GMF BULLSEYE Owner's Manual 2 Pages
GMF BullsEye is an analog reverb pedal that creates reverb effects for electric or acoustic guitars, electronic keyboards and more. With two control knobs, you can quickly adjust the decay of the reverb (Dwell) and the amount of reverb mixed with the dry signal (Reverb). A true bypass switch engages and disengages the effect, and an LED indicator shows you when the effect is engaged and gets dim when it's time to change the battery. The pedal is made of heavy-duty steel, is fully shielded, and built to last.
advertisement
BULLSEYE
REVERB
OWNER’S
MANUAL
Thank you and congratulations on your choice of this product.
Features:
This is an analog reverb pedal that creates reverb effects.
Use it on electric or acoustic guitars, electronic keyboards and more.
Two control knobs let you quickly adjust Dwell, (decay of the reverb) and the amount of
REVERB mixed with dry signal.
A true bypass switch engages and disengages the effect.
An LED indicator shows you when the effect is engaged and gets dim when it's time to change the battery.
This pedal is made of
heavy ‐ duty steel, is fully shielded and built to last.
Precautions:
1) Read and follow these instructions before operating the unit.
2) Please heed all safety warnings and keep these instructions for future reference.
3) Do not use this apparatus near water or moisture.
4) Clean only with soft, dry cloth.
5) Do not install near a heat source such as radiators, heat registers, stoves, or other apparatus that produce heat.
6) Only use attachments/accessories specified by the manufacturer.
7) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as liquid has been spilled or objects have fallen into the unit, the unit has been exposed to rain or moisture, does not operate normally, or has been dropped.
8) Battery not included.
Use AC adaptor for ultimate performance.
Specifications:
Input Impedance 1M ohm
Output Impedance 100K ohm
Output Noise Level < 10mV
Controls
LED Indicator
Connectors
Power Supply
Pedal
INPUT
9V DC
Switch,
Indicates
‐
Dwell when
Jack,
the
unit
OUTPUT
Battery, AC
Knob,
is
Jack,
Reverb active
AC
Adaptor
Knob
–(also
Adaptor
serves
Jack
(9V as
battery
DC)
check indicator)
Current Draw
Dimensions
Weight
20mA
2.4”(W) x 3.8”(D) x 2.2”(H) ‐ (60x96x55)mm (Including knobs and jacks)
.625
lbs.
– 280 g (Without battery)
Panel
Description
9VDC – This unit can run off 9V battery or you can connect a 9V adapter.
The adapter must have a barrel connector with center negative.
The battery may be left in or taken out when using an adapter.
(To install or replace the 9V battery, loosen the screws on the bottom and remove the bottom plate.
Be careful not to scratch the unit.
Always remember to unplug your guitar cords
from the pedal to conserve battery life.
INPUT jack – This jack accepts input signals from a guitar, other electronic musical instrument, or from the output of another effect unit.
*The input jack also serves as the power switch.
Power is turned on whenever a plug is inserted into the INPUT
jack and is turned off when the plug is disconnected.
When not using the unit, you should disconnect any cord connected to the INPUT jack.
OUTPUT jack – Connect this jack to the input of your amplifier or input of another effect unit.
DWELL knob – This knob controls the decay of reverb.
Rotating the knob clockwise will increase the decay time.
REVERB knob – This knob controls the amount of reverb
mixed with the dry signal.
Rotating the knob clockwise will increase the amount of effect heard.
PEDAL SWITCH – This switch turns the effect on/off
WWW.GMFAMPS.COM
advertisement
Related manuals
advertisement