Siemens EM11 I/O board User Manual
Below you will find brief information for I/O board EM11. The EM11 I/O board is used for digitizing (analog inputs with A/D or V/F/D converters) and for the output of analog voltage signals, for the input of binary signals (speed), for input/output (binary I/O) and display (LED) of binary information. It features four channels with A/D conversion, four channels with V/F and F/D conversion, two channels with D/A conversion, one channel for actual speed value and position encoding with inputs for two tracks plus the zero marking pulse, 16 binary inputs and 8 binary outputs, and 16 LED's on the front panel.
Advertisement
Advertisement
SIMADYN D
Digital Control System
I/O board EM11
User Manual
Edition 05.95
DK-Nr. 233141
User Manual, I/O board EM11
Edition
1
2
I/O board EM11
I/O board EM11
Edition status
03.91
05.95
Copying of this document and giving it to others and the use or communication of the contents thereof is forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.
We have checked the contents of this Manual to ensure that they coincide with the described hardware and software. However, deviations cannot be completely ruled-out, so we cannot guarantee complete conformance. However, the information in this document is regularly checked and the necessary corrections included in subsequent editions. We are thankful for any recommendations or suggestions.
Contents
Contents
Warning information................................ ................................ ................................ .................... 1
1. Description................................ ................................ ................................ .............................. 3
1.1. New functions ................................ ................................ ................................ ..........4
1.1.1. RIC: *RDY-INTERNAL-CONTROL ................................ ............................ 4
1.1.2. Speed Value Inputs ................................ ................................ ................... 4
1.1.3. Monitor Input of the Speed Value Connector................................ ..............5
1.1.4. Monitor Register for the Speed Value Input................................ ................5
1.1.5. Binary outputs................................ ................................ ............................ 6
1.1.6. Analog outputs................................ ................................ ........................... 6
2. Board Design ................................ ................................ ................................ .......................... 7
3. Application Notes ................................ ................................ ................................ .................... 8
4. Technical Specification ................................ ................................ ................................ ...........10
5. Connector Pin Assignments of the EM 11 ................................ ................................ ...............13
5.1. Pin Assignments for Actual Speed Value, Connector X5................................ ..........13
5.2. Pin Assignments of the Analog Inputs and Outputs, Connector X6........................... 13
5.3. Pin Assignments for the Binary Inputs/Outputs, Connector X7................................ .14
6. STRUC-L menu ................................ ................................ ................................ ...................... 15
7. Miscellaneous ................................ ................................ ................................ ......................... 16
7.1. Appendices................................ ................................ ................................ ..............16
7.1.1. Diagrams................................ ................................ ................................ ...16
7.1.2. Drawings ................................ ................................ ................................ ...18
8. ECB instructions................................ ................................ ................................ ...................... 19
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
Warning information
Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Warning information
N O T E !
The information in this Manual does not purport to cover all details or variations in equipment, nor to provide for every possible contingency to be met in connection with installation, operation or maintenance.
Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, please contact your local Siemens office.
Further, the contents of this Manual shall not become a part of or modify any prior or existing agreement, committment or relationship. The sales contract contains the entire obligation of Siemens. The warranty contained in the contract between the parties is the sole warranty of Siemens. Any statements contained herein do not create new warranties nor modify the existing warranty.
Warning information
W A R N I N G !
Electrical equipment has components which are at dangerous voltage levels.
If these instructions are not strictly adhered to, severe bodily injury and material damage can result.
Only appropriately qualified personnel may work on this equipment or in its vicinity.
This personnel must be completely knowledgeable about all the warnings and service measures according to this User Manual.
The successful and safe operation of this equipment is dependent on proper handling, installation, operation and maintenance.
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
1
Warning information
Definitions
*
QUALIFIED PERSONNEL
For the purpose of this User Manual and product labels, a „Qualified person“ is someone who is familiar with the installation, mounting, start-up and operation of the equipment and the hazards involved. He or she must have the following qualifications:
1. Trained and authorized to energize, de-energize, clear, ground and tag circuits and equipment in accordance with established safety procedures.
2. Trained in the proper care and use of protective equipment in accordance with established safety procedures.
3. Trained in rendering first aid.
*
DANGER
For the purpose of this User Manual and product labels, „Danger“ indicates death, severe personal injury and/or substantial property damage will result if proper precautions are not taken.
