DL105 PLC Special Relays

DL105 PLC Special Relays
Special Relays
In This Appendix. . . .
— DL105 PLC Special Relays
1D
D--2
Special Relays
Appendix A
DL105 PLC Special Relays
“Special Relays” are just contacts that are set by the CPU operating system to
indicate a particular system event has occurred. These contacts are available for
use in your ladder program. Knowing just the right special relay contact to use for a
particular situation can save lot of programming time. Since the CPU operating
system sets and clears special relay contacts, the ladder program only has to use
them as inputs in ladder logic.
Startup and
Real-Time Relays
Appendix D
Special Relays
CPU Status Relays
System Monitoring
SP0
First scan
on for the first scan after a power cycle or program to run transition
only. The relay is reset to off on the second scan. It is useful where a
function needs to be performed only on program startup.
SP1
Always ON
provides a contact to insure an instruction is executed every scan.
SP3
1 minute clock
on for 30 seconds and off for 30 seconds.
SP4
1 second clock
on for 0.5 second and off for 0.5 second.
SP5
100 ms clock
on for 50 ms. and off for 50 ms.
SP6
50 ms clock
on for 25 ms. and off for 25 ms.
SP7
Alternate scan
on every other scan.
SP12
Terminal
run mode
on when the CPU is in the run mode.
SP16
Terminal
program mode
on when the CPU is in the program mode.
SP20
Forced
stop mode
on when the STOP instruction is executed.
SP22
Interrupt enabled on when interrupts have been enabled using the ENI instruction.
SP40
Critical error
on when a critical error such as I/O communication loss has
occurred.
SP41
Warning
on when a non critical error such as a low battery has occurred.
SP44
Program
memory error
on when a memory error such as a memory parity error has
occurred.
SP50
Fault instruction
on when a Fault Instruction is executed.
SP51
Watch Dog
timeout
on if the CPU Watch Dog timer times out.
SP52
Grammatical
error
on if a grammatical error has occurred either while the CPU is
running or if the syntax check is run. V7755 will hold the exact error
code.
SP53
Solve logic error
on if CPU cannot solve the logic.
DL105 PLC User Manual, 3rd Edition
Special Relays
Accumulator
Status
D--3
SP60
Value less than
on when the accumulator value is less than the instruction value.
SP61
Value equal to
on when the accumulator value is equal to the instruction value.
SP62
Greater than
on when the accumulator value is greater than the instruction value.
SP63
Zero
on when the result of the instruction is zero (in the accumulator.)
SP64
Half borrow
on when the 16 bit subtraction instruction results in a borrow.
SP65
Borrow
on when the 32 bit subtraction instruction results in a borrow.
SP66
Half carry
on when the 16 bit addition instruction results in a carry.
SP67
Carry
when the 32 bit addition instruction results in a carry.
SP70
Sign
on anytime the value in the accumulator is negative.
SP71
Invalid octal
number
on when an Invalid octal number was entered. This also occurs when
the V-memory specified by a pointer (P) is not valid.
SP73
Overflow
on if overflow occurs in the accumulator when a signed addition or
subtraction results in an incorrect sign bit.
SP75
Data error
on if a BCD number is expected and a non--BCD number is
encountered.
SP76
Load zero
on when any instruction loads a value of zero into the accumulator.
HSIO Pulse
Catch Relay
SP100 X0 is on
Equal Relays for
HSIO Mode 10
Counter Presets
SP540
Current = target value
on when the counter current value equals the value in V2320.
SP541
Current = target value
on when the counter current value equals the value in V2322.
SP542
Current = target value
on when the counter current value equals the value in V2324.
SP543
Current = target value
on when the counter current value equals the value in V2326.
SP544
Current = target value
on when the counter current value equals the value in V2330.
SP545
Current = target value
on when the counter current value equals the value in V2332.
SP546
Current = target value
on when the counter current value equals the value in V2334.
SP547
Current = target value
on when the counter current value equals the value in V2336.
SP550
Current = target value
on when the counter current value equals the value in V2340.
SP551
Current = target value
on when the counter current value equals the value in V2342.
SP552
Current = target value
on when the counter current value equals the value in V2344.
SP553
Current = target value
on when the counter current value equals the value in V2346
SP554
Current = target value
on when the counter current value equals the value in V2350.
SP555
Current = target value
on when the counter current value equals the value in V2352.
SP556
Current = target value
on when the counter current value equals the value in V2354.
SP557
Current = target value
on when the counter current value equals the value in V2356.
SP560
Current = target value
on when the counter current value equals the value in V2360.
SP561
Current = target value
on when the counter current value equals the value in V2362.
SP562
Current = target value
on when the counter current value equals the value in V2364.
SP563
Current = target value
on when the counter current value equals the value in V2366.
SP564
Current = target value
on when the counter current value equals the value in V2370.
SP565
Current = target value
on when the counter current value equals the value in V2372.
SP566
Current = target value
on when the counter current value equals the value in V2374.
SP567
Current = target value
on when the counter current value equals the value in V2376.
X0 — on for 1 scan after a pulse on X0 occurs.
Appendix D
Special Relays
DL105 PLC User Manual, 3rd Edition
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement