advertisement
FV8010 User Manual
User Manual
FV8010 Series
Gateway
Version2.0
1
FV8010 User Manual
CONTENT
1 WELCOME................................................................................................................................ 4
2 INSTALLATION........................................................................................................................ 4
2.1 Package List ....................................................................................................................4
2.2 Safety Compliances.............................................................................................................4
3 PRODUCT OVERVIEW ........................................................................................................... 5
4 WEB CONFIGURATION ........................................................................................................ 6
4.1Physical connection..............................................................................................................6
4.2 Preparation for web configuration.......................................................................................6
4.3 User verification..................................................................................................................8
4.4 Current state ........................................................................................................................9
4.5 Network configuration ........................................................................................................9
4.5.1 WAN .........................................................................................................................9
4.5.2 LAN.......................................................................................................................... 11
4.6 VoIP...................................................................................................................................12
4.6.1 Public SIP server configuration (SIP1) ....................................................................12
4.7 Advance.............................................................................................................................14
4.7.1 DHCP service ...........................................................................................................14
4.7.2 NAT..........................................................................................................................15
4.7.3 Net service................................................................................................................16
4.7.4 Firewall ....................................................................................................................17
4.7.5 QOS 802.1P..............................................................................................................18
4.7.6 Advance....................................................................................................................19
4.7.6.1 SIP stun .......................................................................................................20
4.7.6.2 Public SIP back up server (SIP1 backup) ....................................................20
4.7.6.3 Private server (SIP2) ...................................................................................21
4.7.7 Digital map...............................................................................................................21
4.7.7.1 Fixed digital map.........................................................................................21
4.7.7.2 User define flexible digital map ..................................................................22
4.7.8 Call service...............................................................................................................23
4.7.8.1 Hotline.........................................................................................................24
4.7.8.2 Call feature ..................................................................................................24
4.7.8.2.1 Call forwarding.............................................................................24
4.7.8.2.2 Call waiting ..................................................................................25
4.7.8.2.3 Call transfer ................................................................................25
2
FV8010 User Manual
4.7.8.2.4 Three way conference .................................................................25
4.7.8.2.5 Black list .....................................................................................26
4.7.8.2.5 Limit list .....................................................................................26
4.7.9 MMI filter.................................................................................................................26
4.7.10 DSP ........................................................................................................................27
4.8 Dial peer............................................................................................................................28
4.9 Config manage (save and clear ) .......................................................................................32
4.9.1 Save..........................................................................................................................32
4.9.2 Clear .........................................................................................................................32
4.10 Firmware update..............................................................................................................34
4.10.1 Web update .............................................................................................................34
4.10.2 FTP and TFTP update.............................................................................................34
4.11 System manage................................................................................................................37
4.11.1 Account manage .....................................................................................................37
4.11.2 System reboot .........................................................................................................38
5 DEFAULT FACORY SETTING ............................................................................................39
6 CONFIGURATION BY PHONE ............................................................................................39
7 TELNET CONFIGURATION ................................................................................................40
7.1 Config Procedure ..............................................................................................................40
7.2 Telnet basic Introduction / Basic structure /Basic command ............................................40
7.3 Global Command ..............................................................................................................41
7.4 Net configuration ..............................................................................................................42
7.4.1 LAN interface settings .............................................................................................42
7.4.2 WAN interface settings.............................................................................................42
7.5 Netservice..........................................................................................................................42
7.6 Port settings.......................................................................................................................43
7.7 SIP settings........................................................................................................................43
7.8 –7.9 User management /Debug (Level 0~7) .....................................................................44
7.10 Show system running info...............................................................................................44
7.11—7.13 Logout / tracert trace network path info / update .................................................45
7.14—7.19 Upload / download configure/password/reload /Network
Diagnosis/Restore to factory default ...............................................................46
7.20 S POST Mode(safe mode)...............................................................................................47
7.20.1 Access POST mode process ...................................................................................47
7.20.2 POST mode clear....................................................................................................47
7.20.3 POST mode TFTP update firmware .......................................................................48
3
FV8010 User Manual
1 Welcome
FV8010 series of gateways are innovative gateways that offer a rich set of functionality and superb sound quality. They are fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market.
2 Installation
2.1 Package List
The FV8010 gateway package contains:
1) One FV8010 gateway
2) One universal power adapter
3) One Straight Ethernet cable
2.2 Safety Compliances
The gateway should only be operated with the universal power adapter provided with the package. Damages to the gateway caused by using other unsupported power adapters would not be covered by the manufacturer ’s warranty.
4
FV8010 User Manual
3 Product Overview
FV8010 IP Gateway is a next generation IP network facility based on industry open standard SIP (Session Initiation Protocol) . Built on innovative technology, FV8010 IP Gateway features market leading superb sound quality and rich functionalities.
Power : Output Power:12VDC,500mA.
Line : RJ11 port. Lifeline . Connect to PSTN line
Phone : RJ11 port, FXS . Connect to normal phone or PABX
WAN : RJ45 port.for Internet
LAN : RJ45 port.for PC
Power : Power indicator.
REG : Server indicator. Registered: ON; Registering: Blinking; Do not
register: OFF.
Phone : Indicate the calling status.
Hook-on: OFF.
Hook-off and in VoIP state: ON.
Hook-off and in PSTN state: OFF.
5
FV8010 User Manual
4.0 Web configuration
4.1 Physical connection
4.2 Preparation for Web configuration
The IP Gateway Web Configuration Menu can be accessed by the following
URL: http://Gateway-IP-Address. The default LAN IP address is
“192.168.10.1” and WAN IP address is “192.168.1.179”. If the web login port of the gateway is configured as non-80 standard port, then user need to input http://xxx.xxx.xxx.xxx: xxxx/, otherwise the web will show that no server has been found.
If connect PC with FV8010 LAN port and config to obtain IP address automatically, you could check the default gateway IP which is LAN IP address. The procedure as below
6
FV8010 User Manual a) Access to “Property of local area connection” dialog box b) Select “Internet Protocol (TCP/IP)”,click “Property” button c) Setting refers to below dialog box, and then click “OK” button, PC will obtain IP address automatically.（or set your pc static ip 192.168.10.2）
Method 1 Method2
7
FV8010 User Manual d) Input “cmd” command on the RUN submenu under PC START, key in
“ipconfig/all on the command lines dialog box to find the default gateway
IP address, which is FV8010 LAN IP address
4.3 User verification
Users are requested to make verification when config or browse the IP phone thru web pages, users can direct login the config menu by inputting username and password as below ,
Default username and password is:
8
FV8010 User Manual
4.4 Current State
On this page user can gather information of each commonly-used parameter of the phone, it is shown as the following figure:
l
Network section: Display the current WAN, LAN configurations of the phone
l
VoIP section: Display the current default signaling protocol in use ，and
l
server parameter in use of each protocol
Phone Number section: Display the phone number against each protocol
l
The version number and date of issue have been shown at the end of this page
4.5 Network configuration
Network configuration includes WAN Config and LAN Config.
4.5.1 WAN Configuration
This web page displays the WAN parameter configuration.
User can view the current network IP linking mode of the system on this page.
User will be authorized to set the network IP, Gateway and DNS if the system adopts the static linking mode. If the system selects DHCP service in the network which is using DHCP service, IP address will be gained dynamically.
9
FV8010 User Manual
If the system selects PPPOE service in the network which is using the
PPPOE service, then the IP address will be gained by the set PPPOE ISP internet and password of the account.
Note: if IP address has been modified, the web page will no longer respond owing to the modification, so new IP address should be input in the address field now.
Display <valid MAC > , that means the FV8010 had been certificated.
Display <invalid MAC> , that means the phone need a MAC Authenticating
Code .(get it from Favil or your provider )
Display <invalid MAC >,that means the FV8010 can not work normally.
Three models (Static /DHCP/PPPoE) are paratactic. Users can set the right model base on actual requirements.
l WAN Port static mode configuration
Default network config is DHCP model; Users need to set below parameters
IP Address
Netmask
WAN IP address
Network mask
10
FV8010 User Manual
Gateway
DNS Domain
Primary DNS
Alter DNS
Default gateway IP address
Option configuration
IP address for primary Domain Name Server
Option configuration
Click “Apply” button after finished above setting, IP Phone will save the setting automatically with immediate effect.
If users visit FV8010 thru WAN, user need to know the FV8010 WAN port ip address . ( on normal phone operation : #*111# for hear FV8010 saying
IP)
l WAN port DHCP mode configuration
Select “DHCP” on below single option, IP Phone will auto-config the WAN parameter with immediate effect.
l WAN port PPPoE mode configuration
Select “PPPOE” on below single option,
Set below parameter of PPPOE mode
Server
User
Password
If ISP no special requirements, remains default setting
Provided by ADSL ISP
Provided by ADSL ISP
Click “Apply” button after finished above setting, IP Phone will auto-config the WAN parameter with immediate effect. The setting of WAN is still effective and enables IP Phone to connect to internet.
4.5.2 LAN Configuration
This web page displays the LAN parameter configuration. Please note once the bridging mode is selected, the LAN configuration will be no longer effective.
11
FV8010 User Manual
Configuration Example
l
Config LAN: generally config one private IP address
IP
Netmask
LAN IP address
Network Mask l Start LAN DHCP Service and NAT or not: default setting is start
Start Bridge Mode or not（transparent mode）: Once start Bridge Mode, some parts of LAN config will be disabled, and the phone will no longer set IP address for LAN physical port，LAN and WAN will join in the same network；
4.6 VOIP Configuration
This section is to config signaling protocol for the SIP Server and Client.
4.6.1 SIP 1 configuration
User can configure specific parameter of SIP1 on this page；
12
FV8010 User Manual
Definition of each parameter described as below
SIP[Unregistered]
SIP register state；if register successfully, show “Registered” in the
Configuration
Register Server address square bracket，otherwise show Unregistered
Set SIP register server IP address
Proxy Server addr Set proxy server IP address（usually SIP will provide the same
Register Server Port
Proxy Server Port
Register Username
Proxy Username
Register Password
Proxy Password
Domain Realm
Local SIP Port
Phone Number
Register Expire Time
Detect Interval Time
RFC Protocol Edition
DTMF Mode
User Agent configuration of proxy server and register server, if different(such as different IP addresses), then each server's configuration should be modified separately）
Set SIP register server signal port
Set SIP proxy server signal port
Set SIP register server account username（Usually it is the same with the config port number）
Set the SIP proxy server account username
Set password of SIP register server account
Set password of SIP register account
Enter the sip domain if any, otherwise FV8010 will use the proxy server address as sip domain. (Usually it is same with registered server and proxy server IP address).
Set local signal port，the default is 5060
Set assigned phone number
Set expire time of SIP server register, default is 120 seconds
Set detection interval time of server, default is 120 seconds
Enable the phone to use protocol edition. When the phone need to communicate with phones using SIP1.0 such as CISCO5300 and so on, need to modify into RFC2543. the default is to RFC3261；
Set DTMF sending mode, support RFC2833, DTMF_RELAY (inband audio) and SIP info
Set the user agent if have, default is common
13
FV8010 User Manual
Enable Register
Auto Detct Server
Enable Pub Outbound
Proxy
Server Auto Swap
Configure enable/disable register
Co-work with Server Auto Swap and Detect Interval Time. Enable this option, FV8010 will periodically detect whether the public SIP server is available, if the server is unavailable, the FV8010 will switch to the back-up SIP sever, and continue detecting the public sip server. FV8010 will switch back to the primary SIP server if the server is available again.
Configure to enable to use public outbound proxy，if you have no stun server , advise to enable the option
Configure main and backup auto-swap server；if the phone enables main and backup server function ， the automatic detection and auto-swap functions should both be chosen
After finished the aforesaid network and VoIP configurations on the phone and network communication has been implemented，the user can make VoIP calls by the calling register and proxy server.
Note:
Some ISP internet may inhibit the phone to register and cancel the register in process, so user had better cancel apply or register soon and then submit registration repeatedly. Server may stop response of dialogue machine, then the phone receives no register/cancel login request and registration state will show incorrectness!
Configuration Example
Firstly users should get the account info from VOIP Service Provider
(Including Server IP address, port, username, password etc.) and follow below procedure.
l
Config registered server and proxy server IP address and signaling port.
(Support DNS for registered server and proxy server)
l
Config the username and password for registered server and proxy server.
l
Config the phone number (Usually phone number is same with SIP account)
14
FV8010 User Manual
Remark: due to the above register username is “client”, so the phone number is different from SIP account)
l
Config the domain realm (Usually it is same with registered server and proxy server IP address, Let it be blank)
l
Select below two option and registered in local outbound public proxy
&
Usually these two option need to be selected, when you want to use SIP1.
4.7 Advance
4.7.1 DHCP server configuration
When FV8010 work as a router, This config is for network device which connect to FV8010 LAN port.
DNS Relay: DNS relay acts as a forwarder between the DNS Clients and the
DNS Servers, DNS relay is designed for home/office networks where the users might want to dial into more than one Internet Service Provide (ISP)
15
FV8010 User Manual
DHCP server manage page.
User may trace and modify DHCP server information in this page.
DNS Relay:
enable DNS relay function.
User may use below setting to add a new lease table.
Lease Table Name:
Lease table name.
Lease Time:
DHCP server lease time.
Start IP: Start IP of lease table.
End IP:
End IP of lease table. Network device connecting to the FV8010
LAN port can dynamic obtain the IP in the range between start IP and end IP.
Netmask:
Netmask of lease table.
Gateway:
Default gateway of lease table
DNS:
Default DNS server of lease table.
Notice: This setting won’t take effect unless you save the config and reboot the device
4.7.2 NAT Configuration
This page is for NAT configuration, such port forward, DMZ.
Network Address Translation (NAT) provides a mechanism for a privately addressed network to access registered networks, such as the Internet, without requiring a registered subnet address. This eliminates the need for host renumbering and allows the same IP address range to be used in multiple intranets. With NAT, the inside network continues to use its existing private or obsolete addresses. These addresses are converted into legal addresses before packets are forwarded onto the outside network.
16
FV8010 User Manual
Advance NAT setting. Maximum 10 items for TCP and UDP port mapping.
IPSec ALG:
Enable/Disable IPSec ALG;
FTP ALG:
Enable/Disable FTP ALG;
PPTP ALG:
Enable/Disable PPTP ALG;
Transfer Type:
Transfer type using port mapping.
Inside IP: LAN device IP for port mapping.
Inside Port:
LAN device port for port mapping.
Outside Port: WAN port for port mapping.
Click Add to add new port mapping item and Delete
to delete current port mapping item.
4.7.3 NAT service configuration
4.7.3.1
Configure web browse port，the default is 80 port，if you want to enhance system safety，you'd better change it into non-80 standard port；
Example: The ip address is 192.168.1.70 . you change the port value to
8090, the accessing address is http://192.168.1.70:8090
But if the value is 0, that imply it can’t be configured by web browser.
4.7.3.2
Configure telnet port，the default is 23 port. You can change the value to others .
Example: The ip address is 192.168.1.70 . you change the port value to
8023, the accessing address is telnet 192.168.1.70:8023
17
FV8010 User Manual
4.7.3.3
Enable RTP initial port configuration. It is dynamic allocation.
4.7.3.4
Configure the maximum quantity of RTP port. The default is 200；
Leased IPMAC correspondence table of DHCP.The table will display all device getting ip address from FV8010 LAN port by DHCP .
The configuration on this page needs to be saved after modified and will go into effect after restarting.If the Telnet, HTTP port will be modified, the port is better to be set as greater than 1024,because the 1024 port system will save ports.
※
Set the HTTP port as 0，then the http service will be disabled.
4.7.4 Firewall
Firewall setting page. User may set up firewall to prevent unauthorized
Internet users from accessing private networks connected to the Internet
(input rule), or prevent unauthorized private network devices to access the internet.
18
FV8010 User Manual
Access list support two type limits: input access limit or output access limit.
Each type supports 10 items maximum.
FV8010 firewall filter is base WAN port. So the source address or input destination address should be WAN port IP address.
Configuration:
in access enable Enable in access rule out access enable Enable out access rule
Input/Output: Specify current adding rule is input rule or output rule.
Deny/Permit: Specify current adding rule is deny rule or permit rule.
Protocol Type:
protocol using in this rule: TCP/IP/ICMP/UDP.
Port Range:
port range if this rule
Src Addr:
Source address. Can be single IP address or network address.
Dest Addr:
Destination address. can be IP address or network address.
Src Mask:
Source address mask. Indicate the source is dedicate IP if set to 255.255.255.255. Otherwise is network ID
Des Mask:
Destination address mask. Indicate the source is dedicate IP if set to 255.255.255.255. Otherwise is network ID
Example:
Intention: Computer A cannot ping computer B
Computer A connect with FV8010 LAN port
Computer A IP address is 192.168.10.2
FV8010 WAN port IP address is 192.168.0.187
FV8010 LAN port IP address is 192.168.10.1
Computer B IP address is 192.168.0.200
FV8010 firewall config
19
FV8010 User Manual
4.7.5 QOS 802.1p Configuration
QoS Control based on 802.1p for different IP users. The QoS is used to mark the network communication priority in the data link/MAC sub-layer. FV8010 will sorted the packets using the QoS and sends it to the destination. QoS provides service classes for accessing traffics in Internet.
QoS Enable:
Enable QoS service.
QoS Table:
Enable include QoS table, FV8010 will only provide QoS service to the network address included in the QoS table. Disable the option. FV8010 provides QoS service to the network address outside the QoS table.
Delete
Enter the IP/MASK configure and select delete-to-delete corresponding item
Add:
User can set the QoS Table using IP and Netmask. the IP can be network address (set netmask to 255.255.255.255)
4.7.6 Advance
20
FV8010 User Manual
To show the phone whether has been registered on public server or private server；
4.7.6.1 SIP STUN Configuration
STUN can support SIP terminal's penetration to NAT in the inner-net. In this way， as long as there is conventional SIP proxy and a STUN server placed in the public net, it will do; but STUN only supports three NAT modes：FULL
CONE, restricted, port restricted.
IF you have stun server .please input stun server address here.
The STUN server default port is 3478
The unit is minute. if you have STUN server .please input interval time for
STUN`S detection on NAT type.
Configure enable/disable SIP STUN；if you have stun server .please enabe the option.
4.7.6.2 Public backup server configuration the specific configuration parameter has the same meaning with public server. It should be noted that the username and password should be the same with the public main server.
21
FV8010 User Manual
4.7.6.3 Private server(SIP2) configuration.
Specific configuration parameter has the same meaning with public server.
Configure permit/deny private server register；
Configure enable/disable private outbound proxy； if you have no stun server .advise to enable the option.
Note: about how to use SIP ,Please refer to the Dial peer chapter.
4.7.7 Digital map configuration
4.7.7.1 Fixed digital map
End With “#”: Use # as the end of dialing.
Fixed Length: When the length of the dialing match, the call will be sent.
Timeout:
Specify the timeout of the last dial digit. The call will be sent after timeout
22
FV8010 User Manual
4.7.7.2 User define flexible Digital map table
Digit map is a set of rules to determine when the user has finished dialing.
Digital Map is based on some rules to judge when user end their dialing and send the number to the server. With digital map, users don’t have to press
‘
#’ key or "call” key after dialing. If the number dialed matches some item in the digital map table, or it doesn’t match with any item, this number will be sent out immediately. It is not like using dial peer . Using digital map won’t change the number dialed, the number sent is the same as the number dialed.
X
Represents any one number between 0 and 9.
Tn
Represents the last digit timeout. here [ n ] represents the time from 0~9 second, it is necessary. Tn must be the last two digits in the entry. If Tn is not included in the entry, we use T0 as default, it means system will sent the number immediately if the number matches the entry.
.
(Dot) represents any number and no length limit.
[ ]
Number location value range . It can be a number range(such as [1-4]), or number is separated by comma such as [1,3,5],, or use a list such as
[234]
Example:
[1-8]xxx
Any 4 digits number between 1000 and 8999 sending out immediately
9xxxxxxx
any 8 digits number starting with 9 sending out immediately
911
after finishing dialing 911 ,it will send out immediately
99T4
after finishing dial 911, it will send out in 4 second
9911x.T4
any more than 5 digits length starting with 9911, sending out in 4 second .
Using digital map can be combined with dial peer . First digital map will determine when the user finished dialing, then convert this number to the number actually sent according to "dial peer table ".
23
FV8010 User Manual
When user dial 2887 or 98765432、 911 、99 、9911234，they will send out immediately. (digital map with dial peer)
4.7.8 Call Service Configuration
Value added service configuration
On this page, user can set value added services such as hot-line ，call forwarding，call transfer (CT)，call-waiting service，three way call，blacklist， out-limit list and so on.
24
FV8010 User Manual
4.7.8.1 Hotline
Configure hot-line number of the port. With this number of the port，this hot-line number will be dialed automatically as soon as off-hook and user can's dial any other number. If you do not use hotline , please let it be blank.
Configuration example:
4.7.8.2 Call feature
4.7.8.2.1 Call forwarding.
Call forward default is Disabling. when is selected，if the number dialed is engaged after the phone has received a call, then it will automatically transfer to the configured number according to the following picture (CF001 ) configuration. when is selected，if the phone do not receive the incoming call .it will automatically in forward to the configured number according to the following picture (CF001 forward ) configuration. when is selected， then the phone will directly transfer all incoming call to the number that had configured in advance like the picture showing.
Note:
1 Number can be sip server extension number or DID number (any PSTN number)
2 the function has no relationship with the option enable or disable that
If it is enabled . the phone will not ring when there is a incoming call . DND, do not disturb, enable this option to refuse any calls.
25
FV8010 User Manual
Enable this to forbid outgoing calls.
The unit is second. no answer call forward time setting.
4.7.8.2.2 Call Waiting configuration
Configure enable/disable call waiting service；After it is enabled, user hold calls of the other party by <FLASH >button, by pressing <FLASH >button again, the call can go back to the previous call. If you want to use three way conference , this option must be enabled.
4.7.8.2.3 Call transfer configuration
It is for enabling or disabling If it is enabled, when user A are talking with user B , A press <FLASH> button on the normal phone ,After dialing dial * then dial the third party number (C user) directly. the phone will transfer the calls to C. The result is C phone will ring (A will hang up) . User
C pick up phone then user B will talk with C .
Operating process ：
<FLASH> button
+* +
third party number
Example:
A are talking with B .
