LXC620
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
LXC620
Generator controller user manual
1.1
er1
Ver
Date: 2012/08
08//08
620 Series
LXC
LXC6
61
0 Series
LXC
LXC61
610
Software Version
Date
2010-10-20
2012-08-08
Version
1.0
1.1
Note
Start publishing
Increased DTU binding and remote monitoring function
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
1 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Sign
NOTE
CAUTION!
Instruction
Highlights an essential element of a procedure to ensure correctness.
Indicates a procedure or practice, which, if not strictly observed, could
result in damage or destruction of equipment.
Indicates error operation may cause death, serious injury and
significant property damage.
WARNING!
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
2 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Contents
1. Performance and characteristics.........................................................................................................................4
2. Technical parameters............................................................................................................................................6
3. Operation................................................................................................................................................................ 7
3.1. Key functions...............................................................................................................................................7
3.2. Automatic start/stop operation..................................................................................................................8
3.2.1. Starting sequence:.......................................................................................................................... 8
3.2.2. Stopping sequence:........................................................................................................................ 9
3.2.3. Manual start/stop operation:.......................................................................................................... 9
3.3. Switch control procedures.......................................................................................................................10
3.3.1. LXC620 ATS switch control procedures....................................................................................10
3.3.2. LXC610 Switch control procedures............................................................................................10
4. SMS remote control、wireless remote control................................................................................................11
5. Based on the GPRS DTU remote online monitoring......................................................................................12
5.1. DTU with the binding of the controller...................................................................................................13
5.2. Password generation and change the interface.................................................................................. 14
6. History query........................................................................................................................................................ 15
6.1. Event log....................................................................................................................................................15
6.2. History alarm............................................................................................................................................. 15
7. Protection..............................................................................................................................................................16
7.1. Warnings....................................................................................................................................................16
7.2. Shutdown alarm........................................................................................................................................17
7.3. Trip alarm...................................................................................................................................................19
7.4. SMS alarm.................................................................................................................................................19
8. Parameter setting................................................................................................................................................ 21
8.1. Parameter setting,content and scope of list......................................................................................... 22
8.2. Programmable output port can be defined content table1-4............................................................. 25
8.3. Programmable input port 1-6 definition content list.............................................................................27
8.4. Custom project name list.........................................................................................................................27
8.5. Sensor selection list................................................................................................................................. 28
8.6. Conditions of crank dinsconnect selection........................................................................................... 29
9. Wirings connection.............................................................................................................................................. 29
10. Typical applications...........................................................................................................................................31
11. Installation...........................................................................................................................................................34
11.1. Case dimension and fixing size........................................................................................................... 34
11.2. Battery voltage input.............................................................................................................................. 34
11.3. Speed sensor input................................................................................................................................ 34
11.4. Output and expand relays.....................................................................................................................34
11.5. Ac input....................................................................................................................................................34
11.6. Withstand voltage test........................................................................................................................... 35
12. Common faults and exclusion method...........................................................................................................35
13. Product packaging.............................................................................................................................................35
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
3 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
1. Performance and characteristics
LXC610:Auto Start Module. It controls gen-set to start or stop automatically by remote start signal.
LXC610
LXC620
LXC620:Auto Main Failure, updates based on LXC610, especially for automatic system composed by
gens and mains.
�
With ARM-based 32-bit MCU, highly integrated hardware, new reliability level;
�
132x64 LCD with backlight, multilingual interface (including English, Chinese or other
�
languages)which can be chosen at the site, making commissioning convenient for factory personnel;
�
Equipped with advanced networking capabilities,via GPRS mobile network and Internet
connectivity,in any place where the network can be remotely monitor;
�
Leasing industry applications: management provides the perfect solution: leased out via PC remote
Management of the unit, you can monitor all operating parameters (oil pressure, water temperature,
voltage, current, power, etc),you can always change the configuration to protect the unit is not proper
application, can record 200 detailed fault information, including: time to failure, because ,when the
voltage, current, power, oil pressure, water temperature and other key parameters, and ready to
upload to the monitoring machine. Another multi-level password management options to facilitate the
lease management;
�
RS485 communication port enabling remote control, remote measuring, remote communication via
ModBus protocol;
�
Protection, automatic Start & Stop gen-set, ATS(Auto Transfer Switch) control with perfect fault
indication and protection function;
�
Parameter setting: parameters can be modified and stored in internal FLASH memory and cannot be
lost even in case of power outage; most of them can be adjusted using front panel of the controller
and all of them can be modified using PC via USB;
�
Equipped with SMS (Short Message Service) function. When gen-set is alarming, controller can send
short messages via SMS automatic to max. 5 telephone numbers. User can control or check genset
by sending Short Message;
�
Adjust the controller `s configuration by the computer via USB, RS232, RS485 interface;
�
More kinds of curves of temperature, pressure, fuel level can be used directly and users can define
the sensor curves by themselves;
�
Multiple crank disconnect conditions (speed sensor, oil pressure, generator frequency) are optional;
�
Event log, real-time clock, scheduled start & stop generator (can be set as start gen-set once a
day/week/month with load or not);
�
All output ports are relay-out;
�
For Mains, controller has over and under voltage, over and under frequency, loss of phase and phase
sequence wrong functions; For generator, controller has over and under voltage, over and under
frequency, loss of phase, phase sequence wrong, over and reverse power, over current functions;
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
4 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
�
3 fixed analog sensors (temperature, oil pressure and liquid level);
�
2 configurable sensors can be set as sensor of temperature, pressure or fuel level;
�
Widely power supply range DC(8~35)V, suitable to different starting battery voltage environment;
�
Can be used for the pumping unit as an indicating instrument (indicate and alarm are enable only,
relay is inhibited );
�
Fully functional,and can detect almost all the generating units of electrical parameters and
non-electrical parameters.
DETECT PROJECT :
MAINS AND GENERATOR ABNORMAL
CONDITIONS
CONDITIONS:
Mains
Voltage is too high
Voltage is too low
Line voltage Uab,Ubc,Uca
Frequency is too high
Phase voltage Ua,Ub,Uc
Frequency is too low
Frequency Hz
Phase loss
Gens
Loss of power
Line voltage Uab,Ubc,Uca
Phase voltage Ua,Ub,Uc
THE FAULT DISPLAY AND PROTECTION
FUNCTION PROJECT
PROJECT:
Frequency Hz
High water temperature warn
Load current IA,IB,IC
High water temperature shutdown alarm
Each phase and total active power kW
Low oil pressure warning
Each phase and total reactive power kVar
Low oil pressure shutdown
Each phase and total apparent power kVA
Over speed shutdown alarm
Each phase and average power factor PF
Box high temperature warn
Accumulate total gens power kWh、kVarh、kVAh
Low fuel level warn
Battery voltage is too high warn
Sensor
Temperature WT
Oil pressure OP
Battery voltage is too low warn
°C、 °F Choose to display
kPa、Psi、Bar Choose to display
Load over current shutdown alarm
Failed to stop alarm
Fuel level FL %(unit)
Emergency stop alarm
Speed SPD RPM(unit)
Oil pressure sensor open circuit
Voltage of Battery VB V (unit)
Voltage of Charger VD V (unit)
Hour count HC can accumulate Max.65535 hours.
Start times can accumulate Max.65535 times
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
5 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
2. Technical parameters
Items
Contents
Operating Voltage
Power Consumption
DC 8.0V to DC 35.0V, Continuous Power Supply.
<3W(standby:≤2W)
Alternator Input Range
3-Phase 4-Wire
3-Phase 3-Wire
Single-Phase 2-Wire
2-Phase 3-Wire
12V AC - 360 V AC (ph-N) 3 Phase 4wire
23V AC - 620 V AC (ph-ph) 3 Phase 3wire
12V AC - 360 V AC (ph-N)
12V AC - 360 V AC (ph-N)
Alternator Frequency
50/60Hz
Speed sensor voltage Vpp
1.0 - 70Vpp(Peak to peak)
Speed sensor Frequency
10000Hz(max.)
Start Relay Output
10Amp
DC28V
Fuel Relay Output
10Amp
DC28V
Programmable Relay Output 1
10Amp
DC28V
Programmable Relay Output 2
10Amp
DC28V
Gens Closed Programmable Relay Output 3
10Amp
250VAC Free output
Mains Closed Programmable Relay Output 4
10Amp
250VAC Free output
Case Dimension
209mm x 146mm x 33mm
Panel Cutout
182mm x 137mm
C.T. Secondary
5A Rated
Working Conditions
Temperature:(-25~+70)℃ Humidity:(20~90)%
Storage Condition
Temperature:(-40~+70)℃
Protection Level
IP55: when waterproof rubber seal installed
between controller and panel fascia.
Insulating Intensity
Object: input/output/power
Quote standard: IEC688-1992
Test way: AC1.5kV/1min leakage current: 3mA
Net Weight
LXC620=0.448Kg
LXC620 User Manual
�: T:+86-769-23836636
LXC610=0.433Kg
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
6 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
3. Operation
3.1. Key functions
This button places the module into its Stop/reset mode.
When engine is running,pressing this key will stop the engine.
When a shutdown alarm occur,pressing this key will reset alarm.
his button is for testing the LEDs and screen.Press for a long time to
light them.
Stop/Reset key
Start key
Start genset in Manual mode or Test mode.
Manual mode key/
Config“-”key
Pressing this key will set the module into manual mode.
In setting parameter status,pressing this key will decease setting value.
Manual test mode/
Config“+”key
Pressing this key will set the module into manual test mode.
In setting parameter status,pressing this key will increase setting value.
Pressing this key will set the module into automatic mode.
In setting parameter status,pressing this key will shift cursor or confirm
Setting value.
In the parameter display and record query screen,press this key to
make a scroll operation.
Press this button more then three seconds, it show genset abnormal
shutdown record.If long press again, display back to main page.
Auto key/
Config“enter”key
View history record
key
In the parameter display and record query screen,press this key to
make a scroll operation.
Scroll key
Tips: Press
is correct.
and
simultaneously, enter into advanced parameters setting menu if password
Tips
Tips:: default password is 0000, user can change it in event of others change the senior parameters
setting.Please closely remember it after changing If you forget your password, please contact our
customer service, at the same time press the key all the information back to the service personnel.
Note: the lights indicate
Configurable indicating lamp: a total of 4, but the action needed by PC configuration, very flexible;
Gens normal indicator: it brights when gens is normal .it flickers when gens abnormal .it extinguished
when there is no gens.
Gens load indicator lamp: indicator when load is on gens.
Mains normal indicator: it brights when mains is normal .it flickers when mains abnormal .it extinguished
when there is no mains.
Mains load indicator lamp: indicator when load is on mains.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
7 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
3.2. Automatic start/stop operation
Press
,and the indicator besides the key illuminates, which indicates unit is in auto start mode.
3.2.1. Starting sequence:
Press
,then the button indicating lamp bright. The generator is in “automatic start mode”. In the
automatic mode, the generator will be auto to start and stop according requirement (no need any human
action). In this mode, three type starting request can trigger starting process.
The 1st one is mains failure (over voltage, under voltage, over frequency, under frequency , simulation of
mains failure enter valid).(This condition is valid only for LXC620)
The 2nd one is the remote start input or SMS remote start .
The last one is the schedule running.
Once the start request is triggered and no fault, began to perform automatic boot sequence:
�
Start Delay timer is shown on Status page of LCD;
�
When start delay is over, preheat relay outputs (if this be configured),“preheat start delay XX s”is
shown in LCD;
�
When preheat delay is over, fuel relay outputs 1s and then start relay output; if engine crank fails
during“cranking time”, the fuel relay and start relay deactivated and enter into“crank rest time”to wait
for next crank;
�
If engine crank fails within setting times, the controller sends Fail to Start signal and “Fail To Start”
message appears on LCD alarm page;
�
In case of successful crank attempt,“safety on timer”starts. During this period, low oil pressure, high
water temperature, under speed, charge failure alarms are disabled. As soon as this delay is
over,“start idle delay”is initiated (if configured);
�
During“start idle delay”, under speed, under frequency, under voltage alarms are inhibited. When this
delay is over,“warming up delay”starts (if configured);
�
When“warming up delay”is over, if generator state is normal, its indicator will be illuminated. If voltage
and frequency has reached on-load requirements, the closing relay will be energized, generator will
accept load, generator power indicator will turn on, and generator will enter Normal Running state; if
voltage and frequency are abnormal, the controller will initiate alarm (alarm type will be displayed on
LCD alarm page).
� NOTE: In case of “Remote Start (off Load)”, the procedure is the same, except for step NO. 7: the
closing relay will NOT be energized, generator will NOT accept load.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
8 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Stopping sequence:
3.2.2.
3.2.2.S
�
LXC620:when mains return normal during gen-set running, enters into mains voltage “Normal
delay”.When mains normal delay are over, enter into “stop delay” and mains indicator lights; also can
be into this mode when “remote start on load” is inactive.
�
LXC610:generator enters into“stop delay”as soon as“Remote Start” is inactive.
�
When stop delay is over, close generator relay is un-energized; generator enters into “cooling time
relay”. After “transfer rest time”, close mains relay is energized. Generator indicator extinguishes
while mains indicator lights.Then began "cooling delay", and during the period if mains failure or
remote start is active,generator return to the gens on load.
�
Idle relay is energized as soon as entering “stop idle delay”.
�
In the "stop idle delay" after the end,if enter“ETS hold delay”, ETS relay is energized. Fuel
deactivated and decides whether generator is stopped or not automatically.;
�
In the "ETS delay" after the end,then enter genset "Fail to stop timer",auto decides whether generator
is stopped or not.
�
When the generator stopped,enter the standby generator;If the generator does not stop the controller
alarm(LCD Screen Display Shutdown failure warning).
relay is
Manual start/stop operation:
3.2.3.
3.2.3.M
�
LXC620: Press
, controller enters into Manual mode and its indicator lights. Press
then
controller enters into "Manual Test Mode"and its indicator lights. In the both mode, press
to start
generator, can automatically detect crank disconnected, and generator accelerates to high-speed
running. With high temperature, low oil pressure and abnormal voltage during generator running,
controller can protect genset to stop quickly (please refer to No.4~9 of Auto start operation for
detail procedures). In“manual mode
”, the procedures of ATS please refer to ATS procedure of
generator in this manual.In“Manual Test Mode ”, generator runs well, whether mains normal or
not, loading switch must be transferred to generator side.
�
LXC610: Press
, controller enters into Manual starts mode and its indicator lights. Then
press
to start generator, can automatically detect crank disconnected, and generator accelerates
to high-speed running. With high temperature, low oil pressure and abnormal voltage during
generator running, controller can protect genset to stop quickly (please refer to No.4~9 of Auto start
operation for detail procedures). After generator runs well, if remote start signal is active, controller
will send closing gens signal; if the remote signal is inactive, controller won t send closing signal.
�
can shutdown the running generator(please refer to No.3~8 of stopping
Manual shop:press
sequence for detail procedures)
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
9 of
35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
3.3. Switch control procedures
LXC620 ATS switch control procedures
3.3.1.
3.3.1.LXC620
Auto transfer procedures:
When controller is in Manual Test, Auto or Stop mode, switch control procedures will start through
automatic transfer.
Note: When the input port has the following configuration of situations:
/Gens Auxiliary
If input port is configured as Close Mains
Mains/Gens
1
When transferring load from mains to generator, controller begins detecting “fail to transfer”, then the
open delay and transfer rest delay will begin. When detecting time out, if switch open failed, the
generator will not switch on, otherwise, generator switch on. Detecting transfer failure while gens
switch on. When detecting time up, if switch on fail, it is need to wait for generator to switch on. If
transfer failed and warning“SELECT Enable”, there is alarming signal whatever switch on or off
failure.
The way to transfer from generator load to mains load is as same as above.
�
2
Note: the above is in the middle position switch.
/Gens Auxiliary
If input port is not configured as Close Mains
Mains/Gens
Mains load be transferred into gens load, after switch off and transfer interval delay, gens switch on.
The way to transfer gens load to mains load is as same as above.
� Note: The above configuration is for an no-air-hang type ATS. But it can also be used for an
air-hang type ATS.
When controller is in Manual mode, manual transfer will be executive. After the generator normal starting,
when mains failure or remote start input is valid, mains switch off, then gens switch on.If you have
configured closing state input, during switching transitions also need to check the input state of closing
signals. If fail to close or open it will generate an alarm.
LXC6
10 Switch control procedures
3.3.2.LXC6
LXC61
3.3.2.
Auto control procedures,
When controller is in manual test, auto or stop mode, switch control procedures will start auto transfer.
After the generator starting successfully, gens switch on. When the remote start signal fail, gens switch
off.
If input port is configured as Close Mains Auxiliary,Gens load is transferred into generator un-load, after
the delay of switch off, detecting transfer failure while switch off output. When detecting time up, if switch
off failed, to wait for switch off. Otherwise, switch off is completed. Gens unload is transferred into gens
load, after the delay of switch on, detecting transfer failure while switch on outputting. When detecting
time up, if switch on failed, to wait for switch on. Otherwise, switch on is completed.If transfer failed and
warning “SEL Enable”, there is alarming signal whatever switch on or off failure.
If input port is not connected with closing breaker signal
signal,gens un-load is transferred into gens load,
gens switch on and output. Gens load is transferred into gens un-load, gens switch off and output.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
10 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Manual control procedures
procedures::
When controller is in Manual mode, manual transfer will be executive:
After the generator starting successfully,when remote start input is active, gens switch.on.When gens is
on load, if the remote start input fail, it will not uninstall or shutdown. But uninstall or shutdown will happen
when the conversion to automatic mode or pressing the Stop button . If you have configured the switch
status input, you also need to check the input state of signals. If fail to close it will generate an alarm.
、wireless remote control
4. SMS remote control
control、
This feature allows users to use GSM mobile communication terminal device for remote control.When
generators are running , if you want to stop the genset unit, you can send text messages to mobile phone
code“ SMS STOP MODE”. When the controller return code “SMS STOP MODE OK”, it means that genset
has got the command and try to stop.
follows::
SMS Code is described as follows
NO.
SMS Command
Description
1
SMS STOP MODE
2
SMS MANUAL MODE Set as manual mode
3
SMS TEST MODE
Set as trial test mode
4
SMS
Set as auto mode
5
SMS START
AUTO MODE
Set as stop mode
Start in manual or auto mode
Query command, query the current state of the controller:
item
Description (controller user custom description,
feirui1234567890abcd
can only be defined on the PC software)
6
�
SMS GENSET
Working mode
Working state
Mains (without the LXC620)
Gens voltage
Gens frequency
Oil pressures
Temperature
Level Fuel
Battery voltage
MANUAL MODE
GENSET AT REST
MAINS=230V
GENS=230V
F=50.0Hz
OPS=4.35Bar
WTP=55C
FLE=85%
BAT=27.5V
Note:
Note:Write text messages are not case sensitive, but must be written in strict accordance with the
instructions in the format, the spaces between all the words are a bit of spaces, all commands have to
wait until the return code indicates that the operation is valid only.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
11 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
5. Based on the GPRS DTU remote online monitoring
�
The scheme is based on LXI680G provide wireless data transmission network, remote control
operation of the generator on the Internet; and through the increase in the generator controller
LXI680G Room communication protocol, so that the controller can the use of LXI680G SMS via SMS
to control the generator run and generators receive alarm SMS.
�
Remark:LXI680G is Dongguan Feirui Electronics Co.,Ltd designed tailor-made for the generator
controller wireless data transmission module, in particular to optimize the data exchange between the
controller and the DTU, truly a fast and reliable data transmission.
�
Brief introduction:LXI680G is an industrial grade with GPS global satellite positioning function GPRS
DTU product. The product integrates a high-performance, low-power industrial-grade GPS module
and GPRS module, GPS global positioning technology and GPRS wireless communication
technology the perfect combination of a product.
�
LXI680G platform based on ARM and embedded operating system, built-in industrial-grade module, it
can be used in harsh environments, working temperature range can be up to -40℃ ~ + 85℃.LXI680G
provide standard RS232 serial interface, can be quickly and PLC, industrial control, instruments,
meters, RTU equipment is linked together, through the GPRS network will be linked to LXI680G
equipment data transmission to a host on the Internet, realize the data remote transparent
transmission, at the same time to the front-end equipment of GPS location information reported to
host, realize positioning of the equipment.
�
LXI680G with positioning, wireless data communications and data processing capabilities in a
compact, rugged, reliable, easy to install, can be widely used in construction, transportation and other
industries. Particularly suitable for tower crane monitoring, heavy machinery management, but also
can be used in the field of taxi operations management, transport vehicles, special vehicles, vehicle
rental management and leasing.
WIRELESS CONNECTION SCHEMATIC DIAGRAM
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
12 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
5.1. DTU with the binding of the controller
Controller and LXI680G after binding, it is only through the password to unbundling, if forced the controller
and the DTU apart, the controller will record the alarm and displayed on the LCD panel and the warning
information, or refuse the next start generator (the user can set up the binding deal) after failure, this
feature is especially suitable for generator leasing industry.
Multilevel password management
Users need to configure the parameters,through different permissions password input, the parameters of
the controller will present different configuration interface.
N
o.
1
2
3
Password
type
manager
technician
Dynamic
password
Extend of
competence
Password
modification
Unbound
Parameter
configuration
All change
permissions
(dynamic
password
Based on the
password
And the
application
code
For calculating
income)
Only have the
parameter
Configure
permissions
(not can
unbound)
Disposable(on
ly has a
one-time
password
Parameter
configure
permissions,
and
unbound)
can’t change
password
LXC620 User Manual
�: T:+86-769-23836636
Password
Managers
Deadline
Leasing
companies
Long
time
Leasing
Long
Companies、
time
Client
Dynamic
calculations
(Dynamic
code
providedby
The
customer)
Certain
time
effectively
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
13 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
5.2. Password generation and change the interface
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
14 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
6. History query
6.1. Event log
In the control panel, press
keys to view controller before abnormal shutdown record, including the time
of the outage warning content display and the state,press
according to state controller real-time show press
downtime record recently.
keys can search record back.Return
key again.LXC620 controller can record99 abnormal
6.2. History alarm
Controller will record the momentary generator all monitoring parameters. Users can remote access,easy
to cause analysis,due to a single record data is more, the record can only be through monitoring software
review,monitoring software can be through the DTU wireless remote read data.
Record reading window
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
15 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Recorded data display window
7. Protection
7.1. Warnings
When the controller detects warning signal,controller only warning does not stop,and the LCD display a
warning alarm type.
The following table warning volume controller:
No.
Warning type
1
High Temp.Warn
2
Low oil pressure
warn
3
Over Speed Warn
4
Under Speed Warn
5
6
7
Loss of Speed
Signal Warn
Over Frequency
Warn
Under Frequency
Warn
8
Over Voltage Warn
9
Under Voltage Warn
Description
When controller detects the temperature is higher than the set value, it
will send a warn alarm signal and it will be displayed in LCD.
When controller detects the oil pressure is lower than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
When controller detects the speed is higher than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
When controller detects the speed is lower than the set value,it will send
a warn alarm signal and it will be displayed in LCD.
When controller detects the speed is 0 and the action select"Warn", it will
send a warn alarm signal and it will be displayed in LCD.
When controller detects the frequency is higher than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
When controller detects the frequency is lower than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
When controller detects the voltage is higher than the set value,it will
send awarn alarm signal and it will be displayed in LCD.
When controller detects the voltage is lower than the set value,it will
send awarn alarm signal and it will be displayed in LCD.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
16 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
When controller detects the current is higher than the set value,it will
send awarn alarm signal and it will be displayed in LCD.
When generator can not stop after the“stop delay”/”ETS delay”,
11 Fail to Stop
controller will send warning alarm signal and it will be displayed in LCD.
When controller detects the oil lever is lower than the set value,it will
12 Low Level Warn
send a warn alarm signal and it will be displayed in LCD.
When controller detects the charger voltage is lower than the set value,it
13 Charge Alt Fail
will send awarn alarm signal and it will be displayed in LCD.
Battery Under
When controller detects the battery voltage is lower than the set value,it
14
Voltage
will send a warn alarm signal and it will be displayed in LCD.
Battery Over
When controller detects the battery voltage is higher than the set value,it
15
Voltage
will send a warn alarm signal and it will be displayed in LCD.
Auxiliary input port
When digit input port1-6is set as warning and active,controller sends
16
1-6warning
corresponding warning signal.
Note: the auxiliary input port warning types,must be user configuration,to be effective.
10
Over Current Warn
7.2. Shutdown alarm
When controller detects shutdown alarm,it will send signal to stop the generator to load out,and the
Display alarm type.
Shutdown alarms as following:
No
No..
Warning types
1
Emergency Stop
2
High Temperature
3
Low Oil Pressure
4
Over Speed
5
Under Speed
6
Loss Of Speed
Signal
7
Over Frequency
8
Under Frequency
9
Over Voltage
10
Under Voltage
11
Over Current
12
Fail To Start
13
Oil Pressure
Sensor Open
14
Input Port 1-6
Description
When controller detects emergency stop signal,it will send a stop alarm
signal and it will be displayed in LCD.
When controller detected the temperature of water/cylinder is higher than
preset,it will send a stop alarm signal and it will be displayed in LCD.
When controller detected oil pressure is lower than the preset,it will send
a stop alarm signal and it will be displayed in LCD.
When controller detected genset speed is over the preset,it will send a
stop alarm signal and it will be displayed in LCD.
When controller detected genset speed is under the preset,it will send a
stop alarm signal and it will be displayed in LCD.
When controller detected genset speed is 0,it will send a stop alarm
signal and it will be displayed in LCD.
When controller detected genset frequency is over the preset,it will send
a stop alarm signal and it will be displayed in LCD.
When controller detected genset frequency is under the preset,it will send
a stop alarm signal and it will be displayed in LCD.
When controller detected genset voltage is over the preset,it will send a
stop alarm signal and it will be displayed in LCD
When controller detected genset voltage is under the preset,it will send a
stop alarm signal and it will be displayed in LCD
When controller detected genset current is over the preset and delay is
not0,it will send a stop alarm signal and it will be displayed in LCD
During the start at tempt times, if genset start failed, it will send a stop
alarm signal and it will be displayed in LCD
When oil pressure sensor opens circuit and the input is active,controller
will send a stop alarm signal and it will be displayed in LCD.
When controller detected the input port1-6external warning is active,
controller will send shutdown alarm signal and it will be displayed in LCD.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
17 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Note: the input port shutdown alarm types,must be user configuration,to be effective.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
18 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
7.3. Trip alarm
When controller detects shutdown alarm signal,it will shutdown generator quickly and stop after high
speed cooling.
Trips shutdown alarm as following:
No
No..
Warning type
Detection range
1
Over Current
Remain valid
2
Input port1-6
The user setting
range
Description
When controller detects the value is higher thant he set
value, and the action select"trip and shutdown",it will send
a trip alarm signal and it will be displayed in LCD.
When digital input port1-6 is set as"trip and shutdown",
and the action is active,it will send atrip alarm signal and it
will be displayed in LCD.
Note: the input port trip alarm types,must be user configuration,to be effective.
7.4. SMS alarm
These items are sent via SMS to the user to set the GSM mobile communication terminal.
No.
Condition
1
2
3
4
5
6
7
8
9
10
11
Emergency stop
High temperature1 shutdown
Low oil pressure1shutdown
Over speed shutdown
Under speed shutdown
Speed signal loss shutdown
Over frequency shutdown
Under frequency shutdown
Over voltage shutdown
Under voltage shutdown
Over current shutdown
Starting failure shutdown
Oil pressure sensor open shutdown
Input 1 shutdown
Input 2 shutdown
Input 3 shutdown
Input 4 shutdown
Input 5 shutdown
Input 6 shutdown
Over current trip alarm
Input port 1 trip alarm
Input port 2 trip alarm
Input port 3 trip alarm
Input port 4 trip alarm
Input port 5 trip alarm
Input port 6 trip alarm
High temperature 2 shutdown
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
19 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
28
Low oil pressure 2 shutdown
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
20 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
8. Parameter setting
Date and time setting:
In the controller start and press
and
In the controller start and press.The interface will display two
lines,date and time,the current date and time display, second user be havior modification status
display,the black display digital for current user can modify the number, press the + key and key changes
to the digital reverse black display ,press button can be modified to confirm and tick to the right
one.intermediate parentheses 1 week display,which is composed of microprocessor based on the current
set date calculated,the user does not need to be amended.
