Macrom M-AN.DAB User Manual

Add to My manuals
1 Pages

advertisement

Macrom M-AN.DAB User Manual | Manualzz

DAB/DAB+

USER MANUAL

M-AN.DAB

Product overview

Front view

Film antenna

Amplifier

Foil for ground connection

Antenna connector

Product installation

Film protection adhesive

1

2

-4-

Film protection adhesive

1. Remove the protective film from the foil for mass connection and apply pressure on it to evenly apply the surface to the upright.

2. Gently remove the protective film during application and apply pressure on it to evenly apply the antenna to the glass.

Table of contents

Warranty

.............................................................................

3

Safety information

..................................................................

3

Specifications

.......................................................................

3

Product overview

Front view

.........................................................................

Connector available

4

4

Product location

....................................................................

5

Product installation

...............................................................

6-7

Declaration of Conformity

........................................................

8

Warranty

Thank you for purchasing this Macrom product. Should your product need warranty service, please return it to the shop where you buy it or to the

Macrom distributor in your country. The warranty does not cover damage due to improper use and or installation, incorrect connections to power supply, exposure to excessive humidity, unauthorized repair attempts or modifications.

Warning

Before starting installation, disconnect the cable from the negative battery terminal to avoid short circuits during installation.

This product must be installed properly by an authorized Macrom installer. Improper installation can damage the unit and / or the vehicle.

This product can only be used inside the vehicle.

Check electrical connections and driveability before installing.

The power of the received signal may vary depending on the following causes:

- Recommended dimensions for installation do not comply.

- Shielded, reflective or darkened windows with film.

- Antenna cable overlap with other electrical wiring of the vehicle.

- Noise produced by the windscreen wiper.

- Direction of the transmission station with respect to the position of the antenna.

Do not install the product on movable parts such as windor or door deflector.

Installation of this product may not be suitable for certain types of vehicles.

Specifications

Frequency 174-237MHz Band III, 1452-1492MHz Band-L

Impedance 50 Ohms

Gain 16-20dB (input power -30dBm)

Operation Voltage 5 Volts

30mA operation current

-2-

Product location

For safety reasons, the antenna must be installed on the passenger side.

To ensure optimum reception, spacing the film antenna from the top of the glass by 150mm and position it in more than 70mm from the side end of the glass.

Spin any other aerial of at least 100mm.

NOTE:

Be sure to check the installation location of the film antenna.

The antenna can not be re-glued.

Left-hand drive installation

Front anchor

Film antenn

150m

70mm

-3-

Product installation

Before gluing the parts, advise you to clean surfaces with detergent

(eg alcohol).

Heat the surfaces to allow good adhesion of the components. Position the antenna respecting the recommended distance. Paste the foil for the ground connection to the front upright. Paste the amplifier and then the antenna film

Make sure the antenna cable does not interfere with the airbag.

Left-hand drive installation

150mm

70mm

Fron t anchor

Film antenna

Airbag

Right-hand installation

150mm

Rear anchor

Film antenn

70mm

Right-hand installation

Front an chor

Film antenna

Airbag

150mm

70mm

-5-

DAB application

The DAB application is preloaded on the device.

Touch the DAB icon on the main interface to enter DAB mode.

You can also touch the DAB icon on the application page.

Declaration of conformity

-6-

If you want to use another application related to the DAB function, make sure that it is compatible with the Android system and that the functions are supported correctly.

Installation

Connect the DAB module to the DAB antenna supplied in the package.

Connect the micro USB to the DAB device and the USB to one of the

USB sockets of the central unit.

DAB antenna

To the USB main unit.

The manufacturer Aldinet S.p.A declares that the type of radio equipment - DAB+ receiver, model M-AN.DAB, brand Macrom - complies with the 2014/53 / EU Directive.

The full text of the EU Declaration of conformity is available at the following internet address: www.macrom.it, or at

Aldinet S.p.A. Viale Colombo, 8 - 20090 Trezzano S/N (MI) Italy

Made in China by Aldinet S.p.A.

Viale Colombo, 8 - 20090 Trezzano S/N (MI) Italy

-7-

DAB module

-8-

USB micro USB extension

The MACROM brand is a registered trade mark of ALDINET S.p.A.

ALDINET S.p.A

Viale C. Colombo, 8 - 20090 Trezzano s/N (MI) - Italy

Tel. +39 02 484781 w w w .

m a c r o m .

i t

advertisement

Related manuals

advertisement