*
WARNING
For the purpose of this User Manual and product labels, „Warning“ indicates death, severe personal injury or property damage can result if proper precautions are not taken.
*
CAUTION
For the purpose of this User Manual and product labels, „Caution“ indicates that minor personal injury or material damage can result if proper precautions are not taken.
*
NOTE
For the purpose of this User Manual, „Note“ indicates information about the product or the respective part of the
User Manual which is essential to highlight.
C A U T I O N !
This board contains components which can be destroyed by electrostatic discharge. Prior to touching any electronics board, your body must be electrically discharged. This can be simply done by touching a conductive, grounded object immediately beforehand (e.g. bare metal cabinet components, socket protective conductor contact).
W A R N I N G !
Hazardous voltages are present in this electrical equipment during operation.
Non-observance of the safety instructions can result in severe personal injury or property damage.
It is especially important that the warning information in all of the relevant
Operating Instructions are strictly observed.
2 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Description
1. Description
The EM11 I/O board is used for digitizing (analog inputs with A/D or V/F/D converters) and for the output of analog voltage signals, for the input of binary signals (speed), for input/output (binary I/O) and display (LED) of binary information.
The programmable address decoder calculates the board address, related to the board location.
The board features the following:
a) X6: For digitizing analog voltage signals:
* Four channels with A/D conversion,
* Four channels with V/F and subsequent F/D conversion
(V/F/D conversion)
b) X6: For the output of analog voltage signals:
* Two channels with D/A conversion
c) X5: For incremental encoding:
* One channel for actual speed value and position encoding with
inputs for two tracks plus the zero marking pulse;
* Subsequent digital filter and quadrupling the track frequency of
the incremental shaft angle encoder
* One input for function monitoring
d) X7: For the input and output of binary information:
* 16 binary inputs and 8 binary outputs.
* 4 binary outputs for signal states of connector X5
e) H10/H20: For display:
* 16 LED's on the front panel, logical order in two bytes:
* one byte (H10) with red LED's (H11-H18, H11 is the least sign. bit)
* one byte (H20) with yellow LED's (H21-H28, H21 is the least sign. bit)
* independent from binary signals in d)
The 40 pin BERG connector X7 at the front panel is arranged in three rows of ten and one row of six pins, whereas
* 10 pins are designed for 8-bit values,
external supply with P 24 external and M 24 external, and
* 6 pins are assigned to the zero marking pulse, track A signal,
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
3
Description
track B signal, monitor signal for connector X5, P 24 external and
M 24 external (the other 4 pins are not connected).
The connector is thus sub-divided into the following sections:
* 2 sections (bytes) for input,
* 1 section (byte) for output and
* 4 single bit output (1 bit information, wired and not configurable)
for the zero marking pulse, track A, track B and X5 monitor signal.
1.1. New functions
The board offers some additional features starting from version 3.0. It is compatible with former versions, as long as the following is adhered to:
- The nominal levels of the speed value input (connector X5) are 15 V.
- The 5 V (supply for a shaft angle encoder) are no longer available at
pins 9 and 10 of the connector X5.
1.1.1. RIC: *RDY-INTERNAL-CONTROL
The new connector RIC in the board screen is designed to suppress the board reset signal *BGRES when the *RDYIN signal occurs. An active signal *RDYIN usually generates a board reset *BGRES, which causes the outputs (analog and binary: output of zero volts) to be disabled. The board requires a renewed initialization. The RIC enables the board to continue running w i t h o u t *BGRES when a processor fails in the sub-rack (*RDYIN active).
Filtering out this signal is only effective until the next *RESAD (reset signal from the power supply, always generates a *BGRES).
If the *RDYIN is to be ineffective on the board, then a "Y" must be configured at the RIC connector
(i.e. the outputs remain active). The board does then not run a reset and the outputs remain enabled.
The default value of "N" in the STRUC-L screen corresponds to the functionality of the previous board version.
1.1.2. Speed Value Inputs
The three tracks A, B and zero are detected via differential inputs with a rated voltage level of 15V.
The threshold lies by approximately half the rated level with a hysteresis of 5 to 15% of the rated level
(see technical specifications). The corresponding minus terminal of each track may be grounded
(ground supply terminal of the digital encoder from X5:M').
