Abundant Flow Water Zoi DFK-MU, Zoi DFK-Pi Service Manual
Advertisement
Advertisement
Incoming TDS/Total Dissolved Solids not to exceed 2000 PPM.
Use of Vaseline or petroleum based lubricants will also void the warranty.
How Do I Receive Warranty Service?
If your system is found to be defective, first call for a returned merchandise authorization number (RMA#). Please provide a reason for the return and a date of purchase or invoice number if available.
Returns must be received within 15 days of the RMA# issue date. The buyer will be responsible for shipping costs to our warehouse, if a defect is found Abundant Flow Water will pay for return shipping, if no defect is found buyer will be responsible for return shipping as well.
Upon inspection, Abundant Flow Water will replace or repair, at our option, any parts found to be defective according to the terms of this warranty. If we choose to replace the equipment, we may replace it with reconditioned equipment. Parts used in repairing or replacing the equipment will be warranted for 90 days from the date the equipment returned to you or for the remainder of the original warranty period, whichever is longer. Returns received without a RMA number shall become the property of Abundant Flow Water. Customers who return items without a RMA # and contact us with details about the return will be responsible for return shipping, regardless of warranty covered defects.
LIMITATIONS AND EXCLUSIONS:
Abundant Flow Water will not be responsible for any implied warranties, including those of merchantability or fitness for a particular purpose or application. The purchaser and installer are responsible for checking fittings, lines, parts, and equipment for defects before installation. Abundant Flow Water will not be responsible for any incidental or consequential costs or damages incurred by installation of the system or loss of function of the system, including, but not limited to, water damage, leaks, inconvenience, travel expenses, telephone charges, loss of revenue, loss of time, loss of equipment usability, loss of life, property damage, or loss of finances. The purchaser and installer are responsible for checking the system for leaks or defects after installation. All responsibilities of Abundant Flow Water regarding this equipment are set forth in this warranty.
Zoi Series
RO System
Reverse Osmosis Water Filtration System
Core System Filter Set
DFK-Alpha
*
Typical Filter Life: 6-12 Months
Replacement Membrane
MB-1812-50F
†
Typical Membrane Life: 2-4 Years
www.afwfilters.com
* Set for core RO system; refer to chart for upgraded kits.
† Default membrane, upgraded systems may differ. i
Important Information
Date Purchased: ___________________________
Date Installed: ___________________________
Replacement filters available online: www.afwfilters.com
Maintenance Log:
Maintenance details are in the maintenance section.
Recommended replacement intervals are as follows:
Filters: Every 6 months for most homes, at least once a year
UB Lamp (if upgraded): Every 12 months*
O-rings: In conjunction with a filter change, every 1-2 years
Sanitization: Once a year, more often if bacteria present
Membrane: Varies from 2-4 years, at least every 4 years
Date Filters Replaced Lamp Sanitized Membrane
Parts List
1 Feedwater Adapter
2 Elbow 1/4”M x 1/4”QC
12 Elbow 1/8”M x 1/4”QC
13 Membrane Housing
3 10” Filter Housing 14 RO Membrane
4 10” Sediment Filter - 5 micron 15 Elbow Check 1/8’M x 1/4” QC
5 Hex Nipple
6 10” GAC Filter
7 10” Carbon Block - 5 micron
8 3 Canister Bracket
16 Capillary Flow Restrictor
17 Drain Saddle Valve
18 UV Filter - Optional
19 Tee - 1/4”QC
9 JACO Nut
10 Insert
11 Auto Shut Off
20 Tank Ball Valve 1/4”F x 1/4”QC
22 pH Filter - Optional
23 Alkaline Filter - Optional
24 Post Filter
25 Ice Maker Kit - Optional
26 Faucet Quick Connect
27 FlowLok Saftey Tray
28 FlowLok Saftey Shut-off
29 FlowLok Relacement Disc
30 Small Filter Clip - 2"x2"
31 Medium Filter Clip - 2"x2.5"
32 Large Filter Clip - 2.5"x2.5"
Abundant Flow Water 2261 Schoenchen Rd Pfeifer, KS 67660 www.afwfilters.com | [email protected] | 785-735-9769
Reverse Osmosis System Limited Warranty
Abundant Flow Water Systems, Inc.
What Does This Warranty Cover?
This warranty covers manufacturer defects on your Reverse Osmosis system (System). This includes filter housings, membrane housings, brackets, membranes, fittings, transformers, clips, check valves, flow restrictors, ball valves, storage tanks, faucets, adapters, drain valves, filter housing wrenches, tubing, and accessories included in your original order.
What Does This Warranty NOT Cover?
This warranty does not cover replaceable filters or other consumables
(excluding membranes). This warranty does not cover defects resulting from improper installation or installation contrary to printed instructions. This warranty does not cover defects that are the result of abuse, misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties, fire, flood, freezing, environmental factors, natural occurrences, unnatural occurrences, or acts of God. For warranty service, please call for return authorization number before returning items. No credit or exchange will be given without a valid RMA number. To obtain your authorization number, you will need to provide us with the reason for return, the date of purchase. All returns must be received within 15 days of the RMA number.
What is the Length of This Warranty?
This warranty is good for one (1) year on all parts of the system, excluding consumables as set forth above. Warranty coverage begins on the date of purchase, and expires on the same date 1 year later. The purchase date is the date your order was placed, as dictated by our records.
What are the Limitations of This Warranty?
This warranty is applicable to the original purchaser and original installation only. Resale or relocation of the System nullifies any warranty, written or implied. Systems purchased for commercial use are also excluded from warranty coverage.
Failure to meet the following conditions will void this warranty:
The Reverse Osmosis System must be hooked up to a potable cold water supply.
The ph of the water must not be lower than 3 or higher than 11.
The water pressure must be between 40 and 80 pounds per square inch.
Incoming water temperature cannot exceed 105' F (40.5' C).
25
NOTES Connection Diagram for Zoi RO Systems
Arrows indicate flow direction
To
Ice Maker
25
26
24 Taste & Odor Post Filter
BLUE
Faucet Line
Optional Ice
Maker Kit
Screwed onto storage tank
Alkaline Filter 23
Large
32
20
YELLOW/BLACK
Wastewater Line K2548
22 pH Filter
31
Medium
Clamps around drain pipe
17
16
Check Valve
CV
15
13
14
RO Membrane
Solid Blue with a stem on each end
12
Small
30
Connects to
UV Transformer
9 10 IN OUT 11
Ultra-Violet (UV) Filter
18
(Water can flow either direction depending on install)
2
White Filter w/ blue caps
Carbon
5
White Filter w/ blue caps
GAC
5
Solid White
Filter
8
Sediment
2
RED/ORANGE
Feedwater Line
7
27
3
6
3
4
29
OUT
IN
28
3
Closed
1
Connects to cold water line iii
NOTES Quick Troubleshooting Guide
Note: To remove tubing from quick connect fittings, hold in on the small collet ring at the end of the fitting, push this ring in towards the fitting while gently pulling out on the tubing. This releases the tubing from the fitting and it will slide out easily
Problem Possible Cause Solution
No Water
Production *
Waste Water
Runs
Constantly **
Tank Not
Holding
Water***
UV Bulb Not Lit
No Water Supply
Insufficient Pressure
GAC Filter Upside Down
Clogged filters
Fouled Membrane
Ensure water supply is turned on
Use booster pump if pressure is <40psi
Single gasket needs to be facing up
Replace filters
Replace membrane
Defective Check Valve Replace check valve
Defective Auto Shut Off Replace auto shut off valve
Defective Flow Restrictor Replace flow restrictor
Obstruction In Line
Ensure valves open & no kinks in lines
Trace flow of water to pinpoint cause
Insufficient Pressure Use booster pump if pressure is <40psi
Clogged filters
Fouled Membrane
Replace filters
Replace membrane
Defective Check Valve Replace Check Valve
Defective Auto Shut Off Replace auto shut off valve
Defective Flow Restrictor Replace flow restrictor
Obstruction In Line
Ensure valves open & no kinks in lines
Trace flow of water
No Pressure in Tank
Defective Check Valve
Check pressure in tank, min.:4psi, max.:10psi, with tank empty.
Replace check valve
No Power
Bulb Burnt out
Ensure transformer is plugged in and verify outlet receives power
Replace Bulb—Replaced every 12 months, regardless of appearance
Transformer Defective Transformer should output 125mA
* Water output will decrease as the tank empties and will only be a quick drip or slow stream when the tank is empty. This is normal.
** Water will run down the drain whenever the system is filling the tank. How long it runs depends on water pressure, filter and membrane condition, membrane size, system configuration, and amount of water taken from the tank. Average times for refilling the tank range from 30-45 minutes for a couple glasses of water up to 4-5 hours to completely fill the tank.
*** The standard tank will hold a maximum of about 3.2 gallons of water, the upgrade tank will hold about a maximum of about 10.3 gallons of water. Actual storage capacity may be less depending on system configuration and water pressure.
23
4.
Systems with UV Check flow coming out of the UV filter, if flow is reduced there is an obstruction in the UV housing.
Unplug the UV before checking for obstructions
5.
Remove the waste water (yellow) line from the membrane housing (a capillary flow restrictor is installed in the line) and check water flow; there should be a steady flow of water. If there is no water flow and water is reaching the membrane, the membrane is fouled and needs replaced.
6.
Check flow after the flow restrictor. Flow should be reduced, but should still be coming out in a steady stream. If flow is the same or if flow is completely gone, the flow restrictor is defective and needs to be replaced.
7.
Check the line coming from the check valve on the membrane to the auto shut off valve (refer to the connection diagram if you are unsure where the check valve is). You should get a steady drip or a slow stream. If there is no flow, remove the check valve (simply unscrew counterclockwise) and test again.
If flow is achieved by removing the check valve, replace the defective check valve. If removing the check valve does not solve the problem, either your pressure is too low (common on new installations, 40psi minimum is required) or the membrane is fouled (more common on older systems).
8.
Check line connecting the auto shut off to the T-fitting on the next filter (refer to connection diagram if you are unsure which filter is next). Flow should be the same here as it was coming out of the membrane. If not, the auto shut off valve is stuck and not allowing water through, replace the auto shut off valve.
9.
Ensure tank ball valve closed and check the flow of water after each of the inline filters. (Inline filters may include post filter, pH filter, and alkaline filter, depending on your system.)
Remove the line after each filter and check the water flow.
Flow should be close to the same through each filter as it was coming from the auto shut off valve. If significantly reduced flow is found after one of the filters, replace the filter.
10.
Remove the line connected to the faucet (blue) and check flow there. If flow is restricted, replace the tubing between the final filter on the system and the faucet. If flow through the line is fine but there is no water from the faucet, replace the faucet.
Contents
Important Information ........................................................................ ii
Maintenance Log: .................................................................................. ii
Parts List .................................................................................................. ii
Connection Diagram for Zoi RO Systems ..................................... iii
Pre-installation Preparation .............................................................. 1
Brief Technical Summary of the Filtration Process ...................... 1
Water Purification Summary: ............................................................ 1
System Maintenance Summary: ....................................................... 2
Pre-installation Check List ................................................................. 2
Parts Checklist ..................................................................................... 3
System Installation ............................................................................... 4
Filter Upgrade Installation ................................................................ 4
Faucet Installation .............................................................................. 5
Drilling a hole for the faucet ......................................................... 5
Mounting the Faucet: ..................................................................... 6
Storage Tank: ....................................................................................... 7
To Prepare the Tank: ...................................................................... 7
Feed Water Installation: .................................................................... 7
Flex line Instructions ...................................................................... 8
Copper Instructions ........................................................................ 8
Drain Saddle Installation:................................................................... 8
To install: ........................................................................................... 9
Connecting the system: ....................................................................... 9
Feed Water Line – RED .................................................................... 10
Tank Line – CLEAR ............................................................................ 10
Faucet (Good Water) Line – BLUE ................................................. 10
Drain (Waste Water) Line – YELLOW............................................ 10
Example of Connected System ..................................................... 11
Optional Ice Maker Kit Installation ............................................... 11
System Start Up: ................................................................................. 11
Preparing the system for use: ....................................................... 12
System Maintenance ......................................................................... 13
Filters: ................................................................................................. 13
To change filters: .............................................................................. 13
O-rings: ............................................................................................... 15
Housings ............................................................................................. 16
UV Filter: ............................................................................................ 16
To change the lamp: .................................................................... 16
v
To clean/replace the quartz sleeve: ......................................... 16
Membrane: ......................................................................................... 17
To change the membrane: .......................................................... 18
Estimated System Life..................................................................... 19
System Sanitization: ........................................................................ 19
Sanitization Procedure: ............................................................... 20
Troubleshooting ................................................................................. 21
Tracing Water Flow .......................................................................... 21
Reverse Osmosis System Limited Warranty .............................. 25
ensure the lines are flushed well. Make sure to close the faucet
2-3 times to allow water to fill the tank, then open again to flush the tank.
12.
Install new filters (the inline filters MUST be replaced as detailed in the filter changing instructions, since the chlorine will exhaust them).
13.
Insert membrane (either the original or a new one) into membrane housing.
14.
Ensure housings are tight and all connections are secure.
15.
Flush the system as detailed in the filter change instructions to clean out the new filters.
16.
Your system is now sanitized and ready to use.
Troubleshooting
Tracing Water Flow
Note: Tank valve needs to be shut off unless otherwise indicated.
When tracing water flow, shut feed water valve off and remove line to be checked from fitting. Turn feed water valve back on, ensuring it is fully open before checking flow. Repeat this process with each step until the problem is found.
1.
Check feed water line (red) connected to the inlet side of the clear housing on the bottom of the system. Flow should be strong and forceful. If not, ensure water supply is on and feed water valve is open. If water supply is on and feed water valve is open and still no water, replace the line connecting the system to the feed water valve.
2.
Check flow on line coming from 3rd (white) housing connected to the auto shut off valve (ASV, the white block behind the membrane with 4 connections). Flow should be close to the same as before the filters. If not, verify the middle filter is installed with the gasket end facing up. If installed correctly and flow is still significantly reduced, replace the filters.
3.
Directly across the ASV is a line running to either the single fitting end of the membrane OR the UV filter, depending on system configuration. Check the flow, if flow is significantly reduced or none at all, the auto shut off valve is blocking flow.
Open the faucet to relieve any pressure on the system, and check again. If flow is still impeded, the auto shut off is worn out and needs replaced
21
the water in your system may still contain bacteria. The bacteria still has the opportunity to grow in your system and damage your membrane, so even if you have a UV filter it is recommended that you use this procedure. We recommend sanitizing during a filter change, that way the old filters can be removed and thrown away, the system can be sanitized and new filters put in.
Sanitization Procedure:
1.
Turn off the feed water supply. This is done by closing the angle adapter ball valve. The valve is closed when the handle is at a 90 ° angle to the tubing (when handle is NOT parallel to tubing).
2.
Open the faucet to allow the tank to empty. This water may be saved if so desired. Leave the faucet open until no more water comes out.
3.
Close the faucet.
4.
Pull the system out to where it can be easily worked with. If the system was installed with enough tubing to do so, simply pull it out to where it can be worked on. If the system does not have enough tubing, you will need to disconnect the lines to pull it out. (When changing the membrane, it helps to have a towel handy, as some water may leak out.) Make note of which tube goes where to ensure the system will be hooked up the same way it was.
5.
Remove all filters and the membrane from their housings; leave the inline filter(s) (the post filter, as well as the DI & pH/Mineral filter if the system has them) in place.
6.
Add one capful (2 tsp or 10ml) of 5 ¼ % bleach (any household bleach, such as Clorox®, will work) to each filter housing and the membrane housing.
7.
If the system was unhooked, hook it back up now.
8.
Open the feed water supply and allow water to fill the housings. Open the tank valve and allow 5 - 10 minutes for water to fill the tank.
9.
Open the faucet to allow solution to enter lines. Close the faucet and feed water line when water begins to come out of the faucet.
10.
Let solution stand in system for 15 minutes.
11.
Open the feed water line and faucet and allow water to run through the system, 15 - 20 minutes is recommended to
Pre-installation Preparation
IMPORTANT: Read through the entire instruction manual before beginning installation. Abundant Flow Water is not responsible for any damage, injury, or monetary loss incurred from failure to read and follow instructions.
Brief Technical Summary of the Filtration Process
Water enters the filter system and passes through a series of prefilters. The sediment filter removes particulates such as dirt and sediment. The GAC (granular activated carbon) removes a wide range of chemicals (including chloramines), tastes, and odors. The carbon block filter removes chlorine and any tastes and odors the
GAC filter might miss. The pre-filters protect the membrane and should be changed regularly to ensure maximum performance and membrane life. (NOTE: Some special order systems may have different pre-filters). The water is then purified using a process called reverse osmosis (RO). As the heart of the purification system, the RO process uses a semi-permeable, spiral-wound membrane to separate and remove dissolved solids, organic, pyrogens, sub-micron colloidal particles and bacteria from the water. Feed water is delivered under pressure at about 60 PSI through the permeator where water permeates the minute pores of the membrane and is delivered as purified water. Impurities in the water are concentrated in the reject stream and flushed to drain. The RO Membrane is capable of removing 90% to 95% of contaminates present in the water. The optional UV filter uses ultra violet light to destroy bacteria and viruses. The optional inline pH/mineral filter ensures a neutral pH and adds beneficial minerals back into the water. The optional alkaline filter increases water alkalinity, adds additional minerals, and lowers oxygen reduction potential (ORP). The post filter gives a final polishing to ensure clean tasting water.
Water Purification Summary:
Stage 1 : Sediment - Traps dirt, sediment, & particulates
Stage 2 : GAC - Chloramines, Tastes, Chemicals, & Odors
Stage 3 : Carbon Block - Chlorine, Tastes, Chemicals, & Odors
Stage 4 : UV (Upgrade) - Kills bacteria, viruses, & cysts
Stage 5 : RO TFC Membrane - 90-95% of contaminates
Storage : Pressurized Tank
1
Stage 6 : pH (Upgrade) - Neutralizes acid/adds minerals
Stage 7 : Alkaline (Upgrade) – Raise alkalinity, lower ORP
Stage 8 : Post - Polishing filter to ensure clean, fresh tasting water
Delivery : Dedicated RO Faucet
System Maintenance Summary:
Filters: Filter maintenance will vary depending on water quality and water usage. For most homes with average water quality and usage, every 6 months is usually sufficient. For higher water use and/or dirtier water, more frequent filter changes may be needed.
Filters need to be changed at least once a year. If equipped, the
UV bulb should be changed every 12 months. Refer to the front cover for the filter set specific to your system. Replacement filters available online at www.afwfilters.com or by calling 785-735-9769.
Membrane: Average membrane life varies from 2-4 years depending on a number of factors. Reduced water production or quality may indicate a fouled membrane, or a TDS meter can be used to monitor the membrane. The membrane should be changed at least every 4 years.
Sanitization: It is recommended that the system is sanitized once a year to prevent bacterial build up and ensure a clean system.
Even in homes with no known bacteria problem or bacteria prevention in place it is a good idea to sanitize the system. If used in a home with a known bacteria problem, more frequent sanitization may be a good idea.
Pre-installation Check List
1.
Read through and familiarize yourself with these instructions and the installation process. This will ensure you have the proper tools, parts, and abilities to install the system before beginning, rather than having to stop halfway through because of missing parts, incorrect tools, or the inability to perform a required task.
2.
Check and follow all local plumbing. Going against plumbing codes is illegal, and can cause problems. Abundant Flow Water is not responsible for any problems resulting from improper installation or installations violating local plumbing codes.
3.
Determine installation locations, including feed water supply, drain, faucet, filter system, and storage tank. Ensure you have room for everything, and plan room for future filter changes.
4.
Familiarize yourself with the quick connect fittings. Your system uses quick connect fittings. There is a collet ring at the end of the the system is turned off.
12.
If the system was unhooked to change the filters, hook it back up now. Open the angle adapter ball valve on the feed water line, and open the tank ball valve.
13.
Open the faucet, and tilt the system back and forth and side to side to help work the air out of the lines.
14.
Allow the system some time to start producing water from the faucet, depending on the system and water pressure this may take up to 30 minutes. Once you are getting a steady flow of water (anything from a steady drip to a small stream, depending on membrane size and water pressure), shut the faucet off.
15.
Allow the system to fill the tank. Depending on the system and water pressure, this can take anywhere from 1 - 5 hours.
16.
Once the tank has filled, open the faucet, allowing all the water to drain until flow from the faucet is down to the slow drip or stream seen in step 14. This flushes the system, cleaning the membrane and preparing it for use.
17.
Repeat steps 15-16 at least once to ensure thorough flushing of the new filters.
18.
Your membrane is now changed and the system is ready to use again.
Estimated System Life
The estimated system life is typically about 10 years. After this point wear and required replacement costs typically outweigh the costs and advantages of replacing the entire system with a new unit.
System Sanitization:
Important Note: Reverse Osmosis water purification systems remove most contaminates in drinking water, however there is no guarantee on the quality of the final product. In addition to that, it is important that you are aware that bacteria can grow within your RO system, even in homes with no known bacteria problems, and thus we recommend using this sanitization procedure at least one a year to prevent and eliminate any bacteria growth. If using on a water supply that has a known bacteria problem, more frequent sanitization may be necessary. If your system has a UV filter this will eliminate bacteria in your final product water, however, the UV filter is one of the last stages, so the majority of
19
To change the membrane:
Note: The tank will need to be emptied when replacing the membrane. If you would like to save the water in the tank for use, follow the instructions below, opening the faucet and collecting the water from the tank after turning the feed water off.
1.
Turn off the feed water supply. This is done by closing the angle adapter ball valve. The valve is closed when the handle is at a 90 ° angle to the tubing (when handle is NOT parallel to tubing). If saving water from the tank, do so after closing the valve.
2.
Shut the ball valve on the tank. The valve is closed when the handle is at a 90 ° angle to the tubing (when the handle is NOT parallel to the tubing).
3.
Open the faucet to release any remaining pressure.
4.
Pull the system out to where it can be easily worked with. If the system was installed with enough tubing to do so, simply pull it out to where it can be worked on. If the system does not have enough tubing, you will need to disconnect the lines to pull it out. (When changing the membrane, it helps to have a towel handy, as some water may leak out.) Make note of which tube goes where to ensure the system will be hooked up the same way it was.
5.
Disconnect the tube feeding the membrane (the tube going to the single fitting on the membrane housing cap). If unsure how to disconnect the quick connect fittings, refer to the section on quick connect near the beginning of the manual.
6.
Remove the membrane housing cap (when looking at the fitting on the cap it will turn counterclockwise to loosen).
7.
Remove the membrane from the housing. A pair of needle nosed pliers may be needed to grip the end of the membrane.
To remove, gently pull with a twisting motion and the membrane should slide out.
8.
Lubricate the O-rings on the membrane with a silicon based lubricant (vegetable oil may be used if silicon lubricant is not available), and push back into the housing.
9.
Lubricate the O-ring on the membrane housing (some housings have 2) and screw the membrane housing cap back onto the housing.
10.
Push the tubing back into the fitting on the membrane cap.
11.
If the filters need changed, now is a good time to do so, since fitting that grips the tubing and holds it in place. To remove, simply hold the collet ring against the fitting and pull the tubing out. To replace tubing, just push it into the fitting, it will slide in easily about 1/4” then stop, apply a little more pressure and it will slip in another 1/8” or so and seal in place.
5.
Familiarize yourself with any purchased upgrade kits. If you ordered any kits to upgrade your system, read through the instructions on how to install it, as it is usually easier to install any upgrades before installing the system.
6.
Check to ensure there are no missing parts. Use the parts checklist on the following page to make sure all the parts listed are present. If anything is missing, call us and we will get replacements out as soon as possible.
7.
Assemble the tools you will need. Depending on where the system is being installed and the plumbing, the tools needed may vary. You will need a Phillips head screwdriver, drill, wrenches, pliers & PTFE tape. You will also need a sharp knife or scissors to cut the tubing (when cutting tubing, ensure the end is smooth and straight, this will ensure a good seal and prevent leaks). This list is just a start, reading through the instructions and determining where you are installing the system will give you a better idea of everything needed.
8.
Ensure the following conditions are met:
Feed Water
Condition
Minimum Maximum
Inlet Pressure
Temperature
40 psi
40 ° F
80 psi
100 ° F pH Level
TDS Level
For pressure less than 40psi a booster pump will be required. If pressure is less than 50psi a booster pump or permeate pump is recommended. If other conditions are not met contact us for a solution. NOTE : Failure to meet the above conditions will void the warranty on the system.
3
0 ppm
11
2000 ppm
Parts Checklist
In addition to the RO system, faucet, storage tank, and UV transformer (if a UV was ordered), you should have the following
3
parts (pictures and descriptions represent the most common style, actual style may vary):
Tank Ball Valve - White & blue plastic valve with female threads and quick connect fitting. Installed on storage tank, valve is open when handle is in line with tubing.
Angle Shut-off Adapter - White & blue plastic valve with 3/8” female x 3/8” male threads and quick connect fitting. Installed on standard cold water shut off, valve is open when handle is in line with tubing
Drain Saddle - Black plastic clamp with compression fitting, 2 bolts with nuts, and rubber seal. Clamps around the drain pipe and connects to the waste water line.
Quick connect faucet fitting - White plastic fitting with 7/16” NPT female threads and quick connect fitting. Connects to the RO faucet shank and product water line.
A plastic wrench (for tightening and removing the filter housings) is also included.
Once you have read through the entire instruction manual and familiarized yourself with the installation process, you may proceed with installing the system.
System Installation
Filter Upgrade Installation
If you purchased a system with a filter upgrade kit for advanced filtration, these instruction will walk you through getting the additional filtration setup on your new system. If you did not get additional filtration, skip to “Faucet Installation”
1.
First, remove all the filter upgrade kit parts to ensure that everything is present. You should have: the inline filters relevant to the exact system you ordered (see connection diagram for available filters), two (2) quick connect fittings for inline filters that have threaded ports (if applicable), two (2) clips for each filter, a 2-3 foot length of tubing, and one (1) stem elbow fitting for each filter (two (2) for the UV filter).
2.
Next, install the quick connect fittings into any filters that have threaded openings. Put 2-3 wraps of PTFE on the threads of each handle is at a 90 ° angle to the tubing (when the handle is NOT parallel to the tubing).
3.
Open the faucet to release any remaining pressure.
4.
Unscrew the cap on the UV filter and carefully remove. The quartz sleeve is secured inside the cap.
5.
Inspect the sleeve. The cleaner it is the better it will work. Light build up can be cleaned off with a vinegar solution, be sure to avoid touching the sleeve with bare hands as fingerprints can cause buildup that will block the UV light.
6.
If heavy build up is present the sleeve will need to be removed and thoroughly cleaned (by soaking in a vinegar solution) or replaced.
7.
To remove the sleeve, gently grip and twist (clockwise or counterclockwise doesn’t matter, just stick with one direction, the goal is to loosen it) while pulling it away from the cap.
NOTE: Care must be taken when removing the sleeve, as it can break if too much force is applied, creating sharp edges that can cause injury.
8.
To replace the sleeve, use silicon based lubricant or vegetable oil (NOT VASELINE) and lubricate the O-rings inside the cap.
Gently push and twist the sleeve in place until it is fully seated in the cap.
9.
Screw the cap back onto the UV filter, and turn your water back on, checking for any leaks
Membrane:
The RO membrane will last an average of 2 –4 years, depending on water quality, water usage, frequency of filter changes, and quality of filters used. Reduced water quality, reduced production rate, or no production can be an indication of a fouled membrane, but there may not always be these signs to tell you the membrane is bad. The best way is to monitor the rejection rate of the membrane using a TDS meter. A functioning membrane should be removing a minimum of 90% of contaminates under normal conditions. To test this, simply compare the TDS of your tap water to the TDS of the water from the membrane (before it goes to any other filters). For example, if your tap water has a TDS of 400ppm, after the membrane your TDS should be 40ppm or less. If you do not wish to use a TDS meter, it is recommended that you change your membrane at least every 4 years.
17
warranty on the system. We are not responsible for any damaged caused by using Vaseline or other petroleum lubricants. To ensure a good seal and minimize any possibility of leaks, it is recommended you replace your O-rings periodically, usually every
1-2 years.
Housings
With the regular stress of removal and tightening, filter housings will weaken over time. To help prevent unwanted system failure the filter housings on your system need to be replaced every 5 years.
UV Filter:
The UV filter uses a bulb to kill bacteria. When the filter is plugged in and operating, the white cap where the wire comes out will glow a purplish color. If you ever notice that the filter is not glowing it means the UV bulb is no longer working. IMMEDIATELY
STOP using the system, as bacteria may be contaminating your water. Replace the bulb and sanitize the system to ensure safe, treated drinking water. The bulb does wear out and needs to be replaced; recommended replacement is every 12 months. It is important to note that the bulb may glow for longer, but the intensity of the bulb diminishes over time and after 12 months full, effective treatment is not assured.
Buildup on the quartz sleeve can also decrease the amount of effective light that treats the water, so regular checking and cleaning of the sleeve is recommended.
To change the lamp:
The lamp is enclosed inside a quartz sleeve, so the water does
NOT need to be shut off to change the lamp. Unplug the white wire from the transformer and grasp it near the white cap on the end of the filter. Ensure you have a firm grip on both the filter and the wire, and pull on the wire. The white cap will pull out with the lamp. Then, simply push the new lamp in place.
To clean/replace the quartz sleeve:
1.
Turn off the feed water supply. This is done by closing the angle adapter ball valve. The valve is closed when the handle is at a
90 ° angle to the tubing (when handle is NOT parallel to tubing).
If saving water from the tank, do so after closing the valve.
2.
Shut the ball valve on the tank. The valve is closed when the fitting and tighten until snug, making sure to not over-tighten, which would cause the filter to crack or could strip out the threads.
3.
Now we will install the filter(s) in the order shown by the diagram on the back of this sheet. Start by installing the UV filter
(if applicable). First, cut the line between the auto shutoff valve
(ASV) and the membrane housing, making sure that you leave enough tubing coming from the ASV to reach the UV filter. Next, place a stem elbow on the end of the piece of tubing. Then run a piece of tubing from the membrane housing cap to the opposite side of the UV filter. Place a stem elbow on the end of this tubing that connects to the UV filter also. Connect the other end of the tubing to the membrane housing. Place the relevant clips onto the membrane housing, push the UV filter into the clips, and insert the stem elbows into the UV filter.
4.
Next, disconnect the tee fitting from the carbon post filter that is currently installed on the RO system and remove the filter.
Place the relevant clips onto the membrane housing, then push the first filter into the clips, making sure the water flow is going the same direction as the carbon filter was going. Insert the tee fitting into the input side of this first filter.
5.
Follow the same process for each filter, making sure that the flow coming out of the previous filter enters the input side of the next filter, following the direction of flow indicated on the filter.
Faucet Installation
Locate the installation point for the faucet; you will need a hole at least 1/2” in diameter for the RO faucet shank. If the sink has a sprayer the RO faucet may be installed in the hole used for the sprayer, simply disconnect the sprayer and plug the sprayer connection. If the sprayer hole is not an option you will need to drill a hole. To drill a hole, determine where it will be located before starting. You will need a 2” flat surface no more than 2” thick. Ensure the chosen location will not interfere with anything below, and position the faucet so it will empty into the sink and can swivel freely for convenience. Once you have confirmed your faucet location, proceed with drilling the hole in your sink.
Drilling a hole for the faucet
Be careful when drilling the faucet hole. Be sure to drill slowly to prevent chipping or scratching, and be sure to wear proper safety
5
equipment to protect yourself.
1.
Mark the center of the hole with a pencil, marker or other marking device
2.
Determine your sink type: a.
Porcelain, Enamel, or Ceramic on Metal: Using a 1/4” masonry bit, carefully (using a slow speed and light pressure) drill a pilot hole through the sink. If drilling through a ceramic on metal sink, stop when you reach the metal portion, switch to a 1/4” metal cutting bit and continue. b.
Stainless Steel or Cast Iron : Using a 1/4” metal cutting bit, carefully drill a pilot hole through the sink.
3.
Continue to enlarge the pilot hole until the hole is 1/2".
4.
Clean up any rough or sharp edges.
Note: Air gap faucets are required by some local plumbing codes.
These faucets require a 1-1/4" hole in the sink rather than the 1/2" hole required by the standard RO faucet. If a hole large enough (1-
1/4") is not already available, special tools (such as a chassis punch or a Relton cutter) may be required. Contact your local plumber or contractor if you are unable to make the required hole yourself. If an air gap faucet is required, we provide a number of different styles and colors; contact us for pricing and availability.
Once the faucet location has been prepared, move on to the next step: Mounting the
Faucet.
Open
Escutcheon Plate
Countertop
Black O-ring washer
Locating Washer
Star Washer
Mounting the Faucet:
1.
Remove all parts from the
RO faucet shank. Using
Figure 1, gather the pieces shown. NOTE: The diagram is for the standard RO faucet, an upgraded faucet
Lock nut has them.) To replace them, remove the tubing and/or fittings from each end of the filter (refer to section on quick connect fittings near the beginning of the manual if you are unsure how to do this) and replace in the new filter, paying careful attention to the direction of flow as indicated on the filter, and ensuring the new filter is installed in the same direction as the old filter. Do this with each inline filter your system has.
8.
If the system was unhooked to change the filters, hook it back up now. Open the angle adapter ball valve on the feed water line, and open the tank ball valve.
9.
Open the faucet, and tilt the system back and forth and side to side to help work the air out of the lines
10.
Allow the system some time to start producing water from the faucet, depending on the system and water pressure this may take up to 30 minutes. When the water first comes out it may be black as the carbon fines in the post filter rinse out, this is normal. Once you are getting a steady flow of water (anything from a steady drip to a small stream, depending on membrane size and water pressure), shut the faucet off.
11.
Allow the system to fill the tank. Depending on the system and water pressure, this can take anywhere from 1 - 5 hours.
12.
Once the tank has filled, open the faucet, allowing all the water to drain until flow from the faucet is down to the slow drip or stream seen in step 10. This flushes the system, cleaning the filters and preparing them for use.
13.
Repeat steps 11-12 at least once to ensure thorough flushing of the new filters.
14.
Your filters are now changed and the system is ready to use again.
O-rings:
The filter housings on the system utilize O-rings (black rubber washers, located in a grove right below the threads on the housing) to seal themselves. To prevent leaks it is recommended to check the O-rings every time the housings are opened. Ensure there are no nicks, kinks, or gouges in the O-ring. If damage is found, replace before continuing, otherwise, use a silicon based lubricant (vegetable oil can be used if no silicone lubricant is available) and lubricate the O-ring before replacing the housing.
DO NOT USE VASELINE! This will damage the O-rings and void any
15
1.
Turn off the feed water supply. This is done by closing the angle adapter ball valve. The valve is closed when the handle is at a 90 ° angle to the tubing (when handle is NOT parallel to tubing). If saving water from the tank, do so after closing the valve.
2.
Shut the ball valve on the tank. The valve is closed when the handle is at a 90 ° angle to the tubing (when the handle is NOT parallel to the tubing).
3.
Open the faucet to release any remaining pressure.
4.
Pull the system out to where it can be easily worked with. If the system was installed with enough tubing to do so, simply pull it out to where it can be worked on. If the system does not have enough tubing, you will need to disconnect the lines to pull it out. (When changing filters, it helps to have a towel handy, as some water may leak out.) Make note of which tube goes where to ensure the system will be hooked up the same way it was.
5.
Remove the first filter housing. To remove, use the filter housing wrench supplied with your system. When looking down at the top of the system, the filter housing will turn clockwise to loosen, counterclockwise to tighten. Once the filter housing has been removed, pull the filter out and replace with the new one. At the top of each housing is an O-ring, when changing filters it is recommended to remove the O-ring and check for any damage such as nicks, gouges, or kinks. If damage is found, replace before continuing, otherwise, use a silicon based lubricant (vegetable oil can be used if no silicone lubricant is available, avoid petroleum based lubricants such as
Vaseline) and lubricate the O-ring, place it in the filter housing and screw the housing back in place. This will help prevent leaks.
6.
Repeat step 5 with each housing, replacing the old filter with the similar new filter and checking the O-rings. If any of the filters have only one gasket (the middle filter on most systems will have only one gasket) the filter will need to be installed with the gasket at the top of the housing, unless dictated otherwise by the filter itself.
7.
Once the pre-filters (the filters in the housings) have been changed, it is time to change the inline filter(s) (the post filter, as well as the pH/Mineral filter & Alkaline filter if the system may look slightly different than the one pictured, but the parts should be similar.
2.
Place color matched washer onto faucet shank, followed by the small rubber washer. Position the faucet in the mounting location by sliding the shank through the mounting hole.
3.
On the underside of the mounting hole, slide the large rubber washer and locking washer in place, then tighten the faucet nut in place until secure.
4.
Once your system is installed, you can hook up the product line to the faucet. The best way to do so is to wrap the bottom of the faucet shank with 3-4 wraps of PTFE tape, then attach the quick connect faucet fitting. The product line will then push directly into the fitting. An alternate method of attaching the line is to slide the line nut over the product line, followed by the ferrule, then push the insert into the end of the line. Once that is done simply push the end of the product line into the bottom of the faucet shank as far as it will go, then tighten the line nut to secure it in place.
Storage Tank:
As the RO system makes water it pushes it into a tank to store it, and a pressurized bladder in the tank pushes it back out (through the same opening) when requested (such as opening the faucet).
The large male threaded fitting on one end of the tank is the inlet and outlet of the tank. A pressure valve on the side of the tank
(usually covered with a blue screw-on cap) is used only for checking and adding air to the bladder. The tank is shipped with 4-
6psi of air pressure in the bladder, and is sufficient in most cases.
Pressure may be increased to no higher than 10psi when the tank is empty, this will cause water to come out of the faucet a little faster if so desired. NOTE: As the tank is emptied, pressure from the faucet will decrease, this is normal.
To Prepare the Tank:
1.
Wrap the threaded nipple on the end of the tank with 3-4 wraps of PTFE tape.
2.
Install tank ball valve on prepared nipple, hand tight only. When connecting the system the product line connects here.
Feed Water Installation:
1.
The feed water assembly consists of a 3/8” angle valve adapter.
7
2.
Locate cold-water angle shut off valve underneath the sink, usually on the right side, and turn it off. Open cold water faucet to release the pressure. On single handle faucets, turn the hot water off to prevent cross over. If water is not stopped completely, turn off main water supply
3.
The angle shut of adaptor is installed directly on the on the cold water angle shut off valve.
Flex line Instructions
Loosen nut and separate cold water line from angle shut off valve. Ensure the Oring is in place on the angle valve adapter and screw in place on the angle shut off valve. If washer in flex line is worn or damaged, replace before continuing to prevent any leaks. Gently bend flex line so that it will fit over the angle valve adapter and tighten flex line onto angle valve adapter.
Copper Instructions
Loosen nut and separate cold water line from angle shut off valve. You will need to cut a piece of the copper tube about
3/4" to 1" (measure to determine the exact cut needed) so the angle valve adapter can fit between the angle shut off valve and the copper line. Ensure the O-ring is in place on the angle valve adapter and screw in place on the angle shut off valve. If washer in copper line is worn or damaged, replace before continuing to prevent any leaks. Push the copper pipe into the angle valve adapter and tighten down the compression nut.When connecting the system the feed water line connects to the angle valve adapter.
Drain Saddle Installation:
The drain saddle consists of two (2) halves, (one half has a fitting on it), two (2) bolts with nuts, & a rubber seal. It is used to direct the waste water from your system down the drain. Depending on where the saddle is located, you may hear water running down the drain when the system is making water, this is normal. If the sound is annoying, the drain line may be pushed farther in to help
NOTE: The system will automatically turn on whenever water is drawn out of the tank. When the system is on & making water there will be water going down the drain, this is normal. Once the tank is full pressure build up in the system will activate the auto shut off valve, cutting the water supply to the membrane and stopping the flow of water down the drain. How long it takes for the wastewater to shut off depends on many variables, including the amount of water taken out and water pressure.
System Maintenance
Filters:
Filters need changed regularly to ensure protection of the membrane and high purity water production.
Refer to the chart below for the specific filter set needed for your system. Filter kits, as well as individual and specialty filters may be ordered securely online at www.afwfilters.com or by calling 785-
735-9769. With average usage and normal water conditions filters should be changed every 6 months. The more water you use or the dirtier your water the more often you will want to change filters. If the first filter (sediment filter) gets dirty quickly it may need changed more often than the rest, part number for the individual sediment filter is RF-SED10-5. All filters (excluding the membrane) should be changed at least every 12 months.
To change filters:
Note: The tank will need to be emptied when changing filters. If you would like to save the water in the tank for use, follow the instructions below, opening the faucet and collecting the water from the tank after turning the feed water off.
13
from the UV filter into the transformer and plug the transformer into any standard 110v outlet. When the UV bulb is working you will see a purple glow from the end of the UV filter. NOTE: When first plugged in the UV filter may take a minute or two before it lights up, this is normal. Once plugged in the light will remain on and should not be unplugged except to change the bulb, this ensures effective treatment.
Preparing the system for use:
Note: Ball valves are open when the handle is inline (parallel) with the tubing (Fig. 5)
1.
Double check all the connections, ensure they
Open Closed
Fig. 5 are all connected and secure.
2.
Ensure all filter housings are tightened down, using the filter housing wrench included with your system.
3.
Slowly open the ball valve on the feed water connection.
Water will fill the filter housings.
4.
Open the tank ball valve.
5.
Check all connections, ensuring there are no leaks.
6.
Open the faucet and tilt the system from side to side and back to front, this helps work the air out of the system.
7.
Allow the system some time to start producing water from the faucet, depending on the system and water pressure this may take up to 30 minutes. When the water first comes out it may be black as the carbon fines in the post filter rinse out, this is normal. Once you are getting a steady flow of water (anything from a steady drip to a small stream, depending on membrane size and water pressure), shut the faucet off.
8.
Allow the system to fill the tank. Depending on the system and water pressure, this can take anywhere from 1 - 5 hours.
9.
Once the tank has filled, open the faucet, allowing all the water to drain until flow from the faucet is down to a slow drip or stream (about 5-10 minutes for the standard tank). This flushes the system, removing any preservatives from the membrane and cleaning off the filters.
10.
Repeat steps 8 & 9 at least once, ensuring the system is flushed and ready to use.
11.
The system is now ready to provide safe, purified water! alleviate it. Please note, pushing the drain line in farther than normal requires a good amount of force, as you are forcing the tubing past the typical stopping point. If doing so, please use caution to prevent any injuries.
To install:
1.
The drain saddle should be installed above the “P” trap and on the vertical or horizontal tailpiece
(see figure 3). A horizontal location is ideal, as it is more likely the waste water will be heard if installed on a vertical pipe.
2.
The position of the hole on the pipe should be marked and drilled with a 1/4" bit. If using a horizontal pipe, ensure the hole is made on the top of the pipe, so that standing water in the pipe will not leak into the drain saddle. NOTE: Drill through one side of the pipe only!
3.
Take the backing off of the rubber seal, center over the hole just drilled, and stick in place.
4.
Position the fitting half of the drain saddle over the hole in the drain pipe, then position the back half on the opposite side of the drain. Place one of the bolts through the fitting half into the back half and loosely thread the nut onto it. Repeat on the other side. Position the fitting on the fitting half of the saddle over the drilled hole and seal, then evenly tighten both nuts, being careful not to over tighten.
When connecting the system the drain line connects to the drain saddle fitting.
Connecting the system:
Once the previous steps have been completed the system is ready to be hooked up. To make future filter changes easier, we recommend positioning the system in a location that is easily accessed, or allowing enough tubing to move the system to where it can be easily accessed. This will allow you to change filters and
9
will save time since the system will not have to be unhooked.
We have included the pictures and descriptions along with color coded tubing to make connecting the system simple. If unsure, feel free to contact us for assistance. Refer to Pre-installation section for help with quick connect fittings. Please Note: Pictures are for reference only, system variations may occur.
Feed Water Line – RED
Connects from the inlet side of the first housing to the angle valve adapter.
Tank Line – CLEAR
Connects from the Tee-fitting (connected to membrane or UV filter depending on system configuration) to the ball valve on the tank. The tank valve is in the open position when the handle is in line with the tubing.
Faucet (Good Water) Line – BLUE
Connects from the outlet side of the post filter to the faucet shank. If using the compression fitting that comes with the faucet, slide the nut over the tube, followed by the ferrule, placing the insert into the end of the tube. Push the tube into the faucet shank and secure by tightening the line nut. (Refer to Figure 1)
Drain (Waste Water) Line – YELLOW
PRE-CONNECTED - Connects from the membrane to the drain saddle valve.
Example of Connected System
(System may differ from the one shown)
Optional Ice Maker Kit Installation
You can use your Reverse Osmosis system to provide filtered water for your refrigerator ice or water machine using kits available on our website or by calling us at 785-735-9769.
Find the line that leads to the faucet on the RO system. Cut line with sharp knife or scissors. Connect the T-connector to both ends of the line by pushing tubing into slip connectors firmly.
Cut a short length of tubing to insert into T-connector T-off. Insert other end of this tubing into shut off valve fitting. Connect tubing to other end of shut off valve and into ice machine or water machine. Lengths over 15’-20’ will lose pressure so use shortest route possible.
System Start Up:
After all the connections have been made it is time to prepare the system for use. If the system has a UV filter, plug the wire coming
11

Public link updated
The public link to your chat has been updated.
Advertisement