Date/Time Setting Current time:
08-10-27 (1) 08:27:55
08-10-27 (1) 08:27:23
parameters::
Operating parameters
Pressed on the controller start
and
,Enter the password to confirm the parameter configuration
interface, press the+ key or key input corresponding password value 0-9,bit shift by button,press the ball
bond in position fourth,password checking,the password is correct according to the parameters of the
main interface of different access password to enter different permissions, password error directly from
the.(factory default password is : 0000) the factory default password users can modify.Press the+ key and
key parameters can be configured on the screen turning operations, according to tick button on the
configuration parameters screen under the present,into the current configuration mode,the current values
of the first black display, press the+ key or button for the numerical adjustment,shift by√button,the last one
to tick button to confirm this setting. The value is stored permanently to the control device of FLASH.
Parameter configuration
1Mains voltage is normal delay
Range:(0-3600)s
0060
�
Note:
Note:In the setup process,any time according to
Key can immediately interrupt the current setting
of parameters,and returns the operation of standby.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
21 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
8.1. Parameter setting,content and scope of list
Menu
01 Low oil pressure1(warning)
02 Low oil
pressure1(shutdown)
03 High temperature1(warning)
04 High
temperature1(shutdown)
05 Fuel level (warning)
06 Start delay
07 Stop Delay
08 Cranking time
09 Crank Rest Time
10 Safety On Delay
11 Over Speed Delay
12 Start Idle Time
13 warm-up Time
14 Switching Transfer time
15 Return time
16 Cooling time
17 Stop idle time
18 ETS Solenoid Hold
19 Fail To Stop Delay
20 Gens transient Delay
21 Mains transient Delay
Range
(1-399)kPa
Default
124kPa
(0-398)kPa
103kPa
(81-139)℃
90℃
(82-140)℃
95℃
(0-100)%
(0-9999s)
(0-300s)
(3-60s)
(3-60s)
(5-60s)
(0-10s)
(0-3600s)
(0-3600s)
(0-600s)
(0-9999s)
(0-3600s)
(0-3600s)
(0-120s)
(10-120)s
(0-30s)
(0-30s)
10%
5s
0s
5s
10s
10s
2s
10s
30s
2s
30s
60s
10s
20s
30s
5s
2s
22 Mains Under Voltage( Trip) (50-360V/624) *1
184V
23 Mains Over Voltage( Trip)
(50-360V/624) *1
276V
(0-75Hz )
45.0Hz
(0-75Hz)
55.0Hz
(50-360V/624)
184V
24 Mains Under Frequency
( Trip)
25 Mains Over
Frequency( Trip)
26 Gens Over Voltage
(Shutdown)
27 Gens Under Voltage
(Warning)
28 Gens Over Voltage
(Warning)
29Gens Over Voltage
(Shutdown)
30 Gens Under Frequency
(Shutdown)
31 Gens Under Frequency
(Warning)
Timer
Returns: the return value of 207V >
under voltage trip value
Returns: the return value of 207V<
Over voltage trip value
Returns: the return value of 48.0Hz
>under Frequency trip value
Returns: the return value of
52.0Hz<over Frequency trip value
(50-360V/624)
196V
Load values:207V
Gens under voltage setting : stop
value < warning value < load value
(50-360V/624)
265V
Return value:253V
(50-360V/624)
273V
Gens voltage setting : stop value >
warning value > return value
(0-74.8 Hz)
40.0Hz
(0.1-74.9 Hz)
42.0Hz
LXC620 User Manual
�: T:+86-769-23836636
Description
Return value:138kPa
Low oil pressure 1 setting : stop value
< warning value < return value
Return value:88℃
High temperature1setting : stop
value>warning value>return value
Analog
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Timer
Load values: 45.0Hz
Gens under frequency setting: stop
value < warning value < load value
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
22 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
32 Mains Over Frequency
(Warning)
(0.1-74.9 Hz)
55.0Hz
Return value:52.0Hz
33 Mains Over Frequency
(Shutdown)
34 Over current
35 Flywheel Teeth
36 Under speed (shutdown)
(0.2-75 Hz)
57.0Hz
(50-120%)
(10-500 )
(0-5998RPM)
100%
118
1270RPM
37 Under speed(warning)
(1-5999RPM)
1350RPM
Return value: 1380RPM
Gens under speed setting : stop value
< warning value < load value
38 Over speed(warning)
(1-5999RPM)
1650RPM
Return value:1620RPM
39 Over speed(shutdown)
(2-6000RPM)
1710RPM
Gens over speed setting : stop value >
warning value > return value
(0-10%)
0
Numerical simulation
41 Battery Under Voltage
(warning)
(0-39.9 V)
8.0V
Numerical simulation
42 Battery Over Voltage
(warning)
(0.1-40V)
33.0V
Numerical simulation
(0-39V)
6.0V
Numerical simulation
(0-1)
0
(0-9999)
(1-399)kPa
0000
Not used
40 Over speed shoot
43 Charging failure (warning)
44 Language
45 Password Settings
46 Low oil pressure2 (warning)
47 Low oil pressure 2
(shutdown)
48 High temperature 2
(warning)
49 High temperature 2
(shutdown)
50 Current transformer
51 Oil pressure1sensor
52 Temperature1sensor
53 Fuel level sensor
54 Oil pressure2 sensor
55 Temperature2sensor
56 Module Address
57 Temperature unit selection
58 Pressure units election
59 Phone number 1
60 Phone number 2
61 Phone number 3
0 :Chinese :ENGLISH
(0-398)kPa
Not used
(81-139)℃
Not used
(82-140)℃
Not used
5-6000:5A
1-14
1-13
500A
VDO10 bar
VDO 120 ℃
VDO
ohm(10-180)
Not used
Not used
1
℃
kPa
----------------------------------------------
1-11
1-13
1-12
1-254
0-1
0-1
Most 16
Most 16
Most 16
Gens over frequency setting:stop
value > warning value > return value
Numerical simulation
Numerical
Low oil pressure 2 threshold setting
specification: stop value < warning
value < return value
High temperature 2 setting : stop
value > warning value > return value
Load value: 500A
Temperature sensor 2 effective
Oil pressure sensor 2 effective
Set of numbers, such as China need
to add the area code 8613666666666
Note: 1: 360V phase voltage, 624V line voltage (three-phase three-wire).
2: low pressure (Shutdown) set the value to 0,does not stop.
3: High temperature (down) set the value to 140, does not stop.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
23 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
The remaining parameters configuration: only by the PC software configuration
(see the table below)
Parameter name
Factory Defaults
Alternator select
Yes
Generator Poles
Speed sensor select
4
Yes
3 phase 4 wire
Not
3
No action (only LXC620)
Not
Not
From pre-heat output to start
High water temperature input, shutdown, close to activate
(from safety on over).
Low oil pressure input, shutdown, close to activate
(from safety on over).
AC Power Supply
Fast loading mode
Crank Times
Enable immediate mains dropout
Volt Transformer
Fuel pump control
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Digital Output 1
Digital Output 2
Digital Output 3
Digital Output 4
LED1 configuration
LED2 configuration
LED3 configuration
LED4 configuration
Time Multiplier
Over Current Action
Low oil level input, warning, close to activate, (always activate).
High oil temperature input, shutdown, close to activate
(from safety on over).
External alarm input, shutdown, close to activate
(always activate).
From pre-heat output to start
Common alarm
ETS solenoid output
Idle /High speed control
The system in automatic mode
Common to Start Alarm
Common shutdown alarm
Common alarm
36
Trip shutdown
Gens Freq. Of Crank Disconnect
15Hz
Gens Speed Of Crank Disconnect
Gens Oil Pressure Of Crank
Disconnect
Starting Oil Pressure Detect
Genset regular star
SMS function is activated
Phone number1-5
450RPM
Digital Input 5
Digital Input 6
Not use
Yes
No
Yes
No
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
24 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
4
8.2. Programmable output port can be defined content table1table1-4
Type
No.
1 Not used
2 throttle control
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29-3
35
36
37
38
39
40
41
42
43
44
45
46
47
Function Description
Alarm stop and emergency stop action in overdrive, close the door.
The warning, stop, electric tripping action, can be an external alarm,
audible alarm
configurable input port " alarm silence " effective, may prohibit its output.
The battery voltage is too high The battery voltage too high alarm action.
The battery voltage is too low Warning alarm when the battery voltage is too low.
save
save
save
Starting relay output
Generator starting action, after successful starting off.
Fuel relay output
Generator startup action, wait stop disconnect.
Boot time effectively
Boot time running effective action, no action is invalid.
Charge failure
Charging generator failure alarm action.
Gens switch close
Can control the generator switch with overload.
Pulse generator switch output, the output time from the closing
Gens Pulse switch close
time of the control pulse.
Mains switch close
Can be controlled mains switch with overload.
Mains Pulse switch close
Mains switch output pulse, the pulse output time from the closing time control.
Public under frequency
Generator under frequency frequent shutdown alarm action.
frequent shutdown alarm
Public under frequency
Generator under frequency frequency alarm action.
frequency alarm
Public under voltage
Generator under voltage shutdown alarm action.
overvoltage shutdown alarm
Generator under voltage
Generator under voltage alarm action.
shutdown alarm action.
Public alarm
Generator public warning, public parking, public electrical trip alarm action.
Public trip alarm
Public trip alarm action.
Public shutdown alarm
Public shutdown alarm action.
Public warning alarm
Public warning alarm action.
High temperature 1 warning alarm action.
High temperature 1 warning
High temperature 1 shutdown alarm High temperature 1 shutdown alarm action.
The ongoing heat delay
The ongoing heat delay action.
save
Input port 1-6
Input port 1-6 effective action.
Emergency shutdown alarm
Emergency shutdown alarm action.
ETS output
Time delay in the ETS within the movement.
Starting failure alarm
Starting failure alarm action.
The fuel level upper and lower limit to control its motion.
Fuel pump control
Gens effective
The generator cooling during normal operation and high-speed action.
Gens Over Frequency Warning Gens over frequency warning action.
Gens over frequency shutdown Gens over frequency shutdown has occurred.
alarm overvoltage warning
Gens
Gens overvoltage warning action.
Gens overvoltage shutdown
Gens overvoltage shutdown action.
Gens under frequency
Gens under frequency warning action.
warning
Gens under frequent
Gens under frequency when stopping action.
shutdown
Gens under voltage warning action.
Gens
under voltage warning
Gens under voltage shutdown Gens under voltage shutdown action.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
25 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
48 Louver Control
49 Low fuel level
50 Speed signal loss
Action in genset starting and disconnect when genset stopped completely.
Low fuel level action.
In safe operation, the engine speed detection equal to 0 action.
Mains over and under frequency, overvoltage, under voltage,
51 Mains abnormal
auxiliary mains abnormal input effective action.
52 Mains Over Frequency
Mains over frequency when the action.
53 Mains overvoltage
Mains overvoltage action.
55 Mains under frequency
Mains under frequency action.
56 Mains under voltage
Mains under voltage action.
57 Low oil pressure of 1 warning Low oil pressure warning action 1.
58 Low oil pressure 1 shutdown
Low oil pressure shutdown action 1.
59 Oil pressure sensor open
Oil pressure sensor open action.
60 Gens switch open
Can control the switch to gens the unloading.
Gens pulse switch output, output time divided by the gate pulse
61 Gens Pulse switch open
time control.
Can control the switch to electric discharge.
62 Mains switch open
Mains pulse switch output, output time divided by the gate pulse
63 Mains Pulse switch open
time control
64 Over current warning
Generators over-current warning action.
Generators over-current tripping action.
65 Over current trip
Engine over speed warning action
66 Over speed warning
Engine overspeed shutdown alarm action.
67 Over speed shutdown
68 Preheating to start
Action from the preheating time delay to the start time.
From the preheating time delay to the starting end for movement
69 Preheating to start over
between.
Preheat the oven to warm the From the preheating time delay to the starting end for movement
70
end
between.
Preheating
to
the
safe
From
the end of a preheating time delay to the safe operation,
71
operation of the end
action.
72 switch open output
The switch is controlled to make electricity or power generation unloading.
73 In manual mode
System in the manual test machine mode of action.
74 System in automatic mode
System in the automatic mode of action.
75 The system is in manual mode In manual mode of action.
System shutdown mode of action.
76 System shutdown mode
77 Under speed warning
The engine under speed warning action.
78 Less speed down
engine under speed stop action.
In the automatic mode, the generator during normal operation,
Automatic stop prohibited
79
when the automatic shutdown disable input effective action.
In the start and stop idle waiting for the boot idling stop time
80 Idle / high speed control
during operation action.
81 Pre-oil Supply Output
Action from“crank on”to“safety on”.
82 Raise Speed
Action in hi-speed warming run.
Output in start period. If there is no gens frequency during hi-speed
83 Excite Generator
running, output 2 seconds again.
84 Drop Speed
Action in period of stop idle mode to time of wait for stopping completely.
85 Pre-Lubricate
Actions in period of pre-heating to safety run.
82 High temperature2 warning
Action when high temperature2warning alarm.
83 High temperature2 shutdown Action when high temperature2shutdown alarm.
84 Low oil pressure2 warning
Action when low oil pressure 2 warning.
85 Low oil pressure2 shutdown
Action when low oil pressure 2. shutdown.
Note: Output port 1 - 4 can be configured to use computer software
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
26 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
8.3. Programmable input port 1-6 definition content list
No.
Type
Function Description
Including following functions:
-------------------------------------------Warning: warn only, not shutdown.
Shutdown: alarm and shutdown immediately.
Trip and stop: alarm, generator unloads and shutdown after
hi-speed cooling.
Trip: alarm, generator unloads but not shutdown.
Indication: indicate only, not warning or shutdown.
-------------------------------------------From safety on: detecting after safety on run delay.
From crank: detecting as soon as start.
Always: input is active all the time.
Never: input inactive
1
Users Configured
2
3
Alarm Mute
Reset Alarm
4
Inhibit Auto Stop
5
Aux Mains Fail
Can prohibit“Audible Alarm”output when input is active.
Can reset shutdown alarm and trip alarm when input is active.
In Auto mode, during generator normal running, when input is active, inhibit
generator shutdown automatically.(This function is only LXC620)
In Auto mode,mains are abnormal when input is active.
6
Aux Mains Closed
Connect mains loading switch is Aux.Point
7
Aux Gens Closed
Connect generator loading switch's Aux. Point.
8
Inhibit Mains Load
When the input is valid, Forbidden City electric load, has been loaded
immediately uninstall.
9 Lamp Test
10 Aux Mains Closed
11 Inhibit Mains Load
12 Panel key ban
13
Remote Start(Not
On Load)
14
Remote Start(on
Load)
15 Inhibit Scheduled
16 Aux Mains OK
All LED indicators are illuminating when input is active.
Connect mains loading switch is Aux.Point.
When the input is valid, Forbidden City electric load,has been loaded
immediately uninstall.
When the input is valid,the panel all keys do not its role, the panel LCD
The first screen the first line on the right shows.
In the automatic mode,when the input is valid, and can automatically open
the turbine, generator normal operation is not loaded. When the input is
invalid, can automatically stop generating set.
In the automatic mode,when the input is valid, and can automatically open
the turbine, generator normal operation after loading. When the input is
invalid, can automatically stop generating set.
In Auto mode,inhibit scheduled run genset when input is active.
In Auto mode,mains are normal when input is active.
8.4. Custom project name list
No.
1
2
3
4
Type
High Water Temperature Input
Low Oil Pressure Input
High Oil Temperature Input
Box High Temperature Input
Description
When active,the panel displays the high water temperature input alarm.
When active,the panel displays the low oil pressure input alarm.
When active,the panel displays the high oil temperature input alarm.
When active,the panel displays the box high temperature input alarm.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
27 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
5
6
7
8
9
10
Low Level Input
Low Oil Level Input
Over Speed Input
External Alarm Input
Over Current Input
Half Oil Level Input
11 Monitor Mode Input
When active,the panel displays the low level input alarm.
When active,the panel displays the low oil level input alarm.
When active,the panel displays the over speed input alarm.
When active,the panel displays t he external input alarm.
When active,the panel displays the over current input alarm.
When active,the panel displays half the oil level level input alarm.
When active,the panel display system in the monitor mode,only
the genset electric monitoring parameters and alarm signal(low
speed,low voltage alarm is not monitored)
Note: The input port 1-6,only use computer software to configure.
8.5. Sensor selection list
No.
1
2
3
entry
Content
Remarks
1 Do not use
2 digital input low effective
3 digital input high effective
4 VDO 120 degrees C
5 Datcon high
6 Datcon low
temperature sensor 7 SGX 120 degrees C
8 Cummins
9 SGH 120 degrees C
10 Curtis
11 SGD 120 degrees C
12 Pt100
13 User defined
1 Do not use
2 digital input low effective
3 digital input high effective
4 VDO 5 bar
5 VDO 10 bar
6 Datcon 5 bar
7 Datcon 10 bar
pressure sensor
8 Datcon 7 bar
9 SGX 10 bar
10 CMB812
11 SGH 10 bar
12 Curtis
13 SGD 10 bar
14 User defined
1 Do not use
2 digital input low effective
3 digital input high effective
4 VDO Ohm range (10-180)
5 VDO Tube type (90-0)
fuel level sensor
6 US Ohm range (240-33)
7 GM Ohm range (0-90)
8 GM Ohm range Ohm range (0-30)
9 Ford (73-10)
10 NKZR12/24-1-04 Ohm range (100-0)
11 User defined
LXC620 User Manual
�: T:+86-769-23836636
Custom resistive input
resistance range of
0-999 Europe, silently
think factory VDO 120
degrees C curve. User
defined temperature
curve through the PC
software settings.
Custom resistive input
resistance range of
0-999 Europe, the
factory silence that
VDO 10 bar curve.
User defined pressure
curve through the PC
software settings.
Custom resistive input
resistance range of
0-999 Europe, the
factory silence that
VDO 10 bar curve.
User defined pressure
curve through the PC
software settings.
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
28 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
8.6. Conditions of crank disconnect selection
No.
0
1
2
3
4
5
6
Setting description
Speed sensor
Gen frequency
Speed sensor +Gen frequency
Oil pressure sensor
Speed sensor
Gen frequency +Oil pressure sensor
Gen frequency +Speed sensor+Oil pressure sensor
�
There are 3 conditions to make starter disconnected with engine, that is, speed sensor, generator
frequency and engine oil pressure. They all can be used separately. We recommend that engine oil
pressure should be using with speed sensor and generator frequency together, in order to make the
starter motor is separated with engine immediately and can check crank disconnect exactly.
�
Speed sensor is the magnetic equipment which be installed in starter for detecting flywheel Teeth.
�
When set as speed sensor, must ensure that the number of flywheel teeth is as same as setting,
otherwise,“over speed stop”or“under speed stop” may be caused.
�
If genset without speed sensor, please don t select corresponding items, otherwise, “start fail” or
“loss speed signal”maybe caused.
�
If genset without oil pressure sensor, please don ‘t select corresponding items.
�
If not select generator in crank disconnect setting, controller will not collect and display the relative
power quantity (can be used in water pump set); if not select speed sensor in crank disconnect
setting, the rotating speed displayed in controller is calculated by generator frequency and number of
poles.
9. Wirings connection
The back panel of LXC620 controller is shown as below:
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
29 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
Back panel terminal block wiring description
description:
No.
Functions
Diameter
Remark
DC negative input ,connect to negative of starter battery.
DC positive input,connect to positive of starter
battery.(20Afuserecommended).
Charging D+ input, do not connect to ground
Switch to B-.
1
DC input B-
1.5mm
2
DC input B+
1.5mm
3
4-9
10
11
Charge failure input /excitation
Aux. Input 1-6
Magnetic Pickup +
Magnetic Pickup-
1.0mm
1.0mm
1.0mm
1.0mm
12
Magnetic Pickup
1.0mm
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Temperature 2 Sensor Input
Oil Pressure 2 Input
Fuel level sensor input
Temperature 1 sensor input
Oil pressure 1 sensor input
Sensor COM
RS485RS485+
RS485 COM
1.0mm
1.0mm
1.0mm
1.0mm
1.0mm
1.0mm
0.5mm
0.5mm
0.5mm
Aux. Output 4
1.0mm
Free voltage contacts.16Amprated
Aux. Output 3
1.0mm
Free voltage contacts.16Amprated
Aux. Output 2
Aux. Output 1
Start relay output
Fuel relay output
1.0mm
1.0mm
1.5mm
1.5mm
B+output,rated 10A.
B+output,rated 10A.