4 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Description
1.1.3. Monitor Input of the Speed Value Connector
The supply of the speed plug connector with P5 is dispensed with because of the definition of the speed signal level (5V - level deleted). The pins 9 and 10 have therefore become available for a monitoring signal with a level of 15V. The threshold lies by approximately half the rated level with a hysteresis of 5 to 15% of the rated level (see technical specifications).
The corresponding minus terminal of each track may be grounded (ground supply terminal of the digital encoder from X5:M').
The speed input can be monitored with this monitoring input. Connection of a monitoring signal from the digital speed encoder or checking whether the encoders plug is connected by jumpering P15' with the positive input pin 9 and jumpering M' (ground) with the negative input pin 10.
1.1.4. Monitor Register for the Speed Value Input
The EM11 board has an additional monitor register starting from version3.0, which is accessed via the ZPC connector.
Currently only bit 7 (X5_OK, status of monitoring input of X5) is utilized.
+---+---+---+---+---+---+---+---+
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+---+---+---+---+---+---+---+---+
| | | | | | | |
| | | | | | | +--- irrelevant
| | | | | | |
| | | | | | +------- irrelevant
| | | | | |
| | | | | +----------- irrelevant
| | | | |
| | | | +--------------- irrelevant
| | | |
| | | +------------------- irrelevant
| | |
| | +----------------------- irrelevant
| |
| +--------------------------- irrelevant
|
+------------------------------- X5_OK, state of monitoring input of X5
This bit has the state HIGH, if the switching threshold of the monitor input on speed value connector X5 is exceeded (see technical specification).
Otherwise it is LOW.
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
5
Description
1.1.5. Binary outputs
Three new binary outputs have been installed on previously unconnected pins of the sub-connector
X7B (pins 12, 13, 14, see also connector allocation).
These outputs permanently take the state of internal 5V signals. These are set via output drivers to a
24V level (usual binary output SIMADYN D, no reaction on the original signal). The signals are the following:
X7, pin 11: zero marking pulse (as previous versions)
X7, pin 12: track A
X7, pin 13: track B
X7, pin 14: X5 monitor signal
1.1.6. Analog outputs
The two analog outputs of the board generate 0 V when disabled (in previous versions: -10V).
6 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
2. Board Design
* One slot (1 1/3 SPS)
* SIMADYN D local bus interface
* Programmable address decoder with board identification
* Three system timing controllers AM 9513
* One analog/digital converter AD 574, 12 bits
* One digital/analog converter AD 7549, 12 bits
* Four analog input channels with multiplexer and A/D converter
* Four analog input channels with V/F/D conversion
* Two analog output channels with D/A converters.
* One channel for the incremental shaft angle encoder consisting of
the following:
* Three pulse inputs (2 tracks, 1 zero marking pulse), one monitor input
(differential amplifier inputs, non-floating)
* 16 binary inputs
(non-floating)
* 8 binary outputs
(non-floating, 30 V/ 50 mA max.)
* 1 binary output for zero marking pulse
(non-floating, 30 V/ 50 mA max.),
* 1 binary output for track A
(non-floating, 30 V/ 50 mA max.),
* 1 binary output for track B
(non-floating, 30 V/ 50 mA max.),
* 1 binary output for X5 monitor signal
(non-floating, 30 V/ 50 mA max.),
* 16 LED's on the front panel.
Board Design
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
7
8
Application Notes
3. Application Notes
The EM 11 board can be used in all SIMADYN D sub-racks connected to the local bus. It requires one slot in the sub-rack.
The board must be fixed to the sub-rack with screws (even during commissioning) to ensure perfect operation.
If the board is plugged onto an adapter, the front panel (or better still one of the two metallized front panel handles) must be electrically connected to chassis via a short lead.
The pulse inputs at connector X5 are linked with the incremental shaft angle encoder of the drive via a multi-core screened cable.
The appropriate block diagram is shown in the appendix, diagram 1.
Supplementary Components at the Speed Input:
Component set
* SM1.1 6 DD 1680 - 0AB1
15 pin male connector, with casing
The analog input and output signal lines are connected via the SE7.1 interface module, which snaps onto the mounting rail. The 20 pin ribbon cable SC12 is used to inter-connect boards from connector
X6 to the interface module connector X1. The cable type SC12 (twisted pair) guarantees higher transmission security.
The SE7.1 interface module provides one screw-type terminal each for signal inputs
±
,signal outputs/ground and screen for each channel.
The SE40 interface modules enable additional boards to be connected (1-to-1 connection between faston connectors and screw-type terminals).
The configuration for analog signals is shown in the appendix in diagram 2.
Supplementary components used for analog signals:
Ribbon cable
* 20 pole, twisted pair, 1.5 m SC12 6 DD 1684 - 0BC0,
* 20 pole 2.0 m SC11 6 DD 1684 - 0BB0.
Interface modules
* SE7.1 6 DD 1681 - 0AH1
I/O block, analog, 8/10 channels
* SE40 6 DD 1681 - 0EA0
terminal block, 20 pole, one to one
Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Application Notes
The binary signal lines are connected as follows:
Ribbon cables are used to link connector X7 of the EM11 board with the interface modules (both ends are provided with ribbon cable socket connectors).
The corresponding block diagram is located in the appendix, as diagram 3.
The binary outputs are supplied with power (24V) via the interface modules.
The M24 ground is simultaneously reference potential for the binary inputs and is connected to the
SIMADYN D ground on the board.
Comments to diagram 3: to a) The 16 binary inputs and outputs at connector X7 of the EM11
are connected to the SE3.1 or SE23 interface module via a 40 pin
ribbon cable. The interface modules incorporate the external
connections for the plant (screw-type terminals).
to b) The binary inputs and outputs of the connector are split up and
allocated to four different SE4.1 interface modules. The 40 pin
connector is divided up into four separate cables by splitting
up the attached ribbon cable (4 x 10 pin, with sub-connector
identification, see diagram 3) at the ends and connecting
the four cable sections to the individual interface modules.
Thus it is possible e.g. to connect input or output signal lines
with or without galvanic isolation.
Supplementary binary input and output components
Ribbon cable
* 40 pin 2.0 m SC18 6DD 1684-0BJ0
* 40 pin --> 4+10 pin 2.0 m SC13 6DD 1684-0BD0
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
9
Technical Specification
Interface modules
* SE3.1 6DD 1681-0AD0
16 binary inputs and 16 binary outputs, non-floating
* SE4.1 6DD 1681-0AE1
8 binary inputs or outputs, non-floating
* SE5.3 6DD 1681-0AF3
8 binary inputs, 220 V, floating
* SE6.1 6DD 1681-0AG1
8 binary outputs, 220 V max., floating
* SE8 6DD 1681-0AJ0
8 binary inputs or outputs
(10 pin, one-to-one connection)
* SE23 6DD 1681-0CD0
16 binary inputs and 16 binary outputs
(40 pin, one-to-one connection)
* SE37 6DD 1681-0DH0
8 binary outputs, 24 V, floating
* SE41.1 6DD 1681-0EB1
8 binary inputs, 48 V, floating
* SE41.2 6DD 1681-0EB2
8 binary inputs, 24 V, floating
4. Technical Specification
GENERAL
INSULATION COORDINATION
AMBIENT TEMPERATURE
STORAGE TEMPERATURE
PROTECTION TYPE
HUMIDITY CLASS
ALTITUDE RATING
MECHANICAL STRESS
PACKAGING SYSTEM
DIMENSIONS
BOARD WIDTH
WEIGHT
CURRENT CONSUMPTION acc. to VDE 0110/1.89;contamination grade 2
0 to 55 deg. C, with unforced ventilation
-40 to +70 deg. C
IP00 acc. to DIN 40050
F to DIN 40040
S to DIN 40040
Installation in stationary, equipment, sensitive to vibrations
ES 902 C
233.4 x 220 mm
1 1/3 SPS = 1 slot = 20.14 mm
0.6 kg
P5 1.20 A
P15 0.10 A + Consumption connector X5, P15'
N15 0.15 A + Consumption connector X5, N15'
P24 0.10 A + Consumption connector X7A, X7B
BINARY INPUTS
NUMBER
INPUT VOLTAGE
FOR 0 SIGNAL
FOR 1 SIGNAL
INPUT CURRENT
10
16, no galvanic isolation
+24 V rated value
-1V to +6V; or binary inputs open
+13 V to +33 V
Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Technical Specification
- AT 1 SIGNAL
DELAY
BINARY OUTPUTS
NUMBER
SUPPLY VOLTAGE
- RIPPLE
- PERM. RANGE
- TEMPORARY
OUTPUT CURRENT AT 1 SIGNAL
- PERM. RANGE
SHORT-CIRCUIT PROTECTION
TO GROUND
DELAY
INDUCTIVE CIRCUIT INTERRUPT.
