Do-more with I/O, Communications and Control

Do-more with I/O, Communications and Control
Do-more with Extra Communications Ports
Both Do-more CPUs have one serial port built in...
Need more serial ports?
Then check out the two SERIO modules. Previously only available for our
WinPLC product line, the serial port modules are a great addition to the
Do-more PLC line-up, and allow connection of a wide range of serial
devices, such as barcode scanners, scales, printers, modems, etc.
176
H2-SERIO-4 $
176
H2-SERIO $
Three RS-232 ports
Two RS-232 ports &
One RS-422/485
Add serial ports for less than
$60 per port*!
Name your devices!
The CTRIO and CTRIO2 modules are capable of a wide
variety of high-speed input and output operations. Many of
these operations take place on board the module, and are
independent of the scan time of your PLC. With flexible
4-channel input and separate output channel design, these
modules can satisfy high-speed counting, timing, and pulse
catch operations, along with high-speed discrete output or
several profile choices of pulse output operations. Not all
combinations of input functions and output functions are
possible within the resources of the module, but these
examples are typical of the applications for these modules.
$
NEW
299
...makes it possible to “talk” to almost any device
by letting you define any non-standard data
exchange (serial or Ethernet)!
$
* $176 for 3-port serial comm module
301
$
Improved to Do-more!
NEW
Now all your serial port setup is done through the
Do-More Designer Software, and if you should need to
replace a serial module, all of its parameters and setup
are stored in the CPU and are automatically loaded
and ready to go when the system powers up.
Need more Ethernet?
The first Ethernet port is a real bargain - it’s built into
the Do-more CPU (H2-DM1E) for just $100 more than
the non-Ethernet version (H2-DM1). But many applications require a second Ethernet port. Add an H2ECOM100 and connect your Do-more to segregated
networks for security or isolation.
•
•
•
•
•
High-speed timing
Systems
Overview
The CTRIO and CTRIO2 modules can be configured for timing
functions based on both count or rate. Using a common configuration of a proximity switch sensing the teeth on a gear, the
module is able to calculate the velocity of the gear based on the
rate at which it receives counts. This value can be scaled within
the module to the engineering units required for the application.
Counting & timing up to 250 kHz:
H2-CTRIO2 $299.00
Four 250 kHz inputs, and two
20-250 kHz pulse train outputs
Counter
Quad Counter
Pulse Catch
Edge Timer
Dual Edge Timer
Outputs Supported:
• Pulse train - used for servo/stepper motor control.
Configurable for CW/CCW or step and direction.
• Discrete outputs - assigned to Counter/Timer input
functions
• Raw output - outputs controlled directly from the CPU
interface program
• Programmable limit switch (H2-CTRIO2 only)
Improved to Do-more!
NEW
Now all your CTRIO and CTRIO2 configuration is done
through the Do-More Designer Software - no more separate
software “workbench”. And if you should need to replace a
high-speed module, all the setup parameters and profiles are
stored in the CPU and are automatically loaded and ready to
go when the system powers up.
1 - 80 0 - 633 - 0405
C-more &
other HMI
Steppers/
Servos
Motor
Controls
Proximity
Sensors
Photo
Sensors
High-speed
edge timing
Limit
Switches
High-speed counting
The CTRIO and CTRIO2 modules can be configured for
counting functions via the use of an encoder input. Up to two
quadrature encoders per CTRIO or CTRIO2 module are
available with connections for external reset, capture and inhibit
signals. In a simple cut-to-length application as shown below,
the encoder provides an input position reference for the material to the module. The module's high-speed outputs are wired
to the cutting device and to the clutch and/or braking device.
When the count from the encoder is equal to a pre-programmed
setpoint within the module, the high-speed outputs are activated
to stop and cut the material to a repeatable fixed length.
Additionally, the clutch/brake signal can be used as an inhibit
signal so counts are not accumulated while the material is being
cut.
High-speed cut-to-length application
PLC with CTRIO2 module
Motor
Interface
Gearbox, clutch and
brake interface
CTRIO2
high-speed
output
Current
Sensors
Pressure
Sensors
Temperature
Sensors
Pushbuttons/
Lights
Process
Relays/
Timers
Comm.
Terminal
Blocks &
Wiring
Power
Enclosures
Tools
Pneumatics
Encoder
Safety
Cutter assembly
Appendix
Material to be
cut to length
w w w. a u to m at i o n d i re c t . c o m / d o - m o re - p l c s
Encoders
Circuit
Protection
Motor
control
lines
Product
Index
Volume 14
Programmable Controllers
Software
Motors &
Gearbox
Volume 14
e38-6
Field I/O
Soft
Starters
Gear
H2-CTRIO $291.00
Faster
Programmable
Controllers
Drives
PLC with CTRIO2 module
Counting & timing up to 100 kHz:
Inputs Supported:
Download the free Do-more Designer Software today and
take a look at these great features and so much more
Company
Information
Fast
Four 100 kHz inputs, and two
20-25 kHz pulse train outputs
Custom protocol instruction...
H2-ECOM100
High-speed operations
291
“Device abstraction” makes it easy to connect
external devices - give then logical names and
then refer to those names throughout your
program code for ease and clarity.
Watch the Video
about this topic:
http://bit.ly/PMdOt3
Do-more with High-speed I/O
Programmable Controllers
e38-7
Part #
Index
Do-more with Precise Motion Control
Company
Information
Systems
Overview
Rotary indexing liquid fill application
Here’s why
There are many applications that require accurate
motion control, whether it’s precision position control or
tight speed regulation. The Do-more PLC, using the
high speed pulse output mode on the H2-CTRIO2
module, offers a superior control solution for closedloop motion control using SureServo servo systems, or
super-low-cost open-loop control with SureStep stepping
systems.
Programmable
Controllers
PLC with CTRIO2 module
Field I/O
Fill spout
CTRIO pulse output signals
Software
C-more &
other HMI
Stepper or
servo drive
C-more Touch panel
Drives
Here’s how
Soft
Starters
When coupled with our
SureServo or SureStep motion
products, the resulting system is
extremely cost-effective.
Stepper motor
inside housing
The SureServo family of brushless servo systems from
AUTOMATIONDIRECT is fully digital and offers a rich set of
features at dynamite prices. Choose from eight standard
servo motors that can be used in combination with one of
three standard servo drives.
A Do-more-based motion
control system is very wellsuited to applications such as:
• cut-to-length
• indexing tables or
conveyors
• and many more...
These servos are designed for flexibility and quick implementation. SureServo drives accept a wide range of
command sources:
• Built-in motion controller with preset
position, velocity or torque
• Select presets with switch inputs
and/or the multi-drop Modbus serial
®
interface
• Position commands with “pulse and
direction”or CW/CCW format
(see section 16 of catalog)
• Encoder follower
• Analog voltage Velocity or Torque
command
• Eight standard systems from 100W to
3kW
• Use with DirectLOGIC PLCs or any other
host control
• Drives feature on-board indexer and
adaptive tuning modes
• Free set-up software
• 2 year warranty
AutomationDirect Do-more PLC with H2-CTRIO2 modules ($299.00) using pulse output feature
Familiar with H2-CTRIO?
Pulse output from
H2-CTRIO or H2-CTRIO2 module
If you’ve used our H2-CTRIO module in
the past, take a look at the new
H2-CTRIO2.
When coupled with a
Do-more CPU, you get:
• Faster pulse output frequency
(20-250 kHz)
• All configuration and motion profiles are
created in the Do-more Designer Software
and are stored in the CPU.
• The new “Axis Mode” instructions make
the code for your motion application a
cinch
For configuration, tuning and diagnostics, use the drive’s integrated
keypad/display or take advantage of the free SureServo Pro™ PCbased software. Tune the system easily with adaptive auto-tuning
selections or manual mode. Adapt to diverse applications with
configurable I/O,including 8 digital inputs, 5 digital outputs, 2
analog monitors and a scalable encoder output.
®
Download the free software today and see
for yourself.
(see section 16 of catalog)
The SureStep stepping family has four standard motors to handle
a wide range of automation applications such as woodworking,
assembly, and test machines. Our square frame or high torque
style stepping motors are the latest technology, resulting in the best
torque to volume. We have NEMA 17, 23, and 34 mounting
* Note: The Do-more PLC is compatible with the legacy H2-CTRIO module and you will benefit from having
the configuration and profiles created in the Do-more
Designer Software and stored on the CPU. This alone
is a big improvement over the previous functionality.
Ease of use out
of the box!
flanges and holding torque ranges from 83 oz-in to 434 oz-in.
A 20-foot extension cable with locking connector is a standard
accessory to interface any of the four stepping motors to the
microstepping drive, and can be easily cut to length if desired.
Volume 14
Volume 14
e38-8
Circular turn table
Programmable Controllers
1 - 80 0 - 633 - 0405
w w w. a u to m a t i o n d i re c t . c o m / d o - m o re - p l c s
Programmable Controllers
e38-9
Motors &
Gearbox
Steppers/
Servos
Motor
Controls
Proximity
Sensors
Photo
Sensors
Limit
Switches
Encoders
Current
Sensors
Pressure
Sensors
Temperature
Sensors
Pushbuttons/
Lights
Process
Relays/
Timers
Comm.
Terminal
Blocks &
Wiring
Power
Circuit
Protection
Enclosures
Tools
Pneumatics
Safety
Appendix
Product
Index
Part #
Index
Do-more with Remote I/O
Expand your I/O
Your local Do-more base can support 8 slots with as many as
32 I/O points in each. If you need more, you can install an
H2-ERM Remote I/O Master module in your local rack and
connect up to 16 remote I/O drops to expand your system.
Each of those 16 drops can provide hundreds more I/O
points. Need more? Add another H2-ERM, and connect 16
more. The Do-more CPUs can easily support thousands of
I/O points in a single system.
Kickstart your experience with the
Do-More Starter Kit
Locate I/O anywhere
DL205 (and DL405) remote I/O bases can each be located up
to 100 meters from the local base (or between Ethernet
switches) using EBC100 slave modules in the CPU slot. And
you have the flexibility of using Terminator rackless field I/O
drops as well.
With USB and
Seial Port
Choose the Do-more starter kit to get going fast.
You get a prewired, 3-slot base with your choice
of Do-more CPU, an 8-point input simulator
module, and an 8-point relay output module.
Systems
Overview
536
$
Only
626
With On-board Only
$
Ethernet
included
Also included are a copy of the Do-more
Designer software on CD, a hard copy of the user
manual, a USB programming cable, and a
coupon for free online training.
To configure the ERM Master module and its slaves, use a PC running the ERM Workbench tool
(included with Do-more Designer software). The PC may be removed once the system is configured.
Do-more CPU
Get started fast!
Company
Information
Stride
Ethernet
Switch
Both kits include a coupon for a 30-day free trial
of online training from Interconnecting
Automation (the official training partner of
AutomationDirect). You’ll get full, unlimited access
to all the training videos free for 30 days.
Steppers/
Servos
Motor
Controls
Proximity
Sensors
Photo
Sensors
Limit
Switches
Watch the Video
about this topic:
http://bit.ly/PzALlp
GS3 AC drive
Current
Sensors
Temperature
Sensors
H2-DM1-START - $536.00
H2-DM1E-START - $626.00
This Do-more H2 series PLC starter kit includes:
This Do-more H2 series PLC starter kit includes:
D2-03B-1
D2-03B-1
H2-DM1
CPU with RS-232 and USB ports
F2-08SIM
Input simulator
D2-08TR
Three-slot base (pre wired)
Input simulator
USB-CBL-AB6
USB programming cable
H2-DM-M
Do-more Designer Software
CD-ROM
And the coupon for 30 days of FREE Training
Relays/
Timers
F2-08SIM
Do-more User Manual
DM-PGMSW
Process
CPU with RS-232, USB and Ethernet Port Built-in
D2-08TR
USB programming cable
Pushbuttons/
Lights
H2-DM1E
Output module
USB-CBL-AB6
H2-DM-M
T1H-EBC100 remote I/O
Encoders
Pressure
Sensors
H2-EBC100 remote I/O
H4-EBC remote I/O
C-more &
other HMI
Motors &
Gearbox
This is everything you need to evaluate the
product and see for yourself what a powerful and
easy-to-use controller Do-more can be!
GS-EDRV100
Software
Soft
Starters
Includes everything!
Up to 100m
segments
between
switches
Field I/O
Drives
Free online training!
H2-ERM
Programmable
Controllers
Three-slot base (pre wired)
DM-PGMSW
Output module
Comm.
Terminal
Blocks &
Wiring
Power
Circuit
Protection
Do-more User Manual
Do-more Designer Software
CD-ROM
Enclosures
Tools
And the coupon for 30 days of FREE Training
Pneumatics
Safety
Appendix
NOTE: No substitution of individual part numbers.
Continue Reading about the Do-more Designer Software...
Volume 14
e38-10
Volume 14
Programmable Controllers
1 - 80 0 - 633 - 0405
w w w. a u to m at i o n d i re c t . c o m / d o - m o re - p l c s
Programmable Controllers
e38-11
Product
Index
Part #
Index
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement