. Win98/Windows2000 will appear with a message to insert Win98/Win2000
system disk to complete setup.
4. Win98/Windows2000 will finish other installation procedure automatically, and
ask you to restart the system.
PC-586U(PC) User’s Manual
71
Chapter 5 LAN Driver Installation Guide
Installing LAN Driver for Windows 95
This section describes the procedure to install Windows 95 driver for Realtek
RTL8139 PCI Fast Ethernet adapter.
Before you start with the installation process, make sure that your adapter is properly
installed in the PCI bus slot. Executing Windows 95 will auto-detect your system
configuration and find the adapter hardware. (If Win95 does not prompt that it
detects the PCI Ethernet adapter, there must be something wrong with the RTL8139
PCI Fast Ethernet adapter or your system environment.)
1. When asked to select the driver you want to install, select "Driver from disk
provided by hardware manufacturer".
2. Insert the Realtek RTL8139 driver disk into drive A and specify the setup file
pathname A:\.
3. Windows 95 will appear with a message to insert Windows 95 system disk to
complete setup.
5. Windows 95 will finish other installation procedure automatically, and ask you to
restart the system.
72
PC-586U(PC) User’s Manual
Chapter 5 LAN Driver Installation Guide
Installing LAN Driver for Windows NT
This section describes the procedure to install Windows NT v3.5, v3.51 & v4.0
driver for Realtek RTL8139 PCI Fast Ethernet adapter.
When you are in Windows NT :
1. In the Main group of Windows NT, select the "Control Panel" icon.
2. In the Control Panel window, choose the "Network" icon.
3. In the Network Settings dialog box, choose the "Add Adapter" button. The Add
Network Adapter dialog box appears.
4. In the list of network cards, select "<other> Requires disk from manufacturer",
and then press <Enter> button.
5. Insert the Realtek driver disk in drive A, enter drive and pathname A:\ which is
the path where the setup file OEMSETUP.INF is located, and then choose the OK
button.
6. The screen will appear "Select Line Speed" dialog box which is provided by
RTL8139.SYS driver. The default value is "auto" so that the RTL8139 PCI Fast
Ethernet adapter and its driver RTL8139.SYS will auto-detect the line speed, 10
Mb or 100Mb, while the RTL8139.SYS is loading. The other values, "10" or
"100", are only used when you want to force RTL8139 PCI Fast Ethernet adapter
to 10Mb or 100Mb.
7. The screen will appear "Input EthernetID" dialog box which is provided by
RTL8139.SYS driver. This option is only required when you have more than one
Realtek RTL8139 PCI Fast Ethernet adapters on the computer. Select "SKIP" if
only one adapter installed on the computer.
8. "Bus Location" display in the next screen. Your machine contains more than one
hardware bus, please select the Bus Type and Bus number on
9. NT will then perform the binding process. If any additional network software
options were installed, you may be prompted for specific information for these
packages.
10. Restarting your system you will require network service.
PC-586U(PC) User’s Manual
73
Chapter 5 LAN Driver Installation Guide
Installing LAN Driver for DOS
Before you start with the installation procedure, make sure that the adapter is
properly installed and configured. Similarly, Make sure that your Microsoft
Network Client is properly installed. (If not, The installation utility SETUP.EXE is
located on Microsoft Network Client v3.0 for MS-DOS Disk. Run SETUP.EXE
from Disk and the SETUP program screen will appear. Follow the instructions. The
options are specific to your needs. The installation procedure will transfer files to a
specific directory on the client and modify existing configuration files to fit your
specific needs.)
1. Change to the Microsoft Network Client subdirectory, and run SETUP.EXE
2. The screen will display some information. Press <Enter>.
3. Respond to the screen prompts, selecting "Change Network Configuration", then
press <Enter>.
4. Move the highlight to "Add Adapter", press <Enter>.
5. Select "Network adapter not shown on list below ...".
6. Insert the Realtek RTL8139 driver diskette in floppy A, and specify the pathname
A:\NDIS2DOS, then press <Enter>.
7. Follow the screen instructions to complete the process. Simply pressing <Enter>
for each screen display will select the default options. Press <Enter> until you
reach the display prompting you to reboot the system.
74
PC-586U(PC) User’s Manual
Chapter 5 LAN Driver Installation Guide
Installing Driver for Windows for Workgroups
This section describes the procedure to install Microsoft Windows for Workgroups
v3.11 driver for REALTEK RTL8139 Fast Ethernet adapter.
1. When installing Windows for Workgroups, you are prompted for a network
driver. Select the "Unlisted or Updated Network Driver".
2. Insert the REALTEK adapter driver disk containing OEMSETUP.INF and
RTSND.DOS files.
3. Specify the directory for the driver (A:\WFW311) and select the Adapter driver.
4. Select Advanced options, and make sure the parameters match the card settings.
Check keyword "EtherID", which is provided by RTSND.DOS. The installation
program copies the necessary files and creates PROTOCOL.INI for use with the
adapter.
Existing Windows for Workgroups Installation:
1. Select the "Network Setup" icon in the Network Group.
2. Select the "Driver.." button.
3. Select the "Add Adapters.." button.
4. Select "Unlisted or Updated Network Adapter"
5. Insert the adapter driver disk with OEMSETUP.INF and RTSND.DOS and
specify the path A:\WFW311.
6. Select the REALTEK adapter driver.
7. The installation program copies the necessary files and creates PROTOCOL.INI
for use with the adapter.
8. Select "Close" and when prompted, restart the computer for changes to take affect
and complete the installation.
NOTE: You must have a terminated cable attached to the adapter when you start
Windows for Workgroups. If you don't, Windows for Workgroups hangs.
PC-586U(PC) User’s Manual
75
Chapter 5 LAN Driver Installation Guide
This page was intentionally left blank.
76
PC-586U(PC) User’s Manual
Chapter 6 SCSI Driver Installation Guide
6
SCSI Driver Installation
Guide
This chapter serves as an installation guide to the onboard SCSI interface on your
CPU card. It contains important information to ease the installation and
configuration process.
With the SCSI interface, you can connect SCSI peripherals such as hard disk drives,
scanners, CD-ROM drives and tape drives.
Topics covered in this chapter include:
Installing SCSI Driver for DOS............................................... 78
Installing SCSI Driver for Windows 95/98.............................. 79
Driver Installation for Windows-NT........................................ 81
Installing SCSI driver for OS/2 3.X & 4.X.............................. 83
PC-586U(PC) User’s Manual
77
Chapter 6 SCSI Driver Installation Guide
Installing SCSI Driver for DOS
The DOSSETUP.EXE program installs the 16bit ASPI drivers, SCSI CD-ROM
driver and the Microsoft CD extensions. This program will automatically create or
modify the AUTOEXEC.BAT and CONFIG.SYS files on your hard drive. To
complete CD-ROM installation, you will need MSCDEX.EXE pre-installed on the
hard drive or on a floppy disk. MSCDEX.EXE is on MS-DOS 6.2x Setup Disk
Number One. Be sure that you know the location and the path of MSCDEX.EXE
prior to running DOSSETUP.EXE. The hard drive will need MS-DOS 6.xx
installed or it will need to be formatted with the /s option (i.e. - bootable format)
prior to running Initio DOSSETUP.EXE. From the x:\ DOS prompt type
"DOSSETUP" and press "enter". NOTE: x = drive letter of floppy drive used. After
DOSSETUP.EXE completes, be sure to reboot system so changes take effect.
78
PC-586U(PC) User’s Manual
Chapter 6 SCSI Driver Installation Guide
Installing SCSI Driver for Windows 95/98
Files you need:
Information script files for installation: INIA100.INF.
Miniport device driver: INIA100.MPD.
Installation:
A: New Windows 95 installation:
B. Adding INI-A100U2W to an existing Windows 95/98:
C. Updating device driver:
A: New Windows 95/98 installation:
1. Run SETUP.EXE from the Windows 95/98 CD-ROM and follow the directions
on the screen.
2. After a Windows 95/98 session is established, select "My Computer/Control
Panel/System/Device Manager/Other devices/PCI SCSI Bus Controller" from the
Windows 95/98 desktop.
3. Click the "Driver" tab, then click the "Change Driver" tab.
4. Double click "SCSI controllers", then click the "Have Disk" button.
5. At the prompt, type in "A:\win95", insert Initio INI-A100U2W driver disk 1, and
click the "OK" button.
6. Select "Initio INI-A100U2W Host Adapter", click the "OK" button. Windows 95
will copy INIA100.MPD to your hard disk. Reboot to complete the driver
installation.
B. Adding INI-A100U2W to an existing Windows 95:
1. Install the Initio hardware as described in the User Manual/User Guide. Windows
95 will detect the presence of a new hardware.
2. When Windows 95 displays the following:
New Hardware Found
PCI SCSI Bus Controller
Select which driver you want to install for your new hardware:
* Driver from disk provided by hardware manufacture
OK Cancel Help
Click "OK".
PC-586U(PC) User’s Manual
79
Chapter 6 SCSI Driver Installation Guide
3. Windows 95 will then display the following:
Install From Disk
Insert the manufacturer's installation disk into the drive
selected, and then click OK
Copy manufacturer's files from A:\WIN95
Insert the Initio disk 1 into drive A: and Click "OK".
Windows 95 will interpret INIA100.INF script files and load INIA100.MPD driver
to win95/system/iosubsys directory.
4. Windows 95 will then display the following:
System Settings Changed
To finish setting up your new hardware, you must restart
your computer.
Do you want to restart your computer now?
Yes No
Remove the diskette from drive A: and Click "Yes".
C. Updating device driver:
1. From the Windows 95 desktop, select "My Computer/Control
Panel/System/Device Manager/SCSI Controller/Initio INI-A100U2W Host
Adapter".
2. Click "Driver" tab, and then click "Change Driver" tab.
3. Type "A:\win95" and insert Initio INI-A100U2W driver disk into floppy drive A:,
click "OK", Windows 95 will copy the new device driver into the hard disk.
80
PC-586U(PC) User’s Manual
Chapter 6 SCSI Driver Installation Guide
Driver Installation for Windows-NT
Files you need:
Script files for installation: txtsetup.oem, oemsetup.inf, disk1.
Device driver: INIA100.SYS
Installation:
A: Install Windows-NT on a hard drive from the INI-A100U2W SCSI Host adapter.
1. If you are installing Windows-NT from a floppy drive, locate the Windows-NT
Disk 1 for floppy Installation. Make a backup copy of this diskette.
2. If you are installing Windows-NT from a CD-ROM drive, locate the, WindowsNT Setup Disk for CD-ROM Installation. Make a backup copy of this diskette.
3. Put the disk into drive A and turn on your computer.
4. Follow the instructions, and select "CUSTOM SETUP".
5. Select "OTHER" from the list of "Additional SCSI Adapters". A message will
appear on the screen stating that, "Requires disk provided by a hardware
manufacturer". Insert the diskette containing INI-A100U2W device driver and
press ENTER.
6. Windows-NT will interpret the txtsetup.oem and oemsetup.inf script files and
load INIA100.SYS driver to xxx/system32/drivers directory.
B: Adding or Updating the Initio driver to an existing Windows-NT 4.0 booted from
IDE drive or different type of host adapter:
1. Establish a Windows-NT session.
- Select CONTROL PANEL from within the MY COMPUTER group.
- Select SCSI ADAPTERS from within the CONTROL PANEL group.
2. Select the DRIVERS tab from within the SCSI ADAPTERS group:
- In the DRIVERS window, select "ADD...".
3. In the INSTALL DRIVER window, select "HAVE DISK...".
4. In the INSTALL FROM DISK window that is displayed, enter the Initio Driver
path name:
- Insert INI-A1000U2W Driver Disk 1 into drive A:
- Type: A:\WINNT, select "OK"
PC-586U(PC) User’s Manual
81
Chapter 6 SCSI Driver Installation Guide
5. Select INITIO INI-A100U2W Host Adapter, select "OK" to install the
INIA100.SYS driver onto your hard disk drive.
6. In the WINDOWS NT SETUP window that is displayed, enter the Initio Driver
path name to continue:
- Type:A:\WINNT, select "CONTINUE"
7. This completes updating the Host Adapter Driver. Follow the on-screen directions
to restart your computer and activate the new driver.
8. It is highly recommended that you verify your Windows NT device
driver has
been properly installed by selecting MY COMPUTER from the desktop. Then
select CONTROL PANEL:
- Select SCSI ADAPTERS from within the CONTROL PANEL group
- Highlight INITIO INI-A100U2W SCSI HOST ADAPTER from within the
SCSI ADAPTERS listing, and select PROPERTIES. If "This device is working
properly" is displayed in the Device status box, the driver has been correctly
installed.
C: Floppyless SETUP
If you are running WINNT.EXE or WINNT32.EXE to install or upgrade Windows
NT, when system reboot and screen turn black with the text "Setup is inspecting your
computer's hardware configuration...",
You have two seconds to press 'F6' key to enter the DRIVER INSTALL
SCREEN, this is the time to insert Initio Windows NT installation diskette, and type
"A:\WINNT" to load the INI-A100U2W Windows NT
driver.
82
PC-586U(PC) User’s Manual
Chapter 6 SCSI Driver Installation Guide
Installing SCSI driver for OS/2 3.X & 4.X
I) Installation procedures for INI-A100u2W OS/2 3.X & 4.X device driver:
A) Installed as a secondary controller
1) Open the OS/2 System Folder.