TOTAL LOAD
RESIDUAL CURRENT
SIGNAL LEVEL
- AT 0 SIGNAL
- AT 1 SIGNAL
5 mA (typical)
200 us
12, no galvanic isolation
24 V - rated value
3.6 V DC
+20 to +30 V, including ripple
+35 V, t < 0,5 sec.
50 mA rated value
O.2 mA to 60 mA
Electronic, unlimited duration
15 us at full load
4 us at no load (measurement instrument)
Limited to -1V
80 % at 55 deg. C all outputs 50 mA
20 uA at 0 signal
24 VDC rated
3 V max.
-2.5 V min. supply voltage
ANALOG OUTPUTS D/A CONVERSION
NUMBER
OUTPUT VOLTAGE (MIN.)
OUTPUT VOLTAGE (MAX.)
OUTPUT CURRENT (MAX.)
RESOLUTION
ACCURACY (ABSOLUTE / TYPICAL)
SHORT-CIRCUIT PROTECTION
TO GROUND
SHORT-CIRCUIT DURATION (MAX.)
TOTAL LOAD
2
- 10 V
+ 10 V
10 mA
11 bits + sign (corresponding to 5 mV)
±
0.25 % ( =
±
25 mV)
Ohmic resistance 56 Ohm
120 sec
All outputs simultaneously at 10 mA each
MEASURING SYSTEMS
ANALOG INPUTS WITH A/D CONVERSION
NUMBER
RATED INPUT VOLTAGE (MIN.)
RATED INPUT VOLTAGE (MAX.)
4
- 10V
+ 10V
OVERLOAD INPUT VOLTAGE (MIN.) - 14 V (absolute value)
OVERLOAD INPUT VOLTAGE (MAX.) + 14 V (absolute value)
INPUT RESISTANCE 20 kohms (differential amplifier input)
RESOLUTION 11 bits + sign (corresponding to 5 mV)
ACCURACY (ABSOLUTE / TYPICAL)
±
0.25 % ( =
±
25 mV)
ANALOG WITH V/F/D CONVERSION
NUMBER
RATED INPUT VOLTAGE (MIN.)
RATED INPUT VOLTAGE (MAX.)
OVERLOAD INPUT VOLTAGE (MIN.)
4
- 10V
+ 10V
- 14 V (absolute value)
OVERLOAD INPUT VOLTAGE (MAX.) + 14 V (absolute value)
INPUT RESISTANCE 20 kohms (differential amplifier input)
RESOLUTION 14 bits + sign (corresponding to 0.6 mV)
ACCURACY (ABSOLUTE / TYPICAL)
±
0.25 % ( =
±
25 mV)
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
11
Technical Specification
ACTUAL SPEED VALUE ACQUISITION
PULSE INPUTS TRACKS ZERO, A, B,
AND MONITOR INPUT
PULSE AMPLITUDE
PULSE FREQUENCY (MAX.)
SIGNAL LEVEL
1-SIGNAL
0-SIGNAL
15 V, 1 mA rated value
8-30 V, I maximum = 3 mA
100 KHz sin or squarewave sampling 1:1
7,5 V rated value for threshold
> 8 V
< 5 V, minimum: -30V
SWITCHING HYSTERESIS
SMOOTHING TRACKS ZERO, A, B
> 1 V
1 usec
SMOOTHING MONITOR INPUT 200 usec
POWER SUPPLY
P15'
M'
N15'
P15', M', N15', each via resistance
+15 V
±
10%, Imax = 250mA, Ri = 3,6Ohm
0 V
±
0,2V, Imax = 250mA, Ri = 0,9Ohm
-15 V
±
10%, Imax = 250mA, Ri = 3,6Ohm
SHORT CIRCUIT PROTECTION (GRD) Resistance (Ri)
SHORT CIRCUIT DURATION (MAX.) 1 sec., longer: Ri becomes infinite
NOTE : SPECIAL ATTENTION MUST BE PAID TO THE TOTAL LOADING OF THE
SUB-RACK POWER SUPPLY WHEN THE SUPPLY OUTPUTS AT PLUG
CONNECTOR X5 IS LOADED (CONCERNS P15', N15'). THIS IS
ESPECIALLY IMPORTANT WHEN SEVERAL EM11 BOARDS ARE SUPPLIED
FROM ONE SUB-RACK POWER SUPPLY. THE SIMADYN-D POWER SUPPLY
CUTS OUT WHEN OVERLOADS OCCUR (I.E. ALSO FOR SHORT CIRCUITS).
The practical resolution of the measuring systems depends on the function blocks used.
Measuring system Function block
---------------------------------------------------------------------------
A/D conversion
V/F/D conversion
ADC001 : analog input
AFC001 : analog frequency/digital conversion
D/A conversion
Actual speed value acquisition
DAM : analog output EM 11
NAV : digital actual speed value acquisition
12 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Connector Pin Assignments of the EM 11
5. Connector Pin Assignments of the EM 11
5.1. Pin Assignments for Actual Speed Value, Connector X5
Connector Function
7
8
9
10
11
5
6
3
4
1
2
Socket no.
12
13
14
15
Designation
Screen
Digital ground
NC
Zero marking pulse Z+
Track A+
Track A-
P15'
Digital ground
Monitor +
Monitor -
Zero marking pulse Z-
Track B+
Track B-
N15'
Screen
X5A, B
X5A, B
X5A, B
X5A,B
X5A,B
X5A,B
Voltage reference for
P15' or P5'
Not connected
Connection for zero marking pulse
Connection for track A
Inverse signal or zero voltage reference for track A
Supply voltage for encoder +15 V
Zero voltage reference for P15' or P5'
Monitor signal
Monitor signal, reference
Inverse signal or zero voltage reference point for zero marking pulse
Connection for track B
Inverse signal or zero voltage reference point for track B
Supply voltage for encoder -15V
5.2. Pin Assignments of the Analog Inputs and Outputs, Connector X6
Designation Connector Function
17
18
19
20
5
6
3
4
1
2
7
8
9
Pin no.
10
11
12
13
14
15
16
Analog input 1+
Analog input 1-
Analog input 2+
Analog input 2-
Analog input 3+
Analog input 3-
Analog input 4+
Analog input 4-
Input (V/F) 1+
Input (V/F) 1-
Input (V/F) 2+
Input (V/F) 2-
Input (V/F) 3+
Input (V/F) 3-
Input (V/F) 4+
Input (V/F) 4-
Analog output 1
Analog ground
Analog output 2
Analog ground
X6A
X6B
X6C
X6D
X6E
X6F
X6G
X6H
X6J
X6K
4 analog inputs with differential amplifiers and one A/D converter
(multiplexed)
4 analog inputs with differential amplifiers
V/F converters and F/D conversion
D/A conv., analog signal reference for output 1
D/A conv., analog signal reference for output 2
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
13
Connector Pin Assignments of the EM 11
The two analog outputs can only be addressed via function block DAM.
5.3. Pin Assignments for the Binary Inputs/Outputs, Connector X7
(40 pin faston connector)
26
27
28
29
30
21
22
23
24
25
13
14
15
16
17
18
9
10
11
12
19
20
31
32
33
34
35
36
37
38
39
40
6
7
8
3
4
5
1
2
Pin no.
Designation
Output 1
Output 2
Output 3
Output 4
Output 5
Output 6
Output 7
Output 8
P external
M external
Output 9
Output 10
Output 11
Output 12
N.C.
N.C.
N.C.
N.C.
P external
M external
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
Input 8
P external
M external
Input 9
Input 10
Input 11
Input 12
Input 13
Input 14
Input 15
Input 16
P external
M external
X7 C
X7 C
X7 C
X7 C
X7 C
X7 C
X7 C
X7 C
X7 D
X7 D
X7 D
X7 D
X7 D
X7 D
X7 D
X7 D
Connector
X7 A
X7 A
X7 A
X7 A
X7 A
X7 A
X7 A
X7 A
X7 B
X7 B
X7 B
X7 B
Function
Binary outputs
External power supply for binary inputs and outputs
Output for zero marking pulse
Not connected
External power supply for binary inputs and outputs
Binary inputs
External power supply for binary inputs and outputs
Binary inputs
External power supply for binary inputs and outputs
14 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
6. STRUC-L menu
: EM11 "I/O board mixed, L-bus"
ISE 1C = N "Ignore failed message (RDYINT) (Y/N) ?"
ZPC 8K < "Zero impulse monitor register"
X5A 4K < "actual position"
X5B 4K < "digital speed"
X6A 1K < "A/D converter 1"
X6B 1K < "A/D converter 2"
X6C 1K < "A/D converter 3"
X6D 1K < "A/D converter 4"
X6E 1K < "V/F/D converter 1"
X6F 1K < "V/F/D converter 2"
X6G 1K < "V/F/D converter 3"
X6H 1K < "V/F/D converter 4"
X7C 8K < "binary inputs 1"
X7D 8K < "binary inputs 2"
X6J 1K > "D/A converter 1"
X6K 1K > "D/A converter 2"
X7A 8K > "binary outputs 1"
H10 8K > "LED block 1: H11-H18"
H20 8K > "LED block 2: H21-H28"
STRUC-L menu
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
15
Miscellaneous
7. Miscellaneous
7.1. Appendices
7.1.1. Diagrams
a)
EM11
- X 5
- X 6
- X 7
Kabeltyp: SC18 type of cable: SC18
40
- X 1
Diagram 1
Externe Anschlüsse external connections b)
EM11
- X 5
- X 6
Kabeltyp: SC13 type of cable: SC13
40
- X 7
1
1 A
10
- X 1
11 B
- X 1
10
21 C
10
- X 1
31 D
10
- X 1
Externe Anschlüsse
16 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Miscellaneous
EM11
- X 5
- X 6
- X 7 type of cable: SC12 (twisted pair)
20
- X 1 external connections
Diagram 2
EM11
- X 5
- X 6
- X 7
Teilesatz SM1.1
set SM1.1
n
Kabeltyp: geschirmt, mehradrig nach Bedarf type of cable: shielded, n-way as needed
Anschluss Impulsgeber connection incremental encoder
Diagram 3
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
17
Miscellaneous
7.1.2. Drawings
Block diagram
Block diagram page 1 and 2
3GE.465 640.9002.01 SU
Dimension drawing and table of connectors
Dimension drawing showing front panel and table of connectors used: 3GE.465.640.9002.01 MB
Location diagram
Location diagram 3GE.465.640.9002.01 AO
18 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
ECB instructions
8. ECB instructions
Components which can be destroyed by electrostatic discharge (ECB)
Generally, electronic boards should only be touched when absolutely necessary.
The human body must be electrically discharged before touching an electronic board. This can be simply done by touching a conductive, grounded object directly beforehand (e.g. bare metal cubicle components, socket outlet protective conductor contact.
Boards must not come into contact with highly-insulating materials - e.g. plastic foils, insulated desktops, articles of clothing manufactured from man-made fibers.
Boards must only be placed on conductive surfaces.
When soldering, the soldering iron tip must be grounded.
Boards and components should only be stored and transported in conductive packaging (e.g.
metalized plastic boxes, metal containers).
If the packing material is not conductive, the boards must be wrapped with a conductive packing material, e.g. conductive foam rubber or household aluminum foil.
The necessary ECB protective measures are clearly shown in the following diagram.
a = Conductive floor surface b = ECB table c = ECB shoes d = ECB overall e = ECB chain f = Cubicle ground connection
Seated Standing Standing/sitting
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
19
ECB instructions
20 Edition 05.95
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Drives and Standard Products
Motors and Drives Systems Group
Postfach 3269, D-91050 Erlangen
ECB instructions
System-Based
Technology
Siemens AG Dk-Nr. 233141
SIMADYN D Hardware User Manual
Edition 05.95
21

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Digitizes analog inputs with A/D or V/F/D converters
- Outputs analog voltage signals
- Inputs binary signals (speed)
- 16 binary inputs and 8 binary outputs
- 16 LED's on the front panel