A click FLASH button (holding B line). then dial
* user C number
.
4.7.8.2.4 Three-way conference call
Configure enable/disable three way call；When user A are talking with user
B as the call origination，user A click <FLASH> button on the normal phone to hold user B line and then dial the third party user C.
after A talk with C ,
User A click<FLASH> button again to recover the talk with user B. At this
26
FV8010 User Manual time user A press * key to make C into the three way conference .
Operating process ：
<FLASH> button
+ third party number
+
<FLASH> button
+ *
Example:
A are talking with B .
A click FLASH button (holding B line ) .then dial C number .
A will talk with C .
A click FLASH button again (holding C line ), and A dial
*
A 、B、 C make the three party conference sucessfully now
4.7.8.2.5 Black List
Incoming call in these phone numbers will be refused. It is for precluding incoming communication like Call ID. If user don't want to answer a certain phone number, please add this phone number to the list, and then this number will be unable to get through the phone.
4.7.8.2.6 Limit list
Outgoing calls with these phone numbers will be refused for example, if user don't want the phone to dial a certain number, please add the number to this table, and the user will be unable to get through this number.
4.7.9 MMI Filter
27
FV8010 User Manual
MMI filter is used to make access limit toFV8010.
When MMI filter is enable. Only IP address within the start IP and end IP can access FV8010.
4.7.10 DSP configuration
On this page, user can set speech coding，IO volume control, cue tone standard, caller ID standard and so on.
Configuration Explanation：
Configure Coding Rule according to network bandwidth; support G.711a/u
G.729
Congfigure Signal Standard according to country’s phone voice;
Normally, G729 Payload Length don’t need be changed into 10 ms;
Handset out volume.
28
FV8010 User Manual
4.8 Dial peer
Number IP table configuration
Function of number IP table is one way to implement the phone's calling online, and the calling of the phone will be more flexible by configurating the number IP table. For example, user know the other party's number and IP and want to make direct call to the party by point-to-point mode： the other party's number is 1234，make a configuration of 1234 directly ,then the phone will send the called number1234 to the corresponding IP address； Or set numbers with prefix matching pattern，for example, user want to make a call to a number in a certain region （ 010 ）， user can configure the corresponding number IP as 010T― protocol― IP，after that, whenever user dial numbers with 010 prefix( such as 010－62201234),the call will be made by this rule.
Bases on this configuration，we can also make the phone use different accounts and run speed calling without manual swap. When making deletion or modification, select the number first and click load, then click
Modify and complete the operation.
Display of calling number IP image list.
Click Add，the following figure will be shown at the lower part of the page.
It is to add outgoing call number, there are two kinds of outgoing call number setup： One is exactitude matching，after this configuration has been done, when the number is totally the same with the user's calling
29
FV8010 User Manual number, the phone will make the call with this number's IP address image or configuration; Another is prefix matching（ be equivalent to PSTN's district number prefix function），if the previous N bits of this number are the same with that of the user's calling number(the prefix number length) ，then the phone will use this number's IP address image or configuration to make the call. When configurating the prefix matching, letter "T" should be added behind the prefix number to be distinguished from the exactitude matching.
Configure the calling line route： SIP and lifeline
Configure destination address，if it is point-to-point call，then input the opposite terminal's IP address, it can also be set as domain name and resolved the specific IP address by DNS server of the phone. If no configuration has been made, then the IP will be considered as 0.0.0.0. This is an optional configuration item.
Configure the other party's protocol signal port, this is optional configuration item：when nothing is input, then the default of h323 protocol is 1720，the default of sip protocol is 5060；lifeline required no configuration of this item, shown as 0.
Configure alias，this is optional configuration item：it is the number to be used when the other party's number has prefix；when no configuration has been made, shown as no alias.
Configure suffix，this is optional configuration item：it is the additive dial-out number behind the number; when no configuration has been made, shown as no suffix；
30
FV8010 User Manual
Example 1
T mean any length digit number.
Destination is 255.255.255.255 that mean calling out through SIP2 server.
Destination is 0.0.0.0 that mean calling out through SIP1server
Config page Explaination Example
That means Any digits number starting with
9 pass throught SIP2 server.
Here alais is del
Delete Length is 1 that means the phone will delete the first number before send number to server
It can be used for speed calling
The number user dialed will be replaced fully by the number that is behind all: )
Here alias is all: (not all)
User dial 93333
SIP2 server receive 3333
User dial 2
Sip1 server receive 33334444
It can be used to add local area or prefix.before sending out.
It saves user dialing number .
Here alias is add: (not add)
User dial 8309
SIP1 server receive07558309 user want to dial PSTN（010 6228）by SIP1， while actually the called number should be
86106228 ， then we can configure called number as 010T, then rep：8610，and then set the replacing length as 3. So that when user make a call with 010 prefix, the number will be replaced as 8610 plus the number and then sent out.
Relace the number that user dialed before sending to SIP1 server.
Here alias is rep:(not rep) this is optional configuration item.it is to add number behind the number user had dialed. when no configuration has been made, shown as no suffix
User dial 010 6228
SIP1 server receive8610 6228
User dial 147
Sip1 server receive 147 0011
31
FV8010 User Manual
Example 2
When user dial 200 , It will pass through SIP2
When user dial 2009 , It will pass through SIP2
When user dial 20096, It will pass through SIP2
When user dial 201, It will pass through SIP1
When user dial 20, It will pass through SIP1
Example 3 (about lifeline )
Image of *T means when user connect PSTN line to the lifeline port, user could make PSTN call by add a “*” before the calling number.
32
FV8010 User Manual
Phone number = *T
Call mode =lifeline
When user dial * ,there is a second dial tone from the pstn line . then dial as directly using PSTN line.
Phone number = 1
Call mode =lifeline
When user dial 1 ,there is a second dial tone from the pstn line . then dial as directly using PSTN line.
Phone number = 22
Call mode =lifeline
When user dial 22,there is a second dial tone from the pstn line . then dial as directly using PSTN line.
Example 4
IP to IP calling
“Peer to Peer” calling mode: direct make calls and no need to set phone number thru proxy server (user could refer to Dial peer setting on web configuration charter).The phone should be operated under following condition (satisfy one option)
l Requirement 1 both two FV8010 are assigned the public IP
address individually
l Requirement 2 both two FV8010 using private IP address should
be on the same LAN.
If A dial number 187 , A can talk with B . If B dial number 155 , B can talk with A
33
FV8010 User Manual
4.9 Config Manage (Save and Clear configuration)
Notice: clear config in admin mode, all settings restores to factory default; clear config in guest modem, all settings except sip, advance sip restore to factory default.
4.9.1 Save Config
Once change is made, Users should save the modified configuration to take effect, otherwise the IP Phone will go back to the last saved setting after phone reboot.
The interface of “Save Config” as below, please follow the four steps below to config.
Enter “Config Manage” Menu →“Save Config” Submenu→ Click “Save”
Button→ Return to “Current State” Web page
4.9.2 Clear Config
There are four method to clear config(set factory default), web 、telnet 、post mode、keypad.If the IP Phone doesn’t work properly after modifying config, users can clear all modified config on “Clear Config” web page. The phone will clear all modified config and restore the default factory configuration.
(Default network type for WAN is DHCP mode; default LAN IP address is
192.168.10.1)
Process Please follow the below steps to clear config:
Enter “Config Manage” Menu →“Clear Config” →Click “Clear” Button
→show “Submit Success” info on screen →Click “Return” button
34
FV8010 User Manual
4.10 Firmware Upgrade
4.10.1 Web Update
On this page, user can select the upgrade document
(firmware or config file) from hard disk of the computer directly to run the system upgrade. After upgrade completed ， reset the phone and it will be usable immediately.
Firmware format is *.dlf as suffix
STEP:
Enter Update menu →WEB Update submenu→ click “browse” button→ download upgrade document from hard disk (firmware or config file provided by manufacturer) → click “Update” button →reboot IP phone to go into effect
Note:
Under system upgrade progress, FV8010 may not be restarted normally due to some system reason (e.g. electricity shut off), users can re-download under post mode.
4.10.2 FTP and TFTP Update
Users can download upgrade documents or lead in configuration files thru
FTP or TFTP mode.
Please make sure export and import rights are authorized by FTP or TFTP server before using FTP update way.
35
FV8010 User Manual
Definition of each parameter described as below
Server Set IP address for upload or download FTP/ TFTP server
Username
Password
File name
Type
Set username of the upload or download FTP server. If user select
TFTP mode, no need to input username and password
Set upload or download of FTP server password
Set file name for system upgrade documents or system configuration files. system file take .Z as suffix，configuration files take .cfg as suffix；
Config export/import/upgrade file type [three options]: “Application update” is system documents upgrade
“Config file export” is export configuration files to server
“Config file import” is import configuration files to gateway
Protocol
STEP:
Set transport protocol type [two options]:FTP and TFTP
Enter Update menu →FTP Update submenu→ Config FTP/TFTP server →
Config username and password of FTP server (if select TFTP mode, please skip this step) →key in file name → choosing file type from the dropdown menu→ choosing protocol type
Example: (export config file)
1 FTP
<1> Copy Wftpd32 software and FV8010 Firmware into a new Folder
( example c:/tmp)
<2> Run wftd32.exe. Set a user name and password for FV8010 ftp
36
FV8010 User Manual updating
The process is like the below picture showing from step 1 to step 13.
Update the firmware Download config file to you PC
After it update successfully. You will find the new version in Current State
After you click apply , you can find the file that it had download to your pc <c:\temp>
37
FV8010 User Manual
4.11 System Manage
4.11.1 Account Manage (maximum 5 account )
Users can edit users (add or delete) account and modify existing users’ authority on this web page.
Definition of each parameter described as below
User Name
User Level
List existing phone user account name
Show existing user account level [two option]:Root and
General: Root level users have the right to modify config;
Add
Delete
Modify
General level users have the right to read-only
Add user account to IP phone
Delete increased user account
Modify increased user level and password
Operation Example
l
Add one new account
Click “Add” button →input User name (No-Modify) →Choosing User level from dropdown menu →set new user password →confirm password
→submit the new account info by clicking “submit” button →show “submit success” on screen →return to account configuration interface by clicking
“Return” button
l
Delete increased account
Choosing the account need to del from dropdown menu→ Delete account by pressing
“Delete button” →show “Submit Success” on screen
38
FV8010 User Manual
l
Modify increased account (For Root-level user account only)
Choosing the modified account →enter below interface →modify user level or password →click “Submit” button to submit the modification
Owing to the phone's default account ： accounts of the administrator level-admin account and the ordinary level－guest account are all weak account and weak password, the username and password will be easily to guess on public network, so the user had better modify the administrator and ordinary user.
Enter with manager level when making modification，create a administrator account and a browse account (you'd better not set the name as admin, administrator, guest, etc.)，set password and then save configuration， entering with new manager account, delete default manager and browse account and save configuration，security will be enhanced!
4.11.2.System Reboot
Once any change of phone configuration is made, users need to reset IP phone to go into effect. Users should save the modified configuration before system reboot, otherwise the phone system configuration will go back to last saved setting. The system reboot interface as below
39
FV8010 User Manual
5 Default Factory Setting
l Gain IP address thru DHCP mode, WAN Port static IP is 192.168.1.179,
LAN port IP is 192.168.10.1.Default is to start the DHCP service and NAT function.
l Default communication protocol is to use SIP, SIP port is 5060 l Default HTTP port is 80, Telnet port is 23 l Default number end is “#” button l Default user account is admin and guest
6 Configuration by phone
We have provided some command to config FV8010 by phone. We can connect one analog phone to “Phone” interface. We can input following command by Hand free or Handset.
Input #**** Reboot Device;
Input #*000 Clear configuration;
Input #*100 Gateway work at Static mode
Input #*101 Gateway work at DHCP mode
Input #*102 Gateway work at PPPoE mode
Input #*103 Gateway work at Bridge mode
Input #*104 Gateway work at Router mode
Input #*111 Get the IP address of Gateway by voice message
Input #*222 Get the Number of Gateway by voice message
40
FV8010 User Manual
7 Telnet configuration
7.1 Config Procedure
l Input command “cmd” on Run submenu under
PC START menu, and then key in “telnet phone-IP-address
enables users to config IP phone thru telnet.
l Input username and password, both default
Username and password of Administrator account are “admin”
l Config IP Phone through command lines
Note:
1. We suggest users to config IP Phone thru web browser instead of keypad or telnet.
2. After any change of configuration, please remember to make “write” command to save changes and then input “reload” command to reboot IP phone to take effect.
7.2 Telnet basic Introduction
7.2.1 Basic structure
User may use telnet command to access and manage gateway.
FV8010 adopts tree structure for telnet. Every node contains its sub-nodes or local command. User can type “help” or “?” whenever to see sub-nodes and all local command under current node.
Besides local command, there are some global commands can be used in each node.
7.2.2 Basic command
Logout: exit telnet mode.
Write: save current settings.
Type sub-nodes name in current node to switch to sub-node.
Type “!” or “exit” in current node to return to parent-node.
Type “help” or “?” can see all sub-nodes and all local command under current node, every help item has comments such as <command> or <node> to distinguish sub-nodes and local command. Type “help” or “?” in command can see all parameters using in this command.
When typing node name or command, user no need to key the full name, use
TAB button will make it more efficient.
There are two types in command parameters: optional and required.
“required” parameter use “-” as prefix and “optional” use “_” as prefix. User may type “-” or “_” then press TAB button for complementarily.
41
FV8010 User Manual
7.3 Global Command
Global command is available under all nodes, FV8010 support following commands.
Command Name Command function chinese Set the language of help prompt info to
Chinese clear english exit help history logout ping tree who
Write
Reload
Clear screen
Set the language of help prompt info to
English
Go back to upper level of node
Example
#chinese
#clear
#english
#exit
1.Display help prompt info
2.Display all subnode under current node and local command
Display the history info for inputting command
Exit telnet config interface
One test program using to check network or program availability
1．#help ping
2．#help
#history
#logout
#ping www.google.com.
Print out the tree structure of current node #tree
Display current users login to PC #who
Save configuration to flash #write
Reboot IP phone #reload
Common Network command
Command
Name ping tracert show basic show ip route show ip arp
Command function
The same with above stated
Print out the network path
Print current configuration status table
Print phone Router table
Print phone arp table show ip netstat Run Netstat program telnet telnet another user host
Set default Clean phone configuration modification and restore default except network configuration
Set all default Clean all configuration and restore default manufacturing setting
Example
#ping www.google.com
#tracert www.google.com
#show basic
#show ip route
#show ip arp
#show ip netstat
#telnet 192.168.1.2
#setdefault
#setdefault all
42
FV8010 User Manual
7.4 Net configuration
7.4.1 LAN interface settings
Path: <config-interface-fastethernet-lan>#
Function Command
[disable]enable bridge mode
[disable]enable DHCP service
[disable]enable NAT
[no]bridgemode
[no]dhcp-server
[no]nat
Show current DHCP rules
Show LAN port IP address
Show NAT info
Change LAN port IP address dhcpshow ipshow natshow ip –addr x.x.x.x –mask x.x.x.x
Example:
# config interfact fastethernet lan
<config-interface-fastethernet-lan># ip –addr 192.168.1.10 –mask 255.255.255.0
7.4.2 WAN interface settings
path: <config-interface-fastethernet-wan>#
Function Command
[disable]enable dhcp client
[disable]enable pppoe
[disable]enable QOS
Set default gateway IP
Clear default gateway IP
Set WAN port IP address
Show WAN port settings
[no]dhcp
[no]pppoe
[no]qos gateway x.x.x.x no gateway ip –addr x.x.x.x -mask x.x.x.x show
Example:
# config interface fastethernet wan
<config-interface-fastethernet-wan># ip –addr 202.112.241.100 –mask 255.255.255.0
You need to reconnect if the WAN port has been changed.
7.5 Netservice path: <config-netservice>#
Function Command
Set DNS address dns -ip x.x.x.x _domain xxx
Set alternate DNS address
Set hostname
Set http access port
Show http access setting
Set telnet access port
Show telnet access port
Set RTP initial port and quantity alterdns -ip x.x.x.x _domain xxx hostname xxx http-port xxx http-port telnet-port xxx telnet-port media-port –startport xxx –number xxxx
43
FV8010 User Manual
Add route rule
Delete route rule set callerid mode disable callerid
Disable call forward
[disable]enable call transfer
[disable]enable call waiting route –gateway x.x.x.x –addr x.x.x.x –mask x.x.x.x no route –gateway x.x.x.x –addr x.x.x.x –mask x.x.x.x
Show route info Route
Show netservice info show
Example:
# config netservice
<config-netservice># dns –ip 202.112.10.36 _domain voip.com
<config-netservice># media-port –startport 10000 –number 200
<config-netservice># route –gateway 202.112.10.1 –addr 202.112.210.1 –mask 255.255.255.0
7.6 Port settings path: <config-port>#
Function Command callerid xxx no callerid no callforward
[no]calltransfer
[no]callwaiting dtmfvolume xxx
[no]threetalk show
Set DTMF gain
[disable]enable3-way conference
Show port settings
7.7 SIP settings path: <config-sip>#
Function
[disable]enable registration
[disable]enable auto detect server
Set sip domain
Set DTMF mode
Set auto detect interval time
Command
[no] register
[no] detect-server default-domain xxx dtmf-mode xxx interval-time xxx
[no]swap-server [disable]enable auto swap server
Set local SIP signal port
Set proxy server
Set register server info
Set alter proxy info
Set alter server info signalport xxx server proxy -ip x.x.x.x _port xxx _user xxx _password xxx server register -ip x.x.x.x _port xxx –user xxx _password xxx alter-server proxy –ip x.x.x.x _port xxx _user xxx
_password xxx alter-server register –ip x.x.x.x _port xxx _user xxx
44
FV8010 User Manual
Show current sip info
_password xxx show
Example:
#
config sip server
<config-sip-server>#
server proxy ip 210.25.23.22 _port 5060 _user aaa _password 123456
7.8 User management path: <config-user>#
Function Command
Change user right.
Change user password
Add new user
Delete user entry access –user xxx –access xxx password –user xxx entry –user xxx –access 5 (or 12) no entry –user xxx
Show current sip info show
Example:
#
config user
<config-user>#
entry –user abc –access 7
Example:<config-user>#
access –user aaa –access 7
Note:
The command :
–user xxx –access digit
Here if the digit is less 10 , then the user level is guest
If the digit is more that 10 ,then the user level is administrator
7.9 Debug (Level 0~7) path: <debug>#
Function Command show debug setting show
[disable]enable debug all modules [no] all xxx
[disable]enable debug app module [no] app xxx
[disable]enable debug cdr module [no] cdr xxx
[disable]enable debug sip module [no] sip xxx
[disable]enable debug h323 module [no] h323 xxx
[disable]enable debug tel module [no] tel xxx
[disable]enable debug dsp module [no] dsp xxx
7.10 show system running info path: <show>#
Function show: accesslist (firewall) settings show network status show current call info
Command accesslist basic call active
45
FV8010 User Manual
show CODEC capability show debug info show LAN status and DHCP server info show digital-map info show LAN info show WAN info show arp table info
Show DNS gateway info
Show netstate info
Show route info
Show icmp packets Stat.
Show igmp packets Stat.
Show ip packets Stat
Show RTP packets Stat.
Show TCP packets Stat.
Show UDP packets Stat. show gateway memory show NAT information show caller-ID info show dsp info show hotline info show black list info show outgoing limit info show current phone number show current port status show PPPoE info show QoS table info show sip info show UDP tunnel info show running time show gateway version
7.11 Logout
Usage: #telnet –target -port
Login:xxx
Password:xxx #
#logout
7.12 tracert trace network path info usage: #tracert –host
Example:# tracert www.google.com
7.13 update usage:
capability debugging dhcp-server dial-rule interface fastethernet lan interface fastethernet wan ip arp ip dns ip netstat ip route ip icmp ip igmp ip ip ip rtp ip tcp ip udp memory nat port callerID port dsp port hotline port in-limit port out-limit port number port status pppoe qos sip udptunnel uptime version
46
FV8010 User Manual
# update ftp –user xxx –password xxx –ip x.x.x.x –file xxx
# update tftp –ip x.x.x.x –file xxx
Example:
# update ftp –user abc –password 123 –ip 202.112.20.15 –file FV8010.z
7.14 upload configure file usage:
# upload ftp –user xxx –password xxx –ip x.x.x.x –file xxx
# upload tftp –ip x.x.x.x –file xxx
7.15 download configure to flash usage: #download tftp –ip x.x.x.x –file xxx
#download ftp –user xxx –password xxx –ip x.x.x.x –file xxx
Example:
#
download ftp –user abc –password 123 –ip 202.112.20.15 –file FV8010.cfg
7.16 password usage:
#password
Enter new password:
xxx
Confirm new password:
xxx
7.17 reload usage: #reload
Reboot system
7.18 Network Diagnosis
There are some telnet commands for checking your network. Now Listing below for your information
Command Function Example ping tracert
Check if the destination is accessible
Show network path info show basic Show network settings show ip route Show route table
#ping www.google.com
#tracert www.google.com
#show basic
#show ip route show ip arp Show arp table show ip netstat Netstat programe
#show ip arp
#show ip netstat telnet Telnet to another device #telnet 192.168.1.2
7.19 Restore to factory default
#setdefault (clear gateway settings expect network part)
#setdefault all (clear all settings.)
47
FV8010 User Manual
7.20 POST Mode(safe mode)
7.20.1 Access Post mode process
1 PC connect to FV8010 LAN port
2 Set your PC IP to be 192.168.10.205
3 Power off .
4 after power on ,within 4 seconds , telnet 192.168.10.1
5 config page is like below (if no page like the below .do step 4 again.)
7.20.2 Post mode clear
Input 3 and enter for clear configuration
48
FV8010 User Manual
7.20.3 post mode TFTP update firmware
Input 1 for TFTP update firmware
Process:
1 Run TFTP server
2 Copy firmware into your TFTP server
3 After access post mode , input 1 for selecting TFTP updating.
4 Input TFTP server address
5 Input firmware name and then enter
6 Input d for starting download
7 If updating successfully ,It will display
8 Input x for logout TFTP client
9 Input 4 for logout POST mode
FV8010 provide safe mode. When there is booting problem because of setting problem or firmware problem. User can restore the factory setting or upgrade to a new firmware to solve this problem.
49
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