2) Open the System Setup Folder.
3) Double-click "Device Driver Install".
4) Insert the Initio installation diskette into your floppy drive.
5) Change to the OS/2 directory.
6) Choose INIA100.ADD, then click INSTALL.
7) After installation is done, OS/2 will report the status.
B) Installed as a primary controller
1) Make backup copies of the OS/2 Diskette 1.
2) Copy the INIA100.ADD onto OS/2 Diskette 1.
3) Modify the config.sys file on Diskette 1 to add
BASEDEV=INIA100.ADD /V
4) Install OS/2 using the backup Diskette 1
II) Driver configuration options:
/V
Verbose mode provides detail information about driver when driver is
initialized
/!V
Non Verbose mode (default)
/ET
Driver assumes that all targets have more than one LUN (default)
/!ET
Driver assumes that all targets only have LUN 0
/Q:x
Specifies maximum number of tag commands per target
/!Q
No tag command
/B:(d,dd),. Scan devices only on PCI BUS d, DEVICE dd
/B:d
Scan all the devices on the PCI BUS d
/T:xxxx Target enable mask WORD (Default scan all targets)
/A:d
Adapter IDs are assigned based on BIOS address and then
PCI device address
/DM:d,.. Enable direct access storage device (DASD) support on target d
/!DM:d,.. Disable DASD manager support on target d
/SM:d,.. Enable SCSI manager support on target d
/!SM:d,.. Disable SCSI manager support on target d
PC-586U(PC) User’s Manual
83
Chapter 6 SCSI Driver Installation Guide
This page was intentionally left blank.
84
PC-586U(PC) User’s Manual
Chapter 7 Intel PIIX Bus Master IDE Driver Installation
7
Intel PIIX Bus Master
IDE Driver Installation
This chapter describes the installation procedure for Intel PIIX Bus Master IDE
Drivers for Windows 95.
This chapter contains the following sections:
System Requirements.............................................................. 86
Installing the Software ............................................................ 87
PC-586U(PC) User’s Manual
85
Chapter 7 Intel PIIX Bus Master IDE Driver Installation
System Requirements
This section describes system requirements for the PIIX Bus Master IDE Device
Driver for Windows 95*. This driver has been designed for and tested with Windows
95 only. This driver will only install on systems with Windows 95.
1.
The system must contain a supported Intel processor and chipset configuration.
2.
Ensure that a mouse is connected to the system.
3.
One of the following versions of Windows 95* must be installed on the system
prior to running utility program.
Windows 95* 4.00.950
Windows 95* 4.00.950a
Windows 95* 4.00.950b
Windows 95* 4.00.950b
(Retail)
(OSR1)
(OSR2 without USB Supplement)
(OSR2.1 with USB Supplement)
4.
This utility should only be used on desktop systems. The utility must not be
executed on notebook or portable systems with or without dock.
5.
It is assumed that the BIOS properly initialized the 82371xB IDE interface for
Bus Master IDE operation.
6.
There are no other non-82371xB IDE controllers (add-in IDE controller or
sound card with IDE) enabled on the system.
86
PC-586U(PC) User’s Manual
Chapter 7 Intel PIIX Bus Master IDE Driver Installation
Installing the Software
This subsection describes how to install the software on a system where
Windows 95 is installed.
NOTE: Record the location of the Windows 95* directory before installing the
driver.
1.
Check the System Requirements. Windows 95* must be fully installed and
running on the system prior to running this software.
2.
Close any running applications.
3.
Remove references to installed real-mode IDE device drivers in the
AUTOEXEC.BAT and CONFIG.SYS files (especially any drivers that control
ATAPI CD-ROM and special IDE features). Use the Notepad utility to do this.
The driver files are stored in an integrated application setup program. This program
is a Windows 95* program that allows the driver files to be INSTALLED or
DE-INSTALLED.
Execute the driver setup program.
Run SETUP.EXE.
4.
Click 'Next' on Welcome Screen to read and agree to the license agreement.
View the text file and choose File\Exit to close Notepad and continue. NOTE:
If you click 'No', program will terminate.
5.
Click 'Yes' if you agree to continue. NOTE: If you click 'No', the program will
terminate.
6.
Select 'INSTALL', to install the PIIX Bus Master IDE Device Driver when
prompted to do so.
NOTE: If the driver is currently installed on the system, SETUP will ask you
whether or not you want to continue. Follow the prompts on the screen to
Install the driver if desired.
7.
Click 'OK' to restart the system when prompted to do so.
8.
Follow the screen instructions and use default settings to complete the setup
when Windows 95* is re-started. Upon re-start, Windows 95* will display that
it has found an Intel PCI Bus Master IDE controller hardware and is installing
hardware for it.
PC-586U(PC) User’s Manual
87
Chapter 7 Intel PIIX Bus Master IDE Driver Installation
If a "New Hardware Found" dialog box is displayed requesting the location of the
drivers, use the mouse to click on the scrollbar and click on the <Windows 95*
directory>\System\IOSubSys path:
For example:
Click on 'C:\WINDOWS\SYSTEM\IOSUBSYS\'
Click 'OK'.
9.
Select 'Yes', when prompted to re-start Windows 95.
NOTE: After installation, the following driver and related files are stored as
listed.
<Windows 95* directory>\System\IOSubSys\IDEATAPI.MPD
<Windows 95* directory>\System\IOSubSys\PIIXVSD.VXD
<Windows 95* directory>\INF\IDEATAPI.INF
88
PC-586U(PC) User’s Manual
Appendix
Appendix
A. I/O Port Address Map
B. Interrupt Request Lines (IRQ)
PC-586U(PC) User’s Manual
89
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses which
also becomes the identity of the device. There are a total of 1K port address space
available. The following table lists the I/O port addresses used on the Industrial CPU
Card.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278 - 27F
294h - 297h
2F8h - 2FFh
2B0 - 2DF
378h - 3FFh
360 - 36F
3B0 - 3BF
3C0 - 3CF
3D0 - 3DF
3F0h - 3F7h
3F8h - 3FFh
90
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Hard Ware Monitor Device (W83781D)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
PC-586U(PC) User’s Manual
Appendix
B. Interrupt Request Lines (IRQ)
There are a total of 15 IRQ lines available on the Industrial CPU Card. Peripheral
devices use interrupt request lines to notify CPU for the service required. The
following table shows the IRQ used by the devices on the Industrial CPU Card.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Parallel Port #2
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Software Redirected to Int 0Ah
Reserved
Reserved
Reserved
80287
Primary IDE
Secondary IDE
PC-586U(PC) User’s Manual
91
A-46-101
LZJ8881
CONTEC Group
010612 [990826]
PC-586U(PC) User’s Manual
93
CONTEC Group
JAPAN
: Headquarters
CONTEC Co., LTD.
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Tel
: +81 (6) 6477-5219
Fax : +81 (6) 6477-1692
E-mail
: intsales@osaka.contec.co.jp
U.S.A.
: CONTEC MICROELECTRONICS U.S.A. INC.
744 South Hillview Drive. Milpitas, CA 95035 U.S.A.
Tel
: +1 (408) 719-8200
Fax : +1 (408) 719-6750
E-mail
: tech_support@contecusa.com
EUROPE
: CONTEC MICROELECTRONICS EUROPE B.V.
Binnenweg 4, 2132 CT, Hoofddorp, The Netherlands
Tel
: +31 (23) 567-3030
Fax : +31 (23) 567-3035
E-mail
: tech_support@conteceu.nl
KOREA
: HYOJIN CONTEC Co., LTD.
KI-IM Bldg. #399, Shindolim-Dong, Kuro-ku, Seoul 152-070, Korea
Tel
: +82 (2) 2636-4277/8
Fax : +82 (2) 2636-4279
E-mail
: product@conteck.com
CHINA
:
INTERNATIONAL CONTEC TECHNOLOGY CO., LTD.
B-8F, Hua Tong Building, No. B19, Che Gong Zhuang West Road,
Hai Dian District, Beijing 100044, China
Tel
: +86 (10) 8801-8228
Fax : +86 (10) 8801-8209
E-mail
: ict@ict.com.cn
SHANGHAI CONTEC MICROELECTRONICS CORPORATION.
No. 481, Gui Ping Road, Cao He Jing, Hi-Tech Park, Shanghai 200233, China
Tel
: +86 (21) 6485-1907
Fax : +86 (21) 6485-0330
E-mail
: contec@contec.com.cn
SHENYANG CONTEC MICROELECTRONICS Co., LTD.
No. 169, Qingnian Street, Shenhe District, Shenyang 110015, China
Tel
: +86 (24) 2392-9771
Fax : +86 (24) 2392-9773
TAIWAN
: MACROMATE CORP.
8F, Universal Center, No.179, Sec.1, Ta-Tung Road, Hsi-Chih, Taipei Hsien, Taiwan
R.O.C.
Tel
: +886 (2) 2647-9353
Fax : +886 (2) 2647-9373
E-mail
: intl@macromate.com.tw
A-46-368
Ver. 2001. 11. 06
Download PDF