0MNACCSA3ENUC
0MNACCSA3ENUC
- ENGLISH -
INTRODUCTION
Thank you for choosing our product.
The accessories described in this manual are of the highest quality, carefully designed and built in
order to ensure excellent performance.
This manual contains detailed instructions on how to install and use the product.
It should be kept with care near the NetMan Plus, so that it can be consulted for information
on how to use and make the most of your device. IT SHOULD BE READ BEFORE YOU
START WORKING ON THE DEVICE.
Symbols used in this manual:
Warning
Indicates important information that must not be ignored.
Information
Provides notes and useful suggestions for the User.
SAFETY
This part of the manual contains SAFETY precautions that must be followed scrupulously.
 The device has been designed for professional use and is therefore not suitable for use in
the home.
 The device has been designed to operate only in closed environments. It should be
installed in rooms where there are no inflammable liquids, gas or other harmful substances.
 Take care that no water or liquids and/or foreign bodies fall into the device.
 In the event of a fault and/or impaired operation of the device, do not attempt to repair it but
contact the authorized service centre.
 The device must be used exclusively for the purpose for which it was designed. Any other
use is to be considered improper and as such dangerous. The manufacturer declines all
responsibility for damage caused by improper, wrong and unreasonable use.
-2-
- ENGLISH -
ENVIRONMENTAL PROTECTION
In the development of its products, the company devotes abundant resources to analysing the
environmental aspects.
All our products pursue the objectives defined in the environmental management system
developed by the company in compliance with applicable standards.
No hazardous materials such as CFCs, HCFCs or asbestos are used in this product.
When evaluating packaging, the choice of material has been made favouring recyclable materials.
Please separate the different material of which the packaging is made and dispose of all material in
compliance with applicable standards in the country in which the product is used.
DISPOSING OF THE PRODUCT
The device contains electronic PCBs and batteries which are considered TOXIC. When the
product reaches the end of its operating life, dispose of it in accordance with applicable local
legislation.
Disposing of the product correctly contributes to respecting the environment and personal health.
© No part of this manual may be reproduced without the prior written permission of the manufacturer.
The manufacturer reserves the right to modify the product described in this manual at any time and
without notice.
-3-
- ENGLISH -
CONTENTS
PRESENTATION __________________________________________________ 6
DESCRIPTION __________________________________________________________ 6
OPENING THE PACKAGING AND CHECKING THE CONTENTS __________________________ 7
NETWORK PORT ________________________________________________________ 8
MICRO-USB COMMUNICATION PORT __________________________________________ 8
NETWORK SERVICES _____________________________________________________ 8
SSH _____________________________________________________________________ 8
Serial network ____________________________________________________________ 8
Wake-on-LAN_____________________________________________________________ 8
HTTP ____________________________________________________________________ 9
SNMP ___________________________________________________________________ 9
UDP_____________________________________________________________________ 9
Modbus _________________________________________________________________ 9
FTP ____________________________________________________________________ 10
Email___________________________________________________________________ 11
Reports_________________________________________________________________ 12
UPS VALUES AND EVENTS HISTORY LOG ARCHIVE _______________________________ 13
Eventlog ________________________________________________________________ 13
Datalog _________________________________________________________________ 14
ENVIRONMENTAL SENSORS (OPTIONAL)_______________________________________ 15
Available sensors ________________________________________________________ 15
INSTALLATION AND CONFIGURATION ______________________________ 16
INSTALLATION OF NETMAN 202 PLUS ________________________________________ 16
CONFIGURATION _______________________________________________________ 16
Configuration via USB ____________________________________________________ 16
Configuration via ssh _____________________________________________________ 16
Saving the configuration and applying the changes ____________________________ 17
Start menu ______________________________________________________________ 17
Main configuration menu __________________________________________________ 18
IP config menu __________________________________________________________ 21
Time setting menu _______________________________________________________ 22
-4-
- ENGLISH -
Scheduled NTP menu _____________________________________________________ 24
UPS config menu ________________________________________________________ 25
Services 1 menu _________________________________________________________ 26
SNMPv1 config menu _____________________________________________________ 27
SNMPv1 community menu _________________________________________________ 27
Email config menu _______________________________________________________ 28
Email logic menu_________________________________________________________ 29
Miscellaneous menu ______________________________________________________ 30
Activation 1 menu ________________________________________________________ 31
Services 2 menu _________________________________________________________ 31
Wake-On-LAN address menu_______________________________________________ 32
Wake-On-LAN delay menu _________________________________________________ 32
Activation 2 menu ________________________________________________________ 33
Sensors Config menu _____________________________________________________ 33
I/O Sensors menu ________________________________________________________ 35
Threshold sens menu _____________________________________________________ 36
Security menu ___________________________________________________________ 37
Save and load menu ______________________________________________________ 39
Expert mode ____________________________________________________________ 39
Configuration of several devices____________________________________________ 43
MONITORING WITH HTTP _________________________________________________ 43
View HTTP ______________________________________________________________ 44
Setup HTTP _____________________________________________________________ 45
MODBUS TCP/IP PROTOCOL ______________________________________________ 48
FIRMWARE UPDATE _____________________________________________________ 53
TECHNICAL DATA ________________________________________________ 54
SPECIFICATIONS FOR THE CABLING OF THE NETWORK CABLE _______________________ 54
TECHNICAL SPECIFICATIONS _______________________________________________ 54
-5-
- ENGLISH -
PRESENTATION
DESCRIPTION
NetMan 202 plus is a device that allows UPS management through a LAN (Local Area Network);
the accessory supports all the main network protocols (SNMP v1 and v3, TCP/IP, HTTP and so
on) and is compatible with Ethernet 10/100Mbps IPv4/6 networks. The UPS can therefore be
integrated easily into medium and large-sized networks.
The device also records UPS values and events in the history log archive.
NetMan 202 plus

A: network port;

B: LED

C: Reset button

D: USB terminal

E: USB (reserved)

F:
Serial (reserved)
-6-
- ENGLISH -
OPENING THE PACKAGING AND CHECKING THE CONTENTS
After opening the packaging, first check the contents.
The packaging should contain:
NetMan 202 plus
USB cable
-7-
- ENGLISH -
NETWORK PORT
NetMan plus connects to 10/100 Mbps Ethernet networks by means of connector RJ45 (see
paragraph “Specifications for the cabling of the network cable”). The LEDs built into the connector
describe the status of the network:

Left LED:
1. on and yellow if the 10/100Mbps mode link is present
2. on and green if the 10Mbps mode link is present

Right LED:
1. on and yellow during transmission in full-duplex mode
2. on and green during transmission in half-duplex mode
MICRO-USB COMMUNICATION PORT
NetMan plus makes available an usb communication port through which it is possible to configure
NetMan plus (see paragraph “Configuration via RS-232 serial line”)
NETWORK SERVICES
NetMan plus implements a series of services based on the main network protocols. These services
can be activated or deactivated according to requirements (see paragraph “Configuration”). A brief
description for each of these is given below.
SSH
By means of a ssh client (available on all the main operating systems) a remote connection with
NetMan plus can be established to change its configuration (see paragraph “Configuration via
ssh”).
Serial network
It’s possible to enable a network connection together with Serial network compatible software (for
example UPSTools) for UPS event log download.
Wake-on-LAN
NetMan plus can send “Wake-on-LAN” command for remote computers boot.
-8-
- ENGLISH -
HTTP
Using the HTTP (Hyper Text Transfer Protocol), is possible to configure the NetMan plus and the
status of the UPS can be monitored by means of a web browser without having to install additional
software (see paragraph “Monitoring with HTTP”). All the most popular web browsers are
supported.
SNMP
SNMP (Simple Network Management Protocol) is a communication protocol that allows a client
(manager) to make requests to a server (agent). NetMan plus is an SNMP agent.
To exchange information, manager and agent use an addressing technique called MIB
(Management Information Base). There is an MIB file for each agent, defining which variables can
be requested and the respective access rights. The agent can also send messages (TRAP) without
a prior request from the manager, to inform the latter of particularly important events. SNMPv3 is
the evolution of SNMP and introduces new important features related to security. (See paragraph
“SNMPv3”).
UDP
UDP (User Datagram Protocol) is a low level network protocol that guarantees speed in the
exchange of data and low network congestion. It is the protocol used by the UPSMon software for
monitoring and control of the UPS.
The UDP connection uses the UDP 33000 port by default but can be configured on other ports
according to requirements.
Modbus
The UPS status can be monitored by means of the standard network protocol MODBUS TCP/IP.
This service is always active on the TCP port 502. The supported function are listed on section
“Modbus TCP/IP protocol”, together with the accessible registers.
-9-
- ENGLISH -
FTP
FTP (File Transfer Protocol) is a network protocol used for file exchange. NetMan plus uses this
protocol for two purposes:
1. download of files of the UPS values and events history log archive (Datalog and
Eventlog) with user “user”
2. download and upload of configuration files
3. firmware upgrade
In both cases a client FTP is required, configured with these parameters:

Host: hostname or NetMan plus IP address

User: see chapter “Users”

Password: current password (default configuration: “password”)
The connection can also be established using a web browser (all the most popular web browsers
are supported), by inserting the following address: ftp://user@<address.NetMan plus>, where
<address.NetMan plus> is replaced with the device’s real address. In this case a screen like the
following will be displayed.
Example of FTP connection
- 10 -
- ENGLISH -
Email
NetMan plus can send a notification e-mail if one or more alarm conditions occur. The e-mails can
be sent to up to three recipients and they can be sent for seven different kinds of alarm.
SMTP (Simple Mail Transfer Protocol) is the protocol used to send the e-mails. They are sent to an
SMTP server on port 25. For more details, see paragraph “Configuration”
Example of notification e-mail
- 11 -
- ENGLISH -
Reports
NetMan plus can send periodic e-mails with an attachment containing the files of the UPS values
and events history log archive.
This service can be used to periodically save the history log archives.
The “Email” service must be enabled in order to send reports; the reports are sent to all the
addresses configured for this service (for more details see paragraph “Configuration”).
Example of report e-mail
- 12 -
- ENGLISH -
UPS VALUES AND EVENTS HISTORY LOG ARCHIVE
NetMan plus records the UPS values (Datalog) and events (Eventlog) in a history log archive. The
data are saved to file in text format and can be read either by means of an electronic spreadsheet
(which allows the data to be ordered chronologically) or by any text editor. The format used to
record the date and time is of the type: MM/DD/YY HH:MM:SS
Eventlog
The Eventlog service is always active and records all relevant UPS events in the ‘event.log’ file.
The file can be downloaded via FTP or sent by e-mail using the “Email report” service. The data
are saved in circular list mode, thus the most recent data are saved by overwriting the oldest data.
Example of Eventlog
- 13 -
- ENGLISH -
Datalog
The Datalog service records the main UPS data in the ‘data.log’ file. The file can be downloaded
via FTP or can be sent by e-mail using the “Email report” service. The following data are
monitored:

Input voltage line 1

Input voltage line 2

Input voltage line 3

Input frequency

Output voltage line 1

Output voltage line 2

Output voltage line 3

Load on line 1

Load on line 2

Load on line 3
The interval of time between one recording and the next (Log frequency) can be configured by the
user (see paragraph “Miscellaneous Menu”). The data are saved in circular list mode, thus the
most recent data are saved by overwriting the oldest data. Data for up to 256 different points of
time can be recorded.
Example of Datalog
- 14 -
- ENGLISH -
ENVIRONMENTAL SENSORS (OPTIONAL)
Is possibile to connect to NetMan plus the environmental sensors for monitoring temperature,
humidity and digital input/output.
The information provided by these sensors can be showed with the UPS monitoring and control
software or with a web browser (the HTTP service must be active).
The values provided by the sensors may also be requested with SNMP according to the RFC 3433
standard. The MIB file is inside the bundled CD.
Available sensors



Temperature: detects the environmental temperature in °C.
Humidity & Temperature: detects the relative humidity in % and the environmental
temperature in °C.
Digital I/O & Temperature: detects the environmental temperature in °C and features a
digital input and a digital output.
It is possible to connect up to 3 environmental sensor to a NetMan plus (for sensor
installation please see the sensors’ manual).
- 15 -
- ENGLISH -
INSTALLATION AND CONFIGURATION
INSTALLATION OF NETMAN 202 PLUS
1.
Remove the cover of the UPS expansion slot by removing the two retaining screws.
2.
Insert NetMan 202 plus in the slot.
3.
Connect the device to the network by means of connector RJ-45 (see “Specifications for
the cabling of the network cable”)
4.
Secure Netman in the slot using the two screws removed previously.
CONFIGURATION
NetMan plus can be configured via usb or via ssh.
NetMan plus needs approx. 30 seconds to become operational from when it is powered
up; before this time the device may not respond to commands that are sent to it
Configuration via USB
To configure NetMan plus via USB, it is necessary to:

Connect, with the USB cable provided, the micro-USB port with the USB port of the PC

execute the software HyperNetman

press the “Enter” key of the PC

at the login prompt, enter “admin”

at the password prompt, enter the current password (default configuration: “admin”)
During password’s typing, no character is shown.
Once login has been effected, the screen of the start menu is displayed. From this screen it is
possible to access the various menus to change NetMan plus settings (see paragraph “Main
configuration menu” and following paragraphs).
Note: at the first login it is necessary to access with user admin (see chapter “Users”).
Configuration via ssh
To configure NetMan plus via ssh it is necessary to:

execute a ssh client on a PC connected in a network to NetMan plus set with the IP
address of the device to be configured

at the login prompt, enter “admin”

at the password prompt, enter the current password (default configuration: “admin”)
During password’s typing, no character is shown.
- 16 -
- ENGLISH -
Once login has been effected, the screen of the start menu is displayed. From this screen it is
possible to access the various menus to change NetMan plus settings (see paragraph “Main
configuration menu” and following paragraphs).
Note: at the first login it is necessary to access with user admin (see chapter “Users”).
Saving the configuration and applying the changes
In order to make the new configuration effective, it is necessary to save it in the flash memory; this
action automatically reboot the device (see paragraph “Menu Save and load”).
The clock settings (see paragraph “Time settings Menu”) become effective without saving.
Users
It is possible to access to NetMan 202 plus with various users:
 admin (password admin): user with right to modify the configuration
 fwupgrade (password fwupgrade): user with right to upgrade the firmware
 user (password user): user with right to read but not modify the configuration and the log
Start menu
/------------------------/
/
Netman 202 plus
/
/------------------------/
Setup..........:<-View status....:
Change password:
Service log....:
Expert mode....:
Press [ESC] for logout
SysVer. 0.0 - AppVer. 00.00
Select Setup to enter main configuration menu.
Select View status to see the status of the device (UPS).
Select Change password to modify the password.
Select Service log when requested by the service.
Select Expert mode for entering Expert mode (more information at paragraph “Expert mode”)
- 17 -
- ENGLISH -
Main configuration menu
The main configuration menu displays a screen like the following:
/------------------------/
/
NetMan plus
/
/------------------------/
IP config......:<-Time setting...:
UPS config.....:
Services 1.....:
Services 2.....:
Security.......:
Save and load..:
Press [Esc] to quit
Data from flash - On Line
From this main menu it is possible to access the various submenus, the function of each of which
is shown in the table below.
Menu
Function
IP config
To configure the network parameters
Time setting
To configure the internal clock
UPS config
To configure the type of UPS connected
Services 1
To activate and/or deactivate device services
Services 2
Security
To configure the password and access to the network
Save and load
To save a configuration thus making it effective in the event
of a device restart
- 18 -
- ENGLISH -
To move within this menu and the following menus, use the keys as described in the following
table; the arrow or the cursor shows the current selection.
Key
Function
Direction keys
(Arrow up, down, right, left)
To move the cursor within the menus
Tab
Goes on to next option
Choice of submenu
Enter (1)
Confirmation of characters entered
Exit main menu (2)
Esc
(1)
Return to previous menu
(1)
(2)
Some keys can have a different function depending on the menu.
To exit from a menu a confirmation (‘Y’ or ‘N’) is required after pressing the ESC key.
The screen also displays some messages describing the kind of configuration data displayed and
the status of the UPS. The meaning of these messages is described below.

Data from flash: means that the configuration has been loaded from the flash memory

Default data: means that the configuration has been reset to the default values
- 19 -
- ENGLISH -
Here is a graphical rapresentation of the menus and submenus:
- 20 -
- ENGLISH -
IP config menu
/------------------------/
/
IP config
/
/------------------------/
Hostname.......:ups_server
IP address/DHCP:dhcp
Netmask........:
Gateway........:
Primary DNS....:
Secondary DNS..:
Mailhost.......:
With this menu the main network parameters can be set as described in the following table.
Field
Parameters to be inserted
Hostname
Enter the NetMan plus host name
IP address/DHCP
Enter the IP address for a static IP; enter “DHCP” for a dynamic IP
Netmask
Enter the netmask to be used together with the static IP address
Gateway
Enter the name or the address of the network gateway
Primary DNS
Enter the name or the address of the preferred DNS to be used
Secondary DNS
Enter the name or the address of the alternative DNS to be used
Mailhost
Enter the name or the address of the SMTP server to be used to send emails. (1)
(1)
Ensure that the SMTP server accepts connections on port 25.
If a static IP address is assigned to the device, all the fields must be configured with the
network parameters. If a dynamic IP address is assigned, just enter ‘dhcp’ in the “IP
Address/DHCP” field and provide a hostname; all the other options should be ignored
because these are automatically configured with DHCP
- 21 -
- ENGLISH -
After pressing “ESC” and “Y” to confirm exit from the menu, a screen is displayed summarizing the
current settings (see image below). Press the “ENTER” key to return to the main menu. The
configuration must however be saved to make it effective after restart of the device (see “Save and
load” menu).
Hostname
:
Current IPv4 addr.:
Current IPv6 addr.:
Default IPv4 GW
:
Ethernet Address :
Primary DNS
:
Secondary DNS
:
DNS Timeout
:
DHCP Server
:
DHCP Enabled
:
DHCP Lease Ends
:
ups_server.mynetwork.domain
10.1.10.187/16 (255.255.0.0) (active)
fe80:0:0:0:260:35ff:fe02:4184/64 (active)
10.1.4.1
00:60:35:02:41:84
10.1.4.2
10.3.4.1
0 (ms)
10.1.5.1
true
Sun Jun 05 00:00:12 GMT 2005
(66 hr, 40 min, 38 seconds left)
Mailhost
: mymailserver
Restore From Flash: Not Committed
Time setting menu
/------------------------/
/
Time setting
/
/------------------------/
Set time.......:<-Set timezone...:
Sync with NTP..:
Scheduled NTP..:
From this menu the time and date of the device can be set as described in the following table.
Command
Description
Set time
To configure the time and date manually
Set timezone
To configure the time zone
Sync with NTP
To synchronize the clock with an NTP server
Scheduled NTP
To configure the scheduled NTP
- 22 -
- ENGLISH -
Pressing the “ENTER” key corresponding to the “Set time” command displays a screen like the one
shown below.
Current date is Wed Jun 15 08:09:40 GMT 2005
Insert new date and clock time in this form:
MMDDYYYYHHMMSS
06152005081000
Current date is Wed Jun 15 08:10:00 GMT 2005
Enter the date and time in the format shown, then press the ENTER key and then “ESC” to exit.
Pressing the “ENTER” key corresponding to the “Set timezone” command displays a screen where
is possible to modify the timezone. Examples of available timezones:
Europe/Rome
CET
GMT
Asia/Singapore
Etc/GMT+4
SystemV/HST10
Enter the time zone selected from those shown, then press the ENTER key and then “ESC” to exit.
Pressing the “ENTER” key corresponding to the “Sync with NTP” command displays a screen like
the one shown below.
Current date is Thu Jun 16 14:17:06 ECT 2005
Insert IP Address or host name of the NTP server to synchronize time:
leg
Synchronizing time to server: server.mycompany
New system time: 16 Jun 2005 12:17:00 GMT
Current date is Thu Jun 16 14:17:01 ECT 2005
Enter the name or the address of the NTP server with which the device is to be synchronized. In
this case the time has to be within the GMT time zone, thus it may be necessary to correct the
current time zone with the “Set timezone” command.
- 23 -
- ENGLISH -
Scheduled NTP menu
/------------------------/
/
Scheduled NTP
/
/------------------------/
NTP server.....:time_server
Sync only at...:13
hour (0 - 23)
Sync only at...:*
day of week (0 - 6) (Sunday=0 or 7) OR sun,mon,tue ...
Sync only at...:1
day of month (1 - 31)
Insert * where the value is not needed.
With this menu is possible to schedule the NTP synchronization. Is possible to specify the time and
frequency for performing a synchronization. For each field is possible to enter the precise condition
or leaving ‘*’ which means always. On the example above, synchronization will be performed every
1st day of month at 13:00, regardless of the day of week.
Field
Parameters to be inserted
NTP server
Enter the name or address of the NTP server
Sync only at (h)
Enter the hour when the synchronization should occur, or ‘*’
Sync only at (w)
Enter the day of week when the synchronization should occur, or ‘*’
Sync only at (m)
Enter the day of month when the synchronization should occur, or ‘*’
- 24 -
- ENGLISH -
UPS config menu
/------------------------/
/
UPS config
/
/------------------------/
PRTK Code......:GPSER11201XX
Name...........:ups3
UPS Address....:1
Serial number..:324321
With this menu the UPS parameters must be set as described in the following table, for the UPS to
be able to communicate correctly with the device.
Field
Parameters to be inserted
PRTK Code
Enter the PRTK code indicated at the back of the UPS(1)
Name
Enter the identifying name of the UPS
UPS Address
Insert 1
Serial number
Enter the UPS identification code
(1)
The PRTK code is formed of 12 alphanumeric characters.
- 25 -
- ENGLISH -
Services 1 menu
/------------------------/
/
Services 1
/
/------------------------/
SNMP config....:<-SNMP community.:
Email config...:
Email logic....:
Miscellaneous..:
Activation 1...:
With this menu the configuration screens of the various services can be accessed as described in
the following table.
Menu
Function
SNMP config
To configure the SNMP service
SNMP community
Email config
To configure the e-mail service
Email logic
Miscellaneous
To configure the other options
Activation 1
To configure the services to be activated
As well as being configured, the services must also be activated to function correctly (see
paragraph “Activation menu”). It is recommended to activate only the services used.
- 26 -
- ENGLISH -
SNMPv1 config menu
/------------------------/
/
SNMPV1 config
/
/------------------------/
Trap receiver 1:powernetguard
Trap receiver 2:192.168.5.96
Trap receiver 3:
Trap receiver 4:
Trap receiver 5:
Trap receiver 6:
Trap receiver 7:
With this menu the IP addresses to which traps are sent can be configured. Traps are SNMP
messages that are sent to an SNMP manager for alarm notification.
Traps can be sent to seven different hosts.
SNMPv1 community menu
/------------------------/
/
SNMPV1 community
/
/------------------------/
Get community..:public
Set community..:private
Trap community.:public
With this menu the protection password of the SNMP messages (SNMP Communities) can be
configured as described in the following table.
Field
Parameters to be inserted
Get community
Enter the community for read access
Set community
Enter the community for write access
Trap community
Enter the community for traps
- 27 -
- ENGLISH -
Email config menu
/------------------------/
/
Email config
/
/------------------------/
Email address 1:myself@mycompany.com
Email address 2:service@service.com
Email address 3:anotheremail@mycompany.com
Sender address.:NetMan_plus
Customer.......:MyCustomer
Report interval:01-05:10
DD-HH:MM
User name......:User 1
Password.......:Password
This menu may be used to configure the addresses to which to send the alarm notification and
report e-mails and other parameters of the e-mail service as described in the following table.
Field
Parameters to be inserted
Email address 1
Email address 2
Email address 3
Sender address
Customer
Report interval
User name
Password
(1)
Enter the e-mail addresses to which to send the alarm notifications and
reports (see note).
Enter the address from which the e-mails are sent. (1)
Enter an identifying string; this additional information is included in the email.
Enter the delay, measured in days, between the sending of one report email and the next by using exactly 2 figures, followed by a line, an finally
by the hour and minutes on which the email should be sent.
If the server requires authentication, insert the “User name”.
If the server requires authentication, insert the password.
do not use the “space” character in this field
After inserting the data and pressing the “ESC” key to exit from the menu, the service can be
tested by pressing the “T” key. If the test is performed, a “@” is displayed and a test email is sent
to all the configured email addresses. After this the previous menu is shown.
Report e-mails are sent to all the addresses inserted; for alarm notification e-mails see
paragraph “Email logic menu”.
- 28 -
- ENGLISH -
Email logic menu
/------------------------/
/
Email logic
/
/------------------------/
Email 1
Email 2
Email 3
Logic:
UPS Lock.......:
X<--
0
0
And
Ovrload/Ovrtemp:
X
0
0
And
UPS Failure....:
X
0
0
And
On bypass......:
X
0
0
And
Battery work...:
X
0
0
And
Battery low....:
X
0
0
And
Communic lost..:
X
0
0
And
With this menu it can be established to which addresses the e-mails will be sent when certain
events occurs. One or more addresses can be associated with each event and in the latter case,
when the event occurs, notification e-mails will be sent to all the addresses associated with it.
Use the ENTER key to change the selected configuration (“X” or “0”).

X: when the event occurs, NetMan plus sends a notification e-mail to the corresponding
addresses (see “Email logic menu” to set the addresses);

0: when the event occurs, NetMan plus does not send a notification e-mail to the
corresponding addresses;
The following table describes the meaning of the events. These can vary depending on the UPS
connected.
Event
Meaning
UPS Lock
UPS is locked
Ovrload/Ovrtemp
UPS in overload or in overtemperature
UPS Failure
Failure of the UPS
On bypass
Operation from bypass
Battery work
Operation from battery
Battery low
Battery low
Communic lost
Communication between the UPS and the device has been interrupted
SENTR level 2
SENTR level 3
Presence of an internal UPS failure (this condition emulates the level
of modem alarm for UPSs of the SENTR type)
Presence of a failure in the UPS, excluding those envisaged in the
previous point (this condition emulates the level of modem alarm for
UPSs of the SENTR type)
- 29 -
- ENGLISH -
Miscellaneous menu
/------------------------/
/
Miscellaneous
/
/------------------------/
Log frequency..:5
sec
UDP Port.......:33000
sysContact.....:Administrator
sysName........:My Server
sysLocation....:new building
With this menu further device parameters can be configured as described in the following table.
Field
Parameters to be inserted
Log frequency
Enter the delay, measured in seconds, between one data log and the next
(see paragraph “Datalog”)
UDP Port
Enter the port where the UDP service is started (1)
sysContact
sysName
Enter the string to be associated with these SNMP variables
sysLocation
(1)
This port must be the same as configured in the UPSMon software
- 30 -
- ENGLISH -
Activation 1 menu
/------------------------/
/
Activation 1
/
/------------------------/
Enable telnet..:[ON/off]<--
Enable FTP.....:[ON/off]
Enable HTTP....:[ON/off]
Enable DataLog.:[ON/off]
Enable Modem Tx:[on/OFF]
Enable Modem Rx:[on/OFF]
Enable SNMP....:[ON/off]
Enable Email...:[ON/off]
Enable UDP.....:[ON/off]
Enable Report..:[ON/off]
With this menu the services implemented in NetMan plus can be activated or deactivated:
Use the ENTER key to change the selected configuration (“ON” or “OFF”).

ON (green characters): service active

OFF (red characters): service not active
It is recommended to activate only the services used.
Services 2 menu
/------------------------/
/
Services 2
/
/------------------------/
WakeOnLan addr.:<-WakeOnLan delay:
Activation.2...:
Sensors config :
I/O Sensors....:
Threshold sens.:
With this menu the configuration screens of the various services can be accessed as described in
the following table.
Menù
Funzione
WakeOnLan addr.
WakeOnLan delay
Activation 2
To configure the Wake-on-LAN service
To configure the services to be activated
Sensors. config
I/O Sensors
To configure the environmental sensors
Threshold sens
As well as being configured, the services must also be activated to function correctly (see
paragraph “Activation 2 menu”). It is recommended to activate only the services used.
- 31 -
- ENGLISH -
Wake-On-LAN address menu
/------------------------/
/ Wake-on-LAN address /
/------------------------/
MAC Address 1..:00-12-3F-2B-F6-6F
MAC Address 2..:aa-bb-cc-dd-ee-ff
MAC Address 3..:00-00-00-00-00-00
MAC Address 4..:
MAC Address 5..:
MAC Address 6..:
MAC Address 7..:
MAC Address 8..:
With this menu is possible to insert up to 8 MAC address to execute Wake-on-LAN.
Please make sure that your PC supports this function, and that it is correctly configured.
Wake-On-LAN delay menu
/------------------------/
/ Wake-on-LAN delay
/
/------------------------/
Address 1 delay:2
sec.
Address 2 delay:40
sec.
Address 3 delay:2
sec.
Address 4 delay:
sec.
Address 5 delay:
sec.
Address 6 delay:
sec.
Address 7 delay:
sec.
Address 8 delay:
sec.
With this menu is possible to insert the delay times for each Wake-on-LAN.
- 32 -
- ENGLISH -
Activation 2 menu
/------------------------/
/
Activation 2
/
/------------------------/
Enable Serial N:[ON/off]<-Enable Sensors.:[ON/off]
Enable WOL
:[on/OFF]
With this menu the services implemented in NetMan plus can be activated or deactivated:
Use the ENTER key to change the selected configuration (“ON” or “OFF”).

