VZ-AM03
Display 40”~55”
1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
articulated arm assembly (x1)
A adapter bracket (x2)
B
Package M
M5x14 (x4)
M-A
M6x14 (x4)
M-B
M8x20 (x4)
M-C
M6x30 (x4)
M-D
M8x30 (x4)
M-E
Package W washer (x4)
M-F small spacer (x8)
M-G big spacer (x4)
M-H
ST6.3x55 (x6)
W-A concrete anchor (x6)
W-B
D6 washer (x6)
W-C
2
1a. For Wood Stud Wall Mounting
Fits for 406mm(16" ) stud
55mm
( ( 2.2" )
1
ø 4 .
5 m m
( ø 3/16" )
2
Find and mark the exact location of mounting holes
3
Drill pilot holes
√
X X
W-C
W-A
Screw the wall mount onto the wall
1b. For Solid Brick and Concrete Mounting
60mm
( ( 2.4" )
ø 10 m m
( ø 3/8" )
1
Mark the exact location of mounting holes
2
Drill pilot holes
√
X X
W-B
W-C
W-A
Screw the wall mount onto the wall
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
WARNING
Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
4
5
2. Installing the Adapter Brackets
2-1 For Flat Back Screens
TV
TV
TV
M-F
M-A
M-B
M-C
Top of the display
2-2 For Recessed Back Screens or to Access A/V Inputs
TV
TV
TV
M-C
M-F or
M-G
M-C
M-D
M-E
M-F or
M-G
M-G
M-D
M-E
M-F or
M-H
M-D
M-E
M-F
M-G
M-H
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
· Position the adapter brackets as close as possible to the center of the display.
·
Screw the adapter brackets onto the display.
Tighten all screws but do not over tighten.
3. Hooking the Display onto the Wall Mount
wall
6