31
Emergency stop
2.5mm
32
33
34
35
36
37
38
39
40
41
CT Secondary A Sensing
CT Secondary B Sensing
CT Secondary C Sensing
CT Secondary Common
Generator A Volt Sensing
Generator B Volt Sensing
Generator C Volt Sensing
Generator Neutral Input
Mains Phase A Volt Sensing
Mains Phase B Volt Sensing
1.5mm
1.5mm
1.5mm
2.5mm
1.0mm
1.0mm
1.0mm
1.0mm
1.0mm
1.0mm
42
Mains Phase C Volt Sensing 1.0mm
43
44
Mains Neutral Input
USB Connector
1.0mm
Connect to Magnetic Pickup device.
Common ground,which can be accessed chassis or
starter battery negative.
Connect to Temperature Sensor.
Connect to Oil pressure 2 sender.
Connect to fuel level sensor.
Connect to Temperature sender.
Connect to Oil pressure sender.
Public terminals of sensor,(B-) have already. connected.
Impedance-120Ω shielding wire is recommended, its
single-end earthed.
B+ is supplied by 31 points, rated16A.
Plant Supply B+.Also supplies fuel&start Outputs.
(Recommendedmaximum20Afuse).
Connect to secondary of A (maximum 5A)
Connect to secondary of B (maximum 5A)
Connect to secondary of C (maximum 5A)
Common GND, connecting to start battery negative.
Connect to generator A output (Recommend 2A fuse)
Connect to generator B output (Recommend 2A fuse)
Connect to generator C output (Recommend 2A fuse)
Connect to generator N line terminal.
Connect to mains A output (Recommend 2A fuse)
Connect to mains B output (Recommend 2A fuse)
Connect to mains C output (Recommend 2A fuse)
(Recommend 2A fuse)
Connect to mains neutral terminal
USB and computer communication(maximum4)
NOTE: Prohibited during operation of the engine starter batteries removed, otherwise it will cause
the control system due to excessive DC input voltage and burned!
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
30 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
10. Typical applications
�
GPRS MODEM recommended Dongguan Feirui Electronics Co., Ltd. is equipped with ( need to buy
separately ), RS232 Communication lines connected correctly according to the figure.
�
If the engine starter battery voltage is 24V, output, measuring starting fuel outlet and stop outlet
(depending on the user configuration ) of negative electrode resistance should not be less than 2 ohm,
if less than 2 ohms in the output port and extend current greater than 30A relay. If the engine starter
battery voltage is 12V, output, measuring starting fuel outlet and stop output port on the battery
negative resistance should not be less than 1 ohm, if less than 1 ohm in the corresponding output port
and extend current greater than 30A relay.
Three-phase three-wire connection wiring diagram (to LXC620 example)
Single-phase two-wire connection wiring diagram (to LXC620 example)
Two-phase three-wire connection wiring diagram (to LXC9220 example)
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
31 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
LXC620 Typical application diagram
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
32 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
LXC6
10 Typical application diagram
LXC61
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
33 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
11. Installation
11.1. Case dimension and fixing size
LXC620 Controller is panel built-in design; it is fixed by clips when installed. The controller’s overall
dimensions and cutout dimensions for panel, please refers to as following.
Case Dimension
Cut Out
11.2. Battery voltage input
LXC620 series controller can suit for widely range of battery voltage (8~35)VDC. Negative of battery must
be connected with the shell of starter stable.The diameter of wire which from power supply to battery must
be over 2.5mm 2. If floating charge configured, please firstly connect output wires of charger to battery’s
positive and negative directly,then,connect wires from battery’s positive and negative to controller’s
positive and negative input ports in order to prevent charge disturbing the controller’s normal working.
11.3. Speed sensor input
Speed sensor is the magnetic equipment which be installed in starter and for detecting flywheel teeth.Its
connection wires to controllershouldapplyfor2coresshieldingline. The shielding layer should connect with
No.16terminalin controller while another side is hanging in air. The else two signal wires are connected
with No.17andNo.18terminalsin controller. The output voltage of speed sensor should be
within(1~24)VAC(effective value)during the full speed.AC12Vis recommended (in rated speed).When
install the speed sensor,let the sensor is spun to contacting flywheel first,then,port out1/3lap, and lock the
nuts of sensor at last.
11.4. Output and expand relays
All outputs of controller are relay contact output type.If need to expand the relays,please add freewheel
diode to both ends of expand relay’s coils(when coils of relay has DC current) or, increase
resistance-capacitance return circuit(when coils of relay has AC current),in order to prevent disturbance to
controller or others equipment.
11.5. Ac input
LXC620 Current input of controller must be connected to outside current transformer. And the current
transformer’s secondary side current must be 5A. At the same time, the phases of current transformer
and input voltage must correct. Otherwise, the current of collecting and active power maybe not correct.
LXC620 User Manual
�: T:+86-769-23836636
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
34 of 35
LXC620 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
�
Note:
Note:a.ICOM port must be connected to negative pole of battery controller power.b.When there is
load current,transformer’s secondary side prohibit from open circuit.
a.ICOM port must be connected to negative pole of battery controller power.
Note
Note:a.ICOM
b.When there is load current,transformer
current,transformer’’s secondary side prohibit from open circuit.
11.6. Withstand voltage test
When controller had been installed in control panel,if need the high voltage test,pleased is
connect controller’s all terminal connections,in order to prevent high voltage into controller and damage it.
12. Common faults and exclusion method
Following in my company controller process more common failure and exclusion method,if there is a
failure of the other can not be solved,please contact my company.
Faults
Possible Solutions
Check starting batteries;
Check controller connection wirings;
Controller no response with power.
Check DC fuse.
Check the water/cylinder temperature is too high or not;
Check the genset AC voltage;
Genset shutdown
Check DC fuse.
Check emergence stop button is corrector not;
Check whether the starting battery positive be
Controller emergency stop
connected with the emergency stop input;
Check whether the circuit is open.
Low oil pressure alarm after crank disconnect Check the oil pressure sensor and its connections.
High water temp alarm after crank disconnect Check the temperature sensor and its connections.
Check related switch and its connections according to the
Shutdown Alarm in running
information on LCD; Check programmable inputs.
Check fuel oil circuit and its connections;
Check starting batteries;
Crank not disconnect
Check speed sensor and its connections;
Refer to engine manual.
Check starter connections;
Starter no response
Check starting batteries
Check ATS;
Genset running while ATS not transfer
Check the connections between ATS and controllers.
13. Product packaging
This product should be following sets
sets::
Dongguan Tuancheng Automation
Equipment Co.,LTD.
(1) 1 piece of controller model LXC620/LXC610.
(2) 4 pieces of fixed cards.
(3) 1 piece of product certificate.
(4) 1 piece of product manual.
LXC620 User Manual
�: T:+86-769-23836636
Tel:
Tel:+86-769-23836636
Fax:
Fax:+86-769-23166296
http:
http://www.lixise.com
http:
http://www.lixise.net
E-mail:
E-mail:sales@lixise.com
Add: Wentang Road, Chashang
industrial zone #18, Dongcheng,
Dongguan, Guangdong, China
Dongguan Tuancheng Automation Equipment Co.,LTD.
�: F:+86-769-23166296
� :www.lixise.com
Page
35 of 35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising