Bestway Flowclear 58400 Owner's Manual
Bestway Flowclear 58400 is a sand filter for storable pools that provides efficient water filtration and circulation, ensuring a clean and refreshing swimming environment. With a powerful 200W motor, it has a maximum flow rate of 3,000 L/h and can handle pools up to 17,000 L. The 6-function control valve allows you to filter, rinse, circulate, backwash, close, and drain the pool water, giving you complete control over your pool's cleanliness. The filter uses pool-grade #20 Silica sand (not included) for effective filtration and has a sand capacity of 18 kg.
Advertisement
Advertisement
#58400
220-240V~50Hz, 200W
Hmax 1.5m Hmin 0.19m IPX5
TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals Or
Spare Parts, Please Visit www.bestwaycorp.com
FLOWCLEAR™ SAND FILTER
OWNER’S MANUAL www.bestwaycorp.com
Visit Bestway YouTube channel
S-S-004293
2
S-S-004293
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW ALL
SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
• The pump is to be supplied by an isolating transformer or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
• The appliance must be supplied by earthed power source.
•
RISK OF ELECTRIC SHOCK
- The pump cannot be used while people are inside the pool. Forbid the access of the pool in case of damage of the sand filter.
•
DO NOT BURY CORD.
Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Extension cords can’t be used.
• Risk of electric shock. Using the sand filter with an unmatched electrical supply is dangerous and will permanently damage the sand filter.
• Do not remove the grounding prong or modify the plug in anyway. Do not use adaptor plugs.
Consult a qualified electrician for any questions relating to validity of your plugs or grounding.
• Handle the sand filter with care. Do not pull or carry the sand filter by the power cord. Never pull a plug from the outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects, oil, moving parts, and heat should never be exposed to the sand filter.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
• This appliance is not intended for use by persons (including children) with reduced physical , sensory or mental capabilities , or lack of experience and knowledge , unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Don’t plug or unplug the appliance if hand is wet.
• Always unplug the appliance:
• On raining days
• Before cleaning or other maintenance
• Leave it unattended on holidays
• Safekeeping the instruction. For reconstruction the pool set every time, please always refer to the instructions.
• If instruction is missed, please contact with Bestway or search it in website: www.bestwaycorp.com
• Electric installations should follow national wiring rules. Consult a qualified electrician for any questions.
Pool fencing laws affect this product, consult your local council.
Empty and store safely when not in use.
CAUTION: This sand filter is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
3
S-S-004293
NOTES:
• Place the sand filter on solid, level ground.
• Pay attention to position pool and sand filter so adequate ventilation, drainage, and access for maintenance is available. Never place the sand filter in an area that may accumulate water, or on a walking path with lots of foot traffic.
• It is necessary to have the plug accessible after installation of the pool. The plug of the sand filter shall be at least 3.5m away from the pool.
• Atmospheric conditions may affect the performance and life span of the sand filter; take adequate precautions to protect the sand filter from unnecessary wear and tear that may occur during periods of cold or hot weather and/or exposure to sun.
• Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
• It is imperative to change as soon as possible all deteriorated parts. Only use parts approved by the manufacturer.
• Do not allow children or adults to lean or sit on the apparatus.
• Do not add chemicals to the sand filter.
• When chemical products are used to clean the pool water, it is recommended to respect a minimum filtration time to preserve the health of swimmers which depends on compliance of health regulation.
• This product is not intended for commercial use.
• Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock.
• When the appliance will be not used for long time, such as in the winter, the pool set should be disassembled and stored indoor.
• Caution Read the instruction before using the appliance and installation/reassembly every time.
SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW ALL
SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
• The pump is to be supplied by an isolating transformer or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
• The appliance must be supplied by earthed power source.
•
RISK OF ELECTRIC SHOCK
- The pump cannot be used while people are inside the pool. Forbid the access of the pool in case of damage of the sand filter.
•
DO NOT BURY CORD.
Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Extension cords can’t be used.
• Risk of electric shock. Using the sand filter with an unmatched electrical supply is dangerous and will permanently damage the sand filter.
• Do not remove the grounding prong or modify the plug in anyway. Do not use adaptor plugs.
Consult a qualified electrician for any questions relating to validity of your plugs or grounding.
• Handle the sand filter with care. Do not pull or carry the sand filter by the power cord. Never pull a plug from the outlet by yanking the power cord. Keep cord free from abrasions. Sharp objects, oil, moving parts, and heat should never be exposed to the sand filter.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
• This appliance is not intended for use by persons (including children) with reduced physical , sensory or mental capabilities , or lack of experience and knowledge , unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Don’t plug or unplug the appliance if hand is wet.
• Always unplug the appliance:
• On raining days
• Before cleaning or other maintenance
• Leave it unattended on holidays
• Safekeeping the instruction. For reconstruction the pool set every time, please always refer to the instructions.
• If instruction is missed, please contact with Bestway or search it in website: www.bestwaycorp.com
• Electric installations should follow national wiring rules. Consult a qualified electrician for any questions.
Pool fencing laws affect this product, consult your local council.
Empty and store safely when not in use.
CAUTION: This sand filter is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
NOTES:
• Place the sand filter on solid, level ground.
• Pay attention to position pool and sand filter so adequate ventilation, drainage, and access for maintenance is available. Never place the sand filter in an area that may accumulate water, or on a walking path with lots of foot traffic.
• It is necessary to have the plug accessible after installation of the pool. The plug of the sand filter shall be at least 3.5m away from the pool.
• Atmospheric conditions may affect the performance and life span of the sand filter; take adequate precautions to protect the sand filter from unnecessary wear and tear that may occur during periods of cold or hot weather and/or exposure to sun.
• Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
• It is imperative to change as soon as possible all deteriorated parts. Only use parts approved by the manufacturer.
• Do not allow children or adults to lean or sit on the apparatus.
• Do not add chemicals to the sand filter.
• When chemical products are used to clean the pool water, it is recommended to respect a minimum filtration time to preserve the health of swimmers which depends on compliance of health regulation.
• This product is not intended for commercial use.
• Cleaning and user maintenance must be performed by an adult above18 years old who is familiar with the risk of electric shock.
• When the appliance will be not used for long time, such as in the winter, the pool set should be disassembled and stored indoor.
• Caution Read the instruction before using the appliance and installation/reassembly every time.
SAVE THESE INSTRUCTIONS
4
S-S-004293
23
23
12
12
2
23 27 23 26 23
Optional Parts
22
23
26
25
2 7
21
20
6
6
2
2
3
3
3
2
2
5
5
S-S-004293
CONTROL VALVE OVERVIEW
WARNING: To prevent equipment damage and possible injury, always switch off the sand filter before changing the Control Valve fuction. Changing valve positions while the pump is running can damage the Control Valve, which may cause personal injury or property damage.
How to Use the Control Valve
Press down on the Control Valve handle and rotate to desired function.
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter functions: Filter, Rinse, Circulate, Backwash, Closed and Drain.
Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool.
Backwash: This function is used to clean the sand bed; water is pumped down through the Collector Hub, upwards through the sand bed, and deposited out of Port D.
Rinse: This function for initial startup, cleaning, and sand bed leveling after Backwash; water is pumped downwards through the sand bed, up through the
Collector Hub and deposited out of the valve Port D.
Circulate: This function circulates pool water bypassing the sand filter; use this function if the filter is broken to collect debris in the Debris Screens.
Drain: This function drains water from the pool; another filter bypass setting, water is pumped and deposited out of Port D, instead of returning it to the pool.
Closed: This function stops water flowing between the sand filter and the pool.
NOTE
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the
Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.8cm)
1) Connect the Hose Adaptor (22) with Adapter Nut (21) to both two ends of the hoses and tighten with the hose clamps (24).
2 2 2 1
24
2) Attach the Hoses to the Sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position.
3) Attach the Hoses to the connection valves on the pool. Ensure the corresponding letters on both the pool and the Sand filter match (A to A, B to B).
6
Pool
Pool
S-S-004293
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor(11).
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor(21)
NOTE:
1. Garden hose adaptor can be used for draining only, and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is damaged.
If equipmentis damaged, immediately notify the retailer from where the equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filterso the Ports and Control Valve are accessible for operation, servicing and winterizing.
3. IEC60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 18kg. The mounting holes should be 8mm in diameter and spaced 110mm apart. Use two bolts and nuts with a maximum of
8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one
18kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: SAND NOT INCLUDED.
1. Turn the nut counter clockwise to release the flange clamp and remove the Top Tank.
2. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. Do not pour the sand into the pipe of the Hub. #20 Silica sand 0.45-0.85mm, approximately 18 kg.
3. Ensure the O-ring is in place on the rim of the Bottom Tank. Make sure the O-ring and the rim of the Bottom Tank are clean without nicks, tears, scraps or sand. Attach the Top Tank to the Bottom Tank, place the Flange Clamp over the seam and turn the Nut clockwise to fasten it .
4. Attach the Control Valve to the Top Tank, ensuring the O-ring is in place on the rim of the
Top Tank. Make sure the O-ring and the rim of the Top Tank are clean without nicks, tears, scrapes or sand and that the vertical pipe of the Hub is inserted into the base of the
Control Valve.
5. Make sure Port C on the Control Valve is aligned with Port C on the Pump. Attach the Top
Flange Clamp and screw into position.
6. Attach the Piping to Pump Port C and to
Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping.
Section II: Hose Configuration for Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function. Your pool should be filled with water, make certain all of the pool’s Debris Screens (25)are fully submerged in water.
Please check if your product includes a T-Joint (25)(see Fig. E).
Please check if your product includes a T-Joint (27)(see Fig. E). If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A(see Fig.A-1)
1. Attach one end of the long hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Attach the T-joint(27) to the other end of the long hose(24).
3. Attach one end of both the short hoses(26) to the T-joint(27), and the other end to the pool’s Outlet “B”. Tighten the Hose clamps(23) of the T-joint(27).
4. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
Method B(see Fig.B-1)
1. Attach one Hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect the other end of the Hose(24) to the pool’s Outlet B.
3. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
4. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool outlet are properly aligned.
• Screw the other Hose to Port D and place the opposite end in drain area.
• With the Hoses attached, you can proceed to fill the pool, refer to pool owner’s manual for filling instructions.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Unplug the sand filter and set the Control Valve to the Rinse function.
4. Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Unplug the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Unplug the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Fourth Hose
NOTE: It is imperative to check that the hydraulic connectors are not closed.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1. Detach the Hose from Port D.
2. Attach the Hose (24) to the Control Valve’s Port A; screw the threaded locking ring into position.
3. Connect the other end of Hose(24) to the pool’s Inlet A.
4. Remove the Stopper Plug from the pool’s Inlet A and insert Debris Screen ( 25 ) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool Inlet are properly aligned.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
Sand Filter Maintenance
CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure
Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in
Section II and Section III: Backwash and Rinsing.
NOTE: The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
NOTE: We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Replace the Debris Screens with Stopper Plugs to prevent water from escaping.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Remove the Stopper Plugs and insert the Debris Screens
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
NOTE: Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage.
Allowing water to freeze will damage the sand filter and warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the
Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.8cm)
1) Connect the Hose Adaptor (22) with Adapter Nut (21) to both two ends of the hoses and tighten with the hose clamps (24).
2) Attach the Hoses to the Sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position.
3) Attach the Hoses to the connection valves on the pool. Ensure the corresponding letters on both the pool and the Sand filter match (A to A, B to B).
GARDEN HOSE ADAPTOR FUNCTIONS
11 21
1
1. Assemble the garden hose adaptor(11).
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor(21)
NOTE:
2
3
1. Garden hose adaptor can be used for draining only, and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
110mm Ø8mm
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is damaged.
If equipmentis damaged, immediately notify the retailer from where the equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filterso the Ports and Control Valve are accessible for operation, servicing and winterizing.
3. IEC60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 18kg. The mounting holes should be 8mm in diameter and spaced 110mm apart. Use two bolts and nuts with a maximum of
8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one
18kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: SAND NOT INCLUDED.
1. Turn the nut counter clockwise to release the flange clamp and remove the Top Tank.
2. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. Do not pour the sand into the pipe of the Hub. #20 Silica sand 0.45-0.85mm, approximately 18 kg.
3. Ensure the O-ring is in place on the rim of the Bottom Tank. Make sure the O-ring and the rim of the Bottom Tank are clean without nicks, tears, scraps or sand. Attach the Top Tank to the Bottom Tank, place the Flange Clamp over the seam and turn the Nut clockwise to fasten it .
4. Attach the Control Valve to the Top Tank, ensuring the O-ring is in place on the rim of the
1 2 3
Top Tank. Make sure the O-ring and the rim of the Top Tank are clean without nicks, tears, scrapes or sand and that the vertical pipe of the Hub is inserted into the base of the
Control Valve.
5. Make sure Port C on the Control Valve is aligned with Port C on the Pump. Attach the Top
Flange Clamp and screw into position.
6. Attach the Piping to Pump Port C and to
Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping.
.
4
O-ring
Nut
Nut
5
C
C
MAX
MIN .
.
O-ring
6
Nut
C
C
Nut
7
S-S-004293
Section II: Hose Configuration for Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function. Your pool should be filled with water, make certain all of the pool’s Debris Screens (25)are fully submerged in water.
Please check if your product includes a T-Joint (25)(see Fig. E).
Please check if your product includes a T-Joint (27)(see Fig. E). If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A(see Fig.A-1)
1. Attach one end of the long hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Attach the T-joint(27) to the other end of the long hose(24).
3. Attach one end of both the short hoses(26) to the T-joint(27), and the other end to the pool’s Outlet “B”. Tighten the Hose clamps(23) of the T-joint(27).
4. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
Method B(see Fig.B-1)
1. Attach one Hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect the other end of the Hose(24) to the pool’s Outlet B.
3. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
4. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool outlet are properly aligned.
• Screw the other Hose to Port D and place the opposite end in drain area.
• With the Hoses attached, you can proceed to fill the pool, refer to pool owner’s manual for filling instructions.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Unplug the sand filter and set the Control Valve to the Rinse function.
4. Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Unplug the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Unplug the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Fourth Hose
NOTE: It is imperative to check that the hydraulic connectors are not closed.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1. Detach the Hose from Port D.
2. Attach the Hose (24) to the Control Valve’s Port A; screw the threaded locking ring into position.
3. Connect the other end of Hose(24) to the pool’s Inlet A.
4. Remove the Stopper Plug from the pool’s Inlet A and insert Debris Screen ( 25 ) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool Inlet are properly aligned.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
Sand Filter Maintenance
CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure
Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in
Section II and Section III: Backwash and Rinsing.
NOTE: The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
NOTE: We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Replace the Debris Screens with Stopper Plugs to prevent water from escaping.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Remove the Stopper Plugs and insert the Debris Screens
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
NOTE: Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage.
Allowing water to freeze will damage the sand filter and warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the
Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.8cm)
1) Connect the Hose Adaptor (22) with Adapter Nut (21) to both two ends of the hoses and tighten with the hose clamps (24).
2) Attach the Hoses to the Sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position.
3) Attach the Hoses to the connection valves on the pool. Ensure the corresponding letters on both the pool and the Sand filter match (A to A, B to B).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor(11).
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor(21)
NOTE:
1. Garden hose adaptor can be used for draining only, and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is damaged.
If equipmentis damaged, immediately notify the retailer from where the equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filterso the Ports and Control Valve are accessible for operation, servicing and winterizing.
3. IEC60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 18kg. The mounting holes should be 8mm in diameter and spaced 110mm apart. Use two bolts and nuts with a maximum of
8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one
18kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: SAND NOT INCLUDED.
1. Turn the nut counter clockwise to release the flange clamp and remove the Top Tank.
2. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. Do not pour the sand into the pipe of the Hub. #20 Silica sand 0.45-0.85mm, approximately 18 kg.
3. Ensure the O-ring is in place on the rim of the Bottom Tank. Make sure the O-ring and the rim of the Bottom Tank are clean without nicks, tears, scraps or sand. Attach the Top Tank to the Bottom Tank, place the Flange Clamp over the seam and turn the Nut clockwise to fasten it .
4. Attach the Control Valve to the Top Tank, ensuring the O-ring is in place on the rim of the
Top Tank. Make sure the O-ring and the rim of the Top Tank are clean without nicks, tears, scrapes or sand and that the vertical pipe of the Hub is inserted into the base of the
Control Valve.
5. Make sure Port C on the Control Valve is aligned with Port C on the Pump. Attach the Top
Flange Clamp and screw into position.
6. Attach the Piping to Pump Port C and to
Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping.
Section II: Hose Configuration for Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function. Your pool should be filled with water, make certain all of the pool’s Debris Screens (25)are fully submerged in water.
Please check if your product includes a T-Joint (25)(see Fig. E).
Please check if your product includes a T-Joint (27)(see Fig. E). If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A(see Fig.A-1)
1. Attach one end of the long hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Attach the T-joint(27) to the other end of the long hose(24).
3. Attach one end of both the short hoses(26) to the T-joint(27), and the other end to the pool’s Outlet “B”. Tighten the Hose clamps(23) of the T-joint(27).
4. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
Method B(see Fig.B-1)
1. Attach one Hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect the other end of the Hose(24) to the pool’s Outlet B.
3. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
4. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool outlet are properly aligned.
• Screw the other Hose to Port D and place the opposite end in drain area.
• With the Hoses attached, you can proceed to fill the pool, refer to pool owner’s manual for filling instructions.
>1/2 in
A
>1/2 in
B
>1/2 in
A
>1/2 in
B
P61318 P6680 P61318 P6680
27
A
D
B
26
A 23
23
B
23
27
23
26
A
D
A
B
23
B
24
Fig.A-1
B
24 Fig.B-1
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Unplug the sand filter and set the Control Valve to the Rinse function.
4. Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Unplug the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Unplug the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
8
S-S-004293
Section IV: Complete Sand Filter Installation
Connect the Fourth Hose
NOTE: It is imperative to check that the hydraulic connectors are not closed.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1. Detach the Hose from Port D.
2. Attach the Hose (24) to the Control Valve’s Port A; screw the threaded locking ring into position.
3. Connect the other end of Hose(24) to the pool’s Inlet A.
4. Remove the Stopper Plug from the pool’s Inlet A and insert Debris Screen ( 25 ) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool Inlet are properly aligned.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
Sand Filter Maintenance
CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure
Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in
Section II and Section III: Backwash and Rinsing.
NOTE: The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
NOTE: We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Replace the Debris Screens with Stopper Plugs to prevent water from escaping.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Remove the Stopper Plugs and insert the Debris Screens
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
NOTE: Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage.
Allowing water to freeze will damage the sand filter and warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the
Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.8cm)
1) Connect the Hose Adaptor (22) with Adapter Nut (21) to both two ends of the hoses and tighten with the hose clamps (24).
2) Attach the Hoses to the Sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position.
3) Attach the Hoses to the connection valves on the pool. Ensure the corresponding letters on both the pool and the Sand filter match (A to A, B to B).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor(11).
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor(21)
NOTE:
1. Garden hose adaptor can be used for draining only, and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is damaged.
If equipmentis damaged, immediately notify the retailer from where the equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filterso the Ports and Control Valve are accessible for operation, servicing and winterizing.
3. IEC60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 18kg. The mounting holes should be 8mm in diameter and spaced 110mm apart. Use two bolts and nuts with a maximum of
8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one
18kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: SAND NOT INCLUDED.
1. Turn the nut counter clockwise to release the flange clamp and remove the Top Tank.
2. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. Do not pour the sand into the pipe of the Hub. #20 Silica sand 0.45-0.85mm, approximately 18 kg.
3. Ensure the O-ring is in place on the rim of the Bottom Tank. Make sure the O-ring and the rim of the Bottom Tank are clean without nicks, tears, scraps or sand. Attach the Top Tank to the Bottom Tank, place the Flange Clamp over the seam and turn the Nut clockwise to fasten it .
4. Attach the Control Valve to the Top Tank, ensuring the O-ring is in place on the rim of the
Top Tank. Make sure the O-ring and the rim of the Top Tank are clean without nicks, tears, scrapes or sand and that the vertical pipe of the Hub is inserted into the base of the
Control Valve.
5. Make sure Port C on the Control Valve is aligned with Port C on the Pump. Attach the Top
Flange Clamp and screw into position.
6. Attach the Piping to Pump Port C and to
Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping.
Section II: Hose Configuration for Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function. Your pool should be filled with water, make certain all of the pool’s Debris Screens (25)are fully submerged in water.
Please check if your product includes a T-Joint (25)(see Fig. E).
Please check if your product includes a T-Joint (27)(see Fig. E). If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A(see Fig.A-1)
1. Attach one end of the long hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Attach the T-joint(27) to the other end of the long hose(24).
3. Attach one end of both the short hoses(26) to the T-joint(27), and the other end to the pool’s Outlet “B”. Tighten the Hose clamps(23) of the T-joint(27).
4. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
Method B(see Fig.B-1)
1. Attach one Hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect the other end of the Hose(24) to the pool’s Outlet B.
3. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
4. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool outlet are properly aligned.
• Screw the other Hose to Port D and place the opposite end in drain area.
• With the Hoses attached, you can proceed to fill the pool, refer to pool owner’s manual for filling instructions.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Unplug the sand filter and set the Control Valve to the Rinse function.
4. Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Unplug the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Unplug the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Fourth Hose
NOTE: It is imperative to check that the hydraulic connectors are not closed.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1. Detach the Hose from Port D.
2. Attach the Hose (24) to the Control Valve’s Port A; screw the threaded locking ring into position.
3. Connect the other end of Hose(24) to the pool’s Inlet A.
4. Remove the Stopper Plug from the pool’s Inlet A and insert Debris Screen ( 25 ) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool Inlet are properly aligned.
>1/2 in
A
>1/2 in
B
>1/2 in
A
>1/2 in
B
P61318 P6680 P61318 P6680
27
A
A
24
23
B
26
23
23
B
23
27
26
23
24
Fig.A-2
24
23
B
23
24
Fig.B-2
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
Sand Filter Maintenance
CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure
Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in
Section II and Section III: Backwash and Rinsing.
NOTE: The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
NOTE: We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently.
9
S-S-004293
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Replace the Debris Screens with Stopper Plugs to prevent water from escaping.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Remove the Stopper Plugs and insert the Debris Screens
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
NOTE: Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage.
Allowing water to freeze will damage the sand filter and warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the
Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.8cm)
1) Connect the Hose Adaptor (22) with Adapter Nut (21) to both two ends of the hoses and tighten with the hose clamps (24).
2) Attach the Hoses to the Sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position.
3) Attach the Hoses to the connection valves on the pool. Ensure the corresponding letters on both the pool and the Sand filter match (A to A, B to B).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor(11).
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor(21)
NOTE:
1. Garden hose adaptor can be used for draining only, and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is damaged.
If equipmentis damaged, immediately notify the retailer from where the equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filterso the Ports and Control Valve are accessible for operation, servicing and winterizing.
3. IEC60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 18kg. The mounting holes should be 8mm in diameter and spaced 110mm apart. Use two bolts and nuts with a maximum of
8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one
18kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: SAND NOT INCLUDED.
1. Turn the nut counter clockwise to release the flange clamp and remove the Top Tank.
2. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. Do not pour the sand into the pipe of the Hub. #20 Silica sand 0.45-0.85mm, approximately 18 kg.
3. Ensure the O-ring is in place on the rim of the Bottom Tank. Make sure the O-ring and the rim of the Bottom Tank are clean without nicks, tears, scraps or sand. Attach the Top Tank to the Bottom Tank, place the Flange Clamp over the seam and turn the Nut clockwise to fasten it .
4. Attach the Control Valve to the Top Tank, ensuring the O-ring is in place on the rim of the
Top Tank. Make sure the O-ring and the rim of the Top Tank are clean without nicks, tears, scrapes or sand and that the vertical pipe of the Hub is inserted into the base of the
Control Valve.
5. Make sure Port C on the Control Valve is aligned with Port C on the Pump. Attach the Top
Flange Clamp and screw into position.
6. Attach the Piping to Pump Port C and to
Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping.
Section II: Hose Configuration for Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function. Your pool should be filled with water, make certain all of the pool’s Debris Screens (25)are fully submerged in water.
Please check if your product includes a T-Joint (25)(see Fig. E).
Please check if your product includes a T-Joint (27)(see Fig. E). If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A(see Fig.A-1)
1. Attach one end of the long hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Attach the T-joint(27) to the other end of the long hose(24).
3. Attach one end of both the short hoses(26) to the T-joint(27), and the other end to the pool’s Outlet “B”. Tighten the Hose clamps(23) of the T-joint(27).
4. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
Method B(see Fig.B-1)
1. Attach one Hose(24) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect the other end of the Hose(24) to the pool’s Outlet B.
3. Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen(25) supplied with your kit.
4. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool outlet are properly aligned.
• Screw the other Hose to Port D and place the opposite end in drain area.
• With the Hoses attached, you can proceed to fill the pool, refer to pool owner’s manual for filling instructions.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Unplug the sand filter and set the Control Valve to the Rinse function.
4. Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Unplug the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Unplug the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Fourth Hose
NOTE: It is imperative to check that the hydraulic connectors are not closed.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1. Detach the Hose from Port D.
2. Attach the Hose (24) to the Control Valve’s Port A; screw the threaded locking ring into position.
3. Connect the other end of Hose(24) to the pool’s Inlet A.
4. Remove the Stopper Plug from the pool’s Inlet A and insert Debris Screen ( 25 ) supplied with your kit.
5. With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE: It is important to ensure all elements: Hose, Debris Screen and pool Inlet are properly aligned.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
Sand Filter Maintenance
CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure
Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in
Section II and Section III: Backwash and Rinsing.
NOTE: The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
NOTE: We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Replace the Debris Screens with Stopper Plugs to prevent water from escaping.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Remove the Stopper Plugs and insert the Debris Screens
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
NOTE: Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage.
Allowing water to freeze will damage the sand filter and warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
Problems
Sand is flowing to the pool
TROUBLESHOOTING
Probable Causes
- Sand is too small
- Move the control valve from the backwash to the
filter function without stop the sand filter
- The level of the sand is too high
- The skimmer is broken
Solutions
- Recommend 0.45mm to 0.85mm #20 silica sand
- Stop the sand filter every time set the control valve
- Check if the level of the sand is between the marked “MAX” and “ MIN” on the hub
- Replace the skimmer
No water flow
- Stopper plugs are not removed
- The control valve is set to Closed
- The strainer is blocked
- Sand filter broken
- Remove the stopper plugs and insert the debris screens
- Set to filter function
- Clean the strainer
- Call for service
Excessive filter pressure
Control Valve leaks from the port D
Connectors leaks
- Dirty filter
- Calcified sand bed
- Insufficient backwashing
- The pressure gauge is broken
-
C o n t
T h e r g o l a s k e
V a t l i v s e b s r s o e t k e n b e t w e e n t w o f u n c t i o n s
- Washer of the connectors not in place
- Washer of the connectors broken
- O-ring on the hose connection is broken
- Loose Hoses
- Backwash
- Inspect sand and change if necessary
- Backwash until water runs clear
- Replace the pressure gauge
- Set to one function
- Replace the gasket
- Reposition the washer
- Replace the washer
- Replace the o-ring
- Tighten them
10
S-S-004293
11
S-S-004293
Limited BESTWAY
®
Manufacturer’s Warranty
The product you have purchased comes with a limited warranty. Bestway ® stands behind our quality guarantee and assures, through a replacement warranty, your product will be free from manufacturer’s defects.
To enact a warranty claim, this form must be completed and submitted with a copy of your purchase receipt to your local Bestway After Sales Center.
Please contact your local Bestway After Sales Center before sending any documents. They will provide full instructions of what is needed for your claim.
Bestway ® will not replace any products deemed to have been damaged due to negligence or having been used outside of the owner’s manual guidelines. Bestway’s warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within the user manual. This warranty applies only to products which have not been modified by any 3rd parties. The product must be stored and handled in accordance with the technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of incorrect voltage, excessive heat exposure, improper installation, improper wiring or testing, or improper storage.
Replacements and repairs don’t extend the duration of the warranty. The warranty start date is the date of sale shown on the original receipt/purchase invoice.
Please copy the Batch Number found on the body of the sand filter.
M/D
Batch
Number
Batch
Number
Batch
Number
Batch Number: Date of purchase:
TO: BESTWAY ® SERVICE DEPARTMENT Date: Customer Code Number:
FAX/E-MAIL/TEL: Please refer to your country according to the information found on the back cover or on our website: www.bestwaycorp.com
Please provide your address details in full. Note: Incomplete address details will result in delayed shipments.
Bestway reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
REQUIRED INFORMATION - PLEASE WRITE THE SHIPPING ADDRESS
Name:
Country:
Telephone:
Retailer:
Address:
City:
Fax:
Please Clearly Write Your Item Code:
Zip code:
Mobile:
E-mail:
Batch
Number
Item Code
SAND FILTER WITH OZONATOR MODEL #XXXXXX
SAND FILTER MODEL #XXXXXX
All drawings for illustration purpose only. Not to scale.
Problem description
Water leakage
Stopped working
Missing part - Please use the code for the missing part. This can be found in the owner's manual.
Other (Please describe)
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
Bestway reserves the right to request photographic evidence of defective parts, or to require sending the item for additional testing.
In order to best assist you, we request all information you provide to be complete.
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE: www.bestwaycorp.com
VIDEOS ARE ALSO AVAILABLE ON OUR BESTWAY CHANNEL ON YOU TUBE: www.youtube.com/user/BestwayService
12
S-S-004293
Advertisement