ON (green characters): service active

OFF (red characters): service not active
It is recommended to activate only the services used.
Sensors Config menu
To enter on the “Sensors config” menu is necessary to enable the “Sensors” service
(Activation 2 menu) and to save the configuration (Save and load menu).
Sensors Devices
Press [C] to change sensors, [E] to exit
Enter on the “Config sensor” menu, connect the first sensor and press “C”. After some instants the
device will be recognized and the device will be given an identifier number [1]. Connect the next
sensor, if present, and press “N”. After some instants the device will be recognized and the device
will be given an identifier number [2]. Repeat the procedure for all the sensors and when the
configuration is finalized press “Y”.
Sensors Devices
[1] Sensor Digital I/O
+ Temperature (140000009A204C28)
+ Digital I/O (220000003B8C9F12)
+ 1 Input
+ 1 Output
[2] Sensor Digital I/O
+ Temperature (510000009A154228)
+ Digital I/O (BB0000003BA2FF12)
+ 1 Input
+ 1 Output
[3] Sensor Temperature (F100000013BE0628)
+ Temperature
[4] Sensor Temperature (6C0000009F6D6128)
+ Temperature
[5] Sensor Humidity (4D00000083FF3326)
+ Humidity
+ Temperature
Press [Y] to confirm, [N] to insert a new sensor
For proper working of the devices, it is necessary to add just one device for each iteration
and wait that it is recognized by NetMan plus.
- 33 -
- ENGLISH -
Example: how to connect a Temperature sensor, a Humidity & Temperature sensor and a Digital
I/O & Temperature sensor in exactly this order.
Sensors Devices
Press [C] to change sensors, [E] to exit
Connect the first sensor (Temperature), and press “Y”.
Sensors Devices
[1] Sensor Temperature (F100000013BE0628)
+ Temperature
Press [Y] to confirm, [N] to insert a new sensor
Wait until the first sensor is identified and then connect the second sensor (Humidity &
Temperature), and press “N”.
Sensors Devices
[1] Sensor Temperature (F100000013BE0628)
+ Temperature
[2] Sensor Humidity (4D00000083FF3326)
+ Humidity
+ Temperature
Press [Y] to confirm, [N] to insert a new sensor
Wait until the second sensor is identified and then connect the third sensor (Digital I/O &
Temperature), and press “N”.
Sensors Devices
[1] Sensor Temperature (F100000013BE0628)
+ Temperature
[2] Sensor Humidity (4D00000083FF3326)
+ Humidity
+ Temperature
[3] Sensor Digital I/O
+ Temperature (510000009A154228)
+ Digital I/O (BB0000003BA2FF12)
+ 1 Input
+ 1 Output
Press [Y] to confirm, [N] to insert a new sensor
Press “Y” to confirm.
- 34 -
- ENGLISH -
I/O Sensors menu
/------------------------/
/
Output
/
/------------------------/
UPS Lock.......:
-<--
Ovrload/Ovrtemp:
-
UPS Failure....:
-
On bypass......:
4
Battery work...:
3
Battery low....:
-
Communic lost..:
-
Input sensor...:
1
Press [Esc] to quit
With this menu is possibile to associate a digital output of the installed sensors to one or more
events of the UPS. The output will be closed when the associated event happens.
Press ENTER to select the output.
The identification number is the same which is associated to the sensor during
installation.
The following table describes the meaning of the events. These can vary depending on the UPS
connected.
Event
Description
UPS Lock
UPS is locked
Ovrload/Ovrtemp
UPS in overload or in overtemperature
UPS Failure
Failure of the UPS
On bypass
Operation from bypass
Battery work
Operation from battery
Battery low
Battery low
Communic lost
Communication between the UPS and the device has been interrupted
The “Input sensor” event allows to associate a digital output with the digital input of the Digital I/O &
Temperature sensor which is installed with the lowest identification number (the first that was
detected during configuration). The state of the input (open/closed) is reported to the output of
the selected sensor.
- 35 -
- ENGLISH -
Threshold sens menu
/------------------------/
/
Threshold sens
/
/------------------------/
Temperature max:100 degree C
Temperature min:20
degree C
Temp hysteresis:5
degree C
Humidity Max...:100 % RH
Humidity Min...:0
% RH
Hum hysteresis.:5
% RH
Press [Esc] to quit
With this menu is possible to set the alarm threshold for humidity and temperature sensors. When
exceeding the threshold, a SNMP alarm trap is sent. A trap is sent every minute until the alarm is
active. The alarm ceases to be active when the outbound value (temperature or humidity) is under
the threshold with the degree of hysteresis that is configured. (Example: with a maximum
temperature of 30°C and 3°C hysteresis, the alarm is activated when the temperature reaches
30°C and is removed when the temperature at 27°C).
Menu
Significato
Temperature max
Threshold for maximum temperature
Temperature min
Threshold for minimum temperature
Temp hysteresis
Hysteresis for removing temperature alarm (high and low)
Humidity max
Threshold for maximum humidity
Humidity min
Threshold for minimum humidity
Hum hysteresis
Hysteresis for removing humidity alarm (high and low)
- 36 -
- ENGLISH -
Security menu
/------------------------/
/
Security
/
/------------------------/
UDP Password...:<-Firewall.......:
From this menu the setup password, the UDP password and the firewall can be configured as
described in the following table.
Menu
Function
UDP Password
To change the password used for UDP/UPSMon communication (2)
Firewall
To configure access from the network
(1)
(2)
default configuration: “password”
this password must be the same as the one used by the UPSMon software
Pressing the ENTER key corresponding to the “UDP Password” command displays a screen like
the one shown below.
Enter the new UDP password:
Confirm the new UDP password:
Enter, as requested, the new password.
- 37 -
- ENGLISH -
Pressing the ENTER key corresponding to the “Firewall” command displays a screen like the one
shown below.
/------------------------/
/
Firewall
/
/------------------------/
Access IP 1....:*.*.*.*
Access IP 2....:0.0.0.0
Access IP 3....:0.0.0.0
Access IP 4....:0.0.0.0
Access IP 5....:0.0.0.0
Access IP 6....:0.0.0.0
Access IP 7....:0.0.0.0
With this menu the IP addresses or hostnames of the devices enabled for communication with
NetMan plus can be configured. The character “*” can be used for one or more fields of the IP
address to indicate that all values between 0 and 255 are accepted in that field. The following table
provides some possible configuration examples.
IP Access
Description
*.*.*.*
All the devices present on the network are enabled to communicate with
NetMan plus (default configuration)
10.1.10.*
The devices with addresses between 10.1.10.0 and 10.1.10.255 are
enabled to communicate with NetMan plus
myserver.mydomain Hostname of the device enabled to communicate with NetMan plus
- 38 -
- ENGLISH -
Save and load menu
/------------------------/
/
Save and load
/
/------------------------/
Apply changes..:<-Revert changes.:
Reset default..:
With this menu the configuration can be saved to make it effective or to load other configurations
as described in the following table.
Function
Description
Apply changes
Saves the configuration in flash memory and then automatically restarts to
make the changes effective
Revert changes
Cancels the changes and reloads the last saved configuration (excluding the
the clock -Time setting- configurations)
Reset default
Loads the default configuration
(1)
see paragraph “Configuration of several devices”
Expert mode
Expert mode enables the configuration of advanced parameters that should be set by skilled
technicians. These commands are supported:
help
prints the help
get
shows all values
set <VAR> <VALUE> set VAR to VALUE
reboot
reboot the NetMan
exit
closes the connection
- 39 -
- ENGLISH -
SNMPV3 CONFIGURATION
For configuring SNMPv3 access, is necessary to edit snmp.conf. This file can be downloaded and
uploaded with FTP with user “admin” (default password is “admin”).
If this file is not present, SNMPv1 will be used.
Each line of the file is parsed by netman 202 plus and must begin with one of these keyword:






#: for comment, the line is skipped.
addUser: for adding a new user and setting the passwords
addGroup: for putting a user into a group
addAccessEntry: for enabling access privileges to a group
addView: for adding privileges
addManager: for adding SNMP Manager which will receive SNMP traps.
The correct syntax for addUser is:
addUser <userName> <authProtocol> <privProtocol> <authPassword> <privPassword>
<userName> is the name of the user.
<authProtocol> is the protocol for authentication of this user during SNMP sessions. Possible
values are:



noauth (no authentication will be used)
md5 (MD5 will be used for authentication)
sha (SHA will be used for authentication)
<privProtocol> is the protocol for privacy of this user during SNMP sessions. Possible values are:


nopriv (no privacy will be used)
des (DES will be used for privacy)
<authPassword> is the password for authentication. It must be set to * when not used.
<privPassword> is the password for privacy. It must be set to * when not used.
The correct syntax for addGroup is:
addGroup <securityModel> <userName> <groupName>
<securityModel> is the security model. When using authentication and/or privacy, securityModel
must be USM. Possible values are:



USM (User-based Security Model with SNMPv3)
v2 (SNMPv2)
v1 (SNMPv1)
<userName> is the name of the user, must match one of the user name defined with addUser.
<groupName> is the name of the group.
Please note that a userName can be assigned to only one group.
The correct syntax for addAccessEntry is:
addAccessEntry <groupName> <contextName> <securityModel> <securityType> <contextMatch>
<readView> <writeView> <notifyView>
<groupName> is the name of the group to which this access right applies, must match one of the
group name defined with addGroup.
<contextName> is the name of the context.
<securityModel> is the security model that must be used in order to gain access to this access
right, must match the security model defined with addGroup.
- 40 -
- ENGLISH -
<securityType> is the minimum security level that must be used to gain access to this access right.
Possible values are:



noauthnopriv (no authentication and no privacy)
authnopriv (authentication but no privacy)
authpriv (authentication and privacy)
<contextMatch> the type of match required. Possible values are:


exact (the context name must exactly match the value in contextName)
prefix (the context name must match the first few starting characters of the value in contextName)
<readView> the authorized MIB view name used for read access, must match one of the view
name.
<writeView> the authorized MIB view name used for write access, must match one of the view
name.
<notifyView> the authorized MIB view name used for notify access, must match one of the view
name.
The correct syntax for addView is:
addView <viewName> <subtree> <mask> <included>
<viewName> is the name of the view.
<subtree> is the OID subtree which when combined with the corresponding instance of MASK
defines a family of view subtrees.
<mask> the mask for filtering OID.
<included> the OID can be included or excluded. Possible values are:


included (for including)
excluded (for excluding)
The correct syntax for addManager is:
addManager <security> <ipAddress> <credentials> <securityType>
<security> is the security type for the notification. Possible values are:



USM (User-based Security Model with SNMPv3)
V2 (SNMPv2)
v1 (SNMPv1)
<ipAddress> is the IP address of the SNMP manager.
<credentials> is either the user name (when using USM security) or the trap community (when
using v1 security)
<securityType> is either:


noauthnopriv (for SNMPv1 and SNMPv2)
authpriv (for SNMPv3)
addManager do not allow duplicate entries (one ipAddress can receive only one trap).
- 41 -
- ENGLISH -
A sample snmp.conf is provided; the default users authorized are:
Name
Auth
protoc
ol
Priv
protoc
ol
Auth
passwo
rd
Priv
passwo
rd
unsecureUs
er
Noauth
MD5
SHA
MD5DES
SHADES
md5
Sha
md5
Sha
nopriv
nopriv
nopriv
des
des
MD5UserAuthPassw
ord
SHAUserAuthPassw
ord
MD5DESUserAuthPassw
ord
SHADESUserAuthPassw
ord
MD5DESUserPrivPassw
ord
SHADESUserPrivPassw
ord
The SNMP agent will send SNMPv3 trap to address 10.2.10.1.
- 42 -
- ENGLISH -
Configuration of several devices
If several devices requiring similar configuration parameters are to be installed, configure the first
card, connect via FTP with the admin user, download the configuration file, and upload them on all
devices to be configured via FTP.
Example of FTP connection for multiple installations
MONITORING WITH HTTP
The HTTP service uses TLS (transport layer security) in order to provide cryptographic security.
However, the certificate used is self-signed and therefore the web browser may prompt a security
alert.
Once the hostname or the NetMan plus IP address has been inserted in your web browser, the
following screen will be shown. From here is possible to view the status of the UPS and configure
the NetMan plus.
- 43 -
- ENGLISH -
View HTTP
It is possible to view the status of the UPS without entering the login by pressing “View”.
By pressing “View”, a screen like the one shown below will be displayed, with the main UPS
operating data.
- 44 -
- ENGLISH -
Besides the “Main” view, is possible to switch the view from the “Status” menu which includes also
the “Nominal” view and the “Sensor” view (for viewing external sensors).
It is also possible to download the event.log and data.log (if available) from the “Log” menu.
Setup HTTP
For configuration it will be requested to enter the log in and password. These are the same of ssh
config and are required to modify the configuration.
When inserting a valid log in and password is possible to configure the netman.
- 45 -
- ENGLISH -
The settings are the same of ssh config.
The user is logged out after 3 minutes of inactivity, or when the “Logout” is selected.
By pressing submit the data for the current view is sent to the netman; by pressing reset the data
for the current view is discarded.
With HTTP each view is configured separately, therefore is required to press submit for each (for
example, when changing device config and ip config is required to press submit on device config
and on ip config).
The changes becomes effective on next reboot.
- 46 -
- ENGLISH -
Example of display via HTTP
The following buttons are found on the left-hand side of the page:

Nominal Data: opens a page displaying the nominal values of the UPS, the list of active
alarms and a diagram of UPS operation (see image on next page)

FTP: opens an FTP session (see paragraph ”FTP”)

About: opens a page with copyright information
- 47 -
- ENGLISH -
MODBUS TCP/IP PROTOCOL
This service is always active on the TCP port 502. The supported function are listed below,
together with the accessible registers.
SUPPORTED FUNCTION
SUPPORTED
FUNCTION
1
2
3
4
6
16
(0x01)
(0x02)
(0x03)
(0x04)
(0x06)
(0x10)
FUNCTION DESCRIPTION
BIT READING
REGISTERS READING
SINGLE REGISTER WRITING
MULTIPLE REGISTER WRITING
- 48 -
ACCESSIBLE DATA
AREA
STATES
STATES
ALL
ALL
COMMANDS
COMMANDS
- ENGLISH -
UPS: TABLES OF STATES, MEASUREMENTS, NOMINAL DATA AND COMMANDS
REGISTER
(1)
BIT
(2)
UPS - STATES
NUMBER
ADDRESS
Test in progress[0=No / 1=YES]
Shutdown active [0=No / 1= YES]
1
0
Battery charged[0=No / 1= YES]
Battery charging[0=No / 1= YES]
Bypass bad[0=No / 1= YES]
Normal operation[0=No / 1= YES]
On bypass[0=No / 1= YES]
Battery low[0=No / 1= YES]
Battery working[0=No / 1= YES]
UPS locked[0=No / 1= YES]
Output powered[0=No / 1= YES]
(1)
(2)
2
1
3
2
4
3
58
47
Input Mains present[0=No / 1= YES]
Alarm temperature[0=No / 1= YES]
Alarm overload[0=No / 1= YES]
UPS failure[0=No / 1= YES]
Communication lost with UPS[0=No / 1= YES]
NUMBER
ADDRESS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1728
29
30
31
32
3348
4963
64
65128
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1627
28
29
30
31
3247
4862
63
64127
The register number n must be addressed n-1 in the data packet
The bit number n must be addressed n-1 in the data packet.
REGISTER
(1)
UPS - MEASUREMENTS
NUMBER
ADDRESS
911
12
13
14
15
16
17
18
1921
22
23
24
25
26
27
28
2931
32
810
11
12
13
14
15
16
17
1820
21
22
23
24
25
26
27
2830
31
UNIT
Input mains star voltage V1
Input mains star voltage V2
Input mains star voltage V3
Input current phase L1
Input current phase L2
Input current phase L3
Input frequency
V
V
V
0.1*A
0.1*A
0.1*A
0.1*Hz
Bypass mains star voltage V1
Bypass mains star voltage V2
Bypass mains star voltage V3
Bypass frequency
Output star voltage V1
Output star voltage V2
Output star voltage V3
V
V
V
0.1*Hz
V
V
V
Output current phase L1
0.1*A
- 49 -
- ENGLISH -
33
34
35
36
37
38
39
40
41
42
43
44
4547
48
49
50
51
52
53
54
5558
59
60
61
62
63
64
6572
(1)
32
33
34
35
36
37
38
39
40
41
42
43
4446
47
48
49
50
51
52
53
5457
58
59
60
61
62
63
6471
Output current phase L2
Output current phase L3
Output peak current phase L1
Output peak current phase L2
Output peak current phase L3
Load phase L1
Load phase L2
Load phase L3
Output active power phase L1
Output active power phase L2
Output active power phase L3
Output frequency
0.1*A
0.1*A
0.1*A
0.1*A
0.1*A
%
%
%
0.1 kW
0.1 kW
0.1 kW
0.1*Hz
Battery voltage
Positive battery voltage
Negative battery voltage
Battery current
Remaining Battery Capacity
0.1*V
0.1*V
0.1*V
0.1*A
%
Remaining back-up time
Total output energy (32 bit)
Internal UPS temperature
Sensor 1 temperature
Sensor 2 temperature
Minutes
Least Significant Register
Most Significant Register
0.1 kWh
°C
°C
°C
The register number n must be addressed n-1 in the data packet.
Some measures may not be available for all the UPS. In this case, the relative register
remains at 0xFFFF value.
- 50 -
- ENGLISH -
REGISTER
(1)
UPS – NOMINAL DATA
NUMBER
ADDRESS
7377
78
79
80
8183
84
85
86
87112
7276
77
78
79
8082
83
84
85
86111
REGISTER
Output nominal voltage (star)
Output nominal frequency
Output nominal power
V
0.1*Hz
100*VA
Battery nominal capacity (battery expansion included)
Battery benches
Battery type
Ah
(1 or 2)
Integer
(1)
UPS - COMMANDS
NUMBER
ADDRESS
113
114
115
116
117
118
112
113
114
115
116
117
REGISTER
(2)
Command code
Shutdown delay time
Restore delay time
Command result
(2)
(3)
UNIT
Integer
Seconds
Minutes
(3)
Integer
(1)
DIAGNOSTIC
(1)
UNIT
NUMBER
ADDRESS
119
120
118
119
Counter of processed correct messages
Counter of processed NOT correct messages
The register number n must be addressed n-1 in the data packet.
Refer to “Command codes” paragraph
Command result = Command code if command is handled from the UPS
Command result = Command code + 100 if command is NOT handled from the UPS
Command result = 0 if Command code is wrong
- 51 -
UNIT
Integer
Integer
- ENGLISH -
REGISTER
(1)
SPECIAL FLAGS (SENTR UPS)
NUMBER
ADDRESS
121
122
123
124
125
126
127
128
120
121
122
123
124
125
126
127
REGISTER
Byte 1 of “s = xx..” code / Byte 2 of “s = ..xx” code
Byte 1 of “c = xx..” code / Byte 2 of “c = ..xx” code
Byte 1 of “b = xx..” code / Byte 2 of “b = ..xx” code
Byte 1 of “r = xx..-..” code / Byte 2 of “r = ..xx-..” code
Byte 3 of “r = ....-xx” code / Byte 1 of “i = xx..-..” code
Byte 2 of “i = ..xx-..” code / Byte 3 of “i = ....-xx” code
Byte 1 of “a = xx..-....” code / Byte 2 of “a = ..xx-....” code
Byte 3 of “a = ....-xx..” code / Byte 4 of “a = ....-..xx” code
(2)
NUMBER
ADDRESS
129
130÷131
128
129÷130
Firmware version
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
In order to decode these registers, please refer to the UPS manual.
UPS: COMMANDS CODES
CODE
(0x0001)
(0x0002)
(0x0003)
(0x000C)
(0x0014)
(0x0016)
UNIT
Integer
The register number n must be addressed n-1 in the data packet.
1
2
3
12
20
22
UNIT
(1)
NETMAN DATA
(1)
(2)
COMMAND
Command Shutdown
Command Shutdown and Restore
Delete Command (code 1, 2, 12)
UPS on Bypass
Test Battery
Test Panel
- 52 -
- ENGLISH -
FIRMWARE UPDATE
The NetMan 202 plus firmware can be updated via FTP.
Connect via FTP with the user “fwupgrade” (password “fwupgrade”) and copy the updated
firmware. Then restart the card, by pressing the reset button or via SSH enter into the menu with
user "admin" and select "Save changes".
- 53 -
- ENGLISH -
TECHNICAL DATA
SPECIFICATIONS FOR THE CABLING OF THE NETWORK CABLE
To connect the device to the Ethernet (10Base-T) or Fast Ethernet (100Base-T) network, a UTP
(Unshielded Twisted Pair) or STP (Shielded Twisted Pair) cable with RJ45 connectors is required.
The cable must conform to the standard IEEE 802.3u 100Base-T with 2 pairs of UTP cables of
category 5 or higher. The cable between the adaptor and the hub must not be more than 100m and
not less than 2.5m.
NETWORK CABLE CONNECTIONS
Signal
Pin # to Pin #
TX+
11
TX-
22
RX+
33
RX-
66
Pins 1 and 2 must be connected to one twisted pair, pins 3 and 6 to another.
TECHNICAL SPECIFICATIONS
NetMan 202 plus
Input voltage
[Vdc]
12
Maximum input current
[mA]
200
Operating temperature
[°C]
0 ÷ +40
Storage temperature
[°C]
-5 ÷ +50
Operating relative humidity
[%]
80 (max)
Storage relative humidity
[%]
90 (max)
POWER SUPPLY
ENVIRONMENTAL
CONDITIONS
- 54 -
0MNACCSA3ENUC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising